Netronix W403 Wireless 802.11n PCI Card User Manual 61NB W40300 217 for EMI
Netronix Inc Wireless 802.11n PCI Card 61NB W40300 217 for EMI
Netronix >
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 855773 |
| Application ID | 1fkZtptuhGA0Syj4X6B3+Q== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 82.55kB (1031885 bits) |
| Date Submitted | 2007-10-17 00:00:00 |
| Date Available | 2007-10-17 00:00:00 |
| Creation Date | 2007-10-11 14:58:13 |
| Producing Software | AFPL Ghostscript 8.54 |
| Document Lastmod | 2007-10-11 18:10:49 |
| Document Title | 61NB-W40300+217 for EMI |
| Document Creator | PDFCreator Version 0.9.2 |
| Document Author: | KELLY |
User’s Guide Wireless 802.11n PCI Card W403 FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b/g or 802.11n operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN 60950-1: 2001 Safety of Information Technology Equipment EN 50392: 2004 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz) EN 300 328 V1.6.1 (2004-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-17 V1.2.1 (2002-08) and EN 301 489-1 V1.5.1 (2004-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. 0560 Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiāijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, Ŝe [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Nome do fabricante] declara que este [tipo de equipamento] está [Portuguese] conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. TABLE OF CONTENTS OVERVIEW .................................................... ....................................................6 .................... 6 UNPACKING INFORMATION ................................................................................... 6 INTRODUCTION TO THE IEEE 802.11N WIRELESS PCI/ MINI PCI ADAPTER .................................................................................................................... 6 KEY FEATURES ........................................................................................................ 7 INSTALLATION GUIDE ............................7 ............................ 7 SOFTWARE INSTALLATION ................................................................................... 7 MANAGEMENT GUIDE .......................... 10 MAKING A BASIC NETWORK CONNECTION .................................................. 10 Select a configuration tool ........................................................................................ 10 To connect with Microsoft Zero Configuration tool.................................................... 10 To connect with 802.11n Wireless LAN Utility .......................................................... 12 INTRODUCTION TO THE 802.11N WIRELESS LAN UTILITY..................... 13 Interfaces.................................................................................................................. 13 Information................................................................................................................ 14 Profile ....................................................................................................................... 15 Network .................................................................................................................... 19 Advanced.................................................................................................................. 20 Statistics ................................................................................................................... 21 WMM ........................................................................................................................ 22 WPS ......................................................................................................................... 22 APPENDIX ................................................... ................................................... 24 INTRODUCTION TO THE CONFIGURATION UTILITY FOR VISTA USERS .. 24 Profile ....................................................................................................................... 24 Link Status................................................................................................................ 26 Site Survey ............................................................................................................... 27 Statistics ................................................................................................................... 28 AP MODE MANAGEMENT GUIDE ....................................................................... 32 Security Settings....................................................................................................... 33 Access Control ......................................................................................................... 34 MAC Table................................................................................................................ 35 Event Log ................................................................................................................. 35 Statistics ................................................................................................................... 36 PRODUCT SPECIFICATION SPECIFICATION ................. 