Netgear orporated 13200233 R7000 AC1900 Smart WiFi Router / AC1750 Smart WiFi Router User Manual Part 1

Download:
Mirror Download [FCC.gov]
Document ID	2611483
Application ID	11zB9jPnXPczkzaNGRa0Mg==
Document Description	User Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	410.66kB (5133269 bits)
Date Submitted	2015-05-12 00:00:00
Date Available	2015-05-13 00:00:00
Creation Date	2017-10-04 23:59:12
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-04 23:59:12
Document Title	NETGEAR Nighthawk AC1750 Smart WiFi Router Model R6700 User Manual
Document Creator	FrameMaker 10.0.2
Document Author:	NETGEAR

Nighthawk
AC1750 Smart WiFi Router
Model R6700
User Manual
July 2014
202-11361-01
350 East Plumeria Drive
San Jose, CA 95134
USA
Nighthawk AC1750 Smart WiFi Router
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use it to register your product at
https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR
recommends registering your product through the NETGEAR website. For product updates and web support, visit
http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.
Compliance
For regulatory compliance information, visit http://www.netgear.com/about/regulatory.
See the regulatory compliance document before connecting the power supply.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc.
and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice.
© NETGEAR, Inc. All rights reserved.
Contents
Chapter 1
Hardware Setup
Unpack Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Attach the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Top and Front Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Position Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cable Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Chapter 2
Connect to the Network and Access the Router
Connect to the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wired Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WiFi Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of Logins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use an Internet Browser to Access the Router . . . . . . . . . . . . . . . . . . . . . . . . . . .
NETGEAR genie Automatic Internet Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Log In to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Change the Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access the Router with NETGEAR genie App . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3
16
16
16
17
17
17
17
19
19
20
Specify Your Internet Settings
Use the Internet Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manually Set Up the Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specify an Internet Connection Without a Login. . . . . . . . . . . . . . . . . . . . . . .
Specify an Internet Connection That Uses a Login . . . . . . . . . . . . . . . . . . . . .
Specify IPv6 Internet Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for Entering IPv6 Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use Auto Detect for an IPv6 Internet Connection. . . . . . . . . . . . . . . . . . . . . .
Use Auto Config for an IPv6 Internet Connection . . . . . . . . . . . . . . . . . . . . . .
Set Up an IPv6 6to4 Tunnel Internet Connection . . . . . . . . . . . . . . . . . . . . . .
Set Up an IPv6 Pass Through Internet Connection . . . . . . . . . . . . . . . . . . . . .
Set Up an IPv6 Fixed Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up an IPv6 DHCP Internet Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up an IPv6 PPPoE Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Transmission Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Change the MTU Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common MTU Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
23
23
25
27
28
28
29
31
32
33
35
36
38
39
39
Nighthawk AC1750 Smart WiFi Router
Chapter 4 Optimize Performance
Prioritize Internet Traffic with Quality of Service . . . . . . . . . . . . . . . . . . . . . . . .
Optimize Internet Gaming with Upstream QoS . . . . . . . . . . . . . . . . . . . . . . . . . .
Add Upstream QoS Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up QoS for Applications and Online Gaming . . . . . . . . . . . . . . . . . . . . . . .
Set Up QoS for a Router LAN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up QoS for a MAC Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edit an Upstream QoS Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete an Upstream QoS Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optimize Video Streaming with Downstream QoS . . . . . . . . . . . . . . . . . . . . . . .
Add Downstream QoS Rules by Keyword . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add a Downstream QoS Rule by Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Improve Network Connections with Universal Plug and Play. . . . . . . . . . . . . . .
Wi-Fi Multimedia Quality of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 5
Control Access to the Internet
Set Up Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Access to Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use Keywords to Block Internet Sites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete Keywords from the List to Be Blocked . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block Services from the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schedule When to Block Internet Sites and Services . . . . . . . . . . . . . . . . . . . . . .
Avoid Blocking on a Trusted Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up Security Event Email Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6
57
59
60
61
62
64
64
65
Share USB Drives Attached to the Router
USB Drive Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access a USB Device on the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back Up Windows Computers with ReadySHARE Vault. . . . . . . . . . . . . . . . . . . .
Back Up Mac Computers with Time Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Up a USB Hard Drive on a Mac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prepare to Back Up a Large Amount of Data . . . . . . . . . . . . . . . . . . . . . . . . . .
Use Time Machine to Back Up onto a USB Hard Drive . . . . . . . . . . . . . . . . . .
Control Access to the USB Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use FTP Within the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Network Folders on a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add a Network Folder on a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edit a Network Folder on a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Approve USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safely Remove a USB Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 7
42
42
43
44
46
47
48
49
50
51
52
53
54
68
68
70
71
71
71
72
73
74
75
76
77
78
79
Access the Router’s USB Drive Through the Internet
Access the USB Drive Through the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Set Up FTP Access Through the Internet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Access the USB Drive Through the Internet with FTP . . . . . . . . . . . . . . . . . . . 83
Nighthawk AC1750 Smart WiFi Router
Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Your Personal FTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Set Up a New Dynamic DNS Account. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Specify a DNS Account That You Already Use . . . . . . . . . . . . . . . . . . . . . . . . . 86
Change the Dynamic DNS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Set Up Your Personal FTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Chapter 8
Use the Router as a Media Server
Specify ReadyDLNA Media Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Play Music from a USB Drive with iTunes Server . . . . . . . . . . . . . . . . . . . . . . . . . 90
Play Media from a USB Drive on TiVo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Chapter 9
Share a USB Printer
Install the Printer Driver and Cable the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Download the ReadySHARE Printer Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Install the ReadySHARE Printer Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Use the Shared Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
View or Change the Status of a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Use the Scan Feature of a Multifunction USB Printer . . . . . . . . . . . . . . . . . . . . 100
Change NETGEAR USB Control Center Settings . . . . . . . . . . . . . . . . . . . . . . . . . 101
Chapter 10
Specify Network Settings
Disable LED Blinking or Turn Off LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
View WAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Set Up a Default DMZ Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Change the Router’s Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Change the LAN TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Specify the IP Addresses That the Router Assigns . . . . . . . . . . . . . . . . . . . . . . . 109
Disable the DHCP Server Feature in the Router . . . . . . . . . . . . . . . . . . . . . . . . . 110
Reserve LAN IP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Edit a Reserved LAN IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Delete a Reserved LAN IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Use the WPS Wizard for WiFi Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Specify Basic WiFi Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Change the WiFi Security Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Set Up a Guest Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
How the Router Manages Wireless Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Airtime Fairness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Implicit Beamforming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Control the Wireless Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Use the WiFi On/Off Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Enable or Disable the Wireless Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Set Up a Wireless Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Specify WPS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Use the Router as a Wireless Access Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Set Up the Router in Bridge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Nighthawk AC1750 Smart WiFi Router
Set Up a Wireless Distribution System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Set Up the Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Set Up a Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Chapter 11
Manage Your Network
Update the Router Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Change the admin Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Set Up Password Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Recover the admin Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
View Router Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Display Internet Port Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Check the Internet Connection Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
View Logs of Router Activity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Monitor Internet Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Create Custom Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Edit a Static Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Delete a Static Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
View Devices Currently on the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Manage the Router Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Back Up Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Restore Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Erase the Current Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Remote Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Chapter 12
Use VPN to Access Your Network
Set Up a VPN Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Specify VPN Service in the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Install OpenVPN Software on Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Use a VPN Tunnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Use VPN to Access the Router’s USB Drive and Media . . . . . . . . . . . . . . . . . . . 154
Use VPN to Access Your Internet Service at Home . . . . . . . . . . . . . . . . . . . . . . 155
Set Up VPN Client Internet Access in the Router . . . . . . . . . . . . . . . . . . . . . . 155
Block VPN Client Internet Access in the Router . . . . . . . . . . . . . . . . . . . . . . . 156
Use a VPN Tunnel to Access Your Internet Service at Home . . . . . . . . . . . . 156
Chapter 13
Specify Internet Port Settings
Set Up Port Forwarding to a Local Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Add a Custom Port Forwarding Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Edit a Port Forwarding Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Delete a Port Forwarding Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Application Example: Make a Local Web Server Public . . . . . . . . . . . . . . . . . 162
How the Router Implements the Port Forwarding Rule . . . . . . . . . . . . . . . . 162
Set Up Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Add a Port Triggering Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Enable Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Application Example: Port Triggering for Internet Relay Chat . . . . . . . . . . . 165
Nighthawk AC1750 Smart WiFi Router
Chapter 14
Troubleshooting
Quick Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Sequence to Restart Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Check Ethernet Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Troubleshoot with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Standard LED Behavior When the Router Is Powered On . . . . . . . . . . . . . . . 169
Power LED Is Off or Blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Power LED Stays Amber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
LEDs Never Turn Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Internet or Ethernet Port LEDs Are Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
WiFi LED Is Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Cannot Log In to the Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Cannot Access the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Troubleshoot PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Troubleshoot Internet Browsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Changes Not Saved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Wireless Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Troubleshoot Your Network Using the Ping Utility . . . . . . . . . . . . . . . . . . . . . . . 174
Test the LAN Path to Your Router. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Test the Path from Your Computer to a Remote Device . . . . . . . . . . . . . . . . 175
Appendix A
Supplemental Information
Factory Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
1.
Hardware Setup
The Nighthawk AC1750 Smart WiFi Router delivers combined WiFi connection speeds up to
AC1750 (450 Mbps1 at 2.4 GHz 802.11n and 1300 Mbps2 at 5 GHz 802.11ac). Nighthawk is
ideal for bandwidth-hungry activities such as online gaming and video streaming, powered by a
dual-core 1 GHz processor. High-powered amplifiers with antennas provide WiFi coverage
anywhere around your home, inside or out.
For gamers, Nighthawk supports upstream Quality of Service (QoS) optimized for online game
play with game consoles like Xbox. For uninterrupted HD streaming media, Nighthawk features
downstream QoS to identify and prioritize streaming traffic from websites like Netflix, YouTube,
and Hulu Plus.
Nighthawk provides fast central storage, backup, and streaming to every device in your home
with the USB 3.0 port (10 times faster than USB 2.0). Sharing content across your network is
easy, whether you’re accessing stored photos and music or printing wirelessly. Stream your
stored media files anywhere on the network to DLNA screens. Share your music to
AirPlay-compatible devices from the USB hard drive connected to the router. Use the free
NETGEAR ReadySHARE Vault app to back up your Windows computers to a USB hard drive
connected to Nighthawk.
This chapter contains the following sections:
•
Unpack Your Router
•
Attach the Antennas
•
Top and Front Panels
•
Rear Panel
•
Position Your Router
•
Cable Your Router
For more information about the topics covered in this manual, visit the support website at
http://support.netgear.com.
1. Maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data throughput and wireless coverage will vary. Network
conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual
data throughput rate and wireless coverage. NETGEAR makes no express or implied representations or warranties about this product’s compatibility
with any future standards. 802.11ac 1300 Mbps is approximately 3x faster than 802.11n 450 Mbps.
2. Up to 1300 Mbps wireless speeds achieved when you are connecting to other 802.11ac 1300 Mbps devices.
Nighthawk AC1750 Smart WiFi Router
Unpack Your Router
Your package contains the following items.
Nighthawk AC1750 Smart WiFi Router
Ethernet cable
Power adapter
Antennas (3)
Figure 1. Package contents
Attach the Antennas
The router comes with three antennas.

