OPTOELECTRONICS OPN3102I Data Collector User Manual
OPTOELECTRONICS Co., Ltd. Data Collector Users Manual
Users Manual
SPECIFIICATIONS MANUAL OPN OP N-331002i OPN-3102i 1st Data Colle ector with h Bluetootth This manual prov vides speciifications fo or the OPN N-3102i Bluuetooth data a collector with 2D im mager scan nner. 1st SPECIFICATIONS MANUAL OPN-3102i 1st The information in this document is subject to change without notice. Document History Model Number: Edition: Date: OPN-3102i 1st 30-September-2016 Specification Number: Original Spec Number: SS16057 (SS15053) 2016 Copyright Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase excluding batteries. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your data collector or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184 SUPPORT USA Europe Phone: 800-636-0090 Email: support@opticonusa.com Web: www.opticonusa.com Email: support@opticon.com Web: www.opticon.com SPECIFICATIONS MANUAL OPN-3102i 1st Revision History Product Name : OPN-3102i Edition st Date 2016/09/30 Page Section Description of Changes SPECIFICATIONS MANUAL OPN-3102i 1st Contents Abstract............................................................................................................................ 6 Overview .......................................................................................................................... 6 Basic Specifications ....................................................................................................... 7 Detailed View .................................................................................................................10 Electrical Specifications ............................................................................................... 11 5.1 USB ........................................................................................................................................ 11 5.2 Wireless Charging .................................................................................................................. 11 Interface Specifications ................................................................................................ 11 6.1 USB Interface ......................................................................................................................... 11 6.1.1 Connector ....................................................................................................................... 11 6.1.2 USB Interface Circuit ...................................................................................................... 11 6.2 Bluetooth ................................................................................................................................ 12 6.3 NFC Tag ................................................................................................................................. 12 Optical Specifications................................................................................................... 13 7.1 Basic Specifications ............................................................................................................... 13 7.2 Aiming Pattern ........................................................................................................................ 14 Technical Specifications .............................................................................................. 15 8.1 Barcode Test Sample ............................................................................................................. 16 8.2 Scan Area and Depth of Field ................................................................................................ 17 8.3 Printed Contrast Signal (PCS) ............................................................................................... 19 8.4 Minimum Resolution ............................................................................................................... 19 8.5 Barcode Width ........................................................................................................................ 19 8.6 Pitch, Skew and Tilt ................................................................................................................ 20 8.7 Curvature ................................................................................................................................ 20 8.8 Scanning from LCD Screen.................................................................................................... 21 8.9 Motion Tolerance.................................................................................................................... 21 Environmental Specifications ...................................................................................... 22 9.1 Temperature ........................................................................................................................... 