37 Overview Thank you for purchasing this product. Read this chapter to know about your IEEE 802.11n Wireless PCI/ Mini PCI Adapter. Unpacking Information Before getting started, please verify that your package includes the following items: 1. 2. IEEE 802.11n Wireless PCI/ Mini PCI Adapter. One Utility/ Manual CD. Introduction to the IEEE 802.11n Wireless PCI/ Mini PCI Adapter The IEEE 802.11n Wireless PCI/ Mini PCI adapter provides users to launch IEEE 802.11n wireless network at 300 Mbps in the 2.4GHz band, which is also compatible with IEEE 802.11b/g wireless devices at 11/54 Mbps. You can configure this adapter with Ad-hoc mode to connect to other 2.4GHz wireless computers, or with Infrastructure mode to connect to a wireless AP or router for accessing to Internet. This adapter includes a convenient Utility for scanning available networks and saving preferred networks that users usually connected with. Security encryption can also be configured by this Utility. Key Features Complies with standards IEEE 802.11n/b/g wireless Supports driver for Windows 2000, XP 32/64, Vista 32/64, Linux (2.4.x/2.6.x), and Mac (10.3.x/10.4.x). 2.4GHz Frequency band, MIMO 2T3R Supports QoS: WMM, WMM-PS Complies with PCI 2.3 or Mini PCI type III Supports wireless data 64/128-bit WEP, WPA, WPA2 High Speed transfer data rate up to 300 Mbps Supports Multiple BSSID Supports auto-installation. encryption with Installation Guide Software Installation Note: For Linux or Mac driver installation guide, please refer to the instruction in /Driver/Linux or /Driver/Mac in the CD-Rom. The following driver installation guide uses Windows XP as the presumed operation system. The procedures and screens in Windows 2000 and Vista are familiar with Windows XP. 1. Insert this product to your computer. The system finds the newly installed device automatically. Click Cancel to close this window. 2. Insert the CD-Rom that came with this product to your CD-Rom drive. The menu window pops up automatically. Please click the Driver button of this product. Note: If the CD-Rom fails to auto-run, please click on My Computer> your CD-Rom drive> (folder of this product)> Driver then double-click the Setup icon to start this menu. 3. Select if you are going to configure your wireless network with this device or with Microsoft Zero Configuration tool. Note: This can be changed after installing this software. 4. Select to optimize this adapter in WiFi mode or performance mode. Note: The performance mode is only available while connecting to a TX Burst supported AP. Users that uses the AP without TX Burst please select WiFi mode (standard mode). 5. Click the Install button to start installing. 6. Click the Finish button to complete installation. Management Guide Read this chapter to understand the management interface of the device and how to manage the device. Making a Basic Network Connection Select a configuration tool In the following instruction for making a network connection, we use the Utility we provide to configure your wireless network settings. Note: You could use either the software we provide or Microsoft Zero Configuration tool to configure this adapter. To switch between the two configuration tools, please right click on the ….. icon on system tray to select. To connect with Microsoft Zero Configuration tool After specifying the Microsoft Zero Configuration tool to configure your wireless network, right click on the icon on system tray. Select View Available Wireless Networks to specify your wireless network. 10 The tool shows the available wireless networks. Select your demanding network to connect with. To connect to a wireless network with more security settings, please click Change advanced settings to be compatible with your wireless network security settings. 11 To connect with 802.11n Wireless LAN Utility We provide this Utility for users to connect to a wireless network easily. It provides more information and configuration for this adapter. As default, the Utility is started automatically upon starting your computer and connects to a connectable wireless network with best signal strength. Right click on the icon and select Launch Config utilities if the Utility does not start. Please refer to the following chapters to get information regarding to the functions of this Utility. 12 Introduction to the 802.11n Wireless LAN Utility Note: The Utility in Windows Vista, Linux and Mac are different from the following. For instructions on using the Utility included in Windows Vista please refer to the instruction in Appendix. For instructions on using the Utility included in Linux please refer to the instruction in /Driver/Linux/readme.txt in the CD-Rom. For instructions on using the Utility included in Mac please refer to the instruction in /Driver/Mac/readme.txt in the CD-Rom. Interfaces This Utility is basically consisted of three parts: 1. Functional buttons: on top of the window. You can click each button to access each configuration window. Note: Click Click on the top right window to enable/disable wireless connection status. to show the wireless information. 2. Configuration column: Center of the Utility window. Make your changes for each function in this part. 3. Status information: bottom of the utility window. Shows the connection status and system information. 