To attach the antennas:
1. Align the antennas with the antenna posts on the router.
2. Attach the antennas on the threaded antenna posts.
3. Position the antennas for the best WiFi performance.
NETGEAR recommends that the center antenna be vertical and that you aim the others
outward at 45-degree angles, as shown.
Hardware Setup
Nighthawk AC1750 Smart WiFi Router
Top and Front Panels
Status LEDs are located on top and a USB 3.0 port is located on the front.
USB 3.0 port
Figure 2. Router top and front view
Table 1. LED and button descriptions
LED
Description
Power
•
•
•
•
•
Solid amber. The router is starting.
Blinking amber. The firmware is upgrading or the Reset button was pressed.
Solid white. The router is ready.
Blinking white. The firmware is corrupted.
Off. Power is not supplied to the router.
Internet
•
•
•
Solid white. The Internet connection is ready.
Solid amber. The router detects an Ethernet cable connection to the modem.
Off. No Ethernet cable is connected between the router and the modem.
2.4 GHz
Wireless
•
•
•
Solid white. The 2.4 GHz WiFi radio is operating.
Blinking. The router is sending or receiving WiFi traffic.
Off. The 2.4 GHz WiFi radio is off.
5 GHz Wireless
•
•
•
Solid white. The 5 GHz WiFi radio is operating.
Blinking. The router is sending or receiving WiFi traffic.
Off. The 5 GHz WiFi radio is off.
•
•
Solid white. The guest WiFi is operating.
Off. The guest WiFi is off.
Guest WiFi
Hardware Setup
10
Nighthawk AC1750 Smart WiFi Router
Table 1. LED and button descriptions (continued)
LED
Description
USB 3.0
•
•
•
Ethernet ports
1–4
The LED color indicates the speed: white for Gigabit Ethernet connections and amber for 100
Mbps or 10 Mbps Ethernet connections.
• Solid white. A powered-on device is connected to the Ethernet port.
• Blinking white. The port is sending or receiving traffic.
• Off. No device is connected to this Ethernet port.
Solid white. A USB device is connected and is ready.
Blinking. A USB device is plugged in and is trying to connect.
Off. No USB device is connected or someone clicked the Reset button, and it is now safe
to remove the attached USB device.
WiFi On/Off
Pressing this button for two seconds turns the 2.4 GHz and 5 GHz WiFi radios on and off.
button with LED If this LED lights solid white, the WiFi radios are on. If this LED is off, the WiFi radios are
turned off and you cannot use WiFi to connect to the router.
WPS button with This button lets you use WPS to join the WiFi network without typing the WiFi password. The
LED
WPS LED blinks white during this process and then lights solid white.
You can disable LED blinking or turn off all LEDs except the Power LED. For information
about how to do this, see Disable LED Blinking or Turn Off LEDs on page 104.
Hardware Setup
11
Nighthawk AC1750 Smart WiFi Router
Rear Panel
The connections and buttons shown in the following figure are located on the rear panel.
Reset
button
Ethernet
LAN ports 1–4
Internet
port
Power
On/Off
Power
connector
Figure 3. Router rear panel
Pressing the Reset button restores the factory settings. See Factory Settings on page 178.
Position Your Router
The router lets you access your network anywhere within the operating range of your
wireless network. However, the operating distance or range of your wireless connection can
vary significantly depending on the physical placement of your router. For example, the
thickness and number of walls the wireless signal passes through can limit the range.
Additionally, other wireless access points in and around your home might affect your router’s
signal. Wireless access points are routers, repeaters, WiFi range extenders, and any other
device that emits a wireless signal for network access.
Position your router according to the following guidelines:
•
Place your router near the center of the area where your computers and other devices
operate and within line of sight to your wireless devices.
•
Make sure that the router is within reach of an AC power outlet and near Ethernet cables
for wired computers.
•
Place the router in an elevated location, minimizing the number walls and ceilings
between the router and your other devices.
Hardware Setup
12
Nighthawk AC1750 Smart WiFi Router
•
•
Place the router away from electrical devices such as these:
Ceiling fans
Home security systems
Microwaves
Computers
Base of a cordless phone
2.4 GHz cordless phone
Place the router away from large metal surfaces, large glass surfaces, insulated walls,
and items such as these:
Solid metal doors
Aluminum studs
Fish tanks
Mirrors
Brick
Concrete
Cable Your Router
The following image shows how to cable your router:
Ethernet cable
DSL or cable
Router
Ethernet
cable
Modem
Power adapter
Figure 4. Router cabling
Hardware Setup
13
Nighthawk AC1750 Smart WiFi Router

To cable your router:
1. Unplug your modem’s power, leaving the modem connected to the wall jack for your
Internet service.
If your modem uses a battery, remove the battery.
2. Plug in and turn on your modem.
If your modem uses a battery, put the battery back in.
3. Connect your modem to the Internet port of your router with the yellow Ethernet cable that
came with your router.
4. Connect the power adapter to your router and plug the power adapter into an outlet.
5. Press the Power On/Off button on the rear panel of the router.
Hardware Setup
14
2.
Connect to the Network and
Access the Router
You can connect to the router’s WiFi network or use a wired Ethernet connection. This chapter
explains the ways you can connect and how to access the router and log in.
This chapter contains the following sections:
•
Connect to the Network
•
Types of Logins
•
Use an Internet Browser to Access the Router
•
Change the Language
•
Access the Router with NETGEAR genie App
15
Nighthawk AC1750 Smart WiFi Router
Connect to the Network
You can connect to the router’s network through a wired or WiFi connection. If you set up
your computer to use a static IP address, change the settings so that it uses Dynamic Host
Configuration Protocol (DHCP).
Wired Connection
You can connect your computer to the router using an Ethernet cable and join the router’s
local area network (LAN).

To connect your computer to the router with an Ethernet cable:
1. Make sure power is supplied the router (its Power LED is lit).
2. Connect an Ethernet cable to an Ethernet port on your computer.
3. Connect the other end of the Ethernet cable to one of the numbered Ethernet ports.
Your computer connects to the local area network (LAN). A message might display on
your computer screen to notify you that an Ethernet cable is connected.
WiFi Connection
You can connect to the router’s WiFi network with Wi-Fi Protected Setup (WPS) or you can
find and select the WiFi network.

To use WPS to connect to the WiFi network:
1. Make sure power is supplied the router (its Power LED is lit).
2. Check the WPS instructions for your computer or wireless device.
3. Press the WPS button on the router.
4. Within two minutes, on your computer or WiFi device, press its WPS button or follow its
instructions for WPS connections.
Your computer or wireless device connects to the WiFi network.

To find and select the WiFi network:
1. Make sure that the router has power (its Power LED is lit).
2. On your computer or wireless device, find and select the WiFi network.
The WiFi network name is on the router’s label.
3. Join the WiFi network and enter the WiFi password.
The password is on the router’s label.
Your wireless device connects to the WiFi network.
Connect to the Network and Access the Router
16
Nighthawk AC1750 Smart WiFi Router
Label
The label on the router shows the login information, MAC address, and serial number.
Figure 5. Product label
Types of Logins
Separate types of logins serve different purposes. It is important that you understand the
difference so that you know which login to use when.
Types of logins:
•
ISP login. The login that your ISP gave you logs you in to your Internet service. Your
service provider gave you this login information in a letter or some other way. If you
cannot find this login information, contact your service provider.
•
WiFi network key or password. Your router is preset with a unique wireless network
name (SSID) and password for wireless access. This information is on the product label.
•
Router login.This logs you in to the router interface from an Internet browser as admin.
Use an Internet Browser to Access the Router
When you connect to the network (either with WiFi or with an Ethernet cable), you can use an
Internet browser to access the router to view or change its settings. The first time you access
the router, NETGEAR genie automatically checks to see if your router can connect to your
Internet service.
NETGEAR genie Automatic Internet Setup
You can set up your router with the NETGEAR genie automatically, or you can use the genie
menus and screens to set up your router manually. Before you start the setup process, get
your ISP information and make sure that the computers and devices in the network use the
settings described here.
Connect to the Network and Access the Router
17
Nighthawk AC1750 Smart WiFi Router
When your Internet service starts, your Internet service provider (ISP) typically gives you all
the information needed to connect to the Internet. For DSL service, you might need the
following information to set up your router:
•
The ISP configuration information for your DSL account
•
ISP login name and password
•
Fixed or static IP address setting (special deployment by ISP; this setting is rare)
If you cannot locate this information, ask your ISP to provide it. When your Internet
connection is working, you no longer need to launch the ISP login program on your computer
to access the Internet. When you start an Internet application, your router automatically logs
you in.
NETGEAR genie runs on any device with a web browser. Installation and basic setup takes
about 15 minutes to complete.

To use NETGEAR genie to set up your router:
1. Turn the router on by pressing the On/Off button.
2. Make sure that your computer or wireless device is connected to the router with an Ethernet
cable (wired) or wirelessly with the preset security settings listed on the label.
Note: If you want to change the router’s WiFi setting, use a wired connection
to avoid being disconnected when the new WiFi settings take effect.
3. Launch an Internet browser.
The screen that displays depends on whether you accessed the router before:
•
The first time you set up the Internet connection for your router, the browser goes to
http://www.routerlogin.net, and the NETGEAR genie screen displays.
•
If you already used the NETGEAR genie, type http://www.routerlogin.net in the
address field for your browser to display. The NETGEAR genie screen displays.
4. Follow the onscreen instructions.
NETGEAR genie guides you through connecting the router to the Internet.
5. If the browser cannot display the web page, do the following:
Connect to the Network and Access the Router
18
Nighthawk AC1750 Smart WiFi Router
•
Make sure that the computer is connected to one of the four LAN Ethernet ports or
wirelessly to the router.
•
Make sure that the Power LED is lights solid white.
•
Close and reopen the browser or clear the browser cache.
•
Browse to http://www.routerlogin.net.
•
If the computer is set to a static or fixed IP address (this setting is uncommon),
change it to obtain an IP address automatically from the router.
6. If the router does not connect to the Internet, do the following:
a. Review your settings. Make sure that you selected the correct options and typed
everything correctly.
b. Contact your ISP to verify that you specified the correct configuration information.
c. Read Chapter 14, Troubleshooting.
If problems persist, register your NETGEAR product and contact NETGEAR technical
support.
Log In to the Router
When you first set up your router, NETGEAR genie automatically starts when you launch an
Internet browser on a computer that is connected to the router. If you want to view or change
settings for the router, you can use genie again.

To log in to the router:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Change the Language
By default, the language is set to Auto.

