Nokia of America BBTRX-21 PCS LTE 9764 Metro Cell Outdoor Transceiver System User Manual

Alcatel-Lucent USA Inc. PCS LTE 9764 Metro Cell Outdoor Transceiver System

User Manual

APPLICANT:  Alcatel-Lucent USA Inc.      -13  -    FCC ID: AS5BBTRX-21 Alcatel-Lucent USA Inc. - Proprietary Use pursuant to Company Instructions.  13  Exhibit 6 – Instruction Book   Confidential   SECTION 2.1033(c) (3) A copy of the installation and operating instructions to be furnished the user. A draft copy of the instructions may be submitted if the actual document is not available. The actual document shall be furnished to the FCC when it becomes available.   Response:  The installation and operating instructions for the Alcatel-Lucent’s PCS LTE 9764 Metro Cell Outdoor Transceiver System FCC ID: AS5BBTRX-21  is attached.   The  Installation Manual in this exhibit,  Alcatel-Lucent 9764 Metro Cell Outdoor LTE 2x1W and 2x2W Hardware Installation, 3MN-01707-0002-RJZZA Issue 3.05 | October 2014,  is not furnished to the user, except under very exceptional and very limited circumstances.  This manual contains highly proprietary circuit, equipment and architecture descriptions that must not be made available for public inspection.    The cover/title page is explicitly labeled:   “Alcatel-Lucent – Internal Proprietary – Use pursuant to Company instruction”.   This information is proprietary both to Alcatel- Lucent and to Alcatel- Lucent’s contracted manufacturer/supplier.     (ALCATEL-LUCENT USA CONFIDENTIAL PROPRIETARY INFORMATION)
Title pageAlcatel-Lucent 9764Metro Cell Outdoor LTE 2x1W and 2x2WHardware Installation3MN-01707-0002-RJZZAIssue 3.05 | October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionProprietary Use pursuant to Company instructionDRAFTDRAFT
Legal noticeLegal noticeAlcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respectiveowners.The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.Copyright © 2014 Alcatel-Lucent. All rights reserved.Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outsideAlcatel-Lucent without its written authorization.Proprietary Use pursuant to Company instructionAlcatel-Lucent – InternalProprietary – Use pursuant to Company instructionDRAFTDRAFT
ContentsAbout this documentPurpose .......................................................................................................................................................................................... xiiixiiiWhat's new ................................................................................................................................................................................... xiiixiiiIntended audience ...................................................................................................................................................................... xivxivSupported systems ..................................................................................................................................................................... xivxivHow to use this document ....................................................................................................................................................... xivxivSafety information ..................................................................................................................................................................... xivxivPrerequisites ................................................................................................................................................................................. xivxivConventions used ......................................................................................................................................................................... xvxvRelated information ................................................................................................................................................................. xviixviiDocument support ...................................................................................................................................................................... xixxixTechnical support ....................................................................................................................................................................... xixxixHow to order .................................................................................................................................................................................. xxxxHow to comment .......................................................................................................................................................................... xxxx1Safety statementsOverview ...................................................................................................................................................................................... 1-11-1Structure of safety statements ............................................................................................................................................... 1-21-2Safety ........................................................................................................................................................................................... 1-41-4Safety - specific hazards ......................................................................................................................................................... 1-51-5Product safety ............................................................................................................................................................................. 1-91-92Product overviewOverview ...................................................................................................................................................................................... 2-12-1Functional description ............................................................................................................................................................. 2-22-2....................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction iiiDRAFTDRAFT
Physical description ................................................................................................................................................................. 2-42-4Supported installation options ........................................................................................................................................... 2-132-13Hardware and ancillary items ............................................................................................................................................ 2-172-173Installation of the 9764 Metro DockOverview ...................................................................................................................................................................................... 3-13-19764 Metro Dock pre-installationOverview ...................................................................................................................................................................................... 3-23-29764 Metro Dock Pre-installation information .............................................................................................................. 3-33-3Pole mount installation requirements ................................................................................................................................ 3-53-5Wall mount installation requirements ................................................................................................................................ 3-93-9Pair mount and daisy chain requirements ...................................................................................................................... 3-133-139764 Metro Dock installationOverview ................................................................................................................................................................................... 3-183-18Procedure 3-1: Pole mount the 9764 Metro Dock ...................................................................................................... 3-193-19Procedure 3-2: Pole mount the 9764 Metro Dock using optional tilt brackets ................................................ 3-253-25Procedure 3-3: Wall mount the 9764 Metro Dock ..................................................................................................... 3-353-35Procedure 3-4: Wall mount the 9764 Metro Dock using optional tilt brackets ............................................... 3-403-40Procedure 3-5: Pole mount the 9764 Metro Dock in a pair configuration ........................................................ 3-543-54Procedure 3-6: Wall mount the 9764 Metro Dock in a pair configuration ........................................................ 3-713-719764 Metro Dock cablingOverview ................................................................................................................................................................................... 3-893-89Procedure 3-7: 9764 Metro Dock ground cabling ...................................................................................................... 3-903-90Procedure 3-8: 9764 Metro Dock Ethernet cabling - fiber optic .......................................................................... 3-923-92Procedure 3-9: 9764 Metro Dock Ethernet cabling - electrical ............................................................................. 3-993-999764 Metro Dock post-installationOverview ................................................................................................................................................................................. 3-1113-111Contents........................................................................................................................................................................................................................................................................................................................................................................................................................................................................iv Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 3-10: Final installation activities and checks ........................................................................................ 3-1123-1124Installation of the 9764 MCO moduleOverview ...................................................................................................................................................................................... 4-14-19764 MCO pre-installationOverview ...................................................................................................................................................................................... 4-24-2Pre-installation information .................................................................................................................................................. 4-34-39764 MCO cablingOverview ...................................................................................................................................................................................... 4-44-4Procedure 4-1: Connect external RF antenna to the Alcatel-Lucent 9764 MCO LTE 2x2W ....................... 4-54-5Procedure 4-2: Connect GPS antenna ............................................................................................................................... 4-74-7Procedure 4-3: 9764 MCO module ground cabling ................................................................................................... 4-184-18Site power requirements (AC) ........................................................................................................................................... 4-214-21Site power requirements (DC) ........................................................................................................................................... 4-244-24Product power requirements ............................................................................................................................................... 4-274-27Procedure 4-4: Connect power cable .............................................................................................................................. 4-294-299764 MCO installationOverview ................................................................................................................................................................................... 4-404-40Procedure 4-5: Attach 9764 MCO module to 9764 Metro Dock .......................................................................... 4-414-41Procedure 4-6: Orient 9764 MCO module ................................................................................................................... 4-484-489764 MCO post-installationOverview ................................................................................................................................................................................... 4-504-50Procedure 4-7: Post installation activities ..................................................................................................................... 4-514-51Procedure 4-8: Power on the 9764 MCO ...................................................................................................................... 4-524-52ALED State DescriptionOverview ..................................................................................................................................................................................... A-1A-1LED status for 9764 MCO LTE ......................................................................................................................................... A-2A-2Contents........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction vDRAFTDRAFT
BInstallation of the 9764 MCO Wi-Fi APOverview ..................................................................................................................................................................................... B-1B-1Physical description ................................................................................................................................................................ B-2B-29764 MCO Wi-Fi AP pre-installation information ...................................................................................................... B-8B-8Procedure B-1: Remove 9764 MCO module from 9764 Metro Dock ................................................................. B-9B-9Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764 MCO module ................................................. B-19B-19LED state description - 9764 MCO Wi-Fi AP ............................................................................................................ B-25B-25CProduct conformance statementsOverview ..................................................................................................................................................................................... C-1C-1United States complianceIntroduction ................................................................................................................................................................................ C-2C-2Federal Communications Commission ............................................................................................................................ C-3C-3Product safety and RF exposure ......................................................................................................................................... C-4C-4FDA/IEC optical transmitter product compliance statements ................................................................................. C-5C-5Eco-environmental statements ............................................................................................................................................ C-6C-6European UnionIntroduction ................................................................................................................................................................................ C-7C-7CE marking ................................................................................................................................................................................ C-8C-8EMC and radio spectrum compliance .............................................................................................................................. C-9C-9Product safety and RF exposure ....................................................................................................................................... C-10C-10Eco-environmental statements .......................................................................................................................................... C-13C-13DDocument issue historyOverview ..................................................................................................................................................................................... D-1D-1Document issue history ......................................................................................................................................................... D-2D-2GlossaryIndexContents........................................................................................................................................................................................................................................................................................................................................................................................................................................................................vi Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
List of tables1Document changes from Issue 3.03, September 2014 ................................................................................. xiiixiii2Terminology .................................................................................................................................................................. xvxv3Related documents ................................................................................................................................................... xviixvii2-1 GPS antenna options .............................................................................................................................................. 2-112-113-1 Pole mount installation kits and brackets ......................................................................................................... 3-63-63-2 Wall mount installation brackets .......................................................................................................................... 3-93-94-1 Power materials ....................................................................................................................................................... 4-274-27B-1 9764 MCO Wi-Fi AP physical characteristics ............................................................................................... B-4B-4B-2 9764 MCO Wi-Fi AP LEDs during boot-up ................................................................................................. B-25B-25B-3 9764 MCO Wi-Fi AP LEDs based on Admin status and WLAN mapping ...................................... B-26B-26B-4 9764 MCO Wi-Fi AP LEDs during normal operation states .................................................................. B-27B-27C-1 Distances corresponding to reference levels for the general public and workers at maximum Txpower ....................................................................................................................................................................... C-11C-11C-2 Distances corresponding to reference levels for the general public and workers at maximum Txpower ....................................................................................................................................................................... C-12C-12D-1 Document changes from Issue 3, September 2014 ...................................................................................... D-2D-2D-2 Document changes from Issue 2,June 2014 .................................................................................................... D-2D-2D-3 Document changes from Issue 1.06, May 2014 ............................................................................................ D-3D-3D-4 Document changes from Issue 1.05, May 2014 ............................................................................................ D-3D-3D-5 Document changes from Issue 1.04, April 2014 ........................................................................................... D-4D-4D-6 Document changes from Issue 1.03, February 2014 ................................................................................... D-4D-4D-7 Document changes from Issue 1.02, January 2014 ...................................................................................... D-4D-4D-8 Document changes from Issue 1.01, December 2013 ................................................................................. D-5D-5D-9 Document changes from Issue 1, November 2013 ...................................................................................... D-5D-5....................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction viiDRAFTDRAFT
List of tables........................................................................................................................................................................................................................................................................................................................................................................................................................................................................viii Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
List of figures2-1 9764 Metro Dock and 9764 MCO LTE 2x1W and Alcatel-Lucent 9764 Metro Cell Outdoor LTE2x2W ........................................................................................................................................................................... 2-42-42-2 9764 MCO LTE with 9764 MCO Wi-Fi AP .................................................................................................... 2-52-52-3 9764 MCO LTE module connection interfaces .............................................................................................. 2-92-92-4 9764 MCO LTE module connection interfaces - double lug ground point detail .............................. 2-92-92-5 Installation examples ............................................................................................................................................. 2-132-132-6 9764 MCO Wi-Fi AP module attached to 9764 MCO LTE module (front view) ........................... 2-142-142-7 9764 MCO daisy chain installation example ................................................................................................ 2-152-152-8 9764 MCO pair-mount installation example ................................................................................................. 2-162-163-1 Pole mount banding and brackets ........................................................................................................................ 3-63-63-2 9764 Metro Dock pole mount using screws .................................................................................................... 3-73-73-3 9764 Metro Dock pole mount using banding .................................................................................................. 3-83-83-4 Double 9764 Metro Dock pole mount ............................................................................................................... 3-83-83-5 Wall mount brackets ............................................................................................................................................... 3-103-103-6 9764 Metro Dock wall mount (no tilt) ............................................................................................................. 3-113-113-7 9764 Metro Dock wall mount (with tilt) ......................................................................................................... 3-113-113-8 Double 9764 Metro Dock wall mount ............................................................................................................. 3-123-124-1 External GPS antenna configuration .................................................................................................................. 4-74-74-2 External GPS antenna connector ....................................................................................................................... 4-104-104-3 GPS antenna connection ...................................................................................................................................... 4-104-104-4 Weatherproof tape placement for external GPS antenna .......................................................................... 4-114-114-5 Internal and external GPS antenna connectors ............................................................................................. 4-124-124-6 GPS antenna connection ...................................................................................................................................... 4-134-134-7 Weatherproof tape placement for external GPS antenna .......................................................................... 4-144-14....................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction ixDRAFTDRAFT
4-8 Bridge cable between external and internal GPS antenna connectors ................................................. 4-154-154-9 Internal/external GPS antenna connector ....................................................................................................... 4-164-164-10 Weatherproof tape placement for external GPS antenna .......................................................................... 4-174-174-11 connection interfaces ............................................................................................................................................. 4-294-29A-1 Location of LED ....................................................................................................................................................... A-2A-2B-1 9764 MCO Wi-Fi AP attached to 9764 MCO hardware variants ............................................................ B-2B-2B-2 9764 MCO Wi-Fi AP - closed housing ............................................................................................................. B-3B-3B-3 9764 MCO Wi-Fi AP - cutaway view ............................................................................................................... B-3B-3B-4 9764 MCO Wi-Fi AP connection point on 9764 MCO .............................................................................. B-5B-5B-5 9764 MCO Wi-Fi AP connected to 9764 MCO (cutaway side view) ................................................... B-5B-5B-6 9764 Metro Dock to LTE 9764 MCO module grounding cable ........................................................... B-13B-13B-7 Key extension .......................................................................................................................................................... B-13B-13B-8 Pull 9764 MCO module from Metro Dock ................................................................................................... B-16B-16B-9 AC power line connector ..................................................................................................................................... B-16B-16B-10 DC power line connector ..................................................................................................................................... B-17B-17B-11 9764 MCO Wi-Fi AP module attached to 9764 MCO module .............................................................. B-17B-17B-12 Wi-Fi AP connector cover on 9764 MCO module ..................................................................................... B-21B-21B-13 Wi-Fi AP connector on 9764 MCO module ................................................................................................. B-21B-21B-14 9764 MCO Wi-Fi AP module attached to 9764 MCO module .............................................................. B-22B-22List of figures........................................................................................................................................................................................................................................................................................................................................................................................................................................................................xAlcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
List of procedures3 Installation of the 9764 Metro Dock3-1 Pole mount the 9764 Metro Dock ..................................................................................................................... 3-193-193-2 Pole mount the 9764 Metro Dock using optional tilt brackets ............................................................... 3-253-253-3 Wall mount the 9764 Metro Dock ..................................................................................................................... 3-353-353-4 Wall mount the 9764 Metro Dock using optional tilt brackets ............................................................... 3-403-403-5 Pole mount the 9764 Metro Dock in a pair configuration ........................................................................ 3-543-543-6 Wall mount the 9764 Metro Dock in a pair configuration ....................................................................... 3-713-713-7 9764 Metro Dock ground cabling ..................................................................................................................... 3-903-903-8 9764 Metro Dock Ethernet cabling - fiber optic .......................................................................................... 3-923-923-9 9764 Metro Dock Ethernet cabling - electrical ............................................................................................ 3-993-993-10 Final installation activities and checks .......................................................................................................... 3-1123-1124 Installation of the 9764 MCO module4-1 Connect external RF antenna to the Alcatel-Lucent 9764 MCO LTE 2x2W ...................................... 4-54-54-2 Connect GPS antenna ............................................................................................................................................... 4-74-74-3 9764 MCO module ground cabling .................................................................................................................. 4-184-184-4 Connect power cable .............................................................................................................................................. 4-294-294-5 Attach 9764 MCO module to 9764 Metro Dock ......................................................................................... 4-414-414-6 Orient 9764 MCO module .................................................................................................................................. 4-484-484-7 Post installation activities ..................................................................................................................................... 4-514-514-8 Power on the 9764 MCO ...................................................................................................................................... 4-524-52B Installation of the 9764 MCO Wi-Fi APB-1 Remove 9764 MCO module from 9764 Metro Dock ................................................................................. B-9B-9B-2 Attach 9764 MCO Wi-Fi AP module to 9764 MCO module ................................................................. B-19B-19....................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction xiDRAFTDRAFT
List of procedures........................................................................................................................................................................................................................................................................................................................................................................................................................................................................xii Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
About this documentAbout this documentPurposeThe purpose of this document is to provide hardware installation instructions for anAlcatel-Lucent 9764 Metro Cell Outdoor LTE 2x1W and an Alcatel-Lucent 9764 MetroCell Outdoor LTE 2x2W.Procedures are provided for mounting, grounding, powering, and cabling the 9764 MCOLTE 2x1W and the 9764 MCO LTE 2x2W.What's newThis is Issue 3.05 of Alcatel-Lucent Metro Cell Outdoor LTE 2x1W and 2x2W HardwareInstallation, 3MN-01707-0002-RJZZA.The major changes introduced in this issue of the document are described in the followingparagraphs. Changes introduced in prior issues of the document are shown in AppendixD, “Document issue history”Issue 3.05 (October 2014) - Document changes from the previous releaseThe document changes from Issue 3.03, September 2014 are shown in the followingtable:Table 1 Document changes from Issue 3.03, September 2014Feature/enhancement Description LocationDocumentation changesConnect GPS antenna Added information and steps forusing weatherproof tape whenattaching external GPS antenna.“Connect external GPS antenna - B25, B7 or B2MCO” (p. 4-9)“Connect external GPS antenna to MCO - B3MCO” (p. 4-12)“Connect internal/external GPS antenna toAlcatel-Lucent 9764 MCO LTE 2x2W” (p. 4-15)Hardware andAncillary itemsAdded information aboutweatherproof tape when attachingexternal GPS antenna in the Externalantenna – GPS table.“Hardware and ancillary items” (p. 2-17)...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction xiiiDRAFTDRAFT
Intended audienceThe audience for this document is Installation personnel.Supported systemsThis document applies to the following Alcatel-Lucent 9764 Metro Cell Outdoor LTE2x1W and Alcatel-Lucent 9764 Metro Cell Outdoor LTE 2x2W products:•Alcatel-Lucent 9764 Metro Cell Outdoor V1.0 B25 LTE 2x1W•Alcatel-Lucent 9764 Metro Cell Outdoor V1.1 B2 LTE 2x1W•Alcatel-Lucent 9764 MCO V1.1 B2/B25 LTE 2x1W•Alcatel-Lucent 9764 Metro Cell Outdoor V1.1 B7 LTE 2x1W•Alcatel-Lucent 9764 Metro Cell Outdoor V1.1 B2 LTE 2x2W•Alcatel-Lucent 9764 Metro Dock.How to use this documentStart with the first chapter and work through the manual to the end. Once you have donethis, you will have carried out the hardware installation completely and in the propersequence.Prior to installing the equipment, the installer should be familiar with the safetyprecautions, warnings, and product conformance statements. Required tools and materialsrecommended for installation, and a process checklist, are listed in topic “Pre-installationinformation” .Safety informationFor your safety, this document contains safety statements. Safety statements are given atpoints where risks of damage to personnel, equipment, and operation may exist. Failure tofollow the directions in a safety statement may result in serious consequences.PrerequisitesNoneAbout this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................xiv Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Conventions usedVocabulary conventionsThe following vocabulary conventions are also used when referring to Alcatel-Lucentproducts:Table 2 TerminologyTerm Description/Meaning9764 MCO The 9764 MCO consists of the following modules: 9764 MetroDock module, and the 9764 MCO WCDMA module.9764 Metro Dock Refers to the Alcatel-Lucent 9764 Metro Dock, a module supportingbackhaul for the 9764 MCO.9764 MCO LTE Refers to the module that contains the complete base station,including baseband unit, radio unit and antenna. It is attached to thefront of the 9764 Metro Dock to form the 9764 MCO.9764 MCO V1.1B2/B25 LTE 2x1WRefers to the Band 2/Band 25 (combined) 2x1W variant of the 9764MCO LTE that is the focus of this document.9764 MCO V1.1 B2LTE 2x2WRefers to the Band 2 2x2W variant of the 9764 MCO LTE that is thefocus of this document.Typographical conventionsThe typographical conventions used in this document are described in the following table.Appearance Descriptionemphasis Text that is emphasizeddocument titles Titles of books or other documentsgraphical user interface text Text that is displayed in a graphical userinterfacevariablesA value or command-line parameter that theuser providesTechnical conventionsLengths and other measurements are given in metric units, with non-metric units given asequivalents for use in non-metric markets.About this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction xvDRAFTDRAFT
For manufactured parts, the following system of conventions is used:•Metric sizes of nuts, bolts, flat washers, and lock washers are identified by anuppercase letter M followed immediately by a size in millimeters (example: M10)•American fractional sizes of nuts, bolts, anchor bolts, and washers are identified by anumber followed immediately by a double apostrophe (example: 3/8"). In the case oflengths measured in feet, “2 feet” is used rather than “2'” so that the single apostropheis not overlooked.The illustrations in this document do not contain all details and exceptions, but areintended to highlight main points. Dimensions are usually shown in millimeters, withinches in parenthesis. As an example, 680.0 (26.77) equals 680 millimeters or 26.77inches.Wire gauges are specified in metric units. Equivalent sizes in the American Wire Gauge(AWG) system are given in the following table:Standard cross-sections and wire diameter of round copper conductorsThe following table is from CEI/IEC 60947-1:2004, Table 1, Standard cross-sections ofround copper conductors and approximate relationship between mm2and AWG/kcmilsizes for reference. Additional wire sizes are included in this document as appropriate forthe topic.ISO rated cross-sectional area (mm2) AWG/kcmil size0.2 240.34 220.5 200.75 181-1.5 162.5 1441261010 816 625 435 2-150 0 (1/0)70 00 (2/0)About this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................xvi Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
ISO rated cross-sectional area (mm2) AWG/kcmil size95 000 (3/0)- 0000 (4/0)120 250 kcmil150 300 kcmil185 350 kcmil- 400 kcmil240 500 kcmil300 600 kcmilNOTE: The dash, when it appears, counts as a size when considering connecting capacity (see7.1.7.2 in the standard).Related informationFor information on subjects related to the content of this document, refer to thedocuments listed in the following table:Table 3 Related documentsRefer to this document At this location For more informationonAlcatel-Lucent 9764 Metro CellOutdoor LTE 2x1W and 2x2W SitePreparation, 3MN-01707-0001-RJZZA9764 MCO LTE (Metro Cell Outdoor forLTE) (https://support.alcatel-lucent.com/portal/productContent.do?entryId=1-0000000003997)9764 MCO LTE 2x1W sitepreparationAlcatel-Lucent 9764 Metro CellOutdoor LTE 2x1W and 2x2WTechnical Description9YZ-04152-0056- DEZZA(LR13.3.L)9YZ-05817-0056- DEZZA(LR14.1.L)9764 MCO LTE (Metro Cell Outdoor forLTE) (https://support.alcatel-lucent.com/portal/productContent.do?entryId=1-0000000003997)9764 MCO LTE 2x1Wtechnical overviewAlcatel-Lucent 9764 Metro CellOutdoor LTE 2x1W and 2x2WMaintenance and Troubleshooting9YZ-04152-0057-REZZA(LR13.3.L)9YZ-05817-0057-REZZA(LR14.1.L)9764 MCO LTE (Metro Cell Outdoor forLTE) (https://support.alcatel-lucent.com/portal/productContent.do?entryId=1-0000000003997)9764 MCO LTE 2x1Wmaintenance andtroubleshootingAbout this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction xviiDRAFTDRAFT
Table 3 Related documents (continued)Refer to this document At this location For more informationonAlcatel-Lucent 9772 Wi-Fi ServiceController V1.0 L HardwareInstallation, 3MN-01840-0001-RJZZAOnLine Customer Support (OLCS)(http://support.alcatel-lucent.com)Instructions for installingthe 9772 WiSC-Lhardware and accessing itsmanagement interfaces.Alcatel-Lucent 9764 and 9772Metro Cell Outdoor Wi-Fi AP andWi-Fi Service Controller, ReleaseWA5.5, System Reference Guide,3MN-01840-0002-RKZZAOnLine Customer Support (OLCS)(http://support.alcatel-lucent.com)Instructions for accessingand using the web-basedgraphic user interface(GUI) tomanage/administer the9772 Wi-Fi ServiceController and 9764 MCOWi-Fi Access PointAlcatel-Lucent 9764 and 9772,Metro Cell Outdoor Wi-Fi AP andWi-Fi Service Controller, ReleaseWA 5.5, CLI Reference Guide,3MN-01840-0003-RKZZAOnLine Customer Support (OLCS)(http://support.alcatel-lucent.com)Instructions for accessingand using command lineinterface (CLI) tomanage/administer the9772 Wi-Fi ServiceController and 9764 MCOWi-Fi Access Point.Library for LTE End-to-EndSolutionLTE End-to-End Solution(https://infoproducts.alcatel-lucent.com/aces/cgi-bin/dbaccessproddoc.cgi.edit?entryId=1-0000000001078)The full collection ofdocuments in the LTEcollectionAlcatel-Lucent LTE Radio AccessNetwork (RAN) eNodeB Macroand Metro Products Release FDDRelease Notes9YZ-05817-0001-FMZZA(LR13.3.L)9YZ-04152-0001-FMZZA(LR14.1.L)LTE End-to-End Solution(https://infoproducts.alcatel-lucent.com/aces/cgi-bin/dbaccessproddoc.cgi.edit?entryId=1-0000000001078)Release specific softwareand feature statusinformation9764 lightRadio Metro CellOutdoor “Family” Model OfferProvisioning Guide,BCR/IRC/APP/038681Subject to non-disclosure agreement andavailable from Alcatel-LucentrepresentativesProduct ordering codesAbout this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................xviii Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Table 3 Related documents (continued)Refer to this document At this location For more informationonFDD eNodeB Product EngineeringGuide, LTE/DCL/APP/041927Subject to non-disclosure agreement andavailable from Alcatel-LucentrepresentativesThe differentAlcatel-Lucent LTEeNodeB hardwareconfigurations and therelated engineering rulesand guidelines.Grounding and LightningProtection Guidelines forAlcatel-Lucent Wireless SystemCell Sites, 401-200-115OnLine Customer Support (OLCS)(http://support.alcatel-lucent.com)Grounding and Lightningprotection systemsStandard for Installation ofLightning Protection Systems,NFPAANSI web site (http://webstore.ansi.org/default.aspx)Lightning protectionsystemsRecommended Practices on SurgeVoltages in Low Voltage AC PowerCircuits, IEEE C62.41 (LatestEdition)IEEE web site (http://www.ieee.org/index.html)PowerDocument supportFor support in using this or any other Alcatel-Lucent document, contact Alcatel-Lucent atthe following telephone numbers.From United States•If you are using a landline, a cellular phone or VoIP, dial this number: 1-888-582-3688From other countries•If you are using a cellular phone or VoIP, dial this number: +1-630-224-2485•If you are using a landline (phone without a plus [+] character), replace the plus signwith your country's exit code. Dial this number: Exit code for the country of origin:1-630-224-2485. See the country-specific exit codes listed here.These numbers apply for document support only. Please see the section “Technicalsupport” for details about product hardware, software, and technical support.Technical supportFor technical support, contact your local Alcatel-Lucent customer support team. See theAlcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contactinformation.About this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction xixDRAFTDRAFT
How to orderTo order Alcatel-Lucent documents, contact your local sales representative or use OnlineCustomer Support (OLCS) (http://support.alcatel-lucent.com).How to commentNote to reviewers: The following "How to comment" text will appear in the finaldocument when it is published. However, the feedback method described below is for useonly on final documents. Please send your review comments to the author using theprocess you were given when you received this draft document.To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-lucent.com/comments/) or e-mail your comments to the Comments Hotline(comments@alcatel-lucent.com).About this document........................................................................................................................................................................................................................................................................................................................................................................................................................................................................xx Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
11Safety statementsOverviewPurposeThis chapter provides general information on the structure of safety instructions andsummarizes general safety requirements.General safety and residual riskThe equipment has been developed in line with state-of-the-art technology and conformswith current national and international safety requirements.The equipment is considered safe during normal operation when safe working practicesare complied with. However, hazards may arise if procedures are not followed correctlyor safe working practices are not complied with.ContentsStructure of safety statements 1-2Safety 1-4Safety - specific hazards 1-5Product safety 1-9...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 1-1DRAFTDRAFT
