On Track Innovations OTI-SATURN Contactless Smart Card Reader User Manual Revised
On Track Innovations Ltd Contactless Smart Card Reader Users Manual Revised
Users Manual Revised
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 294381 |
| Application ID | iUY5eBnvS/Sko0y3rpQRVQ== |
| Document Description | Users Manual Revised |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 74.46kB (930694 bits) |
| Date Submitted | 2003-01-08 00:00:00 |
| Date Available | 2003-01-08 00:00:00 |
| Creation Date | 2002-10-31 17:23:26 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2003-01-08 17:04:07 |
| Document Title | Users Manual Revised |
Saturn User Manual Version 1.00 FCC Compliance Saturn Reader User Manual Version 1.00 On Track Innovations Ltd. (O T I) P/N 1100054F P/N 1100054F page 0 Saturn User Manual Version 1.00 FCC Compliance FCC Compliance This device (Reader Saturn 3000) complies with Part 15, of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation • NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15, subpart C of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Changes or modifications in this equipment, not expressly approved by the party responsible for compliance (On Track Innovations Ltd,) could void the user’s authority to operate the equipment. FCC ID: JNX-OTI-SATURN Responsible Party: OTI America Inc. 1601 South DeAnza Blvd. Cupertino, CA95014 USA Phone: 408-252-0333 P/N 1100054F page 1 Saturn User Manual Version 1.00 Table of Contents Table of Contents FCC COMPLIANCE...................................................................................................................... 1 TABLE OF CONTENTS................................................................................................................ 2 1. 2. 3. PRODUCT OVERVIEW....................................................................................................1-1 1.1 PRODUCT DESCRIPTION ....................................................................................................1-1 1.2 PRODUCT FEATURES .........................................................................................................1-4 1.3 PRODUCT SPECIFICATIONS................................................................................................1-5 1.4 SATURN READER PCB INTERFACE SUMMARY BY REFERENCE DESIGNATION ...............1-7 1.4.1 Connectors .............................................................................................................1-9 1.4.2 LEDs.......................................................................................................................1-9 1.4.3 Jumpers ................................................................................................................1-10 1.4.4 Tuning Capacitors................................................................................................1-10 1.4.5 Test Points ............................................................................................................1-10 1.4.6 SAM ......................................................................................................................1-10 PCB MECHANICAL INSTALLATION ..........................................................................2-1 2.1 PCB MOUNTING DIMENSIONS ..........................................................................................2-1 2.2 PCB MOUNTING INSTRUCTIONS .......................................................................................2-1 2.2.1 Enclosure................................................................................................................2-1 2.2.2 Ventilation ..............................................................................................................2-1 INTERFACE CONNECTIONS.........................................................................................3-1 3.1 COMMUNICATION CONNECTORS.......................................................................................3-1 3.1.1 3.2 DIGITAL IO CONNECTORS ................................................................................................3-2 3.2.1 Antenna Board Connector P1 ................................................................................3-2 3.2.2 Optional I/O Connector P2 ....................................................................................3-3 3.3 POWER CONNECTION ........................................................................................................3-3 3.3.1 4. RS232 Serial Interface connector CJ1 ...................................................................3-1 Power input Jack P7...............................................................................................3-3 JUMPER & MODE SETTINGS........................................................................................4-1 4.1 TRANSMISSION JUMPER J1................................................................................................4-1 P/N 1100054F page 2 Saturn User Manual Version 1.00 Table of Contents 5. 4.2 TRANSMISSION MODULATION JUMPER J3.........................................................................4-1 4.3 ANTENNA JUMPER J4........................................................................................................4-1 4.4 TRANSMITTER CARRIER JUMPER J5..................................................................................4-1 4.5 NORMAL OPERATION JUMPER SETTINGS ..........................................................................4-2 4.6 SELECTION OF OPERATING MODE AND BAUD RATE .........................................................4-2 FLASH MEMORY PROGRAMMING ............................................................................5-1 5.1 INTRODUCTION .................................................................................................................5-1 5.2 PC REQUIREMENTS ...........................................................................................................5-1 5.3 PROGRAMMER SOFTWARE INSTALLATION ........................................................................5-1 5.4 HARDWARE SETUP ...........................................................................................................5-1 5.5 PROGRAMMING.................................................................................................................5-2 5.5.1 Flash Memory Files................................................................................................5-2 5.5.2 Programming Procedure........................................................................................5-2 5.6 HELP .................................................................................................................................5-2 P/N 1100054F page 3 Saturn User Manual Version 1.00 Product Overview 1. Product Overview 1.1 Product Description 12VDC UNREGULATED SUPPLY SMART CARD SATURN Reader Antenna CONTACTLESS Smart Card Interface BUZZER PWR Digital Indicators CONT TX RS232 Host RX Contact Card Acceptor L.S. CARD IN PLACE Antenna PCB CONTACT Smart Card Interface Reader PCB Figure 1-1: SATURN Reader System Block Diagram The SATURN Reader is an inexpensive, compact radio frequency communications electronic interface unit. With bi-directional contact & contactless communication to smart cards and RS232 communication to local controllers, the SATURN reader is the key stone in contactless smart card systems. The SATURN Reader can be integrated into existing systems. Using RS232 serial communication interface between reader and Host, the Saturn allows bidirectional, full duplex communication between the Host and passive, contactless smart card. P/N 1100054F page 1-1 Saturn User Manual Version 1.00 Product Overview The SATURN OEM Reader Board serves as a smart interface unit between the application controller and: 1. ISO14443 Type B Contactless smart cards. 