OPISYS orporated AVHR-5000N InVehicle Dual Band Booster User Manual Manual rev 2

OPISYS Incorporated InVehicle Dual Band Booster Manual rev 2

UserManual.wiki >

OPISYS orporated >

AVHR 5000N User Manual HTML Version

Manual - rev 2

AVHR-5000N

- Content -

1. Precautions

2. System Components

2.1 Components

2.2 Installation

3. General Information

3.1 Features

4. Installation

4.1 External Antenna Installation

4.2 Inside Antenna Installation

4.3 Amplifier and Antenna Connection

4.4 Operating Instructions

5. Trouble Shooting

5.1 LED Alarm

5.2 Insufficient Outside Signal Problem

5.3 Vehicle Battery Discharge Problem

6. Safeguard features

6.1 Summary

6.2 Features

7. Specification

7.1 Amplifier Specification

7.2 Outside Antenna Specification

7.3 Inside Antenna Specification

7.4 Cigarette Power Code Specification

8. Certificates

9. Manufacturers

10. Memo

AVHR-5000N

1. Precautions

1.1 Do not drop the device

- It may damage the product and its function

1.2 Do not place near magnetic materials

- It may cause of possible malfunction

1.3 Product is recommended to be used with the cigarette power cord.

For any alternative cable use, please ask professional installers.

- There is a high risk of frying up the device if inaccurately powered.

1.4 Please unplug both Cigarette Power Supply and Fuse Cable during

non-operation to avoid any possible battery discharge.

1.5 Install the product where it is recommended

- It may not properly operate on unadvised location

1.6 Do not repair or remodel

- It may cause malfunction. Please contact your store representative

if there is a problem

Reference : Direction/Information for the proper operation

Caution : Information for users to avoid malfunctions

Warning : Instructions for users to avoid unexpected hazard

This is a CONSUMER device.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless

provider and have your provider’s consent. Most wireless providers consent

to the use of signal boosters. Some providers may not consent to the use of

this device on their network. If you are unsure, contact your provider.

You MUST operate this device with approved antennas and cables as

specified by the manufacturer. Antennas MUST be installed at least 20cm (8

inches) from any person. You MUST cease operating this device immediately

if requested by the FCC or a licensed wireless service provider. WARNING.

E911 location information may not be provided or may be inaccurate for calls

served by using this device.

This is a CONSUMER device.

AVHR-5000N

1.7 Do not install device while driving

- Please avoid any activities that may cause careless driving

1.8 Turn off the ignition before set up the device.

1.9 Do not install the device near any air bags in a car

- It may cause severe damage if air bags explode.

1.10 Do not touch the device with wet hands

- It may cause possible risk of an electric shock

1.11 Keep the installation location of inside and outside antenna clean

- Please organize cable lines and antenna locations to avoid any

possible interference while operating a vehicle.

1.12 Stop and Turn Off the device immediately if a smog comes out of

the product or any strange odor is detected from the product

- Do not attempt to fix the device. Please contact your store

representative

1.13 Warning message for use of unauthorized antennas, cables,

and/or coupling devices

- It may not properly operate

AVHR-5000N

① . Inside Antenna: connects signal between mobile phone and amplifier

②. Dual Band Amplifier: amplifies signal by receiving base station signals

through Outdoor antenna to In-door Antenna

③. User Manual: shows how to operate system

④. Cigarette Power Adapter: Power Source

⑤. Outside Antenna: connects signal between base station and amplifier

⑥. List of approved antennas

⑦. List the default antenna, cable, and/or coupling device that are shipped

with the booster

2. System Components

2.1 Components

Note: (A) Mark  Purchase separately

⑤ Outside Antenna

① Inside Antenna ② Dual Band Amplifier ③ User Manual

④

Cigarette power adapter

(A)

Inside Antenna TQC-900/1800E TS210380

Outside Antenna TQC-900/1800CII TS210580

Base Station

①

②

⑤

④

2.2 Installation

AVHR-5000N

3.1.1 Summary

The device may be installed on cars, trucks, trailers, boats and homes to

improve user’s mobile phone signal.

(Please see page 13 for Operating Frequency)

3.1.2 Features

I. Decrease dropped call

II. Increase 2G/3G data speed

III. Battery life extension

IV. Voice quality improvement

I. Strong coverage area

- Gain 48dB

II. Automatic Overload Protection & Detection System

- Plug and Operate Systems

III. 23dBm(0.2W) Output power

- Provides High Data Communication rate

IV. Complete Repeater Kit.

- All components included for installation

V. Dual Band Frequency Broadband

- 800MHz / 1900MHz

VI. LED Alarm System

VII. GUI(Graphic User Interface)

- Please ask professional installers about GUI program.

VIII. Cost Effective Application for Vehicles, Boats, and Homes

- For any Home & Boats applications, optional antennas

(inside & out) and connectors may be required.