To change the language:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
Connect to the Network and Access the Router
19
Nighthawk AC1750 Smart WiFi Router
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. In the upper right corner, select a language from the menu.
5. When prompted, click the OK button to confirm this change.
The screen refreshes with the language that you selected.
Access the Router with NETGEAR genie App
The genie app is the easy dashboard for managing, monitoring, and repairing your home
network. The genie app can help you with the following:

•
Automatically repair common wireless network problems.
•
Easily manage router features like Live Parental Controls, guest access, Internet traffic
meter, speed test, and more.
To use the genie app to access the router:
1. Visit the NETGEAR genie web page at www.NETGEAR.com/genie.
2. Follow the onscreen instructions to install the app on your smartphone, tablet, or computer.
3. Launch the genie app.
The genie app dashboard screen displays.
Connect to the Network and Access the Router
20
3.
Specify Your Internet Settings
Usually, the quickest way to set up the router to use your Internet connection is to allow the genie
to detect the Internet connection when you first access the router with an Internet browser. You
can also customize or specify your Internet settings.
This chapter contains the following sections:
•
Use the Internet Setup Wizard
•
Manually Set Up the Internet Connection
•
Specify IPv6 Internet Connections
•
Maximum Transmission Unit
21
Nighthawk AC1750 Smart WiFi Router
Use the Internet Setup Wizard
You can use the Setup Wizard to detect your Internet settings and automatically set up your
router. The Setup Wizard is not the same as the genie screens that display the first time you
connect to your router to set it up.

To use the Setup Wizard:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup Wizard.
5. Select the Yes radio button.
If you select the No radio button, you are taken to the Internet Setup screen (see
Manually Set Up the Internet Connection on page 23).
6. Click the Next button.
Specify Your Internet Settings
22
Nighthawk AC1750 Smart WiFi Router
The Setup Wizard searches your Internet connection for servers and protocols to
determine your ISP configuration.
Manually Set Up the Internet Connection
You can view or change the router’s Internet connection settings.
Specify an Internet Connection Without a Login

To specify the Internet connection settings:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Specify Your Internet Settings
23
Nighthawk AC1750 Smart WiFi Router
4. Select Internet.
5. In the Does your Internet connection require a login section, leave the No radio button
selected.
6. If your Internet connection requires an account name or host name, type it in the Account
Name (If Required) field.
7. If your Internet connection requires a domain name, type it in the Domain Name (If
Required) field.
For the other sections in this screen, the default settings usually work, but you can
change them.
8. Select an Internet IP Address radio button:
• Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your ISP
automatically assigns these addresses.
•
Use Static IP Address. Enter the IP address, IP subnet mask, and gateway IP
address that your ISP assigned. The gateway is the ISP router to which your router
connects.
9. Select a Domain Name Server (DNS) Address radio button:
• Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers. Your
ISP automatically assigns this address.
•
Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
10. Select a Router MAC Address radio button:
• Use Default Address. Use the default MAC address.
Specify Your Internet Settings
24
Nighthawk AC1750 Smart WiFi Router
•
Use Computer MAC Address. The router captures and uses the MAC address of the
computer that you are now using. You must use the one computer that the ISP
allows.
•
Use This MAC Address. Enter the MAC address that you want to use.
11. Click the Apply button.
Your settings are saved.
12. Click the Test button to test your Internet connection.
If the NETGEAR website does not display within one minute, see Chapter 14,
Troubleshooting.
Specify an Internet Connection That Uses a Login

To view or change the basic Internet setup:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Specify Your Internet Settings
25
Nighthawk AC1750 Smart WiFi Router
4. Select Internet.
5. In the Does your Internet connection require a login section, select the Yes radio button.
The screen adjusts.
6. In the Internet Service Provider list, select the encapsulation method: PPPoE, PPPoA, or
L2TP.
7. In the Login field, enter the login name your ISP gave you.
This login name is often an email address.
8. In the Password field, type the password that you use to log in to your Internet service.
9. If your ISP requires a service name, type it in the Service Name (if Required) field.
10. In the Connection Mode list, select Always On, Dial on Demand, or Manually Connect.
11. To change the number of minutes until the Internet login times out, in the Idle Timeout (In
minutes) field, type the number of minutes.
This is how long the router keeps the Internet connection active when no one on the
network is using the Internet connection. A value of 0 (zero) means never log out.
12. Select an Internet IP Address radio button:
• Get Dynamically from ISP. Your ISP uses DHCP to assign your IP address. Your ISP
automatically assigns these addresses.
•
Use Static IP Address. Enter the IP address, IP subnet mask, and gateway IP
address that your ISP assigned. The gateway is the ISP router to which your router
connects.
13. Select a Domain Name Server (DNS) Address radio button:
Specify Your Internet Settings
26
Nighthawk AC1750 Smart WiFi Router
•
Get Automatically from ISP. Your ISP uses DHCP to assign your DNS servers. Your
ISP automatically assigns this address.
•
Use These DNS Servers. If you know that your ISP requires specific servers, select
this option. Enter the IP address of your ISP’s primary DNS server. If a secondary
DNS server address is available, enter it also.
14. Select a Router MAC Address radio button:
• Use Default Address. Use the default MAC address.
•
Use Computer MAC Address. The router captures and uses the MAC address of the
computer that you are now using. You must use the one computer that the ISP
allows.
•
Use This MAC Address. Enter the MAC address that you want to use.
15. Click the Apply button.
Your settings are saved.
16. Click the Test button to test your Internet connection.
If the NETGEAR website does not display within one minute, see Chapter 14,
Troubleshooting.
Specify IPv6 Internet Connections
You can set up an IPv6 Internet connection if genie does not detect it automatically.

To set up an IPv6 Internet connection:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com..
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The Basic Settings screen displays.
5. In the Internet Connection Type list, select the IPv6 connection type:
• If your ISP did not provide details, select IPv6 Tunnel.
•
If you are not sure, select Auto Detect so that the router detects the IPv6 type that is
in use.
•
If your Internet connection does not use PPPoE, DHCP, or fixed, but is IPv6, select
Auto Config.
Specify Your Internet Settings
27
Nighthawk AC1750 Smart WiFi Router
Your Internet service provider (ISP) can provide this information. For more information
about IPv6 Internet connection, see the following sections.
Use Auto Detect for an IPv6 Internet Connection on page 28
Use Auto Config for an IPv6 Internet Connection on page 29
Set Up an IPv6 6to4 Tunnel Internet Connection on page 31
Set Up an IPv6 Pass Through Internet Connection on page 32
Set Up an IPv6 Fixed Internet Connection on page 33
Set Up an IPv6 DHCP Internet Connection on page 35
Set Up an IPv6 PPPoE Internet Connection on page 36
6. Click the Apply button.
Your changes take effect.
Requirements for Entering IPv6 Addresses
IPv6 addresses are denoted by eight groups of hexadecimal quartets that are separated by
colons. You can reduce any four-digit group of zeros within an IPv6 address to a single zero
or omit it. The following errors invalidate an IPv6 address:
•
More than eight groups of hexadecimal quartets
•
More than four hexadecimal characters in a quartet
•
More than two colons in a row
Use Auto Detect for an IPv6 Internet Connection

To set up an IPv6 Internet connection through auto detection:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select Auto Detect.
Specify Your Internet Settings
28
Nighthawk AC1750 Smart WiFi Router
The screen adjusts:
The router automatically detects the information in the following fields:
•
Connection Type. This field indicates the connection type that is detected.
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
6. Select an IP Address Assignment radio button:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your home
network (the LAN).
7. (Optional) Select the Use This Interface ID check box and specify the interface ID to be
used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
8. Click the Apply button.
Your settings are saved.
Use Auto Config for an IPv6 Internet Connection

To set up an IPv6 Internet connection through auto configuration:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
Specify Your Internet Settings
29
Nighthawk AC1750 Smart WiFi Router
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select Auto Config.
The screen adjusts:
The router automatically detects the information in the following fields:
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the length
of the prefix, which is also indicated by the underline (_) under the IPv6 address. If no
address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
6. (Optional) In the DHCP User Class (If Required) field, enter a host name.
Most people can leave this field blank, but if your ISP gave you a specific host name,
enter it here.
7. (Optional) In the DHCP Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. Do not enter the domain name for the
IPv4 ISP here. For example, if your ISP’s mail server is mail.xxx.yyy.zzz, type xxx.yyy.zzz
as the domain name. If your ISP provided a domain name, type it in this field. For
example, Earthlink Cable might require a host name of home, and Comcast sometimes
supplies a domain name.
Specify Your Internet Settings
30
Nighthawk AC1750 Smart WiFi Router
8. Select an IP Address Assignment radio button:
• Use DHCP Server. This method passes more information to LAN devices, but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your home
network (the LAN).
9. (Optional) Select the Use This Interface ID check box and specify the interface ID that you
want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
10. Click the Apply button.
Your settings are saved.
Set Up an IPv6 6to4 Tunnel Internet Connection
The remote relay router is the router to which your router creates a 6to4 tunnel. Make sure
that the IPv4 Internet connection is working before you apply the 6to4 tunnel settings for the
IPv6 connection.

To set up an IPv6 Internet connection by using a 6to4 tunnel:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select 6to4 Tunnel.
Specify Your Internet Settings
31
Nighthawk AC1750 Smart WiFi Router
The screen adjusts:
The router automatically detects the information in the Router’s IPv6 Address on LAN
field. This field shows the IPv6 address that is acquired for the router’s LAN interface. The
number after the slash (/) is the length of the prefix, which is also indicated by the
underline (_) under the IPv6 address. If no address is acquired, the field displays Not
Available.
6. Select a Remote 6to4 Relay Router radio button:
• Auto. Your router uses any remote relay router that is available on the Internet. This
is the default setting.
•
Static IP Address. Enter the static IPv4 address of the remote relay router. Your IPv6
ISP usually provides this address.
7. Select an IP Address Assignment radio button:
• Use DHCP Server. This method passes more information to LAN devices but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your home
network (the LAN).
8. (Optional) Select the Use This Interface ID check box and specify the interface ID to be
used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
9. Click the Apply button.
Your settings are saved.
Set Up an IPv6 Pass Through Internet Connection
In pass-through mode, the router works as a Layer 2 Ethernet switch with two ports (LAN and
WAN Ethernet ports) for IPv6 packets. The router does not process any IPv6 header packets.
Specify Your Internet Settings
32
Nighthawk AC1750 Smart WiFi Router

To set up a pass-through IPv6 Internet connection:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select Pass Through.
The screen adjusts, but no additional fields display.
6. Click the Apply button.
Your settings are saved.
Set Up an IPv6 Fixed Internet Connection

