Napco Security Technologies Gemini Gem P3200 Users Manual P3200_RP1_WI818G.17

HARDWIRE WIRELESS

GEM-P3200

CONTROL PANEL/COMMUNICATOR

Programming the GEM-P3200 Control Panel with the

"Classic" GEM-RP1CAe2 Keypad and the "K Series" GEM-K1CA Keypad

WI818G 10/05 © NAPCO 2005

Quick Start (for "Classic" GEM-RP1CAe2)

1. Refer to the wiring diagram, connect Siren, Aux. Power,

PGM Output, Remote Bus, Earth ground, Zone and Tele-

phone wiring. NOTE: See Installation Instructions

(WI817).

2. Connect AC power first and then the battery.

3. Configure the keypad (see page 55).

4. Access the Easy Menu Driven (Dealer Program) Mode:

Press EEEEEEA

Press NO (g) until “ACTIVATE PROGRAM Y/N” appears on the

keypad display.

Press YES (F) to Enter Dealer Program Mode. Go to page 5.

Master Security Code

(on microshield)

"K Series" GEM-K1CA

GEMINI

SYSTEM READY

01/01/06 12:00 AM

ARMED

COMPUTERIZED SECURITY SYSTEM

STATUS

R 1 2 3

B 4 5 6

C 7 8 9 0

U

NEXT/YES

P

PRIOR/NO

Q

AREA

G

PROGRAMMING

INSTRUCTIONS

R

"Classic" GEM-RP1CAe2

GEMINI

SYSTEM READY

01/01/06 12:00 AM

ARMED

COMPUTERIZED SECURITY SYSTEM

STATUS

A 1 2 3

B 4 5 6

C 7 8 9 0

D

NEXT/YES

E

PRIOR/NO

F

AREA

G

Quick Start (for "K-Series" GEM-K1CA)

1. Refer to the wiring diagram, connect Siren, Aux. Power,

PGM Output, Remote Bus, Earth ground, Zone and Tele-

phone wiring. NOTE: See Installation Instructions

(WI817).

2. Connect AC power first and then the battery.

3. Configure the keypad (see page 55).

4. Access the Easy Menu Driven (Dealer Program) Mode:

Press EEEEEER

Press NO (Q) until “ACTIVATE PROGRAM Y/N” appears on the

keypad display.

Press YES (P) to Enter Dealer Program Mode. Go to page 5.

Master Security Code

(on microshield)

Publicly traded on NASDAQ Symbol: NSSC

THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN CONTROL PANEL FIRMWARE

VERSION 50 OR LATER.

IMPORTANT NOTE

This manual supports the keypad programming of the GEM-P3200 control panel with the NAPCO "classic" GEM-

RP1CAe2 keypad as well as the GEM-K1CA "K Series" keypad. The new "K Series" GEM-K1CA model offers the new

STAY and AWAY buttons with simplified functionality, along with the new MENU and ENTER buttons. Note: While the

instructions in this manual are depicted using the GEM-K1CA keypad, the manual applies to both the "classic" and the

"K Series" keypads.

Program Mode is the same for both keypads--only the button names have changed, as follows:

•The A button and the R button operate identically (in Program Mode) for both keypads.

•The D button and the U button operate identically (in Program Mode) for both keypads.

•The button and the button operate identically (in Program Mode) for both keypads. The words

"NEXT/YES button" are used in this manual.

•The button and the button operate identically (in Program Mode) for both keypads. The words

"PRIOR/NO button" are used in this manual.

For consistency, it is recommended that all keypads either be all "classic" or all "K Series"--both keypad

types should not be used in one alarm system.

NAPCO Security Group, Inc.,

333 Bayview Avenue, Amityville, New York 11701

For Sales and Repairs, call toll free: (800) 645-9445

For direct line to Technical Service, call toll free: (800) 645-9440

Internet: http://www.napcosecurity.com

CHANGES FROM PREVIOUS EDITION

The following changes have been made to this manual (WI818G) since the previous edition (WI818F).

New addresses added to accommodate the GEM-ACM1D / GEM-2D Access Control Accessories, as follows:

•Enable ACM Access

•ACM Zone Options

•ACM Global Flags

•ACM Timeouts

•ACM Door Area Options

•ACM Scheduled Free Access

•Enable Panel Options

•Emergency Free Access

•Keypad Home Area / ACM Door #1 Area (Hex)

•Addition to the Easy Program Menu instructions, "Enter Proximity Card Users".

Existing addresses were changed and new addresses were added to accommodate the NAPCO NetLink™ NL-Mod device, as follows:

•For each telephone number desired, enable "Report to TCP/IP Receiver or AES" for Telco 1, Telco 2 and Telco 3.

•Enable "Callback Telephone No. Select". Enter either "1" for Callback Telephone Number 1 or "2" for Callback Telephone Number 2.

•Enable "Handshake for Local Telemetry"

•Enable "TCP/IP Communications"

•Enable "TCP/IP Panel/Site Initiated Functions"

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 3

WI818G 10/05

IMPORTANT NOTE ...................................................... 2

CHANGES FROM PREVIOUS EDITION ..................... 2

SYSTEM PROGRAMMING OPTIONS ......................... 4

Introduction ............................................................... 4

Downloading from a Computer ................................. 4

EASY MENU DRIVEN PROGRAM MODE .................. 5

Dealer Program - Preliminary Information ................ 5

Accessing Dealer Program Mode ............................. 5

Customizing a Default Program ................................ 5

GEM-RP1CAe2/GEM-K1CA Keypad Easy Program

Menu ......................................................................... 6

DIRECT ADDRESS PROGRAM MODE .................... 15

Direct Address Overview ........................................ 15

Address Mode Displays .......................................... 15

Binary (Bit) Format Example .............................. 15

Decimal Format Example ................................... 16

Hexadecimal Format Example ........................... 17

Programming Conventions Used in this Manual .... 18

PROGRAMMING OPTIONS & WORKSHEETS ........ 19

SYSTEM DELAYS & TIMEOUTS (ADDRESS 0000-0002, 2402, 2406, 2414 &

3902) ............................................................................................19

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2407, 2408 & 4088) ......................19

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2400, 2401, 2403-2405, 4082 &

4083) ............................................................................................20

KEYPAD SYSTEM CODES (ADDRESS 0490-0495 & 0500-0502) .......................20

CS RECEIVER FORMAT OPTIONS (ADDRESS 0520, 0521, 0525, 0526, 0550,

0551, 0575 & 0576) ....................................................................21

CS RECEIVER TELEPHONE NUMBERS (ADDRESS 0527-0546, 0552-0571,

0577-0596) ..................................................................................22

DOWNLOAD/CALLBACK OPTIONS (ADDRESS 4089, 0600-0619, 0625-0647,

1022 & 1023) ..............................................................................22

CS SUBSCRIBER ID NUMBERS (ADDRESS 0650-0787) ....................................23

CS SUBSCRIBER ID NUMBERS (ADDRESS 0790-0857) ....................................24

CS REPORTING CODES (ADDRESS 0859-0883) .................................................24

CS REPORTING CODES (ADDRESS 0870-0904) .................................................25

CS AREA & SYSTEM REPORTING OPTIONS (ADDRESS 1024-1027) .............25

CS ZONE REPORTING CODES (ADDRESS 0910-0957) .....................................26

CS USER REPORTING CODES (ADDRESS 1030-1074) .....................................27

GLOBAL SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1082-1116)28

AREA SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1120-1137) ...29

ZONE OPTIONS / ZONES 1-16 (ADDRESS 1200-1386) .......................................30

ZONE OPTIONS / ZONES 17-32 (ADDRESS 1402-1586) .....................................31

ZONE OPTIONS / ZONES 33-48 (ADDRESS 1602-1786) .....................................32

SYSTEM OPTIONS (ADDRESS 2415-2419) ...........................................................34

SYSTEM OPTIONS (ADDRESS 2420-2422, 3874, 3905, 3880-3881) .................35

ALARM/TROUBLE REPORTING CODES (ADDRESS 3880-3881) .....................35

SYSTEM OPTIONS (ADDRESS 3882-3901, 3903-3905 & 4084) .........................36

KEYPAD OPTIONS (ADDRESS 2425-2446) ...........................................................37

ACM ZONE OPTIONS (ADDRESS 2740-2769) .......................................................38

ACM GLOBAL FLAGS (ADDRESS 2780) ................................................................38

ACM TIMEOUTS (ADDRESS 2782-2783) ................................................................38

ACM DOOR AREA OPTIONS (ADDRESS 2784-2787) ..........................................39

ACM SCHEDULED FREE ACCESS (ADDRESS 4072-4075) ...............................39

KEYPAD HOME AREA / ACM DOOR #1 AREA (HEX) (ADDRESS 2425-2431) 40

SYSTEM OPTIONS (ADDRESS 2423) .....................................................................41

EMERGENCY FREE ACCESS (ADDRESS 4080) ..................................................41

USER AREA OPTIONS (ADDRESS 2455-2502) .....................................................42

EZM GROUP OPTIONS (ADDRESS 2555-2576) ....................................................43

AREA ARMING OPTIONS (ADDRESS 2650-2651) ................................................44

REMOTE ACCESS LOGGING (ADDRESS 3184) ..................................................44

AREA OUTPUT CONTROL OPTIONS (ADDRESS 2700-2739) ...........................45

RF RECEIVERS & SUPERVISORY TIMER OPTIONS (ADDRESS 3776 & 3760-

3775) ............................................................................................ 46

EXTERNAL RELAY CONTROL / RELAYS 1-24 (ADDRESS 3778-3801 & 2800-

2895) ............................................................................................ 47

NUMBER OF RELAY BOARD MODULES (ADDRESS 3777) ...............................51

SYSTEM RESET OPTIONS (ADDRESS 4091-4093) .............................................52

USER PROGRAM MODE .......................................... 52

Preliminary Information ........................................... 52

Accessing User Program Mode ............................. 53

User Codes ............................................................ 53

Zone Descriptions .................................................. 54

KEYPAD CONFIGURATION MODE ......................... 55

Keypad Installation ................................................. 55

Configuring the Keypads ........................................ 55

ALPHABETICAL INDEX ............................................ 57

ADDRESS NUMBER INDEX ..................................... 61

GEM-P3200 WIRING DIAGRAM ............................... 68

TABLE OF CONTENTS

Refer to accompanying GEM-P3200 Installation Instructions (WI817) for installation information.

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 4 WI818G 10/05

SYSTEM PROGRAMMING OPTIONS

INTRODUCTION

The GEM-P3200 control panel may be programmed by various means, each of which will be covered in detail in the sections

that follow. Keypad displays shown are for a GEM-K1CA (v.8), the recommended keypad for programming.

Downloading From a Computer. This is the preferred method of programming. The panel may be

downloaded from (or uploaded to) an IBM PC-compatible computer, either locally or remotely. Napco's PCD3000

and PCD Windows Quickloader software feature context-sensitive help screens as well as an error-checking utility

that prevents programming of incompatible or conflicting data to ensure proper panel operation. Note: Unattended

downloading from a computer is not allowed for Fire Alarm or UL installations.

Easy Menu-Driven Program (Dealer Program) Mode - Keypad Programming. The Easy Menu-Driven

Program Mode allows keypad programming of number of zones in Area 1 and 2, number of fire zones (both 4-wire

and 2-wire), local or Central Station reporting, number of exit/entry zones, number of interior zones, number of 24

hour zones, number of chime zones, Chime 2 zones, Exit/Entry2 zones, 50ms loop response zones (Note: 750mS is

required for Loop Response time in UL installations), aux output activated on alarm zones, sensor watch zones, key-

pad sounder on alarm zones, auto bypass re-entry zones, EOLR zones, number of keypads in Area 1 and 2, Central

Station telephone number, Central Station account number, Central Station receiver format, User Codes, RF trans-

mitter points, RF keyfob transmitters, zone descriptions, date/time, dealer code, Telco line fault test, Burg output chirp

on keyfob, keypad time/date display, enable CP-01 programming, and clear dealer program/cold start. For new pan-

els, a custom default program may be created at the keypad. A menu-driven utility prompts the installer to configure

the system. Further detailed customization is accomplished in the Direct Address Program Mode.

Direct Address (Dealer Program) Program Mode - Keypad Programming. The Direct Address Pro-

gram Mode is an extension of the Dealer Program Mode wherein data is entered at the keypad by location. This

mode is accessed from the Easy Menu Driven Program Mode by pressing the C button at any time.

User Program Mode - Keypad Programming. The User Program Mode is intended for authorized users

and is limited to keypad programming of User Codes, Time, Date and Zone Descriptions.

DOWNLOADING FROM A COMPUTER

The control-panel program may be downloaded from the computer by any of the following methods.

Local Downloading

(Note: This procedure should be used after installation, after peripheral devices are connected).

For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2)

on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-

conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).

Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. Connect

JP2 on the control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer to

PCI-MINI Installation Instructions WI767).

Remote Downloading

(Also see PCI2000/3000 Installation Instructions WI443).

Function Mode

Start by establishing a telco connection between the computer operator and the installer. During this procedure,

voice contact will be lost, therefore both the installer and the computer operator should be familiar with the opera-

tion. When a steady high-pitched tone is heard at the site phone, access the “ACTIVATE DOWNLOAD” Function (see

Keypad Programming Modes), then press the J or U button or the NEXT/YES button; the site phone will go dead.

Hang up the phone and wait for a call from the central station confirming a successful download.

Callback Method

An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-Method

Download feature of the PCD-Windows Quickloader software. Remote downloading requires a modem compatible

with the PCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security

Code and, if confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel

will automatically disconnect and call the computer at this number before establishing a connection.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 5

WI818G 10/05

EASY MENU DRIVEN PROGRAM MODE

DEALER PROGRAM - PRELIMINARY INFORMATION

Only Keypad #1 may be used for both dealer and user programming, however this keypad may be located in any area.

The Master Security Code is printed on the panel’s microprocessor can. Use this code to enter the Dealer Program Mode

to program a custom Dealer Security Code. Record the number, then remove the code label to prevent unauthorized

access to the panel. If you forget your Dealer Security Code, use the Master Security Code to enter programming.

After entering codes or data, press the save U button. Data will not be stored into memory unless it is pressed.

If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.

Silence the sounder by pressing the G button to continue, or by pressing the C button to exit.

A panel that has been COLD STARTED (Address Location 4093) performs identically to a new panel.

If a GEM-RP2ASe2/GEM-K2AS (Version 6) is used, configure address jumpers as Keypad #1 (see WI1184).

KEYPAD #1: For ease of programming, it is recommended that a GEM-K1CA (Version 8) be used as Keypad #1.

(Regardless of which keypad is selected, all new keypads are configured as Keypad #1 out of the box).

NEW PANELS: The custom default program may be created for new panels only. Once the panel has been programmed by any

means, the number of areas, number of zones, fire zones, entry/exit zones and interior zones will be suppressed and cannot be

changed. Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press the C

button to enter the Direct Address Program Mode; (b) access Location 4091 (Clear Program); (c) press the U button and start over.

1. Press EEEEEE R

2. Press Q Until “ACTIVATE PROGRAM Y/N” appears on the keypad display.

3. Press P To Enter Dealer Program Mode.

4. Press CC To Exit Dealer Program Mode when finished.

Master Security Code

(on microshield)

R

GEM-P3200

CONTROL

COMMUNCIATOR

MASTER SECURITY CODE

# - # - # - # - # - #

ACCESSING DEALER PROGRAM MODE

CUSTOMIZING A DEFAULT PROGRAM

For new panels, you can design a default program that will best suit your application. Using this procedure, you will configure the panel for:

This procedure will automatically set up system keypads, EZMs, wireless transmitters, etc. After your basic default program has been

loaded, you may alter it as necessary in the Direct Address Program Mode.

•Total Number of Zones in Area 1

•Total Number of Zones in Area 2

•Fire Zones in Area 1

•2-Wire Fire Zones in Area 1

•Report All Zones to Central

•Exit/Entry Zones in Area 1

•Interior Zones in Area 1

•24 Hour Zones in Area 1

•Chime Zones in Area 1

•Chime 2 Zones in Area 1

•Exit/Entry2 Zones in Area 1

•50mS Loop Response Zones (Note: 750mS is

required for Loop Response time in UL installations).

•Aux Output Activated on Alarm Zones

•Sensor Watch Zones

•Keypad Sounder on Alarm Zones

•Auto Bypass re-entry Zones

•Enable no EOLR Zones

•Enable Telco Line Fault Test

•Enable Burg Output Chirp on Keyfob

•Enable SIA CP-01 Features

•Number of Keypads in Area 1

•Number of Keypads in Area 2

•Central Station Receiver 1 Tel. Number

•Central Station Receiver 1 Account Number

•Central Station Receiver 1 Format

•Enter User Codes

•RF Transmitter Points

•Quick Method (Enroll Method)

•KeyFob Transmitters (as Arm/Disarm & Control

Devices)

•KeyFob Transmitters (as Zone Input Devices)

•Enter Zone Descriptions

•Enter Date

•Enter Time

•Dealer Code

•Exit Dealer Program Mode

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 6 WI818G 10/05

GEM-RP1CAe2/GEM-K1CA Keypad Easy Program Menu

To create a custom program using the GEM-RP1CAe2/GEM-K1CA keypad, simply answer the following questions and re-

cord your information on the Easy Menu Programming Worksheet. In each of the following steps, press R to set cursor,

the NEXT/YES button to go forwards, the PRIOR/NO button to go backwards, U to save and C twice to exit at any time.

Total Number of Zones in Area 1 (New Program Only)

•Enter the total number of zones to be programmed for Area 1.

•Valid entries are from 08 to 48. Directly enter the total number of zones, including leading zeros.

•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically round up to

the next group of 4. For example, if you enter 18, it will automatically convert this to 20 zones. Press U to

save. Press the NEXT/YES button to proceed.

Total Number of Zones in Area 2 (New Program Only)

•Enter the total number of zones to be programmed for Area 2.

•Valid entries are from 00 to 48. Directly enter the total number of zones, including leading zeros.

•The system is based on groups of 4 zones each (after the first 8 zones), and will automatically round up to

the next group of 4. For example, if you enter 18, it will automatically convert this to 20 zones. Press U to

save. Press the NEXT/YES button to proceed.

Fire Zones in Area 1 (New Program Only)

•Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).

•Valid entries are from 01 to 48.

•Directly enter each zone number, including leading zeros, and press U to save, and then repeat for any

additional zone(s). Press the NEXT/YES button to proceed.

2-Wire Fire Zones in Area 1 (New Program Only)

•Enter the zone number of any Fire Zone (from previous question) to be used with 2-wire smoke detectors.

•Valid entries are 07 and 08. Directly enter each zone number, including leading zeros.

•Press U to save, and repeat for any additional zone(s); press NEXT to proceed.

NOTE: Only zones which have been designated as Fire Zones can be programmed as 2 Wire Fire zones.

JP3 must be set to “2-WF” position for 2-wire fire for zones 7-8. (refer to Installation Instructions).

Local or Central Station Reporting System (New Program Only)

Press the NEXT/YES button for all zones to report; press the PRIOR/NO button for local system.

Exit/Entry Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as Exit/Entry zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: Entry Delay Time of 30 seconds and Exit Delay Time of 60 seconds will automatically be programmed.

Interior Zones in Area 1 (New Program Only)

•Enter the zone numbers to be used as Interior Zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s).

•Press the NEXT/YES button to proceed.

•All Interior zones will also be automatically programmed as “Exit/Entry Follower” and as "Power Up Delay" zones.

24 Hour Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as 24 Hour zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).

Chime Zones in Area 1 (New Program Only)

•Enter the zone numbers which are to be used as Chime Zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

• Press U to save and then repeat for any additional zone(s), press the NEXT/YES button to proceed.

NOTE: A chime time of 2 seconds will be automatically programmed.

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

(Direct Entry)

#of Zns in Area1

Enter # Zones XX

(Direct Entry)

#of Zns in Area2

Enter # Zones XX

(Direct Entry)

Fire Zones

Enter Zone # °°

(Direct Entry)

2-Wire Fire Zns

Enter Zone # °°

(Press YES or NO)

Report All Zones

To Central? Y/N

(Direct Entry)

Exit/Entry Zones

Enter Zone # XX

(Direct Entry)

Interior Zones

Enter Zone # XX

(Direct Entry)

24 Hour Zones

Enter Zone # °°

(Direct Entry)

Chime Zones

Enter Zone # °°

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 7

WI818G 10/05

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

Chime 2 Zones in Area 1 (New Program Only)

•Enter the zone numbers which are to be used as Chime 2 Zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

NOTE: A chime time of 2 seconds will be automatically programmed.

Chime 2 zones give a distinct pulsating tone when zone is faulted.

Exit/Entry2 Zones in Area 1 (New Program Only)

•Enter the zone numbers of zones to be used as Exit/Entry zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and repeat for any additional zone(s); press the NEXT/YES button to proceed.

NOTE: An Entry Delay Time of 30 sec. and an Exit Delay Time of 60 sec. will automatically be programmed.

50 mS Loop Response Zones (New Program Only)

•Enter the zone numbers of zones to have a 50mS loop response.

•Valid entries are from 01 to 08. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed. Note: Only

panel zones 01-08 can be programmed for Quick Loop Response. All other zones can be programmed via their

respective EZM's (hardwire). Note: 750mS is required for Loop Response time in UL installations.

Aux Output Activated on Alarm Zones (New Program Only)

•Enter the zone numbers of zones to activate the Aux Output upon alarm.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

NOTE: An Aux Output Timeout of 15 minutes will automatically be programmed.

Sensor Watch Zones (New Program Only)

•Enter the zone numbers of zones to be Sensor Watch zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

NOTE: A Sensor Watch Time of 24 hours will automatically be programmed.

Keypad Sounder On Alarm Zones (New Program Only)

•Enter the zone numbers of all zones to activate the Keypad Sounder upon alarm.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

Auto Bypass Re-entry Zones (New Program Only) (Not evaluated by UL)

•Enter the zone numbers of zones to be Auto Bypass Re-entry zones.

•Valid entries are from 01 to 48. Directly enter each zone number, including leading zeros.

•Press U to save and then repeat for any additional zone(s), Press the NEXT/YES button to proceed.

•Auto Bypass Re-entry Zones allow the system to be armed with the zone faulted but come back into the system

(armed) when the zone is subsequently closed.

Enable No EOLR Zones (New Program Only)

•Press YES to program all zones except 24 Hr & fire zones for No End Of Line Resistor. Press NO to continue.

•Do not program this feature for UL Installations.

Enable Telco Line Fault Test?

•Press YES to enable Telco Line Fault Test.

•Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will automatically be pro-

grammed.

Enable Burg Output Chirp on KeyFob?

•Press the NEXT/YES button to enable Burg Output Chirp on KeyFob Arm / Disarm.

•Press the PRIOR/NO button to continue.

NOTE: The Burg Output will chirp once on Keyfob Arm and twice on Keyfob Disarm.

(Direct Entry)

Chime 2 Zones

Enter Zone # °°

(Direct Entry)

Exit/Entry2 Zones

Enter Zone # °°

(Direct Entry)

50mS Loop Zones

Enter Zone # °°

(Direct Entry)

Aux Output Zones

Enter Zone # °°

(Direct Entry)

Sensor Watch Zns

Enter Zone # °°

(Direct Entry)

KP Sndr Alrm Zns

Enter Zone # °°

(Direct Entry)

Auto Byp REnt Zn

Enter Zone # °°

(Press YES or NO)

Enable No EOLR

Zones Y/N

(Press YES or NO)

Enable Telco

Line Test? Y/N

(Press YES or NO)

Enable Burg Out

Chirp? Y/N

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 8 WI818G 10/05

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

Enable SIA CP-01 Features?

•Press the NEXT/YES button to enable.

•Press the PRIOR/NO button to continue.

The SIA CP-01 Features are designed to reduce the incidence of false alarms. NOTE: Do not enable

unless reporting, otherwise system trouble Fail to Communicate may occur.

Number of Keypads in Area 1

•Enter the total number of Keypads to be installed in Area 1.

•Valid entries are from 01 to 07. Directly enter the number of keypads, including leading zeros.

