Omron Okayama factory WE70CL FA Wireless LAN Unit - Client User Manual
Omron Corporation Okayama factory FA Wireless LAN Unit - Client Users Manual
Contents
- 1. Users Manual Part 1
- 2. Users Manual Part 2
Users Manual Part 2
■ Components and Functions ■ Channel assignment based on frequency band Connects accessory antennas. * To ensure performance, always connect both of 2 antennas. Displays a status of the wireless LAN. Displays a power source status and a wireless unit operation mode. On : The wireless unit is turned on. Flashing : Simultaneous flashing of [POWER] and [MODE]*1 indicates setup initialization. Alternate flashing of [POWER] and [MODE]*1 indicates startup. On : Radio communication is being established with the wireless unit. Off : Absence of wireless LAN terminal which is communicating with the wireless unit, or no radio communication has been made for 5 or more minutes (10 seconds for WE70-CL). (MHz) 1CH 2412 2CH 2417 3CH 2422 WE70-AP 4CH 2427 WE70-CL 5CH 2432 6CH 2437 7CH 2442 PUSH *1 [RSSI] indicator for WE70-CL 802.11b/g: All of 13 channels (except 12CH and 13CH in United States) (Up to 3 channels that can be used simultaneously) 2.4GHz band Antenna Connector [WIRELESS] Indicator (Orange) [POWER] Indicator (Green) INIT ETHERNET INIT ETHERNET 24V 8CH 2447 RSSI 24V 9CH 2452 WE70-AP 10CH 2457 11CH 2462 RSSI Button [LAN] Port (RJ-45 x 1) 12CH 2467 Switches receiving status indication. Flashing/4-Level Connects a network device such as a hub through a LAN cable. 13CH 2472 5GHz band WE70-AP DC Connector FA WIRELESS LAN ACCESS POINTButton Supplies 24VDC power. POWER MODE (MHz) Initializes setup. * Use a pen tip to press. See the WE70-AP/CL FA Wireless LAN Unit OPERATIONAL MANUAL (Cat.No.N153-E1), Chapter 6-2. "Restoring to Factory Shipment Status". LAN WIRELESS • Signal lines and power lines must be separated to avoid influence of noise. • Do not lay cables close to antennas. • Wiring must be done while power is off. • Use a pin terminal and a cable for connection as shown below. LAN WIRE LESS AC CE SS PO IN WE 70-A LA WI RE LE SS On LEVEL1 On Off 0 to 0.5 mm Damage on Side ......Usable Level.............. LEVEL3 (+) Incorrect ......Unstable Level........... LEVEL2 On: ......Unusable Level.......... LEVEL1 Off: FA LEVEL2 On On LEVEL3 LAN WIRELESS ......Stable Level............... LEVEL4 On MO DE POWER RSSI LEVEL4 POW ER Correct When the [RSSI] button on top of the unit is pressed, receiving electric field intensity is displayed on [RSSI], [LAN], and [WIRELESS] indicators in 4 levels.The [POWER] indicator flashes at the same time.Indication returns to its original status when 10 minutes passes or the button is pressed again. • Plug the pin terminal into the power terminal block to the end.Fix wiring close to its connector so that a cable should not apply load to the connector due to its twisting or weight. • A pin terminal must be unplugged while inserting a flat-head screw driver as shown below. PO IN Displays receiving electric field intensity by flashing. • A pin terminal must be clamped with an appropriate tool based on its size.The tip of a wire must be cut in the same length as the pin terminal or 0.5mm longer. Whiskers are not allowed, and a pin terminal must not be broken. AC CE SS RSSI (-) Whisker Plugging Insufficient Stripping Length Unplugging ● Main Unit Power Wiring Power supply voltage of the wireless unit is 24VDC.A wireless unit requires 24VDC power supply. Use S8VM/VS series power source of 15W or higher, taking inrush current on startup into account. ■ Dimensions For WE70-CL Only 22.6 24V ETHERNET INIT RSSI PUSH 34.5 ±0.5 20mm or longer LAN WIRELESS 120 ±1.0 (Unit: mm) WE70-AP FA WIRELESS LAN ACCESS POINT 36 POWER MODE LAN WIRELESS • CE Declaration of Conformity • Mounting Bracket (with 4 flat-head screws) (with 4 tapping screws) • IP Address Label WE70-AT001H 24V Type Magnetic Pedestal Antenna (2 antennas in 1 set) Supporting 2.4GHz/5GHz dual bands ● Others Model For heat release, ensure space between a wireless unit and a control panel or other equipment as shown in the right. 103 ±1.0 107.6 ±1.0 POWER MODE • Main Unit: WE70-AP/WE70-CL • Antenna • Antenna Connector Cover • Magnet (with 4 flat-head screws) • Instruction Sheet Model ● Margin and Spacing 20mm or longer ■ Contents ● Antenna • This unit needs to be installed under local regulations. • This unit is intended to be supplied by a "Class 2" or "L.P.S. and rated from 24VDC, 250mA." WE70-AP ■ Initiating Setup Screen (1) Configure an IP address and a subnet mask for PC. (2) Start a WWW browser. (3) Enter the IP address specified for the wireless unit in the address bar of the WWW browser. Enter http://192.168.0.1/ (factory shipment) for WE70-AP and http://192.168.0.254/ (factory shipment) for WE70-CL, then press [Enter] key. (4) In case of an access point, a password input is requested. Press [Enter] key while leaving the password field blank. (5) A Basic Setup screen of Network Setup menu is displayed at first. * To configure SSID and encryption of wireless LAN from PC connected to a wired LAN, See "WE70 AP/CL FA Wireless LAN Unit OPERATION MANUAL" (Cat.No.N153-E1). ■ Option List Power supply voltage 24 VDC Allowable Voltage Range 20.4 to 26.4 VDC Notice on Safety Standards FA WIRELESS LAN ACCESS POINT United States only All Countries except France 100CH 5500 104CH 5520 108CH 5540 112CH 5560 116CH 5580 120CH 5600 124CH 5620 128CH 5640 132CH 5660 136CH 5680 140CH 5700 Cable (AWG 26 to 17) Single Wire [RSSI] Indicator (Orange)(WE70-CL) 10 to 11 mm Stripping Length WE FA 70-A LA On : LAN connection is normal Off : LAN is not being connected Flashing : Data is being transmitted WI RE LE SS Flashing : Simultaneous flashing of [MODE] and [POWER] indicates setup initialization. Using 802.11a : On Using 802.11b/g : Off (MHz) 149CH 5745 153CH 5765 157CH 5785 161CH 5805 165CH 5825 LAN WIRE LESS Displays a status of the wired LAN. MO DE Displays an operation mode of the wireless unit. (MHz) POW ER [LAN] Indicator (Orange) All Countries 36CH 5180 40CH 5200 44CH 5220 48CH 5240 52CH 5260 56CH 5280 60CH 5300 64CH 5320 ■ Wiring Precautions [MODE] Indicator (Orange)(WE70-AP) 802.11a: All of 24 channels (up to 24 channels that can be used simultaneously) globally common, indoors only Precautions for Correct Use Always heed these precautions to prevent faulty operation, malfunction, or adverse affect on the product's performance and functionality. 1) Communication performance may be affected by its environment.Always confirm its operation before using it. 2) Do not install its antenna where it is surrounded by metal, such as in a control panel. 3) Install the antenna so that it is as far away as possible from and not parallel to electric wires or metal plates. 4) Do not use this product in areas exposed to extremely high humidity, near televisions or radios, near motors or drills that emit sparks, near strong magnets, or near fluorescent lights. 5) Do not pull or bend cables with force. Type WT30-FT001 DIN rail mounting bracket (for TH35-7.5) WT30-FT002 DIN rail mounting bracket (for TH35-15) WE70-CA5M Extension cable for 5M Contact Address OMRON ELECTRONICS LLC. After sales Support Engineering Service Department One Commerce Drive, Schaumburg. IL 60173-5302 U.S.A Phone: 1-847-843-7900 Fax: 1-847-843-7787 OMRON ELECTRONICS B.V. Wegalaan 61 2132 JD, HOOFDDORP, THE NETHERLANDS Phone: 31-23-56-81-100 Fax: 31-23-56-81-188
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2007:03:23 18:51:16+09:00 Creator : Adobe Illustrator 9.0.2 Producer : Adobe PDF library 4.800 Title : E_WE70„»ŁiŁ[4_B_0323.pdf Creator Version : 9 Container Version : 9 For : kitagawa tetsuya, iware Bounding Box : -848 -865 452 86 Page Count : 1EXIF Metadata provided by EXIF.tools