13 Information Items Status Extra Info Channel Authentication Encryption Network Type IP Address Sub Mask Default Gateway Link Speed Throughput Link Quality Signal Strength 1 Signal Strength 2 Signal Strength 3 Noise Strength HT Information Shows the connecting status. Also shows the SSID while connecting to a valid network. Display link status in use. Display current channel in use. Authentication mode in use. Encryption type in use. Network type in use. IP address of current connection. Subnet mask of current connection. Default gateway of current connection. Show current transmit rate and receive rate. Display transmit and receive throughput in Mbps. Display connection quality based on signal strength and TX/RX packet error rate. Receive signal strength 1, user can choose to display as percentage or dBm format. Receive signal strength 2, user can choose to display as percentage or dBm format. Receive signal strength 3, user can choose to display as percentage or dBm format. Display noise signal strength. Display current HT status in use, containing BW, GI, MCS, SNR0, and SNR1 value. 14 Profile This profile page allows users to save different wireless settings, which helps users to get access to wireless networks at home, office or other wireless network environments quickly. To add a new profile: 1. Click the Add button. The add profile window pops up. Note: you could also add a new profile quickly by selecting an available network in the Network function then click the Add to Profile button. 2. Fill in information for this profile in the system config section: Items Profile Name SSID Power Save Mode Network Type RTS Threshold Fragment Threshold Information Choose a name for this profile, or use default name defined by system. Fill in the intended SSID name or use the drop list to select from available Aps. Choose from CAM (Constantly Awake Mode) or PSM (Power Saving Mode). There are two types, infrastructure and 802.11 Ad-hoc modes. Under Ad-hoc mode, you could also choose the preamble type; the available preamble type includes auto and long. In addition to that, the channel field will be available for setup in Ad-hoc mode. For adjusting the RTS threshold number by sliding the bar or key in the value directly. The default value is 2347. Adjust the Fragment threshold number by sliding the bar or key in the value directly. The default value is 2346. 15 3. Select an encryption type and fill in the corresponding wireless network information: Items Authentication Type Encryption Type Information There are 7 types of authentication modes supported by Utility including open, Shared, LEAP, WPA and WPA-PSK, WPA2 and WPA2-PSK. For open and shared authentication mode, the selection of encryption type are None and WEP. For WPA, WPA2, WPA-PSK and WPA2-PSK authentication mode, the encryption type supports both TKIP and AES. 802.1x Use 802.1x to make WPA and WPA2 certification. This functions only works when connecting to a WPA and WPA2 supported device. WPA Pre-shared This is the shared secret between AP and STA. For WPA-PSK and Key WPA2-PSK authentication mode, this field must be filled with character longer than 8 and less than 32 length. WEP Key Only valid when using WEP encryption algorithm. The key must matched AP's key. 4. Specify the 802.1x information if you are using the 802.1X certification method. Users that do not use this function or connecting to an open-wireless network please skip this part. Items EAP method Tunnel Authentication Session Resumption Information To select an EAP method. Select a Tunnel authentication mode. Select to enable this function or unmark it to disable. 16 ID \ PASSWORD Items Authentication ID / Password Tunnel ID / Password Information The identity, password and domain name for server. Only "EAP-FAST" and "LEAP" authentication can be key in domain name. Blank space can be key in domain name. Identity and Password for server. Client Certification Items Use Client certificate Information Client certificate for server authentication. 17 EAP Fast Items Information Allow unauthenticated provision mode Mark to enable unauthenticated provision mode. Use protected authentication Mark to use protected authentication credential. credential Server Certification Items Use Certificate chain Allow intimidate certificates Server name Information Mark the checkbox to enable using certification chain. Mark to allow intimidates certification. Enter an authentication sever root. 18 Network This network lists the available wireless networks. The Utility connects to a wireless network with best signal strength automatically. You can change the connecting network by clicking on the network name and click the Connect button. To see detail information of each network, please double click on each item to pop up the information window. Items SSID, Channel and Signal buttons Show dBm Rescan Connect Add to Profile Information Click each button to sort the listing networks by SSID, channel and Signal strength. Mark the checkbox to show the signal strength in dBm. To rescan available wireless networks. Click this button to connect to a designated network. Click this button to add a network to profile after selecting a network. 