3. General Information

3.1 Features

AVHR-5000N

4. Installation

4.1 External Antenna Installation

4.1.1 Outside antenna has magnetic feature to mount on the roof of vehicle

4.1.2 Outside antenna distance should be at least 5 feet from inside antenna

4.1.3 Recommended to mount outside antenna near rear end of the roof.

Good Better Best

4.2 Inside Antenna Installation

4.2.1Inside antenna is mounted using the self-adhesive. It must be placed in a location

that will be at least 0.5m (20 inches) from where cell phones will be located.

4.2.2 Before installation, please remove attached paper

4.2.3 Recommended to mount indoor antenna near suggested area as below

AVHR-5000N

4.3 Amplifier and Antenna Connection

4.3.1 Place the amplifier under the seat or appropriate location.

4.3.2 Connect inside and outside antenna connector to Amplifier.

4.4 Operating Instructions

4.4.1 Plug in cigarette power cord and press the button to turn ON as shown

below. The red LED light should be ON indicating its operation.

AVHR-5000N

4.4.2 Connect DC Jack as shown below

4.4.3 Turn ON the Switch as shown below

4.4.4 After turning ON the switch, green LED light will be on.

Green LED indicates that system is in a normal mode.

Green and Red LED will flash 3 times simultaneously.

After the initial loading, the green LED light will be on during operation.

AVHR-5000N

5. Trouble Shooting

5.1 LED Alarm

ITEM GREEN LED RED LED Problem Reference

Setting/Resetting ON

(after 3 times blinks) 3 times blinks See 4.1.1

Normal Mode ON OFF See 4.1.2

Cellular

Overload Blink( once) - See 4.1.3

Oscillation Blink(twice) - See 4.1.4

Insufficient

Isolation Blink(3 times) - See 4.1.5

Alarm Checking Blink(Consecutively) - See 4.1.6

Sleep Mode Blink(4 times) - See 4.1.7

PCS

Overload - Blink( once) See 4.1.3

Oscillation - Blink(twice) See 4.1.4

Insufficient

Isolation - Blink(3 times) See 4.1.5

Alarm Checking - Blink(Consecutively) See 4.1.6

Sleep Mode - Blink(4 times) See 4.1.7

5.1.1 ① Check if the LED light is ON, on the cigarette power adapter

② Verify that DC cord is connected correctly

5.1.2 ② Green LED light is normal mode. If it blinks 2-4 times in a few

seconds, please see 4.1.3 ~ 4.1.7

5.1.3 ② This is normal mode that checking on input power signal and shows

signal status to users.

② It will go resume normal operation mode after Overload Detection.

5.1.4 ② There is an oscillation between inside and outside antenna.

② This status is caused by surrounding structural interferences that

can temporarily disturb mobile signals. The amplifier will auto detect

available signals as you drive to other locations.

The Green LED light will turn ON once normal mode resumes.

5.1.5 ② The isolation may occur between inside and outside antenna

② If LED light blinks three times during installation, move the inside and

outside antenna away from each other and RESTART the amplifier.

② If LED light blinks three times after the installation, it could be caused

by surrounding structure.

The device will auto adjust as vehicle moves.

AVHR-5000N

5.2 Insufficient Outside Signal Problem

Even after installation, if there is no base stations around your

vehicle (Ex. No Service Enabled Zone), you may not receive any cellular

signals.

5.1.6 ① The Overload Protection System includes the following:

AGC (Automatic Gain Level Control)

AIC (Automatic Isolation Detection)

ASC (Automatic Reset Control)

② During Alarm checking process, the Amplifier may not operate.

5.1.7 ② When LED is green or red with a flash four times at working,

Sleep Mode is operated. Because reverse signal has not been existed

for a certain time.

② If Reverse signal occur at the Sleep Mode, repeater is working normally

and LED does not flash.

5.3 Vehicle Battery Discharge Problem

Verify cigarette power adapter has LED light ON as shown below. If not, check

either vehicle key is appropriately positioned or engine is ON. In case of

battery discharge, replace the battery.

AVHR-5000N

I. Isolation check mechanism

II. Oscillation check mechanism

III. Sleep Mode mechanism

IV. ALC(Auto Level Control) mechanism

V. RF Shut Down mechanism

6. Safeguard features

6.1 Summary

This equipment have functions to protect as follows.

6.2 Feature

6.2.1 Isolation check mechanism

- The booster automatically checks the isolation by increasing the

DL path gain by 1dB when the power supply is switched on and/or

the oscillation occurs.

It works normally when the isolation is over the maximum gain(48dB)

plus 10dB, 58dB.

6.2.2 Oscillation check mechanism

- Anti-oscillation function is to protect Booster by D/L path off

when oscillation in service. D/L shutdown by isolation check function

when D/L path output power exceed oscillation limit value.

6.2.3 Sleep Mode mechanism

- When there is no U/L path Input signal, Booster shall be shut down

after 30 seconds.

Under the Sleep Mode condition, if U/L path input signal is above

-92dBm, U/L path shall be turned on.

6.2.4 ALC(Auto Level Control) mechanism

- ALC function is always working to protect Booster.

