Nedap N V STOREIDG ANTI Pilferage device and UHF RFID reader User Manual 14r03 9964142 QR T ID Gate Version C 01 CGDSTOREIDG

N. V. Nederlandsche Apparatenfabriek NEDAP ANTI Pilferage device and UHF RFID reader 14r03 9964142 QR T ID Gate Version C 01 CGDSTOREIDG

14r03_9964142-QR-T-ID Gate-Version C.01 CGDSTOREIDG

Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be repro-duced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP.doc. article no: 5278988chk: rev. : C.01drw: CB 2013/06/13sheet: 45.01 of 1drawing: T5278-988!D GatedimensionsGROENLO - HOLLAND 462 10 (oorpart) 1668 195,5 828,75 1024,25 300 150(2x) 60(2x) 13(6x) 70 100 57 sales oor stock roomorientation in the shop all antennas in the same direction.distance between antennas1x !D Gate 1x Coax cable 3m/10ftdescription:quick reference !D Gate ABPower inserterrecommended - 2.0m / 6.5ftabsolute max. - 2.2m / 7ftABABABABABAB462mm / 18.2”1668mm / 5.7ft828.75mm / 2.7ft 195.5mm / 7.7”1024.25mm / 3.4ft100mm / 3.9”57mm / 2.2”70mm / 2.8”
Reinforced ConcreteIronReinforced ConcreteNylon Insulation ring(included in installation set)Retainer ring (not included in installationset)IronAlways mount an antenna insulated to the floor or wallNut (not included in installationset)Nylon M10(included ininstallation set)4xM10241Metal M1030403Hilti-hit not includedCleaning Hilti-hit Place nut053001506013(6x)90mm / 3.5”ø 13mm / ø 0.5”02remove covers01 drilling holesNut (not included in installationset)Retainer ring (not included in installationset)Nylon Insulation ring (included in installationset)Always mount an antenna insulated to the oor or wall300mm / 11.8”150mm / 5.9” 13mm / 0.5”60mm / 2.4”
processing unitnetwork INnetwork OUTUSB service portUSB hostPower for ReaderRecommended to place in switch-roompower supply OutInPower supply 9561811. One needed for every installed system. (not included)1 Yellow Heartbeat2 Green Disk access3 Green Firmware running1 2 3+-buzzerNot compatible with IEEE 802.3a* standardCDEF10721FE8111293456GHGHCDEF10721FE8111293456GHGHLed Blue Orange Red Green Green-Firmware running Error RFID active Powernextprevious!D Reader1 Green Processing unit at output2 Blue Blink No device at output or Lan- modem (in case of OST integration)Blue Continuous Power inserter at output3 Red Power error
coax cable 3m / 10ft 2x coax cable 3m / 10ftno coax cable needed recommended label free zone 1m / 3ftrequired label free zone 1m / 3ft1m / 3ft1m / 3ft2m / 6ft 2m / 6ft0.5m / 1.5ft0.5m / 1.5ft
place covers230V110Vconnect voltage supplyNote :The start up of all the processes takes approximately 3 minutes.02use rmware conguration quick reference.nextcoax-cable 3m/10ft2 101Minimum bendingradius = >60mm/2.4”previous coax cablecoax cableRJ45 connector to ethernet outlet - customer network.processing unitnetwork IN2OUTINnote:use only cat5e ethernet cable or better,with all 8 wires connected.(straight cable)1processing unit network IN03processing unit network OUT RJ45 connector to ethernet outlet - customer network.2note:use only cat5e ethernet cable or better,with all 8 wires connected.(straight cable)1
Model: !D Gate Region 2FCC ID: CGDSTOREIDG IC: 1444A-STOREIDGThis device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may causeundesired operation. Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada.L’opération est soumis aux deux conditions suivantes:(1) cet appareil ne doit causer aucune interférence, et(2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causerune opération non pas voulu de cet appareil. Les changements ou modications n’ayant pas été expressément approuvés par la partie responsable de la conformité peuvent faire perdre à l’utilisateur l’autorisation de faire fonctionner le matériel.FCC and IC Radiation Exposure Statement:This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncon-trolled environment. This equipment should be installed and operated with a minimum distance of 3.65 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Cet équipement est conforme a RSS-102 limites énoncées pour un environne-ment non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 3.65 cm entre le radiateur et votre corps.This Class B digital apparatus complies with Canadian ICES-003Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003

Navigation menu