Structure of safety statementsOverviewThis topic describes the components of safety statements that appear in this document.General structureSafety statements include the following structural elements:Item Structure element Purpose1 Safety alert symbol Indicates the potential for personal injury(optional)2 Safety symbol Indicates hazard type (optional)3 Signal word Indicates the severity of the hazard4 Hazard type Describes the source of the risk of damage orinjury5 Safety message Consequences if protective measures fail6 Avoidance message Protective measures to take to avoid the hazard7 Identifier The reference ID of the safety statement(optional)SAMPLELifting this equipment by yourself can result in injurydue to the size and weight of the equipment.Always use three people or a lifting device to transportand position this equipment. [ABC123]CAUTIONLifting hazardSafety statements Structure of safety statements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................1-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Signal wordsThe signal words identify the hazard severity levels as follows:Signal word MeaningDANGER Indicates an extremely hazardous situation which, if not avoided, willresult in death or serious injury.WARNING Indicates a hazardous situation which, if not avoided, could result indeath or serious injury.CAUTION Indicates a hazardous situation which, if not avoided, could result inminor or moderate injury.NOTICE Indicates a hazardous situation not related to personal injury.Safety statements Structure of safety statements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 1-3DRAFTDRAFT
SafetyGeneral precautions for installation proceduresWARNINGFailure to observe these safety precautions may result in personalinjury or damage to equipment.•Read and understand all instructions.•Follow all warnings and instructions marked on this product.•Installation and maintenance procedures must be followed and performed bytrained personnel only.•The equipment must be provided with a readily accessible disconnect deviceas part of site preparation.•Grounding and circuit continuity is vital for safe operation of the equipment.Never operate the equipment with grounding/bonding conductordisconnected.•Before servicing, disconnect power input to reduce the risk of energyhazards.•If installed in ambient temperatures above 46°C (115°F), this unit must beinstalled only in restricted access locations, where access is limited toqualified service personnel only.Safety statements Safety........................................................................................................................................................................................................................................................................................................................................................................................................................................................................1-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Safety - specific hazardsDangerDANGERElectric-shock hazardWorking in severe weather can result in personal injury or death and damage to theequipment.Never install or perform maintenance during severe weather (high winds, lightning,blizzards, hurricane etc.).DANGERNoxious-substance hazardUse of unspecified cleaning agents can result in personal injury.Use only specified cleaning agents. Never use flammable solvents.Always ensure there is adequate ventilation in the work area and wear the appropriatepersonal protective equipment.WarningWARNINGLaser hazardUse of controls or adjustments or performance of procedures other than those specifiedherein may result in hazardous laser radiation exposure.Do not view directly into the laser beam with optical instruments such as a fibermicroscope because viewing of laser emission in excess of Class 1 limits significantlyincreases the risk of eye damage.Never look into the end of an exposed fiber or an open connector as long as the opticalsource is switched on.Ensure that the optical source is switched off before disconnecting optical fiberconnectors.Safety statements Safety - specific hazards........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 1-5DRAFTDRAFT
WARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.CautionCAUTIONRF hazardRF exposure in excess of applicable limits can result in adverse health effects.Metro Cells are designed and installed in order to comply with the international exposureguidelines laid down by the International Commission on Non-Ionizing RadiationProtection (ICNIRP) and/or the Institute of Electrical & Electronics Engineers(IEEE) C95.1. ICNIRP guidelines have been implemented by the European Commissionand a number of other countries. IEEE guidelines have been implemented in NorthAmerica and some other countries.Workers that are required to work in close proximity to the equipment, for examplemaintenance personnel, should strictly follow instructions provided by their employer.Workers equipped with personal medical electronic devices, such as pacemakers andhearing aids, shall consult the manufacturer's instructions and consult their occupationalhealth practitioner.CAUTIONElectrical energy hazardSome parts of all electrical installations are energized. Failure to observe this fact andthe safety warnings may lead to bodily injury and property damage.For this reason, only trained and qualified personnel (electrical workers as defined inIEC 60215 + A1 or EN 60215) may install or service the installation.Safety statements Safety - specific hazards........................................................................................................................................................................................................................................................................................................................................................................................................................................................................1-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
CAUTIONElectrical energy hazardThe power supply lines to the network element are energized. Contact with parts carryingvoltage can cause health problems, possibly including death, even hours after the event.Open and lockout the load disconnect switch in the distribution box to completelyde-energize the network element.NoticesNOTICEESD hazardSemiconductor devices can be damaged by electrostatic discharges (ESD)The following rules must be complied with when handling any module containingsemiconductor components:•Wear conductive or antistatic working clothes (for example, coat made of 100%cotton).•Wear a grounded wrist strap.•Wear shoes with conductive soles on a conductive floor surface or conductive workmat.•Leave the modules in their original packaging until ready for use.•Make sure there is no difference in potential between yourself, the workplace, and thepackaging before removing, unpacking, or packing a module.•Whenever handling ESD-sensitive components, do not touch any connection pins ortracks.•Place modules removed from the equipment on a conductive surface.•Test or handle the module only with grounded tools on grounded equipment.•Handle defective modules exactly like new ones to avoid causing further damage.NOTICECondensationSudden changes in the weather may lead to the formation of condensation oncomponents. Operating the unit when condensation moisture is present can destroy theunit.Units which show signs of condensation must be dried before installation.Safety statements Safety - specific hazards........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 1-7DRAFTDRAFT
NOTICEToolsTools left in the working area can cause short circuits during operation which can lead tothe destruction of units.Make sure after finishing your work that no tools, testing equipment, flashlights, etc.,have been left in or on the equipment.Safety statements Safety - specific hazards........................................................................................................................................................................................................................................................................................................................................................................................................................................................................1-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Product safetyEquipment safetySafety information for this equipment can be found on various Caution, Warning, Danger,information labels or instructions affixed to or included with the product or includedwithin this document. Informational and cautionary labels may appear near the item theyaddress or may be grouped in a single location on the equipment. Warnings are typicallyadjacent to the hazard that is noted on the label. The instructions, cautions and warningsfound on these labels must be understood and observed by all personnel involved with theequipment installation and maintenance.Safety statements Product safety........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 1-9DRAFTDRAFT
Safety statements Product safety........................................................................................................................................................................................................................................................................................................................................................................................................................................................................1-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
22Product overviewOverviewPurposeThis chapter provides an overview of Alcatel-Lucent 9764 Metro Cell Outdoor LTE2x1W and Alcatel-Lucent 9764 Metro Cell Outdoor LTE 2x2W products.ContentsFunctional description 2-2Physical description 2-4Supported installation options 2-13Hardware and ancillary items 2-17...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-1DRAFTDRAFT
Functional descriptionGeneral descriptionAlcatel-Lucent Metro Cells enable mobile service providers (MSPs) to delivercost-effective capacity to urban spots, as well as affordable coverage to rural locations.They also enhance the quality of experience (QoE) for end users by enabling faster, morereliable data connections and higher data throughput on 4G networks.The 9764 MCO LTE 2x1W and 9764 MCO LTE 2x2W products specified here aretargeted for high user density locations where additional capacity is required or even inareas where cell phone coverage is needed on short notice. The product can be deployedby mobile operators to provide a transparent outdoor capacity layer to complement themacro cell “umbrella” coverage layer.Product features and capabilitiesThe product features and capabilities in this release are:•Supports LTE FDD•Single LTE carrier•Supports either B25 band, B2 band, B3 band or B7 band•PCS 1900 MHz frequency band (B25 and B2)•DCS 1800 MHz frequency band (B3)•2600 MHz frequency band (B7)•9764 MCO LTE 2x1W supports the following RF antenna capabilities:– Transmit power: 1W at each internal RF antenna connector, and a guaranteedEquivalent Isotropically Radiated Power (EIRP) of 37 dBm per path for the B2MCO, B2/B25 (combined) MCO, B3 MCO, and B25 MCO, and 40 dBm per pathfor the B7 MCO. Transmit power can be reduced by a maximum of 14 dB toadjust the static cell power.– Integrated directional “Cube-based” antennas– Standard 2x2 MIMO configurations, 2 transmit and 2 receive diversity•The 9764 MCO LTE 2x2W supports the following RF antenna capabilities:– Supports two external antenna connectors (QN-type) allowing an internal RFantenna configuration or an external RF antenna configuration. The operator mustobtain the external RF antennas from third party vendors.– Transmit power of 2W at each external connector.•Receiver sensitivity optimized to permit near far simultaneous operation (referencesensitivity:-98 dBm)•Supports Plug and Play to automatically connect to the network.Product overview Functional description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
•The 9764 Metro Dock supports Gigabit Ethernet backhaul (support for other backhaulvariations are planned for the future).•Supports optional modular and field replaceable Wi-Fi Access Points.Refer to Alcatel-Lucent Small Cell Wi-Fi AP Technical Description,3MN-01840-0004-DEZZA for Wi-Fi AP product details.•The 9764 MCO LTE products have feature parity with some but not all macroeNodeB features. See the release-specific version of the Alcatel-Lucent LTE eNodeBMacro and Metro Products FDD Release Notes for more information. Refer to the“Related Information” block in “About this document” for the applicable documentversions.•Supported user capacity - refer to the table below.The number of active users and the number of Voice over LTE (VoLTE) calls supported isshown in the table below for the 9764 MCO LTE 2x1W and 9764 MCO LTE 2x2Wmodels.9764 MCO LTE2x1W modelSupportedBandwidth# active users supported # VoLTE callssupportedB25 5 MHz up to 64 active users with upto eight bearers per UEup to 32 VoLTE callsB2/B25 (combined) 10 MHz up to 64 active users with upto eight bearers per UEup to 64 VoLTE callsB2 (see note 2) 5 MHz up to 64 active users with upto eight bearers per UEup to 64 VoLTE callsB3 10 MHz up to 64 active users with upto eight bearers per UEup to 32 VoLTE callsB7 10 MHz up to 64 active users with upto eight bearers per UEup to 32 VoLTE callsB7 20 MHz up to 16 active users with upto eight bearers per UEup to 32 VoLTE callsNotes:1. The 9764 MCO LTE 2x1W and the 9764 MCO LTE 2x2W are hardware ready for 200simultaneous active users.2. The B2 capacity figures above apply to both the 9764 MCO V1.1 B2 LTE 2x1W and the9764 MCO V1.1 B2 LTE 2x2W models.3. In this release, the number of active users is the same as the number of RRC connectedusers.Product overview Functional description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-3DRAFTDRAFT
Physical descriptionProduct overviewThe Alcatel-Lucent 9764 Metro Cell Outdoor LTE 2x1W and Alcatel-Lucent 9764 MetroCell Outdoor LTE 2x2W are housed in an Alcatel-Lucent generic metallic case. Theproducts are designed to be deployed close to the users, usually in streets, on light polesor on walls of buildings, with a vertical profile that hides cable connectors and mountingkit for a smooth integration into the surrounding environment.The Alcatel-Lucent 9764 Metro Cell Outdoor LTE 2x1W and Alcatel-Lucent 9764 MCOLTE 2x2W products are shown in the following figure.Figure 2-1 9764 Metro Dock and 9764 MCO LTE 2x1W and Alcatel-Lucent 9764Metro Cell Outdoor LTE 2x2W9764 Metro Dock9764 Metro Dock9764 MCO LTE 2x1W moduleand9764 MCO LTE 2x2W module(reverse view)Top viewBottom viewProduct overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
In order to simplify configurations the backhaul access function and the radio partfunctions are separated, with a common interface as defined:Unit Function Description9764 Metro DockmoduleBackhaul access function Supports backhaul optionsHolds the 9764 MCO LTE module in place9764 MCO LTEmoduleRadio and basebandfunctionRadio functionsDigital processing functionsPower supply functions9764 MCO Wi-FiAP moduleWi-Fi function Wi-Fi network access function.Refer to Alcatel-Lucent Small Cell Wi-Fi APTechnical Description, 3MN-01840-0004-DEZZA for Wi-Fi AP product details.Weights and dimensionsThe physical dimensions of the Alcatel-Lucent 9764 Metro Cell Outdoor are:Dimensions (9764 MCO LTE module+ 9764 Metro Dock) (Length x Widthx Depth)501 x 170 x 164 mm (19.7 x 7.0 x 6.5 in)Dimensions (9764 MCO module +9764 Metro Dock + 9764 MCOWi-Fi AP) (Length x Width x Depth)With 9764 MCO Wi-Fi AP V1.0 MG: 550 x 170 x 150mm (21.7 x 6.7 x 5.9 in)With 9764 MCO Wi-Fi AP V1.0 HG: 590 x 170 x 150mm (23.2 x 6.7 x 5.9 in)Figure 2-2 9764 MCO LTE with 9764 MCO Wi-Fi APWi-FiAP9764 Wi-Fi AP 9764 MCO front viewwith 9764 Wi-Fi AP9764 MCO rear viewwith 9764 Wi-Fi APProduct overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-5DRAFTDRAFT
Volume (9764 MCO LTE module +9764 Metro Dock)12.7 L (3.35 gal)Weight (9764 MCO LTE module +9764 Metro Dock)10.1 kg (22.2 lb)Weight (9764 MCO LTE module +9764 Metro Dock + 9764 MCOWi-Fi AP)With 9764 MCO Wi-Fi AP V1.0 MG: 10.57 kg (23.30lb)With 9764 MCO Wi-Fi AP V1.0 HG: 10.77 kg (23.74lb)Weight (9764 MCO LTE moduleonly)9.1 kg (20.1 lb)Dimensions for optional pair-mount configurationThe physical dimensions when two 9764 MCOs are pair-mounted are as follows:Configuration Height Width Depth4G MCO + 3G MCOWith Wi-Fi AP, Minimaldistance between MCOs,With full tilt mechanics590 mm 410 mm includingback-bracket(338 mm withoutback-bracket)290 mm4G MCO + 3G MCO NOWi-Fi AP, Minimaldistance between MCOs,NO tilt mechanics501 mm 410 mm includingback-bracket(338 mm withoutback-bracket)210 mmAlcatel-Lucent 9764 Metro Cell Outdoor LTE overviewThe 9764 MCO LTE module is made up of three main units which are responsible forradio, digital processing and power supply functions.Product overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Unit Function9764 MCO LTE module Digital part:•Gigabit Ethernet switch•Processors to provide modem and controller functionality•9764 Metro Dock interface (data, control and power supply)•9764 MCO Wi-Fi AP interfaceRadio part•Radio part B25:– LTE Band 25 (1850 MHz - 1915 MHz (UL), 1930 MHz - 1995MHz (DL))– Two TX antenna connectors and two RX antenna connectors•Radio part 9764 MCO V1.1 B2 LTE 2x1W:– LTE Band 2 (1850 MHz - 1910 MHz (UL), 1930 MHz - 1990MHz (DL))– Two TX antenna connectors and two RX antenna connectors•Radio part 9764 MCO V1.1 B2 LTE 2x2W:– LTE Band 2 (1850 MHz - 1910 MHz (UL), 1930 MHz - 1990MHz (DL))– Two external RF antenna connectors (Type QN)•Radio part B2/B25 (combined):– LTE Band 25 (1850 MHz - 1915 MHz (UL), 1930 MHz - 1995MHz (DL))– Two TX antenna connectors and two RX antenna connectors•Radio part B3:– LTE Band 3 (1710 MHz - 1785 MHz (UL), 1805 MHz - 1880MHz (DL))– Two TX antenna connectors and two RX antenna connectors•Radio part B7:– LTE Band 7 (2500 MHz - 2570 MHz (UL), 2620 MHz - 2690MHz (DL))– Two TX antenna connectors and two RX antenna connectors9764 MCO LTE 2x1W models: Internal GPS antenna connector(depending on the model) or an external GPS connector for localizationsynchronization (only one can be used)9764 MCO LTE 2x2W models: A GPS connector that is switchablebetween internal GPS antenna and external GPS antenna.Power supply part - please see “Power supply” (p. 2-10) for internalpower module unit information.9764 MCO LTE 2x1W Antennas •Integrated cube-based RF antennas configured for 2x2 MIMO.•internal GPS antenna configuration (depending on the model) orexternal GPS antenna configuration.Product overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-7DRAFTDRAFT
Unit Function9764 MCO LTE 2x2W Antennas •Integrated 1-element RF antenna or cabling to external remote RFantennas.•Internal GPS antenna configuration or external GPS antennaconfiguration.Power source •AC power supply or DC power supply (see “Power supply”(p. 2-10) for further information)9764 MCO LTE module connection interfacesThe following figure shows the connection interfaces for the 9764 MCO LTE module.Figure 2-3 9764 MCO LTE module connection interfaces (1 of 2)Power connectorBlind mate connectorbetween Metro Cell Moduleand the Metro DockWi-Fi AP connector(for optional Wi-Fi AP)Cable gland9764 MCO LTE2x1W module9764 Metro DockmoduleGPS connector(for optional externalGPS antenna)Product overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Figure 2-3 9764 MCO LTE module connection interfaces (2 of 2)External GPSantenna connectorPower connectorBlind mate connectorbetween Metro Cell Moduleand the Metro DockCable gland9764 MCO B2 2x2WLTE module9764 Metro DockmoduleExternal antenna connectors(with antennas attached)WIFI AP connector(optional)Figure 2-4 9764 MCO LTE module connection interfaces - double lug ground pointdetailDouble lugground pointProduct overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-9DRAFTDRAFT
Connection location Description9764 MCO LTE module (back) A power supply connectorA blind mate connector for connecting the 9764 MCO LTEmodule and the 9764 Metro Dock9764 MCO Wi-Fi AP (optional) connectorExternal GPS antenna connectorInternal GPS antenna connector (only 2x1W modelssupporting an internal GPS configuration)Power supplyThe 9764 MCO LTE module supports the following power source variants:•AC power feed in the 100 V – 240 V AC range, ~2.0 A 50-60 Hz, with nominalvoltages of 110 V and 230 V.The AC power is surge-protected as follows:– First level (no damage to equipment, no service interruption): 2 KV/1 KA•DC power feed of -48 V, 3.5 A SELV Source.Surge requirements satisfy GR-1089-CORE and IEC 61000-4-5, providing 6 KV (3KA)surge protection.Grounding connection points, located below the power connector on the chassis, providegrounding for the power module.A power module unit inside the 9764 MCO LTE 2x1W and Alcatel-Lucent 9764 MCOLTE 2x2W provides AC/DC conversion (5.3 V output) to its power board, which thenprovides secondary DC-DC conversion and distributes 5.3 V to the 9764 Metro Dockmodule and the 9764 MCO Wi-Fi AP module (if equipped).The power module supports an average consumption of 100 W, as well as the peak 130 Wconsumption projected for the 9764 MCO LTE 2x1W and 9764 MCO LTE 2x2W (9764MCO LTE module, 9764 Metro Dock module, and optional 9764 MCO Wi-Fi APmodule). Without the optional 9764 MCO Wi-Fi AP module, average consumption isapproximately 92 W (peak 120 W).RF antennaThe 9764 MCO LTE 2x1W support an integrated RF antenna configured for 2x2 MIMO.Product overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
The 9764 MCO V1.1 B2 LTE 2x2W supports two external antenna connectors (Type QN)allowing the following RF antenna configurations:•Internal 1-element RF antenna•Cabling to external remote RF antennas. The external antennas are provided bythird-party vendors selected by the operator.GPS antennaThe 9764 MCO LTE 2x1W supports the following GPS antenna configurations:•internal GPS antenna mounted behind the radome to provide localizationsynchronization of the unit, or•an external GPS antenna connector (QMA) on the 9764 MCO LTE module, whichcan be used to connect to an external GPS antenna•The 9764 MCO LTE 2x1W will be installed to use either the internal GPS antenna (ifavailable for that model) or it will be connected to an external GPS antenna. Whenconfigured to use the internal GPS antenna, a bridge cable is used to connect theexternal GPS QMA connector to the internal GPS QMA connector.A QMA GPS Antenna switch is available on the 9764 MCO V1.1 B2 LTE 2x2W model,which allows it to support both internal GPS antenna and external GPS antenna solutionswithout the use of a bridge cable. When no external GPS cable is attached to the QMAconnector, the internal GPS antenna is engaged and active. When an external GPSantenna cable is attached to the QMA connector, a switch in the connector automaticallysets the 9764 MCO V1.1 B2 LTE 2x2W up for the external GPS antenna configuration.When the external GPS antenna cable is removed, the switch in the QMA connectormoves the 9764 MCO V1.1 B2 LTE 2x2W back to an internal GPS antennaconfiguration.Table 2-1 GPS antenna optionsMetro Cell model Internal GPS antenna External GPS antenna9764 MCO V1.0 B25 LTE 2x1W X9764 MCO V1.1 B2 LTE 2x1W X9764 MCO V1.1 B3 LTE 2x1W X X9764 MCO V1.1 B7 LTE 2x1W X9764 MCO V1.1 B2/B25 LTE2x1WXX9764 MCO V1.1 B2 LTE 2x2W X XProduct overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-11DRAFTDRAFT
Status indicatorThe 9764 MCO LTE supports a single bi-color LED (red/green) which is located on therear lower portion of the 9764 MCO LTE module. The LED is not intended for use duringnormal operation of the equipment; however, it can provide a visual status of theequipment during initial installation and commissioning.Product labellingThe 9764 MCO LTE module has the following labelling:1. A product label reflecting:•Vendor name/Icon•Model name•Part number•Serial number•Data matrix barcode for Part number and Serial number•CLEI code•MAC address2. A regulatory label reflecting:•Vendor name/Icon•Product name•Regulatory rules•Power input•Enclosure rating•Applicable regulatory and environmental certification logos•Manufacturer name3. An FCC label reflecting (for B2, B25 and B2/B25 (combined) MCOs only):•Vendor name/Icon•FCC IDProduct overview Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-12 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Supported installation optionsOverviewThe following section describes the supported installation options for the Alcatel-Lucent9764 Metro Cell Outdoor LTE 2x1W and Alcatel-Lucent 9764 Metro Cell Outdoor V1.1B2 LTE 2x2W products. These include:•Standard installation options for all 9764 MCO LTE 2x1W products.•Standard installation options for all 9764 MCO LTE 2x2W products.•Daisy chain installation options where two 9764 MCO modules are daisy chainedtogether and share the same backhaul port.•Pair-mount installation options where:– a 9764 MCO V1.1 B2 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W, or– a 9764 MCO V1.1 B2 LTE 2x2W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W, or– a 9764 MCO V1.1 B7 LTE 2x1W product is mounted with a 9764 MCO V1.0 B1WCDMA 1W.– a 9764 MCO V1.1 B2/B25 LTE 2x1W product is mounted with a 9764 MCOV1.0 B1 WCDMA 1W.Standard installation optionsAlcatel-Lucent 9764 MCO LTE 2x1W and Alcatel-Lucent 9764 MCO LTE 2x2Wproducts are designed to be deployed outdoors and close to the users, usually on lightpoles or lamp posts in streets or on building walls, with a vertical profile. Optional tiltmounting brackets can be used that allow the 9764 MCO module to be adjusted invertical and/or horizontal direction at same time.Figure 2-5 Installation examplesPole mount installation Wall mount installationProduct overview Supported installation options........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-13DRAFTDRAFT
In addition, Alcatel-Lucent 9764 MCO LTE 2x1W and Alcatel-Lucent 9764 MCO LTE2x2W products can be fitted with an optional 9764 MCO Wi-Fi AP module as shown inthe following figure.Ethernet daisy chain installation optionsIn a daisy chain installation configuration two Alcatel-Lucent 9764 MCOs can be daisychained together, where they share the same backhaul port, thus reducing the investmentcost needed to connect the 9764 MCOs to the backhaul network and aggregating theuplink and downlink traffic. Daisy chained 9764 MCOs may be co-located or separatedby some distance.Figure 2-6 9764 MCO Wi-Fi AP module attached to 9764 MCO LTE module (frontview)Wi-Fi APProduct overview Supported installation options........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-14 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Daisy chain configuration options are described in, “Pair mount and daisy chainrequirements” (p. 3-13)Pair-mount installation optionsIn a “pair-mount” installation configuration a 9764 MCO LTE 2x1W product or a 9764MCO LTE 2x2W product can be mounted with a 9764 MCO WCDMA product to form aMulti-Standard Pair configuration. The supported pair-mount configurations are asfollows:•A 9764 MCO V1.1 B2 LTE 2x1W in a pair-mount configuration with a 9764 MCOV1.0 B2 WCDMA 1W.•A 9764 MCO V1.1 B2/B25 LTE 2x1W in a pair-mount configuration with a 9764MCO V1.0 B2 WCDMA 1W.•A 9764 MCO V1.1 B2 LTE 2x2W in a pair-mount configuration with a 9764 MCOV1.0 B2 WCDMA 1W,•A 9764 MCO V1.1 B7 LTE 2x1W in a pair-mount configuration with a 9764 MCOV1.0 B1 WCDMA 1W.Note: This 9764 MCO V1.1 B7 LTE 2x1W/9764 MCO V1.0 B1 WCDMA 1Wpair-mount configuration applies to AC variants only.Service providers can deploy these configurations on the same site to meet the growingdemands of capacity on the 3G and 4G technologies.Figure 2-7 9764 MCO daisy chain installation exampleBackhaulProduct overview Supported installation options........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-15DRAFTDRAFT
pair-mount configuration options are described in, “Pair mount and daisy chainrequirements” (p. 3-13)Figure 2-8 9764 MCO pair-mount installation exampleProduct overview Supported installation options........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-16 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Hardware and ancillary itemsOverviewThe following section lists the Alcatel-Lucent 9764 Metro Cell Outdoor base hardwareequipment, the installation kits and ancillary items that can be ordered fromAlcatel-Lucent.9764 MCO base itemsThe Alcatel-Lucent 9764 MCO LTE 2x1W or the Alcatel-Lucent 9764 MCO LTE 2x2Wpackaging contains the following base items:•9764 MCO LTE 2x1W module or•9764 MCO LTE 2x2W module9764 Metro Dock base itemsThe Alcatel-Lucent 9764 Metro Dock packaging contains the following base items:•Alcatel-Lucent 9764 Metro Dock (including lock and key)9764 MCO Wi-Fi AP base itemsThe Alcatel-Lucent 9764 Metro Cell Outdoor Wi-Fi AP is an optional product. Twomodels are available:•9764 MCO Wi-Fi AP v1.0 MG model (medium-gain antenna)•9764 MCO Wi-Fi AP v1.0 HG model (high-gain antenna)Ancillary itemsThe following tables list the ancillary items that are available for order fromAlcatel-Lucent in support of the defined equipment installation and configuration options.Installation kitsThe following table list the installation kits that are available for order fromAlcatel-Lucent in support of the equipment installation options.Installation kit Description UseBanding kit Stainless steel bandsBand buckles (Ear-Lokt)Mandatory:•pole mount onlyBanding tool Standard BAND-IT®Banding Tool(CR00169), including operatinginstructionsMandatory:•use with the Banding kit for polemount onlyWall spacer kit 9764 Metro Dock wall spacer Mandatory:•wall mount without tiltProduct overview Hardware and ancillary items........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-17DRAFTDRAFT
Installation kit Description UseVertical tilt installation kit Vertical tilt bracket Mandatory:•pole mount with tilt•wall mount: with vertical only•wall mount: with vertical andhorizontal tiltHorizontal tilt installation kit Horizontal tilt bracket Mandatory:•wall mount: with horizontal tilt only•wall mount: with horizontal andvertical tiltPowerItem Description UsePower connector (AC) AC power connector Required for 9764 MCO module with ACpower (International markets)Power connector (DC) DC power connector Required for 9764 MCO module with DCpower (International markets)Power cable Power cable IN/OUT 3G1,5mm²,100m roll or multiples of 1m length(as needed)Required for 9764 MCO module(International markets)Power cable (AC) Power cable pre-assembled with ACpower connector, various lengths(2m. 4.5m, 9m, 12m)Required for 9764 MCO module with ACpower (North America Regional markets)Power cable (DC) Power cable pre-assembled with DCpower connector, various lengths(2m. 4.5m, 9m, 12m)Required for 9764 MCO module with DCpower (North America Regional markets)GroundingItem Description UseGround cable Ground cable,Y/G 10mm² in 100mrollRequired for International marketsGround cable Ground cable, 8 AWG Required for North America RegionalmarketsSFP modulesItem Description UseSFP module SFP GBE 10/100/1000BaseT (copper) OptionalElectrical backhaul onlySFP module SFP GBE 1000BaseLX (Single mode) OptionalOptical backhaul, Daisy chainingProduct overview Hardware and ancillary items........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-18 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Item Description UseSFP module SFP GBE 1000BaseLX / CPRI (Single mode) OptionalOptical backhaul, Daisy chaining,Pair-mount configurationSFP module SFP GBE 1000BaseSX / CPRI (Multi mode) OptionalOptical backhaul, Daisy chaining,Pair-mount configurationSurge arrestorItem Description UseInternal surge arrestor19764 Metro Dock internal Ethernetsurge arrestor kitOptionalHighly recommended if GBE 1000BaseTbackhaul connection is providedExternal surge arrestor External Ethernet surge arrestor kit,including:•mounting bracket•pole bands and buckle•Ethernet cable, 0.6 m (2 ft)OptionalHighly recommended if GBE 1000BaseTbackhaul connection is providedNotes:1. The 9764 Metro Dock internal Ethernet surge arrestor is available within Release LR14.1.L.Ethernet cable - ElectricalItem Description UseElectrical Ethernet cable 2 meter outdoor, 4 pairs, 2 RJ45 (plus1 spare)OptionalUse with SFP GBE 10/100/1000BaseTElectrical Ethernet cable 25 meter outdoor, 4 pairs, 2 RJ45(plus 1 spare)OptionalUse with SFP GBE 10/100/1000BaseTElectrical Ethernet cable 100 meter outdoor, 4 pairs, 2 RJ45(plus 1 spare)OptionalUse with SFP GBE 10/100/1000BaseTEthernet cable - OpticalItem Description UseFiber Optic cable SMDF LC-LC 2SM 5mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 15mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Product overview Hardware and ancillary items........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-19DRAFTDRAFT
Item Description UseFiber Optic cable SMDF LC-LC 2SM 30mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 50mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 70mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 85mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 100mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 150mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 200mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 250mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable SMDF LC-LC 2SM 300mSingle mode fiber duplex 250 mmBreakout on both sidesOptionalUse with SFP GBE 1000BaseLX (Singlemode)Fiber Optic cable MM LC-LC 2MM 5mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 15mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 30mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 50mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 70mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Product overview Hardware and ancillary items........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-20 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Item Description UseFiber Optic cable MM LC-LC 2MM 85mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 100mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 150mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 200mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 250mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)Fiber Optic cable MM LC-LC 2MM 300mMulti mode fiber duplex, 250 mmBreakout on both sidesOptionalSFP GBE 1000BaseSX (Multi mode)External antenna - GPSItem Description UseGPS antenna External GPS Antenna, 1575MHz*26 dBiUsed if MCO is configured for externalGPS antenna and cable loss <10dBi @1575MHzGPS antenna External GPS Antenna, 1575MHz*40 dBiUsed if MCO is configured for externalGPS antenna and cable loss >10dBi @1575MHzJumper cable External GPS Antenna jumper cable(various lengths)Mandatory1 cable per MCO if external GPS antennais usedAdapter cable External GPS Antenna adaptor cablefrom the ancillaryMandatory1 cable per MCO if external GPS antennais usedWeatherproof tape For B25 MCO, B2 MCO and B2/B25MCO - one layer of weatherprooftape applied to the cable connections.For B3 MCO and B7 MCO, thefollowing two types of weatherprooftape must be applied to the cableconnections: first the linerless rubbersplicing tape and then the vinylelectrical tape (vinyl tape over rubbertape).MandatoryProduct overview Hardware and ancillary items........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 2-21DRAFTDRAFT
Note: The internal GPS antenna solution is not supported on the 9764 MCO V1.1 B7LTE 2x1W, 9764 MCO V1.1 B2 LTE 2x1W and 9764 MCO V1.0 B25 LTE 2x1Wmodels.External RF antennasThe 9764 MCO V1.1 B2 LTE 2x2W module has two external RF antenna ports for theconnection to third party supplied antennas.For the RF antenna specifications refer to the RF antenna part of the System architecturesection of the 9YZ-04152-0056-DEZZA - Alcatel-Lucent 9764 Metro Cell Outdoor LTE2x1W and 2x2W Technical Description document.Pair-mount configurationItem Description Use9764 Metro Dock doublesupport plateSupport plate for mounting 9764MCO in a pair-mount configurationUse in a 9764 MCO pair-mountconfigurationExtension plate Alignment Plate for 3G 9764 MCO ina pair-mount configurationUse in a 9764 MCO pair-mountconfigurationProduct overview Hardware and ancillary items........................................................................................................................................................................................................................................................................................................................................................................................................................................................................2-22 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
33Installation of the 9764Metro DockOverviewPurposeThis chapter provides the information and procedures for mounting the 9764 Metro Dockonto a pole or wall, with or without the optional tilt mechanism.Contents9764 Metro Dock pre-installation 3-29764 Metro Dock Pre-installation information 3-3Pole mount installation requirements 3-5Wall mount installation requirements 3-9Pair mount and daisy chain requirements 3-139764 Metro Dock installation 3-18Procedure 3-1: Pole mount the 9764 Metro Dock 3-19Procedure 3-2: Pole mount the 9764 Metro Dock using optional tilt brackets 3-25Procedure 3-3: Wall mount the 9764 Metro Dock 3-35Procedure 3-4: Wall mount the 9764 Metro Dock using optional tilt brackets 3-40Procedure 3-5: Pole mount the 9764 Metro Dock in a pair configuration 3-54Procedure 3-6: Wall mount the 9764 Metro Dock in a pair configuration 3-719764 Metro Dock cabling 3-89Procedure 3-7: 9764 Metro Dock ground cabling 3-90Procedure 3-8: 9764 Metro Dock Ethernet cabling - fiber optic 3-92Procedure 3-9: 9764 Metro Dock Ethernet cabling - electrical 3-999764 Metro Dock post-installation 3-111Procedure 3-10: Final installation activities and checks 3-112...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-1DRAFTDRAFT
9764 Metro Dock pre-installationOverviewPurposeThis section provides pre-installation information as well as listing tools and materialsrequired for Alcatel-Lucent 9764 Metro Dock mounting.Contents9764 Metro Dock Pre-installation information 3-3Pole mount installation requirements 3-5Wall mount installation requirements 3-9Pair mount and daisy chain requirements 3-13Installation of the 9764 Metro Dock9764 Metro Dock pre-installationOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
9764 Metro Dock Pre-installation informationVerify site preparationThe following site preparation requirements should be checked and met before theinstallation of the equipment can begin. If some of the requirements are not met, theinstaller must do so now:•Ensure equipment is planned to be installed as high as possible to avoid obstructions•Consider nearby sources of interference. Also check possibility of future obstructionssuch as plans to erect buildings and trees that may grow tall enough to obstruct thewireless path•Ensure adequate clearance is provided for service access•Ground, power and backhaul cabling has been routed and is in place•Ensure any site specific fixing materials (screws, washers, wall plugs) for pole/wallmounting the equipment are available.Product delivery contentsUnpack and examine the product packaging contents. If you notice any damage, ormissing items as listed in the Packing List, immediately notify the carrier that deliveredthe unit and contact your Alcatel-Lucent representative.The Alcatel-Lucent 9764 Metro Dock product packaging contains the following items:•The 9764 Metro Dock module (including lock and key)Installation kitsIn addition to the standard product deliverable ensure the appropriate installation kits andancillary items are available to support the product mounting options.Installation Kits Pole mount Wall mountNo tilt With tilt No tilt Vertical tiltonlyHorizontaltilt onlyCombinedhoriz./vert. tiltBanding kit Yes YesBanding tool Yes YesVertical tilt kit Yes Yes YesHorizontal tilt kit Yes YesWall spacer kit YesBasic kit Yes Yes Yes Yes Yes YesInstallation of the 9764 Metro Dock9764 Metro Dock pre-installation9764 Metro Dock Pre-installation information........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-3DRAFTDRAFT
Tools required for installationThe following tools may be used during installation:•Drill (pneumatic hammer) and assorted drill bits•Pliers•Adjustable spanners•M17 socket wrench•Screwdrivers (power and/or manual):– Phillips (flat blade)– Torx (T-25 and T-40)•HRS (Hirose) HT206/TM21p-88p crimping tool (for RJ45 cable)•Data cable tester for shielded RJ45 (optional)•Measuring tape•Digital compass (to aid establishing product orientation)•Marker, to mark wall mounting holes•Vacuum cleaner or equivalent (required for clearing debris from wall mounting holes)•Spirit level•Hammer•PIB (self-amalgamating) tape and 3M Super 33+ vinyl tape•Ear protectors and safety goggles/glasses•Assorted cable ties (various lengths)•Heavy duty tape•Adjustable strapsInstallation of the 9764 Metro Dock9764 Metro Dock pre-installation9764 Metro Dock Pre-installation information........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Pole mount installation requirementsPurposeThis topic outlines the basic requirements, installation kits and recommended anchormaterials when mounting the Alcatel-Lucent 9764 Metro Dock directly onto a pole, ontotilt brackets or onto a pair-mount bracket.Pole mount optionsThe 9764 Metro Dock is less than 1 kg (2.2 lbs) and can be easily mounted onto a pole(wooden or metal) for the following installation options:•9764 Metro Dock screwed onto a wooden pole (without the tilt option).Mounting screws and washers have to be locally supplied. Two M8x50 stainless steelhex head screws and two M8x16x1.6 plain washers are recommended.•9764 Metro Dock banded onto a wooden or metal pole (without the tilt option)The pole band installation kit is used.•9764 Metro Dock attached to the vertical tilt bracket. Vertical tilt bracket is eitherscrewed or banded onto a wooden or metal pole.•9764 Metro Dock pair (with or without tilt brackets) attached to a double Metro Docksupport plate. Double Metro Dock support plate is banded onto a wooden or metalpole.This deployment option is used when a 9764 MCO V1.1 LTE 2x1W or a 9764 MCOLTE 2x2W product is mounted with a 9764 MCO WCDMA 1W product to form aMulti-Standard Pair configuration.The available pair-mount installation options are:– a 9764 MCO V1.1 B2 LTE 2x1W product mounted with a 9764 MCO V1.0 B2WCDMA 1W product– a 9764 MCO V1.1 B2/B25 LTE 2x1W product with a 9764 MCO V1.0 B2WCDMA 1W product– a 9764 MCO V1.1 B7 LTE 2x1W product mounted with a 9764 MCO V1.0 B1WCDMA 1W product– a 9764 MCO V1.1 B2 LTE 2x2W product mounted with a 9764 MCO V1.0 B1WCDMA 1W product.Installation of the 9764 Metro Dock9764 Metro Dock pre-installationPole mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-5DRAFTDRAFT
Pole mount installation kits and bracketsThe following table provides the orderable installation kits and brackets that can be used,depending on the deployment scenario, for 9764 Metro Dock pole mounting.Table 3-1 Pole mount installation kits and bracketsItem DescriptionBanding kit Required when directly attaching the 9764 Metro Dock or vertical tiltbracket to a pole (diameter 50 to 300 mm) using stainless steel bands.Stainless steel bands and buckles (Ear-Lokt)Banding tool Standard BAND-IT®Banding Tool (CR00169), including operatinginstructionsRequired in order to tighten stainless steel metal bandsVertical tilt bracket Provides +/- 30° vertical tilt (up/down) adjustment1Double 9764 MCO support plate Double 9764 MCO support plate for pair-mount deployment optionDouble 9764 MCO extension plate Extension plate for 3G 9764 MCO and 4G 9764 MCO alignment in apair-mount deployment optionNotes:1. Due to the length of the 9764 MCO LTE module, thermal limitations dictate maximumadjustment of +/- 20° vertical tilt.The following figure shows the orderable brackets used for pole mount installation,depending on the deployment scenario.Figure 3-1 Pole mount banding and bracketsTilt bracket assembly(single Metro Dock) Tilt bracket assembly(double Metro Dock)Installation of the 9764 Metro Dock9764 Metro Dock pre-installationPole mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Recommended pole anchor materialsSurface structure Recommended anchor materials Recommended screw torqueWood Screw Hex T M8x50 stainless steel (x2)Washer plain M8x16x1.6 stainless steel (x2)7.0 N.m (62.0 lb.in).Pole mount installation examplesThe following figures show examples of 9764 Metro Dock pole mount installation, polemount installation using vertical tilt and pair-mount installation.Figure 3-2 9764 Metro Dock pole mount using screwsPole mount - with tiltPole mount - without tiltInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationPole mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-7DRAFTDRAFT
Figure 3-3 9764 Metro Dock pole mount using bandingPole mount - without tilt Pole mount - with tiltFigure 3-4 Double 9764 Metro Dock pole mountInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationPole mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Wall mount installation requirementsPurposeThis topic outlines basic requirements, installation kits and recommended anchormaterials when mounting the Alcatel-Lucent 9764 Metro Dock onto a solid concrete wallor flat surface, onto tilt brackets or onto a pair-mount bracket.Wall mount optionsThe 9764 Metro Dock weighs less than 1 kg (2.2 lbs) and can be easily mounted onto anyflat, sturdy wall for the following installation options:•9764 Metro Dock attached to directly to a wall or flat surface (using wall spacer)•9764 Metro Dock attached to the vertical/horizontal tilt bracket(s). Vertical/horizontaltilt bracket(s) are attached to a wall.•9764 Metro Dock pair (with or without tilt brackets) attached to a double Metro Docksupport plate. Double Metro Dock support plate is attached to a wall.This deployment option is used when a 9764 MCO V1.1 LTE 2x1W product or a9764 MCO LTE 2x2Wproduct is mounted with a 9764 MCO WCDMA 1W product toform a Multi-Standard Pair configuration.The available pair-mount installation options are: a 9764 MCO V1.1 B2 LTE 2x1Wproduct mounted with a 9764 MCO V1.0 B2 WCDMA 1W, a 9764 MCO V1.1 B7LTE 2x1W product mounted with a 9764 MCO V1.0 B1 WCDMA 1W product and a9764 MCO V1.1 B2 LTE 2x2W product mounted with a 9764 MCO V1.0 B1WCDMA 1W product.Wall mount installation brackets and kitsThe following table lists the orderable installation brackets that can be used, depending onthe deployment scenario, for 9764 Metro Dock wall mounting.Table 3-2 Wall mount installation bracketsItem DescriptionWall spacer Required when directly attaching the 9764 Metro Dock to a wall or flatsurface and no tilt device is used. The wall spacer keeps a sufficientdistance between the wall and 9764 Metro Dock for airflow purposes.Note: If vertical/horizontal tilt device is used, then the wall spacer is notrequired.Vertical tilt bracket1Provides +/- 30° vertical tilt (up/down) adjustmentNote: Can be used in combination with the horizontal installation kit toprovide:•+/- 30° vertical tilt (up/down) adjustment, and•+/-45° horizontal tilt (left/right) adjustmentInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationWall mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-9DRAFTDRAFT
