Nutek ATNG Transmitter User Manual

Nutek Corporation Transmitter Users Manual

Users Manual

128-92971 of 41PATENTED: www.voxxintl.com/company/patentsFEATURES : 2 Programmable RF TransmitterSingle Channel Receiver (capable of accepting 4 transmitters)External Receiver Antenna w/PushButton Switch & LEDOn-Board Start RelayOn-Board Accessory RelayOn-Board Ignition 1 RelayOn-Board Ignition 2 RelayIgnition 2 Relay Selectable On or Off During CrankingOn-Board Parking Light RelayIgnition 3 / Shock By-Pass / GM VAT Output (relay required)Tach Signal Learning CircuitTwo ( + ) and Two ( - ) Safety Shutdown CircuitsAlarm By-Pass OutputAccessory Outputs (Pulse Before & After Start, During Crank & After Shut Down)Selectable Steady or Flashing Parking Lights for Run IndicationSelectable 5, 10, 15, 20, 45, and 60 Minute Run TimeCar Finder ModeOptional Door Unlock Feature For Vehicles Equipped With Power Doors (Only operational while running under control of the remote start unit.)Single Channel Remote Car StarterModel PRO9056EOwner’s Manual
128-92972 of 42REMOTE STARTING THE VEHICLEThis will not start the vehicle if any one of the following situations exists: The vehicle's hood lid is opened. The gear shift selector is not in Park. The brake pedal is depressed. The safety control switch is in the Off position.1) To start the vehicle, press and release the transmitter button two times within 2 seconds. The vehicle will start and remain running for the pre-programmed run cycle. As a visual indication, the parking lights will ash or remain on depending on the setting by your installation center.2) When you arrive at the vehicle, turn the ignition key to the ON position (not the spring loaded start position), then step on the brake pedal to disengage the remote starter. The vehicle will continue to run, but now on its own power.NOTE: The engine will stop running before the pre-programmed run cycle has expired if you perform any one of the following functions: -Press and the button on the keychain transmitter two times within 2 seconds-Depress the brake pedal-Open the vehicle's hood-Place the unit in the safety control disabled mode.PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL SWITCHThe Push-Button LED switch located in the receiver allows you to temporarily dis-able the remote starting function of the system. This recommended whenever the vehicle is being serviced. To place the system in the service mode:1) With the system disarmed/unlocked, and the ignition switch off, Press and Hold the Push-Button, found on the windsheild receiver, in.2) Turn the ignition switch on, off, on, off, on, off.3) The LED begins to ash two short ashes followed by one long ashes and continues this pattern until returned to normal mode of operation.This puts the unit into the R/S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or other-wise.To Exit R/S Override Mode1) With the system disarmed, Press and Hold the Push-Button, found on the windsheild receiver, in.2) Turn the ignition switch on, off, on, off, on, off.3) The LED turns off indicating that the R/S unit is fully functional once again.
128-92973 of 43UNLOCKING THE VEHICLE:If you have electric door lock, and the Optional Unlock feature was added, with the vehicle running under command of the remote start unit, press and hold the transmitter button for 3 seconds until the doors unlock.CAR FINDER MODE:Anytime the vehicle is not running under control of the remote start unit, within operating range of the vehicle, press and hold the push-button of the hand held transmitter for 4 seconds to activate the car nder mode. The vehicle lights will ash for 30 seconds or until the push-button is again pressed and released.TELEMATIC UPGRADE:This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that can give you control of certain functions of your vehicle from a Telephone, or in some cases a computer interface. Please check with your installation center for most recent Telematic Upgrades. If you had a Telem-atic Upgrade installed, the manual supplied with the upgrade unit will provide an operator's manual advising of the features of the system and means available to control these features of your vehicle.PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1)Transmitter Model Name, 141BPR Is Also Found On Back Of Transmitter Case. Use Battery CR20321) Turn the ignition key to the on position.2) Press and release the valet/programming switch 3 times (Siren Chirps).3) Press the Button of each transmitter you want programmed until you hear a chirp from the horn or siren.4) Turn the ignition switch off.The above action programs the Start button for the one button start systems. Note: Some systems will not have a audible sound associated with program-ming,,,for these systems the lights will ash.
128-92974 of 44To purchase replacement transmitters or to get additional product information go to: www.pursuitcarsecurity.com© 2014 Voxx Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-9297FCC COMPLIANCEThis device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including any interference that may cause undesired operation.Warning!Changes or modications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipmentNOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the equipmentTransmitter Battery Replacement1) Locate and remove the "00" point philips head screw on the back of the transmitter case.2) Carefully separate the front case from the rear.3) Slide the CR2032 battery out from under the battery clip and dispose of properly.4) Install the new battery with the (+) side facing up away from the circuit board.5) Close the case and reassemble in reverse of disassemblyFUNCTION SETTING CHARTTo be completed by installerRun Time 5 Min  10 Min  15 Min  20 Min  45 Min 60 MinWhile Running Unlock Yes  No  Lights Pulse  Steady 

Navigation menu