Opticon Sensors Europe PX20 PX-20 User Manual PX20 datacollector

Opticon Sensors Europe BV PX-20 PX20 datacollector

User manual

Specifications Manual Portable 2D Data Collector PX-20 The PX-20 is a portable data collector with a 2D barcode scanner. Scanned and stored data can be transmitted to the host via the USB interface, or via Bluetooth.
Opticon PX-20 Specifications Manual 2 Preliminary. All information subject to change without notice. Document History Model Number: PX-20 Edition: 1.3 Date: 2013-05-30 Copyright 2013 Opticon. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon. Limited Warranty and Disclaimers PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE PRODUCT. Serial Number A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty. Warranty Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages. Packaging The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty. Trademarks Trademarks used are the property of their respective owners. Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12- 17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184 SUPPORT USA Europe Phone: 800-636-0090 Email: support@opticonusa.com Email: support@opticon.com Web: www.opticonusa.com Web: www.opticon.com
Opticon PX-20 Specifications Manual 3 Contents 1. Abstract ..................................................................................................................................... 5 2. Overview ................................................................................................................................... 5 3. Physical Features ..................................................................................................................... 6 3.1. Dimensions ....................................................................................................................... 6 3.2. Weight ............................................................................................................................... 7 3.3. Color ................................................................................................................................. 7 4. Environmental Specifications.................................................................................................. 7 4.1. Operating Temperature and Humidity................................................................................ 7 4.2. Storage Temperature and Humidity ................................................................................... 7 4.3. Ambient Light Immunity ..................................................................................................... 7 5. Component Specification......................................................................................................... 8 6. Electrical Specifications........................................................................................................... 8 6.1. Absolute Maximum Ratings ............................................................................................... 8 6.2. Recommended Operating Conditions ................................................................................ 8 6.3. Electrical Characteristics ................................................................................................... 9 7. Optical Specifications ............................................................................................................ 10 8. Barcode reader Technical Specifications ............................................................................ 11 8.1. Bar Code Test Sample .................................................................................................... 12 8.2. Scan Area and Depth of Field.......................................................................................... 13 8.3. Print Contrast Signal........................................................................................................ 14 8.4. Minimum Resolution ........................................................................................................ 14 8.5. Wide Bar Code ................................................................................................................ 14 8.6. Motion Tolerance............................................................................................................. 15 8.7. Pitch, Skew, and Tilt ........................................................................................................ 16 8.8. Curvature ........................................................................................................................ 16 9. External interfaces.................................................................................................................. 17 9.1. USB-HID and USB-VCP Interface Specifications ............................................................ 17 9.2. Wireless Interface............................................................................................................ 17 10. Cable and Connector.............................................................................................................. 18 10.1. USB Cable ...................................................................................................................... 18 10.2. Connector........................................................................................................................ 18 10.3. External trigger ................................................................................................................ 18 11. Labeling................................................................................................................................... 19 11.1. Product label ................................................................................................................... 19 11.1. White box label ................................................................................................................ 19
4 Opticon PX-20 Specifications Manual 12. Packaging Specifications....................................................................................................... 21 12.1. Individual Packaging Specification................................................................................... 21 12.2. Collective Packaging Specification .................................................................................. 22 13. Durability ................................................................................................................................. 23 13.1. Drop Test ........................................................................................................................ 23 13.2. Dust and water Proof ....................................................................................................... 23 14. Regulatory Compliance.......................................................................................................... 24 14.1. Product Safety................................................................................................................. 24 14.2. EMC ................................................................................................................................ 24 14.3. REACH............................................................................................................................ 