Table 3-2 Wall mount installation brackets (continued)Item DescriptionHorizontal tilt bracket Provides +/-45° horizontal tilt (left/right) adjustmentNote: Can be used in combination with the vertical tilt installation kit toprovide:•+-45° horizontal tilt (left/right) adjustment, and•+/- 30° vertical tilt (up/down) adjustmentDouble 9764 MCO support plate Double 9764 MCO support plate for pair-mount deployment optionDouble 9764 MCO extension plate Extension plate for 3G 9764 MCO and 4G 9764 MCO alignment in apair-mount deployment optionNotes:1. Due to the length of the 9764 MCO LTE module, thermal limitations dictate maximumadjustment of +/- 20° vertical tilt.The following figure shows the orderable brackets used for wall mount installation,depending on the deployment scenario.Recommended wall anchor materialsSurface structure Recommended anchor materials Recommended screw torqueWood Screw Hex T M8x70 stainless steel (x3)Washer plain M8x16x1.6 stainless steel (x3)7.0 N.m (62.0 lb.in).Concrete Screw CHC M6x80 stainless steel (x3)Washer plain M6x12x1.6mm stainless steel (x3)Washer spring M6x12x1.2mm stainless steel (x3)Plug expansion Rawlnut M6x50 (x3)7.0 N.m (62.0 lb.in).Figure 3-5 Wall mount bracketsSpacer bracket(wall only)Vertical tilt bracket(wall/pole)Horizontal tilt bracket(wall only)Installation of the 9764 Metro Dock9764 Metro Dock pre-installationWall mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Wall mount installation examplesThe following figures show examples of 9764 Metro Dock wall mount installation, wallmount installation using horizontal/vertical tilt and pair-mount installation.Figure 3-6 9764 Metro Dock wall mount (no tilt)Figure 3-7 9764 Metro Dock wall mount (with tilt)Vertical tilt only Horizontal tilt only Horizontal/Vertical tiltcombinationInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationWall mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-11DRAFTDRAFT
Figure 3-8 Double 9764 Metro Dock wall mountInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationWall mount installation requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-12 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Pair mount and daisy chain requirementsOverviewTwo 9764 MCOs can be daisy chained together to share the same backhaul port, reducingthe investment cost needed to connect the 9764 MCOs to the backhaul network andaggregating the uplink traffic. Daisy chain connectivity scenarios support 9764 MCOsthat are co-located and connected together (for example, connectivity used for pair-mountconfigurations) or 9764 MCOs that are separated by some distance.Pair-mount configuration with daisy chainingA 9764 MCO LTE connected to the backhaul network plus a 9764 MCO WCDMAconnected to the daisy chain port of the 9764 MCO LTE that is connected to the backhaulnetwork.Pair-mount installation options that form a Multi-Standard Pair configuration are:•a 9764 MCO V1.1 B2 LTE 2x1W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,•a 9764 MCO V1.1 B2/B25 LTE 2x1W product with a 9764 MCO V1.0 B2 WCDMA1W product•a 9764 MCO V1.1 B2 LTE 2x2W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,•a 9764 MCO V1.1 B7 LTE 2x1W product is pair-mounted with a 9764 MCO V1.0 B1WCDMA 1W product.Installation of the 9764 Metro Dock9764 Metro Dock pre-installationPair mount and daisy chain requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-13DRAFTDRAFT
Note:•An optional Wi-Fi Access Point may be attached to the MCO that is connected tothe backhaul network.•To support Carrier Aggregation or Carrier Aggregation readiness the optical daisychain SFPs should a Single Mode GBE/CPRI SFP or a Multi Mode GBE/CPRISFP.Pair-mount configuration without daisy chainingA 9764 MCO LTE connected to the backhaul network plus a 9764 MCO WCDMAconnected to the backhaul network, with no daisy chaining.Pair-mount installation options that form a Multi-Standard Pair configuration are:•a 9764 MCO V1.1 B2 LTE 2x1W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,a 9764 MCO V1.1 B2/B25 LTE 2x1W product with a 9764 MCO V1.0 B2 WCDMA1W product•a 9764 MCO V1.1 B2 LTE 2x2W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,•a 9764 MCO V1.1 B7 LTE 2x1W product is pair-mounted with a 9764 MCO V1.0 B1WCDMA 1W product.BH13G WCDMA MCO (1W)BH2Optical 250 mm breakoutcable (SM or MM)BH14G LTE MCO (2x1W)Wi-Fi APElectrical cableorOptical 250 mm breakoutcable (SM or MM)Electrical SFPorOptical SFP(SMorMM)Optical SFP(SM or MM)BH2BackhaulMetro Dock double support plateInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationPair mount and daisy chain requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-14 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Note: An optional Wi-Fi Access Point may be attached to the MCO that is connectedto the backhaul network.Daisy chaining without pair-mount configurationA maximum of two 9764 MCO modules and a single Wi-Fi Access Point may be daisychained together.The 9764 MCO LTE supports the following daisy chain configurations:•A 9764 MCO LTE connected to the backhaul network plus a 9764 MCO LTEconnected to the daisy chain port of the 9764 MCO LTE that is connected to thebackhaul network.BH13G WCDMA MCO (1W)BH2BH14G LTE MCO (2x1W)Wi-Fi APElectrical cableorOptical 250 mm breakoutcable (SM or MM)Electrical SFPorOptical SFP(SMorMM)BH2Electrical cableorOptical 250 mm breakoutcable (SM or MM)Electrical SFPorOptical SFP(SMorMM)Metro Dock double support plateBackhaulBackhaulInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationPair mount and daisy chain requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-15DRAFTDRAFT
•A 9764 MCO LTE connected to the backhaul network plus a 9764 MCO WCDMAconnected to the daisy chain port of the 9764 MCO LTE.BH14G LTE MCO (2x1W)BH2Optical 250 mm breakoutcable (SM or MM)BackhaulBH14G LTE MCO (2x1W)Wi-Fi APElectrical cableorOptical 250 mm breakoutcable (SM or MM)Electrical SFPorOptical SFP(SMorMM)Optical SFP(SMorMM)BH2BH13G WCDMA MCO (1W)BH2Optical 250 mm breakoutcable (SM or MM)BH14G LTE MCO (2x1W)Wi-Fi APElectrical cableorOptical 250 mm breakoutcable (SM or MM)Electrical SFPorOptical SFP(SMorMM)Optical SFP(SMorMM)BH2BackhaulInstallation of the 9764 Metro Dock9764 Metro Dock pre-installationPair mount and daisy chain requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-16 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
If a 9764 MCO Wi-Fi AP module is to be included in the daisy chain configuration, thefollowing Wi-Fi AP configurations are supported:•A 9764 MCO Wi-Fi AP module can be attached to each daisy chained 9764 MCOwhen the daisy chained MCOs are installed in separate locations (e.g., not co-locatedon the same pole).•If the daisy chained MCOs are co-located, only one 9764 MCO Wi-Fi AP module canbe used and the 9764 MCO Wi-Fi AP module must be attached to the 9764 MCO LTEthat is connected to the backhaul network.Note: An optional Wi-Fi Access Point may be attached to the MCO that is connectedto the backhaul network.Installation of the 9764 Metro Dock9764 Metro Dock pre-installationPair mount and daisy chain requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-17DRAFTDRAFT
9764 Metro Dock installationOverviewPurposeThis section provides the installation instructions for mounting the Alcatel-Lucent 9764Metro Dock onto either a pole or wall with or without the optional tilt mechanism. Thesection also provides the installation instructions for a pair-mount configuration. Thisdeployment option is used when a 9764 MCO V1.1 LTE 2x1W product or a 9764 MCOV1.1 B2 LTE 2x2W product is mounted with a 9764 MCO WCDMA 1W product to forma Multi-Standard Pair configuration.The available pair-mount installation options are:•a 9764 MCO V1.1 B2 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W product•a 9764 MCO V1.1 B2/B25 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W product•a 9764 MCO V1.1 B7 LTE 2x1W product is mounted with a 9764 MCO V1.0 B1WCDMA 1W product.•a 9764 MCO V1.1 B2 LTE 2x2W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,ContentsProcedure 3-1: Pole mount the 9764 Metro Dock 3-19Procedure 3-2: Pole mount the 9764 Metro Dock using optional tilt brackets 3-25Procedure 3-3: Wall mount the 9764 Metro Dock 3-35Procedure 3-4: Wall mount the 9764 Metro Dock using optional tilt brackets 3-40Procedure 3-5: Pole mount the 9764 Metro Dock in a pair configuration 3-54Procedure 3-6: Wall mount the 9764 Metro Dock in a pair configuration 3-71Installation of the 9764 Metro Dock9764 Metro Dock installationOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-18 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 3-1: Pole mount the 9764 Metro DockPurposeThis topic describes the procedures to be followed when installing the Alcatel-Lucent9764 Metro Dock onto a pole (wooden or metal).PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated in order to maximize coverage. Beforeinstallation begins you should ensure the following are in place:•Ensure adequate clearance is provided for service access•Ground cable has been routed and the site grounding system is in place•Backhaul cable has been routed and is in place•Any site specific mounting and anchor materials are available.Attention: The 9764 Metro Dock must be mounted with the appropriate mountinghardware suitable for the various supporting structures, building materials andconstruction methods. Following a site survey, it is the responsibility of the customerto ensure that:•the installation support structure is adequate and compliant with ICC IBC (2012):International Building Code, and all other national and local codes•the appropriate mounting hardware and any necessary supporting material is used.Mounting requirements and materialsThe 9764 Metro Dock can be mounted onto a wooden or metal pole. Refer to thefollowing for the installation kits, anchor materials and tools for the installation type:•For pole mount refer to, “Pole mount installation requirements” (p. 3-5).•For a list of standard tools that may be required to support the installation, refer to“Tools required for installation” (p. 3-4)Before you beginBefore mounting the 9764 Metro Dock:•Record the 9764 Metro Dock 18 digit serial number•On the 9764 Metro Dock ensure that the Metro Dock spacer is not attached. If thespacer is present remove it by unscrewing the M5 screw:Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-1: Pole mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-19DRAFTDRAFT
Metro Dock pole mount using boltsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to mount the 9764 Metro Dock onto a wooden poleusing bolts....................................................................................................................................................................................................1Measure the height at which the 9764 Metro Dock is to be positioned on the pole. Markthis point....................................................................................................................................................................................................2Using a digital compass determine the planned horizontal (left/right) orientation of the9764 Metro Dock around the pole. Mark this position....................................................................................................................................................................................................3At the identified 9764 Metro Dock position on the pole, mark the upper and lower boltanchor holes. The distance between the upper and lower bolt anchor holes should be 270mm (10.63 inches).Tip: The 9764 Metro Dock can be placed against the pole and used as a template tomark the position of the upper and lower bolt anchor holes....................................................................................................................................................................................................4Place the 9764 Metro Dock against the pole aligning the upper and lower anchor holes onthe 9764 Metro Dock with the marked anchor hole positions on the pole.M5x12countersunk screwMetro DockspacerMetro Dockspacer removedInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-1: Pole mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-20 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Tip: Use an adjustable strap, cable ties or heavy duty duct tape to temporarily hold the9764 Metro Dock against the pole while the bolts are applied....................................................................................................................................................................................................5Place a washer on each of the anchor bolts. Using socket wrench (M8) screw the 9764Metro Dock onto the pole.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................6Finally, check the 9764 Metro Dock is secure and there is no movement of the equipmenton the pole.Metro Dock pole mount using bandsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Upper and lowerMetro Dock anchor holes(9 mm diameter)M8x50 stainless steelhex head screw andM8x16x1.6 plain washerInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-1: Pole mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-21DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Perform the following procedure to mount the 9764 Metro Dock onto a pole (wooden ormetal) using standard pole bands....................................................................................................................................................................................................1Measure the height at which the 9764 Metro Dock is to be positioned on the pole. Markthis point....................................................................................................................................................................................................2Using a digital compass determine the planned horizontal (left/right) orientation of the9764 Metro Dock around the pole. Mark this position....................................................................................................................................................................................................3From the banding installation kit, take a steel pole band and thread the open end into theupper two slots on the 9764 Metro Dock....................................................................................................................................................................................................4At the marked installation point on the pole place the upper pole band around the pole atthe determined height. Carry out any required adjustment of the 9764 Metro Dock aroundthe pole so that it is pointing in the desired direction.Tip: Use an adjustable strap, cable ties or heavy duty duct tape to temporarily hold the9764 Metro Dock against the pole while the lower band is applied....................................................................................................................................................................................................5Taking the other steel band, place the band around the lower lug on the 9764 Metro Dockand the pole.Metro DockUpper Metro Dockband slotsUpper bandInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-1: Pole mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-22 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6Once the 9764 Metro Dock is in the correct position and orientation tighten and securethe bands around the pole. Refer to BAND-IT®C00169 Hand Tool OperationInstructions, PO5886....................................................................................................................................................................................................7Finally, check the banding is secure, there is no movement of the 9764 Metro Dockaround the pole and that the banding stubs (cut ends) are flattened down with a hammer.Standard pole mount exampleThe following figure shows the 9764 Metro Dock mounted onto a wooden pole usingbolts and a metal pole using bands.Metro DockLower band lugLower bandInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-1: Pole mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-23DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
How to continueAfter mounting the 9764 Metro Dock onto a pole the cables need to be connected.Continue with the, “9764 Metro Dock cabling” (p. 3-89) section.Metro Dock bandedonto metal poleMetro Dock screwedonto wooden poleInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-1: Pole mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-24 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 3-2: Pole mount the 9764 Metro Dock using optionaltilt bracketsPurposeThis topic describes the procedures to be followed when installing the Alcatel-Lucent9764 Metro Dock onto a pole (wooden or metal) using optional vertical tilt brackets.PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated in order to maximize coverage. Beforeinstallation begins you should ensure the following are in place:•Ensure adequate clearance is provided for service access•Ground cable has been routed and the site grounding system is in place•Backhaul cable has been routed and is in place•Any site specific mounting and anchor materials are available.Attention: The 9764 Metro Dock must be mounted with the appropriate mountinghardware suitable for the various supporting structures, building materials andconstruction methods. Following a site survey, it is the responsibility of the customerto ensure that:•the installation support structure is adequate and compliant with ICC IBC (2012):International Building Code, and all other national and local codes•the appropriate mounting hardware and any necessary supporting material is used.Mounting requirements and materialsThe 9764 Metro Dock can be mounted onto a wooden or metal pole. Refer to thefollowing for the installation kits, anchor materials and tools for the installation type:•For pole mount refer to, “Pole mount installation requirements” (p. 3-5).•For a list of standard tools that may be required to support the installation, refer to“Tools required for installation” (p. 3-4)Before you beginRecord the 9764 Metro Dock 18 digit serial number before mounting onto a pole.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-25DRAFTDRAFT
Bracket pole mount using boltsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure attach the vertical tilt bracket a wooden pole using bolts....................................................................................................................................................................................................1Measure the height at which the 9764 Metro Dock is to be positioned on the pole. Markthis point....................................................................................................................................................................................................2Using a digital compass determine the planned horizontal (left/right) orientation of the9764 Metro Dock around the pole. Mark this position....................................................................................................................................................................................................3At the identified 9764 Metro Dock position on the pole, mark the upper and lower boltanchor holes for the tilt bracket. The distance between the upper and lower bolt anchorholes should be 200 mm (7.87 inches).Tip: The vertical tilt bracket can be placed against the pole and used as a template tomark the position of the upper and lower bolt holes....................................................................................................................................................................................................4Depending on the required vertical tilt orientation ensure the bracket is positioned thecorrect way up before placing on the pole:If... Then... View...upward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the topInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-26 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
If... Then... View...downward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the bottom...................................................................................................................................................................................................5Place the vertical tilt bracket against the pole aligning the upper and lower anchor holeson the bracket with the marked bolt hole positions on the pole.Tip: Use an adjustable strap, cable ties or heavy duty duct tape to temporarily hold the9764 Metro Dock against the pole while the bolts are applied....................................................................................................................................................................................................6Place a washer on each of the anchor bolts. Using a socket wrench (M8) screw thevertical tilt bracket onto the pole.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Finally, check the bolts are secure and there is no movement of the bracket on the pole.Upper and lowerMetro Dock anchor holes(9 mm diameter)M8x50 stainless steelhex head screw andM8x16x1.6 plain washerInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-27DRAFTDRAFT
...................................................................................................................................................................................................8Continue onto “Attach 9764 Metro Dock to the tilt bracket” (p. 3-30)Bracket pole mount using bandsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to mount the vertical tilt bracket onto a pole (wooden ormetal) using standard pole bands....................................................................................................................................................................................................1Measure the height at which the 9764 Metro Dock is to be positioned on the pole. Markthis point....................................................................................................................................................................................................2Using a digital compass determine the planned horizontal (left/right) orientation of the9764 Metro Dock around the pole. Mark this position....................................................................................................................................................................................................3From the banding installation kit, take a steel pole band and thread the open end into theupper two slots on the tilt bracket.Taking the other steel band insert and thread the open end into the lower two slots on thetilt bracket.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-28 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................4Depending on the required vertical tilt orientation ensure the bracket is positioned thecorrect way up before placing on the pole:If... Then... View...upward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the topdownward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the bottom...................................................................................................................................................................................................5At the marked installation position on the pole wrap the upper and lower pole bandsaround the pole at the determined height. Carry out any required adjustment of the 9764Metro Dock around the pole so that it is pointing in the planned direction.Tip: Use an adjustable strap, cable ties or heavy duty duct tape to temporarily hold the9764 Metro Dock against the pole while the bands are applied.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-29DRAFTDRAFT
...................................................................................................................................................................................................6Once the 9764 Metro Dock is in the correct position and orientation tighten and securethe bands around the pole. Refer to BAND-IT®C00169 Hand Tool OperationInstructions, PO5886....................................................................................................................................................................................................7Finally, check the banding is secure, there is no movement of the bracket around the poleand that the banding stubs (cut ends) are flattened down with a hammer....................................................................................................................................................................................................8Continue onto “Attach 9764 Metro Dock to the tilt bracket” (p. 3-30)Attach 9764 Metro Dock to the tilt bracketWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach the 9764 Metro Dock to the tilt bracket....................................................................................................................................................................................................1Before attaching the 9764 Metro Dock to the tilt bracket ensure that the Metro Dockspacer is fitted and in place.Banding stubs(cut ends)Rear viewInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-30 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Unscrew and remove the two upper M6 bolts and the one lower M6 bolt from the tiltbracket....................................................................................................................................................................................................3Position the 9764 Metro Dock against the front of the tilt bracket so that the two upperbolt holes and the single lower bolt hole on the 9764 Metro Dock are aligned with thebolts holes on the tilt bracket....................................................................................................................................................................................................4From the 9764 Metro Dock side, screw in the two M6 bolts through the upper bolt holeson the 9764 Metro Dock and into the upper tilt bracket bolt holes.M5x12countersunk screwMetro DockspacerLower M6 bolt x 1Upper M6 bolts x 2Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-31DRAFTDRAFT
Note: Ensure the bolts are positioned at the upper (or lower) part of the elongated holefor better contact area with the Metro Dock (the chamfered midsection of theelongated hole is used for banding installation)....................................................................................................................................................................................................5Move the 9764 Metro Dock metal slider to the “up” position as this allows easier accessto the lower attachment bolt hole:1. insert supplied key into lock2. turn the key to its hard stop position to unlock the slider3. push the slider upwards and turn the key to its hard stop position. The slider is nowlocked in the “up” position.Slider moves upwardsMetro Dock Slider(in down position)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-32 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6From the 9764 Metro Dock side, screw in t the single M6 bolts through the lower bolthole on the 9764 Metro Dock and into the lower tilt bracket bolt hole....................................................................................................................................................................................................7Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................8Finally move the 9764 Metro Dock metal slider to the “down” position:1. turn the key to its hard stop position to unlock the slider. The slider will automaticallyspring into the “down” position.2. turn the key to its hard stop position. The slider is now locked in the “down” positionand the key can be removed from the lock.Pole mount example (with vertical tilt)The following figure shows the 9764 Metro Dock, with vertical tilt, mounted onto awooden pole using bolts and a metal pole using bands.Lower Metro Dockattachment boltInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-33DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
How to continueAfter mounting the 9764 Metro Dock onto a pole the cables need to be connected.Continue with the, “9764 Metro Dock cabling” (p. 3-89) section.Metro Dock mounted onwooden pole with vertical tilt Metro Dock mounted onmetal pole with vertical tiltInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-2: Pole mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-34 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 3-3: Wall mount the 9764 Metro DockPurposeThis topic describes the procedures to be followed when installing the Alcatel-Lucent9764 Metro Dock directly onto a wall or solid flat surface.PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated in order to maximize coverage. Beforeinstallation begins you should ensure the following are in place:•Ensure adequate clearance is provided for service access•Ground cable has been routed and the site grounding system is in place•Backhaul cable has been routed and is in place•Any site specific fixing materials are available (for example, bolts, washers and wallplug materials).Attention: The 9764 Metro Dock must be mounted with the appropriate mountinghardware suitable for the various supporting structures, building materials andconstruction methods. Following a site survey, it is the responsibility of the customerto ensure that:•the installation support structure is adequate and compliant with ICC IBC (2012):International Building Code, and all other national and local codes•the appropriate mounting hardware and any necessary recommended supportinganchor fixings are used.Mounting requirements and materialsThe 9764 Metro Dock is less than 1 kg (2.2 lbs) and can be easily mounted onto solidconcrete or wooden flat surface. Refer to the following for the installation kits, anchormaterials and tools for the installation type:•For wall mount refer to, “Wall mount installation requirements” (p. 3-9).•For a list of standard tools that may be required to support the installation, see “Toolsrequired for installation” (p. 3-4)Before you beginBefore mounting the 9764 Metro Dock:•Record the 9764 Metro Dock 18 digit serial number•On the 9764 Metro Dock ensure that the Metro Dock spacer is not attached. If thespacer is present remove it by unscrewing the M5 screw:Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-3: Wall mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-35DRAFTDRAFT
Perform standard wall mount installationWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to mount the 9764 Metro Dock directly onto a wall....................................................................................................................................................................................................1Measure the height at which the 9764 Metro Dock is to be positioned on the wall. Markthis point....................................................................................................................................................................................................2At the selected installation location, mark the points on the wall for the anchor holes. Seehole spacing pattern below to use as a guide:M5x12countersunk screwMetro DockspacerMetro Dockspacer removedInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-3: Wall mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-36 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Tip: The wall spacer bracket can placed against the wall and used as a template tomark the position of the upper and lower anchor holes.Check the horizontal position of the planned holes with a level....................................................................................................................................................................................................3If.. Then..Surface structure is concrete 1. Drill two upper holes and one lower hole at themarked points to the appropriate depth.2. Insert screw anchor plugs (Rawlnut M6x50) into thedrilled holes and, using a hammer, tap home untilthe plugs are flush with the wall.Surface structure is wood Proceed with the next step....................................................................................................................................................................................................4Move the 9764 Metro Dock metal slider to the “up” position as this allows easier accessto the lower attachment bolt hole:1. insert supplied key into lock2. turn the key to its hard stop position to unlock the slider3. Push the slider upwards and turn the key to its hard stop position. The slider is nowlocked in the “up” position.267mm(10.51 inches)52mm(2.05 inches)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-3: Wall mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-37DRAFTDRAFT
...................................................................................................................................................................................................5Place washers onto the anchor bolts.Note: The type of anchor bolt used depends on the surface structure:•Wooden surface: use Screw Hex T M8x70 stainless steel•Concrete surface: use Screw CHC M6x80 stainless steel...................................................................................................................................................................................................6Align the 9764 Metro Dock bolt holes with the wall spacer bolt holes and thread boltsthrough the corresponding set of holes....................................................................................................................................................................................................7Screw in the upper and lower bolts into the drilled anchor holes for a concrete surface, ordirectly into the wooden surface, to the appropriate depth so that the wall spacer and 9764Metro Dock are securely attached to the wall.Recommended screw torque; 7.0 N.m (62.0 lb.in).Slider moves upwardsMetro Dock Slider(in down position)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-3: Wall mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-38 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................8Finally move the 9764 Metro Dock metal slider to the “down” position:1. turn the key to its hard stop position to unlock the slider. The slider will automaticallyspring into the “down” position2. turn the key to its hard stop position. The slider is now locked in the “down” positionand the key can be removed from the lock.Standard wall mount exampleThe following figure depicts a standard wall mount.How to continueAfter mounting the 9764 Metro Dock onto a wall the cables need to be connected.Continue with the, “9764 Metro Dock cabling” (p. 3-89) section.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-3: Wall mount the 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-39DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 3-4: Wall mount the 9764 Metro Dock using optionaltilt bracketsPurposeThis topic describes the procedures to be followed when the Alcatel-Lucent 9764 MetroDock is required to be mounted onto a wall or solid flat surface using tilt brackets(vertical, horizontal or combined horizontal/vertical).PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated in order to maximize coverage. Beforeinstallation begins you should ensure the following are in place:•Ensure adequate clearance is provided for service access•Ground cable has been routed and the site grounding system is in place•Backhaul cable has been routed and is in place•Any site specific fixing materials are available (for example, bolts, washers and wallplug materials).Attention: The 9764 Metro Dock must be mounted with the appropriate mountinghardware suitable for the various supporting structures, building materials andconstruction methods. Following a site survey, it is the responsibility of the customerto ensure that:•the installation support structure is adequate and compliant with ICC IBC (2012):International Building Code, and all other national and local codes•the appropriate mounting hardware and any necessary supporting anchor fixingsare used.Mounting requirements and materialsThe 9764 Metro Dock is less than 1 kg (2.2 lbs) and can be easily mounted onto solidconcrete or wooden flat surface. Refer to the following for the installation kits, anchormaterials and tools for the installation type:•For wall mount refer to, “Wall mount installation requirements” (p. 3-9).•For a list of standard tools that may be required to support the installation, see “Toolsrequired for installation” (p. 3-4)Before you beginRecord the 9764 Metro Dock 18 digit serial number before mounting onto a wall.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-40 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Prepare surface for bracket mountingWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to prepare a wall or solid flat surface for mounting tiltbrackets....................................................................................................................................................................................................1At the selected installation location, mark the points on the wall for the bracket anchorholes. See drill hole pattern below to use as a guide:Tip: If the tilt bracket is available it can be placed against the wall and be used as atemplate to mark the points on the wall for the bracket anchor holes.Check the horizontal marked position of the holes with a level.52 mm(2.05 inches)270 mm(10.63 inches)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-41DRAFTDRAFT
...................................................................................................................................................................................................2If.. Then..Surface structure is concrete 1. Drill two upper holes and one lower hole at themarked points to the appropriate depth.2. Insert screw anchor plugs (Rawlnut M6x50) into thedrilled holes and, using a hammer, tap home untilthe plugs are flush with the wall.Surface structure is wood Mount combined horizontal/vertical tilt brackets...................................................................................................................................................................................................3Once the mounting surface has been prepared the tilt brackets can be attached. Continuewith one of the following procedures depending on the tilt configuration:If.. Then..Attaching vertical tiltbracketsCarry out the procedure, “Mount the vertical tilt bracket”(p. 3-42)Attaching horizontal tiltbracketsCarry out the procedure, “Mount the horizontal tilt bracket”(p. 3-44)Attaching combinedhorizontal and vertical tiltbracketsCarry out the procedure, “Mount combined horizontal/verticaltilt brackets” (p. 3-46)Mount the vertical tilt bracketWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-42 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Perform the following procedure to attach a vertical tilt bracket onto a flat surface or wall....................................................................................................................................................................................................1Remove the two tilt angle positioning gauge bolts on either side of the vertical tilt bracketand allow the front part of the bracket to pivot away allowing easier access to the bracketanchor holes....................................................................................................................................................................................................2Depending on the required vertical tilt orientation ensure the bracket is positioned thecorrect way up before placing on the wall:If... Then... View...upward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the topdownward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the bottom...................................................................................................................................................................................................3Place washers onto the anchor bolts.Tilt angle positioninggauge boltTilt angle positioninggauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-43DRAFTDRAFT
Note: The type of anchor bolt used depends on the surface structure:•Wooden surface: use Screw Hex T M8x70 stainless steel•Concrete surface: use Screw CHC M6x80 stainless steel...................................................................................................................................................................................................4At the selected installation location, position the tilt bracket so the anchor holes on thebracket align with the anchor holes either drilled or marked on the wall....................................................................................................................................................................................................5For each anchor hole (upper and lower) insert bolts through the tilt bracket anchor holes....................................................................................................................................................................................................6Screw the upper and lower bolts into the drilled anchor holes for a concrete surface, ordirectly into the wooden surface, to the appropriate depth so that the bracket is firmlysecured to the wall or flat surface.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Once the tilt bracket is mounted the 9764 Metro Dock can be attached. Continue with“Attach 9764 Metro Dock to the tilt bracket” (p. 3-30).Mount the horizontal tilt bracketWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach the horizontal tilt bracket onto a flat surface orwall....................................................................................................................................................................................................1Remove the two tilt angle positioning gauge bolts from the top and bottom of thehorizontal tilt bracket and allow the front part of the bracket to pivot away allowing easieraccess to the bracket anchor holes.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-44 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Depending on the required horizontal tilt orientation ensure the bracket is the correct wayup before securing the bracket onto the wall:If... Then... View...left horizontal tilt is required the tilt bracket must bepositioned with the pivot pointon the leftright horizontal tilt is required the tilt bracket must bepositioned with the pivot pointon the right...................................................................................................................................................................................................3Place washers onto the anchor bolts.Note: The type of anchor bolt used depends on the surface structure:•Wooden surface: use Screw Hex T M8x70 stainless steel•Concrete surface: use Screw CHC M6x80 stainless steelTilt anglepositioning gauge boltTilt anglepositioning gauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-45DRAFTDRAFT
...................................................................................................................................................................................................4At the selected installation location, position the tilt bracket so the anchor holes on thebracket align with the anchor holes either drilled or marked on the wall....................................................................................................................................................................................................5For each anchor hole (upper and lower) insert bolts through the tilt bracket anchor holes....................................................................................................................................................................................................6Screw the upper and lower bolts into the drilled anchor holes for a concrete surface, ordirectly into the wooden surface, to the appropriate depth so that the bracket is firmlysecured to the wall or flat surface.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Once the tilt bracket is mounted the 9764 Metro Dock can be attached. Continue with“Attach 9764 Metro Dock to the tilt bracket” (p. 3-30).Mount combined horizontal/vertical tilt bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach the combined horizontal/vertical tilt bracketonto a flat surface or wall....................................................................................................................................................................................................1Firstly combine the horizontal and vertical tilt brackets.Unscrew and remove the two upper and two lower M6 bolts on the front of the horizontaltilt bracket.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-46 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Align the attachment holes on the vertical tilt bracket with the attachments holes on thehorizontal tilt bracket.Important! Ensure the brackets are combined in the correct way based on the plannedhorizontal and vertical tilt orientation of the equipment.If... Then... View...left horizontal tilt anddownward vertical tilt isrequiredorright horizontal tilt andupward vertical tilt is requiredthe brackets should be attached withthe horizontal bracket pivot point onthe left and the vertical bracket pivotpoint at the bottomNote: when positioning on a wall thebracket assembly can be turnedthrough 1800for right horizontal tiltand upward vertical tiltright horizontal tilt anddownward vertical tilt isrequiredorleft horizontal tilt and upwardvertical tilt is requiredthe brackets should be attached withthe horizontal bracket pivot point onthe right and the vertical bracket pivotpoint at the bottomNote: when positioning on a wall thebracket assembly can be turnedthrough 1800for left horizontal tilt andupward vertical tilt...................................................................................................................................................................................................3Insert the two upper and two lower bolts through the attachment holes on the vertical tiltbracket and through the attachment holes on the horizontal tilt bracket.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-47DRAFTDRAFT
For each bolt, screw on the retaining nut. Using a 10 mm ratchet wrench, tighten the twoupper and two lower M6 retaining bolts so that the brackets are securely attached.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................4The horizontal and vertical tilt brackets are now combined and can be attached to thewall.Remove the two tilt angle positioning gauge bolts from the top and bottom of thehorizontal tilt bracket and allow the front part of the bracket to pivot away allowingaccess to the bracket anchor holes....................................................................................................................................................................................................5Place washers onto the anchor bolts.Note: The type of anchor bolt used depends on the surface structure:•Wooden surface: use Screw Hex T M8x70 stainless steel•Concrete surface: use Screw CHC M6x80 stainless steelTilt anglepositioning gauge boltTilt anglepositioning gauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-48 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6At the selected installation location, position the tilt bracket so the anchor holes on thebracket align with the anchor holes either drilled or marked on the wall.Important! Ensure the combined brackets are positioned on the wall correctly basedon the planned horizontal and vertical tilt orientation of the equipment....................................................................................................................................................................................................7For each anchor hole (upper and lower) insert bolts through the tilt bracket anchor holes....................................................................................................................................................................................................8Screw the upper and lower bolts into the drilled anchor holes for a concrete surface, ordirectly into the wooden surface, to the appropriate depth so that the bracket is firmlysecured to the wall or flat surface.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................9Once the tilt bracket is mounted the 9764 Metro Dock can be attached. Continue with“Attach 9764 Metro Dock to the tilt bracket” (p. 3-30).Attach 9764 Metro Dock to the tilt bracketWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach the 9764 Metro Dock to the tilt bracket....................................................................................................................................................................................................1Before attaching the 9764 Metro Dock to the tilt bracket ensure that the Metro Dockspacer is fitted and in place.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-49DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Unscrew and remove the two upper M6 bolts and the one lower M6 bolt from the tiltbracket....................................................................................................................................................................................................3Position the 9764 Metro Dock against the front of the tilt bracket so that the two upperbolt holes and the single lower bolt hole on the 9764 Metro Dock are aligned with thebolts holes on the tilt bracket....................................................................................................................................................................................................4From the 9764 Metro Dock side, screw in the two M6 bolts through the upper bolt holeson the 9764 Metro Dock and into the upper tilt bracket bolt holes.M5x12countersunk screwMetro DockspacerLower M6 bolt x 1Upper M6 bolts x 2Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-50 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Note: Ensure the bolts are positioned at the upper (or lower) part of the elongated holefor better contact area with the Metro Dock (the chamfered midsection of theelongated hole is used for banding installation)....................................................................................................................................................................................................5Move the 9764 Metro Dock metal slider to the “up” position as this allows easier accessto the lower attachment bolt hole:1. insert supplied key into lock2. turn the key to its hard stop position to unlock the slider3. push the slider upwards and turn the key to its hard stop position. The slider is nowlocked in the “up” position.Slider moves upwardsMetro Dock Slider(in down position)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-51DRAFTDRAFT
...................................................................................................................................................................................................6From the 9764 Metro Dock side, screw in t the single M6 bolts through the lower bolthole on the 9764 Metro Dock and into the lower tilt bracket bolt hole....................................................................................................................................................................................................7Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................8Finally move the 9764 Metro Dock metal slider to the “down” position:1. turn the key to its hard stop position to unlock the slider. The slider will automaticallyspring into the “down” position.2. turn the key to its hard stop position. The slider is now locked in the “down” positionand the key can be removed from the lock.Wall mount with horizontal/vertical tilt exampleThe following figure depicts a wall mount installation with horizontal/vertical tilt.Lower Metro Dockattachment boltInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-52 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
How to continueAfter mounting the 9764 Metro Dock onto a wall the cables need to be connected.Continue with the, “9764 Metro Dock cabling” (p. 3-89) section.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-4: Wall mount the 9764 Metro Dock usingoptional tilt brackets........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-53DRAFTDRAFT
Procedure 3-5: Pole mount the 9764 Metro Dock in a pairconfigurationPurposeThis topic describes the procedures to be followed when installing the Alcatel-Lucent9764 Metro Dock in a pair mount configuration onto a pole. This deployment option isused when a 9764 MCO V1.1 LTE 2x1W product or a 9764 MCO LTE 2x2W product ismounted with a 9764 MCO WCDMA 1W product to form a Multi-Standard Pairconfiguration.The available pair-mount installation options are:•a 9764 MCO V1.1 B2 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W product•a 9764 MCO V1.1 B2/B25 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W product•a 9764 MCO V1.1 B2 LTE 2x2W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,•a 9764 MCO V1.1 B7 LTE 2x1W product is mounted with a 9764 MCO V1.0 B1WCDMA 1W product.PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated in order to maximize coverage. Beforeinstallation begins you should ensure the following are in place:•Ensure adequate clearance is provided for service access•Ground cable has been routed and the site grounding system is in place•Backhaul cable has been routed and is in place•Any site specific mounting and anchor materials are available.Attention: The 9764 Metro Dock must be mounted with the appropriate mountinghardware suitable for the various supporting structures, building materials andconstruction methods. Following a site survey, it is the responsibility of the customerto ensure that:•the installation support structure is adequate and compliant with ICC IBC (2012):International Building Code, and all other national and local codes•the appropriate mounting hardware and any necessary supporting material is used.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-54 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Mounting requirements and materialsFor pole mounting the 9764 Metro Dock in a pair mount configuration refer to thefollowing for the installation kits, anchor materials and tools required for this installationtype:•For pole mount installation kits and materials refer to, “Pole mount installationrequirements” (p. 3-5).•For a list of standard tools that may be required to support the installation, see “Toolsrequired for installation” (p. 3-4)Before you beginRecord both the 9764 Metro Dock 18 digit serial number for future reference beforemounting onto the support bracket.Attach support plate to a poleWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to mount the double Metro Dock support plate onto apole. The procedure also includes attaching the extension plate to the support plate.Note: The extension plate is required to mount the 3G MCO (allowing alignment with the4G MCO in pair-mount deployment) and can be attached to either the left or right side ofthe double Metro Dock support plate, depending on customer preference....................................................................................................................................................................................................1Measure the height at which the double Metro Dock support plate is to be positioned onpole. Mark this point....................................................................................................................................................................................................2Using a digital compass determine the planned horizontal (left/right) orientation of thesupport plate around the pole. Mark this position....................................................................................................................................................................................................3From the banding installation kit, locate the two steel pole bands. Thread the open end ofone band through the upper two banding slots on the support plate and the other pole bandthrough the lower two banding slots on the support plate.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-55DRAFTDRAFT
...................................................................................................................................................................................................4At the marked installation point on the pole place the upper and lower pole bands aroundthe pole at the determined height. Carry out any required adjustment of the support platearound the pole so that it is pointing in the desired direction....................................................................................................................................................................................................5Once the support plate is in the correct position and orientation tighten and secure thebands around the pole using the banding tool.Refer to BAND-IT ® C00169 Hand Tool Operation Instructions, PO5886....................................................................................................................................................................................................6Check the banding is secure, there is no movement of the support plate around the poleand that the banding stubs (cut ends) are flattened down with a hammer.Upper bracket banding slotsLower bracket banding slotsInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-56 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................7Finally attach the extension plate to the double Metro Dock support plate.Note: The extension plate used for mounting the 3G MCO can be attached to eitherthe left or the right side of the double support plate depending on customer preference(the example shows the extension plate attached on the right side of the doublesupport plate).1. Remove the three bolts (either the left set of three or the right set of three) from thesupport plate.2. Position the extension plate in front of the support plate so that both sets ofattachment holes are aligned.3. Replace the set of three bolts. Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................8Once the Metro Dock double support plate (including extension plate) has been mountedonto a pole continue with one of the following procedures:•If no tilt is required, continue with “Attach 9764 Metro Dock to brackets” (p. 3-66).•If tilt is required continue with one of the following procedures depending on the tiltconfiguration:For.. Then..Vertical tilt only Carry out the procedure, “Attach vertical tilt brackets” (p. 3-58)Horizontal tilt only Carry out the procedure, “Attach horizontal tilt bracket”(p. 3-60)Combined horizontaland vertical tiltCarry out the procedure, “Attach combined horizontal/verticaltilt brackets” (p. 3-63)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-57DRAFTDRAFT
Attach vertical tilt bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach vertical tilt brackets to the double supportbracket....................................................................................................................................................................................................1Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from boththe support bracket and the extension plate....................................................................................................................................................................................................2Remove the two tilt angle positioning gauge bolts on either side of the vertical tilt bracketand allow the front part of the bracket to pivot away allowing easier access to the bracketanchor holes.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-58 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................3Depending on the required vertical tilt orientation ensure the bracket is positioned thecorrect way up before placing on the support plate:If... Then... View...upward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the topdownward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the bottom...................................................................................................................................................................................................4Position the vertical tilt bracket against the front of the support bracket so that the twoupper bolt holes and the single lower bolt hole on the tilt bracket are aligned with thebolts holes on the support bracket....................................................................................................................................................................................................5From the tilt bracket side, screw in the two upper and one lower M6 bolts through theanchor holes on the tilt bracket and into the support bracket bolt holes.Tilt angle positioninggauge boltTilt angle positioninggauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-59DRAFTDRAFT
...................................................................................................................................................................................................6Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Repeat the above procedure for attaching the second vertical tilt bracket to the extensionplate....................................................................................................................................................................................................8Once the tilt brackets have been attached to the support plate the 9764 Metro Dock(s) canbe attached to the tilt brackets. Continue with “Attach 9764 Metro Dock to brackets”(p. 3-66).Attach horizontal tilt bracketWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach horizontal tilt brackets to the double supportbracket....................................................................................................................................................................................................1Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from boththe support bracket and the extension plate.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-60 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Remove the two tilt angle positioning gauge bolts from the top and bottom of thehorizontal tilt bracket and allow the front part of the bracket to pivot away allowing easieraccess to the bracket anchor holes.Tilt anglepositioning gauge boltTilt anglepositioning gauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-61DRAFTDRAFT
...................................................................................................................................................................................................3Depending on the required horizontal tilt orientation ensure the bracket is the correct wayup before securing the tilt brackets to the support plate:If... Then... View...left horizontal tilt is required the tilt bracket must bepositioned with the pivot pointon the leftright horizontal tilt is required the tilt bracket must bepositioned with the pivot pointon the right...................................................................................................................................................................................................4Position the horizontal tilt bracket against the front of the support bracket so that the twoupper bolt holes and the single lower bolt hole on the tilt bracket are aligned with thebolts holes on the support bracket....................................................................................................................................................................................................5From the tilt bracket side, screw in the two upper and one lower M6 bolts through theanchor holes on the tilt bracket and into the support bracket bolt holes....................................................................................................................................................................................................6Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Repeat the above procedure for attaching the second horizontal tilt bracket to theextension plate.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-62 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................8Once the tilt brackets have been attached to the support plate the 9764 Metro Dock(s) canbe attached to the tilt brackets. Continue with “Attach 9764 Metro Dock to brackets”(p. 3-66).Attach combined horizontal/vertical tilt bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach the combined horizontal/vertical tilt brackets tothe double support bracket....................................................................................................................................................................................................1Firstly combine the horizontal and vertical tilt brackets by unscrewing and removing thetwo upper and two lower M6 bolts on the front of the horizontal tilt bracket....................................................................................................................................................................................................2Align the attachment holes on the vertical tilt bracket with the attachments holes on thehorizontal tilt bracket.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-63DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Important! Ensure the brackets are combined in the correct way based on the plannedhorizontal and vertical tilt orientation of the equipment.If... Then... View...left horizontal tilt anddownward vertical tilt isrequiredorright horizontal tilt andupward vertical tilt is requiredthe brackets should be attached withthe horizontal bracket pivot point onthe left and the vertical bracket pivotpoint at the bottomNote: when positioning on a wall thebracket assembly can be turnedthrough 1800for right horizontal tiltand upward vertical tiltright horizontal tilt anddownward vertical tilt isrequiredorleft horizontal tilt and upwardvertical tilt is requiredthe brackets should be attached withthe horizontal bracket pivot point onthe right and the vertical bracket pivotpoint at the bottomNote: when positioning on a wall thebracket assembly can be turnedthrough 1800for left horizontal tilt andupward vertical tilt...................................................................................................................................................................................................3Insert the two upper and two lower bolts through the attachment holes on the vertical tiltbracket and through the attachment holes on the horizontal tilt bracket.Using a 10 mm ratchet wrench, tighten the two upper and two lower M6 retaining bolts sothat the brackets are securely attached.Recommended screw torque; 7.0 N.m (62.0 lb.in).Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-64 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from boththe support bracket and the extension plate....................................................................................................................................................................................................5Remove the two tilt angle positioning gauge bolts from the top and bottom of thehorizontal tilt bracket and allow the front part of the bracket to pivot away allowing easieraccess to the bracket anchor holes....................................................................................................................................................................................................6Position the combined tilt bracket against the front of the support bracket so that the twoupper bolt holes and the single lower bolt hole on the tilt bracket are aligned with thebolts holes on the support bracket.Tilt anglepositioning gauge boltTilt anglepositioning gauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-65DRAFTDRAFT
...................................................................................................................................................................................................7From the tilt bracket side, screw in the two upper and one lower M6 bolts through theanchor holes on the tilt bracket and into the support bracket bolt holes....................................................................................................................................................................................................8Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................9Repeat the above procedure for attaching the second horizontal/vertical tilt bracket to theextension plate....................................................................................................................................................................................................10 Once the tilt brackets have been attached to the support plate the 9764 Metro Dock(s) canbe attached to the tilt brackets. Continue with “Attach 9764 Metro Dock to brackets”(p. 3-66).Attach 9764 Metro Dock to bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach a pair of 9764 Metro Dock's directly to thesupport plate or to tilt brackets (attached to the support plate)....................................................................................................................................................................................................1Before attaching each 9764 Metro Dock ensure that the Metro Dock spacer is fitted and inplace on both 9764 Metro Dock's.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-66 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from theboth sides (left and right) of the support plate or if tilt brackets are attached from each ofthe tilt brackets....................................................................................................................................................................................................3Position a 9764 Metro Dock against the front of the bracket (support plate or tilt) so thatthe two upper bolt holes and the single lower bolt hole on the 9764 Metro Dock arealigned with the bolts holes on the bracket....................................................................................................................................................................................................4From the 9764 Metro Dock side, screw in the two M6 bolts back through the upper boltholes on the 9764 Metro Dock and into the upper bracket bolt holes.M5x12countersunk screwMetro Dockspacer9764 Metro Dock attachmentbolts on support plate9764 Metro Dock attachmentbolts on tilt bracketInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-67DRAFTDRAFT
Note: Ensure the bolts are positioned at the upper (or lower) part of the elongated holefor better contact area with the Metro Dock (the chamfered midsection of theelongated hole is used for banding installation)....................................................................................................................................................................................................5Move the 9764 Metro Dock metal slider to the “up” position as this allows easier accessto the lower attachment bolt hole:1. insert supplied key into lock2. turn the key to its hard stop position to unlock the slider3. push the slider upwards and turn the key to its hard stop position. The slider is nowlocked in the “up” position.Slider moves upwardsMetro Dock Slider(in down position)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-68 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6From the 9764 Metro Dock side, screw in the single M6 bolts back through the lower bolthole on the 9764 Metro Dock and into the lower bracket bolt hole....................................................................................................................................................................................................7Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................8Finally move the 9764 Metro Dock metal slider to the “down” position:1. turn the key to its hard stop position to unlock the slider. The slider will automaticallyspring into the “down” position.2. turn the key to its hard stop position. The slider is now locked in the “down” positionand the key can be removed from the lock....................................................................................................................................................................................................9Repeat the above procedure for attaching the second 9764 Metro Dock to the other side ofthe support plate or, if tilt brackets are attached, to the second tilt bracket.Pole mount example (with tilt)The following figure shows an example of a 9764 Metro Dock pair configuration (withtilt brackets attached), mounted onto a pole.Lower Metro Dockattachment boltInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-69DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
How to continueAfter mounting the 9764 Metro Dock pair onto the double support bracket the cables needto be connected. Continue with the, “9764 Metro Dock cabling” (p. 3-89) section.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-5: Pole mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-70 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 3-6: Wall mount the 9764 Metro Dock in a pairconfigurationPurposeThis topic describes the procedures to be followed when installing the Alcatel-Lucent9764 Metro Dock in a pair-mount configuration onto a wall or flat surface. Thisdeployment option is used when a 9764 MCO V1.1 LTE 2x1W product or a 9764 MCOLTE 2x2W product is mounted with a 9764 MCO WCDMA 1W product to form aMulti-Standard Pair configuration.The available pair-mount installation options are:•a 9764 MCO V1.1 B2 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W product•a 9764 MCO V1.1 B2/B25 LTE 2x1W product is mounted with a 9764 MCO V1.0 B2WCDMA 1W product•a 9764 MCO V1.1 B2 LTE 2x2W product is pair-mounted with a 9764 MCO V1.0 B2WCDMA 1W,•a 9764 MCO V1.1 B7 LTE 2x1W product is mounted with a 9764 MCO V1.0 B1WCDMA 1W product.PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated in order to maximize coverage. Beforeinstallation begins you should ensure the following are in place:•Ensure adequate clearance is provided for service access•Ground cable has been routed and the site grounding system is in place•Backhaul cable has been routed and is in place•Any site specific fixing materials are available (for example, bolts, washers and wallplug materials).Attention: The 9764 Metro Dock must be mounted with the appropriate mountinghardware suitable for the various supporting structures, building materials andconstruction methods. Following a site survey, it is the responsibility of the customerto ensure that:•the installation support structure is adequate and compliant with ICC IBC (2012):International Building Code, and all other national and local codes•the appropriate mounting hardware and any necessary recommended supportinganchor fixings are used.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-71DRAFTDRAFT
Mounting requirements and materialsFor wall mounting the 9764 Metro Dock in a pair-mount configuration refer to thefollowing for the installation kits, anchor materials and tools required for this installationtype:•For wall mount installation kits and materials refer to, “Wall mount installationrequirements” (p. 3-9).•For a list of standard tools that may be required to support the installation, see “Toolsrequired for installation” (p. 3-4)Before you beginRecord both the 9764 Metro Dock 18 digit serial numbers for future reference beforemounting onto the support bracket.Attach support plate to a wall or flat surfaceWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to mount the double Metro Dock support plate onto awall or flat surface. The procedure also includes attaching the extension plate to thesupport plate.Note: The extension plate is required to mount the 3G MCO (allowing alignment with the4G MCO in pair-mount deployment) and can be attached to either the left or right side ofthe double Metro Dock support plate, depending on customer preference....................................................................................................................................................................................................1Measure the height at which the double Metro Dock support plate is to be positioned onthe wall. Mark this point....................................................................................................................................................................................................2At the selected installation location, mark the points on the wall for the six support plateanchor holes. See pattern below for the hole spacing dimensions.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-72 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Tip: If the double Metro Dock support plate is available it can placed against the walland used as a template to mark the position of the upper and lower anchor holes....................................................................................................................................................................................................3If.. Then..Surface structure is concrete 1. Drill three upper holes and three lower holes at themarked points to the appropriate depth.2. Insert screw anchor plugs (Rawlnut M6x50) into thedrilled holes and, using a hammer, tap home untilthe plugs are flush with the wall.Surface structure is wood Proceed with the next step....................................................................................................................................................................................................4Place washers onto the anchor bolts.Note: The type of anchor bolt used depends on the surface structure:•Concrete surface: use Screw CHC M6x80 stainless steel•Wooden surface: use Screw Hex T M8x70 stainless steel120 mm(4.7 inches)200 mm(7.87 inches)120 mm(4.7 inches)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-73DRAFTDRAFT
...................................................................................................................................................................................................5Align the double Metro Dock support plate bolt holes with the corresponding holes on thewall.Screw in the upper and lower bolts into the drilled anchor holes for a concrete surface, ordirectly into the wooden surface, to the appropriate depth so that the support plate issecurely attached to the wall. Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................6Finally attach the extension plate to the double Metro Dock support plate.Note: The extension plate used for mounting the 3G MCO can be attached to eitherthe left or the right side of the double support plate depending on customer preference(the example shows the extension plate attached on the right side of the doublesupport plate).1. Remove the three bolts (either the left set of three or the right set of three) from thesupport plate.2. Position the extension plate in front of the support plate so that both sets ofattachment holes are aligned.3. Replace the set of three bolts. Recommended screw torque; 7.0 N.m (62.0 lb.in).Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-74 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................7Once the Metro Dock double support plate (including extension plate) has been mountedonto a wall or flat surface continue with one of the following procedures:•If no tilt is required, continue with “Attach 9764 Metro Dock to brackets” (p. 3-66).•If tilt is required continue with one of the following procedures depending on the tiltconfiguration:For.. Then..Vertical tilt only Carry out the procedure, “Attach vertical tilt brackets” (p. 3-58)Horizontal tilt only Carry out the procedure, “Attach horizontal tilt bracket”(p. 3-60)Combined horizontaland vertical tiltCarry out the procedure, “Attach combined horizontal/verticaltilt brackets” (p. 3-63)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-75DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Attach vertical tilt bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach vertical tilt brackets to the double supportbracket....................................................................................................................................................................................................1Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from boththe support bracket and the extension plate....................................................................................................................................................................................................2Remove the two tilt angle positioning gauge bolts on either side of the vertical tilt bracketand allow the front part of the bracket to pivot away allowing easier access to the bracketanchor holes.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-76 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................3Depending on the required vertical tilt orientation ensure the bracket is positioned thecorrect way up before placing on the support plate:If... Then... View...upward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the topdownward vertical tilt isrequiredthe tilt bracket must bepositioned with the pivot pointat the bottom...................................................................................................................................................................................................4Position the vertical tilt bracket against the front of the support bracket so that the twoupper bolt holes and the single lower bolt hole on the tilt bracket are aligned with thebolts holes on the support bracket....................................................................................................................................................................................................5From the tilt bracket side, screw in the two upper and one lower M6 bolts through theanchor holes on the tilt bracket and into the support bracket bolt holes.Tilt angle positioninggauge boltTilt angle positioninggauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-77DRAFTDRAFT
...................................................................................................................................................................................................6Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Repeat the above procedure for attaching the second vertical tilt bracket to the extensionplate....................................................................................................................................................................................................8Once the tilt brackets have been attached to the support plate the 9764 Metro Dock(s) canbe attached to the tilt brackets. Continue with “Attach 9764 Metro Dock to brackets”(p. 3-66).Attach horizontal tilt bracketWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach horizontal tilt brackets to the double supportbracket....................................................................................................................................................................................................1Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from boththe support bracket and the extension plate.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-78 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Remove the two tilt angle positioning gauge bolts from the top and bottom of thehorizontal tilt bracket and allow the front part of the bracket to pivot away allowing easieraccess to the bracket anchor holes.Tilt anglepositioning gauge boltTilt anglepositioning gauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-79DRAFTDRAFT
...................................................................................................................................................................................................3Depending on the required horizontal tilt orientation ensure the bracket is the correct wayup before securing the tilt brackets to the support plate:If... Then... View...left horizontal tilt is required the tilt bracket must bepositioned with the pivot pointon the leftright horizontal tilt is required the tilt bracket must bepositioned with the pivot pointon the right...................................................................................................................................................................................................4Position the horizontal tilt bracket against the front of the support bracket so that the twoupper bolt holes and the single lower bolt hole on the tilt bracket are aligned with thebolts holes on the support bracket....................................................................................................................................................................................................5From the tilt bracket side, screw in the two upper and one lower M6 bolts through theanchor holes on the tilt bracket and into the support bracket bolt holes....................................................................................................................................................................................................6Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................7Repeat the above procedure for attaching the second horizontal tilt bracket to theextension plate.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-80 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................8Once the tilt brackets have been attached to the support plate the 9764 Metro Dock(s) canbe attached to the tilt brackets. Continue with “Attach 9764 Metro Dock to brackets”(p. 3-66).Attach combined horizontal/vertical tilt bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach the combined horizontal/vertical tilt brackets tothe double support bracket....................................................................................................................................................................................................1Firstly combine the horizontal and vertical tilt brackets by unscrewing and removing thetwo upper and two lower M6 bolts on the front of the horizontal tilt bracket....................................................................................................................................................................................................2Align the attachment holes on the vertical tilt bracket with the attachments holes on thehorizontal tilt bracket.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-81DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Important! Ensure the brackets are combined in the correct way based on the plannedhorizontal and vertical tilt orientation of the equipment.If... Then... View...left horizontal tilt anddownward vertical tilt isrequiredorright horizontal tilt andupward vertical tilt is requiredthe brackets should be attached withthe horizontal bracket pivot point onthe left and the vertical bracket pivotpoint at the bottomNote: when positioning on a wall thebracket assembly can be turnedthrough 1800for right horizontal tiltand upward vertical tiltright horizontal tilt anddownward vertical tilt isrequiredorleft horizontal tilt and upwardvertical tilt is requiredthe brackets should be attached withthe horizontal bracket pivot point onthe right and the vertical bracket pivotpoint at the bottomNote: when positioning on a wall thebracket assembly can be turnedthrough 1800for left horizontal tilt andupward vertical tilt...................................................................................................................................................................................................3Insert the two upper and two lower bolts through the attachment holes on the vertical tiltbracket and through the attachment holes on the horizontal tilt bracket.Using a 10 mm ratchet wrench, tighten the two upper and two lower M6 retaining bolts sothat the brackets are securely attached.Recommended screw torque; 7.0 N.m (62.0 lb.in).Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-82 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from boththe support bracket and the extension plate....................................................................................................................................................................................................5Remove the two tilt angle positioning gauge bolts from the top and bottom of thehorizontal tilt bracket and allow the front part of the bracket to pivot away allowing easieraccess to the bracket anchor holes....................................................................................................................................................................................................6Position the combined tilt bracket against the front of the support bracket so that the twoupper bolt holes and the single lower bolt hole on the tilt bracket are aligned with thebolts holes on the support bracket.Tilt anglepositioning gauge boltTilt anglepositioning gauge boltBracket anchor holesBracket anchor holesInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-83DRAFTDRAFT
...................................................................................................................................................................................................7From the tilt bracket side, screw in the two upper and one lower M6 bolts through theanchor holes on the tilt bracket and into the support bracket bolt holes....................................................................................................................................................................................................8Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................9Repeat the above procedure for attaching the second horizontal/vertical tilt bracket to theextension plate....................................................................................................................................................................................................10 Once the tilt brackets have been attached to the support plate the 9764 Metro Dock(s) canbe attached to the tilt brackets. Continue with “Attach 9764 Metro Dock to brackets”(p. 3-66).Attach 9764 Metro Dock to bracketsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following procedure to attach a pair of 9764 Metro Dock's directly to thesupport plate or to tilt brackets (attached to the support plate)....................................................................................................................................................................................................1Before attaching each 9764 Metro Dock ensure that the Metro Dock spacer is fitted and inplace on both 9764 Metro Dock's.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-84 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2Unscrew and remove the set of two upper M6 bolts and the one lower M6 bolt from theboth sides (left and right) of the support plate or if tilt brackets are attached from each ofthe tilt brackets....................................................................................................................................................................................................3Position a 9764 Metro Dock against the front of the bracket (support plate or tilt) so thatthe two upper bolt holes and the single lower bolt hole on the 9764 Metro Dock arealigned with the bolts holes on the bracket....................................................................................................................................................................................................4From the 9764 Metro Dock side, screw in the two M6 bolts back through the upper boltholes on the 9764 Metro Dock and into the upper bracket bolt holes.M5x12countersunk screwMetro Dockspacer9764 Metro Dock attachmentbolts on support plate9764 Metro Dock attachmentbolts on tilt bracketInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-85DRAFTDRAFT