2. SAM Secured Applications Module 3. Contact smart cards. Contact cards The SATURN provides interface (T=0 and T=1) between the contact card and the Application Controller. Communication with the contact card acceptor is TTL NRZ. Contactless Cards At the Host’s command, the SATURN generates and modulates a 13.56 MHz carrier signal for the transmission of power, commands and data to an in-range smart card. Read and write operations have equal data rates and range. Secured Transactions Secured Purse to Purse transactions can be achieved either between a Contact card and a Contactless card or between cards (contact or contactless) and an “on board” SAM Secured Applications Module Indicator LEDs Nine on board indicator LEDs are provided. (see 1.4.2 ) Digital IO The Saturn provides interface to an external contact card acceptor as well as external indication LEDS and user configurable sink type digital IO. P/N 1100054F page 1-2 Saturn User Manual Version 1.00 Product Overview LEDS Digital IO (Antenna Board) (Optional) P1 P6 Serial Interface CJ1 +5V RXD TXD Microprocessor and digital section ON/OFF TXD RCD CLK DATA RST SAM SATURN READER RS232 Driver J7 RX DISABLE 5MHz +5V 7.5V Enable 24MHz 13.56MHz Oscilator VTX N J3 Modulator OFF +5V Amplifier N J5 C7 OFF (G) TRANS D3 TRANSMITTER Power Supplies RX DISABLE +5V TP4 +5V TP5 RCD SQUELCH BPSK Demodulator (Digital) D5 P5 1K Detector Sub-carrier Amplifier (Analog) VTX +9V D29 J4 50 Ohm (G) GND REG 9V P3 (R) REG 5V +5V Matching Circuit RECEIVER (Y) REG 8V (Y) D7 D30 1K 1Oh C7 D6 (R) P7 SIG Power Input Jack ANTENNA Figure 1-2: SATURN Reader Schematic Diagram P/N 1100054F page 1-3 Saturn User Manual Version 1.00 Product Overview 1.2 Product Features Bi-directional radio frequency interface between Host and Contactless Smart Cards Bi-directional interface to Contact Smart Cards Flexible, software configurable microcomputer-based design. Integrated, sophisticated Smart Card Operating System on board. High security encryption system (DES/RSA) in the board’s Operating System (with SAM option on-board). 13.56 MHz transmission frequency conforming to ISO 14443 standard. ISO 14443 Type B transmission of commands and data to/from the card. Equidistant read/write transaction operation. Proximity range - up to 6 cm. Signal penetrates virtually any non-conductive material - no contact or line-of-sight required. Bi-directional data transmission from/to the EYECON at 50/106 kbps. RS232 Communications interface to Host controller. SAM “on-board” option. Simultaneous transmission of power and bi-directional read write messages, through its antenna, to the passive smart card. Indicator LEDs for Power, Card Detected, RF Transmit/ Receive. Flash programmable digital IO. Operating temperature range 0°C to 70°C (32°F to 158°F). Single 12V 500mA non-regulated power supply. Firmware stored in on-line programmable Flash memory. P/N 1100054F page 1-4 Saturn User Manual Version 1.00 Product Overview 1.3 Product Specifications Table 1-1: Performance/Electrical Specifications ! Contactless Read/Write Range: Up to 6 centimeters with Contactless Smart Card (depending on card type and orientation). ! RF Interface: RF Carrier Frequency RF Output Output Short Protection RF Data Operations RF Data Transmission Rate Data Error Checking ! Contact Card Interface Data line Reset line Clock Data Error Checking 13.56 MHz 200mW Built-in (continuous) Half duplex 50/106 kbps Message Length, Parity, Frame , Bits , CRC. TTL level Bi-directional, Half duplex 5MHz Message Length, Parity, Frame , Bits , CRC. ! Host Data Communications Interface ! TTL NRZ/ RS232 Transmit, receive ! Signals Bit/Byte Protocol Async (start/stop), bit serial, full duplex, 9600/38400 baud; data byte=8 data bits, no parity, 2 stop bits, full 8-bit binary data Data Error Checking Message Length , Parity , Frame , Bits , CRC. Connector/Cable Standard connectors on board ! Indicators: +5V Power +9V Power Transmit Receive B Red LED Red LED Green LED (x2) Yellow LED P/N 1100054F page 1-5 Saturn User Manual Version 1.00 Product Overview Performance/Electrical Specifications (continued) ! Digital I/O: ! Microprocessor Circuit Microprocessor XTAL FLASH MEMORY RAM LOCK-UP PROTECTION Serial TTL Level 80C32 - PLCC - 24MHz 24 MHz 128Kbyte 8Kbyte Watch Dog Timer ! Electronic Board Power Requirements: Maximum Current Draw 12VDC @ 500mA (non-regulated) 300 mA ! Mechanical: Dimensions Weight Vibrations 125x102x20mm 100 gr. 10 ÷ 200 Hz @ 2.0G Environmental ! Temperature: Operating Storage ! Humidity: 0° to 70°C (32° to 158°F) -25° to 85°C (-13° to 185°F) 5 to 95% non-condensing ! Tuning RF output filter SQUELCH ! Secured Applications Secured applications with SAM option P/N 1100054F page 1-6 Saturn User Manual Version 1.00 Product Overview 1.4 SATURN Reader PCB Interface Summary by Reference Designation TP5 P5 TP6 C7 J4 J3 J5 P1 C13 D6 D7 P4 P3 J7 J1 U7 D5 D3 P7 P6 Figure 1-3: SATURN Reader PCB Layout Front P/N 1100054F page 1-7 Saturn User Manual Version 1.00 Product Overview SAM D30 D29 Figure 1-4: SATURN Reader PCB Layout Back P/N 1100054F page 1-8 Saturn User Manual Version 1.00 Product Overview 1.4.1 Connectors P1 14 pin digital I/O connector to Antenna PCB. P3 3 pin Antenna connector to Antenna PCB. P4 2 pin connector for measurement of transmitter voltage. P5 2 pin connector for measurement of transmitter current. P6 Optional 14 pin digital I/O connector. P7 12VDC power input jack connector. (+=Center) CJ1 RJ45 connector for RS232 serial communication to host. 1.4.2 LEDs D3 Transmit indicator (green). D5 Receive indicator (yellow). D6 +5V (red). D7 +9V (red) D29 Transmit indicator (green). D30 Squelch indicator (yellow). P/N 1100054F page 1-9 Saturn User Manual Version 1.00 Product Overview 1.4.3 Jumpers J1 Transmit selector: (MT/CONT/OFF) J3 Transmitter modulation selector: (MT/CONT/OFF) J4 Antenna selector: Normal Transmission to antenna/50Ω load at transmitter output (maintenance only). J5 Transmitter carrier selector: (MT/CONT/OFF) J7 Optional connection to external SAM. 1.4.4 Tuning Capacitors C7 Transmitter tuning. C13 Antenna matching variable capacitor VCp 1.4.5 Test Points TP5 Squelch measuring point. TP6 Received data input to µP measuring point. 1.4.6 SAM SAM Secured Applications Module. P/N 1100054F page 1-10 Saturn User Manual Version 1.00 PCB Mechanical Installation 2. PCB Mechanical Installation 2.1 PCB Mounting Dimensions All dimensions are in millimeters Figure 2-1: PCB Mounting Drawing 2.2 PCB Mounting Instructions 2.2.1 Enclosure The SATURN OEM Reader should be mounted in a protective enclosure. The Reader Board has 4x4.57 mm diameter mounting holes. If mounted on a metallic surface, spacers are required to prevent contact between the Reader Board and the metallic surface. The reader can be mounted directly on to the main controller motherboard. For this option, the pins of connectors P1and P6 can be connected to the bottom of the board to enable piggyback mounting of the reader PCB. 2.2.2 Ventilation The SATURN OEM Reader Board does not require ventilation for component cooling purposes. P/N 1100054F page 2-1 Saturn User Manual Version 1.00 Interface Connections 3. Interface Connections 3.1 Communication Connectors 3.1.1 RS232 Serial Interface connector CJ1 Saturn 9 Pos. RJ45 Connector Host DB9 Female Connector DTR Optional Optional 4 DTR DSR 3 6 DSR GND 4 5 GND RXD 5 3 TXD TXD 6 2 RXD CTS 7 7 RTS RTS 8 8 CTS Figure 3-1: RS232 Serial Interface connector CJ1 CJ1 RJ45 type connector for RS232/TTL serial communication to Host. Note: CTS is shorted to RTS and DTR is shorted to CD on the SATURN PCB. P/N 1100054F page 3-1 Saturn User Manual Version 1.00 Interface Connections 3.2 Digital IO Connectors 3.2.1 Antenna Board Connector P1 GND +5V CONTACT CARD ACCEPTOR VDD C5 RST C6 RST C7 GND C1 IO C2 TEST C8 10 12 11 SW P1 14 13 +5V +12V (G) TX (Y) RX (R) GND PWR CONT BUZZER Figure 3-2: Antenna Board Connector P1 Pin 1 - +5Vdc out. Pin 3 - +12Vdc out. Output common Pin 5 – Transmit LED output. (Sink) Pin 7 – Receive LED output. (Sink) Pin 9 – Contact card in place indicator. (Sink) Pin 11 – Buzzer output. (Sink) Pin 14 - GND. Pins 2,4,6,8,10,12, – Connections to contact card acceptor. Pin 14 – Input from “contact card in place” indicator switch. P/N 1100054F page 3-2 Saturn User Manual Version 1.00 Interface Connections 3.2.2 Optional I/O Connector P2 IN IN IN IN IN 10 OUT OUT OUT OUT OUT GND INPUT COMMON P2 12 11 14 13 +5V OUT 7 OUTPUT COMMON Figure 3-3: I/O Connector P1 Pins 1,3,5,7,9, - Programmable digital outputs 0 to 4. (Sink) Pin 11 - Programmable digital output 7. (Sink) Pin 13 – +5V (output common). Pins 2,4,6,8,10 – Programmable digital inputs 0 to 4. (Sink) Pin 12 – Not connected. Pin 14 – GND (input common). 