22 9.2 Humidity.................................................................................................................................. 22 9.3 Ambient Light Immunity .......................................................................................................... 22 9.4 Dust and Drip Proof ................................................................................................................ 22 9.5 Vibration Strength (without packing) ...................................................................................... 23 9.6 Vibration Strength (in individual packing) ............................................................................... 23 9.7 Drop Impact Strength (without packaging) ............................................................................. 23 9.8 Drop Impact Strength (in individual packaging) ..................................................................... 23 9.9 Electrostatic Discharge Immunity ........................................................................................... 23 10 Regulatory Compliance ................................................................................................ 24 10.1 LED Safety ............................................................................................................................. 24 10.2 Product Safety ........................................................................................................................ 24 10.3 EMC........................................................................................................................................ 24 SPECIFICATIONS MANUAL 10.4 OPN-3102i 1st Other....................................................................................................................................... 25 11 RoHS .............................................................................................................................. 25 12 Reliability ....................................................................................................................... 25 13 Precautions.................................................................................................................... 25 13.1 Radio Law............................................................................................................................... 26 13.2 Bluetooth ................................................................................................................................ 26 13.3 Frequency Band ..................................................................................................................... 26 14 Product Labels .............................................................................................................. 27 15 Packaging Specifications ............................................................................................. 28 15.1 Individual Packaging .............................................................................................................. 28 15.2 Collective Packaging .............................................................................................................. 29 16 Physical Features.......................................................................................................... 30 16.1 Dimensions ............................................................................................................................. 30 16.2 Weight .................................................................................................................................... 30 16.3 Mechanical Drawing ............................................................................................................... 30 17 Supported Symbologies ............................................................................................... 31 17.1 Default Setting ........................................................................................................................ 31 17.2 Supported Symbologies ......................................................................................................... 31 17.2.1 1D Barcodes ................................................................................................................... 31 17.2.2 GS1 Databar, Composite Code ...................................................................................... 32 17.2.3 2D Codes ........................................................................................................................ 32 Table of Figures Figure 1: Detailed View ......................................................................................................................... 10 Figure 2: micro USB B Connector ......................................................................................................... 11 Figure 3: Interface Circuit (USB) ........................................................................................................... 