Note: Ensure the bolts are positioned at the upper (or lower) part of the elongated holefor better contact area with the Metro Dock (the chamfered midsection of theelongated hole is used for banding installation)....................................................................................................................................................................................................5Move the 9764 Metro Dock metal slider to the “up” position as this allows easier accessto the lower attachment bolt hole:1. insert supplied key into lock2. turn the key to its hard stop position to unlock the slider3. push the slider upwards and turn the key to its hard stop position. The slider is nowlocked in the “up” position.Slider moves upwardsMetro Dock Slider(in down position)Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-86 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6From the 9764 Metro Dock side, screw in the single M6 bolts back through the lower bolthole on the 9764 Metro Dock and into the lower bracket bolt hole....................................................................................................................................................................................................7Using a 10 mm ratchet wrench, tighten the two upper and one lower M6 retaining bolts.Recommended screw torque; 7.0 N.m (62.0 lb.in)....................................................................................................................................................................................................8Finally move the 9764 Metro Dock metal slider to the “down” position:1. turn the key to its hard stop position to unlock the slider. The slider will automaticallyspring into the “down” position.2. turn the key to its hard stop position. The slider is now locked in the “down” positionand the key can be removed from the lock....................................................................................................................................................................................................9Repeat the above procedure for attaching the second 9764 Metro Dock to the other side ofthe support plate or, if tilt brackets are attached, to the second tilt bracket.Wall mount example (with tilt)The following figure shows an example of a 9764 Metro Dock pair configuration (withtilt brackets attached), mounted onto a wall or flat surface.Lower Metro Dockattachment boltInstallation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-87DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
How to continueAfter mounting the 9764 Metro Dock pair onto the double support bracket the cables needto be connected. Continue with the, “9764 Metro Dock cabling” (p. 3-89) chapter.Installation of the 9764 Metro Dock9764 Metro Dock installationProcedure 3-6: Wall mount the 9764 Metro Dock in a pairconfiguration........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-88 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
9764 Metro Dock cablingOverviewPurposeThis section provides instructions for routing and connecting the following cables to the9764 Metro Dock module:•Grounding cable•Ethernet cableNote: For outdoor NAR installations, or where local regulations dictate, the facility andpower cables are required to be routed to the equipment within rigid-steel or liquid-tightflexible metal conduit. As part of site preparation, the customer must provide the metalconduit and associated fittings for cable routes and connecting conduit to the outdoorequipment.ContentsProcedure 3-7: 9764 Metro Dock ground cabling 3-90Procedure 3-8: 9764 Metro Dock Ethernet cabling - fiber optic 3-92Procedure 3-9: 9764 Metro Dock Ethernet cabling - electrical 3-99Installation of the 9764 Metro Dock9764 Metro Dock cablingOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-89DRAFTDRAFT
Procedure 3-7: 9764 Metro Dock ground cablingPurposeThis topic describes the procedures to be followed when connecting the grounding cableto the 9764 Metro Dock.Important! The following must be observed:•This equipment must be externally grounded to an appropriate grounding systemusing: Yellow/Green 10 mm2insulated ground cable (required for Internationalmarkets) or 8 AWG ground cable (required for North America Regional markets).Grounding cable can be ordered from Alcatel-Lucent or be locally supplied.•All grounding system material (cable, connectors, etc.) must be of high quality, thatresist deterioration and require little or no maintenance.•Installation of the equipment must comply with local and national electrical codes andguidelines. If there is uncertainty that suitable grounding is available contact theappropriate site preparation contact or electrical inspection authority.Connect the ground cableTo attach the ground cable to the 9764 Metro Dock perform the following steps....................................................................................................................................................................................................1Route the ground cable from the site grounding system to the 9764 Metro Dock....................................................................................................................................................................................................2At the 9764 Metro Dock cut the ground cable to a proper length and strip the cable end toexpose approximately 20 mm (0.75 in)....................................................................................................................................................................................................3Place a double hole cable lug (with a holes suitable for M6 screws) onto the end of thecable. Using an appropriate crimping tool, crimp the lug onto the cable....................................................................................................................................................................................................4Clean the contact surface area of the cable lug and earthing point on the 9764 Metro Dockand use antioxidant to avoid oxidation.Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-7: 9764 Metro Dock ground cabling........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-90 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................5Place one washer (wave spring washer) on each terminal screw, align the grounding cablelug holes with the earthing terminal holes on the 9764 Metro Dock, and secure the cableto the grounding point using the terminal screws....................................................................................................................................................................................................6Secure grounding cable to the wall/pole.Important! The installation location (wall/pole) must be grounded in accordance withlocal regulatory guidelines...................................................................................................................................................................................................7Finally, crimp on a double cable lug at the other end of the ground cable and attach to themain grounding system.Bottom viewof Metro DockGreen/Yellowground cableGrounding pointon Metro DockInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-7: 9764 Metro Dock ground cabling........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-91DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 3-8: 9764 Metro Dock Ethernet cabling - fiber opticPurposeThis topic describes the procedures to be followed when connecting the optical Ethernetcable to the 9764 Metro Dock. The 9764 Metro Dock, may either be in a singleconfiguration, or daisy chained to a second 9764 Metro Dock.Cabling ancillary itemsThe following cabling related ancillary items can be ordered from Alcatel-Lucent whenthe backhaul infrastructure is configured for optical Ethernet:•SFP GBE 1000BaseLX SFP module (SM or MM). See “SFP modules” (p. 2-18).•Fiber Optic Ethernet cable with LC connector to optical SFP module at the 9764Metro Dock module. See “Ethernet cable - Optical” (p. 2-19).Install SFP transceiver moduleWARNINGLaser hazardUse of controls or adjustments or performance of procedures other than those specifiedherein may result in hazardous laser radiation exposure.Do not view directly into the laser beam with optical instruments such as a fibermicroscope because viewing of laser emission in excess of Class 1 limits significantlyincreases the risk of eye damage.Never look into the end of an exposed fiber or an open connector as long as the opticalsource is switched on.Ensure that the optical source is switched off before disconnecting optical fiberconnectors.NOTICEESD hazardSemiconductor devices can be damaged by electrostatic discharges (ESD)Follow the rules, outlined in the Safety chapter, see “Notices” (p. 1-7), for handlingmodules containing semiconductor components.Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-92 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Before the optical Ethernet cable can be connected, the SFP port(s) must be equippedwith the appropriate optical SFP transceiver. For backhaul, this can be either1000Base-SX multi mode or 1000Base-LX single mode, according to the networkspecifications.To install an SFP transceiver module into the 9764 Metro Dock module SFP port:...................................................................................................................................................................................................1Firstly, carry out the following to attach the ESD wrist strap:1. Attach the ESD strap over your wrist so that is in contact with your bare skin.2. Momentarily touch the ESD clip onto a bare (unpainted) metal spot so that any builtup static charge is dissipated.3. Attach the ESD clip to the 9764 Metro Dock ground lug screw (the ground lug screwcan be unscrewed slightly for easier ESD clip attachment)....................................................................................................................................................................................................2In order to remove the 9764 Metro Dock protective plate, ensure the Metro Dock metalslider is in the default “down” position. This allows easier access to all six of the plateretention screws....................................................................................................................................................................................................3On the front of the protective plate unscrew and safely store the6xM4plate retentionscrews (Hex wrench size, 2.5 mm).Carefully lift off the 9764 Metro Dock protective plate.ESD clip attachedbehind Metro Dockgrounding lug screwESD ground strapInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-93DRAFTDRAFT
...................................................................................................................................................................................................4Remove the SFP transceiver module(s) from their protective packaging.Important! Do not remove the SFP transceiver module dust plugs until directed to doso later in the procedure....................................................................................................................................................................................................5Check the label on the SFP transceiver module bodies to verify that you have the correctmodel for your network....................................................................................................................................................................................................6Insert SFP transceiver modules into SFP ports.If... Then... ViewYou are connecting a singlecable from the backhaul system.Align the backhaul optical SFPtransceiver module with the SFP portlabelled “BH 1” and insert themodule into the socket until you feelthe connector latch into place.You are connecting a daisychain cable in addition to thecable from the backhaul system.Align the daisy chain optical SFPtransceiver module with the SFP portlabelled “BH 2” and insert themodule into the socket until you feelthe connector latch into place.Attention: If the SFP module resists as you insert it, do not force it. Remove themodule, turn it over, and try reinserting.6xM4screwsMetro Dockprotective plateInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-94 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Push up and latch the SFP module locking bar into position to secure the SFP transceivermodule into the port....................................................................................................................................................................................................7To check that the SFP transceiver module(s) are seated and latched properly, grasp eachSFP module and try to remove it without releasing the latch.•If the SFP module can be removed, reinsert it until the module is latched securely intothe socket.•If the SFP module cannot be removed, it is installed and seated properly.Connect the Ethernet cableWARNINGLaser hazardUse of controls or adjustments or performance of procedures other than those specifiedherein may result in hazardous laser radiation exposure.Do not view directly into the laser beam with optical instruments such as a fibermicroscope because viewing of laser emission in excess of Class 1 limits significantlyincreases the risk of eye damage.Never look into the end of an exposed fiber or an open connector as long as the opticalsource is switched on.Ensure that the optical source is switched off before disconnecting optical fiberconnectors.To connect the optical Ethernet cable to the Alcatel-Lucent 9764 Metro Dock perform thefollowing steps:...................................................................................................................................................................................................1Route the optical Ethernet cable coming from the backhaul system to the 9764 MetroDock. If daisy chaining to a second 9764 MCO also route optical Ethernet cable to thisMCO....................................................................................................................................................................................................2Unscrew and remove the rounded compression nut from the cable gland located on thebottom of the 9764 Metro Dock casing, as shown in the following figure:Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-95DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................3Feed the compression gland assembly items onto the Ethernet cable (either single cable ordouble cable).If... Then... ViewYou are connecting a singlecable from the backhaulsystemFirstly remove the cableclamp from the optical cable,then in the following order,place the roundedcompression nut, the doubleslotted cable seal and thestrain relief onto the cable, asshown.StrainreliefCableclampCompressionnutCablesealYou are connecting a daisychain cable in addition to thecable from the backhaulsystemFirstly remove the cableclamp from both the opticalcables, then in the followingorder, place the roundedcompression nut, the doubleslotted cable seal and thestrain relief onto both cables,as shown.StrainreliefCableclampCompressionnutCableseal...................................................................................................................................................................................................4Feed the Ethernet cables through the gland opening on the Metro Dock and then insert thegland assembly into the gland housing.Note: The gland assembly with cable may need to be turned slightly in order to fullyslide into the gland housing before the compression nut can be screwed on.CompressionnutCompressiongland assemblyInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-96 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................5Replace the cable clamp onto the optical cable and within the 9764 Metro Dock casing,carefully route cables to the SFP cage.Remove dust plugs from the optical cable LC connectors and the SFP transceiver modulesand immediately insert the optical cable LC connectors into the SFP transceiver modules....................................................................................................................................................................................................6Screw the rounded compression nut back onto the main body of the gland. Use anadjustable or open-end wrench to tighten the compression nutImportant! It is recommended that the compression nut is torqued to 2.5 N.m (22.1lb.in) in order to create a watertight seal and avoid a potential loose connection....................................................................................................................................................................................................7Replace and reattach the 9764 Metro Dock protective plate via the six plate retentionscrews.Important! Ensure the plate gasket is seated correctly in the groove on the undersideof the plate. Tighten the six plate retention screws in the sequence shown.Recommended torque, 2.3 N.m (20.4 lb.in).Ethernet cableentry point(Cable gland)SFP cageEthernet cableconnection point(SFP Module)Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-97DRAFTDRAFT
...................................................................................................................................................................................................8Finally, secure the Ethernet cable to the wall/pole.Important! When securing cables ensure the following to avoid cable damage:•Secure cables with tie wraps. Use additional tie wraps wherever necessary forneatness•All cables should be run parallel with no twisting or tangled cables•Avoid excessive tension on the cable.How to continueAfter the grounding and Ethernet cable connections are completed:If... Then...The 9764 MCO module is to be installedat a later timecontinue with Procedure 3-10: “Final installationactivities and checks” (p. 3-112).A 9764 MCO Wi-Fi AP module is to beinstalled along with the 9764 MCOmodule immediately after Metro Dockinstallationcontinue with Appendix B, “Installation of the 9764MCO Wi-Fi AP”The 9764 MCO module is to be installedimmediately after Metro Dockinstallationcontinue with Chapter 4, “Installation of the 9764MCO module” before installing the 9764 MCOmodule.461352Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-8: 9764 Metro Dock Ethernet cabling - fiberoptic........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-98 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 3-9: 9764 Metro Dock Ethernet cabling - electricalPurposeThis topic provides the following procedures associated with connecting electricalEthernet cable to the 9764 Metro Dock:•SFP transceiver module installation.•Optional internal surge arrestor module installation.•Connection electrical backhaul Ethernet cable.Cabling ancillary itemsThe following Ethernet cabling related ancillary items are required when the backhaulinfrastructure is configured for electrical Ethernet:•10/100/1000BaseT Electrical SFP module. See “SFP modules” (p. 2-18).•Electrical Ethernet cable with RJ45 connector to electrical SFP module at the 9764Metro Dock module. See “Ethernet cable - Electrical” (p. 2-19).•Optional Ethernet surge arrestor (either external or internal)Can be installed if additional surge protection is required.Install SFP transceiver moduleNOTICEESD hazardSemiconductor devices can be damaged by electrostatic discharges (ESD)Follow the rules, outlined in the Safety chapter, see “Notices” (p. 1-7), for handlingmodules containing semiconductor components.To install SFP transceiver modules into the 9764 Metro Dock module SFP ports:...................................................................................................................................................................................................1Firstly, carry out the following to attach the ESD wrist strap:1. Attach the ESD strap over your wrist so that is in contact with your bare skin.2. Momentarily touch the ESD clip onto a bare (unpainted) metal spot so that any builtup static charge is dissipated.3. Attach the ESD clip to the 9764 Metro Dock ground lug screw (the ground lug screwcan be unscrewed slightly for easier ESD clip attachment).Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-99DRAFTDRAFT
...................................................................................................................................................................................................2Firstly ensure the Metro Dock metal slider is in the default “down” position as this allowseasier access to all six of the Metro Dock protective plate retention screws....................................................................................................................................................................................................3On the front of the protective plate unscrew the captive6xM4plate retention screws(Hex wrench size, 2.5 mm).Carefully lift off the 9764 Metro Dock protective plate....................................................................................................................................................................................................4Remove the SFP transceiver module(s) from the protective packaging....................................................................................................................................................................................................5Check the label on the SFP transceiver module body to verify that you have the correctmodel for your network.ESD clip attachedbehind Metro Dockgrounding lug screwESD ground strap6xM4screwsMetro Dockprotective plateInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-100 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6Insert SFP transceiver modules into SFP ports.If... Then... ViewYou are connecting a singlecable from the backhaul system.Align the backhaul electrical SFPtransceiver module with the SFP portlabelled “BH 1” and insert themodule into the socket until you feelthe connector latch into place.You are connecting a daisychain cable in addition to thecable from the backhaul system.Align the daisy chain optical SFPtransceiver module with the SFP portlabelled “BH 2” and insert themodule into the socket until you feelthe connector latch into place.Attention: If the SFP module resists as you insert it, do not force it. Remove themodule, turn it over, and try reinserting.Push up and latch the SFP module locking bar into position to secure the SFP transceivermodule into the port....................................................................................................................................................................................................7To check that SFP modules are seated and latched properly, grasp the SFP module and tryto remove it without releasing the latch.•If the SFP module can be removed, reinsert it until the module is latched securely intothe socket.•If the SFP module cannot be removed, it is installed and seated properly....................................................................................................................................................................................................8How to continue.If... Then...The internal surge arrestor module is tobe installed (available in ReleaseLR14.1.L)continue onto, “Install optional internal surgearrestor” (p. 3-102)No internal surge arrestor module isrequiredcontinue onto, “Connect the backhaul Ethernetcable” (p. 3-104)Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-101DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Install optional internal surge arrestorNOTICEESD hazardSemiconductor devices can be damaged by electrostatic discharges (ESD)Follow the rules, outlined in the Safety chapter, see “Notices” (p. 1-7), for handlingmodules containing semiconductor components.Follow these steps in order to install and cable the optional internal surge arrestor moduleinto the 9764 Metro Dock casing....................................................................................................................................................................................................1Within the 9764 Metro Dock casing remove the Metro Dock cable bar by unscrewing thetwo retaining screws....................................................................................................................................................................................................2From the surge arrestor kit packaging obtain the internal surge arrestor module and thethree T-10 Torx fixing screws....................................................................................................................................................................................................3Align the three screw holes on the surge arrestor module with the three screw holes withinthe 9764 Metro Dock casing and secure the module into place with the supplied T-10 Torxscrews.Tip: The three T-10 Torx screws are small, therefore it is recommended to use amagnetized Torx screwdriver.Cable barCable barscrewsInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-102 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Finally, using the short Ethernet cable (CA-SAEC) from the kit, plug one RJ45 cableconnector into the RJ45 port on the surge arrestor module and the other RJ45 cableconnector into the SFP transceiver located in port “BH1”....................................................................................................................................................................................................5Continue with the next procedure, “Connect the backhaul Ethernet cable” (p. 3-104)Surge arrestor moduleretaining screw(Torx T-10)Surge arrestor moduleSurge arrestor moduleretaining screw(Torx T-10)RJ45 connectionat SFPRJ45 connection atsurge arrestor moduleShort electricalethernet cableInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-103DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Connect the backhaul Ethernet cableFollow these step in order to connect the electrical Ethernet backhaul cable to the SFPmodule in the 9764 Metro Dock or the optional internal surge arrestor module (ifinstalled)....................................................................................................................................................................................................1Obtain, from the packaging, the Alcatel-Lucent electrical Ethernet cable. The RJ45connector without connector cover should be used at the 9764 Metro Dock side.Note: If an external surge arrestor is installed then use a short cable from the surgearrestor to the 9764 Metro Dock....................................................................................................................................................................................................2For increased cable connection within the cable gland, expose a section of screen braid(approximately 10 mm ) by cutting through the cable jacket. The exposed section shouldmeasured from the leading edge of the RJ45 connector to the center of the exposed area.If... Then...Cable connection isdirectly to SFP30 cm (+/- 5 mm)11.8 inches (+/- 0.2 inches)Exposed screen braidapprox. 10 mm (0.4 inches)Cable connection isto surge arrestormodule14 cm (+/- 5 mm)6 inches (+/- 0.2 inches)Exposed screen braidapprox. 10 mm (0.4 inches)...................................................................................................................................................................................................3Unscrew and remove the rounded compression nut from the cable gland located on thebottom of the 9764 Metro Dock casing, as shown in the following figure:Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-104 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Feed the compression gland assembly items onto the Ethernet cable (either single cable ordouble cable).If... Then... ViewYou are connecting a singlecable from the backhaulsystemIn the following order placethe rounded compression nut,the double slotted cable sealand the strain relief onto thecable, as shown.Strain reliefCompressionnutCablesealYou are connecting a daisychain cable in addition to thecable from the backhaulsystemFirstly remove the cableclamp from the optical cable,then in the following order,place the roundedcompression nut, the doubleslotted cable seal and thestrain relief onto both cables,as shown.Fibre cableclamp...................................................................................................................................................................................................5Pull the cable through the gland assembly parts until a connection is made between theexposed cable screen braid and the gland contact springs.CompressionnutCompressiongland assemblyInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-105DRAFTDRAFT
...................................................................................................................................................................................................6Feed the Ethernet cable(s) through the gland opening on the Metro Dock and looselyinsert the gland assembly into the gland housing.Note: The gland assembly with cable may need to be turned slightly in order to fullyslide into the gland housing before the compression nut can be screwed on....................................................................................................................................................................................................7Within the 9764 Metro Dock casing:•route the electrical (backhaul) cable to either the SFP transceiver (“BH1”) or, if theinternal surge arrestor is installed, to the connector on the surge arrestor module.Insert the Ethernet cable connector into the SFP transceiver or surge arrestor RJ45port.Ethernet cableContact springsCable glandContact springsInstallation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-106 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
•if daisy chaining to a second 9764 MCO, route the optical (daisy chain) cable to theSFP transceiver (“BH2”). Remove the dust plugs from the optical cable LCconnectors and the SFP transceiver module and immediately insert the LC connectorsinto the SFP transceiver.Optical daisy chainEthernet cableconnection point(at SFP)Optical daisy chainEthernet cable connection(no surge arrestor module)Optical daisy chainEthernet cable connection(with surge arrestor module)Optical daisy chainEthernet cableconnection point(at SFP)Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-107DRAFTDRAFT
...................................................................................................................................................................................................8Screw the rounded compression nut back onto the main body of the gland. Use anadjustable or open-end wrench to tighten the compression nut.Important! It is recommended that the compression nut is torqued to 2.5 N.m (22.1lb.in) in order to create a watertight seal and avoid a potential loose connection....................................................................................................................................................................................................9Replace and reattach the 9764 Metro Dock protective plate via the six plate retentionscrews.Important! Ensure the plate gasket is seated correctly in the groove on the undersideof the plate. Tighten the six plate retention screws in the sequence shown.Recommended torque, 2.3 N.m (20.4 lb.in)....................................................................................................................................................................................................10 Finally, secure the Ethernet cable to the wall/pole.Important! When securing cables ensure the following to avoid cable damage:•Secure cables with tie wraps. Use additional tie wraps wherever necessary forneatness•All cables should be run parallel with no twisting or tangled cables•Avoid excessive tension on the cable.461352Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-108 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Mount and cable the external surge arrestorFollow these steps to mount (either pole or wall) the optional external surge arrestor ontothe surge arrestor bracket and connect the Ethernet cables....................................................................................................................................................................................................1On the surge arrestor, unscrew the lower weatherized strain relief connector and lockingnut from the surge arrestor....................................................................................................................................................................................................2Site the surge arrestor onto the bracket so that the lower threaded Ethernet connectionpoint is positioned through the arrestor mounting hole....................................................................................................................................................................................................3Screw the arrestor locking nut back onto the arrestor and tighten so that the arrestor issecurely attached to the bracket....................................................................................................................................................................................................4Carefully feed the end of Ethernet cable coming from the Customer Network InterfaceDevice through the previously unscrewed lower strain relief connector....................................................................................................................................................................................................5Plug the Ethernet cable RJ45 connector into the lower connector on the arrestor. Screwthe weatherized strain relief connector back onto the arrestor and tighten....................................................................................................................................................................................................6At the top of the arrestor, unscrew the upper weatherized strain relief connector from thesurge arrestor....................................................................................................................................................................................................7Carefully feed the end of Ethernet cable coming from the 9764 Metro Dock through theupper strain relief connector....................................................................................................................................................................................................8Plug the Ethernet cable RJ45 connector into the upper connector on the arrestor. Screwthe weatherized strain relief connector back onto the arrestor and tighten....................................................................................................................................................................................................9Finally, secure the Ethernet cable to the wall/pole.Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-109DRAFTDRAFT
Important! When securing cables ensure the following to avoid cable damage:•Secure cables with tie wraps. Use additional tie wraps wherever necessary forneatness•All cables should be run parallel with no twisting or tangled cables•Avoid excessive tension on the cable.How to continueAfter the grounding and Ethernet cable connections are completed:If... Then...The 9764 MCO module is to be installedat a later timecontinue with Procedure 3-10: “Final installationactivities and checks” (p. 3-112).A 9764 MCO Wi-Fi AP module is to beinstalled along with the 9764 MCOmodule immediately after Metro Dockinstallationcontinue with Appendix B, “Installation of the 9764MCO Wi-Fi AP”The 9764 MCO module is to be installedimmediately after Metro Dockinstallationcontinue with Chapter 4, “Installation of the 9764MCO module” before installing the 9764 MCOmodule.Installation of the 9764 Metro Dock9764 Metro Dock cablingProcedure 3-9: 9764 Metro Dock Ethernet cabling -electrical........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-110 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
9764 Metro Dock post-installationOverviewPurposeThis section provides post-installation information and activities that should be carriedout after the Alcatel-Lucent 9764 Metro Dock has been installed.ContentsProcedure 3-10: Final installation activities and checks 3-112Installation of the 9764 Metro Dock9764 Metro Dock post-installationOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-111DRAFTDRAFT
Procedure 3-10: Final installation activities and checksOverviewThis topic describes the final 9764 Metro Dock installation activities and checks to becarried out if the 9764 MCO module is to be connected at a later time.9764 Metro Dock plate and connection coversIf the 9764 MCO module is to be connected at a later time ensure that the following are inplace in order to protect the 9764 Metro Dock against the elements.•The 9764 Metro Dock is fitted with its weatherized plate•The 9764 MCO module connector is fitted with its gasket and blanking plate.Final installation checksBefore leaving the installation site, check the following:...................................................................................................................................................................................................1Check the overall installation. Verify that mounted equipment is secure and that nounintentional mechanical alteration has occurred to either the equipment itself or theinstallation infrastructure....................................................................................................................................................................................................2Ensure all the exterior connections are secure....................................................................................................................................................................................................3Ensure all cables are secured along their routes.Metro Dockweatherized plateMetro Cell Moduleconnector gasket andblanking plateInstallation of the 9764 Metro Dock9764 Metro Dock post-installationProcedure 3-10: Final installation activities and checks........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-112 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Finally, inspect the site for loose tools, materials, and parts. Remove all such loose tools,materials, and parts.Installation of the 9764 Metro Dock9764 Metro Dock post-installationProcedure 3-10: Final installation activities and checks........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 3-113DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Installation of the 9764 Metro Dock Procedure 3-10: Final installation activities and checks........................................................................................................................................................................................................................................................................................................................................................................................................................................................................3-114 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
44Installation of the 9764MCO moduleOverviewPurposeThis chapter provides instructions for installing the Alcatel-Lucent 9764 Metro CellOutdoor module.Contents9764 MCO pre-installation 4-2Pre-installation information 4-39764 MCO cabling 4-4Procedure 4-1: Connect external RF antenna to the Alcatel-Lucent 9764 MCOLTE 2x2W4-5Procedure 4-2: Connect GPS antenna 4-7Procedure 4-3: 9764 MCO module ground cabling 4-18Site power requirements (AC) 4-21Site power requirements (DC) 4-24Product power requirements 4-27Procedure 4-4: Connect power cable 4-299764 MCO installation 4-40Procedure 4-5: Attach 9764 MCO module to 9764 Metro Dock 4-41Procedure 4-6: Orient 9764 MCO module 4-489764 MCO post-installation 4-50Procedure 4-7: Post installation activities 4-51Procedure 4-8: Power on the 9764 MCO 4-52...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-1DRAFTDRAFT
9764 MCO pre-installationOverviewPurposeThis section provides pre-installation information and lists tools and materials required toinstall the Alcatel-Lucent 9764 Metro Cell Outdoor.ContentsPre-installation information 4-3Installation of the 9764 MCO module9764 MCO pre-installationOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Pre-installation informationProduct delivery contentsThe following items are supplied with the 9764 MCO module:•The 9764 MCO moduleVariable parts and ancillary itemsIn addition to the standard delivered parts, the following variable and ancillary items areavailable:•Molex 1212010001 AC power connector•Molex 1212060025 DC power connector•Power supply cable (100 m roll)Installation tools requiredThe following tools may be used during installation:•Pliers•Screwdrivers (power and/or manual):– Phillips (flat blade)– Torx (T-25 and T-40)•Assorted cable tiesWi-Fi AP installationIf you intend to attach an Alcatel-Lucent 9764 Metro Cell Outdoor Wi-Fi AP to the 9764MCO module, attach it before you attach the 9764 MCO module to the 9764 Metro Dock.For instructions, refer to Appendix B, “Installation of the 9764 MCO Wi-Fi AP”Installation of the 9764 MCO module9764 MCO pre-installationPre-installation information........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-3DRAFTDRAFT
9764 MCO cablingOverviewPurposeThis section provides instructions for routing and connecting the following cables to theAlcatel-Lucent 9764 Metro Cell Outdoor module:•RF antenna cables for 9764 MCO V1.1 B2 LTE 2x2W model•GPS antenna cable•Ground cable•Power cableThe Alcatel-Lucent 9764 MCO LTE 2x1W and Alcatel-Lucent 9764 Metro CellOutdoor LTE 2x2W have AC and DC powered variants. You must ensure that youfollow the correct power requirements and cabling procedure for the variant you have.Note: For outdoor NAR installations, or where local regulations dictate, the facility andpower cables are required to be routed to the equipment within rigid metal conduit (RMC)or liquid-tight flexible metal (LTFMC) conduit. As part of site preparation, the customermust provide the metal conduit and associated fittings for cable routes and connectingconduit to the outdoor equipment.Alternatively, an allowable outdoor armored cable described in the National ElectricalCode and Canadian Electrical Code, Part I, may be used without a conduit.Cable types that may be used without a conduit include:•Type MC cable, such as Hybriflex cable•Outdoor tray cable Type TC-ERContentsProcedure 4-1: Connect external RF antenna to the Alcatel-Lucent 9764 MCOLTE 2x2W4-5Procedure 4-2: Connect GPS antenna 4-7Procedure 4-3: 9764 MCO module ground cabling 4-18Site power requirements (AC) 4-21Site power requirements (DC) 4-24Product power requirements 4-27Procedure 4-4: Connect power cable 4-29Installation of the 9764 MCO module9764 MCO cablingOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 4-1: Connect external RF antenna to theAlcatel-Lucent 9764 MCO LTE 2x2WPurposeThis procedure describes how to connect the external duplex RF antenna to anAlcatel-Lucent 9764 MCO LTE 2x2W module.ProcedureTo connect the RF cables:...................................................................................................................................................................................................1Refer to the RF antenna mounting instructions included with the RF antenna kit for thesteps to mount the antenna....................................................................................................................................................................................................2Locate the external RF antenna connectors (RX/TX) at the top of the heat sink side of the9764 MCO module and remove the protective caps if present....................................................................................................................................................................................................3Connect the external RF antenna adapter cables to the corresponding QN connectors onthe back of the 9764 MCO module.QN - Quick NRX/TX antennaInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-1: Connect external RF antenna to theAlcatel-Lucent 9764 MCO LTE 2x2W........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-5DRAFTDRAFT