24 Regulation (EC1907/2006) compliance..................................................................................... 24 14.4. RoHS .............................................................................................................................. 24 14.5. R&TTE ............................................................................................................................ 25 15. Handling .................................................................................................................................. 26 15.1. Shock .............................................................................................................................. 26 15.2. Temperature Conditions .................................................................................................. 26 15.3. Foreign Materials............................................................................................................. 26 15.4. Other ............................................................................................................................... 26 16. Revision History ..................................................................................................................... 27 Table of Figures Figure 1: Dimensions .................................................................................................................. 6 Figure 2: USB Micro-B connector ............................................................................................. 18 Figure 3: Product label.............................................................................................................. 19 Figure 4: White box label .......................................................................................................... 20 Figure 5: Individual packaging .................................................................................................. 21 Figure 6: Collective packaging .................................................................................................. 22 Figure 7: Drop test .................................................................................................................... 23
5 Opticon PX-20 Specifications Manual 1. Abstract This manual provides specifications for the PX-20 portable 2D barcode data collector. 2. Overview The PX-20 is a very compact data collector with a built-in 2D barcode scanner. Due to its compact size and its Bluetooth capabilities, the PX-20 is the ideal companion scanner for mobile devices like the iPhone/iPad and Android telephones and tablets. The supported Bluetooth profiles are HID (keyboard emulation) and SPP (serial port emulation) Special support is added for iOS devices that allows for the use of the on-screen keyboard, while the PX-20 is connected. Additional to the Bluetooth wireless capabilities, the PX-20 also has a 1MByte storage space for off-line use. The USB interface can then be used to download the data. This is then again either as HID (keyboard emulation) or VCP (serial port emulation). The PX-20 is fully programmable, using Opticon’s easy to use development tools that are available for free.
6 Opticon PX-20 Specifications Manual 3. Physical Features 3.1. Dimensions (W) 36 x (L) 74 x (D) 16 mm Figure 1: Dimensions
7 Opticon PX-20 Specifications Manual 3.2. Weight 40 g (estimated) 3.3. Color Black 4. Environmental Specifications 4.1. Operating Temperature and Humidity Temperature: -10 to 50° C (Charging temperature range 0 to 45° C) Humidity: 20% to 90% RH 4.2. Storage Temperature and Humidity Temperature: -20 to 60° C Humidity: 20% to 85% RH 4.3. Ambient Light Immunity Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values: Incandescent light 10,000 lx Fluorescent light 10,000 lx Sunlight 100,000 lx Conditions Barcode Sample: OPTOELECTRONICS Test Sample Bar Code Sample : 0.33 mm UPC specified in Chapter 8 Distance : 130 mm from the front edge of the camera module Angle : α = 0°, β =＋15°, γ = 0° Curvature : R = ∞ Power Supply Voltage : 3.3 and 5.0 V Note: α, β and γ respectively represent pitch, skew and tilt.
8 Opticon PX-20 Specifications Manual 5. Component Specification Item Specifications Notes 2D Engine MDI-3100 Opticon’s 2D imager with integrated high speed decoder Application processor: Renesas RX62N 96 MHz Clock speed Flash ROM: 1 MByte serial flash Barcode storage + >50,000 barcodes + time stamp. Might be used for other purpose as well, depending on the users application. 512Kbyte program flash 128Kbyte available for user applications 32Kbyte config flash For configuration storage (e.g. Bluetooth link addresses) RAM 96KByte 16Kbyte available for user applications Keys + and - Dome switches LED RGB Bluetooth CSR 8811 6. Electrical Specifications 6.1. Absolute Maximum Ratings Parameter Symbol Value Unit Power supply voltage (VDD to GND) VDD -0.3 to 6.5 V Input voltage VIN -0.5 to VDD +0.5 V Power ripple 0.1 V p-p (10-100 kHz) V 6.2. Recommended Operating Conditions Item Symbol Conditions Min Typ Max Unit Power supply voltage VDD Battery 3.5 - 4.2 Ｖ USB 4.5 5.0 5.5 Ｖ Input voltage Vin 0 － VDD Ｖ
9 Opticon PX-20 Specifications Manual 6.3. Electrical Characteristics Parameter Symbol Min Typ Max Unit Operating current While Scanning IOP 350 400 mA While in Standby IPRE 45 50 mA While Charging ICHG1 350 400 mA When OFF Ioff 100 150 μA Battery specifications Voltage VBAT 2.75 3.7 4.2 V Rated capacity 350 355 - mAh Charging current ICHG2 160 mA Charging time Tchg - - 2.5 hour Scans when fully charged *1 Operating time - - 1500 20 - - - - Times Hours Scans when fully charged *2 Operating time - - 2500 35 - - - - Times Hours Startup time (from deep sleep) Td 75 - - ms Notes *1 One scan of 1 second per minute, Bluetooth link active, data transmitted immediately after the scan.. *2 One scan of 1 second per minute, Bluetooth link not active.
10 Opticon PX-20 Specifications Manual 7. Optical Specifications Item Characteristics Scan method CMOS area sensor (black and white) Nr of effective pixels 752 (H) x 480 (V) Dots Image capture speed (*1) 60 fps Frames per second Focal distance 130 mm View angle Horizontal 40.6° Vertical 26.4° Auxiliary light source (LED x 2) Red LED Peak wave length 617nm Directivity angle 2θ1/2 (*2) 60° Maximum radiation output (*3) 15000mcd Light source for aiming Green LED Peak wave length 528nm Maximum radiation output (*3) 18700mcd Notes: *1 The fastest speed of image capture *2 Typical value *3 Typical value at 25 °C
11 Opticon PX-20 Specifications Manual Ambient Temperature and Humidity : Room temperature and room humidity Ambient Light : 100 ~200 lux (on the surface of a bar code) Pitch Angle : α= 0° Skew Angle : β = 15° Tilt Angle : γ = 0° Curvature : R = ∞ Power Supply Voltage : 3.3 and 5.0 V PCS (1D and 2D) : 0.9 or higher Scanning Test : Accept the performance with 90% or more success rate for 10 tries of scan. One scan should be tested within 2 seconds. Bar Code Test Sample (1D and 2D) : Specified below 8. Barcode reader Technical Specifications Scanning is done by pointing the PX-20’s aiming light to the center of a bar code for scanning. The conditions for technical specifications are as follows, unless otherwise specified in each section. <Conditions> < