Nikon 1143EA 802.11 b/g Wireless Transmitter User Manual

Nikon Corporation 802.11 b/g Wireless Transmitter

Manual Pt2

13 HelpClick the Help button for online help. The “Select Action” DialogThe other options in the “Select Action” dialog are described below.  Note that the camera need not be connected to a computer to choose a printer or change the upload folder.• Change password: The dialog shown at right will be displayed.  By default, no password is required to change device pro-fi les using the WT-3 Setup Utility.  A password can be added by selecting Change password.  If the camera is later con-nected to a diff erent computer, a password prompt will be displayed.  Once the correct password has been entered, the prompt will not be displayed again.  To change an existing password, enter the old password before typing the new password.  To remove the password, select Reset password (pro-fi les will be lost) and click Next.  Please note that resetting the password deletes all existing device profi les from the camera.  Click Back to exit without changing password settings.• Setup wireless printer: By default, the system default printer for the host computer will be used when printing pictures.  To choose a diff erent printer, select Setup wireless printer (  17).• Setup picture folder: The dialog shown at right will be dis-played.  Select a destination for uploaded pictures from the following options and click Next:Use PictureProject folder: Pictures will be cataloged in PictureProject version 1.6.1 or later.Specify a diff erent folder: To choose a folder, click the   button.  The default destination is the “WT-3” folder in “My Pictures” (Windows) or “Pictures” (Macin-tosh).7  Enter the following information.• Profi le name: Enter a name of up to 16 characters.• Profi le type: Choose FTP server to confi gure the cam-era for ftp (transfer mode only), or Computer to con-fi gure the camera for use with a computer in transfer (  21), PC (  26), and print (  30) modes.• Interface type: Choose Ethernet only if the network does not include wireless, or Ethernet and Wireless for wireless or wireless and Ethernet networks.Click Next.  When a new profi le is created under Windows XP Service Pack 2, the dialog shown in Step 8 will be displayed.  With third-party LAN adapters or fi xed IP addressing, or a profi le created un-der Windows XP Service Pack 1 or Mac OS, proceed to Step 9 if Ethernet and Wireless is selected for interface type, or to Step 10 if Ethernet only is selected.Help button
148  Choose from the following options. • Automatic setup (recommended): If more than one network adapter is available, choose an adapter from the pull-down menu (if Ethernet only is selected in Step 7, the menu will list Ethernet adapters only).  Click Next.  If Ethernet and Wireless was selected in Step 7 and the com-puter is confi gured for use with an existing in-frastructure network, you will be prompted either to choose an existing infrastructure network or to set up a new ad-hoc network for use with the camera; select the desired option and click Next.  If FTP server was se-lected in Step 7, proceed to Step 11.  Otherwise proceed to Step 12. • Manual setup (for advanced users): To adjust settings manually, select this option and click Next.  If Ethernet and Wireless was selected in Step 7, proceed to Step 9.  Otherwise proceed to Step 10.9  Enter wireless network settings and click Next.• Network name (SSID): Enter a network name or choose from a list of existing networks ( 36).  Do not change the name if it is supplied automatically.• Network type: Infrastructure or ad-hoc ( 36).• Channel (ad-hoc networks only): Choose the channel (1–13) used by the host.  If channel 12 or 13 is selected for the WT-3A, channel 11 will be used instead.• Authentication: Choose the type of authentication used by the computer or access point.  The camera supports WPA-PSK, WPA2-PSK, open system, and shared key authentication.  WPA-PSK and WPA2-PSK are available only in infrastructure mode.• Encryption: Choose the type of encryption used on the network.  Depending on the authentication used, the following types of encryption are available:Open: none, 64-bit WEP, 128-bit WEP  Shared: 64-bit WEP, 128-bit WEPWPA-PSK: TKIP, AES    WPA2-PSK: AES• Encryption key: If the network uses encryption, enter the network key.  The number of the characters required depends on the type of encryption used:WEP (64-bit) WEP (128-bit) TKIP, AESNumber of characters (ASCII) 5 13 8–63Number of characters (hexadecimal) 10 26 64• Key index: In infrastructure networks that use WEP encryption, enter the host or access point key index.  The default index is 1.