To set up a fixed IPv6 Internet connection:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select Fixed.
Specify Your Internet Settings
33
Nighthawk AC1750 Smart WiFi Router
The screen adjusts:
6. Configure the fixed IPv6 addresses for the WAN connection:
• IPv6 Address/Prefix Length. The IPv6 address and prefix length of the router WAN
interface.
•
Default IPv6 Gateway. The IPv6 address of the default IPv6 gateway for the router’s
WAN interface.
•
Primary DNS Server. The primary DNS server that resolves IPv6 domain name
records for the router.
•
Secondary DNS Server. The secondary DNS server that resolves IPv6 domain
name records for the router.
Note: If you do not specify the DNS servers, the router uses the DNS servers
that are configured for the IPv4 Internet connection on the Internet
Setup screen. (See Manually Set Up the Internet Connection on
page 23.)
7. Select an IP Address Assignment radio button:
• Use DHCP Server. This method passes more information to LAN devices but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your home
network (the LAN).
8. In the IPv6 Address/Prefix Length fields, specify the static IPv6 address and prefix length
of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
9. Click the Apply button.
Your settings are saved.
Specify Your Internet Settings
34
Nighthawk AC1750 Smart WiFi Router
Set Up an IPv6 DHCP Internet Connection

To set up an IPv6 Internet connection with a DHCP server:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select DHCP.
The screen adjusts:
The router automatically detects the information in the following fields:
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
6. (Optional) In the User Class (If Required) field, enter a host name.
Most people can leave this field blank, but if your ISP gave you a specific host name,
enter it here.
Specify Your Internet Settings
35
Nighthawk AC1750 Smart WiFi Router
7. (Optional) In the Domain Name (If Required) field, enter a domain name.
You can type the domain name of your IPv6 ISP. Do not enter the domain name for the
IPv4 ISP here. For example, if your ISP’s mail server is mail.xxx.yyy.zzz, type xxx.yyy.zzz
as the domain name. If your ISP provided a domain name, type it in this field. For
example, Earthlink Cable might require a host name of home, and Comcast sometimes
supplies a domain name.
8. Select an IP Address Assignment radio button:
• Use DHCP Server. This method passes more information to LAN devices but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
This setting specifies how the router assigns IPv6 addresses to the devices on your home
network (the LAN).
9. (Optional) Select the Use This Interface ID check box and specify the interface ID to be
used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
10. Click the Apply button.
Your settings are saved.
Set Up an IPv6 PPPoE Internet Connection

To set up a PPPoE IPv6 Internet connection:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > IPv6.
The IPv6 screen displays.
5. In the Internet Connection Type list, select PPPoE.
Specify Your Internet Settings
36
Nighthawk AC1750 Smart WiFi Router
The screen adjusts:
The router automatically detects the information in the following fields:
•
Router’s IPv6 Address on WAN. This field shows the IPv6 address that is acquired
for the router’s WAN (or Internet) interface. The number after the slash (/) is the
length of the prefix, which is also indicated by the underline (_) under the IPv6
address. If no address is acquired, the field displays Not Available.
•
Router’s IPv6 Address on LAN. This field shows the IPv6 address that is acquired
for the router’s LAN interface. The number after the slash (/) is the length of the prefix,
which is also indicated by the underline (_) under the IPv6 address. If no address is
acquired, the field displays Not Available.
6. In the Login field, enter the login information for the ISP connection.
This is usually the name that you use in your email address. For example, if your main
mail account is JerAB@ISP.com, you would type JerAB in this field. Some ISPs (like
Mindspring, Earthlink, and T-DSL) require that you use your full email address when you
log in. If your ISP requires your full email address, type it in this field.
7. In the Password field, enter the password for the ISP connection.
8. In the Service Name field, enter a service name.
If your ISP did not provide a service name, leave this field blank.
Note: The default setting of the Connection Mode field is Always On to
provide a steady IPv6 connection. The router never terminates the
connection. If the connection is terminated, for example, when the
modem is turned off, the router attempts to reestablish the connection
immediately after the PPPoE connection becomes available again.
9. Select an IP Address Assignment radio button:
• Use DHCP Server. This method passes more information to LAN devices but some
IPv6 systems might not support the DHCv6 client function.
•
Auto Config. This is the default setting.
Specify Your Internet Settings
37
Nighthawk AC1750 Smart WiFi Router
This setting specifies how the router assigns IPv6 addresses to the devices on your home
network (the LAN).
10. (Optional) Select the Use This Interface ID check box and specify the interface ID to be
used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.
11. Click the Apply button.
Your settings are saved.
Maximum Transmission Unit
The maximum transmission unit (MTU) is the largest data packet a network device transmits.
When one network device communicates across the Internet with another, the data packets
travel through many devices along the way. If a device in the data path uses a lower MTU
setting than the other devices, the data packets must be split or “fragmented” to
accommodate the device with the smallest MTU.
The best MTU setting for NETGEAR equipment is often the default value. In some situations,
changing the value fixes one problem but causes another. Leave the MTU unchanged unless
one of these situations occurs:
•
You experience problems connecting to your ISP or other Internet service, and the
technical support of either the ISP or NETGEAR recommends changing the MTU setting.
These web-based applications might require an MTU change:
A secure website that does not open, or displays only part of a web page
Yahoo email
MSN portal
America Online’s DSL service
•
You use VPN and have severe performance problems.
•
You used a program to optimize MTU for performance reasons, and now you have
connectivity or performance problems.
Note: An incorrect MTU setting can cause Internet communication
problems. For example, you might not be able to access certain
websites, frames within websites, secure login pages, or FTP or POP
servers.
Specify Your Internet Settings
38
Nighthawk AC1750 Smart WiFi Router
Change the MTU Size

To change the MTU size:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup > WAN Setup.
5. In the MTU Size field, enter a value from 64 to 1500.
6. Click the Apply button.
Your change is saved.
Common MTU Sizes
If you suspect an MTU problem, a common solution is to change the MTU to 1400. If you are
willing to experiment, you can gradually reduce the MTU from the maximum value of 1500
until the problem goes away. The following table describes common MTU sizes and
applications.
Table 2. Common MTU sizes
MTU
Application
1500
The largest Ethernet packet size. This setting is typical for connections that do not use
PPPoE or VPN, and is the default value for NETGEAR routers, adapters, and switches.
1492
Used in PPPoE environments.
1472
Maximum size to use for pinging. (Larger packets are fragmented.)
Specify Your Internet Settings
39
Nighthawk AC1750 Smart WiFi Router
Table 2. Common MTU sizes (continued)
MTU
Application
1468
Used in some DHCP environments.
1460
Usable by AOL if you do not use large email attachments, for example.
1436
Used in PPTP environments or with VPN.
1400
Maximum size for AOL DSL.
576
Typical value to connect to dial-up ISPs.
Specify Your Internet Settings
40
4.
Optimize Performance
You can set up the router to optimize performance for applications such as multiplayer gaming,
peer-to-peer connections, or real-time communications such as instant messaging or remote
assistance (a feature in Windows XP). By default, the router uses Wi-Fi Multimedia Quality of
Service (WMM QoS).
This chapter contains the following sections:
•
Prioritize Internet Traffic with Quality of Service
•
Optimize Internet Gaming with Upstream QoS
•
Add Upstream QoS Rules
•
Optimize Video Streaming with Downstream QoS
•
Improve Network Connections with Universal Plug and Play
•
Wi-Fi Multimedia Quality of Service
41
Nighthawk AC1750 Smart WiFi Router
Prioritize Internet Traffic with Quality of Service
You can use Quality of Service (QoS) to assign a high priority to gaming and streaming video
from the Internet.
Downstream QoS
(video streaming)
Internet
Upstream QoS
(gaming)
Figure 6. You can prioritize downstream traffic, upstream traffic, or both
Optimize Internet Gaming with Upstream QoS
Upstream Quality of Service (QoS) assigns a high priority to Internet traffic from your Xbox
gaming system.
High priority traffic
Internet
Best efort traffic
Figure 7. Upstream QoS assigns high priority to gaming traffic from your Xbox
NETGEAR recommends that only gamers enable the Upstream QoS feature. If you do not
game and you turn on this feature, some applications might not perform as well as usual.
Optimize Performance
42
Nighthawk AC1750 Smart WiFi Router

To enable upstream QoS:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup > QoS Setup > Upstream QoS.
5. Select the Enable Upstream QoS (Optimized for Gaming) check box.
6. Specify the maximum uplink bandwidth for your Internet connection:
• If you know what your uplink bandwidth is, type it in the Uplink bandwidth Maximum
field.
•
If you are not sure, click the Speedtest button.
Speedtest verifies the upstream speed of your Internet connection. The Uplink
bandwidth Maximum field displays the result of the test.
7. Click the Apply button.
The router assigns a high priority to Internet traffic from your gaming devices to the
Internet.
Add Upstream QoS Rules
You can give prioritized Internet access to the following types of traffic:
•
Specific applications
•
Specific online games
•
Individual Ethernet LAN ports of the router
•
A specific device by MAC address
Optimize Performance
43
Nighthawk AC1750 Smart WiFi Router
To specify prioritization of traffic, create a policy for the type of traffic and add the policy to the
QoS Policy table in the QoS Setup screen. For convenience, the QoS Policy table lists many
common applications and online games that can benefit from QoS handling.
Set Up QoS for Applications and Online Gaming

To create a QoS policy for applications and online games:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup > QoS Setup > Upstream QoS.
5. Click the Setup QoS rule button.
Optimize Performance
44
Nighthawk AC1750 Smart WiFi Router
The QoS Priority Rule list displays.
6. To add a priority rule, scroll down to the bottom of the QoS Setup screen and click the Add
Priority Rule button.
7. In the QoS Policy for field, type the name of the application or game.
8. In the Priority Category list, select either Applications or Online Gaming.
A list of applications or games displays.
9. Scroll and select Add a New Application or Add a New Game, as applicable.
10. If prompted, in the Connection Type list, select either TCP, UDP, or TCP/UDP (both).
11. Specify the port number or range of port numbers that the application or game uses.
12. From the Priority list, select the priority for Internet access for this traffic relative to other
applications and traffic.
The options are Low, Normal, High, and Highest.
13. Click the Apply button.
The rule is saved.
Optimize Performance
45
Nighthawk AC1750 Smart WiFi Router
Set Up QoS for a Router LAN Port

To create a QoS policy for a device connected to one of the router’s LAN ports:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays
4. Select ADVANCED > Setup > QoS Setup.
The QoS Setup screen displays.
5. Select the Turn Internet Access QoS On check box.
6. Select ADVANCED > Setup > QoS Setup > Upstream QoS.
7. Click the Setup QoS Rule button.
The QoS Priority Rule list displays.
8. Scroll down and click the Add Priority Rule button.
The QoS - Priority Rules screen displays.
9. From the Priority Category list, select Ethernet LAN Port.
10. From the QoS Policy for list, select the LAN port.
11. From the Priority list, select the priority for Internet access for this port’s traffic relative to
other applications.
Optimize Performance
46
Nighthawk AC1750 Smart WiFi Router
The options are Low, Normal, High, and Highest.
12. Click the Apply button.
The rule is saved in the QoS Policy list.
Set Up QoS for a MAC Address

