Nortek Security and Control 00170 Grill Guard User Manual GC GRILL1 B 345 10017336 X16 indd

Nortek Security & Control LLC Grill Guard GC GRILL1 B 345 10017336 X16 indd

User Manual

1 Copyright © 2017 Nortek Security & Control LLC GC-GRILL1-B-345 GRILL GUARDINSTALLATION INSTRUCTIONSThe GoControl® Grill Guard (device) is a contact ON/OFF sensor that alerts your security panel (and op onally the smartphone with Alarm.com) when the knob on a grill/stove is turned ON. It is compa ble with 2GIG security panels, including GC2, GC3, and Vario.INNER MARKS KNOB STEM SLEEVEMAGNET GRILLKNOB DISC Figure 1. Grill Knob Device Assembly ContentsVerify that the package contains the following: •One (1) Grill Guard disc - w/ pre-installed ba eries and adhesive strips a ached •Knob stem sleeves w/magnets – 3 diff erent sizesPre-Installation ChecksBefore installa on:1. Ensure the device (grill, stove, heater, etc.) is turned OFF. If possible, also turn OFF the gas valve and/or the power source.2. Ensure the grill/stove surface around the knob is fl at, enabling the disc to be a ached.3. If a trim ring around the knob is on the surface, ensure the inner diameter of the ring is no smaller than 2.5 inches.4. Ensure the knob stem has adequate length for allowing inser ng the Grill Guard disc on the knob at least 0.2 inches above its usual “all-the-way-in” posi on on the knob stem, allowing the grill knob to operate properly.Installation1. Ensure the knob where you are installing the Grill Guard is turned to the OFF posi on.2. Remove the knob from the grill/stove. Note: If necessary, remove the knob trim ring.3. Ensure the grill/stove surface around the knob area is clean.4. Iden fy the sleeve that best fi ts your knob stem, from the three provided.1. 2. 3.Notes: •The sleeve orienta on for your grill/stove knob stem may require fl ipping a sleeve over. •If the knob stem protrudes too far, try using the cavity-backed sleeve (3.). •If the sleeve or knob has a loose fi t or the sensor alignment is off , use a small amount of duct tape or electrical tape to make it snug.5. Install the sleeve onto the knob stem, following the orienta on, as shown in Step 4. Note: Ensure the bo om of the sleeve magnet has a clearance of 0.1 inches from the knob panel surface.6. Remove the Signal Suppression Tape from the disc to ac vate the sensor located inside the disc.ADHESIVE STRIPSSIGNAL SUPPRESSION TAPE7. Remove the visible protec ve backing material from each adhesive strip.8. Align the inner marks on the disc with the magnet on the sleeve and mount the disc to the grill/stove face. INNERMARKS MAGNETSLEEVE9. Install the grill knob back onto the knob stem.10. Use your Panel to program the Grill Guard.Programming the Device on the GC2/GC2 PanelFor GC2 and GC3 panels, program the Grill Guard on your 2GIG panel with the following parameters. (Please refer to your panel’s quick programming guide for the actual steps.)Sensor Type: (23) No Response TypeSensor Equipment Type: Contact Equipment Code: (0862) 2GIG Thin Door/Window Contact1Serial Number: [Input the unique 7-digit TXID.]2Equipment Age: NewSensor Loop Number: 2Dialer/Transmission Delay: EnabledVoice Descriptor: GAS LEFT ON3Sensor Reports: EnabledSensor Supervised: Disabled4Sensor Chime: [User-specifi ed]1 This is a provisional Equipment Code. A new category called “Grill Guard” (or similar name) will be added in a future GC2/GC3 panel update.2 Alterna vely, a Grill Guard can be automa cally learned in.3 This is a recommended voice descriptor. The user may defi ne a custom voice descriptor, as needed.4 Choose Disabled if the user plans on taking the grill/stove away from the premises from  me to  me. Otherwise, choose Enabled.PRINTER’S INSTRUCTIONS:INSTR,INSTL GC-GRILL1-B-345 - P/N: 10017336 X16 INK: BLACK - MATERIAL: 16 LB. MEAD BOND - SIZE: 6.000” X 9.000” - TOL: +/- 0.125”- SCALE: 1-1 - FOLDING: 4X TO 1.5” x 2.25” - FINISH WITH LOGO SHOWING - SIDE 1 OF 2