11 Figure 4: Aiming Pattern and Imaging Range ....................................................................................... 14 Figure 5: Scanning conditions ............................................................................................................... 15 Figure 6: Scan Area and Depth of Field ................................................................................................ 18 Figure 7: Wide Barcode ......................................................................................................................... 19 Figure 8: Pitch, Skew and Tilt ................................................................................................................ 20 Figure 9: Curvature................................................................................................................................ 20 Figure 10: Motion Tolerance.................................................................................................................. 21 Figure 11: Drop Test.............................................................................................................................. 23 Figure 12: Product Label Position ......................................................................................................... 27 Figure 13: Individual Packaging ............................................................................................................ 28 Figure 14: Collective Packaging ............................................................................................................ 29 Figure 15: Mechanical Drawing ............................................................................................................. 30 SPECIFICATIONS MANUAL OPN-3102i 1st 1 Abstract This manual provides specifications for the OPN-3102i compact 2D data collector with built-in Bluetooth. 2 Overview The OPN-3102i is 2D imager scanner built-in and output scanned barcode data using the Bluetooth interface. ・OPN-3102i is handy and simple data collector. ・All barcode data scanned is transmitted to a host device through the USB interface or Bluetooth. ・The scanner can work with many Bluetooth-enabled host devices, such as PCs, tablet PCs and smart phones. ・Bluetooth SPP (Serial Port Profile) and HID (Human Interface Device Profile) are implemented. ・Built-in NFC tag facilitate the Bluetooth connection ・The scanner can read barcodes from LCD screens. ・A green LED aiming line toward a target barcode can help the users find the appropriate scanning position. ・Alcohol can be used to wipe the scanner clean ・The power source is 3.7 V 600 mAh (typ.) Li-ion polymer battery. ・The charging is done through a dedicated charging cradle CRD-3000 or USB interface. ・The scanner is Apple MFi certified. SPECIFICATIONS MANUAL OPN-3102i 1st 3 Basic Specifications Item Specification Control Section Input Section Indicator RTC CPU 32 bit CISC / 96 MHz FROM 512 Kbyte + 32 Kbyte SRAM 96 Kbyte FROM (storage) 1 Mbyte Key type 2 key: trigger, function LED 2 bi-colors LEDs (red, green) and 1 blue LED Buzzer Loudness (3-level) / tone adjustable Vibration motor Strength (3-level) / duration adjustable Contents Year, month, date, hour, minute, second Accuracy ± 90 seconds per month Interface Bluetooth NFC tag USB Note For data area only Data and time are lost when the main battery is removed. Frequency 2402 ~ 2480 MHz Specification Bluetooth Ver 2.1 compliant Communication distance 10 m Not guaranteed. Output level Class 2 Max output 4 dBm Profile SPP / HID ISO/IEC 14443 TYPE A, TYPE B JISX6319-4 ・Full-Speed 12Mbps ( HID/COM ) ・Hi-Power Bus-powered supported Optical Section Supported 1D Symbologies Scanning method VGA CMOS area sensor Scanning light source 1 Warm-White LED Aiming light source 1 green LED Effective pixels 0.30 million pixels View angle Horizontal: about 38.0° Vertical: about 26.4° Symbologies UPC-A, UPC-A Add-on, UPC-E, UPC-E Add-on, EAN-13, EAN-13 Add-on, EAN-8, EAN-8 Add-on, JAN-8, JAN-13, Code 39, Tri-Optic, NW-7, Industrial 2 of 5, Interleaved 2 of 5, S-Code, IATA, Code 93, Code 128, MSI/Plessey, UK/Plessey, TELEPEN, Matrix 2 of 5, Chinese Post Matrix 2 of 5, Code 11, Korean Postal Authority code, Postal Code Refer to Chapter 17. for details Minimum resolution Code 39 : 0.1 mm PCS 0.9 Curvature R ≥ 16 mm (10-digit Codabar 0.15mm) R ≥ 20 mm (12-digit UPC) PCS 0.9 Barcode width 100 mm wide 0.2 mm resolution Code 39 (DOF 150 mm) is readable: SPECIFICATIONS MANUAL Item Specification Motion Tolerance 90 ~ 110 Resolution (0.254) 65 ~ 185 Resolution (0.508) 65 ~ 260 Code 128 Resolution (0.2) 85 ~ 165 UPC Resolution (0.33) 55 ~ 195 Depth of Field GS1/Composite Symbologies Minimum resolution Symbologies Supported 2D Symbologies Minimum resolution (mm) PDF417 QR Code DataMatrix Note UPC 100% moving at 2m/sec (DOF 100 mm) is readable: Resolution (0.127) Code 39 Depth of field (mm) OPN-3102i 1st GS1 DataBar , GS1 DataBar Limited, GS1 DataBar Expanded, Composite GS1 DataBar, Composite GS1-128, Composite