Press U to save. Press the NEXT/YES button to proceed.

Number of Keypads in Area 2

•Enter the total number of Keypads to be installed in Area 2.

•Valid entries are from 00 to 07. Directly enter the number of keypads, including leading zeros.

Press U to save. Press the NEXT/YES button to proceed. NOTE: Area 2 keypads must have zones in

Area 2, otherwise the keypad will indicate "Out Of System".

Central Station Receiver 1 Telephone Number

•Enter telephone number of up to 16 digits.

•Press 1 through 9 for digits 1–9; G 0 for a zero and 0 for a blank (•).

•Press G 1 through G 5 for letters B–F, respectively.

•Pre-Dial Delay = “D” (G 4); Dial-Tone Detection = “E” (G 5).

•Press U to save and press the NEXT/YES button to proceed.

NOTE: Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Address Program-

ming. See CS Receiver Options.

(Direct Entry)

Central Phone #

(Direct Entry)

# Area 1 Keypads

Enter # KPs 01

(Press YES or NO)

Enable SIA CP-01?

Y/N

(Direct Entry)

# Area 2 Keypads

Enter # KPs 00

Easy Programming of Auto download ID #'s and PC Preset Callback Numbers (GEM-RP1CAe2 or GEM-K1CA

keypads only) from the Central Station Telephone number.

For unattended PC Preset downloading, it is now possible to set the Auto download ID #’s and PC Preset Callback

from the Keypad Easy Program Mode.

•At the field for CENTRAL PHONE #, program an "F" followed by the Auto Download ID # (2 digits) and then the

Callback Telco # (up to 13 digits).

•Press D or U to save.

•Exit Program Mode (CC)

•Enter Master Code

•Press A or R

•Go to Function "ACTIVATE DOWNLOAD Y/N" and press YES (E or P).

•The panel will automatically call the PC Preset computer and download the program on the specified Auto

Download line # of PC Preset. Example: Program an Auto download ID # of 07 and a PC Preset Callback # of

1-516-842-9400

• Go to Central Phone # input screen and press: [*] [5] [0] [7] [1] [5] [1] [6] [8] [4] [2] [9] [4] [0] [0] D (or U).

CENTRAL PHONE #

F0715168429400

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 9

WI818G 10/05

Central Station Receiver 1 Account Number

•Enter an account number of up to four digits.

•Press 0 through 9 for digits 0–9, and G 0 for a blank (•).

•Press U to save and press the NEXT/YES button to proceed.

NOTE: Central Station Receiver 2 and 3 Account Numbers must be entered in Direct Address Pro-

gramming. See CS Reporting Options.

Central Station Receiver 1 Format

•From the table at the right enter the receiver format.

•Press 0 through 9, and G0 for blank (•).

•Press G1 through G4 for letters B–E.

•Press U to save and press the NEXT/YES button to proceed.

(Direct Entry)

Central Station

Account # (____)

(Direct Entry)

See WI for Info

Rcvr Format (0)

DATA

ENTRY

CS RECEIVER 1 FORMAT

blank(•) Ademco Slow, Silent Knight Slow

1 Sescoa, Vertex, DCI, Franklin

Fast

2 Radionics Fast

3 Silent Knight Fast

4 Radionics, DCI, Franklin Slow

5 Universal High Speed

8 Radionics BFSK

DATA

ENTRY

CS RECEIVER 1 FORMAT

9 FBI 4/3/1

0 Radionics Modem 2

B SIA

C Ademco Point ID

D Ademco Express

E Pager

NOTE: Modem IIe is available only in

Direct Address Programming. Central

Station Receiver 2 and 3 Formats can

only be entered in Direct Address

Programming. See CS Receiver

Options.

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 10 WI818G 10/05

Enter User Codes (Press the R button to set cursor.)

Enter up to 48 User Codes with User Options, Authority Level and Access

Control Options (if necessary) for each code. Refer to the tables below and on

the next page for available data entries for User Options, Authority Level and

Access Control Options. Note: All 48 Users must be assigned to areas in “User

Area Options” (Address 2455-2502) in Direct Address Programming. By de-

fault, only User 1 is enabled in Area 1 and Area 2. Users 2 - 8 are enabled in

Area 1 and users 9 - 16 are enabled in Area 2.

Press the R button to set the cursor to the User Code. Use the number buttons 1 through 9 to enter

a code from 3 to 6 digits. Enter up to 6 digits in the first six boxes from left to right for each user code. Valid entries

are: 0-9. Note: Press the 0 button for a zero. No blank spaces in between; leave blank (•) any trailing boxes. If

an “Ambush Code” (Address 0495) is entered, do not program the first two digits of ANY User Code as the same

digits entered for the “Ambush Code”.

If the programmed code is less than 6 digits, press the R button to set the cursor to the OPTION/LEVEL.

 Refer to the tables below for the available User Option and User Level data entries. Enter the user options data in

the left digit. Enter the level data (with arming options, if any, added) in the right digit. Note: For entries greater than

9, press the G1 buttons through the G5 buttons for B through F, respectively.

For Keypad Access Control, press the R button once again to program applicable keypads. Refer to the tables

below, use the number buttons to enter the data for Keypad 1–4 in the right digit; and the data for Keypad 5–7 data in

the left digit. (Press the 0 buttons for blank).

Enter user code

001 123 -E3-

User# User Code

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

USER OPTIONS

USER CODE

(UP TO 6 DIGITS)

USER

OPTION

USER

LEVEL

ACCESS CONTROL

KEYPADS

DATA

ENTRIES

AUTHORITY

LEVEL

CODE

TYPE

blank (•) NONE ARM/DISARM

1 LEVEL 1 ARM/DISARM

2 LEVEL 2 ARM/DISARM

3 LEVEL 3 ARM/DISARM

4 NONE ARM ONLY

5 LEVEL 1 ARM ONLY

6 LEVEL 2 ARM ONLY

7 LEVEL 3 ARM ONLY

8 NONE SERVICE

9 LEVEL 1 SERVICE

0 LEVEL 2 SERVICE

B LEVEL 3 SERVICE

C* NONE AMBUSH

D* LEVEL 1 AMBUSH

E* LEVEL 2 AMBUSH

F* LEVEL 3 AMBUSH

Note: “Y” indicates option is enabled.

USER OPTIONS

DATA

ENTRIES

BLOCKED

VIEW

USER

PROGRAM

BYPASS OVERVIEW

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

DISABLED

Note: “Y” indicates option is enabled.

ACCESS CONTROL KEYPADS

DATA

ENTRIES

K.P. 1 K.P. 2 K.P. 3 K.P. 4

blank (•)

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8 Y

9 Y Y

0 Y Y

B Y Y Y

C Y Y

D Y Y Y

E Y Y Y

F Y Y Y Y

NONE

Example: Enter a code of “123456” as

“123456” (from left to right).

Note: “Y” indicates option is enabled.

ACCESS CONTROL KEYPADS

DATA

ENTRIES

K.P. 5 K.P. 6 K.P. 7

blank (•) NONE

1 Y

2 Y

3 Y Y

4 Y

5 Y Y

6 Y Y

7 Y Y Y

8

9 Y

0 Y

B Y Y

C Y

D Y Y

E Y Y

F Y Y Y

*Note: These entries are only

available when address 3905

option 8 is enabled.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 11

WI818G 10/05

Press U to save each code.

To proceed to the next User Code, set the cursor to the User Number and change it using the number buttons. Program

a new User Code as previously described. Press NEXT P button to proceed.

Example: Program a code of “2222” for user 02, with User Option of “User Program”, User “Level 3” and Access Control Option

“Keypad No. 1”. Enter “2222” for a user code, “2 3” for user option and “blank(•) 1” for access control option.

CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described

above and press U to save. Similarly, to cancel a code, blank out each number of the code and press U to save to

save.

USER AUTHORITY LEVEL

FUNCTION LEVEL*

DISPLAY ZN FAULTS 1

DISPLAY ZN BYPASSED 1

DISPLAY ZN DIRECTORY 1

ACTIVATE BELL TEST 1

DISPLAY PHONE #’S 1

DISPLAY SYS TRBL 1

DISPLAY FIRE ALARM 1

DISPLAY FIRE TRBL 1

DISPLAY OP/CL 3

ACTIVATE OVERVIEW 3**

ACTIVATE CHIME 1

ACTIVATE WATCH 2

RESET SYSTEM TRBL 3

RESET SENSOR MSG 3

START EXIT TIME 1

FAULT FIND ***

ACTIVATE LOCATE ***

EZM ZONE FIND ***

ACTIVATE DIALER TEST 3

DISPLAY ALARM LOG 3

DISPLAY TOTAL LOG 3

DISPLAY FIRE LOG 3

DISPLAY OP/CL LOG 3

DISPLAY SYSTEM LOG 3

AUTOARM IN 1-4HRS 2

DISPLAY AUTOARM SCHD 3

ACTIVATE PROGRAM 3**

ACTIVATE DOWNLOAD 3

DISPLY RF XMITTER STAT 1

RELAY CONTROL 1

KEYPAD DISPLAY FUNCTION MENU NOTES:

* Minimum Level required to access function

** Level-3 Code with appropriate user option

*** Requires Dealer Code

Related User Options: “Ambush Code” (Address 0495), “Panel Access Code” (Address

0490), “Dealer Security Code” (Address 0500) & “User Area Options” (Address 2455-2502).

OPTIONS EXPLANATION

Disabled User Code not active in this area.

Blocked View Allows User Code to block another code from being viewed by another user.

An unblocked code cannot view a blocked code, but a blocked code can

view all codes. The master user code and the dealer program code can view

all codes.

User Program User Program Option is enabled for Keypad 1 only, wherever it is connected

(any area). If enabled, Level 3 must also be enabled.

Bypass Allows User Code to bypass zones.

Overview This option, along with Level 3 Authorization, enables selection of

OVERVIEW mode at a keypad. This Mode provides a system status display

of all areas at a glance.

Arm Only Prevents User Code from disarming this area.

Service A Service Code has restricted arm/disarm rights; if an area is armed with a

Service Code, a “5” appears on the GEM-RP1CAe2 keypad and the area can

be disarmed with any valid User Code, including a Service Code. If the area

is armed with OTHER than a Service Code, it CANNOT be disarmed with a

Service Code. This is typically used to allow tradesmen access to premises

under control of the owner.

Access This is normally used to activate a door striker while an area is disarmed. A

code with the access option will not function as an arm/disarm code. When

the code is entered, the keypad will display “ENTER NOW” and the Brown

Wire on the keypad will become Active Low (Ground Potential) for 7

seconds.

USER OPTIONS

Ambush There are two types of Ambush Codes: (1) A 2-digit code (prefix) that is entered

immediately prior to (and as part of) the regular User Code and (2) A separate

and unique User Code. Disarming with an Ambush Code will cause a silent

report to be sent to a central station. Thus, should a user be forced to disarm, he

can silently signal an emergency while appearing to be merely disarming the

system.

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 12 WI818G 10/05

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

Enter Proximity Card Users (FOR ACM USE ONLY).

(Press the R button to set cursor). See WI1221 for more information.

Enter up to 48 Proximity Cards with User Options, Access Level and ACM

Area (if necessary) for each card. Refer to the tables below and to WI1221 for

more information.

 Press the R button to set the cursor to the User Code. Use the

number buttons 1 through 9 to enter a 6 digit code. Enter the digits in the first six boxes from left to right

for each user code. Valid entries are: 0-9. Note: Press the 0 button for a zero. No blank spaces in between;

leave blank (•) any trailing boxes.

 Refer to the tables below and WI1221 for the available User Level data entries. Enter the level data in the right

digit. Leave blank (•) in the left digit. Note: For entries greater than 9, press the G1 buttons through the

G5 buttons for B through F, respectively.

For ACM Area, enter data for Areas 1 or 2. See table below.

Enter user code

001 123456- 6-

User# User Code

USER OPTIONS

USER CODE

(UP TO 6 DIGITS)

USER

LEVEL

ACM AREA

DATA

ENTRIES

ACCESS

LEVEL

CODE

TYPE

blank (•) 0 NONE

1 1 NONE

2 2 NONE

4 0 ARM/DISARM

5 1 ARM/DISARM

6 2 ARM/DISARM

8 0 ARM ONLY

9 1 ARM ONLY

0 2 ARM ONLY

Note: “Y” indicates option is enabled.

ACM AREA

DATA

ENTRIES

A1 A2

blank (•) NONE

1 Y

2 Y

3 Y Y

Example: Enter a code of “123456”

as “123456” (from left to right).

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 13

WI818G 10/05

RF Transmitter Points (Press R to set cursor.)

For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)

•The zone number (01–48) to which the transmitter will be mapped.

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The point number (1–2); enter “9” for unsupervised (all points).

•Press U to save and NEXT/YES button to proceed when all transmitters have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0 through 9; A = G0 ; B = G1 ; C =

G2 ; D = G3 ; E = G4 and “F” = G5.

Quick Method (Enroll Method). If a receiver is already installed in the panel, transmitter wireless points can be programmed automatically

(“enrolled”) using the following procedure. NOTE: The transmitter point will be enrolled only if the signal

strength is 3 or greater.

1. Enter the zone number to which the transmitter point will be mapped.

2. Press B to enter the Enroll Mode. The red and green LEDs on the keypad will

flash and the window will display as shown at left.

3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).

4. Install the transmitter battery. The keypad will beep to indicate that the point has been

successfully enrolled. Multi-point transmitters can be mapped to successive zones

simultaneously.

Keyfob Transmitters as Arm/Disarm & Control Devices (Press R to set cursor).

Keyfobs can be programmed as “Arm/Disarm” devices using their On/Off buttons (refer to WI752).

For each Keyfob Transmitter, enter:

•The Keyfob Transmitter number (01–08).

•The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The Aux 1 Option (see keyfob aux 1 & aux 2 options).

•The Aux 2 Option (see keyfob aux 1 & aux 2 options).

•NOTE: Keyfobs 1-8 report openings and closings as Users 25-32.

•Press U to save and NEXT/YES button to proceed when all keyfobs have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0 through 9 ; A = G0 ; B = G1 ;

C = G2 ; D = G3 ; E = G4 and “F” = G5.

ZN# XMIT#+CS P

Zn01- 000000:0-0

Zone # Xmitter Check Point

Mapped to ID Sum #

ZN# XMIT#+CS P

Zn01- 000000:0-0

ZN# XMIT#+CS P

ZN01- ENROLL:A--

Example. A 2-point transmitter has the RF ID number 287613:1. Map point

1 to Zone 6 and point 2 to Zone 9.

1. Enter the Enroll mode as described above.

2. Enter Zone “06”.

3. Open point-1 loop.

4. Install the battery. The keypad will beep once to indicate that one point

has been programmed. (Transmitter 287613:1, point 1 will be mapped

to Zone 6).

5. Enter Zone “09”.

6. Close point-1 loop and open point-2 loop.

7. Remove the transmitter battery, then re-install it. The keypad will beep

once to indicate that one point has been programmed. (Transmitter

287613:1, point 2 is mapped to Zone 9).

KEYFOB ZONE ASSIGNMENT: Keyfobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm sys-

tem, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the keyfob,

the location where the person holding the keyfob is stationed, or the special purpose of the keyfob button being depressed. See the

next page on Keyfob Transmitters as Zone Input Devices .

KF A XMIT#+CS OP

01-0 000000:0 00

KF Area Xmitter Check Aux

# ID Sum 1&2

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 14 WI818G 10/05

KeyFob Transmitters as Zone Input Devices

(Refer to display above: press the PRIOR button to go backwards).

Each of the 4 keyfob buttons can be assigned to a zone. For example, On button = point 1; Off button = point

2; A1 = point 3; A2 = point 4. Up to 48 keyfobs (using 1 button) or 24 keyfobs (using 2 buttons) or 14 keyfobs

(using all 4 buttons) or any combination up to a maximum of 48 controlled zones can be assigned, providing

multiple wireless panic buttons on a system, each reporting to a Central Station or a pager and/or annunciating

on a keypad the keyfob zone number with a description. To assign a keyfob to a zone: program the keyfob as

you would a transmitter, entering the keyfob's ID code, check sum and point number at the appropriate zone.

The “Quick Method” is not allowed. The zone may be hardwired to an electrical sensor as well as assigned to

a keyfob (either one will activate the zone alarm output). NOTE: If assigning a keyfob to a zone, the “ON/OFF”

buttons on the keyfob will no longer arm/disarm the system. The keyfob is converted to a “panic only” device.

Enter Zone Descriptions

•Press 1 and 2 to place the cursor and; press

3 and 6 to select the character.

•For each zone, enter a description of up to two lines.

•Press U to save each description.

•To proceed to the next description, place the cursor under the Zone Number (e.g. “01”) and change the Zone

Number using 3 and 6. Program new description as above.

•NOTE: Zone Descriptions can only be entered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader Software. See Easy

Menu Programming Worksheet for available zone description characters.

Enter Date (Press R to set cursor).

•Enter the current date in the format MM/DD/YY. (MM = month, DD = day and YY = year.

•Press U to save. Press the NEXT/YES button to proceed.

Enter Time (Press R to set cursor.)

•Enter the current time in format HH:MMA/P, where HH=hours (01–12); MM=minutes (00–59).

•Select AM or PM by pressing any number button to toggle selection.

•Press U to save. Press the NEXT/YES button to proceed.

Dealer Code

•Directly enter the Dealer Code (default = 456789), using 0 through 9 buttons.

•Press U to save.

•Re-enter the Dealer Code to verify the previous code.

•Press U to save.

•Press the NEXT/YES button to proceed.

(Direct Entry)

Enter Date

( / / )

(Direct Entry)

Enter Time

( : )

Dealer Code

456789

DEALER CODE

RE-ENTER

CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press C to enter

the Address Program Mode; (b) access Location 4091 (Clear Program) or 4093 (Cold Start); (c) press U and then (d) press C to exit the

Dealer Program Mode. A “SYSTEM TROUBLE/E09-00 SERVICE” will occur. Press C to silence the keypad.

Clear Dealer Program (Erases Dealer Program)

Use this feature to erase the Panel Program, while maintaining Scheduled Data and Zone Descriptions. Access

address 4091 and press U. Data entry is not allowed. NOTE: Enter Easy Menu Driven Program Mode

to reprogram system.

Cold Start (Erases Entire Program)

This erases all programmed data (Dealer Program, Zone Description Data and Schedules). Access ad-

dress 4093 and press U. Data entry is not allowed. NOTE: Some features (schedules) can only be pro-

grammed again with the Downloading Software.

(Direct Entry)

001-

EXIT DEALER PROGRAM MODE: This completes the custom default program. Press C to enter the Direct Address Program

Mode for further programming or press C once again to end all programming and resume normal keypad operation.

4091 XX H

4093 XX H

DATA

ENTRY

AUX 1/AUX 2 OPTIONS

0 None

1 Relay Group 1 Toggle

2 Relay Group 2 Toggle

9 Panic

A Auxiliary

B Instant

C Aux. Output Toggle

D Access on Aux. Output

E Arm STAY ("K Series"

Keypads Only)

F Interior Bypass

("Classic" RP Series

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 15

WI818G 10/05

DIRECT ADDRESS OVERVIEW

Direct Address Programming allows you to go directly to the address locations (up to 4095) and change the data entries

manually in order to customize your control panel options. Whereas the Easy Menu Program Mode guides you through

limited selections to get you started, Direct Address Program Mode allows you to change all options directly. It con-

sists of up to 4095 address locations each with data entry locations as shown in the following diagram (below left). The

data entry location accepts data in one of three formats: Binary, Decimal and Hexadecimal (explained below in

"Address Mode Displays"). The following diagram (below right) illustrates a Decimal format data entry location (using

a GEM-RP1CAe2/GEM-K1CA keypad).

ADDRESS MODE DISPLAYS

There are three types of address displays when programming in Direct Entry Program Mode, as follows:

A) Binary (Bit) Format

Settings (such as Zone Features) display and accept data in "number" format. For example, Zone Features are

turned on by the pressing of keypad buttons 1 through 8, with the activated Zone(s) displaying the corresponding

decimal digit (replacing deactivated zones which are signified by dashes).

EXAMPLE: BIT Format with the GEM-RP1CAe2/GEM-K1CA: Program Zones 2, 4, 5 and 7 as Exit/Entry Fol-

lower Zones.

DETERMINE THE DATA ENTRIES

Referring to ZONE FEATURES in the Programming Worksheets that follow, the Exit/Entry Follower for Zones 1

through 8 are located at address 1218.

DATA ENTRY

LOCATION

ADDRESS

LOCATIONS

0000

TO

4095

DATA ENTRY LOCATION:

(One of three formats):

•Binary (Bit)

•Decimal

•Hexadecimal

DIRECT ADDRESS PROGRAM MODE

GEM-RP1CAe2/GEM-K1CA Keypad Display

Example

0000 060 D

1 2

= ADDRESS LOCATION

1

2 = DATA ENTRY LOCATION

1218 - - - - - - - - B 1218 - 2 - 4 5 - 7 - B

DATA ENTRY LOCATION:

Binary (Bit) Format

Press 2 4 5 and 7 in

order to activate Zones 2, 4, 5, and 7. (The "B"

on the right indicates "Binary" format).

DATA ENTRY LOCATION:

Binary (Bit) Format

•No zones yet activated

Address

1218

"Exit/Entry

Follower"

Address

1218

"Exit/Entry

Follower"

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 16 WI818G 10/05

PROGRAM THE DATA ENTRIES

1. Enter the panel's Dealer Security Code, then press R.

2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass

“ACTIVATE PROGRAM”, scroll backward using B.

3. Press C to enter the Address Program Mode. Address "0000" will display.

4. Press 1218 to access Address 1218. The existing data will display and the cursor will

advance to the data field.

5. Press 6 7 8. The numbers 6,7 and 8 will appear on the keypad display indicating the zones

activated.

6. Press U to save. Address 1218 is now programmed with “6,7,8”.

7. Press R and enter another 4-digit address to continue programming--or--press C to exit and resume

normal keypad operation.

B) Decimal Format

Settings (such as Entry and Exit Delay) display and accept data in decimal format, as a 3 digit number. Data is en-

tered directly, by pressing keys 0 – 9, with the cursor automatically moving to the right upon each key press.

EXAMPLE: DECIMAL Format with the GEM-RP1CAe2/GEM-K1CA: Program Abort Delay to be 15 seconds.

DETERMINE THE DATA ENTRIES

Referring to SYSTEM DELAYS & TIMEOUTS in the Programming Worksheets that follow, the Abort Delay is lo-

cated at address 2406:

PROGRAM THE DATA ENTRIES

1. Enter the panel's Dealer Security Code, then press R.

2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass

“ACTIVATE PROGRAM”, scroll backward using B.

3. Press C to enter the Address Program Mode. Address "0000" will display.

4. Press 2406 to access Address 2406. The existing data will display and the cursor will

DIRECT ADDRESS PROGRAM MODE

2406 - - - D 2406 015 D

ZONES 1  8 ZONES 9  16

ZONE FEATURES ADDR Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 ADDR Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

Exit/Entry Follower 1218

6 7 8

1318

DATA ENTRY LOCATION:

Decimal Format

•No time yet entered

Address

2406

"Abort

Delay"

DATA ENTRY LOCATION:

Decimal Format

Press 0 1 5 in order to set

"Abort Delay" to 15 seconds. The "D" on the

right indicates "Decimal" format.

ABORT ADDRESS 2406

DELAY

(sec.)

[Default = 000]

Address

2406

"Abort

Delay"

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 17

WI818G 10/05

DIRECT ADDRESS PROGRAM MODE

advance to the data field.

5. Press 015. The numbers 015 will appear on the keypad display indicating the number of

seconds entered.

6. Press U to save. Address 2406 is now programmed with a 15-second Abort Delay.

7. Enter another 4-digit address to continue programming or press C to exit and resume normal keypad

operation.

C) Hexadecimal Format

Data such as Report Codes displays, accepts data by means of a Hexadecimal display. Data is entered directly, by

pressing keys 1 – 9, G0 for zero, and G 1 through G 5 for hex B through F (11-15), with the

cursor automatically moving to the right upon key press. See table below.