Installation of the 9764 MCO module9764 MCO cablingProcedure 4-1: Connect external RF antenna to theAlcatel-Lucent 9764 MCO LTE 2x2W........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 4-2: Connect GPS antennaPurpose'For an MCO with 2 GPS antenna connectors, use this procedure to connect an externalGPS antenna cable to the 9764 MCO.MCOs with 2 GPS antenna connectors are supplied with an internal GPS antenna, andwith a bridging cable connected between the internal and external GPS antennaconnectors. For these MCOs, use this procedure to verify that the bridging cable iscorrectly connected, or to connect the internal or external GPS antenna.For a Alcatel-Lucent 9764 MCO LTE 2x2W, use this procedure to connect an externalantenna or switch between the internal and external antennas.Note: The internal GPS antenna solution is not supported on the 9764 MCO V1.1 B7LTE 2x1W, 9764 MCO V1.1 B2 LTE 2x1W and 9764 MCO V1.0 B25 LTE 2x1Wmodels.External GPS antennaThe following figure shows the external GPS antenna and its mounting kit.Figure 4-1 External GPS antenna configurationGPS antennamounting kitExternal GPS antennaGPS antenna cableGPS adapter cable9764 MCOInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-7DRAFTDRAFT
Two different external GPS antennas are available. The 26 dB gain GPS antenna is usedwhen antenna cable loss is less than 10 dB at 1575 MHz. For antenna cable loss greaterthan 10 dB at 1575 MHz, the 40 dB gain antenna must be used.Before you beginEnsure that the following tools are available:•Adjustable (crescent) wrenches•Torque ratchet (socket wrench)•Items such as crimping tools that are appropriate for attaching a new cable connectorto the GPS cable•Protective eye wearImportant! Do not mount the GPS antenna within 10 feet (3 m) of any transmitantenna.Safety statementsWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.NOTICEESD hazardSemiconductor devices can be damaged by electrostatic discharges (ESD)Follow the rules, outlined in the Safety chapter, see “Notices” (p. 1-7), for handlingmodules containing semiconductor components.These admonishments apply throughout this procedure. Refer to the Safety statementschapter for general safety information.Connect GPS antenna...................................................................................................................................................................................................1If... Then...You are connecting an external GPS antennato an MCO with 1 GPS antenna connectorFollow procedure “Connect external GPSantenna - B25, B7 or B2 MCO” (p. 4-9)Installation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
If... Then...You are connecting an external GPS antennato an MCO with 2 GPS antenna connectorsFollow procedure “Connect external GPSantenna to MCO - B3 MCO” (p. 4-12)You are verifying or connecting the internalGPS antenna to an MCO with 2 GPS antennaconnectorsFollow procedure “Connect internal GPSantenna to MCO” (p. 4-14)You are connecting a GPS antenna to theAlcatel-Lucent 9764 MCO LTE 2x2WFollow the procedure “Connectinternal/external GPS antenna toAlcatel-Lucent 9764 MCO LTE 2x2W”(p. 4-15)Note: The internal GPS antenna solution is not supported on the 9764 MCO V1.1 B7LTE 2x1W, 9764 MCO V1.1 B2 LTE 2x1W and 9764 MCO V1.0 B25 LTE 2x1Wmodels.Connect external GPS antenna - B25, B7 or B2 MCO...................................................................................................................................................................................................1Refer to the GPS antenna mounting instructions included with the GPS antenna kit for thesteps to mount the antenna....................................................................................................................................................................................................2Locate the GPS antenna connection on the back of the 9764 MCO module and removethe protective cap if one is present.Installation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-9DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................3Connect the GPS adapter cable by pushing the adapter cable connector onto the 9764MCO module QMA-type connector until it clicks into place.Figure 4-2 External GPS antenna connectorConnector for optionalexternal GPS antennaFigure 4-3 GPS antenna connectionInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Apply weatherproof tape to the cable connectors as follows (see figure below for tapeplacement):•For B25 MCO, B2 MCO and B2/B25 MCO, apply one layer of new weatherprooftape to the cable connections.•For B3 MCO and B7 MCO, apply linerless rubber splicing tape first to the cableconnections, then cover with vinyl electrical tape (vinyl tape over rubber tape).Figure 4-4 Weatherproof tape placement for external GPS antennaInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-11DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Connect external GPS antenna to MCO - B3 MCO...................................................................................................................................................................................................1Refer to the GPS antenna mounting instructions included with the GPS antenna kit for thesteps to mount the antenna....................................................................................................................................................................................................2Locate the internal and external GPS antenna connectors, that are on the top part of theheatsink side of the 9764 MCO module....................................................................................................................................................................................................3Disconnect and remove the bridging cable that connects the two internal and externalGPS antenna connectors....................................................................................................................................................................................................4Place a protective cap on the right hand QMA-type connector (looking at the 9764 MCOmodule from the heatsink side)....................................................................................................................................................................................................5Connect the external GPS adapter cable (coming from the external GPS antenna) to theexternal GPS connector (left hand QMA-type connector when looking at the 9764 MCOmodule from the heatsink side), by pushing the adapter cable connector onto the 9764MCO module QMA-type connector until it clicks into place.Figure 4-5 Internal and external GPS antenna connectorsExternal GPSantennaconnectorInternal GPSantennaconnectorInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-12 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................6Apply weatherproof tape to the cable connectors as follows (see figure below for tapeplacement):•For B25 MCO, B2 MCO and B2/B25 MCO, apply one layer of weatherproof tape tothe cable connections.•For B3 MCO and B7 MCO, apply linerless rubber splicing tape first to the cableconnections, then cover with vinyl electrical tape (vinyl tape over rubber tape).Figure 4-6 GPS antenna connectionInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-13DRAFTDRAFT
Connect internal GPS antenna to MCONote: The internal GPS antenna solution is not supported on the 9764 MCO V1.1 B7LTE 2x1W, 9764 MCO V1.1 B2 LTE 2x1W and 9764 MCO V1.0 B25 LTE 2x1Wmodels....................................................................................................................................................................................................1Verify that a bridge cable is connected to both GPS connectors as shown in the followingfigure:Figure 4-7 Weatherproof tape placement for external GPS antennaInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-14 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................2If a bridge cable is not connected to the GPS connectors, then connect a bridge cable toboth GPS connectors by pushing the bridge cable connector onto each 9764 MCO moduleQMA-type connector until it clicks into place.Connect internal/external GPS antenna to Alcatel-Lucent 9764 MCO LTE 2x2W...................................................................................................................................................................................................1Refer to the GPS antenna mounting instructions included with the GPS antenna kit for thesteps to mount the antenna....................................................................................................................................................................................................2Locate the GPS antenna connector on the back of the 9764 MCO module.Figure 4-8 Bridge cable between external and internal GPS antenna connectorsInternal GPSconnectorExternal GPSconnectorInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-15DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................3The internal GPS antenna is by default connected. If an external GPS antenna is needed,connect the external GPS adapter cable (coming from the external GPS antenna) to theQMA GPS antenna switch connector, by pushing the adapter cable connector onto the9764 MCO module QMA-type connector until it clicks into place....................................................................................................................................................................................................4In case an external GPS is used, apply weatherproof tape to the cable connectors asfollows (see figure below for tape placement):•For B25 MCO, B2 MCO and B2/B25 MCO, apply one layer of weatherproof tape tothe cable connections.•For B3 MCO and B7 MCO, apply linerless rubber splicing tape first to the cableconnections, then cover with vinyl electrical tape (vinyl tape over rubber tape).Figure 4-9 Internal/external GPS antenna connectorQMA - Quick SMAGPS antenna switchInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-16 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Figure 4-10 Weatherproof tape placement for external GPS antennaInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-2: Connect GPS antenna........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-17DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 4-3: 9764 MCO module ground cablingPurposeThis topic describes the procedures to be followed for grounding the 9764 MCO module.Note:•Grounding of the 9764 MCO module is carried out via bonding from the 9764Metro Dock module using the ground cable and materials (screws and washers)contained in the Basic Installation Kit.•Grounding of the equipment must comply with local and national electrical codesand guidelines. If there is uncertainty that suitable grounding is available contactthe appropriate site preparation personnel or electrical inspection authority.Connect the ground cableTo carry out grounding of the 9764 MCO module from the 9764 Metro Dock moduleperform the following steps....................................................................................................................................................................................................1Ensure that the power is off before proceeding with the ground cable connection....................................................................................................................................................................................................2Acquire the short 4mm2(12 AWG) grounding cable, M6 terminal screw and M6 washersfrom the basic installation kit....................................................................................................................................................................................................3Clean the contact surface area of the M6 lug ring at one of the short ground cable andgrounding point on the 9764 Metro Dock. Use antioxidant to avoid oxidation....................................................................................................................................................................................................4Thread the supplied washer then the lock washer onto the M6 terminal screw.Align the cable lug ring with the 9764 Metro Dock single terminal hole and secure thecable to the grounding point using the terminal screw.Installation of the 9764 MCO module9764 MCO cablingProcedure 4-3: 9764 MCO module ground cabling........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-18 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................5Carry out the following:Action: Refer to:Connect the power cable to the9764 MCO moduleProcedure 4-4: “Connect power cable” (p. 4-29)Attach the 9764 MCO module tothe 9764 Metro Dock moduleProcedure 4-5: “Attach 9764 MCO module to 9764 MetroDock” (p. 4-41)...................................................................................................................................................................................................6Finally, from the underside of the 9764 MCO module secure the ground cable connectoronto the cable connector tab on the 9764 MCO module.Single holeground point(Metro Dock)1 Hexagon Socketscrew M6x10Ground cable4 mm (12 AWG)22 Washers M6Note: .The short ground cable is green/yellow, however the cable may be black in some older installation kitsFaston tab (M5)connector onMCO ModuleGround cableconnection onMCO ModuleGround cableconnection onMetro DockInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-3: 9764 MCO module ground cabling........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-19DRAFTDRAFT
Installation of the 9764 MCO module9764 MCO cablingProcedure 4-3: 9764 MCO module ground cabling........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-20 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Site power requirements (AC)PurposeThis section describes the power and grounding requirements that must be consideredwhen planning site facilities for Alcatel-Lucent installed equipment and products.General requirementsAll power and grounding system wiring, short-circuit (over-current) protection and surgeprotection devices must be installed by the appropriately licensed personnel. Installationmust be performed in accordance with national and local electrical codes, for example:•In the United States:National Electrical Code, NFPA 70•In Canada:Canadian Electrical Code, part I, CSA C22.1•In other countries:International Electrotechnical Commission (IEC) 60364, parts 1 through 7In addition, adherence to all additional requirements mandated by the “country of use” isthe customer's responsibility.The appropriate power supply ground connections and site equipment ground connectionsmust be in place before commercial AC power service can be connected to the equipmentinstalled at the site.Customer AC power supplyThe equipment installed on site must be supported with a customer supplied AC powerservice. The AC connection point should be easily accessible by the service team and bemarked as the disconnect device of the equipment.Note:•The service board (or load center), circuit breakers and surge protectors devicesare not supplied with the product. They must be ordered and installed as part ofsite preparation by the customer.•All wiring (including grounding) and over-current protection must be installed atthe service panel by suitably trained and licensed personnel and in accordancewith the national and local electrical codes.•An appropriate earth ground connection is required before commercial powerservice can be connected to any equipment at the site.In the United States and Canada, the branch circuit breaker shall be installed inaccordance with the National Electrical Code, or the Canadian Electrical Code, Part I.Installation of the 9764 MCO module9764 MCO cablingSite power requirements (AC)........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-21DRAFTDRAFT
The branch circuit breaker should always be situated upstream of the equipment and mustbe a double pole 20A Type C disconnect device.Line surge protectionA surge protection device is not supplied with the product. It must be ordered andinstalled as part of site preparation by the customer.The equipment can be connected to an AC mains distribution system classified as CAT II(equipment dedicated for connection to the mains distributed within a building). If thecategory of the AC mains is higher than CAT II (III or IV), then upstream surge protectionmust be installed by the customer to reduce the voltage range of transients in accordancewith CAT II.Power source Over-voltage categoryEquipment connected to building mains CAT IIEquipment connected directly to low voltage mains CAT III or CAT IVThe installation wiring for all outdoor AC units must be provided with a Listed/Approvedsurge protection device. In the United States and Canada the installation must be inaccordance with the National Electrical Code or the Canadian Electrical Code, Part I.Power junction boxFor outdoor installations, in countries where local regulations dictate, a customer-suppliedpower junction box, or a mating plug and receptacle, may need to be installed as part ofsite preparation. As part of site preparation, the customer must provide the appropriatejunction box and associated fittings.In the United States and Canada, outdoor cord pendants, if used, shall comply with NECArticle 400 or Canadian Electrical Code, Part I Rule 4-0129764Metro CellOutdoor9764Metro CellOutdoor20A20APower cable 3G1.5mm 2Power cable 3G1.5mm 2Main AC powerCircuit breaker(double pole Type C)Circuit breaker(double pole Type C)Installation of the 9764 MCO module9764 MCO cablingSite power requirements (AC)........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-22 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Conduit requirementsFor outdoor installations, in countries where local regulations dictate, the power cablesare required to be routed to the equipment within rigid metal conduit (RMC) orliquid-tight flexible metal (LTFMC) conduit. As part of site preparation, the customermust provide the metal conduit and associated fittings for cable routes and connectingconduit to the outdoor equipment.Alternatively, an allowable outdoor armored cable described in the National ElectricalCode and Canadian Electrical Code, Part I, may be used without a conduit.Cable types that may be used without a conduit include:•Type MC cable, such as Hybriflex cable•Outdoor tray cable Type TC-ER9764Metro CellOutdoorPanelboardPower cablePower connector atthe Metro Cell OutdoorPowerjunction boxLocally suppliedPower cable3G1.5mm 2Site poweroutletMainssupplyInstallation of the 9764 MCO module9764 MCO cablingSite power requirements (AC)........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-23DRAFTDRAFT
Site power requirements (DC)PurposeThis section describes the power and grounding requirements that must be consideredwhen planning site facilities for Alcatel-Lucent installed equipment and products.General requirementsAll power and grounding system wiring, short-circuit (over-current) protection and surgeprotection devices must be installed by the appropriately licensed personnel. Installationmust be performed in accordance with national and local electrical codes, for example:•In the United States:United States National Fire Protection Association (NFPA) 70 and United StatesNational Electrical Code (NEC)•In Canada:Canadian Electrical Code, part I, CSA C22.1•In other countries:International Electrotechnical Commission (IEC) 60364, parts 1 through 7In addition, adherence to all additional requirements mandated by the “country of use” isthe customer's responsibility.The appropriate power supply ground connections and site equipment ground connectionsmust be in place before commercial AC power service can be connected to the equipmentinstalled at the site.Customer DC power supplyThe equipment installed on site must be supported with a customer supplied nominal-48V DC power service. The DC connection point should be easily accessible by theservice team and be marked as the disconnect device of the equipment.Note:•The service board (or load center), circuit breakers and surge protectors devicesare not supplied with the product. They must be ordered and installed as part ofsite preparation by the customer.•All wiring (including grounding) and over-current protection must be installed atthe service panel by suitably trained and licensed personnel and in accordancewith the national and local electrical codes.•An appropriate earth ground connection is required before commercial powerservice can be connected to any equipment at the site.Installation of the 9764 MCO module9764 MCO cablingSite power requirements (DC)........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-24 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
The branch circuit breaker should always be situated upstream of the equipment and mustbe a double pole 20A Type C disconnect device.Line surge protectionA surge protection device is not supplied with the product. It must be ordered andinstalled as part of site preparation by the customer.Power junction boxFor outdoor installations, in countries where local regulations dictate, a customer suppliedpower junction box may need to be installed as part of site preparation. As part of sitepreparation, the customer must provide the appropriate junction box and associatedfittings.In the United States and Canada, outdoor cord pendants, if used, shall comply with NECArticle 400 or Canadian Electrical Code, Part I Rule 4-012.Conduit requirementsFor outdoor installations, in countries where local regulations dictate, the power cablesare required to be routed to the equipment within rigid metal conduit (RMC) orliquid-tight flexible metal (LTFMC) conduit. As part of site preparation, the customermust provide the metal conduit and associated fittings for cable routes and connectingconduit to the outdoor equipment.9764Metro CellOutdoor9764Metro CellOutdoor Power cable 3G1.5mm 220A20APower cable 3G1.5mm 2Main DC power(-48V)Circuit breaker(double pole Type C)Circuit breaker(double pole Type C)9764Metro CellOutdoorPanelboardPower cablePower connector atthe Metro Cell OutdoorPowerjunction boxLocally suppliedPower cable3G1.5mm 2Site poweroutletMainssupplyInstallation of the 9764 MCO module9764 MCO cablingSite power requirements (DC)........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-25DRAFTDRAFT
Alternatively, an allowable outdoor armored cable described in the National ElectricalCode and Canadian Electrical Code, Part I, may be used without a conduit.Cable types that may be used without a conduit include:•Type MC cable, such as Hybriflex cable•Outdoor tray cable Type TC-ERInstallation of the 9764 MCO module9764 MCO cablingSite power requirements (DC)........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-26 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Product power requirementsProduct power dataThe following table provides power related information applicable to the Alcatel-Lucent9764 MCO LTE 2x1W and the Alcatel-Lucent 9764 MCO LTE 2x2WPower supplyAC Electrical Rating 100V-110 V AC, 200-230 V AC,single phase, 2 A, 50/60 HzDC Electrical Rating -48 V DC, 3.5 A, powered fromSELV sourceEarthing systemSupported earthing systems TT or TNUnsupported earthing systems ITPower consumptionGigabit Ethernet backhaul (Without 9764 MCO Wi-FiAP module)< 34WGigabit Ethernet backhaul (With 9764 MCO Wi-Fi APmodule)< 42WPower ancillary itemsThe following Alcatel-Lucent power related ancillary items must be used. Refer to the9764 lightRadio Metro Cell Outdoor “Family” Model Offer Provisioning Guide,BCR/IRC/APP/038681Table 4-1 Power materialsItem Description UsePower connector (AC) AC power connectorCable diameter8–9mmConductor cross-section: 1.5 mm2Approval according to EN50525-3-21Required for 9764 MCO module with ACpower (International markets)Power connector (DC) DC power connector Required for 9764 MCO module with DCpower (International markets)Installation of the 9764 MCO module9764 MCO cablingProduct power requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-27DRAFTDRAFT
Table 4-1 Power materials (continued)Item Description UsePower cable Power cable IN/OUT 3G1,5mm²,100m roll or multiples of 1m length(as needed)Required for 9764 MCO module(International markets)Power cable (AC) Power cable pre-assembled with ACpower connector, various lengths(2m. 4.5m, 9m, 12m)Required for 9764 MCO module with ACpower (North America Regional markets)Power cable (DC) Power cable pre-assembled with DCpower connector, various lengths(2m. 4.5m, 9m, 12m)Required for 9764 MCO module with DCpower (North America Regional markets)Power connection pointPower is supplied to the 9764 MCO module, the 9764 Metro Dock module and theoptional 9764 MCO Wi-Fi AP module via either an AC or DC connector on the reverseside of the 9764 MCO module.Power connectionpoint9764 MCO module(reverse view)Installation of the 9764 MCO module9764 MCO cablingProduct power requirements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-28 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 4-4: Connect power cablePurposeThis topic describes the procedures to be followed when connecting the power cable tothe 9764 MCO module.ConnectionsThe following figure shows the connection interfaces of the 9764 MCO module:Before you beginYou must connect the power cable to the 9764 MCO module before you attach the 9764MCO module to the 9764 Metro Dock, otherwise you will not be able to access the ACpower connector on the 9764 MCO module.Depending on whether your 9764 MCO requires AC or DC power, and whether you havea pre-assembled power cord or you need to assemble the power cord, select theappropriate procedure from the following table:If... Then follow this procedureyour MCO requires AC power and youneed to assemble the power cable“Assemble AC power cable onto connector”(p. 4-30)your MCO requires AC power and youneed to use a pre-assembled power cord“Connect AC power cord” (p. 4-33)your MCO requires DC power and youneed to assemble the power cable“Assemble DC power cable onto connector”(p. 4-34)your MCO requires DC power and youneed to use a pre-assembled power cord“Connect DC power cord” (p. 4-38)Figure 4-11 connection interfacesPower connectorInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-29DRAFTDRAFT
In the United States and Canada, outdoor cords, whether installed as cord pendants orwith mating plug/receptacles, shall comply with NEC Article 400 or Canadian ElectricalCode, Part I Rule 4-012.Assemble AC power cable onto connectorDANGERElectric-shock hazardSince the 9764 MCO operates on 120-220 V AC, the risk of serious injury or death fromelectrocution exists throughout this procedure.Follow the first step of this procedure carefully and completely.WARNINGElectric-shock hazardThe current to the unit must be limited by an external fuse or circuit breaker incorporatedin the fixed wiring. The fuse or circuit breaker can be used as a disconnect device to turnoff the power to the system.Ensure that the system power is off and that power cables are safe to handle before youproceed with this procedure.WARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Use this procedure if you have a separate AC power connector and cable....................................................................................................................................................................................................1Ensure that the power that feeds the AC power cable to the 9764 MCO is OFF, and blockaccess so that no one can restore power to that cable during this procedure....................................................................................................................................................................................................2Cut the power cable to the required length....................................................................................................................................................................................................3Disassemble the cover assembly of the power connector. See the following figure:Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-30 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................4Feed the cable through the cable opening in the cover of the power connector and outthrough the bottom of the cover....................................................................................................................................................................................................5Strip the cable according to the dimensions in the figure below. Assuming an H12 groundposition, the longest wire is the ground wire....................................................................................................................................................................................................6Crimp the exposed cable conductor with 8 mm ferrules, as shown in the following figure:Side view of connectorTop view of connectorwith cover removedRegistration tabTerminals}Nut30 mm screwwith gasketCover40 mm (1.6 in)8mm(0.32 in)8mm(0.32 in)8mm(0.32 in)30 mm (1.2 in)30 mm (1.2 in)BrownBlueGreen/yellowInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-31DRAFTDRAFT
...................................................................................................................................................................................................7Cut the exposed ends of the cable to the length of the pins in the connector, as shown inthe following figure:...................................................................................................................................................................................................8Screw the wires into the terminal blocks to a torque of 0.4 Nm.Attention: Ensure that you connect the Live, Neutral, and Ground wires to the correctpins as shown in the following figure:Crimping lugs (ferrules)Cut conductorsto length4 mm (0.157 in)4 mm (0.157 in)4 mm (0.157 in)Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-32 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................9Insert the connector assembly into the cover (with the correct ground position) and pullthe excess cable back out through the cable opening of the connector cover....................................................................................................................................................................................................10 Ensure that the cable gasket is correctly seated, and tighten the nut to a torque of 1 Nm(0.737 lb-ft)....................................................................................................................................................................................................11 Attach the gasket and insert the fixing screw....................................................................................................................................................................................................12 Plug the AC power connector into the power connector on the bottom left of the 9764MCO module....................................................................................................................................................................................................13 Fix the AC power connector in position by tightening the screw on the AC powerconnector. Using a screwdriver with a Phillips head, torque to 0.4 Nm (0.295 lb ft).Connect AC power cordDANGERElectric-shock hazardSince the 9764 MCO operates on 120-220 V AC, the risk of serious injury or death fromelectrocution exists throughout this procedure.Follow the first step of this procedure carefully and completely.GroundPin 1:Brown, Live Pin 2:Blue, NeutralRegistrationtabTop view of connectorwith cover removedInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-33DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
WARNINGElectric-shock hazardThe current to the unit must be limited by an external fuse or circuit breaker incorporatedin the fixed wiring. The fuse or circuit breaker can be used as a disconnect device to turnoff the power to the system.Ensure that the system power is off and that power cables are safe to handle before youproceed with this procedure.WARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Use this procedure if you have a pre-assembled AC power cord....................................................................................................................................................................................................1Ensure that the power that feeds the AC power cable to the 9764 MCO is OFF, and blockaccess so that no one can restore power to that cable during this procedure....................................................................................................................................................................................................2Plug the AC power connector on the power cord into the power connector on the bottomleft of the 9764 MCO module....................................................................................................................................................................................................3Fix the AC power connector in position by tightening the screw on the AC powerconnector. Using a screwdriver with a Phillips head, torque to 0.4 Nm (0.295 lb ft).Assemble DC power cable onto connectorDANGERElectric-shock hazardSince the 9764 MCO operates on DC power, the risk of serious injury or death fromelectrocution exists throughout this procedure.Follow the first step of this procedure carefully and completely.Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-34 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
WARNINGElectric-shock hazardThe current to the unit must be limited by an external fuse or circuit breaker incorporatedin the fixed wiring. The fuse or circuit breaker can be used as a disconnect device to turnoff the power to the system.Ensure that the system power is off and that power cables are safe to handle before youproceed with this procedure.WARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Use this procedure if you have a separate DC power connector and cable....................................................................................................................................................................................................1Ensure that the power that feeds the DC power cable to the 9764 MCO is OFF, and blockaccess so that no one can restore power to that cable during this procedure....................................................................................................................................................................................................2Cut the power cable to the required length....................................................................................................................................................................................................3Disassemble the cover assembly of the power connector. See the following figure:Nut32 mm screwwith gasketTop view of connectorTop view of connectorwith cover removedTerminals}Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-35DRAFTDRAFT
...................................................................................................................................................................................................4Feed the cable through the cable opening in the cover of the power connector and outthrough the bottom of the cover....................................................................................................................................................................................................5Strip the cable according to the dimensions in the figure below. Assuming an H12 groundposition, the longest wire is the ground wire....................................................................................................................................................................................................6Crimp the exposed cable conductor with 8 mm ferrules, as shown in the following figure:...................................................................................................................................................................................................7Cut the exposed ends of the cable to the length of the pins in the connector, as shown inthe following figure:36mm (1.4 in)8mm(0.32 in)8mm(0.32 in)8mm(0.32 in)22 mm (0.87 in)22 mm (0.87 in)BrownBlueGreen/yellowCrimping lugs (ferrules)Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-36 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................8Screw the wires into the terminal blocks to a torque of 0.4 Nm.Attention: Ensure that you connect the 0 V, -48 V, and Ground wires to the correctpins as shown in the following figure:...................................................................................................................................................................................................9Insert the connector assembly into the cover (with the correct ground position) and pullthe excess cable back out through the cable opening of the connector cover....................................................................................................................................................................................................10 Ensuring that the cable gasket is correctly seated, and tighten the nut to a torque of 1 Nm(0.737 lb-ft)....................................................................................................................................................................................................11 Attach the gasket, aligning the cutout in the gasket for the ground terminal over theground terminal on the connector. Insert the fixing screwCut conductorsto length4 mm (0.157 in)4 mm (0.157 in)4 mm (0.157 in)Pin 2:Brown, 0 V Pin 1:Blue, -48 VRegistration tab GroundTop view of connectorwith cover removedInstallation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-37DRAFTDRAFT
Attention: If the cutout in the gasket is not aligned with the ground terminal on theconnector, you will not be able to assemble the connector....................................................................................................................................................................................................12 Plug the DC power connector into the power connector on the bottom left of the 9764MCO module....................................................................................................................................................................................................13 Fix the DC power connector in position by tightening the screw on the DC powerconnector. Using a screwdriver with a Phillips head, torque to 0.4 Nm (0.295 lb ft).Connect DC power cordDANGERElectric-shock hazardSince the 9764 MCO operates on DC power, the risk of serious injury or death fromelectrocution exists throughout this procedure.Follow the first step of this procedure carefully and completely.WARNINGElectric-shock hazardThe current to the unit must be limited by an external fuse or circuit breaker incorporatedin the fixed wiring. The fuse or circuit breaker can be used as a disconnect device to turnoff the power to the system.Ensure that the system power is off and that power cables are safe to handle before youproceed with this procedure.WARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Use this procedure if you have a pre-assembled DC power cord.Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-38 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
...................................................................................................................................................................................................1Ensure that the power that feeds the DC power cable to the 9764 MCO is OFF, and blockaccess so that no one can restore power to that cable during this procedure....................................................................................................................................................................................................2Plug the DC power connector on the power cord into the power connector on the bottomleft of the 9764 MCO module....................................................................................................................................................................................................3Fix the DC power connector in position by tightening the screw on the DC powerconnector. Using a screwdriver with a Phillips head, torque to 0.4 Nm (0.295 lb ft).How to continueAfter connection of the power cable has been completed, continue with procedureProcedure 4-5: “Attach 9764 MCO module to 9764 Metro Dock” (p. 4-41).Installation of the 9764 MCO module9764 MCO cablingProcedure 4-4: Connect power cable........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-39DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
9764 MCO installationOverviewPurposeThis section provides the installation instructions for mounting the Alcatel-Lucent 9764Metro Cell Outdoor onto a 9764 Metro Dock.ContentsProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock 4-41Procedure 4-6: Orient 9764 MCO module 4-48Installation of the 9764 MCO module9764 MCO installationOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-40 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 4-5: Attach 9764 MCO module to 9764 Metro DockPurposeThis topic describes the procedures to attach the Alcatel-Lucent 9764 Metro Cell Outdoormodule to the 9764 Metro Dock.PrerequisitesA site survey has been conducted and a location for the device has been selected that isboth central to the public space and elevated to maximize coverage.Before installation begins, ensure that the following are in place:•Internet service is available for backhaul.•The 9764 Metro Dock has been installed and is in place.•The 9764 Metro Dock has been closed.•The power cable has been connected to the 9764 MCO module.•The key that was supplied with the 9764 Metro Dock is available.•The key extension tool is available.Before you beginRecord the 18 digit serial number before mounting the 9764 MCO module.Attention: Do not wear tinted glasses of any kind (for example, sunglasses or tintedsafety glasses) while performing this procedure, because they will reduce the clarityof your vision.Attach 9764 MCO module to 9764 Metro DockPerform the following steps to attach the 9764 MCO module to the 9764 Metro Dock:...................................................................................................................................................................................................1Remove the cover from the blind mate connector on the 9764 Metro Dock by unscrewingthe two M3x6 Torx screws that hold it in position....................................................................................................................................................................................................2Lubricate the sealing gasket on the blind mate connector by wiping a small quantity of asuitable lubricant, such as Silicone O-Ring grease or Vaseline, over the entire gasket. Thefollowing figure shows the sealing gasket:Installation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-41DRAFTDRAFT
...................................................................................................................................................................................................3Attach the 9764 MCO key to the key extension tool:1. Remove the M4 screw from the key extension tool.2. Position the key on the key extension tool and replace the screw so that the key issecurely clamped onto the extension tool....................................................................................................................................................................................................4To attach the 9764 MCO module to the 9764 Metro Dock, the 9764 Metro Dock metalslider must be in the “open” (“up”) position:1. Insert the key into the 9764 Metro Dock lock.2. Turn the key through an angle of approximately 90º to its hard stop position to unlockthe slider.3. Push the slider upwards and turn the key through an angle of approximately 60º to itshard stop position. The slider is now locked in the “open” (“up”) position.GasketView with keyand M4 screwKey Extension Tool(original variant)Key Extension Tool(new variant)Installation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-42 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................5Position the 9764 MCO module in front of the 9764 Metro Dock. Ensure the three metallugs on the 9764 MCO module are in front of the holes on the 9764 Metro Dock.60 - 70Key cam locked(not fully 60 ) keeping slider in open positionKey Extension ToolMetro Dock SliderUpper slot6mmOpen for MCO module attachOPENSlider in UP positionKey cannot be removedSlider upInstallation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-43DRAFTDRAFT
...................................................................................................................................................................................................6Push the 9764 MCO module into the 9764 Metro Dock.Important! Do not apply excessive or prolonged pressure when pushing the 9764MCO module into the 9764 Metro Dock, otherwise the slider will not spring back tothe “closed” (“down”) position....................................................................................................................................................................................................7To free the slider and then lock the 9764 MCO module onto the 9764 Metro Dock:1. Turn the key through an angle of approximately 60º to its hard stop position to freethe slider. The slider will automatically spring into the “down” position.Lug LugLugAlign lugs to holes onMetro DockPush MCO module ontoMetro DockInstallation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-44 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