EAN, Composite UPC GS1 DataBar : 0.127mm Composite Code: 0.127 mm PDF417 , MicroPDF417 , Codablock F , QR Code , MicroQR Code , Data Matrix ( ECC 0 - 140 / ECC 200 ) , MaxiCode( Modes 2 to 5 ) , Aztec Code , Chinese-sensible code PDF417 : 0.169 mm QR Code : 0.169 mm DataMatrix : 0.169 mm Resolution (0.169) 85~ 135 Resolution (0.254) 65 ~ 180 Resolution (0.212) 90 ~ 110 Resolution (0.381) 55 ~ 180 Resolution (0.254) 85 ~ 135 GS1 DataBar: formerly called “RSS” Disable Code 128 when Codablock F is enabled. PCS 0.9 PCS 0.9 TBD Pitch : ±70° Scan angle Skew : ±70° Common Tilt Minimum PCS : ±360° 0.2 or more Scanning from LCD screen MRD 32% or more White brightness 30 cd/m2 or more Contrast ratio 100:1 or more Power Section Main battery Lithium-polymer 600 mAh (typ.) Up-time 10 hours or more Feeding system Electromagnetic guidance wireless charging, microUSB Operating (charging) voltage 4.5 ~ 5.5V Current consumption Charging Less than 500 mA Operating -10 ~ 50°C Storage -20 ~ 60°C Operating 20 ~ 85% Storage 20 ~ 85% Fluorescent 10,000 lx or less Sunlight 100,000 lx or less Temperature Environmental Specifications Humidity Ambient light immunity *1 Charging with USB No condensing No frost SPECIFICATIONS MANUAL Item Specification OPN-3102i 1st Note 10 Hz ~ 100 Hz, acceleration of 19.6 m/s2, 60 minutes per cycle, repeat once in each X, Y and Zdirection Drop the scanner 18 times (6 faces x 3) from a height of 150 cm onto a concrete floor Vibration Drop Dust and drip proof IP54 equivalent LED safety IEC 62471:2006 Exempt_Group EN60950-1:2005 IEC60950-1:2006 EN 55024:2010 EN 55032:2012+AC :2013 EN 301 489-1 V1.9.2 EN 301 489-17 V2.1.1 EN 300 328 V1.9.1 EN 302 291-2 V1.1.1 FCC Part 15 Subpart C, Subpart B ClassB VCCI Class B Product safety Regulatory Compliance EMC Peak Wavelength: 624 nm For residential, commercial and lightindustrial environments CE Marking European conformity Bluetooth logo certification MFi license Other Immunity Test ESD Certification for Construction Design of Specified Radio Equipment No distraction No malfunction Air discharge (direct): ±15 kV Air discharge (direct): ±8 kV Physical Features Dimensions 83.0 × 36 × 21.5 (WDH mm) Weight Approx. 60 g Conditions: IEC61000-4-2 compliant Excluding accessories *1: When a barcode is read twice every 10 seconds at room temperature in a constant Bluetooth connection (SPP master mode). SPECIFICATIONS MANUAL OPN-3102i 1st 4 Detailed View Figure 1: Detailed View No Name Description Scan Window LED illumination is emitted from this window to read barcodes. USB Cap Cap for USB connector part used to make the scanner IP54 water tight. Trigger Key Press this key to enable the laser and start reading barcodes. Function Key The function of this key depends on the installed application. LED Indicates operating status, such as bar code reading, Bluetooth connection, warning etc. Buzzer Orifice Holes for buzzer. Strap Orifice Holes for attaching a hand strap. Charging Coil NFC The charging coil is located here with which the dedicated cradle can supply power to the scanner. This is the location of the NFC tag. Hold an NFC reader close to this area when the tag has to be read. 10 SPECIFIICATIONS MANUAL OPN-3102i 1st 5 Ele ectrical Specifica ations 5.1 USB Su upply Voltage Bu us-power (Cllass) Cu urrent consu umption 5.2 : 4.5-5.5V : 500mA m max (Hi-Pow wer) : Less tha an 500mA Wireless Charging Fe eeding system Po ower consum mption : Electrom magnetic indu uction : Less tha an 5W 6 Intterface Specifica ations The OPN N-3102i supp ports two typ pes of interfacces; USB an nd Bluetooth. 6.1 USB Interfa ace Interface is Fu ull Speed USB interface. 6.1.1 Connectorr Signal Name Contact Num mber VCC DATA A(-) DATA A(+) (NC C) GND Figure 2: micro US SB B Connecttor 6.1.2 USB Interfa ace Circuitt USB Connect ctor Pow wer Sup pply Microcontroller Figure 3:: Interface Circ cuit (USB) 11 SPECIFICATIONS MANUAL 6.2 OPN-3102i 1st Bluetooth The specifications of the OPN-3102i Bluetooth interface are as follows: Frequency : 2402 ~ 2480 MHz 6.3 Specification : Bluetooth Ver 2.1 compliant Communication distance : 10 m Output level : Class 2 (max 4 dBm) Implemented profile : SPP / HID Communication configuration : 1 to 1 Operating mode in communication : Master / Slave mode Security mode : Authentication supported Encryption : Encryption supported NFC Tag OPN-3102i has NFC tag built-in which record Bluetooth device address. Frequency: 13.56MHz Standard : Recorded Contents: ISO/IEC 14443 TYPE A, TYPE B and JISX6319-4 Total 928 byte NDEF Record #1 type: ”application/vnd.bluetooth.ep.oob” OOB data length: 8 Byte MAC address: 00:12:6A:xx:xx:xx Record #2 type: ”T” TEXT data length: 15 Byte TEXT data: ”00126Axxxxxx” Free area Reserved area *xx will differ according to product. Rewriting from external: possible 12 SPECIFICATIONS MANUAL OPN-3102i 1st 7 Optical Specifications 7.1 Basic Specifications Item Characteristics Scan method CMOS area sensor (white / black) Number of effective pixel (Column) × (Row) 640 × 480 dots Image capture speed (*1) Frame rate 100 fps Focal distance Distance from the front edge of scanner 109.2 mm Horizontal Approx. 