EXAMPLE: HEXADECIMAL Format with the GEM-RP1CAe2/GEM-K1CA: Program an Ambush CS Reporting Code to be

"1B".

DETERMINE THE DATA ENTRIES

Referring to CS REPORTING CODES in the Programming Worksheets that follow, Ambush is located at address

0900. In the "Keypad Reporting Codes" table, the data entries needed to assign a code of "1B" are "1"

and "G1".

ENTRY

TOTAL

PRESS

N KEYPAD

DISPLAYS

ENTRY

TOTAL

PRESS

N KEYPAD

DISPLAYS

blank 0 • 8 8 8

1 1 1 9 9 9

2 2 2 10 G 0 0

3 3 3 11 G 1 B

4 4 4 12 G 2 C

5 5 5 13 G 3 D

6 6 6 14 G 4 E

7 7 7 15 G 5 F

HEXADECIMAL ENTRIES

DATA ENTRY LOCATION:

Hex Format

•No data yet entered

DATA ENTRY LOCATION:

Hex Format

Press 1G1 in order to set

"Ambush" Reporting code to "1B". The "H"

on the right indicates "Hexadecimal" format.

Address

0900

"Ambush"

0900 - - H 0900 1 B H

Address

0900

"Ambush"

LEFT ADDR RIGHT

1 0900 B

0901

0902

0903

0904

ADDRESS

0900-0904

KEYPAD REPORTING

CODES

Ambush

Panic

Fire

Auxiliary

Tamper

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 18 WI818G 10/05

DIRECT ADDRESS PROGRAM MODE

PROGRAM THE DATA ENTRIES

1. Enter the panel's Dealer Security Code, then press R.

2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass “ACTIVATE

PROGRAM”, scroll backward using B.

3. Press C to enter the Address Program Mode. Address "0000" will display.

4. Press 0900 to access Address 0900. The existing data will display and the cursor will ad-

vance to the data field.

5. Since you wish the reporting code to be "1B", press 1 to enter a "1" in the display, and press

G1 to enter a "B" in the display. NOTE: The right address is reported first, therefore, in the ad-

dress table, the right digit is the 1st digit of the reporting code ("1" in this example).

6. Press U to save. Address 0900 is now programmed with an Ambush reporting code of "1B".

7. Press R and enter another 4-digit address to continue programming--or--press C to exit and resume

normal keypad operation.

PROGRAMMING CONVENTIONS USED IN THIS MANUAL

The Keypad Programming Worksheets that follow are provided as an address-programming reference to help the in-

staller modify his custom default program or to make minor field alterations to an existing panel program. It is recom-

mended that the panel be uploaded to NAPCO's PCD-Windows software following any keypad programming and that

the PCD-Windows's error-check feature be utilized to reduce the possibility of programming omissions or conflicts.

3

Keep the Keypad Programming Worksheets on file for future reference.

General Programming Steps

1. Contact the central station to ascertain receiver format, data format, event codes, subscriber numbers and tele-

phone number(s).

2. Select the desired features by writing in (pencil recommended) the respective “address” boxes. Refer to the

Programming Options and Worksheets for guidance in selecting the “data” to be entered into those boxes.

3. Program the data entered in the boxes on the worksheets into the respective addresses. The display will show

the entry numerically, but if hexadecimal format will display “0” for the number 10, and letters “B”, “C”, “D”, “E”, and

“F” for the numbers 11 through 15, respectively. To program a 10, press G 0. To program 11 through

15, press G 1 through G 5, respectively.

The displays will appear after a brief delay.

Use R to toggle the cursor between the 4-digit address field and the data entry locations.

Enter the address directly using the number buttons.

The contents of the address will be read automatically, along with the feature name and programming information.

The cursor will advance to the data field. Enter the required data directly using the number buttons.

IMPORTANT: Press U or D to save the contents of each address.

EXIT DIRECT ADDRESS PROGRAM MODE: When done, press C to exit and resume normal keypad operation.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 19

WI818G 10/05

SYSTEM DELAYS & TIMEOUTS (ADDRESS 0000-0002, 2402, 2406, 2414 & 3902)

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2407, 2408 & 4088)

SYSTEM DELAYS/TIMEOUTS

EXIT ADDRESS 0000

DELAY

(sec.)

[Default = 060]

ADDRESS 0001

[Default = 030]

ENTRY

DELAY 1

(sec.)

ADDRESS 0002

[Default = 030]

ENTRY

DELAY 2

(sec.)

ADDRESS 2402

[Default = 000]

Aux.

Output

Access

Control

Timeout

(sec.)

ADDRESS 2406

[Default = 000]

ABORT

DELAY

(sec.)

ADDRESS 2414

[Default = 000]

Telephone

Line Test

Delay

(x15 sec.)

ADDRESS 3902

[Default = 000]

CS Telco 3

Report

Delay

(sec.)

WARNING: Timers have uncertainty of +/-1 sec, so a "time" of 1 second may actually timeout IMMEDIATELY.

 Select delay/timeout (0-255 seconds).

EXIT/ENTRY DELAYS: Apply only to zones programmed with the following options “Exit/Entry 1, Exit/Entry

2, Exit/Entry Follower”. For UL Installations, the maximum exit delay is 60 seconds and the maximum entry

delay is 45 seconds. NOTE: Sensor Watch Time Options are similar to above table, except in hours.

 Press U or D to save.

1. Enter delay/timeout in corresponding address locations above.

Note: All entries for address 2407 are in quarter seconds (.25 seconds).

Therefore, the default of 008 results in a 2 second timeout.

2. Press U or D to save.

CHIME ADDRESS 2407

TIME

(¼sec.)

[Default = 008 x ¼ sec. = 2 sec.]

AC Fail ADDRESS 2408

Report Delay

(x10 min.)

[Default = 008]

ADDRESS 4088

[Default = 024]

Sensor Watch

Delay (Hr.)

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 20 WI818G 10/05

[Default = blank (•) blank (•) from address 0490-0492]

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2400, 2401, 2403-2405, 4082 & 4083)

KEYPAD SYSTEM CODES (ADDRESS 0490-0495 & 0500-0502)

DEALER SECURITY CODE: Enter up to 6 digits to be used by the dealer to enter programming.

1. Enter in both left and right digits of address locations.

2. Valid entries are: 0-9.

Note: If left blank, the Master Security Code must then be used to enter programming.

AMBUSH CODE: Enter a 2-digit code used just prior to disarming and will activate an Ambush Condition, causing a SILENT report to

be sent to the central station.

1. Enter in both left and right digits of address locations.

2. Valid entries are: 0-9.

Note: Also, “Enable Keypad Ambush” (Address 2440-2446), “Report on Ambush Alarm” (Address 1125, 1127, 1135 & 1137) must be

enabled and “Ambush Reporting Code” (Address 0900) must be provided.

Panel Access

Code

ADDRESS 0490-0492

0490 0491

L R L R L R

0492

PANEL ACCESS CODE: Enter up to 6 digits to activate a door strike while the area is disarmed.

1. Enter in both left and right digits of address locations.

2. Valid entries are: 0-9.

Note: Also, “Access Control on Aux. Output” (Address 2418) and “Aux. Output Access Control Timeout” (Address 2402) must both

be enabled.

LEFT RIGHT

ADDRESS 0495

Ambush

Code

[Default = 99]

[Default = blank (•) blank (•) from address 0500-0502]

Dealer Security

Code

ADDRESS 0500-0502

0500 0501

L R L R L R

0502

SYSTEM DELAYS/TIMEOUTS & KEYPAD CODES

ADDRESS 2400

[Default = 000]

Reset Output

Timeout

(min.)

1. Select delay/timeout (0-255 min.).

2. Enter in corresponding address locations above and right.

3. Press U or D to save.

OUTPUT TIMEOUTS: If a timeout of “0 min.” is selected, then the output will

remain active (ON) until the system is reset or disarmed. For UL Residential In-

stallations, the minimum timeout is 4 minutes. For UL Commercial Installations,

the minimum timeout is 15 minutes.

ADDRESS 2401

[Default = 000]

Aux. Output

Timeout

(min.)

ADDRESS 2403

[Default = 015]

Burg. Alarm

Output

Timeout

(min.)

ADDRESS 2404

[Default = 015]

Pulse Alarm

Output

Timeout

(min.)

ADDRESS 2405

[Default = 000]

Fire Output

Timeout

(min.)

ADDRESS 4082

[Default = 000]

V.1 or less = sec.

V.3 or greater = min.

Program for at least 5 minutes

in a CP-01 installation.*

Report

Cancel

Window

(min or sec.)

ADDRESS 4083

[Default = 000]

Auto Disarm

Rearm Delay

(min.)

*Address 4082: When "Enable CP-01 Features" is selected

in the Easy Program menu, this time is set to 7 minutes.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 21

WI818G 10/05

ADDRESS 0525

CS Receiver 1

Format

ADDRESS 0550

CS Receiver 2

Format

Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR FORMAT”. [Default = •(blank) E] for CS Receivers 1, 2 and 3 Formats.

CS RECEIVER FORMAT OPTIONS (ADDRESS 0520, 0521, 0525, 0526, 0550, 0551, 0575 & 0576)

CS RECEIVER FORMATS: Up to 3 CS Formats may be programmed.

1. Select the desired CS Receiver Format from the table shown.

2. Enter in the corresponding digit address locations for each CS

Receiver.

NOTE: Dark shaded data value box shows option not available.

Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR

FORMAT”. [Default = •(blank) E] for CS Receivers 2 and 3 Formats.

CS RECEIVER FORMATS: Up to 3 CS Formats may be pro-

grammed.

1. Select the desired CS Receiver Format from the table shown.

2. Enter the corresponding digit in the address location for each CS

Receiver. NOTE: Dark shaded data value box shows option not

available. Press [Enter] of [ON/OFF] to save.

NOTES:

* If both are selected, 1400Hz has priority over 2300Hz.

** For NAPCO NetLink™ installations only: For each telephone num-

ber desired, enable to allow the panel to report alarms via the NL-MOD

accessory. See WI1242 for more information.

LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with “00”. However, for some

pager services, this will cause the Pager's Voice Mail feature to activate. This option allows you to program these digits to any

number desired. Typical Pager report is “003 022 1234”, where 3 is the Event, 22 is the zone, and 1234 is the Subscriber ID

number. For example, if the Leading Digits are programmed as “98”, the Pager report will now appear as “983 022 1234”.

1. Enter in 1st and 2nd Leading Digits in right digit only (left digit is not used) as shown.

2. Valid entries are: 0-9. Press U or D to save

CS RECEIVER FORMAT OPTIONS

ADDRESS 0575

CS Receiver 3

Format

ADDRESS 0520

Leading Digits

for Pager

Format

(1st Digit)

[Default = blank (•) blank (•)]

ADDRESS 0521

Leading Digits

for Pager

Format

(2nd Digit)

[Default = blank (•) blank (•)]

0526 CS Receiver 1 Options 0551

Default Option Default Option

OFF 1 1400Hz Handshake/Kissoff * OFF 1 1400Hz Handshake/Kissoff *

OFF 2 2300Hz Handshake/Kissoff * OFF 2 2300Hz Handshake/Kissoff *

OFF 3 Enable Zone Number on Pulse Alarm OFF 3 Enable Zone Number on Pulse Alarm

OFF 4 Single Digit Only OFF 4 Single Digit Only

OFF 5 Sum Check OFF 5 Sum Check

OFF 6 3/1 with Extended Restores OFF 6 3/1 with Extended Restores

OFF 7 Report to TCP/IP Receiver or AES (Telco 1)** OFF 7 Report to TCP/IP Receiver or AES (Telco 2)**

OFF 8 RESERVED OFF 8 RESERVED

CS Receiver 2 Options

0576

Default Option

OFF 1 1400Hz Handshake/Kissoff *

OFF 2 2300Hz Handshake/Kissoff *

OFF 3 Enable Zone Number on Pulse Alarm

OFF 4 Single Digit Only

OFF 5 Sum Check

OFF 6 3/1 with Extended Restores

OFF 7 Report to TCP/IP Receiver or AES (Telco 3)**

OFF 8 RESERVED

CS Receiver 3 Options

DATA ENTRIES

LEFT RIGHT

blank (•) blank (•) Ademco Slow, Silent Knight Slow

blank (•) 1 Sescoa, Vertex, DCI, Franklin Fast

blank (•) 2 Radionics Fast

blank (•) 3 Silent Knight Fast

blank (•) 4 Radionics, DCI, Franklin Slow

blank (•) 5 Universal High Speed

blank (•) 8 Radionics BFSK

blank (•) 9 FBI 4/3/1

blank (•) 0 Radionics Modem 2

blank (•) B SIA

blank (•) C Ademco Point ID

blank (•) D Ademco Express

blank (•) E Pager

1 blank (•) Radionics Modem IIe

CS RECEIVER FORMATS

blank (•) F Disabled

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 22 WI818G 10/05

CS Receiver

1 Telephone

Number

(Digits 1-20)

ADDRESS 0527-0546 (DIGITS 1-20)

0527 0528 0529 0530 0531 0532 0533 0534 0535 0536 0537 0538 0539 0540 0541 0542 0543 0544 0545 0546

CS Receiver

2 Telephone

Number

(Digits 1-20)

ADDRESS 0552-0571 (DIGITS 1-20)

0552 0553 0554 0555 0556 0557 0558 0559 0560 0561 0562 0563 0564 0565 0566 0567 0568 0569 0570 0571

CS Receiver

3 Telephone

Number

(Digits 1-20)

ADDRESS 0577-0596 (DIGITS 1-20)

0577 0578 0579 0580 0581 0582 0583 0584 0585 0586 0587 0588 0589 0590 0591 0592 0593 0594 0595 0596

CS RECEIVER TELEPHONE NUMBERS: Enter telephone numbers for any of the three CS Receivers (Telco 1, 2 & 3).

1. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•).

2. Valid entries are: 1-9, B = *button, C = #button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location

Default for CS

Receiver 1

Telephone Number

depends on Easy

Menu Question

“CENTRAL PHONE

#”.

[Default = blank (•)]

across digits 1-20 for

CS Receiver

Telephone Numbers

2 and 3.

CS RECEIVER TELEPHONE NUMBERS (ADDRESS 0527-0546, 0552-0571, 0577-0596)

DOWNLOAD/CALLBACK OPTIONS (ADDRESS 4089, 0600-0619, 0625-0647, 1022 & 1023)

ANSWER ON RING NUMBER: Enter the number of rings before automatic pickup by the control panel

when downloading from a computer (see Glossary in WI817). Initial value of 000 becomes 15 rings.

1. Enter digits only.

2. Valid entries are: 003-015. NOTE: Default is 15 Rings. Press U or D to save.

CALLBACK TELEPHONE NUMBERS: Enter telephone numbers to be used when downloading from a computer.

1. Enter digits only.

2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•).

3. Valid entries are: 0-9, B = *button, C = #button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location. Press U or D to save.

[Default = blank (•) for all digits 1-20]

ADDRESS 0600-0619 (DIGITS 1-20)

0600 0601 0602 0603 0604 0605 0606 0607 0608 0609 0610 0611 0612 0613 0614 0615 0616 0617 0618 0619

Callback

Telephone

Number 1

(Digits 1-20)

[Default = blank (•) for all digits 1-20]

ADDRESS 0625-0644 (DIGITS 1-20)

0625 0626 0627 0628 0629 0630 0631 0632 0633 0634 0635 0636 0637 0638 0639 0640 0641 0642 0643 0644

Callback

Telephone

Number 2

(Digits 1-20)

[Default = blank (•) blank (•)]

Download

Security Code

ADDRESS 0645-0647

0645 0646 0647

DOWNLOAD SECURITY CODE: Enter up to 6 digits to be used

for remote access when downloading from a computer.

1. Enter digits in address locations above.

2. Valid entries are: 0-9.

Note: Download Security Code must match the code entered in

the PCD-Windows Quickloader Download Software.

ADDRESS 1022

Callback

Telephone

No. Select

[Default = blank (•) blank (•)]

CALLBACK TELEPHONE NO. SELECT: Enter

either “1” for Callback Telephone Number 1 or

“2” for Callback Telephone Number 2.

1. Valid entries are: 1 or 2.

CS RECEIVER TELEPHONE NUMBERS & DOWNLOAD/CALLBACK OPTIONS

ADDRESS 1023

Auto Download

ID No.

[Default = blank (•) blank (•)]

Valid entries - 01-99

ADDRESS 4089

[Default = 015]

Answer on

Ring Number

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 23

WI818G 10/05

CS SUBSCRIBER ID NUMBERS (ADDRESS 0650-0787)

CS SUBSCRIBER ID NUMBERS (TELCO 1 & 2)

AREA 1

ADDRESS 0650-0653

(DIGITS 1-4)

0650 0651 0652 0653

CS TELCO 1 SUBSCRIBER OPENING/CLOSING ID NUMBERS

AREA 2

ADDRESS 0654-0657

(DIGITS 1-4)

0654 0655 0656 0657

AREA 1

ADDRESS 0682-0685

(DIGITS 1-4)

0682 0683 0684 0685

CS TELCO 1 SUBSCRIBER EVENT ID NUMBERS

AREA 2

ADDRESS 0686-0689

(DIGITS 1-4)

0686 0687 0688 0689

SYSTEM

ADDRESS 0714-0717

(DIGITS 1-4)

0714 0715 0716 0717

AREA 1

ADDRESS 0720-0723

(DIGITS 1-4)

0720 0721 0722 0723

CS TELCO 2 SUBSCRIBER OPENING/CLOSING ID NUMBERS (BACKUP REPORTING)

AREA 2

ADDRESS 0724-0727

(DIGITS 1-4)

0724 0725 0726 0727

AREA 1

ADDRESS 0752-0755

(DIGITS 1-4)

0752 0753 0754 0755

CS TELCO 2 SUBSCRIBER EVENT ID NUMBERS (BACKUP REPORTING)

AREA 2

ADDRESS 0756-0759

(DIGITS 1-4)

0756 0757 0758 0759

SYSTEM

ADDRESS 0784-0787

(DIGITS 1-4)

0784 0785 0786 0787

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 24 WI818G 10/05

CS REPORTING CODES (ADDRESS 0859-0883)

LEFT ADDR RIGHT

blank (•) 0859

blank (•) 0860

blank (•) 0861

blank (•) 0862

ADDRESS

0859-0862

ALARM/TROUBLE

REPORTING CODES

Cancel

Alarm Restore

Trouble

Trouble Restore

[Default = blank (•) blank (•) from address 0859-0883]

CS SYSTEM REPORTING CODES:

1. Enter in corresponding address loca-

tion (left and right digits).

NOTE: Left digit is the first digit and

right digit is the second digit in a two

digit CS receiver format.

2. Valid entries are: 1-9, 0 and B-F.

NOTE: A is not permitted.

3. To disable a code leave boxes blank

(•).

NOTE: Dark shaded data value box

shows option not available.

4. Press U or D to save.

Default for CS Telco 1 Subscriber Event ID Number (Area 1) depends on Easy Menu Question “ACCOUNT #”. [Default = blank (•) blank (•) blank (•)

blank (•)] for all other ID Numbers.

CS TELCO SUBSCRIBER ID NUMBERS: Enter the Subscriber Opening/Closing and Event ID Numbers for any of the 3 CS Receivers.

1. Enter 3 or 4 digits (depending on the CS receiver format) for each subscriber number from left to right.

NOTE: Leave trailing boxes blank (•).

2. Valid entries are: 1-9, 0 and B-F. NOTE: A is not permitted. Press [Enter] or ON/OFF] to save.

CS SUBSCRIBER ID NUMBERS (ADDRESS 0790-0857)

AREA 1

ADDRESS 0790-0793

(DIGITS 1-4)

0790 0791 0792 0793

CS TELCO 3 SUBSCRIBER OPENING/CLOSING ID NUMBERS

AREA 2

ADDRESS 0794-0797

(DIGITS 1-4)

0794 0795 0796 0797

AREA 1

ADDRESS 0822-0825

(DIGITS 1-4)

0822 0823 0824 0825

CS TELCO 3 SUBSCRIBER EVENT ID NUMBERS

AREA 2

ADDRESS 0826-0829

(DIGITS 1-4)

0826 0827 0828 0829

SYSTEM

ADDRESS 0854-0857

(DIGITS 1-4)

0854 0855 0856 0857

CS SUBSCRIBER ID NUMBERS (TELCO 3) & CS REPORTING CODES

OPENING/CLOSING

REPORTING CODES

ADDRESS 0864-0883

ADDR

Closing blank (•) 0864

Conditional Closing blank (•) 0865

Opening blank (•) 0866

Opening after Alarm blank (•) 0867

Fail to Open 0868

Fail to Close 0869

Telemetry Trouble 0882

Telemetry Fail 0883

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 25

WI818G 10/05

CS SYSTEM REPORTING CODES:

1. Enter in corresponding address location

(left and right digits).

NOTE: Left digit is the first digit and right

digit is the second digit in a two digit CS

receiver format.

2. Valid entries are: 1-9, 0 and B-F.

NOTE: A is not permitted.

3. To disable a code leave boxes blank (•).

NOTE: Dark shaded data value box

shows option not available.

4. Press U or D to save.

LEFT ADDR RIGHT

0870

0871

0872

0873

0874

0875

0876

0877

blank (•) 0878 blank (•)

blank (•) 0879 blank (•)

0880

ADDRESS

0870-0880

SYSTEM REPORTING

CODES

Test Timer

Alarm Supervisory

Bus Failure

Memory Failure

Low Battery

AC Failure

EZM Tamper

Sensor Watch

RESERVED

Telco Line Failure

CS REPORTING CODES (ADDRESS 0870-0904)

[Default = blank (•) blank (•) from address 0870-0904]

LEFT ADDR RIGHT

0890

0891

0892

0893

0894

0895

0896

0897

ADDRESS

0890-0897

SYSTEM REPORTING

CODES

Digital Dialer Test

RESERVED

Service Message

Program Change

RF Receiver Trouble

RF Tamper

RF Trouble

LEFT ADDR RIGHT

0900

0901

0902

0903

0904

ADDRESS

0900-0904

KEYPAD REPORTING

CODES

Ambush

Panic

Fire

Auxiliary

Tamper

CAUTION: For all 2-Digit Reporting Formats (see CS Receiver Format Options), use the following:

Example: The 2-digit reporting code as shown is “21”.

LEFT RIGHT

1 2

ADDRESS Loc.

Reporting

Code

2nd Digit of Reporting Code 1st Digit of Reporting Code

CS AREA & SYSTEM REPORTING OPTIONS (ADDRESS 1024-1027)

* NOTE: If neither TouchTone Dialing nor

TouchTone w/Rotary Backup is selected, then

system defaults automatically to Rotary Dialing.

Leave blank (•) to select Rotary Dialing.

CS REPORTING CODES & CS REPORTING OPTIONS

1027

Default Option

OFF 1 Backup Report on Telco 2

OFF 2 Touch-tone Dialing Only *

ON 3 Touch-tone Dialing w/Rotary Backup *

OFF 4 Transmit “402” Opening/Closing Code

OFF 5 Cancel Next Test Timer on any Report

OFF 6 Disable Wait for Silence

OFF 7 Disable Wait for Handshake

OFF 8 Handshake for Local Telemetry

CS System Report Options CS AREA & SYSTEM REPORTING OPTIONS:

1. Select the desired option entering the

option number (1-8) for each digit.

2. Enter corresponding option number in

address location.

NOTE: Dark shaded data value box shows op-

tion not available.

