Omron Okayama factory WE70CL FA Wireless LAN Unit - Client User Manual

Omron Corporation Okayama factory FA Wireless LAN Unit - Client Users Manual

Contents

Users Manual Part 2

Contact AddressOMRON ELECTRONICS LLC.After sales SupportEngineering Service DepartmentOne Commerce Drive, Schaumburg. IL 60173-5302 U.S.APhone: 1-847-843-7900Fax: 1-847-843-7787OMRON ELECTRONICS B.V.Wegalaan 61 2132 JD, HOOFDDORP,THE NETHERLANDSPhone: 31-23-56-81-100Fax: 31-23-56-81-188(1) Configure an IP address and a subnet mask for PC.(2) Start a WWW browser.(3) Enter the IP address specified for the wireless unit in the address bar of the WWW browser.  Enter http://192.168.0.1/ (factory shipment) for WE70-AP and http://192.168.0.254/ (factory shipment) for WE70-CL, then press [Enter] key.(4) In case of an access point, a password input is requested. Press [Enter] key while leaving the password field blank.(5) A Basic Setup screen of Network Setup menu is displayed at first. *  To configure SSID and encryption of wireless LAN from PC connected to a wired LAN, See "WE70 AP/CL FA Wireless LAN Unit OPERATION MANUAL" (Cat.No.N153-E1).■ Initiating Setup Screen■ Channel assignment based on frequency band802.11b/g: All of 13 channels (except 12CH and 13CH in United States)(Up to 3 channels that can be used simultaneously)(MHz)1CH2CH3CH4CH5CH6CH7CH8CH9CH10CH11CH12CH13CH24122417242224272432243724422447245224572462246724722.4GHz band802.11a: All of 24 channels (up to 24 channels that can be used simultaneously) globally common, indoors only(MHz) All Countries36CH 5180 100CH 5500104CH 5520108CH 5540112CH 5560116CH 5580120CH 5600124CH 5620128CH 5640132CH 5660136CH 5680140CH 570040CH 520044CH 522048CH 524052CH 526056CH 528060CH 530064CH 5320(MHz)5GHz band(MHz) United States only149CH 5745153CH 5765157CH 5785161CH 5805165CH 5825All Countries except FranceCable (AWG 26 to 17) Single Wire10 to 11 mmStripping Length■ Wiring Precautions• Signal lines and power lines must be separated to avoid influence of noise.• Do not lay cables close to antennas.• Wiring must be done while power is off.• Use a pin terminal and a cable for connection as shown below.0 to 0.5 mmInsufficient Stripping LengthDamage on SideWhiskerCorrectIncorrect• A pin terminal must be clamped with an appropriate tool based on its size.The tip of a wire must be cut in the same length as the pin terminal or 0.5mm longer. Whiskers are not allowed, and a pin terminal must not be broken.• Plug the pin terminal into the power terminal block to the end.Fix wiring close to its connector so that a cable should not apply load to the connector due to its twisting or weight.• A pin terminal must be unplugged while inserting a flat-head screw driver as shown below.● Main Unit Power WiringPower supply voltage of the wireless unit is 24VDC.A wireless unit requires 24VDC power supply.Use S8VM/VS series power source of 15W or higher, taking inrush current on startup into account.● Margin and SpacingFor heat release, ensure space between a wireless unit and a control panel or other equipment as shown in the right.Power supply voltage 24 VDCAllowable Voltage Range 20.4 to 26.4 VDCNotice on Safety Standards20mm or longer20mm or longerWE70-APLANMODEFA WIRELESS LAN ACCESS POINTPOWER WIRELESSWE70-APFA WIRELESS LAN ACCESS POINTLANMODEPOWERWIRELESS(+)( - )PluggingWE70-APFA WIRELESS LAN ACCESS POINTLANMODEPOWERWIRELESSUnplugging24V• This unit needs to be installed under local regulations.