38.0° Vertical Approx. 28.9° Diagonal Approx. 46.4° Color Warm white Color temperature 2600~3700K Radiant efficiency(*2) 114lm/W Color Green Peak wavelength 535 nm Radiant efficiency (*2) 114lm/W View angle Illumination light source (LED × 1) Aiming light source (LED × 1) *1 *2 The fastest seed of image capture Reference value extracted from the LED datasheet. 13 SPECIFIICATIONS MANUAL 7.2 OPN-3102i 1st Aiming Patttern The aiming iss used for the following p purpose: 1. Fill light to o recognize th he appropria ate reading ra ange. 2. Fill light when auto trig gger is used. The aiming specifications s are as follo ows: - The horizon ntal width of the imaging field of view and the horizontal aiminng width are equal at a distance of L=144.2±4 40 mm from the front edg ge of the sca anner. - The horizon ntal imaging field of view at a distance of L=144.2 2 mm is 0%±±10% of the horizontal aiming width. Fiigure 4: Aimin ng Pattern and d Imaging Range 14 SPECIFICATIONS MANUAL OPN-3102i 1st 8 Technical Specifications Aim the laser light at the center of a code to scan it. The conditions for technical specifications are as follows, unless otherwise specified in each section.Ambient Temperature and Humidity Ambient Light Angles Curvature Power Supply Voltage PCS (1D and 2D) Scanning Test Barcode Test Sample (1D and 2D) Room temperature, room humidity 100 ~200 lux (on the surface of a barcode) Pitch: α = 0°, Skew: β = 15°, Tilt: γ = 0° R=∞ 5.0 V (USB) 0.9 or higher Accept the performance with 90% or more success rate for 10 tries of scan. One reading should be 2 seconds. Specified below. < Test chart > For 1D codes, OPTOELECTRONICS test samples For GS1 Databar, stacked codes and 2D codes, printed by a dedicated printer for barcode β γ Center of image Figure 5: Scanning conditions 15 SPECIFICATIONS MANUAL 8.1 OPN-3102i 1st Barcode Test Sample 1D Barcodes Resolution 0.1 mm (3.9 mil) 0.127 mm (5 mil) 0.20 mm (7.9 mil) 0.254 mm (10 mil) 0.508 mm (20 mil) Symbology PCS Code 39 0.9
Resolution 0.20 mm (7.9 mil) Symbology Code 128
Resolution 0.330 mm (13 mil) Resolution 0.150 mm (6 mil) Size (mm) 8.5 × 10 32 × 10 100 × 10 32.5 × 12 36 × 25 No. of Digits 15 31 PCS 0.9 Size (mm) 42 × 10 No. of Digits 16 Symbology PCS Size (mm) No. of Digits 12-digit UPC 12-digit EAN 0.9/0.2 31.5 × 25.0 12/13 Symbology Codabar(NW-7) PCS 0.9 Size (mm) 20 × 10 No. of Digits 10 PCS 0.9 0.9 Size (mm) 12 × 1.5 12 × 3.0 No. of Digits 14 26 Error Correction PCS No. of Character Level-3 0.9 Size (mm) 23 × 10 35 × 15 Error Correction PCS No. of Character 0.9 Size (mm) 5×5 11 × 11 Model PCS Size (mm) 4×4 No. of Character GS1 Databar/Composite Resolution Symbology 0.169 mm (6.7 mil) Limited 0.169 mm (6.7 mil) Limited-Composite 2D Codes Resolution 0.169 mm (6.7 mil) 0.254 mm (10 mil) Resolution 0.212 mm (8.4 mil) 0.381 mm (15 mil) Resolution 0.212 mm (8.4 mil) ECC200 0.9 0.254 mm (10 mil) * The size is outline dimensions excluding the quiet zones. 6×6 58 44 40 16 SPECIFICATIONS MANUAL 8.2 OPN-3102i 1st Scan Area and Depth of Field The scanner is able to read in the area between the two arcs that are centered on the scan origin with a center line distance from the front of the scanner as indicated for each resolution. Symbology Code 39 Code 128 UPC PDF417 QR Code Data Matrix Barcode Sample Angle Resolution 0.127mm 0.254mm 0.508mm 0.20mm 0.33mm 0.169mm 0.254mm 0.169mm 0.381mm 0.212mm 0.254mm Depth of Field (mm) 60 ~ 105 70 ~ 205 80 ~ 390 80 ~ 165 65 ~ 260 65 ~ 125 50 ~ 180 70 ~ 95 35 ~ 225 60 ~ 130 50 ~ 150 The above codes specified in Chapter 8.1 α = 0°, β =+15°, γ = 0° 17 SPECIFICATIONS MANUAL 0" 2" 4" 6" 8" 50 100 150 200 OPN-3102i 1st 10" 12" 14" 16" 17" [ inch ] 350 400 450 5" 300 150 250 5" 125 0.20mm ( 7.9mil ) 100% EAN/UPC 0.33mm( 13mil ) 0.169mm( 10mil ) PDF417 0.254mm( 10mil ) 0.169mm( 6.7mil ) QR Code 0.381mm( 15mil ) 0.212mm( 8.4mil ) Data Matrix 0.254mm( 10mil ) Figure 6: Scan Area and Depth of Field 18 [ inch ] 0.508mm ( 20mil ) [ mm ] Code 39 6" 150 0.254mm ( 10mil ) Code 128 4" 100 0.127mm ( 5mil ) 3" 75 2" 50 25 1" 0" 25 1" 50 2" 75 3" 100 4" 125 6" [ mm ] SPECIFICATIONS MANUAL 8.3 OPN-3102i 1st Printed Contrast Signal (PCS) 0.2 or higher MRD : 10% and higher (70% or higher reflectivity of space and quiet zone) Distance : 125mm from the front edge of the scanner Barcode Sample : UPC specified in Chapter 8. (Resolution: 0.33 mm, PCS: 0.3) MRD = Minimum reflectance of white bar - Maximum reflectance of black bar PCS = Reflectance of white space – Reflectance of black bar Reflectance of white space * Be sure to keep the optical window clean without dirt or scratches, or it may have a detrimental effect on the reading characteristics. 