OPISYS orporated USHR-700L In-Building Repeater System User Manual Revised
OPISYS Incorporated In-Building Repeater System Users Manual Revised
Users Manual Revised
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2446934 |
| Application ID | 1n0OMWihhEZkPoav2Y2DQg== |
| Document Description | Users Manual Revised |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 65.84kB (822947 bits) |
| Date Submitted | 2014-11-17 00:00:00 |
| Date Available | 2015-01-03 00:00:00 |
| Creation Date | 2014-11-14 16:41:35 |
| Producing Software | Adobe PDF Library 10.0 |
| Document Lastmod | 2014-11-14 18:11:08 |
| Document Title | EZ CELL 사용설명서 (MODEL : AEHR-2009) |
| Document Creator | PowerPointìš© Acrobat PDFMaker 10.1 |
| Document Author: | ì•„ì´ì†” |
Users Guide Installation Manual USHR-700L - Content 1. General Information 2. System Components 3. Installation 4. Trouble Shooting 5. Specification 6. Certificates 7. Memo This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. Page 2 1. General Information 1.1. Precautions Reference : Direction/Information for the proper operation Cautions : Information for users to avoid malfunctions Warning : Instruction for users to avoid unexpected hazard 1.1.1 Do not drop the device - It may damage the product and its function 1.1.2 Do not place near magnetic material - It may cause of possible malfunction 1.1.3 Product is recommended to be used with original AC/DC adapter 1.1.4 Install the product where it is recommended - It may not properly operate if it is not recommended location 1.1.5 Do not disassemble/ repair the product - Warranty may void once you disassemble the product. 1.1.6 Turn off the device immediately if a smog or any strange odor is detected from the product. 1.1.7 Use contained bolt to install on the wall. Make sure it is safely installed before operation Page 3 1.2 . Features 1.2.1. Summary This device may be installed on residential area, office, warehouse etc. . Following is advantage of using in-building repeater system. I. Decrease dropped call rate II. Increase signal strength III. Improve Data / Voice quality IV. Prolong hand phone battery life V. Improve data Communication Rate This is RF type amplifier for 700 MHz LTE of Band 12 and Band 13 signal enhancement. (Please see page 13 for Operating Frequency in details) 1.2.2 . Features I. Wider Coverage area - Band 12 Gain DL 61dB /UL 60dB, Band 13 Gain DL 61dB/ UL 60dB. II. ALC(Automatic output Level Control) - Stabilize operation in any radio environment III. Fulfill 3GPP spurious specification at +22dBm output power (category A) - Provide high Data Communication Rate IV. Easy gain control by dip switch located on the front side of product V. Support dual band - enable to connect service from multiple currier simultaneously - LTE Band 12/13 service simultaneously - LTE Band 12/13 adopt independent operation algorithm VI. Check status of product by LED indicator VII. Manage and control product by GUI(Graphic User Interface) - Please ask professional installer about GUI Program VIII. Enable to stay connected in homes and offices - Please ask professional installer for installation on homes & offices IX. X. LTE ready Automatically isolation detection and gain setting - Power ON/OFF when oscillation occurs. XI. UP Link Sleep Mode - If no signal detected for 5 minutes, UP Link Path Shuts Off XII. UL/DL gain Interlocking Mode Page 4 1.2.3. Function I. S/D ( Auto Shut Down Mode) Built-In Automatic Self-Monitoring Features for Anti-Oscillation: Automatic Shut Down Mode operates when oscillation in the uplink and downlinks bands are detected, thus terminates potential harmful interference to wireless networks. • 1 MINUTE Non-Operative Mode on the first initial oscillation detection. • Default Algorithm Re-Set Mode when Auto S/D Mode is cleared • Complete Shut Off Mode on the 5th repetition of Auto S/D Mode status. BAND 12 & BAND 13 PATH are independently monitored and operated. II. Intermodulation Gain & Power Limit Control Uplink & Downlink PATH formulate consistent link balance to regulate its input and output gain & power limits. max UL gain < - 34dB – RSSI + MSCL (“ FCC 13-21,(i), 78p”) RSSI : the downlink composite received signal power at the donor port ( calculation value : DL Output – DL Gain ) MSCL : Mobile Station and repeater service port minimum Coupling Loss ( setting value ) BAND 12 & BAND 13 PATH gain limits are independently controlled III. ALC (Automatic Level Control) ALC is implemented due to the higher rate of signal changes and wide dynamic range in LTE Bands, the Automatic Gain Power Control (AGC) may experience off set time synchronization error. • Optimal Window Size (frequency range) sets the optimal level to increase faster response to LTE Frequency changes on the basis of gain power control via signal input/output differential calculation BAND 12 & BAND 13 PATH gain limits are independently controlled IV. UL PATH Automatic Sleep Mode If coverage is non-existent (Zero Area Zone), Uplink PATH shuts off as A Harmful Interference Avoidance protocol and minimizes its power consumption. Page 4 1.2.3. Function IV. UL PATH Automatic Sleep Mode (continue ) • Automatic Turn OFF / if UL PATH < -92dBm • Automatic Turn ON / if UL PATH > -90dBm **BAND 12 & BAND 13 PATH gain limits are independently controlled V. Oscillation Auto Prevention • Degradation Protection: Detects potential performance degradation due to the overload LTE feedback (over-heating) signals by Isolation Check & Gain Configuration. • Feedback Limits: Sets the operating range to exceeding high level Signals from Donor Antenna (external antenna) of a signal booster to Service Antenna (internal antenna) BDA Gain < Antenna to Antenna Isolation – 15dB If optimal isolation gain is not attained, PATH OFF shuts off automatically **BAND 12 & BAND 13 Uplink PATH are independently controlled Page 4 2. System components ② AC/DC Adapter ① Dual Band Repeater ④ Installation bolts ③ User Manual ① Dual band Repeater : BTS and mobile phone signal booster ② AC/DC Adaptor : 110VAC power supply ③ User Manual : Operation manual ④ Installation Bolts : Holds repeater on the vertical wall ● List of approved antennas & cables Antenna Item Service Antenna (Indoor Antenna) Donor Antenna (Outdoor Antenna) RF Cable Model Gain Model Cable type PAT-CPWI-L +4dBi AC200000 LMR200 TS260771 +8dBi TS320000 RF240 TS250374 +5dBi TS340000 RF400 ALP-17QD-L +6dBi TS350000 ½” TS210471 +4.5dBi TS360000 ½” TS220971 +9dBi Page 5 3. Installation Out Door Antenna 3.1. Installation diagram Indoor Antenna Donor Antenna Service Antenna BTS Base satation USHR-700L 3.1.1. Install Donor Antenna on higher location to avoid any signal interference. Mount towards to the BTS where a clear line-of-sight path exists for optimal signal level. 3.1.2. Install service antenna at appropriate location such as wall or roof ceiling. Make sure service antenna is not blocked by furniture or hope appliance. 3.1.3. Use enclosed bolt to fix repeater on the wall and plug in power adaptor. 3.1.4. For best optimal operation, antenna isolation (oscillation level) should be set above minimum 15 dB gain. The industry standard for antenna to antenna isolation formula is BDA gain + 15 dB. 3.2. Repeater Indoor ANT Port Band 12 Status LED POWER LED Outdoor ANT Port Band 13 Status LED GUI PORT Power ON/OFF Switch POWER Jack Port LTE Band12 Gain control Dip Switch LTE Band13 Gain control Dip Switch Page 6 3.3. Repeater and Antenna connection 3.3.1. Connect donor antenna cable to outdoor antenna port as shown below. 3.3.2. Connect Service antenna to indoor antenna port as shown below. 3.3.3. Plug in power adaptor to power outlet. Page 7 3.3.4. Plug in AD/DC adaptor to connector listed as DC5.6V 3.3.5. Once power is on, it will show 3 green LED light on the front of product as shown below. LTE Band12 Gain manual control Dip Switch (0~25dB) LTE Band13 Gain manual control Dip Switch (0~25dB) 3.3.6 The factory default set-up has both Automatic Attenuator Control (AAC) & Automatic Level Control (ALC) pre-activated by USHR-700L Internal CPU. All Isolation Check features can be manually adjusted via Dip switch using GUI program (Repeater Control & Monitoring Software). Page 8 4. Trouble Shooting 4.1. LED Status Item GREEN LED RED LED Reference ON × See 4.1.1 OFF × See 4.1.1 ON See 4.1.2 ON See 4.1.3 Green Blinking per 1 sec cycle See 4.1.4 Green Blinking per 5 sec cycle See 4.1.5 RED Blinking per 1 sec cycle See 4.1.6 RED Blinking per 5 sec cycle See 4.1.7 ON See 4.1.8 ON See 4.1.9 Green Blinking per 1 sec cycle See 4.1.10 Green Blinking per 5 sec cycle See 4.1.11 RED Blinking per 1 sec cycle See 4.1.12 RED Blinking per 5 sec cycle See 4.1.13 PWR LTE Band 12 LTE Band 13 4.1.1. Power on /off status. 4.1.1. Power on /off status. 4.1.2. Band 12 normal operation condition. 4.1.3. Band 12 detects excessive input signal and shut down. 4.1.4 Shut Down Algorithm status on BAND 12 Signal Input. 4.1.5. PATH OFF indicator during Uplink Sleep Mode for BAND 12. 4.1.6. Isolation SD Algorithm status on Band 12 4.1.7. Band 12 detects Insufficient Isolation between donor & service antenna and shut down. 4.1.8. Band 13 normal operation condition. 4.1.9. Band 13 detects excessive input signal and shut down. 4.1.10 Shut Down Algorithm status on BAND 13 Signal Input. 4.1.11. PATH OFF indicator during Uplink Sleep Mode for BAND 13. 4.1.12. PATH OFF indicator during Uplink Sleep Mode for BAND 12. 4.1.13. Band 12 detects Insufficient Isolation between donor & service antenna and shut down. Page 9 5. Specification 5.1. Electrical Specification Item Frequency Range Modulation Type Output Power Gain Noise Figure Noise Power Limit Down Link 728 ~ 746 MHz Up Link 698 ~ 716 MHz Down Link 746 ~ 757 MHz Up Link 776 ~ 787 MHz Up Link -13dBm max Down Link -45dBm max Up Link -13dBm max Down Link +2dBm @ booster output port LTE DL 5MHz 25RB Up Link +22dBm @ booster output port LTE UL 5MHz 25RB Down Link +2dBm @ booster output port LTE DL 5MHz 25RB Up Link +22dBm @ booster output port LTE UL 5MHz 25RB Down Link 47dB ~ 61dB (±1.0dB) Up Link 35dB ~ 60dB (±1.0dB) Uplink In-activity BAND12 47dB ~ 61dB (±1.0dB) 35dB ~ 60dB (±1.0dB) Down / Up Link < 4dB BAND12 Down / Up Link < 4dB BAND13 Down / Up Link < 6.0dB / < 6.0dB BAND12 Max Gain Down / Up Link < 6.0dB / < 6.0dB BAND13 Max Gain Down Link < -70dBm/MHz On shutdown Up Link < -70dBm/MHz On shutdown & sleep mode Down / Up Link FCC BAND12 FCC BAND13 ≤ 1.8 : 1 OSC Level BAND13 Up Link VSWR Shutdown Level BAND12 Down Link < 3us Uplink Gain limit BAND13 -45dBm max Down / Up Link ALC Range BAND12 Down Link Propagation Delay ALC Setting Level Note GSM. EDGE, CDMA, EVDO, HSPA, LTE Input Power limit Ripple Specifications Down Link(Upper Value) +2dBm±1.0dB Window Size(Lower Offset) 0 ~ 10dB Up Link (Upper Value) +22dBm±1.0dB Window Size(Lower Offset) 0 ~ 10dB Down Link ≤ 14dB Up Link ≤ 25dB DL starting input level for Uplink Gain Interlocking -68 dBm Down Link > -45dBm/Total Up Link > -13dBm/Total Down Link DL detects OSC under 1 sec. Up Link UL detects OSC under 0.3 sec. Up link On@ > -90dBm, OFF@ < -92dBm BAND13 - ALC, SD, OSC functional opera tion is completely separate BAN D12 and BAND13. - No uplink signal for 5 minutes Page 10 Down Link 0dB ~ 14dB / 1dB step @ Band12 Up Link 0dB ~ 25dB / 1dB step @ Band13 Down link 0dB ~ 25dB / 1dB Step Up link 0dB ~ 25dB / 1dB Step ALC Gain Control Range Dip Switch Gain Control Deviation < ± 1dB EVM < 7% Down Link - be controlled GUI or Dip Switch - Total Atten control Range : 0dB ~ 25dB / 1dB Step (Both DL and UL are the same) No Feedback ≥ 38dB LTE DL 5MHz 25RB ACLR (± 10MHz) Up Link ≥ 32dB LTE UL 5MHz 25RB 47dB ~ 75dB / BAND12 Isolation checking Range Detecting deviation: < ±2.0dB 47dB ~ 75dB / BAND13 In band Spurious (Operating band unwanted emissions) Category A 3GPP TS 36.106 < -13dBm/1kHz RBW 9kHz ~ 150kHz < -13dBm/10kHz RBW 150kHz ~ 30MHz < -13dBm/100kHz RBW 30MHz ~ 1GHz < -13dBm/1MHz RBW 1GHz ~ 12.75GHz Out Band Spurious 3rd IMD < -19dBm Frequency Stability ≤ ±0.01ppm GUI Interface RS-232C Power Consumption < 15 W Operating Power AC/DC Adapter(AC110V or AC220V) RF Connector N-type Female ● Additional Information: This repeater is a bi-directional amplifier for the boosting of cellular phone signals and data communication devices. The following frequency bands and emission types are utilized. Frequency Band Uplink 698 ~ 716 MHz 776 ~ 787 MHz Downlink 728 ~ 746 MHz 746 ~ 757 MHz Emission Designators CDMA HSPA LTE EVDO EDGE GSM F9W F9W G7D F9W G7W GXW Page 11 5.2. Mechanical Specification Item Specifications Dimensions (L × W × H) 151mm x 191mm x 35mm (5.95 x 7.5 x 1.38 inch) Weight < 2Kg Note 5.3. Environment Specification Item Specifications Temperature -30 ~ 55℃(-22 ~ 131℉) Humidity 10 ~ 95% Note 5.4. AC/DC Adaptor Specification Items Specifications AC input power 90VAC ~ 264VAC, 47Hz ~ 63Hz Output rated Voltage +5.5VDC/1.3A Voltage Current range 2.5A ~ 0.0 A Operation Temperature -30℃ ~ +55℃ Operation humidity 10% ~ 90% Note 6. Certificates 6.1 FCC Certification Model : USHR-700L ▪ Certificate Data : ▪ Certificate Number: Page 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Author : 아이솔 Create Date : 2014:11:14 16:41:35+09:00 Modify Date : 2014:11:14 18:11:08+09:00 Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2014:11:14 18:11:08+09:00 Creator Tool : PowerPoint용 Acrobat PDFMaker 10.1 Document ID : uuid:4485b420-9b2a-48f5-be57-605836357eb0 Instance ID : uuid:61dc52ef-2ea9-4cd6-9684-5ea2e180304a Format : application/pdf Title : EZ CELL 사용설명서 (MODEL : AEHR-2009) Creator : 아이솔 Producer : Adobe PDF Library 10.0 Company : 중계기팀 Page Layout : SinglePage Page Count : 14EXIF Metadata provided by EXIF.tools