Nokia Solutions and Networks FXFA-01 FXFA User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	1544251
Application ID	YqJ/ukx1ud1een6G2RdPag==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	393.79kB (4922378 bits)
Date Submitted	2011-09-19 00:00:00
Date Available	2011-11-19 00:00:00
Creation Date	2011-07-08 10:51:28
Producing Software	Corel PDF Engine Version 14.1.0.195
Document Lastmod	2011-07-11 09:13:20
Document Title	Flexi Multiradio BTS GSM EDGE Stack, Wall, Pole Quick Guide.des
Document Author:	©2010 by Nokia Siemens Networks

Installing the plinth (continued)
Plinth on the pole (Note that FPKA installations is shown. See the user manual if the VMPB pole mounting kit is used.)
1. Fix the upper mounting bracket on
the pole. Attach the mounting bracket
screws (M10) on the bracket. Tighten
screws to 30 Nm.
2. Fix one side of the lower pole
mounting bracket on the plinth with
mounting screws (M8). Tighten
screws to 20 Nm.
30 Nm
20 Nm
20 Nm
3. Lift the plinth on the pole and fit it to
the mounting screws of the pole
mounting bracket. Tighten screws
(M8) to 20 Nm.
4. Place the counterpart of the lower
pole mounting bracket in its place.
Tighten screws (M10) to 30 Nm.
5. If a second plinth is required, install
it on the other side of the pole
mounting bracket.
6. Ground the plinth to the site main
ground.
Note that the length of mounting screws
depends on the diameter of the pole.
Please see the user manual for details.
30 Nm
Check list
Plinth is installed according to instructions.
Plinth is level.
4 Grounding the plinth
Grounding principle
1. Ground the plinth to the site main
ground. Tighten to 8.0-10.0 Nm (5.9-7.37 ft-lb)
2. Connect the wrist strap.
to ESD stud
Wrist strap
Check list
Local grounding (earthing) regulations are followed.
Antistatic wrist strap is used when handling modules.
Plinth is grounded.
5 Installing the casings
Side fixing plates for
Earthquake Zone 4
Note:
The casings are pre-installed
with back covers.
In Earthquake Zone 4, the
maximum number of modules
for stack installations is five.
In pole and wall installations,
the maximum modules per
plinth is two.
In pole and wall installations,
maintenance straps must be
installed in the casings.
In Earthquake Zone 4, install
M5
X 8 screws should be
side fixing plates on the casings.
secured with thread locking
In Earthquake Zone 2, the
compound in pole and wall
maximum allowed height for
installations
a stack is 22U.
1. Align the holes of the first casing
bottom with the fixing studs
on the plinth
2. Push the casing back until it stops.
3. Attach the casing to the plinth with
M5 X 8 mm screws (6150279).
Tighten to 3.5-4.2 Nm
(2.58-3.10 ft-Ib)
4. Install the remaining casings as
required by the configuration
Check list
Back covers are properly installed.
Fixing screws are tightened.
Optional: In pole and wall installations, maintenance straps are installed in the front covers.
Installing the modules
Module installation principle
1. Slide the RF module and the System Module into the casings.
2. Attach the module(s) to the casing with M5 X 25 mm screws. Tighten to 3.5-4.2 Nm (2.58-3.10 ft-Ib).
3. Install the transmission sub-module to the System Module. Tighten to 2.7-3.3 Nm (1.99-2.43 ft-Ib).
4. Install the cable entries on both casings with M5 X 10 mm screws (6150240). Torque 3.5 to 4.2 Nm.
Note: In pole and wall installations, install the maintenance strap for back covers.
Check list
Module back covers and cable entries are installed.
Screws are tightened to the specified torque value.
Note: In pole and wall installations, screws are secured with thread locking compound.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Modify Date                     : 2011:07:11 09:13:20-04:00
Create Date                     : 2011:07:08 10:51:28-05:00
Metadata Date                   : 2011:07:11 09:13:20-04:00
Format                          : application/pdf
Title                           : Flexi Multiradio BTS GSM EDGE Stack, Wall, Pole Quick Guide.des
Creator                         : ©2010 by Nokia Siemens Networks
Document ID                     : uuid:af784037-cdcc-43c0-8009-2847a23bb554
Instance ID                     : uuid:84738adb-688b-4d71-bb05-15ea2c78b53c
Producer                        : Corel PDF Engine Version 14.1.0.195
Page Count                      : 2
Author                          : ©2010 by Nokia Siemens Networks

EXIF Metadata provided by EXIF.tools