8.4 Minimum Resolution 1D Code GS1-Databar Stacked Code 2D Code : 0.1 mm (3.9 mil) Code 39 specified in Chapter 8.1 : 0.127 mm (5 mil) GS1 Databar Limited specified in Chapter 8.1 : 0.169 mm (6.7 mil) PDF417, GS1 Databar Limited Composite specified in Chapter 8.1 : 0.169 mm (6.7 mil) QR Code, Data Matrix specified in Chapter 8.1 Barcode Sample Distance Angle Curvature 8.5 The above codes specified in Chapter 8.1 95 mm from the front edge of the scanner α = 0°, β =+15°, γ = 0° R=∞ Barcode Width Code 39 with width of 100 mm and resolution of 0.2 mm can be read Barcode Sample Distance Angle Curvature 0.20 mm Code 39 / PCS 0.9 specified in Chapter 8.1 150 mm from the front edge of the scanner α = 0°, β =+15°, γ = 0° R=∞ Figure 7: Wide Barcode 19 SPECIFICATIONS MANUAL 8.6 OPN-3102i 1st Pitch, Skew and Tilt Pitch Skew Tilt : α = ±70° : β = ±70° : γ = ±360° Barcode Sample : 0.33 mm UPC specified in Chapter 8.1 Distance : 125 mm from the front edge of the scanner Curvature :R=∞ * For the pitch angle and tilt angle measurement, set the skew angle β = +15° β γ Figure 8: Pitch, Skew and Tilt 8.7 Curvature 0.33 mm 12-digit UPC: 0.15 mm 10-digit Codabar(NW-7): Barcode Sample Distance Angle R ≧ 20 mm R ≧ 16 mm 0.33 mm UPC, 0.15 mm Codabar specified in Chapter 8.1 105 mm from the edge of the scan engine Skew angle β = +15° バーコード Barcode Figure 9: Curvature Note: The reading performance may deteriorate if there is specular reflection of the laser light, this typically will occur when the reflectivity of the barcode is high. 20 SPECIFICATIONS MANUAL 8.8 OPN-3102i 1st Scanning from LCD Screen Barcodes displayed on LCD screens (brightness of white part 30 cd/m2 or more, contrast ratio 100:1 or more) can be read. Barcode Ambient light Distance Angle LCD screen type Illumination mode Contrast ratio = : UPC, resolution 0.33 mm specified in Chapter 8.1. : 100 lx or less : 95 mm from the front edge of the scanner : α = 0°, β = 0°, γ = 0° : Transmissive (backlight) TFT : Disable Brightness of white parts Brightness of black parts * The barcode resolution is the value when displayed on the LCD screen. * The width of barcode element is an integral multiple of pixel width of LCD screen. * The reading characteristics may deteriorate due to the specular reflection of LED illumination when the reflectivity is high. 8.9 Motion Tolerance UPC 100%/EAN can be read when it is moving at 2.54m/s. Ambient Temperature and Humidity Ambient Light Distance PCS (1D and 2D) Barcode Sample : Room temperature and Room humidity : 500 ~ 1000 lux : 125 mm from the front edge of the scanner : 0.9 or higher : UPC 0.33mm specified in Chapter 8.1. Figure 10: Motion Tolerance * Scanning may fail due to the specular reflection of LED illumination when the reflectivity is high. 21 SPECIFICATIONS MANUAL OPN-3102i 1st 9 Environmental Specifications 9.1 Temperature Scanning performance is guaranteed when the ambient temp. is within the following range: Operating Temperature: Storage Temperature: -10 ~ 50 °C -20 ~ 60 °C * Please charge when the temperature is between 0 and 40°C. When the temperature is over 40°C, charging may stop to prevent battery breakdown. 9.2 Humidity Scanning performance is guaranteed when the ambient humidity within following range: Operating Humidity: 20 ~ 85%RH (no condensation, no frost) Storage Humidity: 20 ~ 85%RH (no condensation, no frost) 9.3 Ambient Light Immunity Scanning performance is guaranteed when the illumination on a barcode surface is between zero and the following values: Incandescent light: Fluorescent light: Sunlight: Barcode: Distance: Angle: Curvature: Power-supply voltage: 10,000 lx 10,000 lx 100,000 lx 0.33 mm JAN specified in Chapter 8.1. 95 mm from the front edge of the scanner α = 0°, β =+15°, γ = 0° R=∞ 3.7V * Avoid direct or specula reflection from the light source as it may blind the scanners optical receiver. 9.4 Dust and Drip Proof IEC IP54 equivalent Protection against solid objects: Level 5 equivalent (Dust proof type) Prevent dust ingress to inside. Even if slight dust intrusion will not inhibit normal operation. Protection against liquids: Level 4 equivalent (Splash proof type) Protected against water splash from any direction. * () is JIS drip-proof type. 22 SPECIFICATIONS MANUAL 9.5 OPN-3102i 1st Vibration Strength (without packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in non-operating state. Repeat this in each X, Y and Z direction. 9.6 Vibration Strength (in individual packing) There shall be no sign of malfunction after the following vibration test. Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state. Repeat this in each X, Y and Z direction. 9.7 Drop Impact Strength (without packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop the scanner 18 times in total (3 times at each 6 face), from a height of 150 cm onto a concrete floor as shown below. 150cm Figure 11: Drop Test 9.8 Drop Impact Strength (in individual packaging) There shall be no sign of malfunction after the following drop test. Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges, and 6 faces, from a height of 150 cm onto a concrete floor. 