3. Press U or D to save.

AREAS 1  2

CS Area Reporting Options ADDRESS A1 A2

1 2

DISABLE OPENING REPORTS 1024

DISABLE CLOSING REPORTS 1025

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 26 WI818G 10/05

ADDRESS 0910-0917

ZONES REPORT CODE (CONTROL PANEL)

ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8

0910 0911 0912 0913 0914 0915 0916 0917

ADDRESS 0918-0921

ZONES REPORT CODE (GROUP 1)

ZONE 9 ZONE 10 ZONE 11 ZONE 12

0918 0919 0920 0921

ADDRESS 0922-0925

ZONES REPORT CODE (GROUP 2)

ZONE 13 ZONE 14 ZONE 15 ZONE 16

0922 0923 0924 0925

ADDRESS 0934-0937

ZONES REPORT CODE (GROUP 5)

ZONE 25 ZONE 26 ZONE 27 ZONE 28

0934 0935 0936 0937

ADDRESS 0938-0941

ZONES REPORT CODE (GROUP 6)

ZONE 29 ZONE 30 ZONE 31 ZONE 32

0938 0939 0940 0941

ADDRESS 0926-0929

ZONES REPORT CODE (GROUP 3)

ZONE 17 ZONE 18 ZONE 19 ZONE 20

0926 0927 0928 0929

ADDRESS 0930-0933

ZONES REPORT CODE (GROUP 4)

ZONE 21 ZONE 22 ZONE 23 ZONE 24

0930 0931 0932 0933

Default for Group Zone Report Codes depends on Easy Menu Question “RCVR. FORMAT”.

7 Gas Alarm

8 Heat Alarm

0 Auxiliary Alarm

B 24 Hour Auxiliary

1

2

3

4

DATA

ENTRIES MODEM CODE

Fire *

Panic

Burglary

Hold up

ZONE REPORT

CODE OPTIONS

DATA ENTRIES

NOTE: Zones 1-8 are included in the control panel and Zones 9-32 are EZM Zones.

Zones 33-48 are wireless. See Address 2555-2560 to enable “EZM Zone Groups”.

PULSE EVENT CODE will be the first digit of the 2 digit reporting code. The second digit will be the

second digit of the reporting zone. For example, for zone 9 (address 0918), if the right digit is “3",

then the reporting code is “39”. With another example, for zone 15 (address 0924), if the right digit is

“4", then the reporting code is “45”.

MODEM CODES determine the zone types reported for the following formats: SIA and ADEMCO Point ID.

1. Select the desired Modem Code for each zone from the table shown.

2. Press U or D to save.

CS ZONE REPORTING CODES (ADDRESS 0910-0957)

ADDRESS 0950-0953

ZONES REPORT CODE (GROUP 9)

ZONE 41 ZONE 42 ZONE 43 ZONE 44

0950 0951 0952 0953

ADDRESS 0954-0957

ZONES REPORT CODE (GROUP 10)

ZONE 45 ZONE 46 ZONE 47 ZONE 48

0954 0955 0956 0957

ADDRESS 0942-0945

ZONES REPORT CODE (GROUP 7)

ZONE 33 ZONE 34 ZONE 35 ZONE 36

0942 0943 0944 0945

ADDRESS 0946-0949

ZONES REPORT CODE (GROUP 8)

ZONE 37 ZONE 38 ZONE 39 ZONE 40

0946 0947 0948 0949

CS ZONE REPORTING CODES

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 27

WI818G 10/05

CS USER REPORTING CODES (ADDRESS 1030-1074)

NOTE: These opening events will report as the user

number shown. Also, Keyfobs 1-8 (see Easy Menu

Program Driven Mode) will report as Users 25-32,

respectively.

CS USER REPORTING CODES

USERS 1  8 USERS 9  16

ADDR U1 U2 U3 U4 U5 U6 U7 U8 ADDR U9 U10 U11 U12 U13 U14 U15 U16

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

User Opening Telco 1 1030 1031

User Closing Telco 1 1043 1044

User Opening Telco 3 1056 1057

User Closing Telco 3 1069 1070

Enable Users to Report

USERS 17  24 USERS 25  32

ADDR U17 U18 U19 U20

4 U21 U22 U23 U24 ADDR U25 U26 U27 U28 U29 U30 U31 U32

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

User Opening Telco 1 1032 1033

User Closing Telco 1 1045 1046

User Opening Telco 3 1058 1059

User Closing Telco 3 1071 1072

Enable Users to Report

USERS 33  40 USERS 41  48

ADDR U33 U34 U35 U36 U37 U38 U39 U40 ADDR U41 U42 U43 U44 U45 U46 U47 U48

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

User Opening Telco 1 1034 1035

User Closing Telco 1 1047 1048

User Opening Telco 3 1060 1061

User Closing Telco 3 1073 1074

Enable Users to Report

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 28 WI818G 10/05

GLOBAL SYSTEM EVENT/TROUBLE

SYSTEM RESPONSE

ACTIVATED BY GLOBAL

EVENT/TROUBLE

ADDR TEST

TIMER

ALARM

SUPERV.

COMM.

BUS 1

MEMORY

FAILURE

LOW

BATTERY AC FAIL EZM

TAMPER

SENSOR

WATCH

1 2 3 4 5 6 7 8

Burglary Alarm Output 1082

Pulsed Burg. Output 1083

Fire Output (Lug E9) 1084

Reset Relay 1085

Auxiliary Relay 1086

Report Event Telco 1 1087

Report Restore Telco 1 1088

Report Event Telco 3 1091

Report Restore Telco 3 1092

1. Select the desired option entering the option number (1-8) for each digit.

2. Enter corresponding option number in address location.

NOTE: Dark shaded data value box shows option not available. Press U or D to save.

SYSTEM RESPONSE

ACTIVATED BY GLOBAL

EVENT/TROUBLE

GLOBAL SYSTEM EVENT/TROUBLE

ADDR TELCO

FAIL RSRVD. Telemetry

Trouble

Telemetry

Failure RSRVD. RSRVD. RSRVD. RSRVD.

1 2 3 4 5 6 7 8

Burglary Alarm Output 1094

Pulsed Burg. Output 1095

Fire Output (Lug E9) 1096

Reset Relay 1097

Auxiliary Relay 1098

Report Event Telco 1 1099

[Default = blank (•) from address 1094-1104] * NOTE: Keypad Aux. is not to be selected for UL Installations.

Report Restore Telco 1 1100

Report Event Telco 3 1103

Report Restore Telco 3 1104

SYSTEM RESPONSE

ACTIVATED BY GLOBAL

EVENT/TROUBLE

GLOBAL SYSTEM EVENT/TROUBLE

ADDR Digital

Dialer Test RSRVD. RSRVD. SERVICE

MESSAGE

PROGRAM

CHANGE

RF RCVR.

TROUBLE

RF

TAMPER

RF

TROUBLE

1 2 3 4 5 6 7 8

Burglary Alarm Output 1106

Pulsed Burg. Output 1107

Fire Output (Lug E9) 1108

Reset Relay 1109

Auxiliary Relay 1110

Report Event Telco 1 1111

[Default = blank (•) blank (•) from address 1106-1116] * NOTE: Keypad Aux. is not to be selected for UL Installations.

Report Restore Telco 1 1112

Report Event Telco 3 1115

Report Restore Telco 3 1116

[Default = blank (•) from address 1082-1092].

GLOBAL SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1082-1116)

GLOBAL SYSTEM TROUBLE REPORTING OPTIONS

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 29

WI818G 10/05

AREA SYSTEM TROUBLE REPORTING OPTIONS

AREA SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1120-1137)

1. Select the desired option entering the option number (1-8) for each digit.

2. Enter corresponding option number in address location.

NOTE: Dark shaded data value box shows option not available.

3. Press U or D to save.

SYSTEM RESPONSE

ACTIVATED BY AREA 1

EVENT/TROUBLE

AREA 1 SYSTEM EVENT/TROUBLE

ADDR AMBUSH KEYPAD

PANIC

KEYPAD

FIRE

KEYPAD

AUX.

KEYPAD

TAMPER

FAIL TO

OPEN

FAIL TO

CLOSE RSRVD.

1 2 3 4 5 6 7 8

Pulsed Burg. Output 1120 Default ON

Burglary Output 1121 Default ON Default ON

Fire Output (Lug E9) 1122

Reset Relay 1123

Auxiliary Relay 1124

Report Alarm Telco 1 1125

Report Alarm Telco 3 1127

Defaults as noted from address 1120-1127]

SYSTEM RESPONSE

ACTIVATED BY AREA 2

EVENT/TROUBLE

AREA 2 SYSTEM EVENT/TROUBLE

ADDR AMBUSH KEYPAD

PANIC

KEYPAD

FIRE

KEYPAD

AUX.

KEYPAD

TAMPER

FAIL TO

OPEN

FAIL TO

CLOSE RSRVD.

1 2 3 4 5 6 7 8

Pulsed Burg. Output 1130 Default ON

Burglary Output 1131 Default ON Default ON

Fire Output (Lug E9) 1132

Reset Relay 1133

Auxiliary Relay 1134

Report Alarm Telco 1 1135 Default ON Default ON Default ON

Report Alarm Telco 3 1137

[Defaults as noted from address 1130-1137]

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 30 WI818G 10/05

ZONES 1  8 ZONES 9  16

ZONE OPTIONS ADDR Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 ADDR Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

50ms Loop Response (A) 1200

20ms Loop Response (A) 1201

 Priority 1202 1302

Priority with Bypass 1203 1303

Auto-Bypass 1204 1304

 Selective Bypass 1205 1305

Keyswitch Arming 1206 1306

Auto-Bypass Re-entry 1207 1307

Pre-Alarm Warning 1208 1308

Never Arm 1209 1309

24-Hour Zone 1210 1310

 Burg. Alarm Output 1211 1311

 Pulsed Alarm Output 1212 1312

Fire Output (Lug E9) 1213 1313

Reset Relay 1214 1314

Auxiliary Relay 1215 1315

Entry/Exit 1 1216 1316

Entry/Exit 2 1217 1317

Exit/Entry Follower 1218 1318

  Auto Reset 1219 1319

  Swinger Shutdown 1220 1320

Chime 1221 1321

Abort Delay 1222 1322

Power-up Delay 1223 1323

Day Zone Open 1224 1324

Day Zone Short 1225 1325

Alarm on Day Zone 1226 1326

RPT Alarm Tel 1 1227 1327

RPT Alarm Restore Tel 1 1228 1328

RPT Trouble Tel 1 1229 1329

RPT Trouble Restore Tel 1 1230 1330

RPT Alarm Tel 3 1235 1335

RPT Alarm Restore Tel 3 1236 1336

RPT Trouble Tel 3 1237 1337

RPT Trouble Restore Tel 3 1238 1338

No EOL Resistor 1239 1339

Sensor Watch 1240 1340

Trouble on Open 1241 1341

Trouble on Short 1242 1342

Trouble on Night Open 1243 1343

 Zone Area 1 1244 1344

Zone Area 2 1245 1345

2-Wire Smoke Detectors (B) 1252

RESERVED 1253 1353

Zone ANDing Group 1 1254 1354

Zone ANDing Group 2 1255 1355

Interior #1 Bypass 1262 1362

 Interior #2 Bypass 1263 1363

Keypad Sounder on Alarm 1264 1364

Fire (C) 1275 1375

Fire Alarm Verification (C) 1276 1376

Interior (STAY) Bypass 1284 1384

Chime 2 1286 1386

 When the Easy Program Menu is used, these features are enabled by default (for new panels or after a Cold Start (address 4093)). Zone Area 1

is enabled for the first 8 zones only, by default

 Do not program if "K Series" keypads (with "P" and "Q" buttons) are used in the system.

 Disable Auto-Reset on non-fire zones for SIA CP-01 installations.

 In UL installations, all Fire Zones must also be programmed for "Pulse Burg Output Cadence" (Address 2422, press 1 (bit zero)).

ZONE OPTIONS / ZONES 1-16 (ADDRESS 1200-1386)

ZONE OPTIONS / ZONES 1-16

See Zone Options on Page 33.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 31

WI818G 10/05

ZONE OPTIONS / ZONES 17-32 (ADDRESS 1402-1586)

ZONE OPTIONS / ZONES 17-32

ZONES 17  24 ZONES 25  32

ZONE OPTIONS ADDR Z17 Z18 Z19 Z20 Z21 Z22 Z23 Z24 ADDR Z25 Z26 Z27 Z28 Z29 Z30 Z31 Z32

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

 Priority 1402 1502

Priority with Bypass 1403 1503

Auto-Bypass 1404 1504

 Selective Bypass 1405 1505

Keyswitch Arming 1406 1506

Auto-Bypass Re-entry 1407 1507

Pre-Alarm Warning 1408 1508

Never Arm 1409 1509

24-Hour Zone 1410 1510

 Burg. Alarm Output 1411 1511

 Pulsed Alarm Output 1412 1512

Fire Output (Lug E9) 1413 1513

Reset Relay 1414 1514

Auxiliary Relay 1415 1515

Entry/Exit 1 1416 1516

Entry/Exit 2 1417 1517

Exit/Entry Follower 1418 1518

  Auto Reset 1419 1519

  Swinger Shutdown 1420 1520

Chime 1421 1521

Abort Delay 1422 1522

Power-up Delay 1423 1523

Day Zone Open 1424 1524

Day Zone Short 1425 1525

Alarm on Day Zone 1426 1526

RPT Alarm Tel 1 1427 1527

RPT Alarm Restore Tel 1 1428 1528

RPT Trouble Tel 1 1429 1529

RPT Trouble Restore Tel 1 1430 1530

RPT Alarm Tel 3 1435 1535

RPT Alarm Restore Tel 3 1436 1536

RPT Trouble Tel 3 1437 1537

RPT Trouble Restore Tel 3 1438 1538

No EOL Resistor 1439 1539

Sensor Watch 1440 1540

Trouble on Open 1441 1541

Trouble on Short 1442 1542

Trouble on Night Open 1443 1543

Zone Area 1 1444 1544

Zone Area 2 1445 1545

RESERVED 1453 1553

Zone ANDing Group 1 1454 1554

Zone ANDing Group 2 1455 1555

Interior #1 Bypass 1462 1562

 Interior #2 Bypass 1463 1563

Keypad Sounder on Alarm 1464 1564

Fire (C) 1475 1575

Fire Alarm Verification (C) 1476 1576

Interior (STAY) Bypass 1484 1584

Chime 2 1486 1586

 When the Easy Program Menu is used, these features are enabled by default (for new panels or after a Cold Start (address 4093)).

 Do not program if "K Series" keypads (with "P" and "Q" buttons) are used in the system.

 Disable Auto-Reset on non-fire zones for SIA CP-01 installations.

 In UL installations, all Fire Zones must also be programmed for "Pulse Burg Output Cadence" (Address 2422, press 1 (bit zero)).

See Zone Options on Page 33.

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 32 WI818G 10/05

ZONE OPTIONS / ZONES 33-48 (ADDRESS 1602-1786)

ZONE OPTIONS / ZONES 33-48

ZONES 33  40 ZONES 41  48

ZONE OPTIONS ADDR Z33 Z34 Z35 Z36 Z37 Z38 Z39 Z40 ADDR Z41 Z42 Z43 Z44 Z45 Z46 Z47 Z48

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

 Priority 1602 1702

Priority with Bypass 1603 1703

Auto-Bypass 1604 1704

 Selective Bypass 1605 1705

Keyswitch Arming 1606 1706

Auto-Bypass Re-entry 1607 1707

Pre-Alarm Warning 1608 1708

Never Arm 1609 1709

24-Hour Zone 1610 1710

 Burg. Alarm Output 1611 1711

 Pulsed Alarm Output 1612 1712

Fire Output (Lug E9) 1613 1713

Reset Relay 1614 1714

Auxiliary Relay 1615 1715

Entry/Exit 1 1616 1716

Entry/Exit 2 1617 1717

Exit/Entry Follower 1618 1718

  Auto Reset 1619 1719

  Swinger Shutdown 1620 1720

Chime 1621 1721

Abort Delay 1622 1722

Power-up Delay 1623 1723

Day Zone Open 1624 1724

Day Zone Short 1625 1725

Alarm on Day Zone 1626 1726

RPT Alarm Tel 1 1627 1727

RPT Alarm Restore Tel 1 1628 1728

RPT Trouble Tel 1 1629 1729

RPT Trouble Restore Tel 1 1630 1730

RPT Alarm Tel 3 1635 1735

RPT Alarm Restore Tel 3 1636 1736

RPT Trouble Tel 3 1637 1737

RPT Trouble Restore Tel 3 1638 1738

No EOL Resistor 1639 1739

Sensor Watch 1640 1740

Trouble on Open 1641 1741

Trouble on Short 1642 1742

Trouble on Night Open 1643 1743

Zone Area 1 1644 1744

Zone Area 2 1645 1745

RESERVED 1653 1753

Zone ANDing Group 1 1654 1754

Zone ANDing Group 2 1655 1755

Interior #1 Bypass 1662 1762

 Interior #2 Bypass 1663 1763

Keypad Sounder on Alarm 1664 1764

Fire (C) 1675 1775

Fire Alarm Verification (C) 1676 1776

Interior (STAY) Bypass 1684 1784

Chime 2 1686 1786

 When the Easy Program Menu is used, these features are enabled by default (for new panels or after a Cold Start (address 4093)).

 Do not program if "K Series" keypads (with "P" and "Q" buttons) are used in the system.

 Disable Auto-Reset on non-fire zones for SIA CP-01 installations.

 In UL installations, all Fire Zones must also be programmed for "Pulse Burg Output Cadence" (Address 2422, press 1 (bit zero)).

See Zone Options on Page 33.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 33

WI818G 10/05

NOTES: (A) 50ms & 20 ms Loop Response only available for zones 1-8.

(B) 2-wire Smoke Detectors only available for zones 1-8. Refer to Installation Instructions (WI817) for more details. If 2-wire Smoke

Detector is selected, then Fire must also be selected.

(C) If Fire Alarm Verification is selected, then Fire must also be selected.

DEFAULTS: The zone options indicated are automatically set after exiting the Easy Menu Driven Mode.

Priority, Selective Bypass, Alarm Output, Auto Reset, Swinger Shutdown , Zone Area 1 and Zone Area 2 are enabled for the total number

of zones entered in “AREA 1 # ZONES = 08” and “AREA 2 # ZONES = 00”.

Alarm Telco 1 is enabled for the zones if [YES] is entered for “REPORT ALL ZONES TO CENTRAL ZONES? Y/N”.

Entry/Exit 1 and Chime are enabled for zone numbers entered in “EXIT / ENTRY ZONES”.

Exit/Entry Follower and Interior Bypass are enabled for zone numbers entered in “INTERIOR ZONES”.

Fire, Pulse Alarm Output and Fire Verification is enabled for the zone numbers entered in “FIRE ZONES”.

2-Wire Smoke Detector is enabled for zone numbers entered in “2 WIRE FIRE ZONES”.

Note: See “Number of Zones

& Keypads per Area” in Easy

Menu Driven program Mode.

ZONE OPTIONS / ZONES 1-48 (ADDRESS 1200-1786)

ZONE OPTIONS / ZONES 1-48

ZONE OPTIONS: Select zone options for any zone.

1. Select the desired zone option by entering the option number (1-8) for each selected zone.

2. Enter corresponding option number in address location, in Binary (Bit) Format.

NOTE: Dark shaded data value box shows option not available. Press U or D to save

NOTE: See Direct Address Programming Example on page 15.

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 34 WI818G 10/05

SYSTEM OPTIONS (ADDRESS 2415-2419)

SYSTEM OPTIONS

2417 System Options 2418 System Options

Default Option Default Option

OFF 1 Opening Report only after Alarm Report OFF 1 Auto Bell Test on Arming

OFF 2 Closing Report only on Cond. Closing (Auto-Byp.) ON 2 Auto Reset after Burg. Output Timeout

OFF 3 Include Sel./Grp. Bypass in Cond. Closing Status OFF 3 Suppress “Bypass” Icon when Armed

OFF 4 Status Report (Auto-Byp. Zones on Clos.) OFF 4 RESERVED

OFF 5 RESERVED OFF 5 Access Control (Panel) on Aux. Output

OFF 6 Lug E4 Armed Away Only OFF 6 Enable Burg. Output Warning on Entry

OFF 7 Disable Auto-Unbypass on Disarming OFF 7 Enable Manager’s Mode Outside Overview

OFF 8 Enable All-Zone-in-Trouble Bypass OFF 8 Start Exit Delay after Ringback

2419 System Options

Default Option

OFF 1 Interior 1 Normally Bypassed*

OFF 2 Enable Exit-Delay Restart

OFF 3 Reset Day Zone with Arm/Disarm Only

OFF 4 Enable Local Alarm on First Zone “AND” Trip

OFF 5 Disable Keypad Function-Mode Download

OFF 6 Disable Callback Download

OFF 7 Disable Answering-Machine Download

OFF 8 Disable Auto-Reset on Day Zone

*Do not use on systems with "K Series " keypads.

SYSTEM OPTIONS:

1. Select the desired option entering the option

number (1-8) for each digit.

2. Enter corresponding option number in address

location.

NOTE: Dark shaded data value box shows option not

available. Press U or D to save.

2415 System Options - Disable Fire Reset 2416 System Options - Enable Day Zone Watch

Default Option Default Option

OFF 1 Disable Fire Reset (Area 1) OFF 1 Enable Day Zone Watch (Area 1)

OFF 2 Disable Fire Reset (Area 2) OFF 2 Enable Day Zone Watch (Area 2)

OFF 3 RESERVED OFF 3 RESERVED

OFF 4 RESERVED OFF 4 RESERVED

OFF 5 RESERVED OFF 5 RESERVED

OFF 6 RESERVED OFF 6 RESERVED

OFF 7 RESERVED OFF 7 RESERVED

OFF 8 RESERVED OFF 8 RESERVED

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 35

WI818G 10/05

SYSTEM OPTIONS (ADDRESS 2420-2422, 3874, 3905, 3880-3881)

SYSTEM OPTIONS

3905 System Options

Default Option

OFF 1 RESERVED

OFF 2 Enable Exit Delay Restart (SIA-FAR)**

OFF 3 Enable Bell on Exit Error**

OFF 4 Enable Report Exit Err/Recent Close**

OFF 5 Digital Dialer Rpt Enter/Exit Test Mode**

OFF 6 Enable CP-01 Limits**

OFF 7 Disable Call Waiting on First Attempt

OFF 8 Enable Ambush in User Assignment Code Type

** Default for this addresses contingent on EZ Menu selections.

2420 System Options 2421 System Options

Default Option Default Option

OFF 1 Disable System Trouble Audible (at Keypad) † OFF 1 Automatic Interior Bypass/Easy Exit

OFF 2 Chime on Lug E4 OFF 2 Veri-phone Zones trip Aux. Output

OFF 3 Disable Code required for Func. Mode Lvl. 1 OFF 3 Veri-phone Zones Priority over Alarms

OFF 4 Disable Code required for EZ Bypass OFF 4 AuxOut Chirp on Keyfob Arm/Disarm**

OFF 5 Disable Keypad Instant Button OFF 5 Disable Auxout Clear on Disarm

OFF 6 Enable Telephone Line-Fault Test OFF 6 2nd Call Answering Machine Override

OFF 7 Disable AC Fail Detection OFF 7 Disable Zone Fault Scrolling (Auto Status)

OFF 8 Telco Fail only when Armed OFF 8 Veri-phone Zones trip Fire Output

† NOTE: Not for UL Installations.

** Default for this address contingent on EZ Menu selections.

2422 System Options 3874 System Options

Default Option Default Option

ON 1 Pulse Burg Output Cadence§ OFF 1 Enable GEM-PRINT

OFF 2 Wireless Smoke Low Battery Resound OFF 2 Enable Cancel Report to Telco 3

OFF 3 Supervised Alarm Output OFF 3 Wireless Trouble to Telco 1

OFF 4 Enable Smoke Detector Dirty Trouble OFF 4 Wireless Trouble to Telco 3

OFF 5 Disable Area Entry Relays OFF 5 Enable Set Time/Date Message

OFF 6 Disable Exit/Entry Urgency Tone at Keypad OFF 6 RESERVED

OFF 7 Select Bell Output on Keyfob Arming ON 7 Enable Keypad Time/Date Display

OFF 8 Enable Burg. Output on Telco Fail only when Armed 8 RESERVED

SYSTEM OPTIONS:

1. Select the desired option entering the option

number (1-8) for each digit.

2. Enter corresponding option number in address

location.

NOTE: Dark shaded data value box shows option not

available. Press U or D to save.

ALARM/TROUBLE

REPORTING CODES

ADDRESS 3880-3881

Wireless Supervisory 3880

Wireless Tamper 3881

[Default = blank (•) from address 3880-3881]

ALARM/TROUBLE REPORTING CODES (ADDRESS 3880-3881)

ALARM/TROUBLE REPORTING CODES:

1. Enter in corresponding address location (left and right digits).

NOTE: Left digit is the first digit and right digit is the second digit in a two digit CS receiver

format.

2. Valid entries are: 1-9, 0 and B-F.

NOTE: A is not permitted.

3. To disable a code leave boxes blank (•).

4. Press U or D to save.

§In Zone Options, Fire Zones, and only Fire Zones,

must be programmed for pulse alarm output.

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 36 WI818G 10/05

[Default = blank (•) blank (•)]

LEFT DIGIT (SUM

OF DATA VALUES)

RIGHT DIGIT (SUM

OF DATA VALUES)

blank (•)

ADDRESS 4084

LEFT DATA

VALUES

1

2

4

8

SYSTEM OPTIONS

RESERVED

Skip Automatic

Dial Tone Detect

Note: Right digit is RESERVED

(not used). Enter data in left

digit only.

SYSTEM OPTIONS (ADDRESS 3882-3901, 3903-3905 & 4084)

Telephone Dialing

Prefix (Digits 1-20)

ADDRESS 3882-3901 (RIGHT DIGITS 1-20)

3882 3883 3884 3885 3886 3887 3888 3889 3890 3891 3892 3893 3894 3895 3896 3897 3898 3899 3900 3901

[Default = blank (•) blank (•)]

LEFT RIGHT

ADDRESS 3903

Pager Recalls

[Default = blank (•) blank (•)]

LEFT RIGHT

ADDRESS 3904

Pager Format:

Maximum Pages

per Session

SYSTEM OPTIONS

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 37

WI818G 10/05

RIGHT

blank (•)

1

2

OPTION

Not Used

Area 1

Area 2

KEYPAD AREA

ASSIGNMENT

KEYPAD OPTIONS (ADDRESS 2425-2446)

KEYPAD OPTIONS

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 2428

Keypad 4 Type

& Area

Assignment

[Default = blank (•) 1]

LEFT RIGHT

ADDRESS 2425

Keypad 1 Type

& Area

Assignment

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 2426

Keypad 2 Type

& Area

Assignment

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 2427

Keypad 3 Type

& Area

Assignment

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 2429

Keypad 5 Type

& Area

Assignment

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 2430

Keypad 6 Type

& Area

Assignment

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 2431

Keypad 7 Type

& Area

Assignment

KEYPAD TYPE & AREA ASSIGNMENT: Up to 7 keypads may be programmed, if they

are connected.

NOTE: See Keypad Configuration Mode. By default from the factory, each keypad is

configured as number 1.

1. Select keypad type & area assignment for each keypad from the tables shown.

2. Enter in corresponding right and left digit address locations above.

LEFT OPTION

blank

(•)

Burg Keypad

2 Wizard Keypad

KEYPAD TYPE

KEYPAD NUMBER

KEYPAD OPTIONS

ADDR KEYPAD

FIRE

KEYPAD

AUXILIARY

KEYPAD

PANIC

Rem. Acc.

Only * AMBUSH EASY

ARMING

PANEL

ACCESS

TOUR

STATION

1 2 3 4 5 6 7 8

1 2440 default ON default ON default ON default ON

2 2441 default ON default ON default ON default ON

3 2442 default ON default ON default ON default ON

4 2443 default ON default ON default ON default ON

5 2444 default ON default ON default ON default ON

6 2445 default ON default ON default ON default ON

7 2446 default ON default ON default ON default ON

[Defaults as noted for address 2440-2446]

KEYPAD OPTIONS: Select options for any of the 7 keypads.

* Note: For Remote Access Control only (no Arm/Disarm capability).

1. Select the desired option entering the option number (1-8) for each digit.

2. Enter corresponding option number in address location.

3. Press U or D to save.

NOTE: Dark shaded data value box shows option not available.

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 38 WI818G 10/05

ACM OPTIONS

ACM ZONE OPTIONS (ADDRESS 2740-2769)

ACM GLOBAL FLAGS (ADDRESS 2780)

ACM TIMEOUTS (ADDRESS 2782-2783)

ACM ZONE OPTIONS:

Enter the Zone numbers (in decimal 1-48 format) for each option in the table below. Press U or D to save.

NOTE: Dark shaded data value box shows option not available. Note: The Area # for Door 1 is controlled by the ex-

isting Keypad Programming table (Address 2425 to 2431). The assigned area for Door #2 for each ACM must be en-

tered in the table below (addresses 2748 and 2758) and must not be left blank if Door 2 is to be used.

ACM1 Zone Options Door 1 ADDR Door 2

Door Contact 2740

2745

Forced Entry Zone 2741 2746

Door Ajar Zone 2742 2747

ADDR

Area # for Door 2 2748

Reserved 2743 2749

Reserved 2744

ACM2 Zone Options Door 1 ADDR Door 2

Door Contact 2750

2755

Forced Entry Zone 2751 2756

Door Ajar Zone 2752 2757

ADDR

Area # for Door 2 2758

Reserved 2753 2759

Reserved 2754

2780 ACM Global Flags

Default Option

OFF 1 Enable Two-Swipe Arming

OFF 2 Enable NAPCO Proprietary Access Format

OFF 3 Enable Facility Code

OFF 4 Enable Access Logging into Burg Log

OFF 5 Enable Printing of Access Events

OFF 6 Enable Card Presentation Beep and Green LED Flash

OFF 7 RESERVED

OFF 8 RESERVED

ACM GLOBAL FLAGS:

1. Select the desired option entering the option number

(1-8) for each digit.

2. Enter corresponding option number in address loca-

tion.

NOTE: Dark shaded data value box shows option not

available. Press U or D to save.

ADDRESS 2782

[Default = 030 = 3 seconds.]

Maximum

Two-Swipe

Arm Time

(x100ms)

ADDRESS 2783

[Default = 005 = 5 sec.]

Unlock Time

(sec.)

Enable ACM Access (address 2423) must be enabled.

Address 2782 determines the maximum time allowed for the double swipe (x100ms). Address 2783 determines the door unlock

time, in seconds, after a successful entry.

1. Select timeout (1-255).

2. Enter in corresponding address locations above and right. Press U or D to save.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 39

WI818G 10/05

ACM OPTIONS

ACM DOOR AREA OPTIONS (ADDRESS 2784-2787)

ACM SCHEDULED FREE ACCESS (ADDRESS 4072-4075)

ACM Door Number ADDR

ACM DOOR AREA OPTIONS

Arm All

Areas

Allowed

Disarm All

Areas

Allowed

Stealth

Mode RSRVD. RSRVD. RSRVD. RSRVD. RSRVD.

1 2 3 4 5 6 7 8

ACM 1 - Door 1 2784

ACM 1 - Door 2 2785

ACM 2 - Door 1 2786

ACM 2 - Door 2 2787

[Default = blank (•) blank (•) from address 2784-2787]

ACM DOOR AREA OPTIONS:

1. Select the desired option entering the option number (1-3) for each address.

2. Enter corresponding option number in address location.

NOTE: Dark shaded data value box shows option not available. Press U or D to save.

ACM SCHEDULED FREE ACCESS:

1. Enter the Scheduled Free Access Index (1-24)

(Relay #1-24) for each option in the table at right.

2. Press U or D to save.

Scheduled Free Access Index

ADDR Relay Number

ACM 1 – Door 1 – 4072

ACM 1 – Door 2 – 4073

ACM 2 – Door 1 – 4074

ACM 2 – Door 2 – 4075

[Default = blank (•) blank (•) from address 4072-4075]

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 40 WI818G 10/05

ACM OPTIONS

ACM ZONE OPTIONS:

Enter the Zone numbers (in two-digit hexadecimal format) for each option in the table below.

The left digit (nibble) determines the type of device: "●" for Keypad and "1" for ACM.

The right digit (nibble) determines the home area (1 or 2) of the specified device.

Press U or D to save.

KEYPAD HOME AREA / ACM DOOR #1 AREA (HEX)

(ADDRESS 2425-2431)

KEYPAD HOME AREA / ACM DOOR #1 AREA (HEX)

(ADDRESS 2425-2431)

ACM / Keypad ADDRESS DEVICE TYPE

(●) or 1 AREA # (1 or 2)

1 2425 See *Note at bottom

2 2426

3 2427

4 2428

5 2429

6 2430

7 2431

[Default = blank (•) 1 for address 2425

blank (•) blank (•) for addresses 2426-2431]

* Note: First device should be a keypad.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 41

WI818G 10/05

SYSTEM OPTIONS (ADDRESS 2423)

SYSTEM OPTION:

1. Select the System Option from the table shown and enter in the corresponding address location at right. Keypad Blank-

ing will clear all data from the LCD display (and turn off all keypad LED's) after the system is armed and delay time has ex-

pired. The display will re-appear when an exit/entry door is faulted, causing an entry time delay display, or if a valid user code

is entered at the keypad while the system is armed.

2. Press U or D to save. NOTE: Dark shaded data value box shows option not available.

ADDRESS 2423

SYSTEM OPTIONS

DATA ENTRIES

RIGHT

OPTION

1 Enable ACM Access

2 RESERVED

3 Enable TCP/IP Communications

4 TCP/IP Panel/Site Initiated Functions

5 RESERVED

6 RESERVED

7 RESERVED

8 Enable Keypad Blanking

EMERGENCY FREE ACCESS (ADDRESS 4080)

ENABLE ACM OPTION:

1. Select the Emergency Free Access

Zone Number (001-048) and enter corre-

sponding address location at right.

2. Pres s U or D to save.

ADDRESS 4080

[Default = 000]

Emergency

Free Access

Zone Number

ACM OPTIONS

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 42 WI818G 10/05

[Default = blank (•) blank (•) from address 2471-2502

Default = blank (•) 1 from address 2455-2462

Default = blank (•) 2 from address 2463-2470]

USER AREA OPTIONS (ADDRESS 2455-2502)

USER AREA OPTIONS

USER NUMBER

AREAS 1  2

A1 A2

1 2

1 2455 ON

2 2456 ON

3 2457 ON

4 2458 ON

5 2459 ON

6 2460 ON

7 2461 ON

8 2462 ON

9 2463 ON

10 2464 ON

11 2465 ON

12 2466 ON

13 2467 ON

14 2468 ON

15 2469 ON

16 2470 ON

17 2471

18 2472

19 2473

20 2474

21 2475

22 2476

23 2477

24 2478

25 2479

26 2480

27 2481

28 2482

29 2483

30 2484

31 2485

32 2486

33 2487

34 2488

35 2489

36 2490

37 2491

38 2492

39 2493

40 2494

41 2495

42 2496

43 2497

44 2498

45 2499

46 2500

47 2501

48 2502

ADDR

USER AREA OPTIONS:

1. Each address corresponds to a specific User, numbered 1-48. For each User, select the desired Area by marking the

desired Area number (1 or 2) in the above table.

2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format.

3. Pres s U or D to save.

NOTE: See Direct Address Programming Example on page 15.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 43

WI818G 10/05

EZM GROUP OPTIONS (ADDRESS 2555-2576)

Default depends on Easy Menu questions:

"# OF ZNS IN AREA1"

and

"# OF ZNS IN AREA2"

For example, If 32 zones are used, then all 6 groups will be automatically enabled.

If only 8 zones are used, then groups 1-6 will be automatically disabled.

ADDRESS 2555

EZM Group 1

ZONES 9-12

ADDRESS 2556

EZM Group 2

ZONES 13-16

ADDRESS 2557

EZM Group 3

ZONES 17-20

ADDRESS 2558

EZM Group 4

ZONES 21-24

ADDRESS 2559

EZM Group 5

ZONES 25-28

ADDRESS 2560

EZM Group 6

ZONES 29-32

NOTE: Zones 1-8 are included in the control panel and Zones 9-32 (Groups 1-6) are EZM Zones (either Wireless or

Hardwired). Zones 33-48 are wireless only.

EZM TYPE

DATA

ENTRIES

RIGHT

OPTION

blank (•) Not used (No

EZM present)

1 4-Zone EZM

EZM GROUP OPTIONS: Up to 6 Groups of 4 Zones each may be programmed depending on the

number of zones used and which EZM modules are connected. Each group represents 4 zones.

1. Select EZM type from the table shown.

2. Enter either blank (•) or "1" in corresponding address locations above.

3. Press U or D to save

EZM PGM ARMED TERMINAL CONTROL: For each zone group select the area(s) which, when armed, will activate the PGM Lug

on the corresponding EZM modules. Each zone group corresponds to 4 zones. If 8-Zone EZMs are used, each one is treated as

TWO zone groups. NOTE: Lug goes ACTIVE (low) when EITHER selected area is armed. When activated, the PGM Lug goes

negative (to ground).

1. Select the desired group number.

2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format. NOTE: See Direct Address

Programming Example on page 15.

3. Press U or D to save.

EZM GROUP OPTIONS

GROUP

NUMBER

EZM PGM TERMINAL CONTROL

ADDR A1 A2 A3 A4 A5 A6 A7 A8

1 2 3 4 5 6 7 8

1 2577

2 2578

3 2579

4 2580

5 2581

6 2582

[Default = blank (•) blank (•) from address 2577-2582]

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 44 WI818G 10/05

AREA ARMING OPTIONS (ADDRESS 2650-2651)

PRIORITY AREA ARMING:

1. Select the desired arming area.

2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format. NOTE: See Direct Address

Programming Example on page 15.

3. Press U or D to save.

NOTE: Dark shaded data value box shows option not available.

REMOTE ACCESS LOGGING (ADDRESS 3184)

REMOTE ACCESS LOGGING: Enable logging of every keypad access event.

1. Select the desired option entering the option number (1-7) for each digit.

2. Enter corresponding option number in address location.

3. Press U or D to save.

AREA ARMING OPTIONS & REMOTE ACCESS LOGGING

3184 System Options - Enable Keypad

Default Option

OFF 1 Enable Keypad 1

OFF 2 Enable Keypad 2

OFF 3 Enable Keypad 3

OFF 4 Enable Keypad 4

OFF 5 Enable Keypad 5

OFF 6 Enable Keypad 6

OFF 7 Enable Keypad 7

OFF 8 Enable Keypad 8

ARMING AREA

PRIORITY AREA

ARMING

A1 A2

1 2

1 2650

2 2651

[Default = blank (•) blank (•) from address 2650-2651]

ADDRESS

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 45

WI818G 10/05

AREA OUTPUT CONTROL OPTIONS (ADDRESS 2700-2739)

AREA OUTPUT TURNS OFF UPON DISARM: Select options for any of the 5 Outputs per area when disarming a particular area.

1. Select the desired option.

2. Enter the corresponding Area number in each the address location, in Binary (Bit) Format. NOTE: See Direct Address

Programming Example on page 15.

3. Press U or D to save.

AREA OUTPUT CONTROL

OUTPUT SILENCED (TURNED OFF)

DISARMING AREA

1 TURNS OFF

AREA OUTPUT

ADDR A1 A2

1 2

Burglary Output 2700 ON ON

Pulsed Burg. Output 2708 ON ON

Fire Output 2716

Reset Relay 2724

Auxiliary Relay 2732

[Default = Noted above with "ON"]

OUTPUT SILENCED (TURNED OFF)

DISARMING AREA

2 TURNS OFF

ADDR A1 A2

1 2

Burglary Output 2701 ON ON

Pulsed Burg. Output 2709 ON ON

Fire Output 2717

Reset Relay 2725

Auxiliary Relay 2733

[Default = Noted above with "ON"]

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 46 WI818G 10/05

RF RECEIVERS & SUPERVISORY TIMER OPTIONS (ADDRESS 3776 & 3760-3775)

RF RECEIVERS: Up to 2 RF Receivers may be programmed. NOTE: This

adds wireless capability to the system, increasing up to 48 the number of zones.

1. Select the number of receivers (1-2).

2. Enter the corresponding decimal number (1-2) into the right-most loca-

tion. Press U or D to save.

RF RECEIVERS & SUPERVISORY TIMER OPTIONS

DATA

ENTRIES

RF

RECEIVER(S)

0 None

1 1

2 2

Default Number of Receivers = 0

Number of RF

Receivers 0 0

ADDRESS 3776

LEFT RIGHT

blank (•) blank (•)

blank (•) 1

blank (•) 2

blank (•) 3

blank (•) 4

blank (•) 5

blank (•) 6

blank (•) 7

blank (•) 8

blank (•) 9

blank (•) 0

blank (•) B

blank (•) C

blank (•) D

blank (•) E

blank (•) F

1 blank (•)

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

1 0

1 B

1 C

1 D

1 E

1 F

2 blank (•)

2 1

2 2

2 3

2 4

2 5

DATA ENTRIES DELAY

0 min.

10 min.

20 min.

30 min.

40 min.

50 min.

60 min.

70 min.

80 min.

90 min.

100 min.

110 min.

120 min.

130 min.

140 min.

150 min.

160 min.

170 min.

180 min.

190 min.

200 min.

210 min.

220 min.

230 min.

240 min.

250 min.

260 min.

270 min.

280 min.

290 min.

300 min.

310 min.

320 min.

330 min.

340 min.

350 min.

360 min.

370 min.

RF SUPERVISORY TIMERS

LEFT RIGHT

2 6

2 7

2 8

2 9

2 0

2 B

2 C

2 D

2 E

2 F

3 blank (•)

3 1

3 2

3 3

3 4

3 5

3 6

3 7

3 8

3 9

3 0

3 B

3 C

3 D

3 E

3 F

4 blank (•)

4 1

4 2

4 3

4 4

4 5

4 6

F F

DATA ENTRIES DELAY

380min.

390 min.

400 min.

410 min.

420 min.

430 min.

440 min.

450 min.

460 min.

470 min.

480 min.

490 min.

500 min.

510 min.

520 min.

530 min.

540 min.

550 min.

560 min.

570 min.

580 min.

590 min.

600 min.

610 min.

620 min.

630 min.

640 min.

650 min.

660 min.

670 min.

680 min.

690 min.

700 min.

2550 min. = 42

Hr., 30 min.

RF SUPERVISORY TIMERS RF SUPERVISORY TIMERS: RF Supervisory Timers may be

programmed for each type of transmitter used. A transmitter will

send a transmission every time it is tripped, when there is NO

activity, the transmitter sends a status transmission about once

an hour. If the receiver does NOT receive ANY signal (a trip or a

status) from a transmitter in the time specified for transmitter

type, a system trouble “E-04-NN” will be displayed at the keypad.

1. Select timer delay from the table shown. Timers are

programmed in increments of 10 minutes each. Valid

entries are (•)8-FF (80 minutes-2550 min) (2550 minutes =

42 hr,30 min).

WARNING: Timers have uncertainty of +/-30 minutes.

2. Enter in corresponding address locations above (left

and right digits).

3. For a desired timer not listed do the following:

A. Choose a desired timer (intervals of 10),

ex: 1440 min. (24 Hours)

B. Divide it by 10, ex: 1440/10 = 144

C. Divide it by 16

6 Quotient Left Digit

16 100

96

4 Remainder Right Digit

NOTE: These timers apply only to Supervised RF

Transmitters (see RF Transmitters in Easy Menu Driven Mode

Programming).

[Default = blank (•) 8 from address 3760-3767 (80 minutes)]

LEFT ADDR RIGHT

3760

3761

3762

3763

3764

3765

3766

3767

ADDRESS

3760-3767

RF SUPERVISORY

TIMER

RF TRANSMITTER

Type 0 Window/Door, 2 Pt.

Type 1 Window/Door, 2 Pt.

Type 2 Window/Door, 2 Pt.

Type 3 Window/Door, 2 Pt.

Type 4 Window/Door, 4 Pt.

Type 5 PIR

Type 6 PIR

Type 7 Smoke Detector

[Default = blank (•) 8 from address 3768-3775 (80 minutes)]

LEFT ADDR RIGHT

3768

3769

3770

3771

3772

3773

3774

3775

ADDRESS

3768-3775

RF SUPERVISORY

TIMER

RF TRANSMITTER

Type 8 Smoke Detector

Type 9 Keyfob

Type A Dual Tech.

Type B Keyfob

Type C Window/Door, 4 Pt.

Type D PIR

Type E Smoke Detector

Type F Napco Glass Break

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 47

WI818G 10/05

EXTERNAL RELAY CONTROL / RELAYS 1-24 (ADDRESS 3778-3801 & 2800-2895)

ADDRESS 3778 & 2800-2803 (RELAY/entry 1)

3778 2800 2801 2802 2803

L R L R L R L R

ADDRESS 3779 & 2804-2807 (RELAY/entry 2)

3779 2804 2805 2806 2807

L R L R L R L R

ADDRESS 3780 & 2808-2811 (RELAY/entry 3)

3780 2808 2809 2810 2811

L R L R L R L R

ADDRESS 3781 & 2812-2815 (RELAY/entry 4)

3781 2812 2813 2814 2815

L R L R L R L R

ADDRESS 3782 & 2816-2819 (RELAY/entry 5)

3782 2816 2817 2818 2819

L R L R L R L R

ADDRESS 3783 & 2820-2823 (RELAY/entry 6)

3783 2820 2821 2822 2823

L R L R L R L R

ADDRESS 3784 & 2824-2827 (RELAY/entry 7)

3784 2824 2825 2826 2827

L R L R L R L R

ADDRESS 3785 & 2828-2831 (RELAY/entry 8)

3785 2828 2829 2830 2831

L R L R L R L R

ADDRESS 3786 & 2832-2835 (RELAY/entry 9)

3786 2832 2833 2834 2835

L R L R L R L R

ADDRESS 3787 & 2836-2839 (RELAY/entry 10)

3787 2836 2837 2838 2839

L R L R L R L R

ADDRESS 3788 & 2840-2843 (RELAY entry 11)

3788 2840 2841 2842 2843

L R L R L R L R

ADDRESS 3789 & 2844-2847 (RELAY/entry 12)

3789 2844 2845 2846 2847

L R L R L R L R

ADDRESS 3790 & 2848-2851 (RELAY/entry 13)

3790 2848 2849 2850 2851

L R L R L R L R

ADDRESS 3791 & 2852-2855 (RELAY/entry 14)

3791 2852 2853 2854 2855

L R L R L R L R

ADDRESS 3792 & 2856-2859 (RELAY/entry 15)

3792 2856 2857 2858 2859

L R L R L R L R

ADDRESS 3793 & 2860-2863 (RELAY/entry 16)

3793 2860 2861 2862 2863

L R L R L R L R

ADDRESS 3794 & 2864-2867 (RELAY/entry 17)

3794 2864 2865 2866 2867

L R L R L R L R

ADDRESS 3795 & 2868-2871 (RELAY/entry 18)

3795 2868 2869 2870 2871

L R L R L R L R

ADDRESS 3796 & 2872-2875 (RELAY/entry 19)

3796 2872 2873 2874 2875

L R L R L R L R

ADDRESS 3797 & 2876-2879 (RELAY/entry 20)

3797 2876 2877 2878 2879

L R L R L R L R

(•)

ADDRESS 3798 & 2880-2883 (RELAY/entry 21)

3798 2880 2881 2882 2883

L R L R L R L R

(•)

ADDRESS 3799 & 2884-2887 (RELAY/entry 22)

3799 2884 2885 2886 2887

L R L R L R L R

(•)

ADDRESS 3800 & 2888-2891 (RELAY/entry 23)

3800 2888 2889 2890 2891

L R L R L R L R

(•)

ADDRESS 3801 & 2892-2895 (RELAY/entry 24)

3801 2892 2893 2894 2895

L R L R L R L R

(•)

EXTERNAL RELAY CONTROL

[Default = blank (•) blank (•) from address 3778-3801 & 2800-2895]

Continued

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 48 WI818G 10/05

EXTERNAL RELAY CONTROL

STEP 2: AREA OPTIONS: Each relay/entry can be assigned to Area 1 or 2 or both areas.

Select the area from Table 2 (shown on next page); enter in corresponding left and right digit

address locations.

