ORION ELECTRIC M2F9A TV interface Device User Manual Manual 2

ORION ELECTRIC CO., LTD. TV interface Device Manual 2

Contents

Manual 2

31Basic setupRepeat the step 1 on page 30. Then press SET + or– to select the “ADD/DELETE” and press ENTER.1To ADD/DELETE channelsPress VCR MENU until the menu screen iscleared.3To Add or Delete desired channels21) Press Direct channel selection buttons (0–9)or SET +/– to select a channel number you wantto add or delete.2) To add channelsPress ENTER until “ADD” appears on the screen.To delete channelsPress ENTER until “DELETE” appears on thescreen. The channel number will blink3) Repeat 1) to 2) to add or delete other channel.Noise eliminationWhen you don't want to receive a weak signal broadcast, a Blueback screen can be obtained by selecting the NO NOISE BACK-GROUND “ON”. When the unit is shipped from the factory, theNO NOISE BACKGROUND is set to “ON”.Repeat the steps 1~2 on page 29 and press SET+ or – to select “NO NOISE BACKGROUND”.1Press ENTER to select “ON” or “OFF” position.2⟨⟩Press VCR MENU until the menu screen iscleared.30–9ENTERVCR MENU⟨⟩SET +/– 2F90201A (E)p29-34 4/4/05, 9:02 PM31
32Playback (VCR)Loading and unloading a cassette tapeUse only video cassette tapes marked .LoadingRemove the erase prevention tab with a screwdriver. Cover the hole with a piece of adhesive tape.To record againScrewdriverAutomatic tape ejectThis DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning,the cassette tape will be ejected automatically.Push the center of the tape until it is automaticallyinserted.Insert the cassette tape with its labeled side facing upand the erase prevention tab positioned at your left. Aninverted cassette tape cannot be inserted.Automatic playbackWhen loading a cassette tape without an erase prevention tab, playback will start automatically.Automatic power ONWhen you insert a cassette tape the DVD/VCR power will turn ON automatically.2Erase prevention tabAdhesive tapeRemove the cassette tape.Erase prevention tabUnloadingTo prevent accidental erasureTo prevent accidental erasureTape speed and maximum recording timeVideo cassette tapeTape SpeedSLP (Super Long Play)T-160 T-120 T-90 T-60 T-302-2/3 hours 2 hours 1-1/2 hours 1 hour 30 minutes8 hours 6 hours 4-1/2 hours 3 hours 1-1/2 hoursSP (Standard Play)EJECTorPress EJECT on the front panel or on the remote.1 2F90201A (E)p29-34 4/4/05, 9:02 PM32
33Playback (VCR)Cassette tape playbackTo play a prerecorded tape.Load a prerecorded tape(When loading a cassette tape without the eraseprevention tab, playback will start automatically).Preparation:• Turn ON the TV and select the corresponding video input.• Press DVD/VCR to operate the DVD/VCR.• Press DVD/VCR SELECT to select the VCR mode.(The VCR indicator will light).1Press PLAY.Playback will start. “ ” will appearon the screen for about 4 seconds.Press STOP once.The tape will stop but remain fullyloaded and ready to play.“” will appear on the screen forabout 4 seconds.To stop playbackStop the playback or recording via STOP on remote.To discontinue the tape-winding, press STOP. To switch toplayback directly (without STOP), press PLAY.Notes:• This VCR selects the playback tape speed SP, LP or SLP au-tomatically.• The Cassette tape and DVD disc can be played back simulta-neously. If you press DVD/VCR SELECT, the tape playbackand DVD playback alternate with each other on the screen(via CH3, 4 or video connection).2To start playbackPlayback Rewind or forward the tapeTo rewind the tape:Press REV.To forward the tape: Press FF.Forward/Reverse picture search modeWhen the tape is being winded, you can switch to picturesearch mode (see next page). To do this, press REV orFF and hold it down. The unit will resume the tapeadvance or rewinding as soon as the button is released.PLAYSTOPFFREVDVD/VCRDVD/VCR SELECT 2F90201A (E)p29-34 4/4/05, 9:02 PM33
34Playback (VCR)Special playbackPicture searchReverse picture search functionPress REV once or twice during playback.Forward picture search functionPress FF once or twice during playback.To return to playback, press PLAY.Press PAUSE/STILL during playback.To resume normal playback, press PLAY or PAUSE/STILL.During playback press SLOW.To return to playback, press PLAY or SLOW.Whenever you insert a tape and start playback, theautomatic tracking feature continuously analyzes the signalto enable optimum picture quality during playback.Press PAUSE/STILL during playback.Press SLOW repeatedly: The picture advances frame byframe.To return to playback, press PLAY or PAUSE/STILL. Slow tracking and vertical lock adjustmentIf noise bars appear in the picture during slow motion,press the SET + /– to reduce the noise bars.If the still picture jitters excessively, press SET +/– tostabilize the still picture.Automatic tracking adjustmentIf automatic tracking cannot eliminate noises well duringplayback, press SET +/– to eliminate the noise. “MANUALTR.” will appear on the screen. Press it briefly for a fineadjustment, or press and hold for a coarse adjustment.Manual tracking adjustmentSPEED SEARCH TIMESAdjusting tracking conditionStill pictureSlow motionFrame by frame pictureNotes:•The audio output is muted during PICTURE SEARCH, STILL,FRAME ADVANCE and SLOW MOTION.• During picture search mode there will be noise bars. This isnot a defect.• Playback will commence after approx. 5 minutes to protectthe video tape against excessive wear during pause mode.Press ATR to reactivate automatic tracking again.“AUTO TR.” will appear on the screen.PICTURE SEARCH SPEEDPRESS TWICETAPE SPEED PRESS ONCESP (Standard Play)LP (Long Play)SLP (Super Long Play)5 X9 X15 X3 X7 X9 XREVPLAYFFSLOWAT RPAUSE/STILLVideo head cleaningVideo head cloggingThe video heads are the means bywhich the DVD/VCR reads the picturefrom the tape during playback. In theunlikely event that the heads becomedirty enough to be clogged, no picturewill be displayed. This can easily bedetermined if, during playback of aknown good tape, there is good sound,but no picture (picture is extremelysnowy). If this is the case, have theDVD/VCR checked and cleaned byqualified service personnel.Notes:•DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS ORSERVICE THE UNIT BY REMOVING THE REAR COVER.•Video heads may eventually wear out and should be re-placed when they fail to produce clear pictures.•To help prevent video head clogging, use only good qual-ity VHS tapes. Discard worn out tapes.Good PictureSnowy PictureCM skipPress CM SKIP during playback. The DVD/VCR will searchforward through approximately 30 seconds of the tape (e.g.unwanted commercial time) for each press of CM SKIP (maxi-mum six presses) and then resume normal playback.For example : 1 press: 30 seconds of tape2 press: 60 seconds of tape3 press: 90 seconds of tapeCM SKIPSET +/– 2F90201A (E)p29-34 4/4/05, 9:02 PM34
35Playback (VCR)Convenience functionTo cancel repeat mode:Follow the above step 1, then press ENTER to select“OFF” position. Press VCR MENU to return to the TV.Press VCR MENU.Press SET + or –to select “AUTOREPEAT”.1Press ENTER to select “ON” or “OFF”.If “ON” is selected, the playback willbe repeated endlessly.2Press VCR MENU until the menu screen iscleared.If you press CALL, “ ” will appearon the screen .3To commence playback, press PLAY.The playback will be repeatedendlessly.4This function rewinds the tape to the “00:00:00”counter positionautomatically.Press CLOCK/COUNTER.The counter display shows the tape run-ning time during playback or recording.1Press COUNTER RESET at the desired tapeposition.The counter display will be reset to“00:00:00” position (e.g. the beginningof recording).2Press STOP when playback or recording iscompleted.Press ZERO RETURN.The tape will automatically rewind or fastforward to the “00:00:00” counter posi-tion.3Repeat playbackThe entire video tape will play until its end. The tape willautomatically rewind to the beginning and the playback will berepeated.Zero return functionPLAYVCR MENUSET +/–ENTERSTOPZERO RETURNCLOCK/COUNTERCALLCOUNTER RESET 2F90201A (E)p35-40 4/4/05, 9:02 PM35
36Playback (VCR)This function enables you to locate the beginning of any recordingmade on the VCR.Recording an INDEX markThe Index Search function auto-matically records an INDEX markon the tape whenever a recordingis initiated.Index searchPress VISS + or – during stop or play mode.For Succeeding programs: Press VISS +.For Preceding programs: Press VISS –.(As many as 9 index points can be accessed via thismethod.)SQPB (S-VHS Quasi Playback)You can playback video cassette tapes recorded in theS-VHS system.However, the picture will not have the high resolution ofS-VHS system.Note: You cannot record S-VHS video format with this VCR.Notes:• When you record an INDEX mark at the very beginning of thetape, the mark may not be found.• During INDEX search, the tape may stop and begin to play at aslightly different location.• INDEX may not function properly with old or worn out video tapes.• INDEX marks may not be found if it is extremely close to the pointwhere the search began.• In recording, if you stop recording temporarily, the INDEX markis not recorded on the tape.Video index search systemPress CLOCK/COUNTER. The clock and tape counteralternate with each other in the display window.Notes:• If you rewind the tape beyond “00:00:00”, a minus sign (“–”)will be displayed in front of the time.• When you load a tape, the counter will reset to “00:00:00”.• The counter does not function on nonrecorded (blank)sections of the tape. When you rewind, fast forward or playtapes through blank sections, the counter stops.Clock/counter displayCOUNTERCLOCKPress DVD/VCR SELECT. The DVD mode and theVCR mode alternate with each other in the display.DVD modeVCR modeINDEX NO. (up to 9)or is displayedSTOPDVD/VCR SELECTVISS+/–CLOCK/COUNTERWhen the VISS + or –is pressed,the unit starts searching the INDEXNO. selected and finds the portion,then playback starts automatically.To stop the Index Search, pressSTOP.Convenience function (continued) 2F90201A (E)p35-40 4/4/05, 9:02 PM36