To create a QoS policy for traffic from a specific MAC address:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup > QoS Setup > Upstream QoS.
5. Click the Setup QoS Rule button.
The QoS Priority Rule list displays.
6. Scroll down and click the Add Priority Rule button.
The QoS - Priority Rules screen displays.
Optimize Performance
47
Nighthawk AC1750 Smart WiFi Router
7. From the Priority Category list, select MAC Address.
8. If the device is in the MAC Device List, select its radio button.
The information from the MAC Device List populates the QoS Policy for, MAC Address,
and Device Name fields. If the device is not in the MAC Device List, click the Refresh
button. If it still does not display, complete these fields.
9. From the Priority list, select Highest.
This is the priority for Internet access for this device’s traffic relative to other applications
and traffic. The options are Low, Normal, High, and Highest.
10. Click the Apply button.
This rule is saved.
Edit an Upstream QoS Policy

To edit a QoS policy:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Optimize Performance
48
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Setup > QoS Setup > Upstream QoS.
5. Click the Setup QoS Rule button.
The QoS Priority Rule list displays.
6. Select the radio button for the QoS policy.
7. Scroll down and click the Edit button.
8. Change the policy settings.
9. Click the Apply button.
Your changes are saved.
Delete an Upstream QoS Policy

To delete a QoS policy:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup > QoS Setup > Upstream QoS.
5. Click the Setup QoS Rule button.
The QoS Priority Rule list displays.
Optimize Performance
49
Nighthawk AC1750 Smart WiFi Router
6. Select the radio button for the QoS policy.
7. Click the Delete button.
The QoS Policy is removed from the list.
Optimize Video Streaming with Downstream QoS
Downstream Quality of Service (QoS) assigns a high priority to Internet video streaming from
websites like YouTube and Netflix.
High priority traffic
Internet
Best efort traffic
Figure 8. Downstream QoS assigns a high priority to video streaming from the Internet
NETGEAR recommends that you enable downstream QoS only if you watch streaming
Internet video. When downstream QoS assigns a high priority to streaming video, it also
assigns a lower priority to the rest of your Internet traffic. That means other tasks like
downloading content from the Internet take longer.

To enable downstream QoS:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Optimize Performance
50
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Setup > QoS Setup > Downstream QoS.
5. Select the Enable Downstream QoS (Improved Video Streaming) check box.
6. (Optional) Select the Streaming Database Auto Upgrade check box.
The router automatically checks for updates for the streaming database, and downloads
and installs them.
7. Click the Apply button.
The router assigns a high priority to video streaming from the Internet traffic.
Add Downstream QoS Rules by Keyword

To add a downstream QoS rule by keyword:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Optimize Performance
51
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Setup > QoS Setup > Downstream QoS.
5. Select the Enable Downstream QoS (Improved Video Streaming) check box.
6. In the Add Rules section, leave the by Keyword radio button selected.
7. In the Rule Name field, type the name of the rule.
8. In the Keyword field, type a keyword.
9. Click the Add button.
The rule is added to the QoS rules. The router assigns a high priority to Internet traffic
from the server that matches the keyword.
Add a Downstream QoS Rule by Device

To add a downstream QoS rule by keyword:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Optimize Performance
52
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Setup > QoS Setup > Downstream QoS.
5. Select the Enable Downstream QoS (Improved Video Streaming) check box.
6. In the Add Rules section, select the by Device radio button.
The screen adjusts.
7. In the MAC Device list, select a radio button for a device.
8. Click the Add button.
The router assigns a high priority to streaming traffic that goes from the Internet to the
device you specified.
Improve Network Connections with Universal Plug and
Play
Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers,
access the network and connect to other devices as needed. UPnP devices can
automatically discover the services from other registered UPnP devices on the network.
If you use applications such as multiplayer gaming, peer-to-peer connections, or real-time
communications such as instant messaging or remote assistance (a feature in Windows XP),
enable UPnP.

To enable Universal Plug and Play:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
Optimize Performance
53
Nighthawk AC1750 Smart WiFi Router
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > UPnP.
The UPnP screen displays.
5. Select the Turn UPnP On check box.
By default, this check box is selected. UPnP for automatic device configuration can be
enabled or disabled. If the Turn UPnP On check box is cleared, the router does not allow
any device to automatically control router resources, such as port forwarding.
6. Type the advertisement period in minutes.
The advertisement period specifies how often the router broadcasts its UPnP information.
This value can range from 1 to 1440 minutes. The default period is 30 minutes. Shorter
durations ensure that control points provide current device status at the expense of more
network traffic. Longer durations can compromise the freshness of the device status, but
can significantly reduce network traffic.
7. Type the advertisement time to live in hops.
The time to live for the advertisement is measured in hops (steps) for each UPnP packet
sent. Hops are the steps a packet takes between routers. The number of hops can range
from 1 to 255. The default value for the advertisement time to live is 4 hops, which is fine
for most home networks. If you notice that some devices are not being updated or
reached correctly, it might be necessary to increase this value.
8. Click the Apply button.
The UPnP Portmap Table displays the IP address of each UPnP device that is accessing
the router and which ports (internal and external) that device opened. The UPnP Portmap
Table also displays what type of port is open and whether that port is still active for each
IP address.
To refresh the information in the UPnP Portmap Table, click the Refresh button.
Wi-Fi Multimedia Quality of Service
Wi-Fi Multimedia Quality of Service (WMM QoS) prioritizes wireless voice and video traffic
over the WiFi link. WMM QoS is automatically enabled for the router.
WMM QoS prioritizes wireless data packets from different applications based on four access
categories: voice, video, best effort, and background. For an application to receive the
benefits of WMM QoS, WMM must be enabled for both it and the client running that
application. Legacy applications that do not support WMM and applications that do not
require QoS are assigned to the best effort category, which receives a lower priority than
voice and video.
Optimize Performance
54
Nighthawk AC1750 Smart WiFi Router

To disable WMM QoS:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Setup > QoS Setup.
The QoS Setup screen displays.
5. Clear the Enable WMM (Wi-Fi multimedia) settings (2.4 GHz b/g/n) check box.
6. Clear the Enable WMM (Wi-Fi multimedia) settings (5 GHz b/g/n) check box.
7. Click the Apply button.
Your changes are saved.
Optimize Performance
55
5.
Control Access to the Internet
The router comes with a built-in firewall that helps protect your home network from unwanted
intrusions from the Internet.
This chapter includes the following sections:
•
Set Up Parental Controls
•
Control Access to Your Network
•
Use Keywords to Block Internet Sites
•
Block Services from the Internet
•
Schedule When to Block Internet Sites and Services
•
Avoid Blocking on a Trusted Computer
•
Set Up Security Event Email Notifications
56
Nighthawk AC1750 Smart WiFi Router
Set Up Parental Controls
The first time that you select Parental Controls from the BASIC Home screen, your browser
goes to the Live Parental Controls website, where you can learn more about Live Parental
Controls and download the application.

To set up Live Parental Controls:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select Parental Controls.
If your Internet connection is working, the browser automatically goes online and displays
the Parental Controls web page.
5. Click either the Windows Users or Mac Users button.
6. Follow the onscreen instructions to download and install the NETGEAR Live Parental
Controls management utility.
Control Access to the Internet
57
Nighthawk AC1750 Smart WiFi Router
After installation, Live Parental Controls automatically starts.
7. Click the Next button.
8. Read the note, and click the Next button again.
Because Live Parental Controls uses free OpenDNS accounts, you are prompted to log
in or create a free account.
9. Select the radio button that applies to you:
• If you already set up an OpenDNS account, leave the Yes radio button selected.
•
If you did not set up an OpenDNS account, select the No radio button.
10. Click the Next button.
If you are creating an account, the following screen displays:
Control Access to the Internet
58
Nighthawk AC1750 Smart WiFi Router
11. Complete the fields and click the Next button.
After you log on or create your account, the filtering level screen displays:
12. Select a radio button for a filtering level and click the Next button.
13. Click the Take me to the status screen button.
Parental controls are now set up for the router. The dashboard shows Parental Controls as
Enabled.
Control Access to Your Network
You can use access control to allow or block access to your network.

To set up access control:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
Control Access to the Internet
59
Nighthawk AC1750 Smart WiFi Router
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Security > Access Control.
The Access Control screen displays.
5. Select the Turn on Access Control check box.
You must select this check box before you can specify an access rule and use the Allow
and Block buttons. When this check box is cleared, all devices are allowed to connect,
even if the device is in the blocked list.
6. Select an access rule:
• Allow all new devices to connect. With this setting, if you buy a new device, it can
access your network. You don’t need to enter its MAC address in this screen.
NETGEAR recommends that you leave this radio button selected.
•
Block all new devices from connecting. With this setting, if you buy a new device,
before it can access your network, you must enter its MAC address for an Ethernet
connection and its MAC address for a WiFi connection in the allowed list.
The access rule does not affect previously blocked or allowed devices. It applies only to
devices joining your network in the future after you apply these settings.
7. To allow the computer or device you’re currently using to continue to access the network,
select the check box next to your computer or device, and click the Allow button.
8. Click the Apply button.
Your changes take effect.
Use Keywords to Block Internet Sites
You can use keywords to block certain Internet sites from your network. You can use
blocking continuously or based on a schedule.

To block Internet sites:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Control Access to the Internet
60
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Security > Block Sites.
5. Select a keyword blocking option:
• Per Schedule. Turn on keyword blocking according to a schedule that you set. (See
Schedule When to Block Internet Sites and Services on page 64.)
•
Always. Turn on keyword blocking all the time, independent of the Schedule screen.
6. In the keyword field, enter a keyword or domain that you want to block.
For example:
•
Specify XXX to block http://www.badstuff.com/xxx.html.
•
Specify .com if you want to allow only sites with domain suffixes such as .edu or .gov.
•
Enter a period (.) to block all Internet browsing access.
7. Click the Add Keyword button.
The keyword is added to the keyword list. The keyword list supports up to 32 entries.
8. Click the Apply button.
Keyword blocking takes effect.
Delete Keywords from the List to Be Blocked

To delete keywords from the list:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
Control Access to the Internet
61
Nighthawk AC1750 Smart WiFi Router
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Security > Block Sites.
5. Do one of the following:
• To delete a single word, select it and click the Delete Keyword button.
The keyword is removed from the list.
•
To delete all keywords on the list, click the Clear List button.
All keywords are removed from the list.
6. Click the Apply button.
Your changes are saved.
Block Services from the Internet
You can block Internet services on your network based on the type of service. You can block
the services all the time or based on a schedule.