RELAY EVENT OPTIONS

RELAY # AREA Timeout Event ID COND.

L R L R L R L R

(•) (•)

To program, follow the 5 steps below:

STEP 1: RELAY # OPTIONS: Each relay/entry can be assigned to any of the

24 available external relays from Relay Module RM3008. Multiple entries can

drive the same External Relay.

Select the relay number from Table 1 (shown on next page); enter in

corresponding left and right digit address locations.

Note: Entries 01-24 correspond to relays 1 through 24. If entries are zero, zero

(00), then relay number is identical to the relay/entry address table number, in

the selected address table(s) above.

STEP 3: TIMEOUTS: Each relay event can be assigned a timeout depending on Alarm Type option.

If Alarm Type is selected for timeout in minutes or seconds, enter the 3-digit timeout duration in corre-

sponding address location. To choose seconds or minutes, see step 5A below. 254 is maximum entry.

Continued

STEP 4: EVENT ID CODES: Each relay event can be assigned any of the available event IDs from the table.

Select 2-digit Event ID from Table 4 (see page 50); enter in corresponding address locations (left and right digit).

STEP 5: RELAY EVENT CONDITION OPTIONS: Each relay event can be assigned an alarm type; and an activation

condition; also, select a timeout type for each.

5A. Select Alarm Type and Timeout Type from Table 5A (see page 51); enter in corresponding address location (left digit).

NOTE: Select Timeout from Step 3.

5B. Select Activation from from Table 5B (see page 51); enter in corresponding address location (right digit).

Step

4

Step

5

Step

1

Step

2

Step

3

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 49

WI818G 10/05

EXTERNAL RELAY CONTROL

For a desired relay not listed:

A. Choose a desired relay, ex: 60

B. Divide it by 16

3 Quotient Left Digit

16 60

48

C Remainder Right Digit

TABLE 2 (AREAS 1-2)

AREAS CONTROLLING RELAY

SHUTOFF ON DISARM

RIGHT DATA

ENTRY

AREA 1 AREA 2

blank (•) NONE

1 Y

2 Y

3 Y Y

Note: “Y” indicates option is enabled.

TABLE 1

RELAY MAPPING

DATA ENTRIES RELAY #

LEFT RIGHT

blank (•) blank (•) None *

blank (•) 1 1

blank (•) 2 2

blank (•) 3 3

blank (•) 4 4

blank (•) 5 5

blank (•) 6 6

blank (•) 7 7

blank (•) 8 8

blank (•) 9 9

blank (•) 0 10

blank (•) B 11

blank (•) C 12

blank (•) D 13

blank (•) E 14

blank (•) F 15

1 blank (•) 16

1 1 17

1 2 18

1 3 19

1 4 20

1 5 21

1 6 22

1 7 23

1 8 24

* Note: [blank (•) blank (•)] option affects the

relay with the same entry number. All other

options affect the relay number specified. Ex:

Suppose Relay/Entry 1 is mapped to External

Relay 1 and Relay/Entry 2 is mapped to

External Relay 24. The data entries are as

follows: Address 3778 = [blank (•) blank (•)] and

Address 3779 = [1C].

RELAY EVENT OPTIONS

RELAY # AREA TIMEOUT EVENT ID COND.

See

Table 1 below

See

Table 2 below

See

Table 3 below

See

Table 4 on page 50

See

Tables 5A & 5B on

page 51

Areas

1-2

Continued

TIMEOUTS: Each relay event can be

assigned a timeout depending on Alarm Type

option.

If Alarm Type is selected for timeout in

minutes or seconds, enter the 3-digit time-

out duration in corresponding address

location. To choose seconds or minutes,

see step 5A on page 51. Maximum entry

is 254.

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 50 WI818G 10/05

EXTERNAL RELAY CONTROL

STEP 4: EVENT ID CODES: Each relay event can be assigned any of the available event IDs from the table.

Select 2-digit Event ID from Table 4 (below); enter in corresponding address locations (left and right digit).

Continued

TABLE 4

EVENT ID CODES

DATA ENTRIES OPTION

LEFT RIGHT

blank (•) blank (•) Area 1 Arm

blank (•) 1 Area 2 Arm

blank (•) 8 Zone 1

blank (•) 9 Zone 2

blank (•) 0 Zone 3

blank (•) B Zone 4

blank (•) C Zone 5

blank (•) D Zone 6

blank (•) E Zone 7

blank (•) F Zone 8

1 blank (•) Zone 9

1 1 Zone 10

1 2 Zone 11

1 3 Zone 12

1 4 Zone 13

1 5 Zone 14

1 6 Zone 15

1 7 Zone 16

1 8 Zone 17

1 9 Zone 18

1 0 Zone 19

1 B Zone 20

1 C Zone 21

1 D Zone 22

1 E Zone 23

1 F Zone 24

2 blank (•) Zone 25

2 1 Zone 26

2 2 Zone 27

2 3 Zone 28

2 4 Zone 29

2 5 Zone 30

2 6 Zone 31

2 7 Zone 32

2 8 Zone 33

2 9 Zone 34

2 0 Zone 35

2 B Zone 36

2 C Zone 37

2 D Zone 38

2 E Zone 39

2 F Zone 40

3 blank (•) Zone 41

3 1 Zone 42

3 2 Zone 43

3 3 Zone 44

3 4 Zone 45

3 5 Zone 46

3 6 Zone 47

3 7 Zone 48

C blank (•) Area 1 disarm

C 1 Area 2 disarm

6 8 Area 1 Keypad Ambush

6 9 Area 1 Keypad Panic

6 0 Area 1 Keypad Fire

6 B Area 1 Keypad Medical

6 C Keypad Tamper

6 D Area 1 Fail to Open

6 E Area 1 Fail to Close

7 blank (•) Area 2 Keypad Ambush

7 1 Area 2 Keypad Panic

7 2 Area 2 Keypad Fire

7 3 Area 2 Keypad Medical

7 5 Area 2 Fail to Open

7 6 Area 2 Fail to Close

0 8 Test Timer

0 0 Bus Fail

0 B Guarded RAM Fail

0 C Low Battery

0 D AC Fail

0 E EZM Tamper

0 F Sensor Watch

B blank (•) Telco Fault

B 8 Digital Dialer Test

B 9 RESERVED

B B Service Message

B C Program Change

B D RF Receiver Trouble

B E Transmitter Tamper

B F Transmitter Trouble

D blank (•) Keypad Fail

D 1 EZM Fail

D 2 Quickloader Device Control

D 3 System Shutdown

D 4 Quickloader Keypad Reset

D 5 General System Alarm

D 8 Area 1 General System Alarm

D 9 Area 2 General System Alarm

F blank (•) Relay Group 1

F 1 Relay Group 2

F 8 Area 1 Entry Delay

F 9 Area 2 Entry Delay

NOTE: Keypad Tamper must be enabled in

UL installations using jumper op-

tion on keypad.

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 51

WI818G 10/05

EXTERNAL RELAY CONTROL

NUMBER OF RELAY BOARD MODULES (ADDRESS 3777)

[Default = blank (•) blank (•)]

LEFT RIGHT

blank (•)

ADDRESS 3777

Number of Relay

Board Modules

DATA

RIGHT

blank (•)

1

2

3

Relay Board Module(s)

None

1

2

3

RELAY BOARD MODULES: Up to 3 External Relay Board

Modules (RM3008) may be programmed.

1. Select the number of relay modules from the table

shown.

2. Enter in corresponding right digit address location

shown (left digit is not used).

STEP 5: RELAY EVENT CONDITION OPTIONS: Each relay event can be assigned an alarm type; and an activation condition; also, select a

timeout type for each.

5A. Select Alarm Type and Timeout Type from Table 5A (below); enter in corresponding address location (left digit). NOTE: Select Timeout from

Step 3.

5B. Select Activation from from Table 5B (below); enter in corresponding address location (right digit).

TABLE 5A

RELAY EVENT

ALARM TYPE OPTIONS

LEFT DATA

ENTRIES

ALARM

TYPE

TIMEOUT

TYPE

blank (•) Burglary Minutes

1 Fire Minutes

4 Day Zone Minutes

8 Burglary Seconds

9 Fire Seconds

C Day Zone Seconds

TABLE 5B

RELAY EVENT

ACTIVATION CONDITIONS

RIGHT DATA ENTRIES OPTIONS

1 Alarm

2 Restore

3 Trouble

4 Trouble Restore

5 Follows Open Zone

6 Follows Shorted Zone

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 52 WI818G 10/05

DIRECT ADDRESS PROGRAM MODE--USER PROGRAM MODE

USER PROGRAM MODE

PRELIMINARY INFORMATION

The User Program Mode is covered in detail in the operating instructions for the keypad in use.

Only Keypad #1 may be used for programming, however this keypad may be located in either area.

The Program Mode cannot be accessed while the communicator is transmitting except during the first three minutes after power-

up.

After entering codes or data, press the save U button. Data will not be stored into memory unless this button is pressed.

If the keypad is in the Program Mode and no activity is detected for longer than 4 minutes, a steady tone will sound.

Press the C button to silence the sounder and exit the User Program Mode.

If a GEM-RP2ASe2/GEM-K2AS keypad is used, configure address jumpers as Keypad #1 (See WI1184).

NOTE: For ease of programming, it is recommended that a GEM K1CA (or GEM-RP1CAe2) be used as Keypad #1. A new GEM-

K1CA and a new GEM-RP1CAe2 are automatically configured as Keypad #1. See Keypad Configuration Mode.

SYSTEM RESET OPTIONS (ADDRESS 4091-4093)

Clear Dealer Program (Erases Dealer Program)

This erases the dealer program. Use this feature to start

a customized default program.

Access address 4091, then press the J or U button. Data entry is not

allowed.

NOTE: Enter Easy Menu Driven Program Mode to program system

again.

GEM-RP1CAe2/GEM-K1CA Keypad

4091 XX

GEM-RP2ASe2 Keypad

4091XX

Cold Start (Erases Entire Program)

This erases the entire program (codes, schedules,

foreign language configuration, etc), leaving the panel

as it came right out of the box.

Access address 4093, then press the J or U button. Data entry is not

allowed.

NOTE: Some features (schedules, language configuration) can only be

re-programmed with the Downloading Software.

GEM-RP1CAe2/GEM-K1CA Keypad

4093 XX

GEM-RP2ASe2 Keypad

4093XX

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 53

WI818G 10/05

ACCESSING USER PROGRAM MODE

1. Press EEEEEE R

2. Press Q Until “ACTIVATE PROGRAM Y/N” appears on LCD screen.

3. Press P To Enter User Program Mode

4. Press C To Exit User Program Mode when finished

New Panel (Default User Code = 123)

Existing Panel (Any Code with User Program Option Enabled)

USER CODES

Up to 48 User Codes may be programmed.

NOTE: In this mode, only the code is pro-

grammable; the accompanying Area Options

must be programmed in the Dealer Program

Mode. By default, User 1 is enabled in Area 1

and 2; Users 2-8 are enabled in Area 1, Users

9-16 are enabled in Area 2; Users 17-48 are

not enabled in any areas (see page 10).

Use the R button to place the cursor

over the User Number.

Enter a User Number (01–48) using the number buttons. The cursor will then advance to the User Code and read the existing

code, if any.

Enter the new User Code using the number buttons (0-9). If an old code is displayed, program over it. To erase the digit at the

cursor, press G 0 button.

Press the U button to save the code in memory.

Repeat this procedure for each user. To proceed to Zone-Description programming, press the NEXT button or the PRIOR but-

ton.

GEM-K1CA Keypad (Direct Entry)

Enter user code

U01 123

USER PROGRAM MODE

Programming User Codes with GEM-K1CA Keypad

To Program User Codes

1. Set Cursor Position using the

R button.

2. Enter 2-digit User Number (01-

48) directly using number but-

tons (0-9).

3. Enter Code (1-6 digits) directly

using number buttons (0-9).

4. Press the U button to save

each code.

NOTE: Press G 0 button to clear character at cursor.

To continue press P or Q button.

GEMINI

Enter user code

U01 123 - -

ARMED

COMPUTERIZED SECURITY SYSTEM

STATUS

R 1 2 3

B 4 5 6

C 7 8 9 0

U

NEXT/YES

P

PRIOR/NO

Q

AREA

G

User Code NOT USED

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 54 WI818G 10/05

ZONE DESCRIPTIONS (GEM-RP1CAE2 / GEM-K1CA KEYPADS)

Enter an identifying description for each zone. Characters are selected by

pressing keypad buttons multiple times, "Cell Phone" style. Buttons 1

through 9 plus 0 and G are used, as per the following table:

Press [A] to move cursor right.

Press [B] to move cursor left.

Notes:

1. After releasing the number button for 1 second, the character will be accepted and the cursor advanced to the

right.

2. After releasing the number button, if a new number button is pressed before the 1 second window expires, the cur-

rent character will be accepted and the cursor automatically advanced to the right. The first of the 4 characters of

this new number button will be displayed.

3. To erase an existing entry, use [A] or [B] to move the cursor below the character to be changed. Enter a

new character to overwrite the old.

4. To generate lowercase characters, the [G] button must be pressed and held down while pressing the number

button. If the [G] button is released during the 1 second window, the current character will change to upper-

case. Press U to save.

To proceed to the next description, place the cursor under the Zone Number (e.g. “1”) and press the number that corre-

sponds to the zone. Repeat this procedure until all zones have been programmed. After programming the user codes,

press the NEXT button to proceed.

Enter Date (Press the (R) button to set cursor.)

Enter the current date in the format MM/DD/YY, where MM = the month

(01–12); DD=the day (01–31); and YY=the year. Press U to save. Press

NEXT button to proceed.

Enter Time (Press the (R) button to set cursor.)

Enter the current time in the format HH:MMA/P, where HH=hours (01–12);

MM=minutes (00–59). Select Am or Pm by pressing any number button,

then press U once again to save.

NOTE: To enter the date and time, GEM-RP1CAe2/GEM-K1CA keypad (version 6 or greater) must be used and

“Enable Keypad Time/Date Display” (Address 3874) must be enabled.

(Direct Entry)

Enter Date

( / / )

(Direct Entry)

Enter Time

( : )

USER PROGRAM MODE

(Direct Entry)

01-

PRESS: CHARACTERS DISPLAYED

IN SEQUENCE

HOLD G

AND PRESS:

CHARACTERS DISPLAYED

IN SEQUENCE

[1] ABC1 [1] abc1

[2] DEF2 [2] def2

[3] GHI3 [3] ghi3

[4] JKL4 [4] jkl4

[5] MNO5 [5] mno5

[6] PQR6 [6] pqr6

[7] STU7 [7] stu7

[8] VWX8 [8] vwx8

[9] YZ90 [9] yz90

[0] (SPACE) - . ( ) , / : ? # [0] (International Characters)

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 55

WI818G 10/05

KEYPAD CONFIGURATION MODE

This section will focus on configuring the GEM-RP1CAe2/GEM-K1CA Keypads. If there is more than one keypad in the system, only

Keypad No. 1 may be used for programming.

KEYPAD INSTALLATION

Two types of keypads may be used with the GEM-P3200: the GEM-RP1CAe2/GEM-K1CA. Each must be assigned an address

number (1–7) and each requires its own configuration procedure (see CONFIGURING THE KEYPADS, which follows, and DIRECT

ADDRESS KEYPAD AREA OPTIONS). At least 1 keypad must be used; only 1 is required for a single-area Commercial Burglary

installation.

GEM-RP1CAe2/GEM-K1CA - is a 2-line combination fire/burglary/access keypad capable of supporting 4 EZM zones and a

PGM output. The GEM-RP1CAe2 or GEM-K1CA is recommended for use as Keypad #1. See "Important Note" on page 2

for more information regarding the various buttons on the GEM-RP1CAe2/GEM-K1CA keypads.

CONFIGURING THE KEYPADS

A total of up to 7 keypads may be connected to the panel.

Configuring the GEM-RP1CAe2/GEM-K1CA Keypad

Each GEM-RP1CAe2/GEM-K1CA keypad must be configured for (a) keypad tactile beep; (b) entry sounder; (c) keypad address; (d)

compatibility number; (e) EZM address; and (f) zone response.

To enter the Keypad Configuration Mode:

1. Move jumper JP1 (located in the center of the control panel board) from Pins 1-2 (top two) to Pins 2-3 (bottom

two). NOTE: See Wiring Diagram on page 68.

2. After about 15 seconds, the display will read “XX OUT OF SYSTEM”, where XX indicates the keypad address.

3. Press 11123 R and proceed as follows. (Repeat the following procedure for

all keypads).

Keypad Tactile Beep

Upon entering the Keypad Configuration Mode, “KEYPAD BEEP ON” will be displayed,

indicating that the tactile beep, which sounds when any button is pressed, is on.

To turn off the tactile beep, press the U button (the U button will toggle the tac-

tile beep on and off). Press R to continue or press C to exit.

Entry Sounder

To turn off the keypad entry sounder during entry time, press U (the U button

will toggle the entry sounder on and off). Press R to continue or press

C to exit.

Keypad Address

If more than one keypad is installed, each must be assigned a unique keypad

address (that is, no two keypads may be numbered alike):

Keypads must be numbered consecutively (missing numbers are not permitted)

Only Keypad No. 1 may be used for programming.

To assign the keypad number, proceed as follows:

1. Enter the assigned keypad number 01–07, then press U to save. A valid

number will be acknowledged by a short beep; an invalid number will be re-

jected by a long beep.

2. Press R to continue or press C to exit.

Keypad Beep

ON

NORMAL

KEYPAD

CONFIGURE

R

COMPUTERIZ ED SECURITY SYS TEM

GEMINI

ARMED

STATUS

SYSTEM ARMED

01/01/97 12:00AM

12

4

3

56

7890

A

B

C

DE

F

G

NEXT/Y ES

PRIOR/NO

AREA

# OF ZONES IN AREA 1

ENTER # ZONES X X

# OF ZONES IN AREA

ENTER # ZONES XX

Entry Sounder

ON

Keypad Address

01

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 56 WI818G 10/05

Compatibility Number

A 4-digit Compatibility Number, if programmed, will restrict this keypad to

work on a panel programmed with a matching number.

1. Enter a 4-digit number

2. Press U to save. Press the R button to continue or press the

C button to exit.

EZM Address

The keypad's internal EZM (Expansion Zone Module) may be utilized to

provide four additional wired zones. Whether used alone or in conjunction

with optional GEM-EZM series modules or other keypad EZMs, it must be

assigned a unique address (or Group number, see Keypad Programming

Workbook) similar to its keypad address. If no other EZMs are to be used, designate the keypad as Group “01” at the

“EZM ADDRESS 00” display. In multiple-EZM systems, enter an assigned group number “01” through “06”. (Each

EZM must have a unique assigned group number, starting with “01” and proceeding consecutively.) Press the R

button to continue or press the C button to exit.

Zone Response

The normal loop response of each keypad expansion zone is 750mS, how-

ever the response time of any zone can be reduced to 50mS as follows.

1. Of the following, circle the number(s) in parentheses associated with the

zone(s) to be changed: Zone 1=(1); Zone 2=(2); Zone 3=(4); Zone 4=(8)

2. Add up the circled numbers.

3. At the keypad, enter the sum as a two-digit number “01” through “15” on the display, then press U.

Example. Change Zones 2, 3 and 4 to 50mS response.

1. Circle numbers for Zones 2, 3 and 4: (2), (4) and (8).

2. Add up the circled numbers: 2 + 4 + 8 = 14.

3. Enter “14” at the keypad, then press the U button.

Press the R button to continue or press the C button to exit.

Program Control Message

A code-keypad association can be programmed such that when the code is

entered at a specific keypad, a PGM Lug will be activated for 7 seconds,

and a selected message will be displayed on this keypad. Six different pro-

gram control messages can be selected (0-6) as displayed in the following table:

1. Enter a message number

2. Press U to save.

3. Press the R button to continue (the display will loop back through selections, for changes) or press the

C button to exit the Keypad Configuration Mode (display will read “01 OUT OF SYSTEM”).

4. Replace Jumper JP1 across Pins 1–2 (top two).

New

Compat # 0000

EZM Address

01

Zone Response

00

Program Control

Message # ?

0 (No Message)