37Recording (VCR)Recording a TV programRecording and viewing the same TV program.Recording a TV programLoad a cassette tape with the erase preventiontab intact. The DVD/VCR will automatically turn on.1Press SP/SLP to select the desired tape speedSP or SLP.The tape counter and “SP” or “SLP”will appear on the screen for about 4seconds.2Select “TV” or “CABLE” to the appropriateposition .3TV - VHF/UHF channelsCABLE - Cable TV channelsPress Number buttons or CH +/– to select thechannel to be recorded.4Press REC/OTR.“ ” will appear on the screen forabout 4 seconds and “REC” willappear on the display window.5VHF/UHF/CABLE TV CHANNELSTV CABLE TVVHF2-13UHF14-69VHF2-13STD/HRC/IRC 14-36 (A) (W) 37-59 (AA) (WW) 60-85 (AAA) (ZZZ) 86-94 (86) (94) 95-99 (A-5) (A-1)100-125 (100)(125) 01 (5A)TV mode direct channel selection:All channels can be instantly selected by using twobuttons. (for example, to select channel 2, press “0”, then“2”. If you press only “2”, channel selection will be delayedfor two seconds.) For channels 10 and above, press the 2digits in order.CABLE mode direct channel selection:1-9 Press 0 twice and then 1-9 as required.Example: To select “2”, Press 002.10-12 Press 0first and then the remaining 2 digits inorder from left to right.Example: Press 012 for “12”.13-99 Press 2 digits in order.Example: Press 22 for “22”.100-125 Press the 3 digits in order.Example: Press 110 for “110”.0–9REC/OTRCH +/–DVD/VCRPreparation:• Turn ON the TV and select to the correspondingvideo input.• Press DVD/VCR to operate the DVD/VCR.• Press DVD/VCR SELECT to select the VCR mode.(The VCR indicator will light.)SP/SLPDVD/VCR SELECTRecording (VCR) 2F90201A (E)p35-40 4/4/05, 9:02 PM37
38Recording (VCR)Recording one program whilewatching anotherPress STOP to stop recording.“ ” will appear on screen for about 4 seconds.Press PAUSE/STILL to avoid recording unwantedmaterial. Press again to continue the recording.“ ” will appear on screen forabout 4 seconds.Notes:•The pause function will be released after 5 minutes to preventdamage to the tape or the VCR. The VCR will change to theSTOP mode.• You can select a recording channel in the recording pausemode.To stop recording temporarilyWhile the VCR is recording, select your desired channelon the TV.When a TV is connected with an antenna cable only,press TV/VCR to select the TV position.The “VCR” display will go off and recording will continue.Select the TV channel you want to watch by using theTV channel selector.Note:Some Cable TV hookups do not permit viewing one channelwhile recording another. See pages and .This VCR will automatically rewind the tape when the tapehas ended (except during OTR and timer recording). It willalso eject the tape.Auto Rewind featureTo stop recordingTV/VCRSTOPPAUSE/STILLRecording a TV program (continued) 2F90201A (E)p35-40 4/4/05, 9:02 PM38
39Recording (VCR)One-touch Timer Recording (OTR)The One-touch Timer Recording feature provides a simple andconvenient way to make a timed recording.One-touch Timer Recording (OTR)Pressoncetwice3 times4 times5 timesNORMAL REC0:301:001:302:003:004:005:006:00NORMAL RECRecording time Press6 times7 times8 times9 times10 timesRecording timeLoad a cassette tape with the eraseprevention tab intact. The VCR will automatically turn on.1Press SP/SLP to select the desired tape speedSP or SLP.The tape counter and “SP” or “SLP”will appear on the screen for about 4seconds.2Set “TV” or “CABLE” option to theappropriate position .3TV - VHF/UHF channelsCABLE - Cable TV channelsPress Direct channel selection buttons (0–9) orCH +/– to select the channel to be recorded.4PressREC/OTR. Recording begins. Press thebutton again to stop recording after 30 minutes.Each additional press of REC/OTR will increaserecording time as shown in the chart below, upto a maximum of 6 hours.The OTR and recording time willappear on the screen for about 4seconds. And, “ ” will appear onthe display.5To cancel OTRPress STOP or turn off the power.“ ” will appear on screen for about 4 seconds.Note:If you wish to watch the DVD playback during OTR or standardrecording, press DVD/VCR SELECT to change to DVD modeand perform the DVD playback .0–9CH +/–REC/OTRSP/SLPDVD/VCRSTOPPreparation:• Turn ON the TV and select to the correspondingvideo input.• Press DVD/VCR to operate the DVD/VCR.• Press DVD/VCR SELECT to select the VCR mode.(The VCR indicator will light.)Example: One-touch Timer Recording for 30 minutes.DVD/VCR SELECT 2F90201A (E)p35-40 4/4/05, 9:02 PM39
40Recording (VCR)Timer recordingTimer recording can be programmed on-screen with the remote control.The built-in timer allows automatic unattended recording of up to 8programs within 1 month.Timer recordingNotes:• Press CANCEL to move cursor backward for correction.• To record from external source set the channel to “L1” or“L2”.Notes:• If the timer symbol ( ) blinks when the timer recording ended,the TV program has not been completely recorded because ofan insufficient tape length. Press TIMER REC to cancel thetimer program or press EJECT to remove the cassette tape.• During timer recording standby mode, the VCR mode cannot beoperated. To use the VCR, press TIMER REC at first, then pressDVD/VCR SELECT to change to VCR mode. After you use theVCR, press TIMER REC again to put the VCR into timerrecording standby mode.• If you press TIMER REC during timer recording, the recordingoperation will be interrupted. If you press TIMER REC againwithin the programmed time, the recording operation will startagain.• After a power failure or disconnection of the power plug, allprogrammed recording settings and time display will be lostupon resumption of power. In this case, reset the clock andreprogram any timer recording.Press VCR MENU. Select “TIMER REC SET”,then press ENTER.Preparation:• Press DVD/VCR to operate the DVD/VCR.• Press DVD/VCR SELECT to select the VCR mode.• Load a cassette tape with the erase prevention tabintact.• Check the time and date are correct .Example: Program a timer recording for the 26th day,channel 125 (Cable TV), 11:00 - 11:30 PM on timerprogram number 1 (Tape speed: SLP).1Press SET + or – to select one of the programline, then press ENTER.2Press SET + or – to select the date, then pressENTER.3Set the start time, end time, channel and tapespeed as in step 3.4⟨+/—/ENTER/CANCEL/MENU ⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————26(SA)11:00PM11:30PM125SLP⟨+/—/ENTER/CANCEL/MENU ⟩DATE START END CH———————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————26(SA)11:00PM11:30PM125SLPTo enter other programs, repeat steps 2through 4.• To return to the normal screen,press VCR MENU twice.5Press TIMER REC. The timer symbol ( ) willappear on the display and the VCR stands byfor recording.At the same time, VCR mode willchange to DVD mode automatically.You can use DVD even if the VCR isin the timer recording mode.If you do not use the DVD, turn thepower off.6Notes:• The timer recording will start at 5 seconds before the timeyou predetermined.• If the timer symbol ( ) does not appear on the display inspite of the pressing of TIMER REC, the cassette may nothave been loaded .• If the cassette is ejected in spite of the pressing of TIMERREC, the erase prevention tab of the cassette may havebeen removed .• During Timer recording, the power cannot be turned off.SET +/–DVD/VCRENTERCANCELVCR MENUEJECT⟨ ⟩⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH———————:—— —:—— ————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ——————————:—— —:—— ———————————26(SA)TIMER RECDVD/VCR SELECT 2F90201A (E)p35-40 4/4/05, 9:02 PM40
41Recording (VCR)Setting procedureTo set daily/weekly timerTo confirm Timer program:At step 1 on the previous page select “TIMER RECSET” and press ENTER.The timer program list will appear on the screen.2The current day (Friday) SU-SA (Sunday to Saturday)MO-SA (Monday to Saturday)MO-FR (Monday to Friday)WKL-WE WKL-TH (Weekly Thursday)(Weekly Wednesday)One month laterminus one dayWeekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-SA: Monday to Saturday) Timer recordingFollow the procedure of timer recording on the previouspage. At step 3press SET + or –repeatedly until thedesired setting appears. Then press ENTER.When you press SET – repeatedly, theDATE indicator will change as follows, inthis case the day is Friday.If the programs overlap anotherDo not overlap timer programs as portions of theconflicting programs will be lost. The first recordingtime has priority over the next recording time as shownin the diagram below.Notes:• The daily/weekly recording can be made continuously until therecording is canceled or the tape reaches the end.• During timer recording the automatic rewinding mechanismdoes not function.8 : 00 11 : 009 : 00 10 : 00Program 1Prog.1Deleted PartsNon Recorded Portion PartsProg.2 Prog.3Program 2Program 3RecordingControl Settings⟨ ⟩ ⟨+/—/ENTER/CANCEL/MENU⟩DATE START END CH26(SA)11:00PM11:30PM125SLPNotes:• If there are other timer record programs remaining, TIMERREC must be pressed to reactivate the timer, otherwise theremaining timer record programs will be ignored.• You cannot confirm the Timer program during timer recordingoperation.• You can correct or cancel a programmed setting in programconfirm mode.If the Timer has been activated, press TIMERREC to deactivate the Timer.The timer symbol ( ) willdisappear. Then press DVD/VCRSELECT to change to VCR mode.1To cancel Timer program:Press SET + or – to select the unwanted program,then press CANCEL to cancel the program.3Press VCR MENU repeatedly until the menuscreen is cleared.4To confirm or cancel a programSET +/–ENTERVCR MENUCANCELDVD/VCR SELECTTIMER REC⟨ ⟩ 2F90201A (E)p41-44 4/4/05, 9:02 PM41