To block services:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
Control Access to the Internet
62
Nighthawk AC1750 Smart WiFi Router
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Security > Block Services.
The Block Services screen displays.
5. Specify when to block the services:
• To block the services all the time, select the Always radio button.
•
To block the services based on a schedule, select the Per Schedule radio button.
For more information about how to specify the schedule, see Schedule When to Block
Internet Sites and Services on page 64.
6. Click the Add button.
The Block Services Setup screen displays:
7. To add a service that is in the Service Type list, select the application or service.
The settings for this service automatically display in the fields.
8. To add a service or application that is not the list, select User Defined and do the following.
a. If you know that the application uses either TCP or UDP, select the appropriate
protocol; otherwise, select TCP/UDP (both).
b. Enter the starting port and ending port numbers.
If the service uses a single port number, enter that number in both fields.
To find out which port numbers the service or application uses, you can contact the
publisher of the application, ask user groups or newsgroups, or search on the
Internet.
9. Select a filtering option:
• Only This IP Address. Block services for a single computer.
•
IP Address Range. Block services for a range of computers with consecutive IP
addresses on your network.
•
All lP Addresses. Block services for all computers on your network.
10. Click the Add button.
Your changes are saved.
Control Access to the Internet
63
Nighthawk AC1750 Smart WiFi Router
Schedule When to Block Internet Sites and Services
When you schedule blocking, the same schedule is used to block sites and to block services.
For information about how to specify what you want the router to block, see Use Keywords to
Block Internet Sites on page 60 and Block Services from the Internet on page 62.

To schedule blocking:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Security > Schedule.
The Schedule screen displays.
5. Specify when to block keywords and services:
• Days to Block. Select the check box for each day that you want to block the
keywords or select the Every Day check box, which automatically selects the check
boxes for all days.
•
Time of Day to Block. Select a start and end time in 24-hour format or select All Day
for 24-hour blocking.
6. Select your time zone from the list.
7. If you live in a region that observes daylight saving time, select the Automatically adjust for
daylight savings time check box.
8. Click the Apply button.
Your settings are saved.
Avoid Blocking on a Trusted Computer
You can exempt one trusted computer from blocking. The computer you exempt must use a
fixed IP address. You can use the reserved IP address feature to specify the IP address. See
Reserve LAN IP Addresses on page 111.

To specify a trusted computer:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
Control Access to the Internet
64
Nighthawk AC1750 Smart WiFi Router
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Security > Block Sites.
The Block Sites screen displays.
5. Scroll down and select the Allow trusted IP address to visit blocked sites check box.
6. In the Trusted IP Address field, enter the IP address of the trusted computer.
7. Click the Apply button.
Your changes are saved.
Set Up Security Event Email Notifications
The router can email you its logs of router activity. The log records router activity and security
events such as attempts to access blocked sites or services.

To set up email notifications:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Control Access to the Internet
65
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Security > E-mail.
5. Select the Turn E-mail Notification On check box.
6. In the Your Outgoing Mail Server field, enter the name of your ISP outgoing (SMTP) mail
server (such as mail.myISP.com).
You might be able to find this information in the configuration screen of your email
program. If you leave this field blank, log and alert messages are not sent.
7. In the Send to This E-mail Address field, type the email address to which logs and alerts
are sent.
This email address is also used for the From address. If this field is blank, log and alert
messages are not sent.
8. If your outgoing email server requires authentication, select the My Mail Server requires
authentication check box and do the following.
a. In the User Name field, type the user name for the outgoing email server.
b. In the Password field, type the password for the outgoing email server.
9. To have email alerts sent immediately when someone attempts to visit a blocked site, select
the Send Alerts Immediately check box.
10. To send logs based on a schedule, specify these settings:
• From Send logs according to this schedule list, select the schedule type.
•
From the Day list, select the day.
•
From the Time list, select the time, and select the am or pm radio button.
11. Click the Apply button.
Your settings are saved.
Logs are sent automatically according to the schedule you set. If the log fills before the
specified time, it is sent. After the log is sent, it is cleared from the router memory. If the
router cannot email the log and the log buffer fills, the router overwrites the log.
Control Access to the Internet
66
6.
Share USB Drives Attached to the
Router
This chapter describes how to access and configure USB storage devices attached to your
router. The USB port on the router can be used only to connect USB storage devices like flash
drives or hard drives or a printer. Do not connect computers, USB modems, CD drives, or DVD
drives to the router USB port.
This chapter contains the following sections:
•
USB Drive Requirements
•
Access a USB Device on the Network
•
Back Up Windows Computers with ReadySHARE Vault
•
Back Up Mac Computers with Time Machine
•
Control Access to the USB Drive
•
Use FTP Within the Network
•
View Network Folders on a USB Drive
•
Add a Network Folder on a USB Drive
•
Edit a Network Folder on a USB Drive
•
Approve USB Devices
•
Safely Remove a USB Drive
For more information about ReadySHARE features, visit www.netgear.com/readyshare.
67
Nighthawk AC1750 Smart WiFi Router
USB Drive Requirements
The router works with most USB-compliant external flash and hard drives. For the most
up-to-date list of USB drives that the router supports, visit
http://kbserver.netgear.com/readyshare.
Some USB external hard drives and flash drives require you to load the drivers onto the
computer before the computer can access the USB device. Such USB devices do not work
with the router.
The router supports the following file system types for full read/write access:
•
FAT16
•
FAT32
•
NTFS
•
NTFS with compression format enabled
•
EXT2
•
EXT3
•
EXT4
•
XFS
•
HFS
•
HFS+
Access a USB Device on the Network
ReadySHARE lets you access and share a USB device connected to the router USB port. (If
your USB drive uses special drivers, it is not compatible.)
USB 3.0 port
Figure 9. The blue USB 3.0 port on the front of the router provides the fastest access
Share USB Drives Attached to the Router
68
Nighthawk AC1750 Smart WiFi Router

To connect a USB device:
1. Insert your USB storage device into the blue USB 3.0 port on the front of the router.
2. If your USB device uses a power supply, connect it.
You must use it when you connect the USB device to the router.
When you connect the USB device to the router USB port, it might take up to two minutes
before it is ready for sharing. By default, the USB device is available to all computers on
your local area network (LAN).

To access the USB device from a Mac:
1. Select Go > Connect to Server.
2. Enter smb://readyshare as the server address.
3. Click the Connect button.
4. When prompted, select the Guest radio button.
If you set up access control and you allowed your Mac to access the network, select the
Registered User radio button and enter admin for the name and password for the
password. For more information about access control, see Control Access to Your
Network on page 59.
5. Click the Connect button.
The USB device displays.

To access the USB device from a Windows computer:
1. Select Start > Run.
2. Enter \\readyshare in the dialog box.
3. Click the OK button.
The USB device displays.

To map the USB device to a Windows network drive:
1. Visit www.netgear.com/readyshare.
2. In the ReadySHARE USB Storage Access pane, click the PC Utility link.
The readyshareconnect.exe file is downloaded to your computer.
Share USB Drives Attached to the Router
69
Nighthawk AC1750 Smart WiFi Router
3. Launch readyshareconnect.exe.
4. Select the drive letter to map to the network folder.
5. To connect to the USB drive as a different user, select the Connect using different
credentials check box and do the following:
a. Type the user name and password.
b. Click the OK button.
6. Click the Finish button.
The USB drive is mapped to the drive letter that you specified.
Back Up Windows Computers with ReadySHARE Vault
Your router comes with free backup software for all the Windows computers in your home.
Connect a USB hard disk drive (HDD) to the USB port on your router for centralized,
continuous, and automatic backup.

To back up your Windows computer:
1. Insert your USB storage device into the blue USB 3.0 port on the front of the router.
If your USB device uses a power supply, connect it.
You must use it when you connect the USB device to the router.
When you connect the USB device to the router USB port, it might take up to two minutes
before it is ready for sharing. By default, the USB device is available to all computers on
your local area network (LAN).
2. Install the genie app on each Windows computer.
To download the genie app, visit www.netgear.com/genie.
3. Download ReadySHARE Vault from www.netgear.com/readyshare and install it on each
Windows computer.
4. Launch ReadySHARE Vault.
Share USB Drives Attached to the Router
70
Nighthawk AC1750 Smart WiFi Router
5. Use the dashboard or the Backup tab to set up and run your backup.
Back Up Mac Computers with Time Machine
You can use Time Machine to back up your Mac computers onto a USB hard drive that is
connected to one of the router’s USB ports. You can access the connected USB hard drive
from your Mac with a wired or wireless connection to your router.
Set Up a USB Hard Drive on a Mac
NETGEAR recommends that you use a new USB HDD or format your old USB disk to do the
Time Machine backup for the first time. Use a blank partition to prevent some issues during
backup using Time Machine. The router supports GUID or MBR partitions.

To format your USB hard disk drive and specify partitions:
1. Physically connect the USB hard drive to your Mac.
2. On your Mac, go to Spotlight (or the magnifying glass) at the top right of the screen and
search for Disk Utility.
3. To format your USB drive, open the Disk Utility, click the Erase tab, and click the Erase
button.
4. Click the Partition tab.
5. Click Partition Layout and set the number of partitions that you want to use.
6. Click the Options button.
The Partition options display.
7. Select the GUID Partition Table or Master Boot Record radio button.
8. For the format, select Mac OS Extended (Journaled).
9. Click the OK button.
10. Click the Apply button.
Your settings are saved.
Prepare to Back Up a Large Amount of Data
Before you back up a large amount of data with Time Machine, NETGEAR recommends that
you follow this procedure.

To prepare to back up a large amount of data:
1. Upgrade the operating system of the Mac computer.
2. Verify and repair the backup disk and the local disk.
3. Verify and repair the permissions on the local disk.
4. Set Energy Saver:
Share USB Drives Attached to the Router
71
Nighthawk AC1750 Smart WiFi Router
a. From the Apple menu, select System Preferences.
b. From the View menu, select Energy Saver.
c. Click the Power Adapter tab.
d. Select the Wake for Wi-Fi network access check box.
e. Click the Back arrow to save the changes and exit the screen.
5. Modify your security settings:
a. From the Apple menu, select System Preferences.
b. From the View menu, select Security.
c. Click the Advanced button at the bottom of the screen.
d. Leave the Log out after minutes of inactivity check box cleared.
Use Time Machine to Back Up onto a USB Hard Drive
You can use Time Machine to back up your Mac computers onto a USB hard disk drive that
is connected to one of the router’s USB ports.

To back up your Mac onto a USB hard drive:
1. Prepare your USB drive with a compatible format and partitions.
See Set Up a USB Hard Drive on a Mac on page 71.
If you plan to back up a large amount of data, see Prepare to Back Up a Large Amount of
Data on page 71.
2. Insert your USB storage drive into a USB port on the router.
Note: If your USB drive includes a power supply, you must use it when you
connect the USB drive to the router.
The blue USB 3.0 port on the front of the router performs faster than the USB 2.0 port on
the rear panel of the router.
When you connect the USB drive to the router USB port, it might take up to two minutes
before it is ready for sharing. By default, the USB drive is available to all computers on
your local area network (LAN).
3. On your Mac computer, select Go > Connect to Server.
4. Type afp://routerlogin.net.
5. When prompted to enter your name and password, select the Guest radio button.
6. Click the Connect button.
A list of connected devices displays. This list includes the name admin when you log in as
admin.
7. From the Apple menu, select System Preferences.
8. Open Time Machine.
Share USB Drives Attached to the Router
72
Nighthawk AC1750 Smart WiFi Router
9. Click the Select Backup Disk button and select your USB drive from the list.
10. Click the Use for Backup button.
Note: If you do not see the USB partition that you want in the Time Machine
disk list, go to Mac finder and click that USB partition. It displays in the
Time Machine list.
11. When prompted to enter your name and password, select the Guest radio button and click
the Connect button.
When the setup is complete, the Mac automatically schedules a full back up. You can back
up immediately if you want.
Control Access to the USB Drive
You can specify the device name, workgroups, and network folders for your USB device.