9.9 Electrostatic Discharge Immunity Air discharge ±8 kV max. (No malfunction) ±15 kV max. (No destruction) Measurement environment Discharge resistance Charging capacitor An electrostatic testing device compliant with IEC 61000-4-2 330 Ω 150 pF 23 SPECIFICATIONS MANUAL OPN-3102i 1st 10 Regulatory Compliance 10.1 LED Safety IEC 62471:2006 Exempt_Group 10.2 Product Safety EN60950-1:2005 IEC60950-1:2006 10.3 EMC R & TTE Directive ・EN 55024:2010 ・EN 55032:2012+AC:2013 ・EN 301 489-1 V1.9.2 ・EN 301 489-17 V2.1.1 ・EN 300 328 V1.9.1 ・EN 302 291-2 V1.1.1 FCC Part 15 Subpart C, Subpart B ClassB Federal Communications Commission Notices This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Harmful Interference Notice This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment or devices • Connect the equipment to an outlet other than the receiver's • Consult a dealer or an experienced radio/TV technician for assistance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. VCCI Class B This is a Class B product, to be used in a domestic environment, based on the Technical Requirement of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. 24 SPECIFIICATIONS MANUAL OPN-3102i 1st 10.4 O Other ・Bluetooth lo ogo certification ・MFi license “Made forr iPod,” “Made for iPhone,” a and “Made forr iPad” mean that an electronic accessory ha as been design ned to connect sp pecifically to iP Pod, iPhone, o or iPad, respectively, and has be een certified by b the develop per to meet Ap pple performance standards.Apple is not re esponsible forr the o this device or its complian nce with safetty and operation of regulatory standards. Please note tha at the use of th his hone, or iPad may affect wirreless accessory with iPod, iPh performance. ・Certification n for Construc ction Design n of Specified d Radio Equipment ・Classifica ation of Specified Radio Equ uipment ・Model Na ame ・Certificate e Number Article 2 Para agraph 1, Item m 19 Low poower data ccommunicatio on system in 2.4 GHz band OPA-26X1 201-125603 11 Ro oHS Ro oHS complia ance. Ro oHS: The resstriction of the use of certtain hazardous substances in electriccal and ele ectronic equipment, 2011 1/65/EU 12 Re eliability MTBF (M Mean Time Between Failures) 50,0 000 hours 13 Precaution ns Ha andle this prroduct carefu ully. Do not d deliberately subject it to any of the folllowing. (1) Shock: ・ Do not drop p this produc ct from a heig ght greater th han specified d in this man ual. ・ Do not placce this product under or b between any heavy items s. ・ Do not swin ng the cable around. (2 2) Temperatu ure Condition ns: ures outside the specified range. ・ Do not use this product at temperatu ・ Do not pour boiling wate er on this pro oduct. ・ Do not throw this product into a fire.. (3 3) Foreign Ma aterials: ・ Do not imm merse this pro oduct in wate er or other liq quid. ・ Do not expo ose this prod duct to chem micals. Otthers ・ Do not disa assemble this s product. ・ Do not use this product near a radio o or a TV. It may m cause re eception pro blems. ・ This producct may be afffected by a m momentary voltage drop caused by ligghtning. 25 SPECIFICATIONS MANUAL OPN-3102i 1st ・ Do not attach piece of metal or metal foil to the back of charging coil stored part and NFC coil stored part. Also, do not fix anything that prevents placing to charging cradle. ・ Please securely close the USB cap to keep the waterproof. ・ Do not pull strong, fold and bend the cables. ・ Do not add shock or apply load to jack and connector. ・ When charging is completed, please remove USB cable from connector. 13.1 Radio Law This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data communication system and has obtained the Certification for Construction Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan. The following activities are prohibited under the Radio Law: ・Remodeling and disassembly ・Peeling off the certificate label Do not use this equipment under the following environment, as radio interference may affect other device and end up with causing physical or material damage. ・Safety apparatus and medical device for human body protection ・Environment where is concerned to cause serious damage 13.2 Bluetooth ・This product supports Bluetooth wireless communication with other Bluetooth devices that have the same profile ・This product complies with Bluetooth standards; however, its communication performance with untested devices is not guaranteed. ・Bluetooth devices use the 2.4 GHz frequency band that is shared among other devices. It may affect the communication speed and distance between this product and the host device. ・The communication speed and distance vary depending on the interference and radio wave condition between this product and the host device. 13.3 Frequency Band This product uses the 2.4 GHz frequency band. Read carefully the followings before using this product. In the frequency band of this product, scientific, medical and industrial devices including microwaves are used. Also other radio stations including local private radio station for mobile object identification requiring license for such as manufacturing lines at factories, specific power-saving radio station requiring no license and amateur radio station are managed. 