42Other functions (VCR)Stereo recording and playback/Second Audio Program (SAP)When a MTS STEREO broad-cast is received, “STEREO” willappear on the screen for about 4seconds and the program canbe viewed or recorded in stereo.The Hi-Fi stereo recording pro-cedure is the same as for normalrecordings.Notes:• When playing back a tape that is not recorded in Hi-Fi stereomode, the audio will automatically be monaural.• When listening to a VHS Hi-Fi video tape or MTS broadcastthrough the VHF/UHF jack (Audio/Video cable not connected),the sound will be monaural.When viewing an MTS stereo TV program, or playing aprerecorded VHS Hi-Fi stereo videotape, press AUDIOSELECT to select how the audio will be heard throughthe speakers. Normally set to the Hi-Fi stereo position,this button can be set to the MONO position if the stereobroadcast or videotape audio is of poor quality. The “R”and “L” positions allow the audio from the Right or Left Hi-Fi channel to be heard over both TV speakers. Thisbutton has no effect when viewing a MONO videotape orTV program. Each time when you press the button,OUTPUT SELECTION display appears on the screen forseveral seconds. Refer to the chart below.Output selectionYour DVD/VCR is fitted with a SAP broadcast system whichenables you to switch to a second audio program when view-ing a selected channel.This function applies only when the program is broadcast inmulti-languages through the SAP broadcast system.When the VCR is turned on or a channel selection ismade, make certain the letters “SAP” appears on thescreen for about 4 seconds. This means that the “SecondAudio Program” broadcasting is available.Listening to SAPStereo recording and playbackThe VHS Hi-Fi audio system permits high fidelity record-ing of MTS STEREO TV broadcasts.Second Audio Program (SAP)OUTPUTSELECTIONSTEREOL chR chMONOSOUND HEARD ON BOTHSPEAKERSSTEREOLEFT CHANNEL AUDIORIGHT CHANNEL AUDIOMONOPress VCR MENU. Then press SET + or – toselect “SAP”.1Press ENTER to select “ON”.Then press VCR MENU until themenu screen is cleared.2STEREOORSET +/–ENTERVCR MENUNote:When using a Cable TV system, stereo TV programs maybe transmitted over a mono cable channel. In this case“STEREO” will not appear and the sound will be in mono.AUDIO SELECT 2F90201A (E)p41-44 4/4/05, 9:02 PM42
43Other functions (VCR)To AUDIO (L) OUTAUDIO/VIDEO cable (supplied)Playback VCRTo VIDEO OUT To AUDIO (R) OUTRecording VCRTo AUDIO (L) INTo VIDEO IN To AUDIO (R) INDuplicating a video tapeIf you connect the DVD/VCR to another VCR or Camcorder, you can duplicatea previously recorded tape. Make all connections before turning on the power.Duplicating a video tapeFor duplicating a previously recorded tape from acamcorder, follow the camcorder manufacturer’sinstructions. A typical camcorder dubbing hookup isshown above.AUDIO/VIDEO cable (not supplied)To AUDIO (R) INTo AUDIO (L) INTo VIDEO INRecording VCRTo AV JackPlayback CamcorderConnection with second VCRConnection with CamcorderPress SP/SLP to select the desired tape speedSP or SLP.It is recommended that you set thetape speed to the SP mode on therecording VCR for best results.1Press INPUT SELECT once or twice to selectAUDIO/VIDEO input position.“L1” or “L2” will appear in the display.2Press REC/OTR on the recording VCR. The duplicating process begins.3Press PLAY on the playback VCR or Camcorder.4Press STOP after duplicating a video tape.5L1: on the rear panelL2: on the front panelPreparation:• Turn ON the TV and select the corresponding videoinput.• Press DVD/VCR to operate the DVD/VCR.• Press DVD/VCR SELECT to select the VCR mode.(The VCR indicator will light.)• Load a cassette tape with the erase prevention tabintact.• Load a previously recorded tape into the playbackVCR or Camcorder.REC/OTRSTOPSP/SLPINPUT SELECTDVD/VCR SELECTDVD/VCR 2F90201A (E)p41-44 4/4/05, 9:02 PM43
44Other functions (VCR)Press REC/OTR to start recording.The DVD/VCR will change to theVCR mode automatically and theplayback picture or sound will beduplicated on the video cassettetape.Recording a DVD/CD discYou can record disc material in DVD, Audio CD, etc. onto a Videotape with this DVD/VCR.Duplicating a DVD or CD discPress SP/SLP to select the desired tape speedSP or SLP.Preparation:• Turn ON the TV and select the corresponding videoinput.• Press DVD/VCR to operate the DVD/VCR.• Press DVD/VCR SELECT to select the VCR mode.(The VCR indicator will light.)•Load a cassette tape with the erase prevention tab intact.• Load a DVD/CD disc.1Press DVD/VCR SELECT selector to select theDVD mode.The DVD indicator will light.2Press PLAY to start playback.34Press STOP if you finish recording.If you wish to stop a DVD/CD disc,pressDVD/VCR SELECT selector tochange the DVD mode, then pressSTOP.5Notes:• You may not be able to record the beginning of the disc.Begin VCR recording once program playback commenceson the DVD.• When the scanning mode is set to the progressive mode,you cannot duplicate a disc material onto a video tape.When REC/OTR is pressed, the PROGRESSIVE indicator“” on the display window will flash and “Please Set Off” will appear on the screen.• You cannot record discs encoded with copy guardfunction. The following icon and text will show up on theTV screen.SP/SLPSTOPDVD/VCRPLAYDISC IS COPY PROTECTEDREC/OTRDVD/VCR SELECT 2F90201A (E)p41-44 4/4/05, 9:02 PM44
45Basic playback (DVD)CAUTIONKeep your fingers well clear of thedisc tray as it is closing. Neglectingto do so may cause seriouspersonal injury.Basic playbackPlaying a discThis section shows you the basics on how to play a disc.Basic playback (DVD)Preparations:• When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD. Thismay include S-video or component video inputs which are exclusive to DVD playback.• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the inputconnected to the DVD/VCR.DVDVCDCDPress OPEN/CLOSE or PLAY on the unit.The disc tray closes automatically.On the TV-screen, “ ” changes to“Reading Disc” and then playbackcommences.• A menu screen will appear on the TV screen, ifthe disc has a menu feature.Press / or / to select title.Press ENTER.• Title is selected and playcommences.Press STOP to end playback.• The unit records the stopped point,depending on the disc. “ ”appears on the screen. PressPLAYto resume playback (fromthe scene point).• If you press STOP again or unloadthe disc (“ ” appears on thescreen.), the unit will clear thestopped point.Press ON/STANDBY.The DVD/VCR turns on.Press VCR/DVD SELECT to select the DVD mode.The DVD indicator will light.Press OPEN/CLOSE.The disc tray opens.Place the disc on the disc tray.With the playbackside down• There are two different disc sizes. Place the discin the correct guide on the disc tray. If the disc isout of the guide, it may damage the disc andcause the DVD/VCR to malfunction.• Do not place a disc which is unplayable in thisDVD/VCR.24563789To start playback in the stop modePress PLAY.OR1Press DVD/VCR on the remote control tooperate the DVD/VCR.C/D/B/AENTERDVD/VCR 2F90201A (E)p45-48 4/4/05, 9:03 PM45
46To pause playback (still mode)Press PAUSE/STILL during playback.To resume normal playback, pressPLAY.• The sound is muted during stillmode.To stop playbackPress STOP.Notes:• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screenaccording to the type of loaded disc. In this case, check your disc again 10.• Some discs may take a minute or so to start playback.• When you set a single-faced disc label downwards (i.e. the wrong way up) and press OPEN/CLOSE or PLAY on the unit,“Reading Disc” will appear on the display for a few minutes and then “Incorrect Disc” will continue to be displayed.•Some discs may not work the resuming facility.• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page 54.• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according tothe disc contents the software producers designed, some playback features may not be available. Also refer to theinstructions supplied with the DVDs.• Do not move the unit during playback. Doing so may damage the disc.• Use the OPEN/CLOSE to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may cause theunit to malfunction.• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the unit tomalfunction.• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screenmenu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to pressPOWER on your remote control once the movie is completed.• There may be a slight delay between you pressing the button and the function activating.• The screen saver does not operate when connecting the DVD video player to the TV using the HDMI cable.• If the Media card is inserted during the playback, playback will stop and change to the CARD mode automatically. If you wishto change to the DVD mode, press DVD/CARD.To obtain a higher quality pictureOccasionally, some picture noise not usually visible during a normal broadcastmay appear on the TV screen while playing a DVD video disc because the highresolution pictures on these discs include a lot of information. While the amount ofnoise depends on the TV you use with this unit, you should generally reduce thesharpness adjustment on your TV when viewing DVD video discs.AboutDVD VCD CDCARDTheDVD VCD CD icons on the heading bar show the playable discs for thefunction described under that heading.DVD: You can use this function with DVD video discs.VCD: You can use this function with Video CDs.CD: You can use this function with Audio CDs and CD-R/RW CDs.CARD: You can use this function with Media cards.Screen saver functionThe screen saver operates when you leave the unit inDVD stop mode for approx. five minutes.The screen will repeatedly get dark gradually and backto normal.OPEN/CLOSESTOPPAUSE/STILLPLAYTo remove the discPress OPEN/CLOSE.Remove the disc after the disc trayopens completely.Be sure to press OPEN/CLOSE to close the disc trayafter you remove the disc.POWERC/D/B/APlaying a Disc while the VCR section is recordingor standing by for timer recording1) Start to record.Follow steps 1~5 on page 37.• If the DVD/VCR is standing by for recording, turn onthe DVD/VCR.2) Press DVD/VCR SELECT selector to select DVD mode.3) Play a disc.Follow steps 4 ~ 6 on page 45.• Press PLAY if the DVD/VCR does not start to play adisc automatically.4) Stop to play.Press STOP to stop play back a disc.DVD/VCR SELECTDVD/CARDBasic playback (DVD)Basic playbackDVDVCDCD 2F90201A (E)p45-48 4/4/05, 9:03 PM46