To specify the USB access settings:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > USB Storage > Advanced Settings.
Share USB Drives Attached to the Router
73
Nighthawk AC1750 Smart WiFi Router
5. Specify access to the USB storage device:
• Network Device Name. This is the name used to access the USB device connected
to the router. The default is readyshare.
•
Workgroup. If you are using a Windows workgroup rather than a domain, the
workgroup name is displayed here. The name works only in an operating system that
supports NetBIOS, such as Microsoft Windows.
•
Access Method. Select the check boxes for the access methods that you want:
Network Neighborhood/MacShare. Enabled by default.
HTTP. Enabled by default. You can type
http://readyshare.routerlogin.net/shares to access the USB drive.
HTTP (via Internet). Disabled by default. If you enable this feature, remote users
can type http:// (for example, http://1.1.10.102/shares)
or a URL domain name to access the USB drive over the Internet. This feature
supports file uploading only.
FTP. Disabled by default.
FTP (via Internet). Disabled by default. If you select this check box, remote users
can access the USB drive through FTP over the Internet. This feature supports
both downloading and uploading of files.
6. If you changed the settings, click the Apply button.
Your changes are saved.
Use FTP Within the Network
File Transfer Protocol (FTP) lets you send and receive large files faster.

To set up FTP access:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Share USB Drives Attached to the Router
74
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > USB Storage > Advanced Settings.
5. Select the FTP check box.
6. Click the Apply button.
Your changes are saved.
View Network Folders on a USB Drive
You can view or change the network folders on the USB storage device.

To view or change network folders:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Share USB Drives Attached to the Router
75
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > USB Storage > Advanced Settings.
5. Scroll down to the Available Networks Folder section, and adjust the following settings:
• Share Name. If only one device is connected, the default share name is
USB_Storage. (Some router models include more than one USB port.)
You can click the name, or you can type it in the address field of your web browser. If
Not Shared is shown, the default share was deleted, and no other share for the root
folder exists. Click the link to change this setting.
•
Read Access and Write Access. Show the permissions and access controls on the
network folder. All–no password (the default) allows all users to access the network
folder. The password for admin is the same one that you use to log in to the router.
•
Folder Name. Full path of the network folder.
•
Volume Name. Volume name from the storage device (either USB drive or HDD).
•
Total Space and Free Space. Show the current utilization of the storage device.
Add a Network Folder on a USB Drive
You can edit network folders on the USB storage device.

To add a network folder:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
Share USB Drives Attached to the Router
76
Nighthawk AC1750 Smart WiFi Router
The BASIC Home screen displays.
4. Select ADVANCED > USB Storage > Advanced Settings.
The USB Storage (Advanced Settings) screen displays.
5. Click the Create Network Folder button.
If this screen does not display, your web browser might be blocking pop-ups. If it is,
change the browser settings to allow pop-ups.
6. In the USB Device list, select the USB drive.
7. Click the Browse button and in the Folder field, select the folder.
8. In the Share Name field, type the name of the share.
9. In the Read Access list and the Write Access list, select the settings that you want.
The user name (account name) for All–no password is guest. The password for admin is
the same one that is used to log in to the router. By default, it is password.
10. Click the Apply button.
The folder is added on the USB device.
Edit a Network Folder on a USB Drive
You can add network folders on the USB storage device.

To edit a network folder:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Share USB Drives Attached to the Router
77
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > USB Storage > Advanced Settings.
The USB Storage (Advanced Settings) screen displays.
5. Click the Edit button.
The Edit Network Folder screen displays the same settings shown in the Add a Network
Folder screen.
6. Change the settings in the fields as needed.
7. Click the Apply button.
Your changes are saved.
Approve USB Devices
For more security, you can set up the router to share only USB devices that you approve.

To approve USB devices:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Setup > USB Settings.
By default the Enable any USB Device connection to the USB port radio button is
selected. This setting lets you connect and access all your USB drives.
5. Select the No radio button.
Share USB Drives Attached to the Router
78
Nighthawk AC1750 Smart WiFi Router
6. Click the Approved Devices button.
The approved and available USB devices display.
7. In the Available USB Devices list, select the drive that you want to approve.
8. Click the Add button.
The USB device is added to the Approved USB Devices list.
9. Select the Allow only approved devices check box.
10. Click the Apply button.
Your change takes effect.
11. To work with another USB device, first click the Safely Remove USB Device button for the
currently connected USB device.
Connect the other USB device, and repeat this process.
Safely Remove a USB Drive
Before you physically disconnect a USB drive from the router USB port, log in to the router
and take the drive offline.

To remove a USB disk drive safely:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Share USB Drives Attached to the Router
79
Nighthawk AC1750 Smart WiFi Router
4. Select USB Storage > Basic Settings.
The USB Settings screen displays.
5. Click the Safely Remove USB Device button.
This takes the drive offline.
6. Physically disconnect the USB drive.
Share USB Drives Attached to the Router
80
7.
Access the Router’s USB Drive
Through the Internet
With Dynamic DNS, you can use the Internet to access a USB hard drive attached to the router’s
USB port router when you’re not home. This chapter includes the following sections:
•
Access the USB Drive Through the Internet
•
Dynamic DNS
•
Your Personal FTP Server
•
Set Up Your Personal FTP Server
For information about how to connect the USB drive and specify its settings, see Chapter 6,
Share USB Drives Attached to the Router.
81
Nighthawk AC1750 Smart WiFi Router
Access the USB Drive Through the Internet
You can access the USB drive through the Internet when you’re not home.

To access the USB drive from a remote computer:
1. Launch a web browser on a computer that is not on your home network.
2. Connect to your home router:
• To connect with Dynamic DNS, type the DNS name.
To use a Dynamic DNS account, you must enter the account information in the
Dynamic DNS screen. See Dynamic DNS on page 84.
•
To connect without Dynamic DNS, type the router’s Internet port IP address.
You can view the router’s Internet IP address on the BASIC Home screen.
You can use FTP to share files on a USB drive connected to the router.
Set Up FTP Access Through the Internet

To set up FTP access:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Access the Router’s USB Drive Through the Internet
82
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > USB Storage > Advanced Settings.
5. Select the FTP (via Internet) check box.
6. Click the Apply button.
Your changes are saved.
7. To limit access to the admin user, click the Edit button.
8. In the Read Access list, select admin.
9. In the Write Access list, select admin.
10. Click the Apply button.
Your changes are saved.
Access the USB Drive Through the Internet with FTP
You must first set up FTP through Internet access as described in Set Up FTP Access
Through the Internet on page 82.

To access the USB drive with FTP from a remote computer:
1. Do one of the following:
Access the Router’s USB Drive Through the Internet
83
Nighthawk AC1750 Smart WiFi Router
•
To download, launch an Internet browser.
•
To upload, use an FTP client such as filezilla.
2. Type ftp:// and the Internet port IP address in the address field of the browser.
For example, type ftp://10.1.65.4.
If you are using Dynamic DNS, type the DNS name.
For example, type ftp://MyName.mynetgear.com.
3. When prompted, log in:
• To log in as admin, in the user name field, type admin and in the password field,
type the same password that you use to log in to the router.
•
To log in as guest, in the user name field, enter guest.
The guest user name does not require a password. To restrict access to the USB
drive, you can specify that only the admin user can access it. See Control Access to
the USB Drive on page 73.
The files and folders of the USB drive that your account can access displays. For
example, you might see share/partition1/directory1.
Dynamic DNS
Internet service providers (ISPs) assign numbers called IP addresses to identify each
Internet account. Most ISPs use dynamically assigned IP addresses. This means that the IP
address can change at any time. You can use the IP address to access your network
remotely, but most people don’t know what their IP addresses are or when this number
changes.
To make it easier to connect, you can get a free account with a Dynamic DNS service that
lets you use a domain name to access your home network. To use this account, you must set
up the router to use Dynamic DNS. Then the router notifies the Dynamic DNS service
provider whenever its IP address changes. When you access your Dynamic DNS account,
the service finds the current IP address of your home network and automatically connects
you.
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), the Dynamic
DNS service does not work because private addresses are not routed on the Internet.
Your Personal FTP Server
With your customized free URL, you can use FTP to access your network when you aren’t
home through Dynamic DNS. To set up your FTP server, you must register for a free
Access the Router’s USB Drive Through the Internet
84
Nighthawk AC1750 Smart WiFi Router
NETGEAR Dynamic DNS (DDNS) service account and specify the account settings. See Set
Up a New Dynamic DNS Account on page 85.
FTP Directory: FTP://‘custom name’.mynetgear.com
FTP Directory: FTP://‘custom name’.mynetgear.com
FTP Directory:
FTP://‘custom name’.mynetgear.com
FTP
Director
y: FTP://‘cu
stom
name’.m
ynetgea
r.com
FTP
Directory
: FTP://
‘custom
name’.my
netgear.c
om
Figure 10. You can access your network through the Internet when you’re not home
Note: The router supports only basic DDNS, and the login and password
might not be secure. You can use DDNS with a VPN tunnel for a
secure connection. For more information, see Chapter 7, Access the
Router’s USB Drive Through the Internet.
Set Up a New Dynamic DNS Account

To set up Dynamic DNS and register for a free NETGEAR account:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Access the Router’s USB Drive Through the Internet
85
Nighthawk AC1750 Smart WiFi Router
4. Select ADVANCED > Advanced Settings > Dynamic DNS.
5. Select the Use a Dynamic DNS Service check box.
6. In the Service Provider list, select NETGEAR.
7. Select the No radio button.
8. In the Host Name field, type the name that you want to use for your URL.
The host name is sometimes called the domain name. Your free URL includes the host
name that you specify, and ends with mynetgear.com. For example, specify
MyName.mynetgear.com.
9. In the Email field, type the email address for your account.
10. In the Password (6-32 characters) field, type the password for your account.
11. Click the Register button.
12. Follow the onscreen instructions to register for your NETGEAR Dynamic DNS service.
Specify a DNS Account That You Already Use
If you already set up a Dynamic DNS account with NETGEAR no-ip, www.no-ip.com, or
www.DynDNS.org, you can set up the router to use your account.