• This unit is intended to be supplied by a "Class 2" or "L.P.S. and rated from 24VDC, 250mA."120 ±1.0 (Unit: mm)34.5 ±0.536103 ±1.0 22.6107.6 ±1.0For WE70-CL OnlyETHERNETINITPUSHRSSI24VWE70-APLANMODEFA WIRELESS LAN ACCESS POINTPOWER WIRELESS■ Dimensions[LAN] Indicator (Orange)Displays a status of the wired LAN.On : LAN connection is normalOff : LAN is not being connectedFlashing: Data is being transmitted[MODE] Indicator (Orange)(WE70-AP)Displays an operation mode of the wireless unit.*1 [RSSI] indicator for WE70-CLDisplays receiving electric field intensity by flashing.Flashing: Simultaneous flashing of [MODE] and [POWER] indicates setup initialization.   Using 802.11a : On   Using 802.11b/g : OffWE70-APWE70-APLANMODEFA WIRELESS LAN ACCESS POINTPOWER WIRELESSLANRSSIPOWER WIRELESSLEVEL4LEVEL3LEVEL2LEVEL1LEVEL4LEVEL3LEVEL2LEVEL1Off Off:OnOn On On:On OnWhen the [RSSI] button on top of the unit is pressed, receiving electric field intensity is displayed on [RSSI], [LAN], and [WIRELESS] indicators in 4 levels.The [POWER] indicator flashes at the same time.Indication returns to its original status when 10 minutes passes or the button is pressed again.......Stable Level.....................Usable Level....................Unstable Level.................Unusable Level..........<Flashing> <On>RSSI[RSSI] Indicator (Orange)(WE70-CL)WE70-APWE70-CLETHERNETINITPUSHRSSIETHERNETINIT<INIT> ButtonInitializes setup.* Use a pen tip to press.See the WE70-AP/CL FA Wireless LAN Unit OPERA-TIONAL MANUAL (Cat.No.N153-E1), Chapter 6-2. "Restoring to Factory Shipment Status".DC ConnectorSupplies 24VDC power.RSSI ButtonSwitches receiving status indication.Flashing/4-Level[LAN] Port (RJ-45 x 1)Connects a network device such as a hub through a LAN cable.Antenna ConnectorConnects accessory antennas.* To ensure performance, always connect both  of 2 antennas.■ Components and Functions[POWER] Indicator (Green)Displays a power source status and a wireless unit operation mode.On : The wireless unit is turned on.Flashing: Simultaneous flashing of [POWER] and [MODE]*1 indicates setup initialization. Alternate flashing of [POWER] and [MODE]*1 indicates startup.[WIRELESS] Indicator (Orange)Displays a status of the wireless LAN.On: Radio communication is being established with the wireless unit.Off: Absence of wireless LAN terminal which is communicating with the wireless unit, or no radio communication has been made for 5 or more minutes (10 seconds for WE70-CL).■ Option List● Others● AntennaWE70-AT001HWT30-FT001WT30-FT002WE70-CA5MMagnetic Pedestal Antenna (2 antennas in 1 set)Supporting 2.4GHz/5GHz dual bandsDIN rail mounting bracket (for TH35-7.5)DIN rail mounting bracket (for TH35-15)Extension cable for 5MTypeTypeModelModel■ Contents• Main Unit: WE70-AP/WE70-CL• Antenna• Antenna Connector Cover• Magnet (with 4 flat-head screws)• Instruction Sheet • CE Declaration of Conformity• Mounting Bracket (with 4 flat-head screws) (with 4 tapping screws)• IP Address Label24V 24VPrecautions for Correct UseAlways heed these precautions to prevent faulty operation, malfunction, or adverse affect on the product's performance and functionality.1) Communication performance may be affected by its environment.Always confirm its operation before using it.2) Do not install its antenna where it is surrounded by metal, such as in a control panel.3) Install the antenna so that it is as far away as possible from and not parallel to electric wires or metal plates.4) Do not use this product in areas exposed to extremely high humidity, near televisions or radios, near motors or drills that emit sparks, near strong magnets, or near fluorescent lights.5) Do not pull or bend cables with force.

Navigation menu