3.3 Power Connection 3.3.1 Power input Jack P7 P7 GND +12V Figure 3-4: SATURN Power Input Jack Power supply to the SATURN OEM reader is made via 2.5mm input jack P7. (+V connected to center pin) P/N 1100054F page 3-3 Saturn User Manual Version 1.00 Jumper & Mode Settings 4. Jumper & Mode Settings 4.1 Transmission Jumper J1 1) N position - normal microprocessor controlled data transmission. 2) Off position - no RF signal. 3) No jumper - constant RF signal. 4.2 Transmission Modulation Jumper J3 1) Normal position (N) - normal microprocessor controlled data modulation. 2) 80% position (OFF) – Carrier level at 80%. 3) No jumper – Carrier level at 100%. 4.3 Antenna Jumper J4 1) Normal position (N) - transceiver connected to antenna. 2) Resistor position - transceiver connected to 50Ω load. 3) No jumper - Transceiver disconnected. 4.4 Transmitter Carrier Jumper J5 1) Normal position (N) - normal microprocessor controlled carrier transmission. 2) Off position - no carrier transmission. 3) No jumper - constant carrier transmission. P/N 1100054F page 4-1 Saturn User Manual Version 1.00 Jumper & Mode Settings 4.5 Normal Operation Jumper Settings 1) Jumpers J1, J3, J4 and J5 should be placed in N position 4.6 Selection of Operating Mode and Baud Rate The operating system mode and baud rate settings may be changed during operation by transmitting the following ASCII strings: 1) MODE0 - switches from Host Mode to OEM Mode. MODE0 → Response M0 2) MODE1 - switches from OEM Mode to Host Mode. MODE1 → Response M1 3) BAUD0 - switches to 9600-baud rate. BAUD0 → Response B0 4) BAUD1 - switches to 19200-baud rate. BAUD1 → Response B1 P/N 1100054F page 4-2 Saturn User Manual Version 1.00 Flash Memory Programming 5. Flash Memory Programming 5.1 Introduction The SATURN OEM reader’s program is stored in it’s non volatile Flash Memory. Application versions and updates to the SATURN OEM reader’s program, may be written only at OTI. The application versions and updates can be programmed into the SATURN OEM reader’s Flash memory by the customer through use of the Flash Memory Programmer software, described in the following paragraphs. 5.2 PC requirements ! Flash Memory Programmer software runs on Windows 95 or Windows NT 32bit operating systems. ! PC should be at least a 486 DX2. Program loading time depends on the speed of PC. 5.3 Programmer Software Installation 1. Run the setup.exe file from diskette No. 1. 2. Follow the instructions on the PC screen. 5.4 Hardware Setup 1. Connect RS232 cable between PC and SCI interface. Note: DTR and DSR as well as CTS and RTS in the PC connector should be shorted. For 25 pin D type connector, short between 4 & 5 and between 6 & 20. For 9 pin D type connector, short between 4 & 6 and between 7 & 8. 2. Apply power to the reader P/N 1100054F page 5-1 Saturn User Manual Version 1.00 Flash Memory Programming 5.5 Programming 5.5.1 Flash Memory Files The flash memory files, written at OTI can be loaded into the PC from diskettes or through the Internet. The prefix of the flash memory files is SCI5, followed by a four-character application code, followed by the date. 5.5.2 Programming Procedure 1. Run the Flash Programmer software 2. Choose the communication port 3. Press the “Load” button. A dialogue window opens, 4. Select the file to be programmed into the SATURN OEM reader. The selected file is validated as an SCI5flash memory file. 5. Press the “Program” button. The programmer will start programming the selected file into the flash memory. If the SATURN OEM reader is already programmed, the programmer will issue a warning and wait for an approval to continue by pressing the “yes” button The system automatically finds and switches to the fastest Baud rate possible. 6. After programming the file into the flash memory, the programmed file is verified, and a “ valid version” flag in the SATURN OEM reader’s memory is set. 7. The SATURN OEM reader is ready to operate with the new program file. 5.6 Help A comprehensive Help section provides the user with detailed explanations regarding the operation of the Flash Memory Programmer software. P/N 1100054F page 5-2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:10:31 17:23:26 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2003:01:08 17:04:07+02:00 Page Count : 22EXIF Metadata provided by EXIF.tools