0Key cam free (0 )Outline of9764 MCO moduleMCO assembled (not shown) and in free positionFREESlider springs into down positionIf the Slider does not automatically spring intothe down position, move the MCO slightlysideways or outwards to release the Slider.Additionally pulling down on the key extensiontool may also release the Slider.Slider up**Installation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-45DRAFTDRAFT
If slider does not automatically spring into the “down” position, move the 9764 MCOvery slightly sideways or outwards (away from the 9764 Metro Dock) to release theslider.2. Turn the key through an angle of approximately 90º to its hard stop position. Theslider is now locked in the “closed” (“down”) position and the key can be removedfrom the lock.Key cam (90 ) / Key removable90Outline of9764 MCO moduleMCO assembled (not shown) and LockedLOCKEDSlider in down position and LockedRemoveLower slotInstallation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-46 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................8Finally, remove the key from the key extension tool.How to continueAfter 9764 MCO module has been attached to the 9764 Metro Dock, continue withprocedure Procedure 4-6: “Orient 9764 MCO module ” (p. 4-48).LockingmechanismKey insertion toolnot presentInstallation of the 9764 MCO module9764 MCO installationProcedure 4-5: Attach 9764 MCO module to 9764 Metro Dock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-47DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 4-6: Orient 9764 MCO modulePurposeThis topic describes the procedures to orient the Alcatel-Lucent 9764 Metro Cell Outdoormodule towards its target using tilt and/or azimuth brackets.PrerequisitesEnsure that the following are in place:•The 9764 Metro Dock has been installed and is in place.•The 9764 MCO has been attached to the 9764 Metro Dock.•You have the equipment orientation plan.Orient 9764 MCO moduleWARNINGFall hazardFalls can occur when working at heights resulting in serious personal injury or death.To prevent a fall when working at heights (ladder, scaffold, manlift, roof etc.) follow safework practices and wear appropriate fall protection equipment.Perform the following steps to angle the 9764 MCO module towards its target:...................................................................................................................................................................................................1Refer to the equipment orientation plan.If... Then...If the 9764 Metro Dock is installed on either apole or a wall, and a tilt bracket has been used 1. Using the tilt angle positioning gauge,adjust the 9764 Metro Dock tilt (+- 20°up/down) to the desired angle.2. Using a ratchet wrench, tighten all the tiltpositioning gauge bolts and the bracketassembly hex bolts to fix the orientation ofthe 9764 Metro Dock.Installation of the 9764 MCO module9764 MCO installationProcedure 4-6: Orient 9764 MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-48 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
If... Then...If the 9764 Metro Dock is installed on a wall,and an azimuth bracket has been used 1. Using the azimuth angle positioninggauge, adjust the 9764 Metro Dockazimuth (+- 45° left/right) to the desiredorientation.2. Using a ratchet wrench, tighten all theazimuth positioning gauge bolts and thebracket assembly hex bolts to fix theorientation of the 9764 Metro Dock.If the 9764 Metro Dock is installed on a wall,and both the tilt bracket the azimuth brackethave been usedPerform both of the above procedures.How to continueAfter 9764 MCO module has been attached to the 9764 Metro Dock, continue withprocedure Procedure 4-7: “Post installation activities” (p. 4-51).Installation of the 9764 MCO module9764 MCO installationProcedure 4-6: Orient 9764 MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-49DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
9764 MCO post-installationOverviewPurposeThis section provides post-installation information and activities that should be carriedout after the Alcatel-Lucent 9764 Metro Cell Outdoor has been installed.ContentsProcedure 4-7: Post installation activities 4-51Procedure 4-8: Power on the 9764 MCO 4-52Installation of the 9764 MCO module9764 MCO post-installationOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-50 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure 4-7: Post installation activitiesFinal installation checksBefore leaving the installation site, check the following:...................................................................................................................................................................................................1Secure all cables along their routes....................................................................................................................................................................................................2Verify that all the exterior conduit and cable connections are secure....................................................................................................................................................................................................3Inspect the site for loose tools, materials, and parts. Remove all such loose tools,materials, and parts....................................................................................................................................................................................................4Continue with procedure Procedure 4-8: “Power on the 9764 MCO” (p. 4-52)Installation of the 9764 MCO module9764 MCO post-installationProcedure 4-7: Post installation activities........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction 4-51DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure 4-8: Power on the 9764 MCOPurposeThis topic describes how to power on the 9764 MCO.TroubleshootingIf any problems occur during power on, refer to the following document:•Alcatel-Lucent 9764 Metro Cell Outdoor LTE 2x1W and 2x2W Maintenance andTroubleshooting9YZ-04152-0057-REZZA (LR14.1.L)9YZ-05817-0057-REZZA (LR13.3.L)Power on the 9764 MCOPerform the following step to power on the 9764 MCO:...................................................................................................................................................................................................1Follow site-specific procedures to power on the 9764 MCO by applying power to thepower cable.After one to three seconds, the LED illuminates steady red, followed by approximately 15minutes of steady green, and then ceases to illuminate.If the LED does not follow this pattern of illumination, refer to Appendix A, “LED StateDescription” to troubleshoot the problem.Installation of the 9764 MCO module9764 MCO post-installationProcedure 4-8: Power on the 9764 MCO........................................................................................................................................................................................................................................................................................................................................................................................................................................................................4-52 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Appendix A: LED StateDescriptionOverviewPurposeThis chapter describes the LED status and descriptions for 9764 MCO LTE.ContentsLED status for 9764 MCO LTE A-2...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction A-1DRAFTDRAFT
LED status for 9764 MCO LTEOverviewThis topic describes the LED status on the9764 MCO LTE 2x1W and 9764 MCO LTE2x2W devices.Location of LEDThe following figure shows the location of the LED on the back of the 9764 MCO LTE2x1W and 9764 MCO LTE 2x2W:Hardware LED interpretation tableThe following table describes the possible states for the single bi-color LED:State Description LEDPower off Power off OFFInitial state Power on or Restart ON (Red)Software downloading duringsystem initializationSoftware downloading Blinking(Green)Failure 9764 MCO LTE start-up or operational failure ON (Red)9764 MCO LTE becomesoperational9764 MCO LTE becoming operational ON (Green)(Note: LED isswitched OFFafter 15 minutesof stableoperation)9764 MCO LTE is operational 9764 MCO LTE has been in stable operation for 15 minutes OFFFigure A-1 Location of LEDLEDLED State Description LED status for 9764 MCO LTE........................................................................................................................................................................................................................................................................................................................................................................................................................................................................A-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Appendix B: Installation of the9764 MCO Wi-Fi APOverviewPurposeThis appendix provides instructions for attaching the Alcatel-Lucent 9764 Metro CellOutdoor Wi-Fi AP to the 9764 MCO module.The 9764 MCO Wi-Fi AP is optional. If you do not have a 9764 MCO Wi-Fi AP, then donot perform the procedures in this appendix.ContentsPhysical description B-29764 MCO Wi-Fi AP pre-installation information B-8Procedure B-1: Remove 9764 MCO module from 9764 Metro Dock B-9Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764 MCO module B-19LED state description - 9764 MCO Wi-Fi AP B-25...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-1DRAFTDRAFT
Physical descriptionProduct overviewThe 9764 Metro Cell Outdoor Wi-Fi AP is housed in a weatherized enclosure containingthe following active components:•Integrated antennas supporting 2x2 MIMO.This figure reflects the location of the 9764 MCO Wi-Fi AP module when attached to thetechnology-specific module (9764 MCO WCDMA module or 9764 MCO LTE module)of the Alcatel-Lucent 9764 Metro Cell Outdoor.Figure B-1 9764 MCO Wi-Fi AP attached to 9764 MCO hardware variantsInstallation of the 9764 MCO Wi-Fi AP Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
This figure reflects the available 9764 MCO Wi-Fi AP module models (9764 Metro CellOutdoor Wi-Fi AP V1.0 HG [high gain] and 9764 Metro Cell Outdoor Wi-Fi AP V1.0MG [medium gain]).This figure reflects the major components of both the High-gain and Medium-gainmodels of the 9764 MCO Wi-Fi AP.Figure B-2 9764 MCO Wi-Fi AP - closed housingFigure B-3 9764 MCO Wi-Fi AP - cutaway viewInstallation of the 9764 MCO Wi-Fi AP Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-3DRAFTDRAFT
The physical dimensions of the 9764 MCO Wi-Fi AP module are:Table B-1 9764 MCO Wi-Fi AP physical characteristicsPhysical property 9764 MCO Wi-Fi AP V1.0MG model9764 MCO Wi-Fi AP V1.0HG modelDimension (Height x Widthx Depth)5cm x 13cm x 7cm 9cm x 13cm x 7cmVolume 0.5 liters 0.8 litersWeight 0.35 kg 0.4 kgProduct base items and configurationsThe 9764 MCO Wi-Fi AP module is a single, field-replaceable, unit that may be mountedto many Alcatel-Lucent 9764 Metro Cell Outdoor variants.Available models include:•9764 Metro Cell Outdoor Wi-Fi AP V1.0 HG (contains High-gain integratedantennas)•9764 Metro Cell Outdoor Wi-Fi AP V1.0 MG (contains Medium-gain integratedantennas)The unit is shipped with 3 M3 10mm Torx screws (part number 1AD013170007) used tosecure the 9764 MCO Wi-Fi AP module to the 9764 MCO module.Connection interfacesThe 9764 MCO Wi-Fi AP module has a single interface connector that plugs into the backbottom of the technology-specific module (9764 MCO WCDMA module or 9764 MCOLTE module) of the Alcatel-Lucent 9764 Metro Cell Outdoor, carrying both power and allcommunication between the two components.Installation of the 9764 MCO Wi-Fi AP Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
This figure reflects the connection point on the back bottom of the technology-specificmodule (Alcatel-Lucent 9764 Metro Cell Outdoor WCDMA or Alcatel-Lucent 9764Metro Cell Outdoor LTE) of the Alcatel-Lucent 9764 Metro Cell Outdoor.This figure provides a cutaway side view of the 9764 MCO Wi-Fi AP module whenconnected to the technology-specific module (9764 MCO WCDMA module or 9764MCO LTE module) of the Alcatel-Lucent 9764 Metro Cell Outdoor.Figure B-4 9764 MCO Wi-Fi AP connection point on 9764 MCOFigure B-5 9764 MCO Wi-Fi AP connected to 9764 MCO (cutaway side view)Installation of the 9764 MCO Wi-Fi AP Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-5DRAFTDRAFT
AntennasThe 9764 MCO Wi-Fi AP supports 2 integrated antennas optimized for 2x2 MIMO withup to 2 spatial streams.Two hardware models are available:•9764 MCO Wi-Fi AP V1.0 MG model with Medium-gain integrated antennas.•9764 MCO Wi-Fi AP V1.0 HG model with High-gain integrated antennas.Status indicatorsThere is an external single bi-color LED (amber/green) on the upper side of the 9764MCO Wi-Fi AP module housing (pointing up towards the 9764 MCO LTE/WCDMAmodule radome).Although external, this LED is not easily visible and is not used for post-installationtroubleshooting. During initial cell power-up, however, the installation technician mayobserve the LED changes as the unit goes through its booting sequences. Once the cell isin normal operation for 30 minutes, the LED will turn off automatically.Refer to “LED state description - 9764 MCO Wi-Fi AP” (p. B-25) for details.The 9764 MCO Wi-Fi AP is monitored/managed remotely at the Alcatel-Lucent 9772Wi-Fi Service Controller.Product labelingTo the top of the 9764 MCO Wi-Fi AP module will be affixed three labels:1. A product label reflecting:•Vendor name/Icon•Customer ID•Model name•Part number•Lock / Unlock mode iconNote: The “Unlock” icon applies only to units designated as R&D lab mode.•Serial number•MAC address•CLEI code (U.S. only)•Data matrix barcode (2D MicroPDF Symbol) for Part number, Serial number,MAC address, and CLEI code (CLEI code is for U.S. only)2. A regulatory label reflecting:•Vendor name/Icon•Product nameInstallation of the 9764 MCO Wi-Fi AP Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
•Regulatory rules•Power input•Enclosure rating•Applicable regulatory and environmental certification logos (for example, CE andWEEE recycling logos)•Manufacturer name3. (NAR only) An FCC label reflecting:•Vendor name/Icon•FCC IDInstallation of the 9764 MCO Wi-Fi AP Physical description........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-7DRAFTDRAFT
9764 MCO Wi-Fi AP pre-installation informationIntroductionImportant! The 9764 Metro Cell Outdoor Wi-Fi AP cannot be attached to the 9764MCO module when the 9764 MCO module is attached to the 9764 Metro Dock.If the 9764 MCO module is already attached to the 9764 Metro Dock, then the 9764MCO module must first be removed from the 9764 Metro Dock. Refer to ProcedureB-1: “Remove 9764 MCO module from 9764 Metro Dock” (p. B-9).When installing a 9764 MCO module for the first time, if a 9764 MCO Wi-Fi AP isalso to be installed, then attach the 9764 MCO Wi-Fi AP module to the 9764 MCOmodule before attaching the 9764 MCO module to the 9764 Metro Dock.Product delivery contentsThe following items are supplied with the 9764 MCO Wi-Fi AP:•The 9764 MCO Wi-Fi AP module•Three M3 10mm Torx screws (to secure the 9764 MCO Wi-Fi AP module to the 9764MCO module).Variable parts and ancillary itemsIn addition to the standard delivered parts, the following variable and ancillary items areavailable:•There are no ancillary parts for the 9764 MCO Wi-Fi AP.Installation tools requiredThe following tools may be used during installation:•Snips•Screwdrivers (power and/or manual):– Phillips (flat blade)– Torx (T10)•9764 Metro Dock keyInstallation of the 9764 MCO Wi-Fi AP 9764 MCO Wi-Fi AP pre-installation information........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Procedure B-1: Remove 9764 MCO module from 9764 MetroDockPurposeThis topic describes the procedure to remove the 9764 MCO module from the 9764 MetroDock if the 9764 MCO module has already been attached to the 9764 Metro Dock.PrerequisitesBefore installation begins, ensure the following are available:•The key that was supplied with the 9764 Metro Dock•Snips (to cut cable tie)•Phillips-head screwdriver (to loosen power cable screw)DANGERElectric-shock hazardRisk of personal injury or death, property damage, and/or equipment damage.Refer to the Safety chapter for all Dangers, Warnings, Cautions and Notices.NOTICEService-disruption hazardFollowing the procedure below will result in service disruption.Notify the OMC administrator of a service outage before commencing.Before you beginPerform this procedure only if the 9764 MCO module has been installed on the 9764Metro Dock.Remove the 9764 MCO module...................................................................................................................................................................................................1Shut off the power that feeds the power cable to the 9764 MCO....................................................................................................................................................................................................2Block access so that no one can restore power to that cable during the course of thisreplacement procedure.Installation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-9DRAFTDRAFT
Attention: Blocking access likely consists of not only putting a physical impedimentin the way, but also broadly circulating or broadcasting a warning about the hazardand getting the cooperation of persons who have the authority to limit the access ofothers....................................................................................................................................................................................................3If a cable tie will inhibit separating the 9764 MCO module from the 9764 Metro Dock,snip the cable tie....................................................................................................................................................................................................4Perform this step only if:•you are replacing the 9764 MCO module, or•if there is an external GPS antenna connection and the GPS cable is too short,prohibiting you from easily removing the MCO.The 9764 MCO module could be deployed using either an external GPS antenna or theinternal GPS antenna. Follow the appropriate procedure below for type of 9764 MCOmodule deployed and the GPS antenna configuration used, and note which type of GPSantenna was used for reference when reattaching the 9764 MCO module.If... Then... Viewdeployed with anexternal GPS antenna onthe 2x1W MCOdisconnect the GPS adaptercable by pulling it off of theQMA-type connector. TheGPS antenna QMA connectionis located on the upperbackside of the 9764 MCOmodule.Tip: Unplugging the GPSQMA connector needs verylittle force. If the accessmakes it difficult to unplug,use a non-metallic screwdriver as a lever to gentlyrelease the connector.deployed using theinternal GPS antenna onthe 2x1W MCOthe GPS bridge cable, attachedto the QMA-type connectorslocated on the top part of theheatsink side of the 9764MCO module, can remain inplaceGPS bridge cableInstallation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
If... Then... Viewdeployed with anexternal GPS antenna onthe 2x2W MCOdisconnect the GPS adaptercable by pulling it off of theQMA-type connector. TheGPS antenna QMA connectionis located half way down theheat sink on the right handside of the 9764 MCOmodule.Tip: Unplugging the GPSQMA connector needs verylittle force. If the accessmakes it difficult to unplug,use a non-metallic screwdriver as a lever to gentlyrelease the connector.QMA - Quick SMAGPS antenna switchdeployed using theinternal GPS antenna onthe 2x2W MCOno action is needed....................................................................................................................................................................................................5Perform this step for the 9764 MCO LTE 2x2W MCOs only and only if:•you are replacing the 9764 MCO module, or•there is an attached RF antenna and the RF antenna cable is too short, prohibiting youfrom easily removing the MCO.For the 9764 MCO LTE 2x2W MCOs only: Disconnect the external RF antennas bypulling them off of the QN connectors located at the top of the heat sink side of the 9764MCO module.Installation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-11DRAFTDRAFT
...................................................................................................................................................................................................6Disconnect the ground cable.The LTE 9764 MCO module utilizes a short ground cable to the 9764 Metro Dock. Fromthe underside of the 9764 MCO module unclip and disconnect the ground cable connectorfrom the ground cable connection tab on the 9764 MCO module.QN - Quick NRX/TX antennaInstallation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-12 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................7If the 9764 MCO configuration requires use of the key extension to reach the lock, thenattach the key to the key extension.1. Remove the M4 screw from the key extension.2. Insert the key.3. Replace the screw so that the tool clamps firmly onto the key.Figure B-6 9764 Metro Dock to LTE 9764 MCO module grounding cableFaston tab (M5)connector onMCO ModuleGround cableconnection onMCO ModuleGround cableconnection onMetro DockFigure B-7 Key extensionView with keyand M4 screwKey Extension Tool(original variant)Key Extension Tool(new variant)Installation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-13DRAFTDRAFT
...................................................................................................................................................................................................8To remove the 9764 MCO module from the 9764 Metro Dock, the 9764 Metro Dockmetal slider must be in the “open” (“up”) position:1. Insert the key into the 9764 Metro Dock lock.2. Turn the key through an angle of approximately 90° to its hard stop position to unlockthe slider.Note: Keep a grip on the key extension tool, because with the slider in the “down”position, the key can slip out of the lock and fall to the ground.3. Push the extension tool upwards to move the slider up and turn the key through anangle of approximately 60° to its hard stop position. The slider is now locked in the“open” (“up”) position.Installation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-14 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
The key and extension may remain in the lock while completing the subsequent hardwarereplacement steps....................................................................................................................................................................................................9Pull the 9764 MCO module straight out of and clear from the 9764 Metro Dock.60 - 70Key cam locked(not fully 60 ) keeping slider in open positionKey Extension ToolMetro Dock SliderUpper slot6mmOpen for MCO module attachOPENSlider in UP positionKey cannot be removedSlider upInstallation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-15DRAFTDRAFT
...................................................................................................................................................................................................10 On the bottom left of the 9764 MCO module, loosen the screw that locks the power lineconnector into its mating connector in the 9764 MCO module.Figure B-8 Pull 9764 MCO module from Metro DockPull MCO module out ofMetro DockFigure B-9 AC power line connectorSide view of connectorTop view of connectorwith cover removedRegistration tabTerminals}Nut30 mm screwwith gasketCoverInstallation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-16 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................11 Pull the power cable plug straight out of its mating connector in the 9764 MCO module....................................................................................................................................................................................................12 Important! If a Wi-Fi AP is attached to the 9764 MCO module, perform this step aswell as the following two steps only if the 9764 MCO module is being replaced;otherwise skip to Step 14. If a Wi-Fi AP is not attached to the 9764 MCO module,skip to Step 14.Using a T10 Torx screwdriver, loosen the three M3 10mm Torx screws from theattachment plate on the back of the 9764 MCO module and 9764 MCO Wi-Fi AP module.Figure B-10 DC power line connectorNut32 mm screwwith gasketTop view of connectorTop view of connectorwith cover removedTerminals}Figure B-11 9764 MCO Wi-Fi AP module attached to 9764 MCO moduleInstallation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-17DRAFTDRAFT
...................................................................................................................................................................................................13 Set the screws and the attachment plate aside (retain for later use)....................................................................................................................................................................................................14 Pull the 9764 MCO Wi-Fi AP module off of the 9764 MCO module and set the 9764MCO Wi-Fi AP module aside....................................................................................................................................................................................................15 Rest the 9764 MCO module gently against a secure, supportive, flat surface and block itfrom falling.How to continueContinue to Procedure B-2: “Attach 9764 MCO Wi-Fi AP module to 9764 MCO module”(p. B-19).Installation of the 9764 MCO Wi-Fi AP Procedure B-1: Remove 9764 MCO module from 9764 MetroDock........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-18 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764 MCOmodulePurposeThis topic describes the procedures to attach the 9764 MCO Wi-Fi AP module to the 9764MCO module.PrerequisitesBefore installation begins, ensure the following:•T10 Torx screwdriver (power and/or manual) is available.•Internet service is available.•The 9764 MCO module is not attached to the 9764 Metro Dock.If removal is necessary, refer to procedure Procedure B-1: “Remove 9764 MCOmodule from 9764 Metro Dock” (p. B-9).Installation of the 9764 MCO Wi-Fi AP Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-19DRAFTDRAFT
Attach 9764 MCO Wi-Fi AP module to 9764 MCO moduleNOTICEESD hazardSemiconductor devices can be damaged by electrostatic discharges (ESD)The following rules must be complied with when handling any module containingsemiconductor components:•Wear conductive or antistatic working clothes (for example, coat made of 100%cotton).•Wear a grounded wrist strap.•Wear shoes with conductive soles on a conductive floor surface or conductive workmat.•Leave the modules in their original packaging until ready for use.•Make sure there is no difference in potential between yourself, the workplace, and thepackaging before removing, unpacking, or packing a module.•Whenever handling ESD-sensitive components, do not touch any connection pins ortracks.•Place modules removed from the equipment on a conductive surface.•Test or handle the module only with grounded tools on grounded equipment.•Handle defective modules exactly like new ones to avoid causing further damage.Perform the following steps to attach the 9764 MCO Wi-Fi AP module to the 9764 MCOmodule:...................................................................................................................................................................................................1Remove the 9764 MCO Wi-Fi AP module from its packaging....................................................................................................................................................................................................2Using a T10 Torx screwdriver, remove the cover over the Wi-Fi AP connector on thelower back of the 9764 MCO module by unscrewing the three screws.The following figure shows the Wi-Fi AP connector cover:Installation of the 9764 MCO Wi-Fi AP Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-20 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Important! Ensure that the appropriate gasket surrounding the connector is in placeon the 9764 MCO module (as shown in Figure B-13, “Wi-Fi AP connector on 9764MCO module” (p. B-21)).Note: Retain the cover and the three (3) cover screws. Should the need arise toremove but not replace the 9764 MCO Wi-Fi AP module in the future, the dummycover and its screws must be reattached to the 9764 MCO module....................................................................................................................................................................................................3Push the 9764 MCO Wi-Fi AP module onto the Wi-Fi AP connector.Figure B-12 Wi-Fi AP connector cover on 9764 MCO moduleCover over 9764 MCO Wi-Fi AP connectorFigure B-13 Wi-Fi AP connector on 9764 MCO moduleInstallation of the 9764 MCO Wi-Fi AP Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-21DRAFTDRAFT
...................................................................................................................................................................................................4Using a T10 Torx screwdriver and the three M3 10mm Torx screws shipped with the 9764MCO Wi-Fi AP module, screw the attachment plate to the 9764 MCO module and to theback of the 9764 MCO Wi-Fi AP module, and tighten all screws.Torque screws to 0.6 Nm (0.443 lb ft).The following figure shows the 9764 MCO Wi-Fi AP module attached to the 9764 MCOmodule:How to continueAttach the 9764 MCO module to the 9764 Metro Dock module by following theprocedures in Chapter 4, “Installation of the 9764 MCO module”.9764 MCO Wi-Fi AP integration overviewIntegration refers to the entire process from hardware installation to “normal operation”.9764 MCO Wi-Fi AP integration proceeds as follows:1. Hardware is installed.The 9764 MCO Wi-Fi AP module is physically installed on the 9764 MCO module,and the 9764 MCO module is physically installed on the 9764 Metro Dock moduleand all cabling completed.2. Power is applied to the 9764 MCO (and by default, to the 9764 MCO Wi-Fi APmodule).Figure B-14 9764 MCO Wi-Fi AP module attached to 9764 MCO moduleInstallation of the 9764 MCO Wi-Fi AP Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-22 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFTEND OF STEPS...................................................................................................................................................................................................
3. The switch on the 9764 MCO module contains a default configuration that connectsthe 9764 MCO Wi-Fi AP port to the backhaul port (there are no 9764 MCO Wi-Fi APOAM parameters to be configured prior to initial power-up).The switch will forward Wi-Fi packages as soon as the 9764 MCO module softwarehas booted and as soon as the 9764 MCO Wi-Fi AP software is running.4. A connection between 9764 MCO Wi-Fi AP and Alcatel-Lucent 9772 Wi-Fi ServiceController (9772 Wi-Fi SC) is automatically established.5. The 9764 MCO Wi-Fi AP downloads the latest software version from the appropriatefile server (if applicable).6. The 9764 MCO Wi-Fi AP is provisioned and configured via the 9772 Wi-Fi SC.A 30-minute timer is started after the configuration is sent successfully from the 9772Wi-Fi SC. During this 30 minutes, the LED on top of the 9764 MCO Wi-Fi APmodule illuminates and is visible through the narrow gap between the bottom of the9764 MCO module and the top of the 9764 MCO Wi-Fi AP module.For information on the 9772 Wi-Fi SC, refer to the documents listed in the followingtable:Refer to this document At this location For more information onAlcatel-Lucent 9772 Wi-FiService Controller V1.0 LHardware Installation,3MN-01840-0001- RJZZA(http://support.alcatel-lucent.com)Instructions for installing the9772 WiSC-L hardware andaccessing its managementinterfaces.Alcatel-Lucent 9764 and9772 Metro Cell OutdoorWi-Fi AP and Wi-Fi ServiceController, Release WA5.5,System Reference Guide,3MN-01840-0002-RKZZA(http://support.alcatel-lucent.com)Instructions for accessingand using the web-basedgraphic user interface (GUI)to manage/administer the9772 Wi-Fi ServiceController and 9764 MCOWi-Fi Access PointAlcatel-Lucent 9764 and9772, Metro Cell OutdoorWi-Fi AP and Wi-Fi ServiceController, Release WA 5.5,CLI Reference Guide,3MN-01840-0003-RKZZA(http://support.alcatel-lucent.com)Instructions for accessingand using command lineinterface (CLI) tomanage/administer the 9772Wi-Fi Service Controllerand 9764 MCO Wi-FiAccess Point.7. The field technician may choose to observe the LED colors and blinking patterns toensure error-free boot-up and normal operation. Refer to “LED state description -9764 MCO Wi-Fi AP” (p. B-25) for details.Installation of the 9764 MCO Wi-Fi AP Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-23DRAFTDRAFT
- If normal operation is achieved, then the LED is automatically turned off when the30-minute timer expires.- If there are problems, then the LED displays the applicable error color/pattern. Referto “LED state description - 9764 MCO Wi-Fi AP” (p. B-25) for details.8. The field technician will make the first test call – provided all necessary core networkelements (NEs) are configured properly (for example, WLAN GW, AAA, etc.).Installation of the 9764 MCO Wi-Fi AP Procedure B-2: Attach 9764 MCO Wi-Fi AP module to 9764MCO module........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-24 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
LED state description - 9764 MCO Wi-Fi APOverviewThe 9764 MCO Wi-Fi AP module has a single external bi-color LED (red/green) on thetop of the module housing.The LED illuminates with different colors and blinking patterns during boot-up, then isautomatically turned off after normal operation has been achieved and the 30-minutetimer expires. If there are problems, then the LED displays the applicable errorcolor/pattern.Due to limited visibility requiring direct line-of-site between the 9764 MCO Wi-Fi APmodule and the 9764 MCO module, the LED is not intended for ongoing troubleshootingafter the unit has been successfully deployed. However, the field technicianinstalling/replacing the 9764 MCO Wi-Fi AP module may watch the LED during boot-upif desired.LED statuses during boot-upTip: In the following table, note that “Slow blinking” refers to an LED blink cycle of2500 ms on, 2500 ms off; “Fast blinking” refers to an LED blink cycle of 500 ms on,500 ms off.After the 9764 MCO Wi-Fi AP hardware has been installed, upon power-up the LEDreflects 9764 MCO Wi-Fi AP statuses as follows:Table B-2 9764 MCO Wi-Fi AP LEDs during boot-upInstallation /commissioningstep9764 MCOWi-Fi AP StateRed LEDsegmentGreen LEDsegmentCombined LEDbehavior1. Power-up withautotestBOOTING Solid On Solid On Solid On (appearsorange)2. 9764 MCO Wi-FiAP tries to getadopted by the 9772Wi-Fi ServiceControllerADOPTING Slow blinking Off Slow red blinking3. (optional) 9772Wi-Fi ServiceController pushes asoftware upgradeUPGRADING Off Slow blinking Slow green blinkingInstallation of the 9764 MCO Wi-Fi AP LED state description - 9764 MCO Wi-Fi AP........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-25DRAFTDRAFT
Table B-2 9764 MCO Wi-Fi AP LEDs during boot-up (continued)Installation /commissioningstep9764 MCOWi-Fi AP StateRed LEDsegmentGreen LEDsegmentCombined LEDbehavior4. WLANs aremapped to radios,normal serviceOPERATIONAL Service on 5GHz: SlowblinkingService on 2.4GHz: SlowblinkingWith both radiosoperating: slow orangeblinking5. After 30 minutesin the same state(Note: the LEDtimeout defaultsetting is 30minutes, but isconfigurable by theAdministrator toany value from 15to 1440 minutes.)HIDING Off Off OffLED functionality during OPERATIONAL statesThe 2 9764 MCO Wi-Fi AP radios are mapped to a color segment of the LED:•Radio 1 (2.4 GHz) maps to the GREEN segment.•Radio 2 (5 GHz) maps to the RED segment.There are 2 factors that affect the LED segment that is associated with each radio:•If the radio is disabled (shutdown) or not by the administrator (this factor takesprecedence).•If a WLAN is mapped to the radio, making the radio usable.If a radio has at least a WLAN mapped to it and it is enabled, then it is operational(meaning, it will beacon and provide client service).Tip: In the following tables, note that “Slow blinking” refers to an LED blink cycle of2500 ms on, 2500 ms off; “Fast blinking” refers to an LED blink cycle of 500 ms on,500 ms off. An asterisk (*) means that the setting does not matter.Table B-3 9764 MCO Wi-Fi AP LEDs based on Admin status and WLAN mappingRadio's Admin status Radio's WLAN mapping LED segmentDisabled * OffEnabled no WLAN mapped Fast blinkingEnabled WLAN mapped Slow blinkingInstallation of the 9764 MCO Wi-Fi AP LED state description - 9764 MCO Wi-Fi AP........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-26 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Table B-4 9764 MCO Wi-Fi AP LEDs during normal operation statesRADIO 1 / 2.4 GHz / GREEN LEDSegmentRADIO2/5GHz/REDLEDSegment COMBINEDLEDBehaviorAdminstatusWLANmappingSegmentBehaviorAdminstatusWLANmappingSegmentBehaviorDisabled * Off Disabled * Off OffEnabled no WLAN Fast Disabled * Off Fast GreenWLAN Slow Slow GreenDisabled * Off Enabled no WLAN Fast Fast Red* WLAN Slow Slow RedEnabled no WLAN Fast Enabled no WLAN Fast Fast OrangeWLAN Slow WLAN Slow Slow OrangeWLAN Slow no WLAN Fast Fast Red +Slow Green(results in agreen/orange/red pattern)no WLAN Fast WLAN Slow Slow Red +Fast Green(results in agreen/orange/red pattern)Installation of the 9764 MCO Wi-Fi AP LED state description - 9764 MCO Wi-Fi AP........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction B-27DRAFTDRAFT
Installation of the 9764 MCO Wi-Fi AP LED state description - 9764 MCO Wi-Fi AP........................................................................................................................................................................................................................................................................................................................................................................................................................................................................B-28 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Appendix C: Productconformance statementsOverviewPurposeThis section presents the product conformance statements that apply to the 9764 MCOAccess Point equipment.The statements that are required are determined primarily by national or multinationalregulations. However, in some regions, contract terms determine which statements arerequired.The presence of the statement indicates that the product does comply with that statementwherever it is required to do so.ContentsUnited States compliance C-2Federal Communications Commission C-3Product safety and RF exposure C-4FDA/IEC optical transmitter product compliance statements C-5Eco-environmental statements C-6European Union C-7CE marking C-8EMC and radio spectrum compliance C-9Product safety and RF exposure C-10Eco-environmental statements C-13...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-1DRAFTDRAFT
United States complianceIntroductionPurposeThe statements that follow are the product conformance statements that apply to the 9764MCO when deployed in the United States.ContentsFederal Communications Commission C-3Product safety and RF exposure C-4FDA/IEC optical transmitter product compliance statements C-5Eco-environmental statements C-6Product conformance statementsUnited States complianceIntroduction........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Federal Communications CommissionFederal Communications CommissionImportant! Changes or modifications not expressly approved by Alcatel-Lucent, Inc.could void the user’s authority to operate the equipment.This device complies with Part 15 of the 47 CFR FCC Rules. Operation is subject to thefollowing two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that maycause undesired operation.47 CFR FCC Part 15 Class BNote: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the 47 CFR FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna•Increase the separation between the equipment and receiver•Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected•Consult the dealer or an experienced radio/TV technician for help.RF approvalThis equipment complies with Part 2, Subpart J - Equipment Authorization Procedures, ofthe 47 CFR FCC Rules.This device complies with Part 22 – Public Mobile Services, Subpart H – CellularRadiotelephone Services.This equipment complies with Part 24 - Personal Communications Services, Subpart E -Broadband PCS.Product conformance statementsUnited States complianceFederal Communications Commission........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-3DRAFTDRAFT
Product safety and RF exposureProduct safetyThe equipment complies with the following product safety specifications:Standard reference TitleSafety EN 60950-22 (including EN 60950-1)RF exposureNorth America:•Canada Safety Code 6 – Limits of Human Exposure to Radio frequencyElectromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz. Togetherwith Canada RSS 102 for compliance of radio communication apparatus.•USA FCC 47CFR 1.1310 – Radio frequency radiation exposure limits. Together withFCC OET Bulletin 65 and its supplements for evaluating compliance with FCCguidelines for human exposure to RF fields.Note: The results of the RF exposure assessment for NAR regulations and derivedrecommendations may be extended to other countries using similar regulations.The 9764 MCO is basically a radio transmitter and receiver. When it is turned on, itreceives and transmits radio frequency (RF) signals.The system controls the transmitted power level within a range up to 1W per antenna portfor the following models:•9764 MCO V1.0 B25 LTE 2x1W•9764 MCO V1.1 B2 LTE 2x1W•9764 MCO V1.1 B2/B25 LTE 2x1Wand up to 2W per antenna port for the 9764 MCO V1.1 B2 LTE 2x2W model.Installation of 9764 MCO shall be performed in accordance with all applicablemanufacturer's recommendations, and national laws and regulations. In particular:•Workers that are required to work in close proximity to the equipment, for examplemaintenance personnel, should strictly follow instructions provided by their employer.•Workers equipped with personal medical electronic devices, such as pacemakers andhearing aids, shall consult the manufacturer's instructions and consult theiroccupational health practitioner.The 9764 MCO shall be installed and operated with a minimum separation distance of20 cm (8 inches) between the radiator and user (see: USA – FCC OET Bulletin 65 andsupplements and Canada – RSS 102).Product conformance statementsUnited States complianceProduct safety and RF exposure........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
FDA/IEC optical transmitter product compliance statementsFDA/IEC optical transmitter product complianceAlcatel-Lucent declares that this equipment complies with the Food and DrugAdministration’s Center for Devices and Radiological Health (FDA/CDRH) regulations21 CFR 1040.10 and 1040.11. It is a Class I/1 laser optical fiber communication systems“product” under the FDA.This Product is designed to ensure that personnel operating the product are notendangered by laser radiation during normal operation and fault conditions. This productdoes not present a risk of eye injury because it is fully enclosed and does not containembedded lasers greater than Class I/1 unless otherwise noted.Laser warningWARNINGUse of controls or adjustments or performance of procedures other than those specifiedherein may result in hazardous laser radiation exposure.Do not view directly into the laser beam with optical instruments such as a fibermicroscope because viewing of laser emission in excess of Class 1 limits significantlyincreases the riskof eye damage.Never lookinto the end of an exposed fiber or an open connector as long as the opticalsource is switched on.Ensure that the optical source is switched off before disconnecting optical fiberconnectors.Laser hazardProduct conformance statementsUnited States complianceFDA/IEC optical transmitter product compliance statements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-5DRAFTDRAFT
Eco-environmental statementsPackaging collection and recovery requirementsCountries, states, localities, or other jurisdictions may require that systems be establishedfor the return and/or collection of packaging waste from the consumer, or other end user,or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for thereturn and/or collection of the packaging waste may be established.For more information regarding collection and recovery of packaging and packagingwaste within specific jurisdictions, contact the Alcatel-Lucent Environment, Health andSafety organization or Alcatel-Lucent Hazardous Waste Center technical support at (888)539-2783.Material content complianceThe following notification applies to Alcatel-Lucent products distributed for sale, resale,or use.This product, part, or both may include a lithium-manganese dioxide battery, whichcontains very small amounts of a perchlorate substance. Special handling may apply.For California:Perchlorate Material - special handling may apply.See (https://dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm).Product conformance statementsUnited States complianceEco-environmental statements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
European UnionIntroductionPurposeThe statements that follow are the product conformance statements that apply to theAlcatel-Lucent 9764 B7 MCO LTE equipment when deployed in the European Union.Declaration of Conformity for radio and telecommunication terminal equipmentunder the scope of Directive 1999/5/EC.Hereby, Alcatel-Lucent declares that the equipment documented in this publication is incompliance with the essential requirements and other relevant provisions of Directive1999/5/EC.The technical documentation as required by the Conformity Assessment procedure is keptat the Alcatel-Lucent location which is responsible for this product. For more informationplease contact your local Alcatel-Lucent Customer Service Organization.ContentsCE marking C-8EMC and radio spectrum compliance C-9Product safety and RF exposure C-10Eco-environmental statements C-13Product conformance statementsEuropean UnionOverview........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-7DRAFTDRAFT