15 Ad-hoc Wireless NetworksAd-hoc mode uses IP addresses beginning with 169.254.  If the computer later becomes part of an infrastructure network, it must be reconfi gured for automatic IP addressing and the camera wireless profi le modifi ed to refl ect the new settings.  Consult the network administra-tor for details.10  Enter network TCP/IP settings.• Obtain IP address automatically: Select this option if the network is confi gured to supply IP addresses automati-cally.  If the network does not include a DHCP server, addresses will be supplied by Auto IP ( 52).• IP address: If the network is confi gured for manual IP ad-dressing, enter an IP address for the WT-3.• Subnet mask: If the network is confi gured for manual IP addressing, enter a subnet mask for the WT-3.• Default gateway: If the network requires a gateway address, select this option and enter the address supplied by the network administrator.  This option applies only if FTP server is selected for Profi le type in Step 7.• DNS server: If a Domain Name Server exists on the network, select this option and enter the address supplied by the network administrator.  This option applies only if FTP server is selected for Profi le type in Step 7.Click Next.  If FTP server was selected for Profi le type in Step 7, the dialog shown in Step 11 will be displayed.  Otherwise proceed to Step 12.11  Enter ftp settings and click Next.• FTP server name: Enter the URL or IP address of the ftp server.• FTP server port: Enter the port number for the ftp server.  The default is port 21.• FTP server path: Choose the folder to which pictures will be uploaded.  If no path is specifi ed, pictures will be uploaded to the home directory.• Use anonymous login: Select this option for anonymous login, or leave this option unchecked to supply a user name and password.• Use FTP server proxy: If a proxy server is required for ftp, select this option and enter the server name and port number for the proxy server.• Passive mode: Select this option to use PASV mode.
16 MAC Address FilteringIf the network using MAC address fi ltering, the fi lter must be supplied with the MAC address of the WT-3.  After attaching the WT-3 to the camera, choose Firmware version > MAC address from the camera setup menu and note the wireless and Ethernet MAC addresses.12  Network settings will be listed as shown at right.  Click Next to proceed to Step 13, or Back to re-turn to the previous step.13  The dialog shown at right will be displayed.  Se-lect Finish wizard and click Next to exit the WT-3 Setup Utility and proceed to Step 14, or choose Select another action to perform and click Next to return to Step 5 (  12) and add or edit profi les, change the password, choose a printer, or change the upload folder.14  Turn the camera off  and disconnect the USB ca-ble. Firewall SettingsThe WT-3 uses TCP ports 20 and 21 for ftp and TCP port 15740 and UDP port 5353 when con-necting to a computer.  Computer fi rewalls must be confi gured to allow access to these ports, as otherwise the computer may not be able to access the WT-3. Profi lesA separate profi le must be created for each host and ftp server.
17Creating a Printer Profi leThe default printer for computer profi les (  13) is the system printer for the host computer.  To choose a diff erent printer, start the WT-3 Setup Utility as described in Step 4 of “Copying Network Profi les to the Camera”  (  12; there is no need to con-nect the camera to the computer), then follow the steps below. Using the PD-10See “Printing Pictures Using the PD-10 Wireless Printer Adapter” (  32) for more information on printing pictures using the PD-10.1 Select Setup wireless printer in the “Select Ac-tion” dialog and click Next.2  Choose a printer and click Next. • Windows: Select a printer from the pull-down down menu.  Printer settings can be adjusted in the Windows “Printer and Fax” dialog before printing. • Macintosh: Click Select Printer… to choose a printer and adjust printer settings.  Click Print to return to the WT-3 Setup Utility.3  Exit the WT-3 Setup Utility and disconnect the camera as described in Steps 13–14 of “Copying Network Profi les to the Camera”  (  16).