1 **Enter Now**

2 Door Control

3 Gate Control

4 Light Control

5 Control #1

6 Control #2

Program Control Message

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 57

WI818G 10/05

ALPHABETICAL INDEX

ABORT DELAY ADDRESS 2406, 19

ABORT DELAY ZONE OPTION, 30, 31, 32

AC FAIL REPORT DELAY ADDRESS 2408, 19

ACCESS CONTROL (PANEL) ON AUX. OUTPUT ADDRESS 2418, 34

ACCESS CONTROL OPTIONS, 10

ACCESSING DEALER PROGRAM MODE, 5

ACCESSING USER PROGRAM MODE, 53

ACM DOOR #1 AREA (HEX) (ADDRESS 2425-2431), 40

ACM DOOR AREA OPTIONS (ADDRESS 2784-2787), 39

ACM GLOBAL FLAGS (ADDRESS 2780), 38

ACM SCHEDULED FREE ACCESS (ADDRESS 4072-4075), 39

ACM SYSTEM OPTIONS (ADDRESS 2423), 41

ACM TIMEOUTS (ADDRESS 2782-2783), 38

ACM ZONE OPTIONS (ADDRESS 2740-2769), 38

ACTIVATE DOWNLOAD FUNCTION, 4

ADDING WIRELESS CAPABILITY, 46

ADDRESS MODE DISPLAYS, 15

ALARM ON DAY ZONE ZONE OPTION, 30, 31, 32

ALARM/TROUBLE REPORTING CODES (ADDRESS 3880-3881), 35

ALARM/TROUBLE REPORTING CODES ADDRESS 0859-0862, 24

AMBUSH CODE ADDRESS 0495, 20

ANSWER ON RING NUMBER ADDRESS 4089, 22

AREA ARMING OPTIONS (ADDRESS 2650-2651), 44

AREA ASSIGNMENT & KEYPAD TYPE, 37

AREA OUTPUT CONTROL OPTIONS (ADDRESS 2700-2739), 45

AREA SYSTEM EVENT/TROUBLE, 29

AREA SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS 1120-

1137), 29

AUTHORITY LEVEL, 10

AUTO BELL TEST ON ARMING ADDRESS 2418, 34

AUTO BYPASS RE-ENTRY ZONES, 7

AUTO DISARM REARM DELAY ADDRESS 4083, 20

AUTO DOWNLOAD ID NO. ADDRESS 1023, 22

AUTO RESET AFTER BURG. OUTPUT TIMEOUT ADDRESS 2418,

34

AUTO RESET ZONE OPTION, 30, 31, 32

AUTO-BYPASS RE-ENTRY ZONE OPTION, 30, 31, 32

AUTO-BYPASS ZONE OPTION, 30, 31, 32

AUTOMATIC INTERIOR BYPASS/EASY EXIT ADDRESS 2421, 35

AUX OUTPUT ACTIVATED ON ALARM ZONES, 7

AUX. OUTPUT ACCESS CONTROL TIMEOUT ADDRESS 2402, 19

AUX. OUTPUT TIMEOUT ADDRESS 2401, 20

AUXILIARY RELAY, 28, 29

AUXILIARY RELAY ZONE OPTION, 30, 31, 32

BACKUP REPORT ON TELCO 2 ADDRESS 1027, 25

BINARY (BIT) FORMAT, 15

BIT FORMAT, 15

BURG KEYPAD TYPE, 37

BURG. ALARM OUTPUT TIMEOUT ADDRESS 2403, 20

BURG. ALARM OUTPUT ZONE OPTION, 30, 31, 32

BURGLARY ALARM OUTPUT, 28

BURGLARY OUTPUT, 29

CALLBACK METHOD, 4

CALLBACK TELEPHONE NO. SELECT ADDRESS 1022, 22

CALLBACK TELEPHONE NUMBER 1 AND 2, 22

CANCEL A CODE, 11

CANCEL NEXT TEST TIMER ON ANY REPORT ADDRESS 1027, 25

CANCELING A CODE, 11

CENTRAL STATION RECEIVER 1 ACCOUNT NUMBER, 9

CENTRAL STATION RECEIVER 1 FORMAT, 9

CENTRAL STATION RECEIVER 1 TELEPHONE NUMBER, 8

CHANGES FROM PREVIOUS EDITION, 2

CHANGING OR CANCELING A CODE, 11

CHIME 2 ZONE OPTION, 30, 31, 32

CHIME 2 ZONES IN AREA 1, 7

CHIME ON LUG E4 ADDRESS 2420, 35

CHIME TIME ADDRESS 2407, 19

CHIME ZONE OPTION, 30, 31, 32

CHIME ZONES IN AREA 1, 6

CLEAR DEALER PROGRAM, 14

CLEAR DEALER PROGRAM ADDRESS 4091, 52

CLEAR PROGRAM, 14

CLOSING REPORT ONLY ON COND. CLOSING (AUTO-BYP.) AD-

DRESS 2417, 34

COLD START, 14

COLD START ADDRESS 4093, 52

COMPATIBILITY NUMBER, 56

CONFIGURING THE KEYPADS, 55

CREATE A NEW CUSTOM DEFAULT PROGRAM, 5

CS AREA & SYSTEM REPORTING OPTIONS (ADDRESS 1024-

1027), 25

CS RECEIVER 1 FORMAT ADDRESS 0525, 21

CS RECEIVER 1 OPTIONS ADDRESS 0526, 21

CS RECEIVER 2 FORMAT ADDRESS 0550, 21

CS RECEIVER 2 OPTIONS ADDRESS 0551, 21

CS RECEIVER 3 FORMAT ADDRESS 0575, 21

CS RECEIVER 3 OPTIONS ADDRESS 0576, 21

CS RECEIVER FORMAT OPTIONS (ADDRESS 0520, 0521, 0525,

0526, 0550, 0551, 0575 & 0576), 21

CS RECEIVER TELEPHONE NUMBER 1-3, 22

CS RECEIVER TELEPHONE NUMBERS (ADDRESS 0527-0546,

0552-0571, 0577-0596), 22

CS REPORTING CODES (ADDRESS 0859-0883), 24

CS REPORTING CODES (ADDRESS 0870-0904), 25

CS SUBSCRIBER ID NUMBERS (ADDRESS 0650-0787), 23

CS SUBSCRIBER ID NUMBERS (ADDRESS 0790-0857), 24

CS SYSTEM REPORT OPTIONS ADDRESS 1027, 25

CS TELCO 1 SUBSCRIBER EVENT ID NUMBERS, 23

CS TELCO 1 SUBSCRIBER OPENING/CLOSING ID NUMBERS, 23

CS TELCO 2 SUBSCRIBER EVENT ID NUMBERS (BACKUP RE-

PORTING), 23

CS TELCO 2 SUBSCRIBER OPENING/CLOSING ID NUMBERS

(BACKUP REPORTING), 23

CS TELCO 3 REPORT DELAY ADDRESS 3902, 19

CS TELCO 3 SUBSCRIBER EVENT ID NUMBERS, 24

CS TELCO 3 SUBSCRIBER OPENING/CLOSING ID NUMBERS, 24

CS USER REPORTING CODES (ADDRESS 1030-1074), 27

CS ZONE REPORTING CODES (ADDRESS 0910-0957), 26

CUSTOM DEFAULT PROGRAM, 5

CUSTOMIZING A DEFAULT PROGRAM, 5

DATE, 14, 54

DAY ZONE OPEN ZONE OPTION, 30, 31, 32

DAY ZONE SHORT ZONE OPTION, 30, 31, 32

DEALER CODE, 14

DEALER PROGRAM, 5

DEALER SECURITY CODE ADDRESS 0500-0502, 20

DECIMAL FORMAT, 16

DECIMAL FORMAT DATA ENTRY, 15

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 58 WI818G 10/05

ALPHABETICAL INDEX (CONT'D)

DIALING—ROTARY OR TOUCH-TONE, 25

DIGITAL DIALER RPT ENTER/EXIT TEST MODE ADDRESS 3905, 35

DIRECT ADDRESS OVERVIEW, 15

DIRECT ADDRESS PROGRAM MODE, 15

DISABLE AC FAIL DETECTION ADDRESS 2420, 35

DISABLE ANSWERING-MACHINE DOWNLOAD ADDRESS 2419, 34

DISABLE AREA ENTRY RELAYS ADDRESS 2422, 35

DISABLE AUTO-RESET ON DAY ZONE ADDRESS 2419, 34

DISABLE AUTO-UNBYPASS ON DISARMING ADDRESS 2417, 34

DISABLE AUXOUT CLEAR ON DISARM ADDRESS 2421, 35

DISABLE CALL WAITING ON FIRST ATTEMPT ADDRESS 3905, 35

DISABLE CALLBACK DOWNLOAD ADDRESS 2419, 34

DISABLE CODE REQUIRED FOR EZ BYPASS ADDRESS 2420, 35

DISABLE CODE REQUIRED FOR FUNC. MODE LVL. 1 ADDRESS

2420, 35

DISABLE EXIT/ENTRY URGENCY TONE AT KEYPAD ADDRESS

2422, 35

DISABLE FIRE RESET ADDRESS 2415, 34

DISABLE KEYPAD FUNCTION-MODE DOWNLOAD ADDRESS 2419,

34

DISABLE KEYPAD INSTANT BUTTON ADDRESS 2420, 35

DISABLE SYSTEM TROUBLE AUDIBLE (AT KEYPAD) ADDRESS

2420, 35

DISABLE WAIT FOR HANDSHAKE ADDRESS 1027, 25

DISABLE WAIT FOR SILENCE ADDRESS 1027, 25

DISABLE ZONE FAULT SCROLLING (AUTO STATUS) ADDRESS

2421, 35

DOUBLE SWIPE TIME, 38

DOWNLOAD SECURITY CODE ADDRESS 0645-0647, 22

DOWNLOAD/CALLBACK OPTIONS (ADDRESS 4089, 0600-0619,

0625-0647, 1022 & 1023), 22

DOWNLOADING FROM A COMPUTER, 4

EASY MENU DRIVEN PROGRAM MODE, 5

EASY PROGRAM MENU, 6

EMERGENCY FREE ACCESS (ADDRESS 4080), 41

ENABLE ACCESS LOGGING INTO BURG LOG ADDRESS 2780, 38

ENABLE ACM ACCESS ADDRESS 2423, 41

ENABLE ALL-ZONE-IN-TROUBLE BYPASS ADDRESS 2417, 34

ENABLE AMBUSH IN USER ASSIGNMENT CODE TYPE ADDRESS

3905, 35

ENABLE BELL ON EXIT ERROR ADDRESS 3905, 35

ENABLE BURG OUTPUT CHIRP ON KEYFOB?, 7

ENABLE BURG. OUTPUT ON TELCO FAIL ONLY WHEN ARMED

ADDRESS 2422, 35

ENABLE BURG. OUTPUT WARNING ON ENTRY ADDRESS 2418, 34

ENABLE CANCEL REPORT TO TELCO 3 ADDRESS 3874, 35

ENABLE CARD PRESENTATION BEEP AND GREEN LED FLASH

ADDRESS 2780, 38

ENABLE CP-01 LIMITS ADDRESS 3905, 35

ENABLE DAY ZONE WATCH ADDRESS 2416, 34

ENABLE EXIT DELAY RESTART (SIA-FAR) ADDRESS 3905, 35

ENABLE EXIT-DELAY RESTART ADDRESS 2419, 34

ENABLE FACILITY CODE ADDRESS 2780, 38

ENABLE GEM-PRINT ADDRESS 3874, 35

ENABLE KEYPAD BLANKING ADDRESS 2423, 41

ENABLE KEYPAD TIME/DATE DISPLAY ADDRESS 3874, 35

ENABLE KEYPAD--REMOTE ACCESS LOGGING (ADDRESS 3184),

44

ENABLE LOCAL ALARM ON FIRST ZONE “AND” TRIP ADDRESS

2419, 34

ENABLE MANAGER’S MODE OUTSIDE OVERVIEW ADDRESS 2418,

34

ENABLE NAPCO PROPRIETARY ACCESS FORMAT ADDRESS

2780, 38

ENABLE NO EOLR ZONES, 7

ENABLE PRINTING OF ACCESS EVENTS ADDRESS 2780, 38

ENABLE REPORT EXIT ERR/RECENT CLOSE ADDRESS 3905, 35

ENABLE SET TIME/DATE MESSAGE ADDRESS 3874, 35

ENABLE SIA CP-01 FEATURES?, 8

ENABLE SMOKE DETECTOR DIRTY TROUBLE ADDRESS 2422, 35

ENABLE TCP/IP COMMUNICATIONS ADDRESS 2423, 41

ENABLE TELCO LINE FAULT TEST?, 7

ENABLE TELEPHONE LINE-FAULT TEST ADDRESS 2420, 35

ENABLE TWO-SWIPE ARMING ADDRESS 2780, 38

ENABLE USERS TO REPORT, 27

ENABLE ZONE NUMBER ON PULSE ALARM ADDRESS 0526, 21

ENABLE ZONE NUMBER ON PULSE ALARM ADDRESS 0551, 21

ENABLE ZONE NUMBER ON PULSE ALARM ADDRESS 0576, 21

ENROLL METHOD, 13

ENTER DATE, 54

ENTER DEALER PROGRAM MODE, 5

ENTER PROXIMITY CARD USERS, 12

ENTER TIME, 54

ENTER USER CODES, 10

ENTER ZONE DESCRIPTIONS, 14

ENTRY DELAY 1 ADDRESS 0001, 19

ENTRY DELAY 2 ADDRESS 0002, 19

ENTRY SOUNDER, 55

ENTRY/EXIT 1 ZONE OPTION, 30, 31, 32

ENTRY/EXIT 2 ZONE OPTION, 30, 31, 32

ERASING DEALER PROGRAM, 14

ERASING DEALER PROGRAM ADDRESS 4091, 52

ERASING ENTIRE PROGRAM, 14

ERASING ENTIRE PROGRAM ADDRESS 4093, 52

EVENT ID CODES, 50

EXIT DEALER PROGRAM MODE, 14

EXIT DELAY ADDRESS 0000, 19

EXIT/ENTRY FOLLOWER ZONE OPTION, 30, 31, 32

EXIT/ENTRY ZONES IN AREA 1, 6

EXIT/ENTRY2 ZONES IN AREA 1, 7

EXPANSION ZONE MODULE, 56

EXTERNAL RELAY BOARD MODULES, 51

EXTERNAL RELAY CONTROL / RELAYS 1-24 (ADDRESS 3778-3801

& 2800-2895), 47

EZM ADDRESS, 56

EZM GROUP OPTIONS (ADDRESS 2555-2576), 43

EZM PGM ARMED TERMINAL CONTROL, 43

50MS LOOP RESPONSE ZONES, 7

50MS LOOP RESPONSE ZONE OPTION, 30

FIRE ALARM VERIFICATION ZONE OPTION, 30, 31, 32

FIRE OUTPUT (LUG E9), 28, 29

FIRE OUTPUT (LUG E9) ZONE OPTION, 30, 31, 32

FIRE OUTPUT TIMEOUT ADDRESS 2405, 20

FIRE ZONE OPTION, 30, 31, 32

FIRE ZONES IN AREA 1, 6

FIRMWARE VERSION, 2

1400HZ HANDSHAKE/KISSOFF ADDRESS 0526, 21

1400HZ HANDSHAKE/KISSOFF ADDRESS 0551, 21

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 59

WI818G 10/05

ALPHABETICAL INDEX (CONT'D)

1400HZ HANDSHAKE/KISSOFF ADDRESS 0576, 21

FUNCTION MODE, 4

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY PROGRAM MENU, 6

GENERAL PROGRAMMING STEPS, 18

GLOBAL SYSTEM EVENT/TROUBLE, 28

GLOBAL SYSTEM TROUBLE REPORTING OPTIONS (ADDRESS

1082-1116), 28

HANDSHAKE FOR LOCAL TELEMETRY ADDRESS 1027, 25

HEXADECIMAL FORMAT, 17

INCLUDE SEL./GRP. BYPASS IN COND. CLOSING STATUS AD-

DRESS 2417, 34

INTERIOR #1 BYPASS ZONE OPTION, 30, 31, 32

INTERIOR #2 BYPASS ZONE OPTION, 30, 31, 32

INTERIOR (STAY) BYPASS ZONE OPTION, 30, 31, 32

INTERIOR 1 NORMALLY BYPASSED ADDRESS 2419, 34

INTERIOR ZONES IN AREA 1, 6

KEYFOB TRANSMITTERS AS ARM/DISARM & CONTROL DEVICES,

13

KEYFOB TRANSMITTERS AS ZONE INPUT DEVICES, 14

KEYFOB ZONE ASSIGNMENT, 13

KEYPAD ACCESS EVENT, 44

KEYPAD ADDRESS, 55

KEYPAD AREA ASSIGNMENT, 37

KEYPAD CONFIGURATION MODE, 55

KEYPAD EASY PROGRAM MENU, 6

KEYPAD HOME AREA / ACM DOOR #1 AREA (HEX) (ADDRESS

2425-2431), 40

KEYPAD INSTALLATION, 55

KEYPAD OPTIONS, 37

KEYPAD OPTIONS (ADDRESS 2425-2446), 37

KEYPAD REPORTING CODES ADDRESS 0900-0904, 25

KEYPAD SOUNDER ON ALARM ZONE OPTION, 30, 31, 32

KEYPAD SOUNDER ON ALARM ZONES, 7

KEYPAD SYSTEM CODES (ADDRESS 0490-0495 & 0500-0502), 20

KEYPAD TACTILE BEEP, 55

KEYPAD TYPE & AREA ASSIGNMENT, 37

KEYSWITCH ARMING ZONE OPTION, 30, 31, 32

LEADING DIGITS FOR PAGER FORMAT ADDRESS 0520, 21

LEADING DIGITS FOR PAGER FORMAT ADDRESS 0521, 21

LOCAL DOWNLOAD, 4

LOCAL DOWNLOADING, 4

LOCAL JACK, 4

LOCAL OR CENTRAL STATION REPORTING SYSTEM, 6

LOOP RESPONSE ZONES, 7

LUG E4 ARMED AWAY ONLY ADDRESS 2417, 34

MASTER SECURITY CODE, 5

MAXIMUM TWO-SWIPE ARM TIME ADDRESS 2782, 38

MODEM CODES, 26

NEVER ARM ZONE OPTION, 30, 31, 32

NEW CUSTOM DEFAULT PROGRAM, 5

NO EOL RESISTOR ZONE OPTION, 30, 31, 32

NUMBER OF KEYPADS IN AREA 1, 8

NUMBER OF KEYPADS IN AREA 2, 8

NUMBER OF RELAY BOARD MODULES (ADDRESS 3777), 51

NUMBER OF RF RECEIVERS ADDRESS 3776, 46

NUMBERING KEYPADS, 55

OPENING REPORT ONLY AFTER ALARM REPORT ADDRESS 2417,

34

OPENING/CLOSING REPORTING CODES ADDRESS 0864-0883, 24

OUTPUT SILENCED, 45

OUTPUT TIMEOUTS, 20

OUTPUT TURNS OFF UPON DISARM, 45

PAGER FORMAT: MAXIMUM PAGES PER SESSION ADDRESS

3904, 36

PAGER RECALLS ADDRESS 3903, 36

PANEL ACCESS CODE ADDRESS 0490-0492, 20

PCI2000/3000 COMPUTER INTERFACE, 4

PCI-MINI COMPUTER INTERFACE, 4

POWER-UP DELAY ZONE OPTION, 30, 31, 32

PRE-ALARM WARNING ZONE OPTION, 30, 31, 32

PRIORITY AREA ARMING, 44

PRIORITY WITH BYPASS ZONE OPTION, 30, 31, 32

PRIORITY ZONE OPTION, 30, 31, 32

PROGRAM CONTROL MESSAGE, 56

PROGRAMMING CONVENTIONS USED IN THIS MANUAL, 18

PROGRAMMING STEPS, 18

PROGRAMMING TRANSMITTER WIRELESS POINTS, 13

PROXIMITY CARDS, 12

PULSE ALARM OUTPUT TIMEOUT ADDRESS 2404, 20

PULSE BURG OUTPUT CADENCE ADDRESS 2422, 35

PULSE EVENT CODE, 26

PULSED ALARM OUTPUT ZONE OPTION, 30, 31, 32

PULSED BURG. OUTPUT, 28, 29

QUICK METHOD, 13

RECEIVER FORMATS, 21

RELAY BOARD MODULES, 51

RELAY EVENT ACTIVATION CONDITIONS, 51

RELAY EVENT ALARM TYPE OPTIONS, 51

RELAY EVENT CONDITION OPTIONS, 51

REMOTE ACCESS LOGGING (ADDRESS 3184), 44

REMOTE DOWNLOADING, 4

REPORT ALARM TELCO 1, 29

REPORT ALARM TELCO 3, 29

REPORT CANCEL WINDOW ADDRESS 4082, 20

REPORT EVENT TELCO 1, 28

REPORT EVENT TELCO 3, 28

REPORT RESTORE TELCO 1, 28

REPORT RESTORE TELCO 3, 28

REPORT TO TCP/IP RECEIVER OR AES (TELCO 1) ADDRESS

0526, 21

REPORT TO TCP/IP RECEIVER OR AES (TELCO 2) ADDRESS

0551, 21

REPORT TO TCP/IP RECEIVER OR AES (TELCO 3) ADDRESS

0576, 21

RESET DAY ZONE WITH ARM/DISARM ONLY ADDRESS 2419, 34

RESET OUTPUT TIMEOUT ADDRESS 2400, 20

RESET RELAY, 28, 29

RESET RELAY ZONE OPTION, 30, 31, 32

RF RECEIVERS & SUPERVISORY TIMER OPTIONS (ADDRESS

3776 & 3760-3775), 46

RF SUPERVISORY TIMERS, 46

RF TRANSMITTER POINTS, 13

RM3008, 51

ROTARY DIALING BACKUP, 25

RPT ALARM RESTORE TEL 1 ZONE OPTION, 30, 31, 32

RPT ALARM RESTORE TEL 3 ZONE OPTION, 30, 31, 32

RPT ALARM TEL 1 ZONE OPTION, 30, 31, 32

RPT ALARM TEL 3 ZONE OPTION, 30, 31, 32

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 60 WI818G 10/05

ALPHABETICAL INDEX (CONT'D)

RPT TROUBLE RESTORE TEL 1 ZONE OPTION, 30, 31, 32

RPT TROUBLE RESTORE TEL 3 ZONE OPTION, 30, 31, 32

RPT TROUBLE TEL 1 ZONE OPTION, 30, 31, 32

RPT TROUBLE TEL 3 ZONE OPTION, 30, 31, 32

SCHEMATIC, 68

SELECT BELL OUTPUT ON KEYFOB ARMING ADDRESS 2422, 35

SELECTIVE BYPASS ZONE OPTION, 30, 31, 32

SENSOR WATCH DELAY ADDRESS 4088, 19

SENSOR WATCH ZONE OPTION, 30, 31, 32

SENSOR WATCH ZONES, 7

SILENCE OUTPUT, 45

SINGLE DIGIT ONLY ADDRESS 0526, 21

SINGLE DIGIT ONLY ADDRESS 0551, 21

SINGLE DIGIT ONLY ADDRESS 0576, 21

SKIP AUTOMATIC DIAL TONE DETECT ADDRESS 4084, 36

START EXIT DELAY AFTER RINGBACK ADDRESS 2418, 34

STATUS REPORT (AUTO-BYP. ZONES ON CLOS.) ADDRESS 2417,

34

SUM CHECK ADDRESS 0526, 21

SUM CHECK ADDRESS 0551, 21

SUM CHECK ADDRESS 0576, 21

SUPERVISED ALARM OUTPUT ADDRESS 2422, 35

SUPPRESS “BYPASS” ICON WHEN ARMED ADDRESS 2418, 34

SWINGER SHUTDOWN ZONE OPTION, 30, 31, 32

SYSTEM DELAYS & TIMEOUTS (ADDRESS 0000-0002, 2402, 2406,

2414 & 3902), 19

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2400, 2401, 2403-2405,

4082 & 4083), 20

SYSTEM DELAYS & TIMEOUTS (ADDRESS 2407, 2408 & 4088), 19

SYSTEM OPTIONS (ADDRESS 2415-2419), 34

SYSTEM OPTIONS (ADDRESS 2420-2422, 3874, 3905, 3880-3881),

35

SYSTEM OPTIONS (ADDRESS 3882-3901, 3903-3905 & 4084), 36

SYSTEM OPTIONS ADDRESS 2417, 34

SYSTEM OPTIONS ADDRESS 2418, 34

SYSTEM OPTIONS ADDRESS 2419, 34

SYSTEM OPTIONS ADDRESS 2420, 35

SYSTEM OPTIONS ADDRESS 2421, 35

SYSTEM OPTIONS ADDRESS 2422, 35

SYSTEM OPTIONS ADDRESS 3874, 35

SYSTEM OPTIONS ADDRESS 3905, 35

SYSTEM PROGRAMMING OPTIONS, 4

SYSTEM RESET OPTIONS (ADDRESS 4091-4093), 52

SYSTEM RESPONSE ACTIVATED BY AREA EVENT/TROUBLE, 29

SYSTEM RESPONSE ACTIVATED BY GLOBAL EVENT/TROUBLE,

28

TABLE OF CONTENTS, 3

TACTILE BEEP, 55

TCP/IP PANEL/SITE INITIATED FUNCTIONS ADDRESS 2423, 41

TELCO CONNECTION, 4

TELCO FAIL ONLY WHEN ARMED ADDRESS 2420, 35

TELEPHONE DIALING PREFIX (DIGITS 1-20) ADDRESS 3882-3901,

36

TELEPHONE LINE TEST DELAY ADDRESS 2414, 19

TELEPHONE NUMBERS CS RECEIVER, 22

3/1 WITH EXTENDED RESTORES ADDRESS 0526, 21

3/1 WITH EXTENDED RESTORES ADDRESS 0551, 21

3/1 WITH EXTENDED RESTORES ADDRESS 0576, 21

TIME, 14, 54

TOTAL NUMBER OF ZONES IN AREA 1, 6

TOTAL NUMBER OF ZONES IN AREA 2, 6

TOUCH-TONE DIALING ONLY ADDRESS 1027, 25

TOUCH-TONE DIALING W/ROTARY BACKUP ADDRESS 1027, 25

TRANSMIT “402” OPENING/CLOSING CODE ADDRESS 1027, 25

TRANSMITTER WIRELESS POINTS, 13

TROUBLE ON NIGHT OPEN ZONE OPTION, 30, 31, 32

TROUBLE ON OPEN ZONE OPTION, 30, 31, 32

TROUBLE ON SHORT ZONE OPTION, 30, 31, 32

TROUBLE/ALARM REPORTING CODES (ADDRESS 3880-3881), 35

20MS LOOP RESPONSE ZONE OPTION, 30

2300HZ HANDSHAKE/KISSOFF ADDRESS 0551, 21

2300HZ HANDSHAKE/KISSOFF ADDRESS 0576, 21

24-HOUR ZONES IN AREA 1, 6

24-HOUR ZONE ZONE OPTION, 30, 31, 32

2ND CALL ANSWERING MACHINE OVERRIDE ADDRESS 2421, 35

2-WIRE FIRE ZONES IN AREA 1, 6

2-WIRE SMOKE DETECTORS ZONE OPTION, 30

UNLOCK TIME ADDRESS 2783, 38

USER AREA OPTIONS (ADDRESS 2455-2502), 42

USER CLOSING TELCO, 27

USER CODES, 10

USER CODES, 53

USER OPENING TELCO, 27

USER OPTIONS, 10

USER PROGRAM MODE, 52

VERI-PHONE ZONES PRIORITY OVER ALARMS ADDRESS 2421, 35

VERI-PHONE ZONES TRIP AUX. OUTPUT ADDRESS 2421, 35

VERI-PHONE ZONES TRIP FIRE OUTPUT ADDRESS 2421, 35

WIRELESS SMOKE LOW BATTERY RESOUND ADDRESS 2422, 35

WIRELESS SUPERVISORY ADDRESS 3880, 35

WIRELESS TAMPER ADDRESS 3881, 35

WIRELESS TROUBLE TO TELCO 1 ADDRESS 3874, 35

WIRELESS TROUBLE TO TELCO 3 ADDRESS 3874, 35

WIRING DIAGRAM, 68

WIZARD KEYPAD TYPE, 37

ZONE ANDING GROUP 1 ZONE OPTION, 30, 31, 32

ZONE ANDING GROUP 2 ZONE OPTION, 30, 31, 32

ZONE AREA 1 ZONE OPTION, 30, 31, 32

ZONE AREA 2 ZONE OPTION, 30, 31, 32

ZONE DESCRIPTIONS, 54

ZONE INPUT DEVICES, 14

ZONE OPTIONS / ZONES 1-16 (ADDRESS 1200-1386), 30

ZONE OPTIONS / ZONES 1-48 (ADDRESS 1200-1786), 33

ZONE OPTIONS / ZONES 17-32 (ADDRESS 1402-1586), 31

ZONE OPTIONS / ZONES 33-48 (ADDRESS 1602-1786), 32

ZONE RESPONSE, 56

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 61

WI818G 10/05

ADDRESS NUMBER INDEX

ADDRESS 0000 ...................... EXIT DELAY ..........................................................................................................19

