Nikko Co RP7200H Radio Controlled Toy (Receiver) User Manual 060009 Hummer Hip Hop ST39710 eng

Download:
Mirror Download [FCC.gov]
Document ID	562418
Application ID	2w4fkolFnkEwuOhu5IR6iA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	110.13kB (1376603 bits)
Date Submitted	2005-07-15 00:00:00
Date Available	2005-07-15 00:00:00
Creation Date	2005-06-21 14:07:29
Producing Software	Corel PDF Engine Version 11.633
Document Lastmod	2005-06-21 14:09:10
Document Title	060009 Hummer Hip Hop ST39710 eng
Document Creator	CorelDRAW Version 11.0

KMNA-060009
NM0-010605
RECHARGING
"WARNING! USE UNDER THE DIRECT SUPERVISION OF AN ADULT."
The newly purchased Ni-Cd pack is not charged.
Charge before operating.
Charger’s
connector
Battery’s
Connector
1. Join the connector of the charger to the connector of
the Ni-Cd battery pack.
2. Plug the charger into an electrical outlet.
3. Recharge for about 4-5 hours.
4. When the recharging is over, plug out the charger
from the electrical outlet and detach the connectors.
Charger
Press
Ni-Cd battery pack
When playing for the first time after purchase, or after a long
interval, the battery power may be weak. Even after recharging,
the playing time can be relatively short. The battery will gradually
regain power after 2 or 3 repetitions of usage and recharging.
Household
outlet
CAUTION
Do not charge Battery Pack immediately after use. Wait until it has cooled before charging.
Avoid short circuits. Short circuits will cause overheating, burning of the cords and other damages to the
battery Pack and Charger.
The Ni-Cd Battery Charger should be used for charging one Battery Pack. Do not use the Charger for
charging other type of batteries and battery packs
Do not use the Charger as a direct current outlet for other electrical appliances or machines.
Make sure that the Battery Pack and Charger are kept out of the hands of infants and small children while
charging.
Do not charge near fires, where the temperature is extremely high, or where it is wet or damp.
The charger will become slightly heated while charging. Allow sufficient free space around the Charger.
If the power of the battery pack is weak in spite of proper charging, the batteries may be worn out from
repeated use. Replace it with a new Ni-Cd battery pack.
Dispose of use Ni-Cd battery packs correctly.
Disconnect the supply before making or breaking connections to the battery.
Only use batteries or accumulators of the recommended type or a similar type.
WARNING AGAINST RECHARGING NON-RECHARGEABLE BATTERIES.
Please use this battery charger only for the charge of the rechargeable battery pack.
The Ni-Cd battery pack should be charged under the supervision of an adult.
VEHICLE
TOP VIEW
BOTTOM VIEW
PREPARATION FOR STARTING OPERATION
1. ATTACHING ANTENNA TUBE
Antenna wire
Pass the antenna wire through the antenna tube,
then insert the tube into the antenna tube holder.
If the antenna tube cannot be successfully inserted
into the antenna tube holder, try holding the root of
the antenna wire with fingers of one hand and
extending the wire with fingers of the other hand.
Antenna tube
Antenna tube holder
* Note: Be careful not to pull antenna wire too strong.
2. INSTALLING TRANSMITTER ANTENNA
Transmitter
antenna
Place the transmitter antenna into the antenna
holder to screw it in clock-wise.
Do not extend the antenna when installing. It’s
dangerous.
If the antenna is not screwed in securely, the
vehicle may move erratically. Screw the antenna
securely.
3. INSTALLING THE BATTERIES
TRANSMITTER
One 9 volt
(006P) battery
To remove the battery lid, press the
point marked “OPEN” and pull the lid
downward.
Install battery make sure that (+) and (-) poles
are positioned properly.
* Dispose the used batteries separately from
other trash.
ON
OFF
USING THE CONTROLLER
OFF
(1) Extend transmitter antenna to its
full length. The vehicle can be
controlled from a long distance
by holding the transmitter higher
with the antenna straight up.
ON
(2) Turn on the transmitter
(3) Turn “ON” the vehicle.
by operating the control
stick. (The power indicator
will light up.)
Steering
control stick
Forward / Reverse
control stick
FORWARD
LEFT / STRAIGHT / RIGHT
STOP
(NEUTRAL)
Red LED
power indicator
REVERSE
(4) Start operating the vehicle.
CAUTION:
OFF
ON
(5) Turn “OFF” the vehicle.
(6) Remove all the batteries from the vehicle and the transmitter.
ADJUSTING WORKING LIGHT FUNCTION
TO ADJUST STEERING ALIGNMENT
Adjust the steering alignment when the vehicle does not run straight forward.
Turn the steering alignment lever towards
“L” if the vehicle runs towards right.
Turn the steering alignment lever towards
“R” if the vehicle runs towards left.
7
8

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 8
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:88b18867-3421-4059-9464-8225014a6ccf
Producer                        : Corel PDF Engine Version 11.633
Modify Date                     : 2005:06:21 14:09:10+08:00
Create Date                     : 2005:06:21 14:07:29Z
Creator Tool                    : CorelDRAW Version 11.0
Metadata Date                   : 2005:06:21 14:09:10+08:00
Document ID                     : uuid:c26bfb50-6423-463e-85b0-847196eb75a4
Format                          : application/pdf
Title                           : 060009 Hummer Hip Hop ST39710 eng
Creator                         : CorelDRAW Version 11.0

EXIF Metadata provided by EXIF.tools