To set up Dynamic DNS if you already set up an account:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
Access the Router’s USB Drive Through the Internet
86
Nighthawk AC1750 Smart WiFi Router
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Settings > Dynamic DNS.
5. Select the Use a Dynamic DNS Service check box.
6. In the Service Provider list, select one of the following:
• NETGEAR
•
www.no-ip.com
•
www.DynDNS.org
7. Select the Yes radio button.
The screen adjusts and displays the Show Status, Cancel, and Apply buttons.
8. In the Host Name field, type the host name (sometimes called the domain name) for your
account.
9. For a www.no-ip or www.DynDNS account, in the User Name field, enter the user name for
your account.
10. For a NETGEAR account at www.no-ip, in the Email field, type the email address for your
account.
11. In the Password (6-32 characters) field, type the password for your DDNS account.
12. Click the Apply button.
Your changes are saved.
13. To verify that your Dynamic DNS service is enabled in the router, click the Show Status
button.
A message displays the Dynamic DNS status.
Access the Router’s USB Drive Through the Internet
87
Nighthawk AC1750 Smart WiFi Router
Change the Dynamic DNS Settings

To change your settings:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > Advanced Settings > Dynamic DNS.
The Dynamic DNS screen displays.
5. Change your DDNS account settings as necessary.
6. Click the Apply button.
Your changes are saved.
Set Up Your Personal FTP Server

To set up your personal account and use FTP:
1. Get your free NETGEAR Dynamic DNS domain name.
See Your Personal FTP Server on page 84.
2. Make sure that your Internet connection is working.
Your router must use a direct Internet connection. It cannot connect to a different router to
access the Internet.
3. Connect a USB hard disk drive to a USB port on the router.
4. Set up FTP access in the router.
See Set Up FTP Access Through the Internet on page 82.
5. On a remote computer with Internet access, you can use FTP to access your router using
ftp://yourname.mynetgear.com.
Access the Router’s USB Drive Through the Internet
88
8.
Use the Router as a Media Server
The router comes set up to work as a ReadyDLNA media server. You can set up the router to
play music from iTunes Server and media from TiVo.
This chapter contains the following sections:
•
Specify ReadyDLNA Media Server Settings
•
Play Music from a USB Drive with iTunes Server
•
Play Media from a USB Drive on TiVo
89
Nighthawk AC1750 Smart WiFi Router
Specify ReadyDLNA Media Server Settings
By default, the router acts as a ReadyDLNA media server, which lets you view movies and
photos on DLNA/UPnP AV-compliant media players, such as Xbox360, Playstation, and
NETGEAR media players.

To specify media server settings:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > USB Storage > Media Server.
The Media Server (Settings) screen displays.
5. Specify the settings:
• Enable Media Server. Select this check box to enable this device to act as a media
server.
•
Enable TiVo support. Select this check box if you want to play ReadyNAS media on
your TiVo device. See the Play Media from a USB Drive on TiVo on page 92.
•
Media Server Device Name. Specify the name of the media server.
6. Click the Apply button.
Your changes are saved.
Play Music from a USB Drive with iTunes Server
iTunes Server lets you play music with your Windows or Mac iTunes app from a USB drive
that is connected to the router USB port. You can also use the Apple Remote app from an
Use the Router as a Media Server
90
Nighthawk AC1750 Smart WiFi Router
iPhone or iPad to play music on any AirPlay devices, such as Apple TV or AirPlay-supported
receivers.
Figure 11. Play music on a USB drive with iTunes
Supported music file formats are MP3, AAC, and FLAC. The maximum number of music files
supported is 10,000.

To specify iTunes server settings:
1. On your iPhone or iPad, find and connect to the WiFi network.
2. Launch the Remote app.
3. Click the Add an iTunes Library button.
A passcode displays.
4. Specify the passcode in the router:
a. Launch an Internet browser from a computer or wireless device that is connected to
the network.
b. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
c. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
Use the Router as a Media Server
91
Nighthawk AC1750 Smart WiFi Router
d. Select ADVANCED > USB Storage > Media Server.
e. Make sure that the Enable iTunes Media Server (Music Only) check box is
selected.
f.
Enter the passcode.
g. Click the Allow Control button.
h. Click the Apply button.
Your changes are saved.
On your iPhone or iPad, the ReadySHARE music library displays in the Remote app.
You can play this music to AirPlay devices.
Play Media from a USB Drive on TiVo
You can set up your TiVo to access media files stored on a USB device that is connected to
your router. The TiVo must be on the same network as the router. This feature supports the
following file formats:

•
Video. See and play mpeg1, and mpeg2 files.
•
Music. See and play MP3 files.
•
Pictures. View images in .jpg format.
To set up the router to work with TiVo:
1. Launch an Internet browser from a computer or wireless device that is connected to the
network.
2. Type http://www.routerlogin.net or http://www.routerlogin.com.
A login screen displays.
3. Enter the router user name and password.
The user name is admin. The default password is password. The user name and
password are case-sensitive.
The BASIC Home screen displays.
4. Select ADVANCED > USB Storage > Media Server.
The Media Server Settings screen displays.
Use the Router as a Media Server
92
Nighthawk AC1750 Smart WiFi Router
5. Make sure that the Enable TiVo support check box is selected.
If you changed the setting, click the Apply button.
Your settings are saved.

To play videos:
1. On the TiVo, select TiVo Central > My Shows.
2. Go to the bottom of the list tand select the R6700.

To play music or view photos:
1. On the TiVo, select TiVo Central > Music, Photos, & Showcases.
Use the Router as a Media Server
93
Nighthawk AC1750 Smart WiFi Router
2. Select an item to play or watch.

To copy TiVo files to a computer:
Use the TiVo Desktop accessory, available at
https://www3.tivo.com/store/accessories-software.do.
Use the Router as a Media Server
94
9.
Share a USB Printer
The ReadySHARE Printer utility lets you share a USB printer that is connected to the USB port
on your router. You can share this USB printer among the Windows and Mac computers on your
network.
This chapter contains the following sections:
•
Install the Printer Driver and Cable the Printer
•
Download the ReadySHARE Printer Utility
•
Install the ReadySHARE Printer Utility
•
Use the Shared Printer
•
View or Change the Status of a Printer
•
Use the Scan Feature of a Multifunction USB Printer
•
Change NETGEAR USB Control Center Settings
95
Nighthawk AC1750 Smart WiFi Router
Install the Printer Driver and Cable the Printer
Some USB printer manufacturers (for example, HP and Lexmark printers) request that you
do not connect the USB cable until the installation software prompts you to do so.

To install the driver and cable the printer:
1. On each computer on your network that shares the USB printer, install the driver
software for the USB printer.
If you cannot find the printer driver, contact the printer manufacturer.
2. Use a USB printer cable to connect the USB printer to the router USB port.
USB port
Download the ReadySHARE Printer Utility
The utility works on Windows and Mac computers.

To download the utility:
1. Visit www.netgear.com/readyshare.
Share a USB Printer
96
Nighthawk AC1750 Smart WiFi Router
2. In the ReadySHARE Printer pane, click the PC Utility or Mac Utility link.
3. Follow the onscreen instructions to download the file.
Install the ReadySHARE Printer Utility
You must install the ReadySHARE Printer utility on each computer that will share the printer.
After you install it, the utility displays as NETGEAR USB Control Center on your computer.

To install the utility:
1. Double-click the ReadySHARE Printer utility setup file that you downloaded.
The InstallShield wizard displays.
2. Follow the wizard instructions to install NETGEAR USB Control Center.
After the InstallShield Wizard completes the installation, the NETGEAR USB Control
Center prompts you to select a language:
3. Select a language from the list and click the OK button.
Share a USB Printer
97
Nighthawk AC1750 Smart WiFi Router
The NETGEAR USB Control Center displays the main screen.
Some firewall software, such as Comodo, blocks NETGEAR USB Control Center from
accessing the USB printer. If you do not see the USB printer displayed in the screen, you
can disable the firewall temporarily to allow the utility to work.
4. Select the printer and click the Connect button.
The printer status changes to Manually connected by Mycomputer. Now, only your
computer can use the printer.
5. Click the Disconnect button.
The status changes to Available. Now all computers on the network can use the printer.
6. To exit the utility, select System > Exit.
Use the Shared Printer
For each computer, after you click the Connect and Disconnect buttons once, the utility
automatically manages the printing queue and handling. By default, the utility starts
automatically whenever you log on to Windows and runs in the background.

To manually connect and print:
1. Click the NETGEAR USB Control Center icon
The main screen displays.
2. Click the Connect button.
The printer status changes to Manually connected by Mycomputer. Now, only the
computer you are using can use this printer.
3. Use the print feature in your application to print your document.
4. To release the printer so that all computers on the network can use it, click the Disconnect
button.
Share a USB Printer
98
Nighthawk AC1750 Smart WiFi Router

To print and release the printer to any computer on the network:
1. To print your document, use the print feature in your application.
The NETGEAR USB Control Center automatically connects your computer to the USB
printer and prints the document. If another computer is already connected to the printer,
your print job goes into a queue to wait to be printed.
2. If your document does not print, use the NETGEAR USB Control Center to check the status.
See View or Change the Status of a Printer on page 99.
View or Change the Status of a Printer

To view or change the status:
1. Click the NETGEAR USB Control Center icon
The main screen displays.
The Status column shows the status for each device:
•
Available. No print jobs are in process. You can use the USB printer from any
computer in the network.
•
Connected. Your computer is connected to the printer and will be released when
your print job is done.
•
Manually Connected by. Only the connected computer can use the printer.
•
Waiting to Connect. Your computer is not connected to the shared printer yet.
2. To print from your computer when the status shows Manually connected by another
computer, click the Disconnect button.
The printer is released from the connection and the status changes to Available.
3. To print from your computer when the status shows Waiting to Connect:
a. Click the Connect button.
The printer status changes to Manually connected by Mycomputer. Now, only your
computer can use the printer.
b. To allow the printer to be shared, click the Disconnect button.
The printer is released from the connection and the status changes to Available.
Share a USB Printer
99
Nighthawk AC1750 Smart WiFi Router
Use the Scan Feature of a Multifunction USB Printer
If your USB printer supports scanning, you can also use the USB printer for scanning. For
example, the USB printer displayed in the Windows Printers and Faxes window is ready for
print jobs.

To use the scan feature of a multifunction USB printer:
1. Launch the NETGEAR USB Control Center.
2. Make sure that the printer status shows as Available.
3. Click the Network Scanner button.
The scanner screen displays so that you can use the USB printer for scanning.
Share a USB Printer
100

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : NETGEAR
Create Date                     : 2015:05:12 22:16:11+08:00
Modify Date                     : 2015:05:12 22:18:22+08:00
Subject                         : NETGEAR Nighthawk AC1750 Smart WiFi Router Model R6700 User Manual
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2015:05:12 22:18:22+08:00
Creator Tool                    : FrameMaker 10.0.2
Format                          : application/pdf
Title                           : NETGEAR Nighthawk AC1750 Smart WiFi Router Model R6700 User Manual
Description                     : NETGEAR Nighthawk AC1750 Smart WiFi Router Model R6700 User Manual
Creator                         : NETGEAR
Document ID                     : uuid:c79fb263-666e-429c-8495-e9eeeb302def
Instance ID                     : uuid:599903a0-fa6b-4f64-8a1f-69e8c71dca25
Producer                        : Acrobat Distiller 10.1.10 (Windows)
Page Count                      : 100

EXIF Metadata provided by EXIF.tools