Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2340672 |
| Application ID | RA6/IrzlSisRbv4HPo2TLg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 15.22kB (190271 bits) |
| Date Submitted | 2014-07-30 00:00:00 |
| Date Available | 2014-07-30 00:00:00 |
| Creation Date | 2017-10-21 19:38:59 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-21 19:38:59 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Model PRO9056E Owner’s Manual Single Channel Remote Car Starter FEATURES : 2 Programmable RF Transmitter Single Channel Receiver (capable of accepting 4 transmitters) External Receiver Antenna w/PushButton Switch & LED On-Board Start Relay On-Board Accessory Relay On-Board Ignition 1 Relay On-Board Ignition 2 Relay Ignition 2 Relay Selectable On or Off During Cranking On-Board Parking Light Relay Ignition 3 / Shock By-Pass / GM VAT Output (relay required) Tach Signal Learning Circuit Two ( + ) and Two ( - ) Safety Shutdown Circuits Alarm By-Pass Output Accessory Outputs (Pulse Before & After Start, During Crank & After Shut Down) Selectable Steady or Flashing Parking Lights for Run Indication Selectable 5, 10, 15, 20, 45, and 60 Minute Run Time Car Finder Mode Optional Door Unlock Feature For Vehicles Equipped With Power Doors (Only operational while running under control of the remote start unit.) PATENTED: www.voxxintl.com/company/patents 128-9297 1 of 4 REMOTE STARTING THE VEHICLE This will not start the vehicle if any one of the following situations exists: The vehicle's hood lid is opened. The gear shift selector is not in Park. The brake pedal is depressed. The safety control switch is in the Off position. 1) To start the vehicle, press and release the transmitter button two times within 2 seconds. The vehicle will start and remain running for the pre-programmed run cycle. As a visual indication, the parking lights will lash or remain on depending on the setting by your installation center. 2) When you arrive at the vehicle, turn the ignition key to the ON position (not the spring loaded start position), then step on the brake pedal to disengage the remote starter. The vehicle will continue to run, but now on its own power. NOTE: The engine will stop running before the pre-programmed run cycle has expired if you perform any one of the following functions: -Press and the button on the keychain transmitter two times within 2 seconds -Depress the brake pedal -Open the vehicle's hood -Place the unit in the safety control disabled mode. PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL SWITCH The Push-Button LED switch located in the receiver allows you to temporarily disable the remote starting function of the system. This recommended whenever the vehicle is being serviced. To place the system in the service mode: 1) With the system disarmed/unlocked, and the ignition switch off, Press and Hold the Push-Button, found on the windsheild receiver, in. 2) Turn the ignition switch on, off, on, off, on, off. 3) The LED begins to lash two short lashes followed by one long lashes and continues this pattern until returned to normal mode of operation. This puts the unit into the R/S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise. To Exit R/S Override Mode 1) With the system disarmed, Press and Hold the Push-Button, found on the windsheild receiver, in. 2) Turn the ignition switch on, off, on, off, on, off. 3) The LED turns off indicating that the R/S unit is fully functional once again. 128-9297 2 of 4 UNLOCKING THE VEHICLE: If you have electric door lock, and the Optional Unlock feature was added, with the vehicle running under command of the remote start unit, press and hold the transmitter button for 3 seconds until the doors unlock. CAR FINDER MODE: Anytime the vehicle is not running under control of the remote start unit, within operating range of the vehicle, press and hold the push-button of the hand held transmitter for 4 seconds to activate the car inder mode. The vehicle lights will lash for 30 seconds or until the push-button is again pressed and released. TELEMATIC UPGRADE: This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that can give you control of certain functions of your vehicle from a Telephone, or in some cases a computer interface. Please check with your installation center for most recent Telematic Upgrades. If you had a Telematic Upgrade installed, the manual supplied with the upgrade unit will provide an operator's manual advising of the features of the system and means available to control these features of your vehicle. PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1) Transmitter Model Name, 141BPR Is Also Found On Back Of Transmitter Case. Use Battery CR2032 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times (Siren Chirps). 3) Press the Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4) Turn the ignition switch off. The above action programs the Start button for the one button start systems. Note: Some systems will not have a audible sound associated with programming,,,for these systems the lights will lash. 128-9297 3 of 4 Transmitter Battery Replacement 1) Locate and remove the "00" point philips head screw on the back of the transmitter case. 2) Carefully separate the front case from the rear. 3) Slide the CR2032 battery out from under the battery clip and dispose of properly. 4) Install the new battery with the (+) side facing up away from the circuit board. 5) Close the case and reassemble in reverse of disassembly FUNCTION SETTING CHART To be completed by installer Run Time 5 Min While Running Unlock Yes 10 Min No 15 Min Lights Pulse Steady 20 Min 45 Min 60 Min FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modiications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment NOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorized modiications to this equipment. Such modiications could void the user’s authority to operate the equipment To purchase replacement transmitters or to get additional product information go to: www.pursuitcarsecurity.com © 2014 Voxx Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-9297 128-9297 4 of 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print Create Date : 2014:06:30 09:03:08-04:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2014:07:29 17:33:45+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2014:07:29 17:33:45+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:cb6bba62-27f4-43ad-99ae-752aebd3982d Original Document ID : xmp.did:85BD9DC1CFAAE3118EA3D41E50F1DB8C Document ID : xmp.id:E64C28AE5600E41182138296A713C4DC Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:E31E8CDE5200E41182138296A713C4DC Derived From Document ID : xmp.did:DF1E8CDE5200E41182138296A713C4DC Derived From Original Document ID: xmp.did:85BD9DC1CFAAE3118EA3D41E50F1DB8C Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:06:30 09:03:08-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 4EXIF Metadata provided by EXIF.tools