2 Copyright © 2017 Nortek Security & Control LLC Programming the Device on the Vario PanelFor the Vario panel, a er learning in1 the Grill Guard, pleaseconfi gure the zone the Grill Guard is in with the followingparameters:Zone Type: Output TriggerZone Sound Armed Away: SilentZone Sound Armed Stay: SilentZone Sound Disarmed: Chime or Silent1If you want to manually program the Grill Guard in the Vario panel using the TXID, convert the GC2/GC3 TXID, as follows, to obtain the Vario TXID.Example: GC2/GC3 TXID = 080-9665, Vario TXID = 809,665 + 11,602,097,152 = 11,602,906,817Setting up E-mail Notification – Alarm.com Accounts Only1. Navigate to hƩ p://www.alarm.com and click LOGIN.2. Your systems dashboard page will appear. Select the Security tab and click Sensors.3. Iden fy the new sensor you added. You can rename theSensor Name. When fi nished, click Save.4. Click the NoƟ fi caƟ ons tab, and then +New NoƟ fi caƟ onbu on to create a new event. The menu will appear withthe Standard tab open by default.5. Click Sensor LeŌ Open. Add parameters. Also, click +Add Recipient to add recipients associated with the no fi ca on.6. Click Close when names have been selected, then click Save NoƟ fi caƟ on.Specifications •Signal Range: 100  . open-air from a 2GIG panel •Transmission Frequency: 345 MHz •Disc dimensions: 2.2” diameter, 0.21” thickness •Opera ng Temperature: 14°F to 167°F (-10°C to 75°C)FCC & IC NoticeThis device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s). Opera on is subject to the following two condi ons:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference received that may cause undesired opera on.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploita on est autorisée aux deux condi ons suivantes:(1) l’appareil ne doit pas produire de brouillage, et(2) l’u lisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscep ble d’en comprome re le fonc onnement.This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al installa on.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ons may cause harmful interference to radio communica ons. However, there is no guarantee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to radio or television recep on, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separa on between the equipment and receiver• Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician to help.WARNINGS:• Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.• The Grill Guard is not intended as a life-safety device. It is not intended to replace any other safety considerations.Limited WarrantyThis Nortek Security & Control product is warranted against defects in material and workmanship for 6 months. Nortek Security & Control does not warrant this product to consumers.There are no obliga ons or liabili es on the part of Nortek Security & Control for consequen al damages arising out of or in connec on with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal, installa on, or reinstalla on. All implied warran es for func onality, are valid only un l the warranty expires. This Nortek Security & Control LLC Warranty is in lieu of all other warran es expressed or implied.Nortek Security & Control LLC2GIG1950 Camino Vida Roble, Suite 150Carlsbad, CA 92008-6517 USAFor technical support in the USA and Canada:800.421.1587Email: 2gigtechsupport@nortek.comVisit www.nortekcontrol.com for technical support hours of opera onFor technical support outside of the USA and Canada:Contact your regional distributorVisit dealer.2gig.com for a list of distributors in your region PRINTER’S INSTRUCTIONS:INSTR,INSTL GC-GRILL1-B-345 - P/N: 10017336 X16 INK: BLACK - MATERIAL: 16 LB. MEAD BOND - SIZE: 6.000” X 9.000” - TOL: +/- 0.125”- SCALE: 1-1 - FOLDING: 4X TO 1.5” x 2.25” - FINISH WITH LOGO SHOWING - SIDE 2 OF 210017336 X16

Navigation menu