47Basic playback (DVD)Playing a disc (continued)You can play discs at various speeds.Playing frame by frameDVDVCDDVDVCDPlaying in fast reverse or fast forward directionsPress REV or FF during playback.REV: Fast reverse playbackFF: Fast forward playbackEach time you press REV or FF, theplayback speed changes.To resume normal playbackPress PLAY.Notes:• The DVD/VCR mutes sound and subtitles during reverseand forward scan of DVD/VCD video discs. However, thisunit plays sound during fast forward or fast reverse play ofaudio CDs.• The playback speed may differ depending on the disc.Press PAUSE/STILL during still playback.Each time you press PAUSE/STILL,the picture advances one frame.To resume normal playbackPress PLAY.Note:The sound is muted during frame by frame playback.Press SLOW ( ) during playback.Each time you press the button, theslow-motion speed changes.To resume normal playbackPress PLAY.Note:The sound is muted during slow-motion playback.Press SKIP or repeatedly to display the chapter or track number you want.Playback starts from the selected chapter or track.To locate succeeding chapters ortracks.Playback starts from the beginning of thecurrent chapter or track.When you press twice in quick successions,playback starts from the beginning of thepreceding chapter or track.• A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you tried is notavailable on the disc, or the DVD/VCR cannot access the feature at this time. This does not indicate a problem with the DVD/VCR.• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leavethe still video image or On screen display image displayed on your TV for an extended period of time, you risk permanentdamage to your television screen. Projection televisions are very susceptible.Notes:Locating a chapter or trackPlaying in slow-motionDVDVCDCDDVDVCDCDFFREVPLAYPAUSE/STILLSKIP /SLOW 2F90201A (E)p45-48 4/4/05, 9:03 PM47
48Zooming12Press ZOOM during playback.The center part of the image will bezoomed in.Each press of ZOOM will change theZOOM 1 (x 1.3), 2 (x 1.5) and 3(x 2.0).Zooming/Locating desired sceneThis unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.Press CCCCC/DDDDD/BBBBB/A A A A A to view a different part of theframe.You may move the frame from thecenter position to UP, DOWN, LEFT orRIGHT direction.3Notes:• You can select the Pause, Slow or Search playback in the zoom mode.• Some discs may not respond to zoom feature.Locating desired sceneUse the title, chapter and time recorded on the DVD disc to locate the desired point to play back. In the case of VCD/CDdiscs, time and track are used to locate the desired point to play back. To check the title, chapter and time, press DISPLAY.1423Note:In case of the Video-CD playback with PBC, the SEARCH does not work. To turn off PBC 54.C/D/B/AZOOM0–9ENTERDISPLAYCLEARSEARCHIn the zoom mode press ZOOM repeatedly toreturn to a 1:1 view ( Off).Press SEARCH during playback or stop mode.Press C C C C C or DDDDDto select the “Time”, “Title” or“Chapter”.Press Number buttons (0–9) to change thenumber.• If you input a wrong number, pressCLEAR.• Refer to the package supplied withthe disc to check the numbers.Press ENTER. Playback starts.• When you change the title,playback starts from Chapter 1 ofthe selected title.• Some discs may not work in theabove operation.1DVDVCDCDDVDVCDCDAdvanced playback (DVD)• “Time” only works in playbackor resume stop mode. 2F90201A (E)p45-48 4/4/05, 9:03 PM48
49Advanced playback (DVD)Marking the scenes Returning to the scenes1Press MARKER during playback or stop mode.213Marking desired scenesThe unit stores the points that you want to watch again up to 3 points.You can resume playback from each scene.23Notes:Some discs may not work with the marking operation.The marking is cancelled when you open the disc tray orturn the power off.Some subtitles recorded around the marker may fail toappear.•••To cancel the MarkerFollow the above steps 1~2, then press CLEAR.DVDVCDDVDVCDENTERCLEARMARKERC/DPress MARKER during playback.Select the blank Marker using C or D.Then press ENTER at the desired scene.• Repeat this procedure to set theother 2 scenes.Press MARKER to remove this display.Press ENTER.Playback starts from the markedscene.Press C or D to select the Marker 1-3. 2F90201A (E)p49-52 4/4/05, 9:03 PM49
50Advanced playback (DVD)Repeat playback1Press PLAYMODE during playback or stop mode.Repeat playback/A-B Repeat playbackPress PLAYMODE again to make the screendisappear.3A-B Repeat playback1Press A-B RPT during playback.The start point is selected.A-B repeat playback allows you to repeat material betweentwo selected points.22DVDVCDCDANotes:• In A-B Repeat mode, subtitles near the A or B locations maynot be displayed.• You cannot set the A-B Repeat for the scenes that includemultiple angles.• A-B Repeat playback does not work when Repeat playback isactivated.• You may not be able to set A-B Repeat, during certain scenesof the DVD.• A-B Repeat does not work with an interactive DVD, MP3/WMA/JPEG CD.• A-B Repeat is prohibited when PBC is on.To resume normal playbackPress A-B RPT again.“Off” appears on the screen.ABDVDVCDCDD/B/APLAYMODEA-B RPTRepeat Off/Play ModeNotes:• Some discs may not work with the repeat operation.• In case of Video CD with PBC, repeat functions are prohib-ited during playback.[DVD]Press BBBBB/AAAAA to select “Chapter” or “Title”.The unit automatically starts repeatplayback after finishing the current ti-tle or chapter.[Audio CD, Video CD, MP3/WMA CD]Press DDDDD to select “Repeat”.Press BBBBB/AAAAA to select “Track” or “All”.The unit automatically starts repeatplayback after finishing the currenttrack.• If you set the repeat mode during stop mode,press PLAY to start Repeat playback.Press A-B RPT again.The end point is selected. Playbackstarts at the point that you selected.Playback stops at the end point, re-turns to Point A automatically, thenstarts again.To resume normal playbackSelect Repeat : “Off” in step 2.PLAYPlay Mode OffRepeat Off/Play Mode 2F90201A (E)p49-52 4/4/05, 9:03 PM50
51Advanced playback (DVD)Program playbackPress PLAYMODE during stop mode.1Press CCCCC/DDDDD/BBBBB/AAAAA to select “Program Playback”and press ENTER.The programs you selected will start to playback inthe order.•In case of JPEG file, press SKIP to continuethe program playback.•To resume normal playback, select Play Mode:“Off” in step 2.4Program playback/Random playbackYou can arrange the playback order of tracks or files on the disc. Andalso the unit selects tracks or files at random and playback them.These feature works for Audio CD, Video CD and MP3/WMA/JPEGCD.VCDCD23Random playbackVCDCDPress CCCCC/DDDDD to select Play Mode, then pressBBBBB/AAAAA to select “Random”.1Press PLAY.The Random Playback will start.32Play Mode RandomRepeat Off/Play ModeNote:In playing back the Video CD with PBC, you cannot setRandom playback.Notes:• In playing back the Video CD with PBC, you cannot setProgram playback.• The program is cancelled when you open the disc tray orturn the power off.Play Mode OffRepeat Off/Play ModeENTERC/D/B/APLAYMODEPLAY0–9CLEAR■To change the program1. In the program mode, press C/D/B /Ato select the tracknumber.2. Press Number buttons (0–9) to select the track numberto be replaced.■To clear the program one by oneIn the program mode, press C/D/B/Ato select the tracknumber. Then press CLEAR.■To clear all the programsIn the program mode, press C/D/B/Ato select “Clear”.Then press ENTER.Press CCCCC/DDDDD to select Play Mode, then pressBBBBB/AAAAA to select “Program”.Press CCCCC/DDDDDor BBBBB/AAAAAto select the programmingposition. Use Number buttons (0–9) to input thetrack or file numbers.• To program others, repeat step 3.• If you input a wrong number, pressCLEAR.Press PLAYMODE during playback or stopmode.• If you set “Random” during playback mode,Random playback will begin after the track that iscurrently being played has ended.• To resume normal playback, select Play Mode:“Off” in step 2.SKIP 2F90201A (E)p49-52 4/4/05, 9:03 PM51
52Advanced playback (DVD)Press CCCCC/DDDDD/BBBBB/AAAAA to select the desired title.Changing angles/Title selection/DVD menuPress ANGLE during playback.The current angle will appear.When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.1Press ANGLE repeatedly until the desired angleis selected.2Note:Depending on the DVD, you may not be able to change theangles even if multi-angles are recorded on the DVD.Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.1Press ENTER or PLAY.The playback of the selected title willstart.3Note:Depending on the DVD, you may not be able to select the title.Depending on the DVD, a “title menu” may simply be called a“menu” or “title” in the instructions supplied with the disc.2Press CCCCC/DDDDD/BBBBB/AAAAA to select the desired item.Some DVDs allow you to select the disc contents using the menu.When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.1Press ENTER.The menu continues to anotherscreen. Repeat steps 2 and 3 to setthe item completely.32Press TOP MENU during playback. Title menu appears on the screen.Press MENU during playback.The DVD menu appears on the screen.• Press MENU again to resumeplayback at the scene when youpressed MENU.Note:Depending on the DVD, you may not be able to resume playbackfrom the scene point when you pressed MENU.ANGLEENTERC/D/B/ATOP MENUPLAYMENUDVD1/9DVDDVDChanging anglesTitle selectionDVD menu 2F90201A (E)p49-52 4/4/05, 9:03 PM52
53Advanced playback (DVD)Changing soundtrack language12Press AUDIO during playback.The current soundtrack language willappear.Changing soundtrack language/Setting surround soundYou can select the language when you play a multilingual disc.Notes:• If the desired language is not heard after pressing thebutton several times, the language is not recorded onthe disc.• Changing soundtrack language is cancelled when youopen the disc tray. The initial default language or availablelanguage will be heard if the disc is played back again.In case of Video CD playbackAudio type changes as follows each time you pressAUDIO.LRQSound OffLQSound OffRQSound OffQSound Off1/8 Eng Dolby Digital2/8 Fra Dolby DigitalQSound OffDVDVCDAUDIOPress AUDIO repeatedly until the desired lan-guage is selected.•The on screen display will disappear after a fewseconds.B/APress Bor A to select “On”.• The on screen display will disappear after a fewseconds.1Setting surround soundThis DVD video player equipped with a “QSound”. It can produce the effect of being in a cinema or a concert hall.2To cancel Surround mode:Follow the left steps 1~2, then press Bor Ato select the“Off” position.Notes:• The “QSound” is effective only for the sound of disc.• The QSound setting can also be changed in the functionsetting .During disc playback press AUDIO.DVDVCDCDQSound Off1/8 Eng Dolby DigitalQSound On1/8 Eng Dolby DigitalSetting surround soundManufactured under license from QSound Labs,Inc. U.S. patent Nos. 5,105,462, 5,208,860 and5,440,638 and various foreign counterpart.Copyright QSound Labs, Inc. 1998-2002.QXpander™is a trademark of QSound Labs, Inc.All rights reserved. 2F90201A (E)p53-58 4/4/05, 9:03 PM53
54Advanced playback (DVD)Subtitles/To turn off the PBCSUBTITLEWhen playing back a disc recorded with subtitles, you canselect the subtitle language or turn the subtitle off.To turn off the subtitle, press SUBTITLE until“Off” appears.• The on screen display will disappear after a fewseconds.1Notes:• Depending on the DVD, you may not be able to changesubtitles, or to turn subtitles on or off.• While playing a DVD, the subtitle may change when youopen or close the disc tray.• In some cases, a selected subtitle language may not bechanged immediately.OffSubtitlesPress SUBTITLE repeatedly during playbackuntil your desired language appears.1/8 Eng2DVDENTERPLAYMODEC/D/B/ATo turn off the PBC (Video CD version 2.0)Press / to select Play Mode, then press/ to select “Off”.1Press PLAYMODE in the stop mode.2Press PLAYMODE again to make the screendisappear.3Follow the above steps 1~2, then press or to select“PBC”.Note:You can also turn off the PBC by pressing number button 1and ENTER in the stop mode.To turn on the PBC1 2F90201A (E)p53-58 4/4/05, 9:03 PM54
55Advanced playback (DVD)MP3/WMA/JPEG operationThis player can play back the MP3/WMA/JPEG-data which has been recorded on CD-R, CD-RW or Media card. To producethe MP3/WMA JPEG-data, you need a Windows-PC with CD-RW drive and a MP3/WMA/JPEG-encoding Software (notsupplied). The Apple-HFS-System cannot be played.Note:This unit requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality.Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats(including CD-R containing MP3/WMA files). Given the fact that technology in this area is still maturing, Toshiba cannotguarantee that all genre of recordable discs will produce optimal playback quality. The technical criteria set out in thisowner’s manual are meant as a guide only.Please be advised that you must obtain permission from the applicable copyright owners to download copyrightedcontent, including music files, in any format, including the MP3 and WMA formats, prior to the downloading thereof.Toshiba has no right to grant and does not grant permission to download any copyrighted content.MP3/WMA/JPEG file informationLimitations on MP3/WMA/JPEG file playback•MP3/WMA/JPEG file is the disc/card that is standardized by ISO9660, its file name must include 3-digits extensionletters, “mp3”, “wma”, “jpg”.•MP3/WMA/JPEG file must be correspond to the ISO standardized files.•This unit can read 600 files per disc/card. If one directory has more than 600 files, it reads up to 600 files, theremaining files will be omitted.•The unit is able to recognize up to a maximum of 50 directories per disc/card.•MP3/WMA/JPEG files cannot be used for the purpose of recording.•If the disc/card has both audio tracks and MP3/WMA/JPEG files, only audio tracks are played.•It may take more than one minute for this unit to read MP3/WMA/JPEG files depending on its structure.•Music recorded by “Joliet Recording Specification” can be played back, the file name is displayed (within 16letters) on the screen. Long file names will be condensed.•The music files recorded by “Hierarchical File System” (HFS) cannot be played.Limitations on display•The maximum number for display is 16 letters.Available letters for display are the following:capital or small alphabets of A through Z, numbers of 0 through 9, and _ (under score).•Other letters than those above are replaced in hyphen.Notes on MP3/WMA/JPEG filesTo play back MP3/WMA/JPEG file in the recorded order,1. Use MP3/WMA/JPEG software that records data alphabetically or numerically.2. Name each file including two-digit or three-digit number (ex. “01” “02” or “001” “002”).3. Refrain from making too many sub-folders.CAUTION:•Some MP3/WMA/JPEG CDs/Cards cannot be played back depending on the recording conditions.•The CDs/Cards that has no music data or non MP3/WMA/JPEG files cannot be played back.Standard, sampling frequency, and the bit rate:MP3 CDMPEG-1 Audio32kHz, 44.1kHz, 48kHz32kbps ~ 320kbps (constant bit rate or variable bit rate)The recommend recording setting for a high-quality sound is 44.1kHz of sampling frequency and 128kbps ofconstant bit rate.WMA CDWMA version 7, and 832kHz, 48kbps44.1kHz, 48kbps ~ 192kbps48kHz, 128kbps ~ 192kbpsThe file recorded by mono, 48kHz, 48 kbps is not available to this unit.Microsoft, Windows Media, and Windows Logo are trademarks or registered trademarks of Microsoft Corporation in both theUnited States and other countries. 2F90201A (E)p53-58 4/4/05, 9:03 PM55
56Advanced playback (DVD)MP3/WMA/JPEG operation (continued)Press CCCCC/DDDDD/BBBBB/AAAAAor Number buttons (0–9) to se-lect the desired file.• In case the folder includes more than 15 files, press BBBBBor AAAAA to display next file list.• When PLAY has been pressed after displaying the filemenu, or when the disc tray has been closed usingPLAY, playback begins automatically starting from thefirst file. In this case, if the first file is an MP3/WMA file,only MP3/WMA files are played back in order. If thefirst file is a JPEG file, the first JPEG file is played back.MP3/WMA CD playbackCDENTER▲/▼//STOP0–9Place a CD-R/RW on which MP3 or WMA fileshave been recorded onto the disc tray, or inserta Media card on which MP3 or WMA files havebeen recorded into the appropriate media cardslot on the front panel.Note: When the Media card is inserted, the unit ischanged to the CARD mode automatically.1Press DVD/CARD to select the DVD (CD) mode orthe CARD mode.A file menu screen will appear on the screen.Press BBBBB/AAAAA or ENTER to select folder.23Press ENTER.The selected file starts playing back.4Press STOP to end playback.• The unit records the stopped point. “ ” appears onthe screen. Press PLAY to resume playback (from thescene point).• If you press STOP again, unload the disc or changethe DVD mode and the CARD mode, the unit will clearthe stopped point.About file menuNotes:• The picture menu is displayed when the FUJICOLOR CDor the Kodak Picture CD are played. To display the filemenu, press TOP MENU.• In the case of a CD containing a mixture of MP3, WMA andJPEG files, the files are played back by selecting them fromthe file menu.• MP3 or WMA file on the Kodak Picture CD is not recog-nized on this unit.5PLAYTOP MENUDVD/CARDCARDCAUTIONDo not insert any foreign objects into the Media card slot as thiscan result in a risk of fire or electric shock.Place a CD-R/RW on which MP3, WMA or JPEG files havebeen recorded onto the disc tray or insert a Media card onwhich MP3, WMA or JPEG files have been recorded intothe media card slot on the front panel.Notes:• During MP3/WMA/JPEG-Playback, you cannot use SEARCH,A-B Repeat functions.• You can use Repeat (Track or All), Random functions andProgram playback for MP3/WMA/JPEG Playback 51.• When the Media card is inserted into the both card slots, theupper card slot is read. If you want to playback theCompactFlash memory card in the lower card slot, eject theMedia card from the upper card slot.To eject the Media cardConfirm the Media card is not in use now. Pull the card outslowly and straight.Note:Do not remove the card while it is in use. If removed while inuse, information on the card may be lost. 2F90201A (E)p53-58 4/4/05, 9:03 PM56
57Advanced playback (DVD)TOP MENUMENU▲/▼//ENTER0–9The slide show enables you to view pictures (files) one afteranother automatically.Preparation:Set “JPEG Interval” setting to “5 Seconds”, “10 Seconds”or “15 Seconds” .Place a CD-R/RW on which JPEG files have beenrecorded onto the disc tray, or insert a Media cardon which JPEG files have been recorded into theappropriate media card slot on the front panel.Note: When the Media card is inserted, the unit ischanged to the CARD mode automatically.1Press DVD/CARD to select the DVD (CD) mode orthe CARD mode. file menu screen will appear onthe screen. Press B/A to select folder.2Press CCCCC/DDDDD/BBBBB/AAAAAor Number buttons (0–9) to se-lect the desired file.To display a picture menu, press MENU.(To return to a file menu, press TOP MENU.)Press B/A or C/D to select the desired file.3Press ENTER. The selected picture appears onthe screen.Rotating an imageYou can rotate an image by 90 degrees by pressingANGLE during playback of the image.“”, “ ”, “ ” or “ ” appears brieflyon the screen.Press STOP to end playback.The file menu appears on the screen.If you want to watch the other file, repeat steps3 ~ 4.5JPEG playbackSelect your desired starting file for the slideshow in the step 4 as left.2Press ENTER to start slide show from the se-lected file.•If you press PAUSE during the slide show, the slideshow stops temporary. “ 4” appears briefly on the pic-ture.If the picture appears upside down or sideways, pressANGLE repeatedly until it’s right side up.“”, “ ”, “ ” or “ ” appears brieflyon the screen.Press PLAY or SKIP again to resume the slide show.•When the slide show playback finished the file list ap-pears.•To stop the slide show, press STOP. The file list ap-pears.JPEG slide show1• To display next list, press SKIP / .• When PLAY has been pressed after displayingthe file menu, or when the disc tray has beenclosed after pressing PLAY, playback begins au-tomatically starting from the first file. In this case,if the first file is a JPEG file, the first JPEG file isplayed back. If the first file is an MP3/WMA file,only MP3/WMA files are played back in order.ANGLEPLAYSTOPSKIP/PAUSE4DVD/CARDCAUTIONDo not insert any foreign objects into the Media card slot as this can result ina risk of fire or electric shock.CDCARDCDCARDTo eject the Media cardConfirm the Media card is not in use now. Pull the card outslowly and straight.Notes:• Do not remove the card while it is in use. If removed while inuse, information on the card may be lost.• If the DVD video player is connected to a HDTV usingHDMI, you can display the HD resolution JPEG images(720p or 1080i). See “HD Jpeg” on page 62.• When the Media card is inserted into the both card slots, theupper card slot is read. If you want to playback theCompactFlash memory card in the lower card slot, eject theMedia card from the upper card slot. 2F90201A (E)p53-58 4/4/05, 9:03 PM57
58Setting procedurePress SETUP during stop mode.The following on-screen displayappears.123To make SETUP screen disappear, pressSETUP or RETURN.5Customizing the function settingsYou can change the default settings to customize performanceto your preference.ENTERC/D/B/A•Repeat steps 3 and 4 to changeother settings.•To select another operation, goback to step 2 by pressing Crepeatedly.Function setup (DVD)Press Bor Ato select the desired section, thenpress D or ENTER.Press Cor D to select the desired option.4Change the selection using B or A, by referringto the corresponding pages 60~63.SETUPDVDVCDCD/Enter/Setup/ReturnRETURN 2F90201A (E)p53-58 4/4/05, 9:03 PM58
59Function setup (DVD)Section OptionMenuSubtitleAudioE.B.L.TV ScreenDisplayPicture ModeJPEG IntervalDialogueQSoundDigital OutPasswordParentalSelect FilesHD JpegOutputDetailsTo select the language of “Menu”, “Subtitle” and“Audio” if more than one language are available onthe disc.To select On or Off for E.B.L. (Enhanced BlackLevel).To select a picture size according to the aspectratio of your TV.To turn on or de-activate the operational status dis-play on the screen.To select a preferred picture mode from “Video”,“Film” or “Auto”.To select a preferred setting for the slide show play-back.To select On or Off for DRC (Dynamic Range Con-trol).To select On or Off for QSound.To select an output sound format corresponding toyour system connection.Input 4-digit password to set the parental level.To select a preferred parental level for the parentalsetting.To select a preferred file type for playing back a CDcontaining a mixture of file types.To select On or Off for HD Jpeg.To select a preferred video output signal from “Pro-gressive” or “Interlace”.Page6060606061616161616262626262Customizing the function settings (continued)Setting details 2F90201A (E)p59-63 4/4/05, 9:03 PM59
60Function setup (DVD)Customizing the function settings (continued)Menu, Subtitle, AudioYou can select the language of “Menu”, “Subtitle” and“Audio” if more than one languages are recorded ontothe disc.English, Francais, Espanol:The selected language will be heard or seen.Other:Other language can be selected (see the“Language code list” ).Original: (Audio)The unit will select the first priority language ofeach disc.Off: (Subtitle)Subtitles do not appear.Notes:• If the selected language is not recorded on the disc, thefirst-priority language is selected.• If you want to change the OSD language, you can performit by VCR MENU .E.B.L.To select the black level of playback pictures, set yourpreference and monitor’s ability.On: Enhanced grey scale (0 IRE cut off)Off: Standard grey scale (7.5 IRE cut off)TV ScreenYou have the following screen sizes to choose from:4:3 (Letter box):Select this mode when connecting to a conven-tional TV. When playing back a wide screen-DVDdisc, it displays the wide picture with black bandsat the top and bottom of screen.4:3 (Pan scan):It displays the wide picture on the whole screenwith left and right edges automatically cut off.16:9 (Wide):Select this mode when connecting to a wide-screen TV. A wide screen picture is displayed fullsize.Press OPEN/CLOSE to view in the selected screen size.Note:If the DVD disc is not formatted in the pan & scan style, itdisplays 4:3 style.DisplayOn screen display can be switched on or off when youpress the buttons.On: On screen displays appear when you pressthe buttons (factory setting).Off: On screen displays do not appear when youpress any buttons.Setting details 2F90201A (E)p59-63 4/4/05, 9:03 PM60
61Function setup (DVD)JPEG IntervalYou can continuously play back all JPEG files automati-cally.After the setting below, start playing the disc on whichJPEG files have been recorded.Off:Plays back one file at a time.5 Seconds:Plays back images in the form of a slide show at5 second intervals.10 Seconds:Plays back images in the form of a slide show at10 second intervals.15 Seconds:Plays back images in the form of a slide show in15 second intervals.Picture ModeThere are two types of source content in picturesrecorded in DVD video discs: film content (picturesrecorded from films at 24 frames per second) andvideo content (video signals recorded at 30 frames persecond). Make this selection according to the type ofcontent being viewed.Auto: Select this position normally.The DVD player automatically detectssource content, film or video, ofplayback source, and converts thatsignal in the progressive output formatin an appropriate method.Film: The DVD player converts film contentpictures in the progressive outputformat appropriately. Suitable forplayback of film content pictures. Theprogressive output feature will be mosteffective under this selection.Video: The DVD player filters video signal,and converts it in the progressiveoutput format appropriately.Suitable for playback of video contentpictures.Note:Depending on the disc, pictures may be cut off ordoubled. In this case, select “Video”.QSoundThis DVD video player equipped with a “QSound”. It canproduce the effect of being in a cinema or a concert hall.On: The QSound operates.Off: The QSound is disengaged.On: DRC (TV):Loud sound such as explosion or similar is toneddown slightly when played back. This makes itsuitable for when it is connected to a stereo.Off: DRC (Std):It plays back at the recording level on the disc.Notes:• This function works only during playback of Dolby Digitalrecorded discs.• The level of Dynamic Range Reduction may differdepending on DVD video disc.DialogueDRC (Dynamic Range Control) enables you to controlthe dynamic range so as to achieve a suitable sound foryour equipment.Note:The QSound setting can also be changed with AUDIO onthe remote control .Digital OutSelected the output sound format corresponding to yoursystem connection.PCM:Select when connected to a 2 channel digitalstereo amplifier.Raw:Disc audio raw data will be output.Notes:•When you make a connection to a TV, or DolbySurround Pro Logic or stereo system via the analogaudio jacks, select “PCM” or “Raw”.•If apply HDMI connection to TV, make sure to select“PCM”, audio signal passing to TV via HDMI cable. 2F90201A (E)p59-63 4/4/05, 9:03 PM61
62Function setup (DVD)Customizing the function settings (continued)PasswordParentalSelect FilesHD JpegOffAllOffOutput Interlace/0-9/Enter/Clear/Setup/Return----To change the parental level1) Press C or D to select “Password”.2) Press Number buttons (0–9) to enter the passwordyou have stored.3) Press ENTER.• The rating is now unlocked.4) Press C or D to select “Parental”, then press B orAto change the parental level.5) Press C or D to select “Password”, then pressNumber buttons (0–9) to enter the password.Note: You can change the password if you want.6) Press ENTER.Now the parental level is changed and locked. Parental control settingSome discs are specified not suitable for children.Such discs can be limited not to play back with theunit.1) Press C or D to select “Parental”, then press B orA until the level you require appears.•Level Off: The parental control setting does notfunction.•Level 8: Virtually all DVD software can beplayed back.•Level 1: DVD software for adults cannot beplayed back.Select from the level 1 to level 8. The limitation willbe more severe as the level number is lower.2) Press C or D to select “Password”.Press Number buttons (0–9) to input a 4-digitpassword. Be sure to remember this number!•If you input a wrong number, press CLEAR.3) Press ENTER to store the password.Note: Now the rating is locked and the setting cannotbe changed unless you enter the correct password.4) Press OPEN/CLOSE to activate Parental controlsetting. (See “Temporary disabling of rating level byDVD disc” on page 64.)Notes:• Depending on the discs, the unit cannot limit playback.• Some discs may not be encoded with specific ratinglevel information though its disc jacket says “adult.” Forthose discs, the age restriction will not work.Select FilesWhen playing back a CD or Media card containing amixture of MP3, WMA and JPEG files, only MP3/WMAor JPEG files can be displayed on the file menu.All:Displays all files.Music Only:Displays only MP3/WMA files.Pictures Only:Displays only JPEG files.If you forget the password...1. Press OPEN/CLOSE to open the disc tray.2. Remove the disc.3. Press OPEN/CLOSE again to close the disc tray.“No Disc” appears on the screen.4. While holding 7 down on the remote control, pressSTOP on the front panel. “PASSWORD CLEAR”appears on the screen.5. Enter a new password again.HD JpegThis DVD video player equipped with a “HD Jpeg”. It candisplay the HD resolution JPEG images when the DVDvideo player is connected to a HDTV using HDMI.On:Select when you connect the DVD video player toa HDTV via HDMI OUT jack. JPEG images is dis-played in suitable picture quality (480p, 720p or1080i) .Off:The picture processing quality is fixed to 480p.Notes:• When the DVD video player is not connected to a TVusing HDMI, you cannot select “On”.• When HD Jpeg is set to “On”, zoom function is prohibitedand component video outputs disabled when 720p or1080i is selected.Setting details 2F90201A (E)p59-63 4/4/05, 9:03 PM62
63Function setup (DVD)OutputYou can select the video output signal of the DVDvideo player to the TV from “Interlace” or “Progressive”.1) Press C or D to select “Output”.2) Press A, then press C or D to select “Interlace” or“Progressive”.Interlace:Select when connecting to a composite TV or a TVequipped with component video inputs butprogressive scan is not compatible.Progressive:Select when connecting to a TV equipped withcomponent video inputs, progressive scancompatible.3) Press ENTER.Warning:Once “Progressive” is selected when connecting to aTV progressive scan incompatible, no image will beseen on the video display.In this case, you must reset the unit by pressing STOPon the front panel for five seconds. The video outputwill be restored to “Interlace” setting, and a picture willonce again be seen on a conventional analog display.Notes:• Some discs may not be played back with the progressivescanning mode correctly because of the disc characteris-tics or recording condition.• Once Progressive scan on, the VIDEO (yellow) and S-VIDEO outputs are disabled.Note:If each setup (pages 60~63) has been completed, the unitcan always be worked under the same conditions(especially with DVD discs).Each setup will be retained in the memory even if youturn the power off. 2F90201A (E)p59-63 4/4/05, 9:03 PM63
64Temporary disabling of rating level by DVD discDepending on the DVD disc, the disc may try to temporarily cancel the ratinglevel that you have set.It is up to you to decide whether to cancel the rating level or not.Load a DVD disc and press PLAY or OPEN/CLOSE on the unit .Note:This temporary cancellation of rating level will be kept until thedisc is ejected.When the disc is ejected, the original rating level will be set againautomatically.1Playback will commence if the entered pass-word was correct.42Your disc exceedsthe parental control level#.Parental Control LevelCancel Picture/Enter/Return35ENTER▲/▼RETURNPLAY0–9OPEN/CLOSEIf the DVD disc has been designed to temporarilycancel the Rating level, the screen which followsthe “Reading Disc” screen will change, dependingon which disc is played. If you select “YES” withthe ENTER key, “Your disc exceeds the parentalcontrol level#.” screen will then appear.If you wish to cancel the set rating level tempo-rarily, select “Parental Control Level” with C C C C C orDDDDD, then press ENTER. If the 4-digit password atstep 2 on page 62 has been set, the passwordentering screen will appear as shown in step 4.Alternatively, if the password has not been set,playback will commence. If you don’t know (orhave forgotten) the password, select “CancelPicture”.The setting screen will disappear. Press OPEN/CLOSE to remove the disc.Enter the password with Number buttons (0–9).Then press ENTER.To exit from the entry, press RETURN.Function setup (DVD) 2F90201A (E)p64-69 4/4/05, 9:03 PM64
65OthersLanguage code listEnter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” .Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925Amharic 1123 Galician 1722 Malay 2329 Spanish 1529Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931Armenian 1835 German 1415 Maltese 2330 Swahili 2933Assamese 1129 Greek 1522 Maori 2319 Swedish 2932Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121Chinese 3618 Javanese 2033Rhaeto-Romance2823 Urdu 3128Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631Language Name Code Language Name Code Language Name Code Language Name CodeOthers 2F90201A (E)p64-69 4/4/05, 9:03 PM65
66OthersMulti brand remote controlThe remote control can be compatible with various brands of TV/Cable box/DSS® satellite receiver by setting their control codes. TheTOSHIBA code has initially been set to control TOSHIBA TVs.Setting TV control codes Table of TV brand codesBrand name Brand Codeof your TVToshiba 01Bell & Howell 09Carver 10Celebrity 03Citizen 12Curtis Mathes 09, 12Dumont 14Electro band 03Emerson 09,11Fisher 09GE 02, 07, 11Gibralter 14Goldstar 11Hallmark 11Hitachi 06Infinity 10JBL 10JCB 03JVC 05LXI01, 02, 09, 10, 11Magnavox 10Marantz 10Megatron 06, 11Memorex 04, 09, 11MGA 04, 11Midland 02,07, 14Mitsubishi 04, 11Motorola 08MTC 12NAD 01, 11Nikko 11Optimus 09Optonica 08Panasonic 07, 10, 15Press TV to set the remote control operatingyour TV.12ImportantSome TV’s may not respond to all the operations left, ormay not be operated at all with this remote control. Inthis case, operate your TV with its own remote control.Notes:• For some brands, several control codes (brand codes) are al-located. Try each of them until the buttons work on your TV.• If you replace the remote control’s batteries, set the brand codeagain.While holding down PROGRAM enter the twodigits of your TV's brand code (listed below)using Number buttons (0–9), then releasePROGRAM.Point the remote control at your TV and use eachbutton listed below to make sure that your TV isoperated correctly.POWER To turn the TV on or off.CH MMMMM/?????To select TV channels in the upperor lower direction.VOL +/– To adjust the sound level.INPUT SELECT To select an external source suchas a VCR.Number buttons To select TV channels. When select-ing channels 1 to 9, first enter 0 andthen desired number.100 To substitute for 100 channel key.DISPLAY To turn on or off TV’s screen dis-play.ENTER To use for the TV’s ENTER key. (0–9)Brand name Brand Codeof your TVPenney01, 02, 07, 11, 12Philco 10Philips 10Pioneer 16Princeclub 12Prism 07Proscan 02Proton 11Pulser 14Quasar 07, 15Radio Shack 13RCA 02Realistic 09, 11, 13Runco(NEC) 14Samsung 11, 12Sanyo 09Scotch 11Scott 11Sears01, 02, 09, 10, 11Sharp 08, 13Sony 03Soundesign 11Supreme 03Sylvania 10Tandy 08Technics 07, 15Techwood 07Teknika 04,10,12TMK 11Victor 05Vidikron 10Vidtech 11Wards 10, 11,13Zenith 14ENTERPROGRAMPOWERCH MMMMM/?????0–9TV100INPUT SELECTVOL +/–DISPLAY 2F90201A (E)p64-69 4/4/05, 9:04 PM66
67OthersTable of Cable box brand codesSetting Cable box/DSS® satellitereceiver control codesPress CABLE BOX to set the remote controloperating your Cable box/DSS® satellite receiver.12ImportantSomeCable box/DSS®satellite receivermay not respondto all the operations left, or may not be operated at allwith this remote control. In this case, operate them withits own remote control.Notes:• For some brands, several control codes (brand codes) are al-located. Try each of them until the buttons work on your Cablebox/DSS® satellite receiver.• If you replace the remote control’s batteries, set the brand codeagain.While holding down PROGRAM enter the twodigits of your Cable box/DSS®satellite receiverbrand code (listed below) using Number buttons(0–9), then release PROGRAM.Point the remote control at your Cable box/DSS®satellite receiver and use each button listed below tomake sure that your Cable box/DSS®satellite receiveris operated correctly.POWER To turn the Cable box/DSS®satel-lite receiver on or off.CH MMMMM/?????To select cable/satellite channels inthe upper or lower direction. (Notapplicable to some brands of cablebos/satellite receiver.)Number buttons (0–9)To select desired channels to record.ENTERTo use for the Cable box’s ENTER key.(Some cable boxes require you to use 100 button as theenter button.)Brand name of Brand Codeyour cable boxToshiba 36Anvision 13, 20, 21,22, 23, 24,25, 26, 58,62, 84Archer 1, 20, 21,29, 42, 44,63, 88, 91Cablestar 13, 20, 21,22, 23, 24,25, 26, 58,62, 84Cableview 30, 42, 44,52, 63, 88Citizen 30, 42, 44,52, 63, 88Curtis 8, 9, 56, 61Diamond 1, 20, 21,29, 42, 44,63, 88, 91Eagle 13, 20, 21,22, 23, 24,25, 26, 58,62, 84Eastern 26, 28GC Brand 30, 42, 44,52, 63, 88Gemini 4, 30, 85General 1, 2, 3,4, 31, 34,55, 83, 85,91Hamlin 14, 15, 28,41Hitachi 31, 79, 80Jerrold 1, 2, 3,4, 31, 34,55, 85, 91Macom 31, 79, 80Magnavox 13, 20, 21,22, 23, 24,25, 26, 58,62, 84Movietime 29, 32, 38,39, 42, 44,88NSC 29, 32, 38,39, 42, 44,88OAK 10, 11, 12,13, 46OAK Sigma 10, 11, 12,13, 46Panasonic 6, 8, 16, 17Brand name of Brand Codeyour cable boxPhilips 4, 13, 20,21, 22, 23,24, 25, 26,58, 62, 84Pioneer 5, 6, 78Pulsar 30, 42, 44,52, 63, 88Randtek 13, 20, 21,22, 23, 24,25, 26, 58,62, 84RCA 6, 8, 16, 17Realistic 44, 88Regal 14, 23, 41,84Regency 26, 28Rembrandt 29, 32, 38,39, 42, 44,88Samsung 4, 6, 32,42, 78Scientific Atlanta8, 9, 56, 61Sheritech 27SL Mark 4, 6, 32,42, 78Sprucher 6, 8, 16, 17Stargate 4, 6, 30, 32,42, 44, 52,63, 78, 88Sylvania 19Teknika 74Telecaption 77Teleview 4, 6, 32,42, 78Texscan 18, 19Tocom 1, 33, 34,42, 48, 49,73, 91Unica 1, 20, 21,29, 42, 44,63, 88, 91Universal 29, 42, 43,44, 52, 63,82, 88Videoway 7, 23, 45,50, 84Viewstar 13, 20, 21,22, 23, 24,25, 26, 58,62, 84Warner Amex6Zenith 7, 23, 45,50, 84InstrumentBrand name Brand codeToshiba 99RCA 98Sony 97Magnavox 95, 96Brand name Brand codeDraker 94Primestar 93Hitachi 92, 89Panasonic 90Table of DSS® satellite receiver brand codes 2F90201A (E)p64-69 4/4/05, 9:04 PM67
68OthersTroubleshootingBefore calling a service technician, please check the following table for a possible cause of the symptoms and some solutions.Symptoms Solutions• Make sure the power cord is plugged in.• Try another AC outlet.• Unplug unit, then plug it back in.• Select the DVD or VCR mode before operating.DVD/VCR does not operate.DVD/VCRPage5–533,45The remote control does not function.• Make sure the DVD/VCR•TV•CABLE BOX mode is set properly.• Aim the remote control at the remote sensor.• Operate within Approx. 7 Meters or reduce the light in the room.• Clear the path of the beam.• The batteries are weak. Replace the batteries.• Check the batteries are inserted correctly.15DVDNo picture.• Antenna connection is not correct or antenna cable is disconnected.• The video channel is not in the correct position or the TV is not set to the videochannel 3 or 4.• Check the unit is connected correctly.• The video input selector of the TV is not set to VIDEO. Set to VIDEO (orequivalent).• Channel is set to the external mode.No sound.• Check the unit is connected correctly.• Check the input selector of the amplifier is set properly.• The unit is in the Special playback mode.16~192516~22––16~22–34,47• Select proper language in the menu options.Display is not shown in your language. 60Playback doesn’t start.• No disc is inserted.• The disc may be dirty. Clean up the disc.• The unit cannot play DVD-ROMs, etc.Stopping playback, slow-motion play, repeatplay, or memory play, etc. cannot beperformed.• Some discs may not do some of the functions.45810–No Cable TV reception. • Check all Cable TV connections.• Station or Cable TV system problems, try another station. 18~19Noise bars on screen.• Tracking adjustment beyond range of automatic tracking circuit. Try Manualtracking adjustment.• Video heads are dirty.• The tape is worn or damaged.VCR• The erase prevention tab of the video cassette is broken off.• The unit is in the external input mode.TV recording does not work. 32,37Timer recording does not work.• The time is not set correctly.• The recording start/end time is not set correctly.• The TIMER REC has not been pressed ( is not lit).2740403434–No picture, or the screen is blurred or dividedinto two parts.• The PROGRESSIVE scan is “On” although the unit is connected to a TV via theVIDEO OUT or the S-VIDEO OUT jack. 63No subtitle. • Some discs have no subtitles.• Subtitles are cleared. Press SUBTITLE.Angle cannot be changed. • Multi-angles are not recorded on the DVD disc.• The function is prohibited with the unit or the disc. appears on the screen.545247No 4:3 (16:9) picture. • The setup does not match your TV.No on-screen display. • Select Display “On”.6060No surround sound. • The setup does not match your stereo system.The unit or remote operation key is notfunctioning. • Turn off the unit and unplug the AC power cord for several minutes, then replug it.23,24Playback does not start when the title isselected. • Check the Parental setup.Audio soundtrack and/or subtitle languageis not changed when you play back a DVD. • Multilingual language is not recorded on the DVD disc.–62,6453,54 2F90201A (E)p64-69 4/4/05, 9:04 PM68
69OthersSpecificationsAC 120 V 60 HzOperation: 20 W, Stand by: 2 W7.7 lbs (3.5 kg)Width: 16-15/16 inches (430 mm)Height: 3-1/2 inches (89.5 mm)Depth: 9-1/16 inches (230 mm)181 channel freq. synthesizedVHF 2-13UHF 14-69Cable TV 113 ChannelsUHF/VHF 75 1coaxialChannel 3 or 4, SwitchableNTSC4 Rotary headsHi-Fi sound - 2 Tracks / MONO sound - 1 Track20 Hz to 20,000 HzMore than 90dBApprox. 1 minute and 48 seconds (with T-120 Cassette Tape)DVD (12 cm, 8 cm), CD (12 cm, 8 cm)DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz90dB (DVD)0.02% (DVD)Less than 0.01% WrmsTemperature: 5˚C-40˚C (41˚F-104˚F), Operating status: HorizontalPower supplyPower consumptionWeightDimensionsTunerAntenna input/outputRF channel outputColor systemVideo headAudio trackHi-Fi frequency responseHi-Fi dynamic rangeFF/REW time at 25˚C (77˚F)Applicable discFrequency rangeS/N ratioHarmonic distortionWow and flutterOperating conditionsGeneralInput/OutputDVD/VCRVideo input 1.0 V (p-p), 75 1, negative sync., pin jack x 2Video output 1.0 V (p-p), 75 1, negative sync., pin jack x 1Audio input –8 dBm, 50 k1, negative sync., pin jack (L/R) x 2Audio output –8 dBm, 1 k1, negative sync., pin jack (L/R) x 1DVDS-video output (Y) 1.0 V (p-p), 75 1, negative sync., Mini DIN 4-pin x 1(C) 0.286 V (p-p), 75 1Component video output (Y) 1.0 V (p-p), 75 1, negative sync., pin jack x 1(PB)/(PR) 0.7 V (p-p), 75 1, pin jack x 2Audio output (DIGITAL COAXIAL) 0.5 V (p-p), 75 1, pin jack x 1Audio output (DIGITAL OPTICAL) Optical connector x 1Audio output (ANALOG) –12 dBm, 1 k1, pin jacks (L, R) x 1Supplied accessoriesAudio/video cable ................................................. 1Remote control (SE-R0172) ................................. 1Batteries (AAA) ..................................................... 275 1 coaxial cable ................................................ 1HDMI cable ........................................................... 1•This model complies with the above specifications.• Designs and specifications are subject to change without notice.•This model may not be compatible with features and/or specifications that may be added in the future. 2F90201A (E)p64-69 4/4/05, 9:04 PM69
70OthersLimited warrantyLimited United States WarrantyDVD/VCR Combinations - Exchange WarrantyToshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to originalconsumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMERPURCHASER OR ANY PERSON RECEIVING THIS DVD/VCR COMBINATION AS A GIFT FROM THEORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.PRODUCTS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE U.S.A., INCLUD-ING, WITHOUT LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.PRODUCTS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT LIMITATION,CANADA AND MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE WARRANTIES.Limited Ninety (90) Day WarrantyTACP warrants this DVD/VCR Combination and itsparts against defects in materials or workmanship forperiod of ninety (90) days after the date of original retailpurchase. DURING THE FIRST NINETY (90) DAYSAFTER THE DATE OF ORIGINAL RETAILPURCHASE, TACP WILL EXCHANGE A DEFECTIVEDVD/VCR COMBINATION WITH A NEW ORREFURBISHED DVD/VCR COMBINATION WITHOUTCHARGE TO YOU. YOU MUST CONTACT TACP'SCONSUMER SOLUTIONS CENTER FOR INSTRUC-TIONS ON HOW TO PROCESS YOUR IN WAR-RANTY EXCHANGE REQUEST. THE CONSUMER ISRESPONSIBLE FOR ALL INBOUND TRANSPORTA-TION AND INSURANCE CHARGES FOR THE DVD/VCR COMBINATION TO THE EXCHANGE CENTER.DURING THE PERIOD THAT COMMENCES ON THEDATE THAT IS NINETY ONE (91) DAYS AFTER THEDATE OF ORIGINAL RETAIL PURCHASE ANDBEYOND, TACP WILL EXCHANGE A DEFECTIVEDVD/VCR COMBINATION WITH A NEW ORREFURBISHED DVD/VCR COMBINATION FOR ANOMINAL FEE. YOU MUST CONTACT TACP'SCONSUMER SOLUTIONS CENTER FORINSTRUCTIONS ON HOW TO PROCESS YOUREXCHANGE REQUEST. THE CONSUMER ISRESPONSIBLE FOR ALL INBOUND TRANSPORTA-TION AND INSURANCE CHARGES FOR THE DVD/VCR COMBINATION TO THE EXCHANGE CENTER.* Rental UnitsThe warranty for rental units begins with the first rentalor thirty (30) days after the date of shipment to therental firm, whichever comes first.* Commercial UnitsDVD/VDR Combinations sold and used for commercialpurposes have a limited ninety (90) day warranty for allparts and labor.Owner's Manual and Product Registration CardRead this owner’s manual thoroughly before operat-ing this DVD/VCR Combination. Complete and mailthe enclosed product registration card or registeryour product on-line at www.tacp.toshiba.com/service as soon as possible. By registering yourDVD/VCR Combination you will enable TACP tobring you new products specifically designed to meetyour needs and help us to contact you in the unlikelyevent that a safety notification is required under theConsumer Product Safety Act. Failure to completeand return the product registration card does notdiminish your warranty rights.Your ResponsibilityTHE ABOVE WARRANTIES ARE SUBJECT TOTHE FOLLOWING CONDITIONS:(1) You must retain your bill of sale or provide otherproof of purchase.(2) All warranty servicing of this product must bemade by an Authorized TACP Service Station.(3) The warranties from TACP are effective only ifthe product is purchased and operated in theContinental U.S.A. or Puerto Rico.(4)Labor service charges for set installation, setup,adjustment of customer controls and installation orrepair of antenna systems are not covered by thiswarranty. Reception problems caused byinadequate antenna systems are your responsibility.(5)Warranties extend only to defects in materials orworkmanship as limited above, and do not extendto any DVD/VCR Combination or parts that havebeen lost or discarded by you or to damage to theDVD/VCR Combination or parts caused by fires,misuse, accident, Acts of God (such as lightningor fluctuations in electric power), improperinstallation, improper maintenance, or use inviolation of instructions furnished by TACP; use ormalfunction through simultaneous use of thisproduct and connected equipment; or to units thathave been modified or had the serial numberremoved, altered, defaced, or rendered illegible. 2F90201A (E)p70-BACK 4/4/05, 9:04 PM70
71OthersHow to Obtain Warranty ServicesIf, after following all of the operating instructions in thismanual and checking the section “Troubleshooting,”you fund that service is needed:(1) For instructions on how to obtain warranty servicefor exchange program DVD/VCR Combinations,contact TACP's Call Center toll free at 1-866-583-7353.(2) You must include the original bill of sale (or a copyof the original bill of sale) or other proof of pur-chase along with the entire DVD/VCR Combinationwhen sending the DVD/VCR Combination to theAuthorized TACP Service Station specified byTACP's Call Center. You must pay for alltransportation and insurance charges for the DVD/VCR Combination to and from the AuthorizedTACP Service Station.For additional information, visit TACP's website:www.tacp.toshiba.comALL WARRANTIES IMPLIED BY THE LAW OF ANYSTATE OF THE U.S.A., INCLUDING THE IMPLIEDWARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE, AREEXPRESSLY LIMITED TO THE DURATION OF THELIMITED WARRANTIES SET FORTH ABOVE. WITHTHE EXCEPTION OF ANY WARRANTIES IMPLIEDBY THE LAW OF ANY STATE OF THE U.S.A. ASHEREBY LIMITED, THE FOREGOING WARRANTYIS EXCLUSIVE AND IN LIEU OF ALL OTHERWARRANTIES, GUARANTEES, AGREEMENTS,AND SIMILAR OBLIGATIONS OF TACP WITHRESPECT TO THE REPAIR OR REPLACEMENT OFANY PARTS. IN NO EVENT SHALL TACP BELIABLE FOR CONSEQUENTIAL OR INCIDENTALDAMAGES (INCLUDING, BUT NOT LIMITED TO,LOST PROFITS, BUSINESS INTERRUPTION, ORMODIFICATION OR ERASURE OF RECORDEDDATA CAUSED BY USE, MISUSE OR INABILITY TOUSE THIS PRODUCT).No person, agent, distributor, dealer or company isauthorized to change, modify or extend the terms ofthese warranties in any manner whatsoever. The timewithin which an action must be commenced to enforceany obligation of TACP arising under the warranty orunder any statute, or law of the United States or anystate thereof, is hereby limited to ninety (90) days fromthe date you discover or should have discovered, thedefect. This limitation does not apply to impliedwarranties arising under state law.THIS WARRANTY GIVES YOU SPECIFIC LEGALRIGHTS AND YOU MAY ALSO HAVE OTHERRIGHTS WHICH MAY VARY FROM STATE TOSTATE IN THE U.S.A. SOME STATES OF THEU.S.A. DO NOT ALLOW LIMITATIONS ON HOWLONG AN IMPLIED WARRANTY LASTS, WHEN ANACTION MAY BE BROUGHT, OR THE EXCLUSIONOR LIMITATION OF INCIDENTAL OR CONSEQUEN-TIAL DAMAGES, SO THE ABOVE PROVISIONSMAY NOT APPLY TO YOU UNDER SUCH CIRCUM-STANCES. 2F90201A (E)p70-BACK 4/4/05, 9:04 PM71
Printed in ThailandColorStream and ColorStream Pro are registered trademarks of Toshiba America Consumer Products, L.L.C. 2F90201A (E)p70-BACK 4/4/05, 9:04 PM72

Navigation menu