Nokia Solutions and Networks FZCWI2A1 Wireless Access Point User Manual 10 23

Download:
Mirror Download [FCC.gov]
Document ID	2797918
Application ID	1Hl4IZmkwHZjplWQYjAHXQ==
Document Description	User Manual_10.23.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	199.65kB (2495607 bits)
Date Submitted	2015-10-29 00:00:00
Date Available	2015-10-29 00:00:00
Creation Date	2015-10-23 11:07:15
Producing Software	Adobe PDF library 9.90
Document Lastmod	2015-10-23 16:12:21
Document Title	User Manual_10.23.pdf
Document Creator	Adobe Illustrator CS5

Nokia Wi-Fi Access Point WI2A-AC200i
5G
Thank you for buying a Nokia Wi-Fi Access Point WI2A-AC200i.
2.4G
This Quick Installation Guide Nokia Wi-Fi Access Point WI2A-AC200i provides basic
information and step-by-step installation instructions. Following these steps will
enable you to properly install the WI2A-AC200i at your site.
ETH
CTRL
PWR
Pre-requisites
• Please read all the notes and safety statements in this guide before beginning the installation process.
• The WI2A-AC200i is designed for an indoor environment (e.g. temperature range of 0°C to 40°C, non-condensing).
• Allow 10 cm of space around the access point to ensure proper cooling.
• Install the WI2A-AC200i away from heat sources, water/wet surfaces, and strong magnetic field sources or electrical appliances
(ex: microwave ovens).
• Using an incorrect power adapter may permanently damage the product.
5 GHz
2.4 GHz
Legal Notices
• Nokia Solutions and Networks 2015.
©
The information contained herein is subject to change without notice. The only warranties for Nokia products and services are set
forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as
constituting an additional warranty. Nokia Solutions and Networks shall not be liable for technical or editorial errors or omissions
contained herein.
ETH
Label Statements
CTRL
Label material and adhesive have been designed to last the lifetime of the product when installed in accordance with Nokia
installation guidelines.
Package Contents
•
•
•
•
•
Access point
Bracket
Logo sticker
Quick Installation Guide
Regulatory Information
Tools Required
•
•
•
•
•
Marker
Measuring tape
Screws
Screw driver
Hammer
Color – Indication
LED
PWR
Accessories Needed
• Network cables
• POE power or DC power adapter
Off - No SSID Configured on 5 GHz
Green - 5 GHz SSID Configured and Broadcasting
Red – AP is locked by Controller
Off - No SSID Configured on 2.4 GHz
Green - 2.4 GHz SSID Configured and Broadcasting
Red – AP is locked by Controller
Off - LAN Connection Not Detected
Red - LAN Connection Detected
Red blinking - AP IP address Discovery process
Green - AP IP address obtained (DHCP or Static but not factory default)
Green blinking - LAN Activity after IP address has been obtained
Off - LAN Connection Not Detected or AP IP Address not available
Red - AP IP address available but Controller IP is being discovered or Invalid Controller IP
Red blinking - Controller IP Available and Connection in Progress
Green -Connected to Controller and in steady state
Green blinking - Connected to Controller and Configuration in Progress
Amber blinking - Connected to Controller and Software Download in Progress
Off - No Power to AP
Red - Board Power On
Red blinking - Loading Software
Green - Software Loaded
Red blinking for more than 5 minutes - Failure to load Software properly (if LED control is working)
Specification Summary
The following table describes the physical, electrical and environmental specifications.
1. Before unpacking the carton, ensure that the packaging is intact, not damaged or soaked.
2. Unpack the carton and check if all the items listed in the package contents are included.
NOTE
3. Tools are not supplied with the WI2A-AC200i box.
Description
LAN PORT
Port for Ethernet cable to connect the WI2A-AC200i to LAN and POE (if available).
Reset button
Used to reboot or restore WI2A-AC200i. Press and release the button to reboot WI2A-AC200i.
Press and hold the button for 10 seconds to restore factory settings.
Power port
Security Lock Slot
Dimensions
150mm x 150mm x 30mm (without bracket)
Item
Description
400g
Nokia WI2A-AC200i electrical specification
Name
Item
Weight
Product Overview
Number
Nokia WI2A-AC200i physical specification
Port to connect a DC power supply unit if POE is unavailable.
Slot for security lock and cable for theft protection.
Power input
Power consumption
Description
+12V/1A
≤12W
Nokia WI2A-AC200i environmental specification
Item
Description
Working temperature
0°C ~ +40°C
Operating humidity
5% to 95% non-condensing
Dustproof and Waterproof
IP20
2
Hardware Operation
The Nokia® WI2A-AC200i can be ceiling or wall mounted. Ceiling mounting is recommended.
Please read the safety instructions before working with the product.
Scenario 2: Wall mounting
1. Align the securing hook of WI2A-AC200i with the bracket.
2. To firmly fasten the WI2A-AC200i to the bracket, rotate the bracket in the clockwise direction
(as shown in the figure on the right) until it completely locks into the WI2A-AC200i.
3. Drive two screws in the wall with a distance of 79mm between them.
4. Align the bracket hole with the screws, and then pull the bracket down over the screws until it is
tightly fastened.
Ensure that Nokia WI2A-AC200i is securely installed. Poor installation may cause the device to fall and be damaged.
NOTE
79mm
Securing Hook
Connecting cables
The following figure illustrates the interface and cable connections of the WI2A-AC200i:
Item
Description
Name
NOTE
• Category-5 Enhanced Ethernet cable is recommended.
Ethernet cable
DC Power adapter
Downward
Recommended wall mounting for the WI2A-AC200i is with the cables run upward.
• Ensure that the WI2A-AC200i is connected to the LAN using a correct Ethernet cable.
If the cables are run downward, the Nokia Logo sticker can be placed on the
WI2A-AC200i to display an upright Nokia logo.
Cabling options are shown in the figure to the right.
• The WI2A-AC200i might fail to power up or work if non-standard Ethernet cable is used.
Placing of Nokia Logo sticker while wall mounting
• A DC power adapter is required only if a PoE power supply is not available.
• To connect the WI2A-AC200i to a DC power source and prevent damage, use the power adapter specified
for the WI2A-AC200i.
The WI2A-AC200i requires either PoE or DC power supply to operate.
To use the PoE power supply:
Connect the WI2A-AC200i to the PoE power supply (such as PoE injector or PoE switch) using an Ethernet cable.
Logo sticker
Upward
Installing the security lock
There is a security lock slot with an anti-theft design provided on the WI2A-AC200i.
1. Fasten the security lock cable to an immovable object.
2. Insert the security lock cable into the security lock slot of the WI2A-AC200i and then lock it.
To use the DC power supply:
Connect the WI2A-AC200i to the DC power supply.
Use only PoE and DC power supplies that meet these specifications:
PoE
DC Power Adapter
NOTE
PD: 12.95W, support Category-5 Enhanced 100m cable
Voltage range: 37V~ 57V
12 V DC nominal, +/- 5%
Scenario 1: Ceiling mounting
1. Choose a pair of bracket clips to firmly mount the bracket with
the T-rails.
The bracket provides two pairs of clips. Select the correct
pair based on the T-rail width. The following figure
NOTE illustrates the bracket clips.
Bracket Clips1
2. Align the securing hook of the WI2A-AC200i with the
secured bracket.
3. To firmly fasten the WI2A-AC200i with the bracket, rotate
the WI2A-AC200i in the anti-clockwise direction.
Securing
Hook
Bracket Clips2
T-rail
The box does not include a security lock cable. It needs
to be purchased separately.
Security lock slot
Security lock cable

