Users Manual
гг
Various power switch
: : :
The remote control buttons have different functions depending on the active mode. To change the mode, press the desired
button on the right side of the panel (Input/Output mode select buttons).
To check which mode is selected, just press any button other than the Input/Output select buttons and the active mode will light
up.
About R2-D2 sound (R2-D2 sounds are emitted by a special internal speaker inside R2-D2): When
the power is ON, etc., R2-D2 sounds will be made automatically. Also, R2-D2 sounds can be
made by pressing the R2-D2 sounds button. Each time the button is pressed, R2-D2 sounds are
randomly played.
Explanation of remote control buttons
Input/output
select buttons
:
:
:
:
Button used when controlling R2-D2
or adjusting projection position
: : : :
: : : : :
Sound adjust button
:::::
:::::
Adjustment menu calling button
Default settings screen calling
button
Safety sensor
release button
R2-D2 Sound
Effects Button
Various buttons
for playing
:
:
:
:
:
:
Projected picture
adjustment::
Turns projector power ON/OFF
Turns DVD drive power ON/OFF
Turns power of iPod inserted in slot ON/OFF
When this button is pressed while in DVD mode, it changes to MEDIA mode.
Power switch
Remote control
and stand setup
Convenient functions
гг
*4 Only possible in VGA input.
Button In Projector Mode In DVD mode In iPod mode In DVI-I mode In Media mode
087(ā5ā/ 087(ā5ā/ 087(ā5ā/
Volume UP/DOWN
Volume UP/DOWN
Button In Projector Mode In DVD mode In iPod mode In DVI-I mode In Media mode
Instant chapter, track
selection
6HH³'LUHFW$FFHVVLQJ
chapter/track via the
UHPRWHFRQWURO´RQSJ
Page down (next page when using
PowerPoint)
&XUVRUĘ³PRYHFXUVRU
XS´ZKHQXVLQJ2IILFH
application)
&XUVRUĘ³PRYHFXUVRUXS´ZKHQ
using Office application)
3DJH8S³SUHYLRXV
SDJH´ZKHQXVLQJ2IILFH
application)
3DJH8S³SUHYLRXVSDJH´ZKHQ
using Office application)
&XUVRUė³PRYHFXUVRU
OHIW´ZKHQXVLQJ2IILFH
application)
&XUVRUė³PRYHFXUVRUOHIW´ZKHQ
using Office application)
(17(5³HQWHU´ZKHQXVLQJ
Office application)
(17(5³HQWHU´ZKHQXVLQJ2IILFH
application)
&XUVRUā³PRYHFXUVRU
ULJKW´ZKHQXVLQJ2IILFH
application)
&XUVRUā³PRYHFXUVRUULJKW´ZKHQ
using Office application)
STATUS (display projector
status) instant display
&XUVRUę³PRYHFXUVRUGRZQ´ZKHQ
using Office application)
AUTO ( automatic
adjustment of phase,
tracking, position) *4
AUTO ( automatic adjustment of
phase, tracking, position) *4
FM CH - (FM channel
down)
FM CH + (FM channel
up)
Repeat
FM ON/OFF (FM
broadcast start/stop)
Change multiangle
Convenient functions
Button used when adjusting sound
Remote control
and stand setup
гг
Broadcasting sound with FM transmitter
Use the “FM transmitter” to broadcast FM signal and play R2-D2 audio through component stereos and FM
radios.
5GNGEV
2TGUU
5GNGEV VJG EJCPPGN [QW YKUJ VQ RNC[ CWFKQ QP
YKVJ CPF
Selected channel will be shown on the indicator and
your screen.
Change the channel (frequency) of component stereos
or FM radios to the channel you are broadcasting from.
Pressing switch ON and OFF.
POINT Due to the broadcast output power limited by
law, the distance from which you can listen
at a good sound quality is limited.
POINT The speaker sound from R2-D2 is still ON
although the FM transmitter is broadcasting.
To turn off the sound from R2-D2, refer to
page 28 under ‘mute’.
Additional
control features
of R2-D2
CH1 88.1MHz
FM
USA / EU / JAPAN
CH1 88.1MHz
CH2 88.3MHz
CH3 88.5MHz
CH4 88.7MHz
CH5 88.9MHz
Indicator Display :Pg.72
Projector screen
For the best FM signal reception from an FM transmission signal of R2-D2, use an indoor FM antenna
instead of external FM outdoor antenna and/or cable TV line.
Caution
Turn OFF the SPDIF of DVD when using FM transmitter. Refer to page 69.
Caution