6.2.5 RF Shut Down mechanism

- AMP is automatically shut down when the system output power

exceeds the set point over five seconds.

AVHR-5000N

7. Specification

7.1 Amplifier Specification

Items Cellular PCS Remarks

Operating Frequency Downlink 869 ~ 894 MHz 1930 ~ 1990 MHz

Uplink 824 ~ 849 MHz 1850 ~ 1910 MHz

Gain Downlink 48dB±2.0dB 48dB±2.0dB

Uplink 48dB±2.0dB 48dB±2.0dB

Output Power Level Downlink +5dBm +5dBm @ 1FA

Uplink +23dBm +23dBm

Ripple Downlink < 5dB < 5dB

Uplink < 5dB < 5dB

Noise Figure Downlink < 5dB < 5dB Frequency Center

Uplink < 5dB < 5dB Frequency Center

ALC Level Downlink +5dBm ±1dB +5dBm ±1dB @ 1FA

Uplink +23dBm ±1dB +23dBm ±1dB

Shutdown Level Downlink +6dBm ±1dB +6dBm ±1dB After ALC

Uplink +24dBm ±1dB +24dBm ±1dB

Modulation Type GSM. EDGE, CDMA, EVDO, WCDMA, LTE

Input Voltage 6.0Vdc / 3.5A Cigar Charger ‘s Vdc

Power Consumption 6.0Vdc / 1050mA @ No call

RF Connector Type FME-male

Operating Temperature -40°C ~ +50°C (-40°F ~ 122°F)

Size(L*W*H) 5.5”*4.8”* 1.3” (140.5 * 123 * 34 mm)

● Additional Information:

The EUT is a bi-directional amplifier for the boosting of cellular phone signals

and data communication devices.

The following frequency bands and emission types are utilized.

Frequency Band

Uplink 824~849 1850~1910

Downlink 869~894 1930~1990

Emission Designators

CDMA HSPA LTE EVDO EDGE GSM

F9W F9W G7D F9W G7W GXW

● EUT Operation during Tests

The EUT was in a normal operating condition.

AVHR-5000N

7.2 Outside Antenna Specification

Items Frequency Range Remarks

Operating Frequency 890 ~ 960 MHz

1710 ~ 1990 MHz -

Gain 5dBi -

VSWR ≤ 2.0 : 1 -

Impedance 50 Ω -

Max Power-W 50W

Polarization Vertical -

Connector FME(Female) -

Antenna Length 11.02 inch (28Cm) -

Items Frequency Range Remarks

Operating Frequency

700 ~ 800 MHz

824 ~ 894 MHz

880 ~ 960 MHz

1710 ~ 1880 MHz

1850 ~ 1990 MHz

2110 ~ 2170 MHz

Gain 5dBi -

VSWR ≤ 2.0 : 1 -

Impedance 50 Ω -

Max Power-W 50W

Polarization Vertical -

Connector FME(Female) -

Antenna Length 12.25 inch (31Cm) -

● TQC-900/1800CII

● TS210580

AVHR-5000N

7.3 Inside Antenna Specification

Items Frequency Range Remarks

Operating Frequency 820 ~ 890 MHz

1710 ~ 1990 MHz -

Gain 2dBi -

VSWR < 2.1 : 1 -

Impedance 50 Ω -

Max Power-W 25W

Polarization Vertical or Horizontal -

Connector FME(Female) -

Antenna Length 4.73 inch (12cm) -

Items Frequency Range Remarks

Operating Frequency 700 ~ 800 / 824~ 894 MHz

880~960 / 1850 ~ 1990 MHz -

Gain 3dBi -

VSWR < 1.8 : 1 -

Impedance 50 Ω -

Max Power-W 25W

Polarization 360º -

Connector FME(Female) -

Antenna Length 3.4 inch (8cm) -

● TQC-900/1800E

● TS210380

AVHR-5000N

7.4.2 Output Specification

Items Min Typical Max

Normal DC Output Voltage - 6.0Vdc -

DC Output Voltage Range 5.7Vdc - 6.3Vdc

Load Current Range - - 3.5A

Ripple - - 350mV

Over Current Protection 4.2 - 7.0A

Short Circuit Protection - Yes -

7.4 Cigarette Power Code Specification

7.4.1 Input Specification

Items Min Typical Max

Normal DC Input Voltage 12V - 24V

DC Input Voltage Range 12V - 24V

DC Input Voltage Current - - 3.0A

8. Certificates

8.1 FCC Certification

Model : AVHR-5000N

▪ Certificate Data : April 18, 2014

▪ Certificate Number: Q4EAVHR-5000N

9. Manufacturers

9.1 Location

▪ Address : 590 West Central Ave Unit E, Brea CA 92821

▪ Tel : 714-990-6244

▪ Fax : 714-990-6243

AVHR-5000N

Memo

OPISYS orporated AVHR-5000N InVehicle Dual Band Booster User Manual Manual rev 2

OPISYS Incorporated InVehicle Dual Band Booster Manual rev 2

Manual - rev 2

Navigation menu

Namespaces

Views

Navigation