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Adobe PDF library 9.90
Create Date                     : 2015:10:23 11:07:15+09:00
Modify Date                     : 2015:10:23 16:12:21+08:00
Creator Tool                    : Adobe Illustrator CS5
Metadata Date                   : 2015:10:23 16:12:21+08:00
Thumbnail Width                 : 192
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 15777 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : Nokia®_AC200i-QIG-front_V1.5
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : True
Max Page Size W                 : 419.999514
Max Page Size H                 : 289.999870
Max Page Size Unit              : Millimeters
Font Name                       : Arial-BoldMT, ArialMT, Arial-BoldItalicMT
Font Family                     : Arial, Arial, Arial
Font Face                       : Bold, Regular, Bold Italic
Font Type                       : Open Type, Open Type, Open Type
Font Version                    : Version 5.20, Version 5.20, Version 5.20
Font Composite                  : False, False, False
Font File Name                  : arialbd.ttf, arial.ttf, arialbi.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : 默认色板组
Swatch Groups Group Type        : 0
Swatch Groups Colorants Swatch Name: Raid Controller Orange
Swatch Groups Colorants Type    : SPOT
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Cyan    : 0.000000
Swatch Groups Colorants Magenta : 26.999998
Swatch Groups Colorants Yellow  : 100.000000
Swatch Groups Colorants Black   : 1.000000
Document ID                     : xmp.did:E3CB8A263379E511B2F8BE576D4E7267
Instance ID                     : uuid:577553ca-0aa6-4e45-b4c6-2337e3bb52e3
Original Document ID            : xmp.did:D3751531D8FAE411B0CE92602E7A2110
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:3f6aa1fa-22a9-47c0-b9aa-9357a400e25e
Derived From Document ID        : xmp.did:F3E2BE442376E511B7F8EFE62FC94016
Derived From Original Document ID: xmp.did:D3751531D8FAE411B0CE92602E7A2110
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:D3751531D8FAE411B0CE92602E7A2110, xmp.iid:e62b4829-4448-5141-b17c-de9a2f09372d, xmp.iid:CBB0E152463FE511979284F63E256D3C, xmp.iid:258AC201F93FE511B15D8C407FDCBED8, xmp.iid:9357078F5951E5118B949419DF866E80, xmp.iid:127BBCADC670E511A04CEC82868D9361, xmp.iid:F3E2BE442376E511B7F8EFE62FC94016, xmp.iid:E3CB8A263379E511B2F8BE576D4E7267
History When                    : 2015:05:19 14:57:22+08:00, 2015:08:05 12:31:38+05:30, 2015:08:10 17:58:37+08:00, 2015:08:11 15:17:21+08:00, 2015:09:02 18:01:19+08:00, 2015:10:12 17:50:32+08:00, 2015:10:19 13:35:55+08:00, 2015:10:23 11:07:10+08:00
History Software Agent          : Adobe Illustrator CS5, Adobe Illustrator CC 2015 (Windows), Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5
History Changed                 : /, /, /, /, /, /, /, /
Page Count                      : 2
Creator                         : Adobe Illustrator(R) 15.0
For                             : Pan Xiaoyan,
Bounding Box                    : -1 -383 1217 1237
Container Version               : 11
Creator Version                 : 15

EXIF Metadata provided by EXIF.tools