18Connecting the WT-32 Remove the power connector cover from the WT-3 and attach it to the camera strap or store it in a safe place.  Be sure to replace the power con-nector cover when the WT-3 is not in use.4 Insert the WT-3 into the camera battery chamber as shown.5 Rotate the knob in the direction shown to fasten the WT-3 securely to the camera.3 Open the camera battery chamber cover and re-move the battery, then remove the battery cham-ber cover as shown at right.Important: To ensure that the cover is not lost, place it in the WT-3 battery chamber cover holder.1 Turn the camera off  and rotate the control lock on the WT-3 to the L position.6 Open the camera USB connector cover and con-nect the USB cable from the WT-3 to the camera USB connector.
19 PB-6 BellowsA PK-13 auto-extension ring and a PB-6D spacer are required when using PB-6 bellows with the WT-3. Disconnecting the WT-3To disconnect the WT-3:1 Rotate the WT-3 control lock to the L position and turn the camera off .2 Disconnect the USB cable.3 Rotate the knob clockwise to unscrew the WT-3 from the camera tripod mount and remove the WT-3 from the camera battery chamber.4 Replace the camera battery chamber cover. The Control LockTurn the camera off  and rotate the WT-3 control lock to the L position when connecting or disconnecting the WT-3 or inserting or removing the battery.
203 Insert the battery as shown on the inside of the battery chamber cover.  The battery latch will slide aside during insertion and pop up to lock the bat-tery in place when fully inserted.Inserting the BatteryTo power the camera when the WT-3 is in place, insert the camera battery into the WT-3 battery chamber.  The WT-3 takes one EN-EL3e rechargeable Li-ion battery; other batteries can not be used.  Note that the drain on the battery is increased when the WT-3 is attached. The EH-6 AC AdapterThe optional EH-6 AC adapter can also be used to power the camera when the WT-3 is connected.  Connect the DC plug on the AC adapter to the WT-3 DC-IN connector, not to the camera.2 Open the battery chamber cover.4 Close the battery-chamber cover.5 Turn the camera on and check the battery level in the control panel or viewfi nder or using the Bat-tery Info option in the camera setup menu.1 Turn the camera off  and rotate the control lock on the WT-3 to the L position. Removing the BatteryBeing careful not to drop the battery, open the battery cham-ber cover and remove the battery as shown at right.Batery latch
21Uploading Images: Transfer ModeChoose transfer mode to upload photographs to a computer or ftp server.  The principal steps are:Upload images ......................................................................................  23–25Before connecting to the host, create a host profi le using the WT-3 Setup Utility ( 11–16) and be sure that the host is running.  Settings for connection for an ftp server can also be adjusted from the camera menus (  48–50).Connecting to the Host or ftp Server Choose PTPBefore connecting the WT-3, set the USB option in the camera setup menu to PTP (  11).1 Turn the camera off  and insert the memory card containing the pictures to be sent.Front2  To access the network via Ethernet, connect the Ethernet cable (  4).  Note that wireless transfer is disabled while an Ethernet cable is connected.  Dis-connect the Ethernet cable before accessing a wireless network.  Turn the camera off  before connecting or disconnecting the Ethernet cable.3 Turn the camera on.4 Select  Transfer mode for the Wireless trans-mitter > Mode option in the camera setup menu (  34).Connect to the host or ftp server ....................................................  21–22
22 Viewing Profi le InformationPress the camera   button to view information on the selected profi le.5 A list of available connection profi les will be dis-played.  Press the multi selector up or down to highlight the desired profi le and press to the right to select. Editing ftp Server Profi lesIf an ftp server profi le is selected, ftp settings can be ed-ited manually by pressing the camera   button.  See the Menu Guide for more information (  35).6 Choose Settings in Wireless transmitter menu to edit the following transfer options:Option DescriptionAuto send Upload photos as they are taken. 46Deleteafter send?Delete photos from camera memory card after upload. 46Send fi le as Send NEF + JPEG images as JPEG only or as NEF and JPEG. 46Send folder Upload all photos in selected folder. 47Deselect all? Deselect all images selected for upload. 477 Select  On  for  Wireless transmitter > Wireless LAN system (  34).8 Confi rm that the selected profi le is displayed in green in the top level of the wireless transmitter menu.  For information on what to do if an error is displayed, see “Troubleshooting” (  51).

Navigation menu