CE markingCE markingThis product has been CE-marked in accordance with the following European Directives:•1999/05/EC Radio and Telecommunication Terminal Equipment (R&TTE)Product conformance statementsEuropean UnionCE marking........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
EMC and radio spectrum complianceEMC complianceThe equipment complies with the following EMC specifications:Standard reference TitleEN 301 489-1 V1.9.2 Electromagnetic compatibility and Radiospectrum Matters (ERM); ElectroMagneticCompatibility (EMC) standard for radioequipment and services; Part 1: Commontechnical requirementsEN 301 489-23 V1.5.1 Electromagnetic compatibility and Radiospectrum Matters (ERM); ElectroMagneticCompatibility (EMC) standard for radioequipment and services; Part 23: Specificconditions for IMT-2000 CDMA, Direct Spread(UTRA and E-UTRA) Base Station (BS) radio,repeater and ancillary equipmentEN 55022:2006/A1:2007 Class B Limits and methods of measurement of radiodisturbance characteristics of informationtechnology equipmentEN 55024:1998/A1:2001/A2:2003 Information technology equipment. Immunitycharacteristics. Limits and methods ofmeasurement and measuring.Radio spectrum complianceThe equipment complies with the following radio spectrum specifications:Standard reference TitleEN 301 908-1 V5.2.1 IMT cellular networks; Harmonized ENcovering the essential requirements of article3.2 of the R Directive; Part 1: Introduction andcommon requirementsEN 301 908-3 V5.2.1 IMT cellular networks; Harmonized ENcovering the essential requirements of article3.2 of the R Directive; Part 3: CDMA DirectSpread (UTRA FDD) Base Stations (BS)Product conformance statementsEuropean UnionEMC and radio spectrum compliance........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-9DRAFTDRAFT
Product safety and RF exposureProduct safetyThe equipment complies with the following product safety specifications:Standard reference TitleEN 60950-1: Ed 2 of 2006 + A1 (2010) +A11 (2009) + A12 (2011)Information Technology Equipment – Safety –Part 1: General RequirementsEN 60950-22 (Ed 1 of 2006) + A11 (2008) Information Technology Equipment – Safety –Part 22: Equipment to be installed outdoorsRF exposureEurope:•European Council recommendation 1999/519/EC on the limitation of exposure of thegeneral public to electromagnetic fields (0 Hz to 300 GHz). Together with EN 50383,EN 50384, EN 50385 and IEC 62232.•Directive 2013/35/EU of the European Parliament and of the Council on the minimumhealth and safety requirements regarding the exposure of workers to the risks arisingfrom physical agents (electromagnetic fields). Together with IEC 62232.Note: These standards are aligned with the Guidelines of 1998 from the InternationalCommission for Non-Ionizing Radiation Protection (ICNIRP). The recommendationsprovided below may also be extended to other ICNIRP based regulations.The Alcatel-Lucent 9764 MCO V1.1 LTE 2x1W B3/B7 is basically a radio transmitterand receiver. When it is turned on, it receives and transmits radio frequency (RF) signals.The system controls the transmitted power level within a range up to 1 W per antennaconnector.The Specific Absorption Rate (SAR) is a value that corresponds to the relative amount ofRF energy absorbed in the body of a person standing in the close vicinity of theequipment. Measured SAR values result from an extensive assessment process defined byinternational standards. Tests are performed in strict laboratory settings at the highesttransmitted power of the equipment. When in operation, the SAR resulting from of theequipment emissions will most likely be substantially less than the measured valuesbecause of a variety of factors including number and proximity of connected end users,telecom traffic etc..Product conformance statementsEuropean UnionProduct safety and RF exposure........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Installation for the Alcatel-Lucent 9764 MCO V1.1 LTE 2x1W B3/B7 equipment shall beperformed in accordance with all applicable manufacturer's recommendations, andnational laws and regulations. In particular:•Workers that are required to work in close proximity to the equipment, for examplemaintenance personnel, should strictly follow instructions provided by their employer.•Workers equipped with personal medical electronic devices, such as pacemakers andhearing aids, shall consult the manufacturer's instructions and consult theiroccupational health practitioner.Europe and countries with ICNIRP based regulations:Alcatel-Lucent 9764 MCO LTE B3According to the results of the SAR assessment of the Alcatel-Lucent 9764 MCO LTEB3, the installation shall at least adhere to the following recommendations:•The equipment shall be installed in a location restricting access by the general publicto the area within 70 millimeters directly in front of the equipment shroud at fulltransmit power. One practical implementation of this requirement is to ensure that theequipment is mounted a minimum of 3 meters above local ground, this verticaldistance being measured from the local ground or closest walkway to the bottom ofthe equipment.•The compliance distance with the ICNIRP/EU exposure limits values for workers is20 mm at full transmit power. The equipment shall be powered off before anyoperation or maintenance in the close vicinity of the shroud.•The operator or the entity putting the equipment into service shall stick the ISO3866-2 warning label (cf. 2013/35/EU, 92/58/ECC & 2007/30/EC) provided togetherwith the equipment according to manufacturer’s instructions before the first powerswitch on.According to the results of the SAR assessment of the Alcatel-Lucent 9764 MCO LTEB3, touch safe conditions for workers are achieved if the Tx power is less than or equal to2*0.38 W and touch safe conditions for general public are achieved if the Tx power is lessthan or equal to 2*0.076 W.For further information on RF exposure, the following table provides indicative values ofelectromagnetic field reference levels in the main lobe in front of the antenna:Table C-1 Distances corresponding to reference levels for the general public andworkers at maximum Tx powerPTX max (2*1 W) Electric field(V/m)Distance from theshroud (m)ICNIRP reference level and EU action levelfor workers130 0.13Product conformance statementsEuropean UnionProduct safety and RF exposure........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-11DRAFTDRAFT
Table C-1 Distances corresponding to reference levels for the general public andworkers at maximum Tx power (continued)PTX max (2*1 W) Electric field(V/m)Distance from theshroud (m)EU/ICNIRP reference level for the generalpublic58 0.32Alcatel-Lucent 9764 MCO LTE B7According to the results of the SAR assessment of the Alcatel-Lucent 9764 MCO LTEB7, the installation shall at least adhere to the following recommendations:•The equipment shall be installed in a location restricting access by the general publicto the area within 90 millimeters directly in front of the equipment shroud at fulltransmit power. One practical implementation of this requirement is to ensure that theequipment is mounted a minimum of 3 meters above local ground, this verticaldistance being measured from the local ground or closest walkway to the bottom ofthe equipment.•The compliance distance with the ICNIRP/EU exposure limits values for workers is10 mm at full transmit power. The equipment shall be powered off before anyoperation or maintenance in the close vicinity of the shroud.•The operator or the entity putting the equipment into service shall stick the ISO3866-2 warning label (cf. 2013/35/EU, 92/58/ECC & 2007/30/EC) provided togetherwith the equipment according to manufacturer’s instructions before the first powerswitch on.According to the results of the SAR assessment of the Alcatel-Lucent 9764 MCO LTEB7, touch safe conditions for workers are achieved if the Tx power is less than or equal to2*0.66 W and touch safe conditions for general public are achieved if the Tx power is lessthan or equal to 2*0.13 W.For further information on RF exposure, the following table provides indicative values ofelectromagnetic field reference levels in the main lobe in front of the antenna:Table C-2 Distances corresponding to reference levels for the general public andworkers at maximum Tx powerPTX max (2*1 W) Electric field(V/m)Distance from theshroud (m)ICNIRP reference level and EU action levelfor workers140 0.1EU/ICNIRP reference level for the generalpublic61 0.4Product conformance statementsEuropean UnionProduct safety and RF exposure........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-12 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Eco-environmental statementsPackaging collection and recovery requirementsCountries, states, localities, or other jurisdictions may require that systems be establishedfor the return and/or collection of packaging waste from the consumer, or other end user,or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for thereturn and/or collection of the packaging waste may be established. For more informationregarding collection and recovery of packaging and packaging waste within specificjurisdictions, contact the Alcatel-Lucent Environment, Health and Safety organization.Recycling / take-back / disposal of productsIn compliance with Waste Electrical and Electronic Equipment Directive (WEEEDirective) 2002/96/EC 01/2003, amended by WEEE Directive 2003/108/EC 12/2003,electronic products bearing or referencing the symbols shown below shall be collectedand treated at the end of their useful life, in compliance with applicable European Unionand other local legislation. They shall not be disposed of as part of unsorted municipalwaste. Due to materials that may be contained in the product, such as heavy metals, theenvironment and human health may be negatively impacted as a result of inappropriatedisposal.Note 1: For electronic products put on the market in the European Union, a solid barunder the crossed-out wheeled bin indicates that the product was put on the market after13 August 2005.Moreover, in compliance with legal requirements and contractual agreements, whereapplicable, Alcatel-Lucent will offer to provide for the collection and treatment ofAlcatel-Lucent products bearing the logo at the end of their useful life, or productsdisplaced by Alcatel-Lucent equipment offers.For information regarding take-back of equipment by Alcatel-Lucent, or for moreinformation regarding the requirements for recycling/disposal of a product, please contactyour Alcatel-Lucent account manager. Visit the Alcatel-Lucent Take-Back(http://www.alcatel-lucent.com/product_takeback) web page, or contact Alcatel-LucentProduct conformance statementsEuropean UnionEco-environmental statements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction C-13DRAFTDRAFT
Takeback Support at (mailto:takeback@alcatel-lucent.com). For technical information onproduct treatment, consult the Alcatel-Lucent Recycling Information (http://www.alcatel-lucent.com/product_recycling) web page.Material content complianceEuropean UnionThe European Union (EU) Restriction of the Use of Certain Hazardous Substances inElectrical and Electronic Equipment (RoHS) Directive [2002/95/EC and its recast2011/65/EU] as amended restricts the use of lead, mercury, cadmium, hexavalentchromium, and polybrominated biphenyls and polybrominated diphenyl ethers inelectrical and electronic equipment. This Directive applies to electrical and electronicproducts placed on the EU market after 1 July 2006, with various exemptions, includingan exemption for lead solder in network infrastructure equipment. Alcatel-Lucentproducts shipped to the EU after 1 July 2006 comply with the EU RoHS Directive.EU REACHOn June 1, 2007, European Regulation No 1907/2006 on the Registration, Evaluation,Authorisation and Restriction of Chemicals (REACH) entered into force. Under REACH,companies operating in the EU may face certain obligations as manufacturers, importersand/or downstream users.Alcatel-Lucent complies with the current requirements of REACH. In particular, Article33 of REACH requires suppliers to inform the recipients and consumers if an articlereceived contains more than 0.1% (by weight per article) of any substance(s) on theSubstances of Very High Concern (SVHC) candidate list. Alcatel-Lucent has verified theuse of substances listed on the candidate list of Substances of Very High Concern aspublished on the ECHA website. Based on information received from our supply chainwe have no indication that any of the listed substances are present in any of our products,subassemblies or expansion items over 0.1% weight for weight. We will continue tomonitor the status of the candidate list as part of our ongoing compliance activities.Product conformance statementsEuropean UnionEco-environmental statements........................................................................................................................................................................................................................................................................................................................................................................................................................................................................C-14 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Appendix D: Document issuehistoryOverviewPurposeThis chapter provides the reissue history of this document.ContentsDocument issue history D-2...................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction D-1DRAFTDRAFT
Document issue historyPurposeThe reissue history of this document is described in the following paragraphs.Issue 3.03 (September 2014)The document changes from Issue 3, August 2014 are shown in the following table:Table D-1 Document changes from Issue 3, September 2014Feature/enhancement Description LocationDocumentation changes9764 MCO V1.1B2/B25 LTE 2x1WmodelAdded information regarding the B2/B25(combined) MCO.“Supported installation options” (p. 2-13)“Product features and capabilities” in“Functional description” (p. 2-2)“Alcatel-Lucent 9764 Metro Cell OutdoorLTE overview” and “Product labelling” in“Physical description” (p. 2-4)Pole mount options in:“Pole mountinstallation requirements” (p. 3-5)Wall mount in a pair configuration:Procedure3-6: “Wall mount the 9764 Metro Dock in apair configuration” (p. 3-71)Issue 3 (August 2014)The document changes from Issue 2, June 2014 are shown in the following table:Table D-2 Document changes from Issue 2,June 2014Feature/enhancement Description LocationDocumentation changesMCO to MetroDockattachment procedureAdded rotation angles for key and detailedgraphicsProcedure 4-5: “Attach 9764 MCO module to9764 Metro Dock” (p. 4-41)MCO module groundcablingAdded new step to ensure that the power isoff before performing the procedureProcedure 4-3: “9764 MCO module groundcabling” (p. 4-18)Physical description Update to the AC power surge protection “Physical description” (p. 2-4)Product powerrequirementsUpdate to the AC and DC electrical ratingin order to align with the product labelspecification.Update to the statement regarding aboutpower related ancillary items.“Product power requirements” (p. 4-27)Pre-installationinformationAdded the DC power connector type “Pre-installation information” (p. 4-3)Document issue history Document issue history........................................................................................................................................................................................................................................................................................................................................................................................................................................................................D-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Table D-2 Document changes from Issue 2,June 2014 (continued)Feature/enhancement Description LocationInstallationprocedures for the9764 MCO LTE2x2WAdded procedure for the installation of theRF antennaAdded procedure for the installation of theGPS antennaProcedure 4-1: “Connect external RF antennato the Alcatel-Lucent 9764 MCO LTE 2x2W”(p. 4-5)Procedure 4-2: “Connect GPS antenna”(p. 4-7)Pair-mountinstallation optionsAdded pair-mount information throughoutthe document.“Supported installation options” (p. 2-13)“Pole mount installation requirements”(p. 3-5)“Wall mount installation requirements”(p. 3-9)Issue 2 (June 2014)The document changes from Issue 1.06, May 2014 are shown in the following table:Table D-3 Document changes from Issue 1.06, May 2014Feature/enhancement Description LocationDocumentation changesExternal GPS antenna Added 26/40 dB antenna selection rule and warning reproximity to other antennas; updated purpose andprocedure selection table.Procedure 4-2: “Connect GPSantenna” (p. 4-7)Power up procedure Added procedure for powering on and troubleshootingthe MCOProcedure 4-8: “Power on the9764 MCO” (p. 4-52)Issue 1.06 (May 2014)The document changes from Issue 1.05, May 2014 are shown in the following table:Table D-4 Document changes from Issue 1.05, May 2014Feature/enhancement Description LocationFeaturesInternal surge arrestor Updates for internal surge arrestor for electrical Ethernet “Hardware and ancillary items”(p. 2-17),“Install optionalinternal surge arrestor”(p. 3-102)Documentation changesDocumentationstandards updateImplementation of the new documentation standard forthe “What's new” block (replaces the former “Reason forreissue” block).“What's new” (p. xiii)Sealing gasketlubricationUpdates to MCO attachment procedure to include gasketlubrication step and new graphics and clarificationsProcedure 4-5: “Attach 9764MCO module to 9764 MetroDock” (p. 4-41)Document issue history Document issue history........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction D-3DRAFTDRAFT
Table D-4 Document changes from Issue 1.05, May 2014 (continued)Feature/enhancement Description LocationLED location Added graphic to show location of LED “LED status for 9764 MCOLTE” (p. A-2)Issue 1.05 (May 2014)The document changes from Issue 1.04, May 2014 are shown in the following table:Table D-5 Document changes from Issue 1.04, April 2014Feature/enhancement Description LocationDocumentation changesESD wrist strap Added ESD wrist strap attachment step at the beginningof relevant procedures“9764 Metro Dock cabling”(p. 3-89)Issue 1.04 (April 2014)The document changes from Issue 1.03, February 2014 are shown in the following table:Table D-6 Document changes from Issue 1.03, February 2014Feature/enhancement Description LocationFeaturesConformancestatementsProduct conformance statements for MCO B3 and B7variants“Product safety and RFexposure” (p. C-10)Issue 1.03 (February 2014)The document changes from Issue 1.02, January 2014 are shown in the following table:Table D-7 Document changes from Issue 1.02, January 2014Feature/enhancement Description LocationFeaturesInternal GPS antenna Updates for internal GPS antenna solution “Physical description” (p. 2-4),Procedure 4-2: “Connect GPSantenna” (p. 4-7)Document issue history Document issue history........................................................................................................................................................................................................................................................................................................................................................................................................................................................................D-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Issue 1.02 (January 2014)The document changes from Issue 1.01, December 2013 are shown in the following table:Table D-8 Document changes from Issue 1.01, December 2013Feature/enhancement Description LocationDocumentation changesWi-Fi AP LED Updates to Wi-Fi AP LED state table “LED status for 9764 MCOLTE” (p. A-2)Issue 1.01 (December 2013)The document changes from Issue 1, November 2013 are shown in the following table:Table D-9 Document changes from Issue 1, November 2013Feature/enhancement Description LocationFeaturesPair mount and daisychainPair-mount and daisy chain installation configurations “Supported installationoptions” (p. 2-13),Chapter 3,“Installation of the 9764 MetroDock”Wi-Fi AP Wi-Fi AP installation procedures “Supported installationoptions” (p. 2-13),Appendix B,“Installation of the 9764 MCOWi-Fi AP”Issue 1Issue 1, November 2013, was the first publication of this document in support of theproduct's first commercial availability in LR13.3.L.Document issue history Document issue history........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction D-5DRAFTDRAFT
Document issue history Document issue history........................................................................................................................................................................................................................................................................................................................................................................................................................................................................D-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Glossary...................................................................................................................................................................................................................................Numerics3GPP3rd Generation Partnership Project...................................................................................................................................................................................................................................A A (Ampere)Base SI unit of electrical current.AC (Alternating Current)Continuously variable current, rising to a maximum in one direction, falling to zero, thenreversing direction and repeating the cycle in the other direction.AC convenience outletSites must be equipped with at least two duplex outlets for installation and maintenanceprocedures. The outlets are required to power test equipment and installation tools.Ambient temperatureThe temperature of air or other media in a designated area, particularly the areaANSI (American National Standards Institute)An organization chartered to accredit standards developed by a wide variety of industry groups,without influence from any one company or organization. Does not develop standards, butreviews and implements those developed by other organizations. ANSI is a member of theInternational Standards Organization (ISO).AntennaAn elevated device for radiating or receiving radio waves. It changes electrical currents intoelectromagnetic waves, and vice versa.APAccess PointAWG (American Wire Gauge)American standard for classifying wire diameter....................................................................................................................................................................................................................................B BackupFacility used to replace an element which has failed.....................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction GL-1DRAFTDRAFT
Base stationThe equipment that provides the air interface that allows mobile terminals to communicate withthe telecommunications network.BBUBaseBand UnitBOCABuilding Officials and Code AdministratorsBondingPermanent connection of metallic parts to form an electrically conductive path that will assureelectrical continuity and have the capability to safely conduct any current likely to be imposed.Branch circuitThe circuit conductors between the final overcurrent device protecting the circuit and theoutlet(s).Breaker, circuitA cut-out device which breaks a circuit when preset limits of current are exceeded.Buried ring groundA buried, bare, tinned, solid copper cable encircling the site building and/or tower foundation....................................................................................................................................................................................................................................C CDRHCenter for Devices and Radiological HealthCell siteAn installation located within a cell that houses the equipment needed to set up and complete callson a cellular telephone.CIC ((Customer Information Center))Source for locating and obtaining delivery of Alcatel-Lucent customer documents.Circuit1. The complete path between two terminals over which one-way or two-way communicationsmay be provided. 2. An electronic path between two or more points, capable of providing anumber of channels. 3. A number of conductors connected together for the purpose of carrying anelectrical current. 4. An electronic closed-loop path among two or more points used for signaltransfer. 5. A number of electrical components, such as resistors, inductances, capacitors,transistors, and power sources connected together in one or more closed loops.ConfigurationAn arrangement of functional units according to their nature, number, and chief characteristics.Glossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................GL-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Controlled environmentAn indoor location in which temperature, humidity, and ventilation are maintained at specificlevels.CPRI (Common Public Radio Interface)Specification for the key internal interface of radio base stations between the Radio EquipmentControl (REC) and the Radio Equipment (RE).CSA (Canadian Standards Association)An independent, non-government, not-for-profit association for the development, by consensus,of Canadian standards and product certifications.CSC (Cell Site Configuration)Sheets provided in this document for documenting cell site configuration, conditions, and otherpertinent information for reference during product deployment, and future additions....................................................................................................................................................................................................................................D dB (Decibel)A unit which expresses the ratio of two voltages, currents, or powers. It is used to specifytransmission loss, gain, or relative level. It is equal to 20 times the common logarithm of the ratioof two voltages or two currents, or 10 times the common logarithm of the ratio of two powers.DC (Direct Current)Current flow in one direction.DiversityA method of radio transmission and/or reception, which counteracts the effects of fading bycombining several signals all bearing the same information.Driven ground rodA copper-clad steel or stainless steel rod, a minimum of 2.4 meters (8 feet) long and 5/8 inch indiameter....................................................................................................................................................................................................................................E Earthquake zoneSeismic ratings ranging from zone 1 (relatively low central office operational shock and vibrationlevels) to the most severe zone 4 levels. Equipment must be able to withstand earthquake zonerequirements under both operational and non-operational conditions.Electrolytic ground rodA low resistance grounding rod (pipe) using low resistivity materials.EUEuropean UnionGlossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction GL-3DRAFTDRAFT
Exothermic weldA method of making electrical connections of copper to copper or copper to steel using hightemperature fusion. The molten copper flows over conductors in a mold, melting and weldingthem together....................................................................................................................................................................................................................................F FacilityAny element of physical telephone equipment needed to provide service, such as cables,switching systems, and microwave radio transmission systems.FCC (Federal Communications Commission)A group founded in 1934 to regulate all types of communications in the United States.FDAFood and Drug AdministrationFrequencyFor a periodic wave, such as alternating current, the number of complete cycles per unit of time.The unit of frequency is cycles per second, or hertz.FuseAn overcurrent protective device that has as its critical component a metal wire or strip that willmelt when heated by a prescribed (design) amperage, creating an open in the circuit of which it isa part, thereby protecting the circuit from an overcurrent condition....................................................................................................................................................................................................................................G GainThe ratio of output current, voltage, or power to input current, voltage, or power, respectively.Gain is usually expressed in dB. If the ratio is less than unity, the gain, expressed in dB, will benegative, in which case there is a loss between input and output.GBEGigaBit EthernetGFCI (Ground Fault Circuit Interrupter)A device intended for protection of personnel that functions to de-energize a circuit or portionthereof within an established period of time when a current to ground exceeds somepredetermined value that is less than that required to operate the overcurrent protective device ofthe supply circuit.GPS (Global Positioning System)A system of 24 satellites that provides, among other things, extremely accurate timing informationto the cell sites.GroundA conducting connection between equipment or an electrical circuit and earth, or conductive bodythat is used in place of earth.Glossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................GL-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
Ground conductorA conductor used to connect equipment or a grounded electrical circuit to the grounding electrodesystem.Grounding electrode systemThe conductive objects that are intentionally bonded to furnish connection to earth (i.e., buriedring ground with ground rods, electrically continuous buried metallic water pipe, electrolyticground electrode, etc.).GuySteel wire or rope used to hold a pole upright....................................................................................................................................................................................................................................H Heat dissipationThe heat generated by equipment during operation.HSDPAHigh Speed Downlink Packet AccessHSUPAHigh Speed Uplink Packet AccessHVHigh VoltageHz (Hertz)A unit of frequency of a periodic process equal to one cycle per second....................................................................................................................................................................................................................................I ICNIRPInternational Commission for Non-Ionizing Radiation ProtectionIEEEInstitute of Electrical and Electronics EngineersINTR (Intrusion Alarm)The Intrusion (INTR) alarm indicates a door or access panel to the power system is open.ITIn an IT earthing system, the electrical distribution system has no connection to earth at all, or ithas only a high impedance connection. In such systems, an insulation monitoring device is used tomonitor the impedance....................................................................................................................................................................................................................................L LANLocal Area NetworkGlossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction GL-5DRAFTDRAFT
LoadThe power consumed by a device or circuit in performing its function.LossThe diminution, usually expressed in dB, of signal level in a communications medium. Thepower, usually expressed in watts, consumed by a circuit or component. The energy dissipatedwithout accomplishing useful work or purpose.LVLow Voltage...................................................................................................................................................................................................................................M MHz (Megahertz)Reference of radio frequency spectrum of one-million cycles.MOP (Method of Procedure)Cell site walk-through where site preparation activities are verified prior to installing the 9412eNodeB Compact equipment.MSPMobile Service Provider...................................................................................................................................................................................................................................N NEC (National Electric Code)Standard that governs the use of electric wire, cable, and fixtures, and electrical and opticalcommunication cable installed in buildings.NetworkA set of terminals, the communications link that joins them, and the protocols that allow them tofunction together and communicate with each other.NFPA (National Fire Protection Association)Standards and code writing organization made up of volunteer industrial and institutionalsubject-matter-expert committees.NFPANational Fire Protection AssociationNominalSpecified value or intended value independent to any uncertainty in its realization. In a device thatrealizes a physical quantity, it is the value of such a quantity specified by the manufacturer.Non Alcatel-Lucent power3rd party power systems, or power systems other than Alcatel-Lucent.Glossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................GL-6 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
...................................................................................................................................................................................................................................P PhaseThe number of separate voltage waves in commercial alternating current, designated as "singlephase", "three phase", etc....................................................................................................................................................................................................................................Q QAMQuadrature Amplitude ModulationQoEQuality Of Experience...................................................................................................................................................................................................................................R RCDResidual Current DeviceRF (Radio Frequency)Electromagnetic wave used for, among other things, cellular voice and data communications.RMS (Root Mean Square)Effective value of an alternative wave. For AC, this is numerically equal to DC value of thecurrent with the same heating effect.RoHSRestriction of Hazardous SubstancesRx (Receive)...................................................................................................................................................................................................................................S SAR (Specific Absorption Rate)A measure of the rate at which energy is absorbed by the body when exposed to radio frequencyenergy.SectorThe coverage area within the degree of directionality of the antennas.SFPSmall Form-Factor Pluggable (a transceiver module)ShieldA housing, screen, sheath, or cover that substantially reduces the coupling of electric, magnetic, orelectromagnetic fields into or out of circuits or transmission lines.SiteAn installation that houses the equipment needed to set up and complete calls on a cellulartelephone.Glossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction GL-7DRAFTDRAFT
Site preparationTo perform the requirements necessary at the site before installation can begin.StrandedWires twisted together to form a strong flexible cable.Surge protectorProtective device used to limit surge voltages by discharging or bypassing any unwanted surgecurrent that may enter a building or equipment....................................................................................................................................................................................................................................TT1A four-wire voice and data trunking facility that carries 24 duplex channels over 56-kbps timeslots.TNIn a TN earthing system, one of the points in the generator or transformer is connected with earth,usually the star point in a three-phase system. The body of the electrical device is connected withearth via this earth connection at the transformer.TTIn a TT earthing system, the protective earth connection of the consumer is provided by a localconnection to earth, independent of any earth connection at the generator.Twisted pair cableCable made up of one or more separately insulated twisted-wire pairs, none of which is arrangedwith another to form quads.Tx (Transmit)...................................................................................................................................................................................................................................U UBCUniform Building CodeUL (Underwriters Laboratories)Laboratories that test and approve materials and equipment against pre-determined performancestandards....................................................................................................................................................................................................................................V V (Volt)The derived SI unit of electrical potential difference. It is the difference in potential between twopoints of a conducting wire carrying a constant current of 1 ampere when the power dissipatedbetween these two points is equal to 1 watt.V AC (Volts Alternating Current)V DC (Volts Direct Current)Glossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................GL-8 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
V rms (Volts Root Mean Square)VSWR (Voltage Standing Wave Ratio)In a transmission line, the ratio of maximum to minimum voltage in a standing wave pattern. TheVSWR is a measure of impedance mismatch between the transmission line and its load. Thehigher the VSWR, the greater the mismatch. The minimum VSWR, i.e., that which corresponds toa perfect impedance match, is unity....................................................................................................................................................................................................................................W W (Watts)The derived SI unit of power. It is equivalent to 1 joule per second, or 1 volt-ampere.Walk-throughA critical examination of a design or product undertaken to ensure that it is of adequate quality.WaveformThe characteristic shape of a periodic wave, determined by the frequencies present and theiramplitudes and relative phases.WCDMAWideband Code Division Multiple AccessWEEEWaste Electrical and Electronic EquipmentGlossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction GL-9DRAFTDRAFT
Glossary........................................................................................................................................................................................................................................................................................................................................................................................................................................................................GL-10 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
IndexNumerics9764 MCO moduleadditional optional items, 4-3pre-installation, 4-3product delivery contents, 4-3remove, B-9tools, 4-39764 MCO Wi-Fi AP, B-2,B-259764 MCO Wi-Fi AP - PhysicaldescriptionAntennas, B-6Connection interfaces, B-4Debug interface, B-6Product base items andconfigurations, B-4Product labeling, B-6Product overview, B-2.............................................................Aadditional optional items9764 MCO module, 4-3Metro Dock, 3-3Wi-Fi AP, B-8AntennaGPS antenna, 2-11RF antenna, 2-10Attach9764 MCO moduleattach to 9764 Metro Dock,4-41auto-commissioning, 4-51.............................................................Ccabling, 4-29CE marking, C-8Connect external RF antenna, 4-5Connect GPS antenna, 4-7Connectors, 2-8.............................................................DDaisy chainingconfigurations, 3-15device placementMetro Cell, 3-3document support, xix.............................................................EElectrical Ethernet cabling, 3-99EMC compliance, C-9.............................................................FFinal installation activities andchecks, 3-112.............................................................Gglossary, GL-1GPS antenna, 4-12,4-15internal, 4-14GroundingMCO module, 4-18.............................................................HHardware and ancillary items9764 MCO Wi-Fi AP, 2-179764 Metro Cell Module baseitems, 2-179764 Metro Dock base items,2-17Ethernet cable (electrical),2-19Ethernet cable (optical), 2-19External antenna - GPS, 2-21External RF antenna, 2-22Grounding, 2-18Installation kits, 2-17Pair-mount configuration, 2-22Power, 2-18SFP modules, 2-18Surge arrestor, 2-19.............................................................IInstallation kitsfor pole mount, 3-6for wall mount, 3-9....................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction IN-1DRAFTDRAFT
Internal surge arrestorInstallation, 3-102.............................................................LLED9764 MCO LTE, A-29764 MCO LTE 2x1W,location, A-2LED state description, A-1LED status9764 MCO Wi-Fi AP, B-25.............................................................MMaterial content compliance, C-14MCO module ground cabling,4-18Metro Celldevice placement, 3-3pre-installation, 3-3Metro Cell Moduleconnectors, 2-8overview, 2-6status indicator, 2-12Metro Cell OutdoorGPS antenna, 2-11physical description, 2-4power supply, 2-10product labelling, 2-12RF antenna, 2-10weights and dimensions, 2-5Metro Dockadditional optional items, 3-3product delivery contents, 3-3Standard wall mount, 3-36tools, 3-4Metro Dock cablingConnect the electrical Ethernetcable, 3-104Connect the ground cable, 3-90Connect the optical Ethernetcable, 3-95mount the surge arrestor, 3-109Metro Dock Ethernet cabling, 3-92Metro Dock ground cabling, 3-90Metro Dock pole mountusing bands, 3-21using screws, 3-20Metro Dock pole mount usingbands, 3-21Metro Dock pole mount usingscrews, 3-20.............................................................OOrient 9764 MCO module, 4-48.............................................................PPackaging collection and recoveryrequirements, C-13Pair-mountPhysical dimensions, 2-6with daisy chaining, 3-13without daisy chaining, 3-14phone numbersfor document support, xixPhysical description, 2-49764 MCO Wi-Fi AP, B-2Pole mountexamples, 3-7installation kits, 3-6options, 3-5post installation checks, 4-51Power - productancillary items, 4-27connection point, 4-28Power connector, assemble, 4-30,4-34Power cord, connect, 4-33,4-38power on, 4-52Power requirementsProduct power specification,4-27Power requirements (AC)AC power supply, 4-21Conduit, 4-23General, 4-21Line surge protection, 4-22Power junction box, 4-22Power requirements (DC)Conduit, 4-25DC power supply, 4-24General, 4-24Line surge protection, 4-25Power Junction box, 4-25Power supply, 2-10pre-installation9764 MCO module, 4-3Metro Cell, 3-3Wi-Fi AP, B-8product conformance statements,C-1product delivery contents9764 MCO module, 4-3Metro Dock, 3-3Wi-Fi AP, B-8Product features and attributes, 2-2Index........................................................................................................................................................................................................................................................................................................................................................................................................................................................................IN-2 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT
product labeling9764 MCO Wi-Fi AP, B-6product labelling, 2-12Product safety, C-10.............................................................RRadio spectrum compliance, C-9Recycling / take-back / disposal ofproducts, C-13RF exposure, C-4,C-10.............................................................SStandard wall mount, 3-36status indicator, 2-12Supported installation optionsDaisy chain, 2-14Pair-mount, 2-15Standard, 2-13.............................................................Ttools9764 MCO module, 4-3Metro Dock, 3-4Wi-Fi AP, B-8.............................................................WWall mount, 3-40examples, 3-11installation kits, 3-9options, 3-9Weights and dimensions, 2-5Wi-Fi APadditional optional items, B-8attach to MCO module, B-19installation, B-19optional, B-1pre-installation, B-8product delivery contents, B-8tools, B-8with optional tilt brackets, 3-40Index........................................................................................................................................................................................................................................................................................................................................................................................................................................................................Alcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014Alcatel-Lucent – InternalProprietary – Use pursuant to Company instruction IN-3
Index........................................................................................................................................................................................................................................................................................................................................................................................................................................................................IN-4 Alcatel-Lucent – InternalProprietary – Use pursuant to Company instructionAlcatel-Lucent 9764 MCO3MN-01707-0002-RJZZAIssue 3.05 October 2014DRAFTDRAFT

Navigation menu