19 Advanced This page provides advanced configurations to this adapter. Please refer to the following chart for definitions of each item. Items Wireless mode Enable TX Burst Enable TCP Window Size Information Click the drop list to select a wireless mode. Select to enable connecting to a TX Burst supported device. Mark the checkbox to enable TCP window size, which help enhance throughput. Fast Roaming at __ dBm Mark the checkbox to enable fast roaming. Specify the transmit power for fast roaming. Show Authentication Mark the checkbox to show “Authentication Status Dialog” while Status Dialog connecting to an AP with authentication. Authentication Status Dialog displays the process about 802.1x authentication. Enable CCX (Cisco Select to enable CCX. This function can only be applied when Compatible extensions) connecting to a Cisco compatible device. 20 Statistics Statistics page displays the detail counter information based on 802.11 MIB counters. This page translates the MIB counters into a format easier for user to understand. Items Information Use Client certificate Client certificate for server authentication. Frames Transmitted Successfully Frames successfully sent. Frames Retransmitted Successfully Successfully retransmitted frames numbers. Frames Fail To Receive ACK After Frames failed transmit after hitting retry limit. All Retries RTS Frames Successfully Receive Successfully receive CTS after sending RTS frame. CTS RTS Frames Fail To Receive CTS Failed to receive CTS after sending RTS. Restart Counter Reset counters to zero. Items Use Client certificate Frames Received Successfully Frames Received With CRC Error Frames Dropped Due To Out-of-Resource Duplicate Frames Received 21 Information Client certificate for server authentication. Frames received successfully. Frames received with CRC error. Frames dropped due to resource issue. Duplicate received frames. WMM This page allows users to activate the WMM function for this device. Please note that this function only works while connecting to a WMM compatible device. Items Use Client certificate WMM Enable WMM - Power Save Enable Direct Link Setup Enable Information Client certificate for server authentication. Enable Wi-Fi Multi-Media. Enable WMM Power Save. Please enable WMM before configuring this function. Enable DLS (Direct Link Setup). Please enable WMM before configuring this function. WPS WPS Configuration: The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security setup and management of Wi-Fi networks. This adapter supports the configuration setup using PIN configuration method or PBC configuration method through an internal or external Registrar. 22 Items Use Client certificate WPS AP List Rescan Information PIN Code Config Mode Table of Credentials Detail Connect Rotate Disconnect Delete PIN PBC WPS associate IE WPS probe IE Progress Bar Status Bar Information Client certificate for server authentication. Display the information of surrounding APs with WPS IE from last scan result. List information includes SSID, BSSID, Channel, ID (Device Password ID), and Security-Enabled. Click to rescan the wireless networks. Display the information about WPS IE on the selected network. List information include Authentication Type, Encryption Type, Config Methods, Device Password ID, Selected Registrar, State, Version, AP Setup Locked, UUID-E and RF Bands. 8-digit numbers. It is required to enter PIN Code into Registrar using PIN method. Each Network card has only one PIN Code of Enrollee. Enrollee or an external Registrar. Display all of credentials got from the Registrar. List information includes SSID, MAC Address, Authentication and Encryption Type. If STA Enrollee, credentials are created as soon as each WPS success. If STA Registrar, Utility creates a new credential with WPA2-PSK/AES/64Hex-Key and doesn't change until next switching to STA Registrar. Information about Security and Key in the credential. Command to connect to the selected network inside credentials. Command to connect to the next network inside credentials. Stop WPS action and disconnect this active link. And then select the last profile at the Profile Page of Utility if exist. If there is an empty profile page, the driver will select any non-security AP. Delete an existing credential. And then select the next credential if exist. If there is an empty credential, the driver will select any non-security AP. Start to add to Registrar using PIN configuration method. Start to add to AP using PBC configuration method. Send the association request with WPS IE during WPS setup. It is optional for STA. Send the probe request with WPS IE during WPS setup. It is optional for STA. Display rate of progress from Start to Connected status. Display currently WPS Status. Note: When you click PIN or PBC, please don't do any rescan within two-minute connection. If you want to abort this setup within the interval, restart PIN/PBC or click Disconnect to stop WPS action. 23 Appendix Introduction to the configuration utility for Vista Users This utility helps Vista users to configure the wireless network. Please refer to the following sections for introduction. Profile This profile page allows users to save different wireless settings, which helps users to get access to wireless networks at home, office or other wireless network environment quickly. 24 To add a new profile: 1. Click the Add button. The add profile window pops up. Note: you could also add a new profile quickly by selecting an available network in the Site Survey function then click the Add to Profile button. 2. Fill in the information of this wireless network and its relative security settings. Please note that the information should be corresponding to the wireless network you are connecting to. Items Deleting profile Editing profile Information Click the Delete button to delete the selected profile. Click the Edit button to pop up the profile-setting page for users to edit the existing profile. Activating profile Click the Activate button to activate the selected profile. 25 Link Status This Link status shows the information about the connecting. Please refer to the following chart for definition. Items Status Extra Info Link Speed Throughput Link Quality Signal Strength Noise Level Information Display current connection status. Display link status and current channel in use. Display current transmitting and receiving rates. Display transmitting and receiving throughputs. Display connecting quality based on signal strength and TX/RX packet error rate. Display receiving signal strength either in percentage or dBm format. Display noise signal strength. 26 Site Survey This page shows the available wireless networks within the coverage of this network adapter. You could check the status of wireless network around your computer or add a network into your profile. Items SSID BSSID Phy Type Signal Channel Encryption Authentication Network Type Rescan Add to profile Information Name of the network. AP MAC address or random numbers generated for IBSS. Phy Type of the network. Signal strength of the network. The channel in use. Encryption algorithm. The supported algorithms are WEP, TKIP, AES, and Not Use. Authentication mode. The supported modes are Unknown, WPA-PSK, WPA2-PSK, WPA and WPA2. Infrastructure or Ad-Hoc. Click the rescan button to perform re-scanning. Select a network then click the Add to Profile button to bring up the profile-setting to add a wireless network profile. 27 Statistics This page provides the statistics about the connection of this adapter. Items Frames Transmitted Successfully Frames Transmitted Successfully After Retry Frames Fail To Receive ACK After All Retries RTS Frames Successfully Receive CTS RTS Frames Fail To Receive CTS Frames Received Successfully Frames Received With CRC Error Frames Dropped Due To Out-of-Resource Duplicate Frames Received Information Frames sent successfully. Frames sent successfully with retry. Frames transmitted failed after hitting the retrying limit. CTS frames received successfully after sending RTS frames. The missing CTS frames after sending RTS frames. Frames received successfully. Frames received with CRC error. Frames dropped due to insufficient resource. Duplicate frames received. 28 WPS Configuration This page provides users to connect this adapter to a WPS (Wi-Fi Protected Setup) AP. Those available WPS supported AP are listed on the upper column. Select the AP that you want to connect to and click the Connect button to activate. WPS Associate IE: If the "WPS Associate IE" option is checked, station sends a association request with WPS IE during WPS setup. WPS Probe IE: If the "WPS Probe IE" option is checked, station probes a request with WPS IE during WPS setup. Re-scanning: Click the Rescan button to perform the re-scanning. WPS AP Information: Click the WPS information button to bring up the WPS capable AP information dialog window. The window shows the information including: Authentication Type: There are three types of supported authentication modes including Open, Shared, WPA-PSK and WPA modes. Encryption Type: For Open and Shared authentication modes, the available encryption types are None and WEP. For WPA, WPA2, WPA-PSK and WPA2-PSK authentication modes, the available encryption types are TKIP and AES. 29 Config Methods: This attribute contains the config methods supported and enabled by the selected Registrar. Device Password ID: Device Password ID indicates the method or identifies the specific password that the selected Registrar intends to use. Selected Registrar: Selected Registrar indicates if the user has recently activated a Registrar to add an Enrollee. State: This attribute is used to indicate the current configuration state. This attribute is either "Un-configured" or "Configured". Version: This attribute is the specified WPS version. AP Setup Locked: AP Setup Locked indicates if AP has entered a setup locked state. UUID-E: UUID-E is universally unique identifier (UUID) generated by the Enrollee. RF Bands: RF Bands indicate the available RF bands. Configure WPS profiles: The user can configure WPS profiles with either PIN method or PBC method. PIN Method: Step 1: The Registrar enters the pin code generated by station. Step 2: Push the PIN button. PBC Method: Push the PBC button within 2 second while the Registrar pushes the button. 