Nedap N V STOREIDG ANTI Pilferage device and UHF RFID reader User Manual 14r03 9964142 QR T ID Gate Version C 01 CGDSTOREIDG

Download:
Mirror Download [FCC.gov]
Document ID	1995137
Application ID	ka6nqWPWmUk56oc1xrjR1Q==
Document Description	14r03_9964142-QR-T-ID Gate-Version C.01 CGDSTOREIDG
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	268.35kB (3354328 bits)
Date Submitted	2013-06-19 00:00:00
Date Available	2013-06-19 00:00:00
Creation Date	2017-10-26 23:49:42
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-26 23:49:42
Document Title	14r03_9964142-QR-T-ID Gate-Version C.01 CGDSTOREIDG
Document Creator	Adobe InDesign CS6 (Windows)

!D Gate
1x !D Gate
1x Coax cable 3m/10ft
dimensions
distance between antennas
70mm / 2.8”
70
57mm / 2.2”
57
10 (floorpart)
828.75mm
828,75/ 2.7ft
1024.25mm
1024,25/ 3.4ft
1668mm
1668/ 5.7ft
195,5
195.5mm / 7.7”
60(2x)
462mm
462/ 18.2”
recommended - 2.0m / 6.5ft
absolute max. - 2.2m / 7ft
100mm
/ 3.9”
100
orientation in the shop
Power inserter
all antennas
in the same
direction.
sales loor
stock room
drw: CB 2013/06/13
GROENLO - HOLLAND
chk:
description:
doc. article no: 5278988
quick reference !D Gate
rev. : C.01
Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the
prior written permission of NEDAP.
sheet: 45.01 of 1
drawing: T5278-988
01
02
remove covers
drilling holes
150
300
300mm / 11.8”
13mm
/ 0.5”
13
(6x)
150mm / 5.9”
60
60mm / 2.4”
90mm / 3.5”
ø 13mm / ø 0.5”
03
04
4x
M10
Metal M10
Nylon M10
(included in
installation set)
Cleaning
Hilti-hit
Place nut
Hilti-hit not included
05
Nut (not included in installationset)
Retainer ring (not included in installationset)
Nylon Insulation ring (included in installationset)
Nut (not included in installationset)
Retainer ring (not included in installationset)
Nylon Insulation ring
(included in installation set)
Iron
Iron
Reinforced Concrete
Reinforced Concrete
Always mount an antenna insulated to the loor or wall
Always mount an antenna insulated to the loor or wall
power supply
processing unit
Out
In
Power for Reader
network IN
USB host
network OUT
USB service port
Power supply 9561811. One needed for
every installed system. (not included)
Not compatible with IEEE 802.3a* standard
Recommended to place in switch-room
1 Yellow Heartbeat
1 2 3
Blue
Disk access
3 Green
Firmware running
buzzer
Processing unit at output
1 Green
2 Blue
2 Green
No device at output or Lan- modem (in case of OST integration)
Blink
Continuous Power inserter at output
Power error
3 Red
!D Reader
previous
next
Led Blue
Orange
Red
Firmware running Error
Green
Green
RFID active
Power
no coax cable needed
coax cable 3m / 10ft
1m / 3ft
0.5m / 1.5ft
2x coax cable 3m / 10ft
1m / 3ft
2m / 6ft
1m / 3ft
required label free zone
recommended label free zone
2m / 6ft
1m / 3ft
0.5m / 1.5ft
01

coax cable
previous

next
coax cable
Minimum bending
radius = >60mm/2.4”
coax-cable 3m/10ft
02
note:
use only cat5e ethernet cable or better,
with all 8 wires connected.(straight cable)
processing unit
network IN
OUT
IN
RJ45 connector to ethernet
outlet - customer network.
03
processing unit
network IN
place covers
note:
use only cat5e ethernet cable or better,
with all 8 wires connected.(straight cable)
processing unit
network OUT
RJ45 connector to ethernet
outlet - customer network.
connect voltage supply
230V
110V
Note :
The start up of all the
processes takes
approximately 3 minutes.
use irmware coniguration quick reference.
Model: !D Gate Region 2
FCC ID: CGDSTOREIDG
IC: 1444A-STOREIDG
This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modiications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Cet appareil se conforme aux normes RSS 210 exemptés de license du Industry Canada.
L’opération est soumis aux deux conditions suivantes:
(1) cet appareil ne doit causer aucune interférence, et
(2) cet appareil doit accepter n’importe quelle interférence, y inclus interférence qui peut causer
une opération non pas voulu de cet appareil.
Les changements ou modiications n’ayant pas été expressément approuvés par la partie
responsable de la conformité peuvent faire perdre à l’utilisateur l’autorisation de faire fonctionner le
matériel.
FCC and IC Radiation Exposure Statement:
This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of
3.65 cm between the radiator and your body. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
Cet équipement est conforme a RSS-102 limites énoncées pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale
de 3.65 cm entre le radiateur et votre corps.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2013:06:19 09:48:50+02:00
Create Date                     : 2013:06:13 11:56:10+02:00
PXC Viewer Info                 : PDF-XChange Viewer;2.5.210.0;Feb 25 2013;15:35:42;D:20130619094850+02'00'
Page Count                      : 8
Tagged PDF                      : Yes
XMP Toolkit                     : XMP Core 4.1.1
Metadata Date                   : 2013:06:13 11:56:28+02:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:09bceb2f-6e09-4fd3-b5d3-2962fed4c60e
Original Document ID            : xmp.did:FD7F1174072068119457DD866944A140
Document ID                     : xmp.id:E1B4ED710FD4E211A53A877E885D4448
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:E0B4ED710FD4E211A53A877E885D4448
Derived From Document ID        : xmp.did:559852171797E011834BCD9303682CD1
Derived From Original Document ID: xmp.did:FD7F1174072068119457DD866944A140
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2013:06:13 11:56:10+02:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False

EXIF Metadata provided by EXIF.tools