ADDRESS 0000-0002 ............ SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 0001 ...................... ENTRY DELAY 1 ...................................................................................................19

ADDRESS 0002 ...................... ENTRY DELAY 2 ...................................................................................................19

ADDRESS 0490-0492 ............ PANEL ACCESS CODE .........................................................................................20

ADDRESS 0490-0495 ............ KEYPAD SYSTEM CODES ...................................................................................20

ADDRESS 0495 ...................... AMBUSH CODE .....................................................................................................20

ADDRESS 0500-0502 ............ DEALER SECURITY CODE ...................................................................................20

ADDRESS 0500-0502 ............ KEYPAD SYSTEM CODES ...................................................................................20

ADDRESS 0520 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0520 ...................... LEADING DIGITS FOR PAGER FORMAT .............................................................21

ADDRESS 0521 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0521 ...................... LEADING DIGITS FOR PAGER FORMAT .............................................................21

ADDRESS 0525 ...................... CS RECEIVER 1 FORMAT ....................................................................................21

ADDRESS 0525 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0526 ...................... CS RECEIVER 1 OPTIONS ...................................................................................21

ADDRESS 0526 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0526 ...................... ENABLE ZONE NUMBER ON PULSE ALARM ......................................................21

ADDRESS 0526 ...................... 1400HZ HANDSHAKE/KISSOFF ...........................................................................21

ADDRESS 0526 ...................... REPORT TO TCP/IP RECEIVER OR AES (TELCO 1) ..........................................21

ADDRESS 0526 ...................... SINGLE DIGIT ONLY .............................................................................................21

ADDRESS 0526 ...................... SUM CHECK ..........................................................................................................21

ADDRESS 0526 ...................... 3/1 WITH EXTENDED RESTORES .......................................................................21

ADDRESS 0527-0546 ............ CS RECEIVER TELEPHONE NUMBERS ..............................................................22

ADDRESS 0550 ...................... CS RECEIVER 2 FORMAT ....................................................................................21

ADDRESS 0550 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0551 ...................... CS RECEIVER 2 OPTIONS ...................................................................................21

ADDRESS 0551 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0551 ...................... ENABLE ZONE NUMBER ON PULSE ALARM ......................................................21

ADDRESS 0551 ...................... 1400HZ HANDSHAKE/KISSOFF ...........................................................................21

ADDRESS 0551 ...................... REPORT TO TCP/IP RECEIVER OR AES (TELCO 2) ..........................................21

ADDRESS 0551 ...................... SINGLE DIGIT ONLY .............................................................................................21

ADDRESS 0551 ...................... SUM CHECK ..........................................................................................................21

ADDRESS 0551 ...................... 3/1 WITH EXTENDED RESTORES .......................................................................21

ADDRESS 0551 ...................... 2300HZ HANDSHAKE/KISSOFF ...........................................................................21

ADDRESS 0552-0571 ............ CS RECEIVER TELEPHONE NUMBERS ..............................................................22

ADDRESS 0575 ...................... CS RECEIVER 3 FORMAT ....................................................................................21

ADDRESS 0575 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0576 ...................... CS RECEIVER 3 OPTIONS ...................................................................................21

ADDRESS 0576 ...................... CS RECEIVER FORMAT OPTIONS ......................................................................21

ADDRESS 0576 ...................... ENABLE ZONE NUMBER ON PULSE ALARM ......................................................21

ADDRESS 0576 ...................... 1400HZ HANDSHAKE/KISSOFF ...........................................................................21

ADDRESS 0576 ...................... REPORT TO TCP/IP RECEIVER OR AES (TELCO 3) ..........................................21

ADDRESS 0576 ...................... SINGLE DIGIT ONLY .............................................................................................21

ADDRESS 0576 ...................... SUM CHECK ..........................................................................................................21

ADDRESS 0576 ...................... 3/1 WITH EXTENDED RESTORES .......................................................................21

ADDRESS 0576 ...................... 2300HZ HANDSHAKE/KISSOFF ...........................................................................21

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 62 WI818G 10/05

ADDRESS NUMBER INDEX (CONT'D)

ADDRESS 0577-0596 ............ CS RECEIVER TELEPHONE NUMBERS ..............................................................22

ADDRESS 0600-0619 ............ DOWNLOAD/CALLBACK OPTIONS ......................................................................22

ADDRESS 0625-0647 ............ DOWNLOAD/CALLBACK OPTIONS ......................................................................22

ADDRESS 0645-0647 ............ DOWNLOAD SECURITY CODE ............................................................................22

ADDRESS 0650-0787 ............ CS SUBSCRIBER ID NUMBERS ...........................................................................23

ADDRESS 0790-0857 ............ CS SUBSCRIBER ID NUMBERS ...........................................................................24

ADDRESS 0859-0862 ............ ALARM/TROUBLE REPORTING CODES .............................................................24

ADDRESS 0859-0883 ............ CS REPORTING CODES ......................................................................................24

ADDRESS 0864-0883 ............ OPENING/CLOSING REPORTING CODES ..........................................................24

ADDRESS 0870-0904 ............ CS REPORTING CODES ......................................................................................25

ADDRESS 0900-0904 ............ KEYPAD REPORTING CODES .............................................................................25

ADDRESS 0910-0957 ............ CS ZONE REPORTING CODES ............................................................................26

ADDRESS 1022 ...................... CALLBACK TELEPHONE NO. SELECT ................................................................22

ADDRESS 1022 ...................... DOWNLOAD/CALLBACK OPTIONS ......................................................................22

ADDRESS 1023 ...................... AUTO DOWNLOAD ID NO. ...................................................................................22

ADDRESS 1023 ...................... DOWNLOAD/CALLBACK OPTIONS ......................................................................22

ADDRESS 1024-1027 ............ CS AREA & SYSTEM REPORTING OPTIONS .....................................................25

ADDRESS 1027 ...................... BACKUP REPORT ON TELCO 2 ...........................................................................25

ADDRESS 1027 ...................... CANCEL NEXT TEST TIMER ON ANY REPORT ..................................................25

ADDRESS 1027 ...................... CS SYSTEM REPORT OPTIONS ..........................................................................25

ADDRESS 1027 ...................... DISABLE WAIT FOR HANDSHAKE ........... ............................................................25

ADDRESS 1027 ...................... DISABLE WAIT FOR SILENCE ..............................................................................25

ADDRESS 1027 ...................... HANDSHAKE FOR LOCAL TELEMETRY ..............................................................25

ADDRESS 1027 ...................... TOUCH-TONE DIALING ONLY ..............................................................................25

ADDRESS 1027 ...................... TOUCH-TONE DIALING W/ROTARY BACKUP .....................................................25

ADDRESS 1027 ...................... TRANSMIT “402” OPENING/CLOSING CODE ......................................................25

ADDRESS 1030-1074 ............ CS USER REPORTING CODES ............................................................................27

ADDRESS 1082-1116 ............ GLOBAL SYSTEM TROUBLE REPORTING OPTIONS ........................................28

ADDRESS 1120-1137 ............ AREA SYSTEM TROUBLE REPORTING OPTIONS .............................................29

ADDRESS 1200-1386 ............ ZONE OPTIONS / ZONES 1-16 .............................................................................30

ADDRESS 1200-1786 ............ ZONE OPTIONS / ZONES 1-48 .............................................................................33

ADDRESS 1402-1586 ............ ZONE OPTIONS / ZONES 17-32 ...........................................................................31

ADDRESS 1602-1786 ............ ZONE OPTIONS / ZONES 33-48 ...........................................................................32

ADDRESS 2400 ...................... RESET OUTPUT TIMEOUT ...................................................................................20

ADDRESS 2400 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................20

ADDRESS 2401 ...................... AUX. OUTPUT TIMEOUT ......................................................................................20

ADDRESS 2401 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................20

ADDRESS 2402 ...................... AUX. OUTPUT ACCESS CONTROL TIMEOUT ....................................................19

ADDRESS 2402 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 2403 ...................... BURG. ALARM OUTPUT TIMEOUT ......................................................................20

ADDRESS 2403-2405 ............ SYSTEM DELAYS & TIMEOUTS ...........................................................................20

ADDRESS 2404 ...................... PULSE ALARM OUTPUT TIMEOUT ......................................................................20

ADDRESS 2405 ...................... FIRE OUTPUT TIMEOUT ......................................................................................20

ADDRESS 2406 ...................... ABORT DELAY ......................................................................................................19

ADDRESS 2406 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 2407 ...................... CHIME TIME ..........................................................................................................19

ADDRESS 2407 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 63

WI818G 10/05

ADDRESS NUMBER INDEX (CONT'D)

ADDRESS 2408 ...................... AC FAIL REPORT DELAY .....................................................................................19

ADDRESS 2408 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 2414 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 2414 ...................... TELEPHONE LINE TEST DELAY ..........................................................................19

ADDRESS 2415 ...................... DISABLE FIRE RESET ..........................................................................................34

ADDRESS 2415-2419 ............ SYSTEM OPTIONS ...............................................................................................34

ADDRESS 2416 ...................... ENABLE DAY ZONE WATCH ................................................................................34

ADDRESS 2417 ...................... CLOSING REPORT ONLY ON COND. CLOSING (AUTO-BYP.) ...........................34

ADDRESS 2417 ...................... DISABLE AUTO-UNBYPASS ON DISARMING .....................................................34

ADDRESS 2417 ...................... ENABLE ALL-ZONE-IN-TROUBLE BYPASS .........................................................34

ADDRESS 2417 ...................... INCLUDE SEL./GRP. BYPASS IN COND. CLOSING STATUS .............................34

ADDRESS 2417 ...................... LUG E4 ARMED AWAY ONLY ...............................................................................34

ADDRESS 2417 ...................... OPENING REPORT ONLY AFTER ALARM REPORT ...........................................34

ADDRESS 2417 ...................... STATUS REPORT (AUTO-BYP. ZONES ON CLOS.) ............................................34

ADDRESS 2417 ...................... SYSTEM OPTIONS ...............................................................................................34

ADDRESS 2418 ...................... ACCESS CONTROL (PANEL) ON AUX. OUTPUT ................................................34

ADDRESS 2418 ...................... AUTO BELL TEST ON ARMING ............................................................................34

ADDRESS 2418 ...................... AUTO RESET AFTER BURG. OUTPUT TIMEOUT ...............................................34

ADDRESS 2418 ...................... ENABLE BURG. OUTPUT WARNING ON ENTRY ................................................34

ADDRESS 2418 ...................... ENABLE MANAGER’S MODE OUTSIDE OVERVIEW ..........................................34

ADDRESS 2418 ...................... START EXIT DELAY AFTER RINGBACK ..............................................................34

ADDRESS 2418 ...................... SUPPRESS “BYPASS” ICON WHEN ARMED .................. .....................................34

ADDRESS 2418 ...................... SYSTEM OPTIONS ...............................................................................................34

ADDRESS 2419 ...................... DISABLE ANSWERING-MACHINE DOWNLOAD ..................................................34

ADDRESS 2419 ...................... DISABLE AUTO-RESET ON DAY ZONE ...............................................................34

ADDRESS 2419 ...................... DISABLE CALLBACK DOWNLOAD .......................................................................34

ADDRESS 2419 ...................... DISABLE KEYPAD FUNCTION-MODE DOWNLOAD ............................................34

ADDRESS 2419 ...................... ENABLE EXIT-DELAY RESTART ..........................................................................34

ADDRESS 2419 ...................... ENABLE LOCAL ALARM ON FIRST ZONE “AND” TRIP .......................................34

ADDRESS 2419 ...................... INTERIOR 1 NORMALLY BYPASSED ..................................................................34

ADDRESS 2419 ...................... RESET DAY ZONE WITH ARM/DISARM ONLY ....................................................34

ADDRESS 2419 ...................... SYSTEM OPTIONS ...............................................................................................34

ADDRESS 2420 ...................... CHIME ON LUG E4 ................................................................................................35

ADDRESS 2420 ...................... DISABLE AC FAIL DETECTION ............................................................................35

ADDRESS 2420 ...................... DISABLE CODE REQUIRED FOR EZ BYPASS ....................................................35

ADDRESS 2420 ...................... DISABLE CODE REQUIRED FOR FUNC. MODE LVL. 1 ......................................35

ADDRESS 2420 ...................... DISABLE KEYPAD INSTANT BUTTON .................................................................35

ADDRESS 2420 ...................... DISABLE SYSTEM TROUBLE AUDIBLE (AT KEYPAD) .......................................35

ADDRESS 2420 ...................... ENABLE TELEPHONE LINE-FAULT TEST ...........................................................35

ADDRESS 2420 ...................... SYSTEM OPTIONS ...............................................................................................35

ADDRESS 2420 ...................... TELCO FAIL ONLY WHEN ARMED ......................................................................35

ADDRESS 2420-2422 ............ SYSTEM OPTIONS ...............................................................................................35

ADDRESS 2421 ...................... AUTOMATIC INTERIOR BYPASS/EASY EXIT ......................................................35

ADDRESS 2421 ...................... DISABLE AUXOUT CLEAR ON DISARM ..............................................................35

ADDRESS 2421 ...................... DISABLE ZONE FAULT SCROLLING (AUTO STATUS) .......................................35

ADDRESS 2421 ...................... SYSTEM OPTIONS ...............................................................................................35

ADDRESS 2421 ...................... 2ND CALL ANSWERING MACHINE OVERRIDE ..................................................35

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 64 WI818G 10/05

ADDRESS NUMBER INDEX (CONT'D)

ADDRESS 2421 ...................... VERI-PHONE ZONES PRIORITY OVER ALARMS ...............................................35

ADDRESS 2421 ...................... VERI-PHONE ZONES TRIP AUX. OUTPUT ..........................................................35

ADDRESS 2421 ...................... VERI-PHONE ZONES TRIP FIRE OUTPUT ..........................................................35

ADDRESS 2422 ...................... DISABLE AREA ENTRY RELAYS .........................................................................35

ADDRESS 2422 ...................... DISABLE EXIT/ENTRY URGENCY TONE AT KEYPAD ........................................35

ADDRESS 2422 ...................... ENABLE BURG. OUTPUT ON TELCO FAIL ONLY WHEN ARMED .....................35

ADDRESS 2422 ...................... ENABLE SMOKE DETECTOR DIRTY TROUBLE .................................................35

ADDRESS 2422 ...................... PULSE BURG OUTPUT CADENCE ......................................................................35

ADDRESS 2422 ...................... SELECT BELL OUTPUT ON KEYFOB ARMING ...................................................35

ADDRESS 2422 ...................... SUPERVISED ALARM OUTPUT ...........................................................................35

ADDRESS 2422 ...................... SYSTEM OPTIONS ...............................................................................................35

ADDRESS 2422 ...................... WIRELESS SMOKE LOW BATTERY RESOUND ..................................................35

ADDRESS 2423 ...................... ACM SYSTEM OPTIONS .......................................................................................41

ADDRESS 2423 ...................... ENABLE ACM ACCESS .........................................................................................41

ADDRESS 2423 ...................... ENABLE KEYPAD BLANKING ...............................................................................41

ADDRESS 2423 ...................... ENABLE TCP/IP COMMUNICATIONS ...................................................................41

ADDRESS 2423 ...................... TCP/IP PANEL/SITE INITIATED FUNCTIONS ......................................................41

ADDRESS 2425-2431 ............ ACM DOOR #1 AREA (HEX) .................................................................................40

ADDRESS 2425-2431 ............ KEYPAD HOME AREA / ACM DOOR #1 AREA (HEX) ............... ........................ ...40

ADDRESS 2425-2446 ............ KEYPAD OPTIONS ................................................................................................37

ADDRESS 2455-2502 ............ USER AREA OPTIONS ..........................................................................................42

ADDRESS 2555-2576 ............ EZM GROUP OPTIONS .........................................................................................43

ADDRESS 2650-2651 ............ AREA ARMING OPTIONS .....................................................................................44

ADDRESS 2700-2739 ............ AREA OUTPUT CONTROL OPTIONS ...................................................................45

ADDRESS 2740-2769 ............ ACM ZONE OPTIONS ...........................................................................................38

ADDRESS 2780 ...................... ACM GLOBAL FLAGS ...........................................................................................38

ADDRESS 2780 ...................... ENABLE ACCESS LOGGING INTO BURG LOG ...................................................38

ADDRESS 2780 ...................... ENABLE CARD PRESENTATION BEEP AND GREEN LED FLASH .....................38

ADDRESS 2780 ...................... ENABLE FACILITY CODE .....................................................................................38

ADDRESS 2780 ...................... ENABLE NAPCO PROPRIETARY ACCESS FORMAT .........................................38

ADDRESS 2780 ...................... ENABLE PRINTING OF ACCESS EVENTS ..........................................................38

ADDRESS 2780 ...................... ENABLE TWO-SWIPE ARMING ............................................................................38

ADDRESS 2782 ...................... MAXIMUM TWO-SWIPE ARM TIME ......................................................................38

ADDRESS 2782-2783 ............ ACM TIMEOUTS ....................................................................................................38

ADDRESS 2783 ...................... UNLOCK TIME .......................................................................................................38

ADDRESS 2784-2787 ............ ACM DOOR AREA OPTIONS ................................................................................39

ADDRESS 2800-2895 ............ EXTERNAL RELAY CONTROL / RELAYS 1-24 ....................................................47

ADDRESS 3184 ...................... ENABLE KEYPAD--REMOTE ACCESS LOGGING ...............................................44

ADDRESS 3184 ...................... REMOTE ACCESS LOGGING ...............................................................................44

ADDRESS 3760-3775 ............ RF RECEIVERS & SUPERVISORY TIMER OPTIONS ..........................................46

ADDRESS 3776 ...................... NUMBER OF RF RECEIVERS ...............................................................................46

ADDRESS 3776 ...................... RF RECEIVERS & SUPERVISORY TIMER OPTIONS ..........................................46

ADDRESS 3777 ...................... NUMBER OF RELAY BOARD MODULES .............................................................51

ADDRESS 3778-3801 ............ EXTERNAL RELAY CONTROL / RELAYS 1-24 ....................................................47

ADDRESS 3874 ...................... ENABLE CANCEL REPORT TO TELCO 3 ............................................................35

ADDRESS 3874 ...................... ENABLE GEM-PRINT ............................................................................................35

ADDRESS 3874 ...................... ENABLE KEYPAD TIME/DATE DISPLAY ..............................................................35

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 65

WI818G 10/05

ADDRESS NUMBER INDEX (CONT'D)

ADDRESS 3874 ...................... ENABLE SET TIME/DATE MESSAGE ...................................................................35

ADDRESS 3874 ...................... SYSTEM OPTIONS ...............................................................................................35

ADDRESS 3874 ...................... WIRELESS TROUBLE TO TELCO 1 .....................................................................35

ADDRESS 3874 ...................... WIRELESS TROUBLE TO TELCO 3 .....................................................................35

ADDRESS 3880 ...................... WIRELESS SUPERVISORY ..................................................................................35

ADDRESS 3880-3881 ............ ALARM/TROUBLE REPORTING CODES .............................................................35

ADDRESS 3880-3881 ............ SYSTEM OPTIONS ...............................................................................................35

ADDRESS 3880-3881 ............ TROUBLE/ALARM REPORTING CODES .............................................................35

ADDRESS 3881 ...................... WIRELESS TAMPER .............................................................................................35

ADDRESS 3882-3901 ............ SYSTEM OPTIONS ...............................................................................................36

ADDRESS 3882-3901 ............ TELEPHONE DIALING PREFIX (DIGITS 1-20) .....................................................36

ADDRESS 3902 ...................... CS TELCO 3 REPORT DELAY ..............................................................................19

ADDRESS 3902 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 3903 ...................... PAGER RECALLS .................................................................................................36

ADDRESS 3903-3905 ............ SYSTEM OPTIONS ...............................................................................................36

ADDRESS 3904 ...................... PAGER FORMAT: MAXIMUM PAGES PER SESSION .........................................36

ADDRESS 3905 ...................... DIGITAL DIALER RPT ENTER/EXIT TEST MODE ................................................35

ADDRESS 3905 ...................... DISABLE CALL WAITING ON FIRST ATTEMPT ...................................................35

ADDRESS 3905 ...................... ENABLE AMBUSH IN USER ASSIGNMENT CODE TYPE ....................................35

ADDRESS 3905 ...................... ENABLE BELL ON EXIT ERROR ..........................................................................35

ADDRESS 3905 ...................... ENABLE CP-01 LIMITS ..........................................................................................35

ADDRESS 3905 ...................... ENABLE EXIT DELAY RESTART (SIA-FAR) .........................................................35

ADDRESS 3905 ...................... ENABLE REPORT EXIT ERR/RECENT CLOSE ...................................................35

ADDRESS 3905 ...................... SYSTEM OPTIONS ...............................................................................................35

ADDRESS 4072-4075 ............ ACM SCHEDULED FREE ACCESS ......................................................................39

ADDRESS 4080 ...................... EMERGENCY FREE ACCESS ..............................................................................41

ADDRESS 4082 ...................... REPORT CANCEL WINDOW ................................................................................20

ADDRESS 4082 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................20

ADDRESS 4083 ...................... AUTO DISARM REARM DELAY ............................................................................20

ADDRESS 4083 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................20

ADDRESS 4084 ...................... SKIP AUTOMATIC DIAL TONE DETECT ..............................................................36

ADDRESS 4084 ...................... SYSTEM OPTIONS ...............................................................................................36

ADDRESS 4088 ...................... SENSOR WATCH DELAY .....................................................................................19

ADDRESS 4088 ...................... SYSTEM DELAYS & TIMEOUTS ...........................................................................19

ADDRESS 4089 ...................... ANSWER ON RING NUMBER ...............................................................................22

ADDRESS 4089 ...................... DOWNLOAD/CALLBACK OPTIONS ......................................................................22

ADDRESS 4091 ...................... CLEAR DEALER PROGRAM .................................................................................52

ADDRESS 4091 ...................... ERASING DEALER PROGRAM .............................................................................52

ADDRESS 4091-4093 ............ SYSTEM RESET OPTIONS ...................................................................................52

ADDRESS 4093 ...................... COLD START ........................................................................................................52

ADDRESS 4093 ...................... ERASING ENTIRE PROGRAM ..............................................................................52

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 66 WI818G 10/05

NOTES

L NAPCO Security Systems X GEM-P3200 Programming Instructions



Page 67

WI818G 10/05

NOTES

X GEM-P3200 Programming Instructions L NAPCO Security Systems

 Page 68 WI818G 10/05

GEM-P3200 WIRING DIAGRAM

Napco Security Technologies Gemini Gem P3200 Users Manual P3200_RP1_WI818G.17_PROG

GEM-P3200 to the manual 3cd70f2c-0ac6-44a6-9092-5671b1937160

Navigation menu

Versions of this User Manual:

Views

Navigation