1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before using this product. 2. In case that radio interference occurs between this product and “other radio stations,” change the service space immediately, or stop transmitting radio wave to avoid the interference. 3. If you have any questions or troubles, please contact our sales office. * This specification manual is subject to change without prior notice. 26 SPECIFICATIONS MANUAL OPN-3102i 1st 14 Product Labels The product labels are affixed to the scanner as shown below. Unit: mm Figure 12: Product Label Position 27 SPECIFIICATIONS MANUAL OPN-3102i 1st 15 Pa ackaging g Specific cations 15.1 In ndividual Packaging Asssembled pa ackage size: 125 × 112 × 40 (WDH mm) Weight: Appro ox. kg OPN-3102 Place in nto the box with folded side down without taped. *Place with w Opticon lo ogo upward. Displaay for the Serrial-No. 『123456』 123456=Prodduct serial num mber. Dispplay 6-digets serial number. Put MicroUSB B cable and product side by b side. Make it thinne er so as not to overlap on the e product. Place the connecter on right side e at the back. and taped side Place neck strap on to op of USB cable conne ctor, and place QSG at the top. Individdual box label: 3A0002 *Do not fo old the barcode w when pasting Figure 13 3: Individual Packaging 28 SPECIFIICATIONS MANUAL OPN-3102i 1st 15.2 C Collective Packaging 10 00pcs per bo ox Asssembled pa ackage size Weight: Appro ox. kg : 595 × 520 0 × 245 (WDH mm) Thhe order of serial--No. Pa acking box: 5B000 08 (100pcs per boox) Enter battery type 「Lithium ion battery」and pho one number 「01--2422-31-31」. An nd place 1pc next to either side of th he packing box lab bel. 5 St Steps A: Barcode Serrial Label for Pack king Box Stick the labelss on both front and d back side of the box B: Missing Serial Numb ber Label: Attach this label when there are more thaan 3 labels of whiich seriall number s are out of order (not in aa correct sequence e). o mark’ on the trays and the boxes for the e product indic cates that the product is RoH HS compliant which is Note: ‘Ro declared by Optoelectrronics Co., Ltd d. Figure 14 4: Collective Packaging 29 SPECIFICATIONS MANUAL OPN-3102i 1st 16 Physical Features 16.1 Dimensions 83.0 × 36.0 × 21.5 (DWH mm) 16.2 Weight Approx. 60 g (excluding accessories) 16.3 Mechanical Drawing Unit: mm Figure 15: Mechanical Drawing 30 SPECIFICATIONS MANUAL OPN-3102i 1st 17 Supported Symbologies 17.1 Default Setting The scanner is set to default by reading the following menu label. Recorded contents of the NFC tag will also return to default. Default @MENU_OPTO@ZZ@SO@ZZ@OTPO_UNEM@ 17.2 Supported Symbologies 17.2.1 1D Barcodes Code type UPC UPC Add-on 2 UPC Add-on 5 EAN(JAN) EAN Add-on 2 EAN Add-on 5 EAN-13 EAN-13 Add-on 2 EAN-13 Add-on 5 EAN-8 EAN-8 Add-on 2 EAN-8 Add-on 5 Code 39 ○ Minimum length ○ Default Remarks ○ ○ ○ Not transmit ST/SP Tri-Optic ○ Not transmit ST/SP Codabar (NW7) ○ Not transmit ST/SP Industrial 2of 5 ○ Interleaved 2of 5 S-Code Code 128 ○ ○ Code 93 ○ IATA ○ MSI/Plessey UK/Plessey Telepen Code 11 Matrix 2 of 5 Chinese Post Matrix 2 of 5 Korean Postal Authority Intelligent Mail Barcode POSTNET JPN (Customer Barcode) GS1 conversion (setting required) 31 SPECIFICATIONS MANUAL OPN-3102i 1st 17.2.2 GS1 Databar, Composite Code Code type GS1 DataBar ・GS1 DataBar Omnidirectional ・GS1 DataBar Truncated ・GS1 DataBar Stacked ・GS1 DataBar Stacked Omnidirectional GS1 DataBar Limited GS1 DataBar Expanded ・GS1 DataBar Expanded ・GS1 DataBar Expanded Stacked Composite GS1-DataBar ・CC-A ・CC-B ・Limited CC-A ・Limited CC-B ・Expanded CC-A ・Expanded CC-B Composite GS1-128 ・CC-A ・CC-B ・CC-C Composite EAN ・EAN-13 CC-A ・EAN-13 CC-B ・EAN-8 CC-A ・EAN-8 CC-B Composite UPC ・UPC-A CC-A ・UPC-A CC-B ・UPC-E CC-A ・UPC-E CC-B Default Remarks ○ GS1 conversion (setting required) ○ ○ GS1 conversion (setting required) GS1 conversion (setting required) GS1 conversion (setting required) GS1 conversion (setting required) 17.2.3 2D Codes Code type PDF417 Default Remarks ○ Micro PDF417 Codablock F QR Code ○ Micro QR ○ Data Matrix (ECC 200) ○ GS1 conversion (setting required) GS1 conversion (setting required) Data Matrix (ECC 000-140) Aztec Code ○ Aztec Runes Chinese-sensible code Maxi Code 32
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Format : application/pdf Creator : kokamoto3218 Title : Microsoft Word - SS16057(SS15033)_P-X44Xi_Preliminary_160527_Eng.docx Create Date : 2016:10:24 20:18:34+09:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2016:10:24 20:18:34+09:00 Producer : Acrobat Distiller 8.3.1 (Windows) Document ID : uuid:b71492d5-5ee5-4e95-8ffb-d442435fe1b0 Instance ID : uuid:a16c730c-9db6-4d05-a414-5ff249008210 Page Count : 32 Author : kokamoto3218EXIF Metadata provided by EXIF.tools