30 Manage WPS profiles: The received WPS profiles are listed in the lower frame, and the listed WPS profile attributes are SSID, MAC address, authentication type, and encryption type. WPS profile detail information: Selecting a profile then pushing the Detail button brings up the WPS profile. This profile shows information including: Connect with WPS profile: Clicking the Connect button will connect to AP with the selected WPS profile. Rotate WPS profiles: If there are more than two WPS profiles, clicking the Rotate button will rotate to next profile and connect to AP with this profile. If the connection can't be established successfully, station will perform the WPS profile rotation repeatedly. Disconnect from WPS AP: Click the Disconnect button to stop the WPS connection. Delete WPS profile: Click the Delete button to delete the selected WPS profile. 31 AP mode management guide This adapter can be configured as AP mode. To function this adapter as an AP, please right click the icon on system tray and select Switch to AP mode. Please refer to the following introduction to information about this AP-mode utility. Note: In windows XP, it provides WPA support at hotfix Q815485 However; you have to make sure that hotfix Q815485 (require XP SP1 installed) has been installed in your system before you can start using WPA features. You can check the installation of hotfix in add/remove software page under control panel. 32 Security Settings This page pops up after clicking the Security Settings button. Please follow the instructions below: Items 1. Authentication Type 2. Encryption Type 3. WPA Pre-shared Key 4. Group Rekey Interval 5. WEP Key Information Select to be open or WPA-PSK system. Select an encryption type from the drop list. A shared string between AP and STA. For WPA-PSK authentication mode, this field must be filled with character longer than 8 and less than 32 length. (PCI only) Only valid when using WPA-PSK encryption algorithm. The key will change compliance with seconds or beacon that user set. (PCI device only) Only valid when using WEP encryption algorithm. The key must match the key on AP. There are several formats to enter the keys. a. Hexadecimal (40bits): 10 Hex characters. b. Hexadecimal (128bits): 32Hex characters. c. ASCII (40bits): 5 ASCII characters. d. ASCII (128bits): 13 ASCII characters. 33 Access Control This function filters users to use this device by designating MAC address. Please refer to the following chart for introduction. Items 1. Access Policy 2. 3. 4. 5. 6. MAC Address Access List Delete Remove All Apply Information Choose a method to process access control from the drop list to determine the MAC addresses that you designated are allowed to access the AP or not. Add allowed (or denied) MAC addresses to the MAC address list. Display all Mac Addresses that you designated. Delete Mac addresses that you selected. Remove all Mac address in [Access List]. Apply changes. 34 MAC Table This page displays the station detail information of current connection. Items MAC Address AID Power Saving Mode Information The station MAC address of current connection. Raise value by current connection. Check if the connected station supports power saving. Event Log Record Soft AP all event time and message. Items Event Time (yy/mm/dd-hh:mm:ss) Message 35 Information Record event time. All event messages. Statistics Statistics page displays the detail counter information based on 802.11 MIB counters. 1. Transmit Statistics Items Frames Transmitted Successfully Frames Fail To Receive ACK After All Retries RTS Frames Successfully Receive CTS RTS Frames Fail To Receive CTS Frames Retransmitted Successfully Information Frames that successfully sent. Frames that failed to transmit after hitting retry limit. Counts of CTS that successfully received after sending RTS frame. Counts of CTS that fail to be received after sending RTS frame. Successfully retransmitted frames numbers. 2.Recieve Statistics Items Frames Received Successfully Frames Received With CRC Error Frames Dropped Due To Out-of-Resource Duplicate Frames Received Information Frames received successfully. Frames received with CRC error. Frames dropped due to resource issue. Duplicate received frames. 3. Reset Counters: Reset counters to zero. 36 Product Specification Standard IEEE 802.11n draft 2.0, IEEE 802.11b, IEEE 802.11g Interface PCI 2.3 or Mini PCI type III Antenna Antenna gain: 2dB Antenna type: Dipole Antenna connector type: Reverse SMA LED indication Link/Act (Green) Security 64/128-bit WEP, WPA, WPA2 Receiver Sensitivity 802.11b-88dBm, 802.11g-75dBm, 802.11n-65dBm Channel USA 11, Europe 13 Transmit Power 802.11b 18dBm, 802.11g 15dBm, 802.11n 20MHz and 802.11n 40MHz 18dBm Network Data Rate 802.11b: 1,2,5.5 and 11Mbps 802.11g: 6,9,12,18,24,36,48 and 54Mbps 802.11n: up to 300Mbps Range Coverage Indoor 35~100 meters Outdoor 100~300 meters Operating Temperature 0- 40℃ (32 – 104℃) Operating Humidity 10% ~ 90% (non-condensing) Emission FCC Class B, CE FCC Part 15.247 for US (2.142~2.462 MHz) ETS 300 328 for Europe (2.400~2483.5 MHz) DGT LP0002 for Taiwan (2.412~2.462MHz) 37 61NB-W40300+217
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Print high-res XMP Toolkit : 3.1-702 About : f5fd465b-7a22-11dc-0000-88ffa0c0a373 Producer : AFPL Ghostscript 8.54 Modify Date : 2007:10:11 18:10:49+08:00 Create Date : 2007:10:11 14:58:13+08:00 Creator Tool : PDFCreator Version 0.9.2 Metadata Date : 2007:10:11 18:10:49+08:00 Document ID : f5fd465b-7a22-11dc-0000-88ffa0c0a373 Instance ID : uuid:ac4e348a-fdf1-4850-829b-b3e5684efe23 Format : application/pdf Title : 61NB-W40300+217 for EMI Creator : KELLY Page Count : 38 Author : KELLYEXIF Metadata provided by EXIF.tools