OPISYS orporated AVHR-5000N InVehicle Dual Band Booster User Manual Manual rev 2
OPISYS Incorporated InVehicle Dual Band Booster Manual rev 2
Manual - rev 2
- Content - All rights reserved AVHR-5000N 1. Precautions 2. System Components 2.1 Components 2.2 Installation 3. General Information 3.1 Features 4. Installation 4.1 External Antenna Installation 4.2 Inside Antenna Installation 4.3 Amplifier and Antenna Connection 4.4 Operating Instructions 5. Trouble Shooting 5.1 LED Alarm 5.2 Insufficient Outside Signal Problem 5.3 Vehicle Battery Discharge Problem 6. Safeguard features 6.1 Summary 6.2 Features 7. Specification 7.1 Amplifier Specification 7.2 Outside Antenna Specification 7.3 Inside Antenna Specification 7.4 Cigarette Power Code Specification 8. Certificates 9. Manufacturers 10. Memo 1. Precautions This is a CONSUMER device. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. Reference : Direction/Information for the proper operation Caution : Information for users to avoid malfunctions Warning : Instructions for users to avoid unexpected hazard All rights reserved AVHR-5000N 1.1 Do not drop the device - It may damage the product and its function 1.2 Do not place near magnetic materials - It may cause of possible malfunction 1.3 Product is recommended to be used with the cigarette power cord. For any alternative cable use, please ask professional installers. - There is a high risk of frying up the device if inaccurately powered. 1.4 Please unplug both Cigarette Power Supply and Fuse Cable during non-operation to avoid any possible battery discharge. 1.5 Install the product where it is recommended - It may not properly operate on unadvised location 1.6 Do not repair or remodel - It may cause malfunction. Please contact your store representative if there is a problem 1.7 Do not install device while driving - Please avoid any activities that may cause careless driving 1.8 Turn off the ignition before set up the device. 1.9 Do not install the device near any air bags in a car - It may cause severe damage if air bags explode. 1.10 Do not touch the device with wet hands - It may cause possible risk of an electric shock 1.11 Keep the installation location of inside and outside antenna clean - Please organize cable lines and antenna locations to avoid any possible interference while operating a vehicle. 1.12 Stop and Turn Off the device immediately if a smog comes out of the product or any strange odor is detected from the product - Do not attempt to fix the device. Please contact your store representative 1.13 Warning message for use of unauthorized antennas, cables, and/or coupling devices - It may not properly operate AVHR-5000N All rights reserved 2. System Components 2.1 Components (A) ① Inside Antenna ② Dual Band Amplifier ③ User Manual (A) ⑤ Outside Antenna ④ Cigarette power adapter Note: (A) Mark Purchase separately ① . Inside Antenna: connects signal between mobile phone and amplifier ②. Dual Band Amplifier: amplifies signal by receiving base station signals through Outdoor antenna to In-door Antenna ③. User Manual: shows how to operate system ④. Cigarette Power Adapter: Power Source ⑤. Outside Antenna: connects signal between base station and amplifier ⑥. List of approved antennas Inside Antenna TQC-900/1800E TS210380 Outside Antenna TQC-900/1800CII TS210580 ⑦. List the default antenna, cable, and/or coupling device that are shipped with the booster 2.2 Installation ⑤ ④ ① ② All rights reserved AVHR-5000N Base Station 3. General Information 3.1 Features 3.1.1 Summary The device may be installed on cars, trucks, trailers, boats and homes to improve user’s mobile phone signal. I. II. III. IV. Decrease dropped call Increase 2G/3G data speed Battery life extension Voice quality improvement (Please see page 13 for Operating Frequency) 3.1.2 Features I. All rights reserved AVHR-5000N Strong coverage area - Gain 48dB II. Automatic Overload Protection & Detection System - Plug and Operate Systems III. 23dBm(0.2W) Output power - Provides High Data Communication rate IV. Complete Repeater Kit. - All components included for installation V. Dual Band Frequency Broadband - 800MHz / 1900MHz VI. LED Alarm System VII. GUI(Graphic User Interface) - Please ask professional installers about GUI program. VIII. Cost Effective Application for Vehicles, Boats, and Homes - For any Home & Boats applications, optional antennas (inside & out) and connectors may be required. 4. Installation 4.1 External Antenna Installation 4.1.1 Outside antenna has magnetic feature to mount on the roof of vehicle 4.1.2 Outside antenna distance should be at least 5 feet from inside antenna 4.1.3 Recommended to mount outside antenna near rear end of the roof. Good Better Best 4.2 Inside Antenna Installation 4.2.1Inside antenna is mounted using the self-adhesive. It must be placed in a location that will be at least 0.5m (20 inches) from where cell phones will be located. 4.2.2 Before installation, please remove attached paper 4.2.3 Recommended to mount indoor antenna near suggested area as below AVHR-5000N All rights reserved 4.3 Amplifier and Antenna Connection 4.3.1 Place the amplifier under the seat or appropriate location. 4.3.2 Connect inside and outside antenna connector to Amplifier. 4.4 Operating Instructions 4.4.1 Plug in cigarette power cord and press the button to turn ON as shown below. The red LED light should be ON indicating its operation. AVHR-5000N All rights reserved 4.4.2 Connect DC Jack as shown below 4.4.3 Turn ON the Switch as shown below 4.4.4 After turning ON the switch, green LED light will be on. Green LED indicates that system is in a normal mode. Green and Red LED will flash 3 times simultaneously. After the initial loading, the green LED light will be on during operation. AVHR-5000N All rights reserved 5. Trouble Shooting 5.1 LED Alarm ITEM GREEN LED RED LED Problem Reference 3 times blinks See 4.1.1 ON OFF See 4.1.2 Overload Blink( once) See 4.1.3 Oscillation Blink(twice) See 4.1.4 Insufficient Isolation Blink(3 times) See 4.1.5 Alarm Checking Blink(Consecutively) See 4.1.6 Sleep Mode Blink(4 times) See 4.1.7 Overload Blink( once) See 4.1.3 Oscillation Blink(twice) See 4.1.4 Insufficient Isolation Blink(3 times) See 4.1.5 Alarm Checking Blink(Consecutively) See 4.1.6 Sleep Mode Blink(4 times) See 4.1.7 ON Setting/Resetting (after 3 times blinks) Normal Mode Cellular PCS 5.1.1 ① Check if the LED light is ON, on the cigarette power adapter ② Verify that DC cord is connected correctly 5.1.2 ① Green LED light is normal mode. If it blinks 2-4 times in a few seconds, please see 4.1.3 ~ 4.1.7 5.1.3 ① This is normal mode that checking on input power signal and shows signal status to users. ② It will go resume normal operation mode after Overload Detection. 5.1.4 ① There is an oscillation between inside and outside antenna. ② This status is caused by surrounding structural interferences that can temporarily disturb mobile signals. The amplifier will auto detect available signals as you drive to other locations. The Green LED light will turn ON once normal mode resumes. All rights reserved AVHR-5000N 5.1.5 ① The isolation may occur between inside and outside antenna ② If LED light blinks three times during installation, move the inside and outside antenna away from each other and RESTART the amplifier. ③ If LED light blinks three times after the installation, it could be caused by surrounding structure. The device will auto adjust as vehicle moves. 10 5.1.6 ① The Overload Protection System includes the following: AGC (Automatic Gain Level Control) AIC (Automatic Isolation Detection) ASC (Automatic Reset Control) ② During Alarm checking process, the Amplifier may not operate. 5.1.7 ① When LED is green or red with a flash four times at working, Sleep Mode is operated. Because reverse signal has not been existed for a certain time. ② If Reverse signal occur at the Sleep Mode, repeater is working normally and LED does not flash. 5.2 Insufficient Outside Signal Problem Even after installation, if there is no base stations around your vehicle (Ex. No Service Enabled Zone), you may not receive any cellular signals. 5.3 Vehicle Battery Discharge Problem Verify cigarette power adapter has LED light ON as shown below. If not, check either vehicle key is appropriately positioned or engine is ON. In case of battery discharge, replace the battery. AVHR-5000N All rights reserved 11 6. Safeguard features 6.1 Summary This equipment have functions to protect as follows. I. II. III. IV. V. Isolation check mechanism Oscillation check mechanism Sleep Mode mechanism ALC(Auto Level Control) mechanism RF Shut Down mechanism 6.2 Feature 6.2.1 Isolation check mechanism - The booster automatically checks the isolation by increasing the DL path gain by 1dB when the power supply is switched on and/or the oscillation occurs. It works normally when the isolation is over the maximum gain(48dB) plus 10dB, 58dB. 6.2.2 Oscillation check mechanism - Anti-oscillation function is to protect Booster by D/L path off when oscillation in service. D/L shutdown by isolation check function when D/L path output power exceed oscillation limit value. 6.2.3 Sleep Mode mechanism - When there is no U/L path Input signal, Booster shall be shut down after 30 seconds. Under the Sleep Mode condition, if U/L path input signal is above -92dBm, U/L path shall be turned on. 6.2.4 ALC(Auto Level Control) mechanism - ALC function is always working to protect Booster. 6.2.5 RF Shut Down mechanism - AMP is automatically shut down when the system output power exceeds the set point over five seconds. AVHR-5000N All rights reserved 12 7. Specification 7.1 Amplifier Specification Items Cellular PCS Remarks Downlink 869 ~ 894 MHz 1930 ~ 1990 MHz Uplink 824 ~ 849 MHz 1850 ~ 1910 MHz Downlink 48dB±2.0dB 48dB±2.0dB Uplink 48dB±2.0dB 48dB±2.0dB Downlink +5dBm +5dBm Uplink +23dBm +23dBm Downlink < 5dB < 5dB Uplink < 5dB < 5dB Downlink < 5dB < 5dB Frequency Center Uplink < 5dB < 5dB Frequency Center Downlink +5dBm ±1dB +5dBm ±1dB Uplink +23dBm ±1dB +23dBm ±1dB Downlink +6dBm ±1dB +6dBm ±1dB Uplink +24dBm ±1dB +24dBm ±1dB Operating Frequency Gain Output Power Level @ 1FA Ripple Noise Figure ALC Level @ 1FA Shutdown Level After ALC Modulation Type GSM. EDGE, CDMA, EVDO, WCDMA, LTE Input Voltage 6.0Vdc / 3.5A Cigar Charger ‘s Vdc Power Consumption 6.0Vdc / 1050mA @ No call RF Connector Type FME-male Operating Temperature -40°C ~ +50°C (-40°F ~ 122°F) Size(L*W*H) 5.5”*4.8”* 1.3” (140.5 * 123 * 34 mm) ● Additional Information: The EUT is a bi-directional amplifier for the boosting of cellular phone signals and data communication devices. The following frequency bands and emission types are utilized. Frequency Band Uplink 824~849 1850~1910 Downlink 869~894 1930~1990 CDMA HSPA LTE EVDO EDGE GSM F9W F9W G7D F9W G7W GXW ● EUT Operation during Tests The EUT was in a normal operating condition. All rights reserved AVHR-5000N Emission Designators 13 7.2 Outside Antenna Specification ● TQC-900/1800CII Items Frequency Range Remarks 890 ~ 960 MHz Operating Frequency 1710 ~ 1990 MHz Gain 5dBi VSWR ≤ 2.0 : 1 Impedance 50 Ω Max Power-W 50W Polarization Vertical Connector FME(Female) Antenna Length 11.02 inch (28Cm) Frequency Range Remarks ● TS210580 Items 700 ~ 800 MHz 824 ~ 894 MHz 880 ~ 960 MHz Operating Frequency 1710 ~ 1880 MHz 1850 ~ 1990 MHz 2110 ~ 2170 MHz 5dBi VSWR ≤ 2.0 : 1 Impedance 50 Ω Max Power-W 50W Polarization Vertical Connector FME(Female) Antenna Length 12.25 inch (31Cm) AVHR-5000N All rights reserved Gain 14 7.3 Inside Antenna Specification ● TQC-900/1800E Items Frequency Range Remarks 820 ~ 890 MHz Operating Frequency 1710 ~ 1990 MHz Gain 2dBi VSWR < 2.1 : 1 Impedance 50 Ω Max Power-W 25W Polarization Vertical or Horizontal Connector FME(Female) Antenna Length 4.73 inch (12cm) Frequency Range Remarks ● TS210380 Items 700 ~ 800 / 824~ 894 MHz Operating Frequency 880~960 / 1850 ~ 1990 MHz 3dBi VSWR < 1.8 : 1 Impedance 50 Ω Max Power-W 25W Polarization 360º Connector FME(Female) Antenna Length 3.4 inch (8cm) AVHR-5000N All rights reserved Gain 15 7.4 Cigarette Power Code Specification 7.4.1 Input Specification Items Min Typical Max Normal DC Input Voltage 12V 24V DC Input Voltage Range 12V 24V DC Input Voltage Current 3.0A 7.4.2 Output Specification Items Min Typical Max Normal DC Output Voltage 6.0Vdc DC Output Voltage Range 5.7Vdc 6.3Vdc Load Current Range 3.5A Ripple 350mV Over Current Protection 4.2 7.0A Short Circuit Protection Yes 8. Certificates 8.1 FCC Certification Model : AVHR-5000N ▪ Certificate Data : April 18, 2014 ▪ Certificate Number: Q4EAVHR-5000N 9. Manufacturers 9.1 Location All rights reserved AVHR-5000N ▪ Address : 590 West Central Ave Unit E, Brea CA 92821 ▪ Tel : 714-990-6244 ▪ Fax : 714-990-6243 16 Memo AVHR-5000N All rights reserved 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : admin Create Date : 2014:10:10 10:29:38+09:00 Modify Date : 2014:10:10 10:29:46+09:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2014:10:10 10:29:46+09:00 Creator Tool : PowerPoint용 Acrobat PDFMaker 10.1 Document ID : uuid:bba0bb05-ced4-49ba-8700-4565697a03e2 Instance ID : uuid:727a09eb-ef81-48cb-a30f-5c4cbe96803c Format : application/pdf Title : PowerPoint 프레젠테이션 Creator : admin Producer : Adobe PDF Library 10.0 Company : Hewlett-Packard Page Layout : SinglePage Page Count : 17EXIF Metadata provided by EXIF.tools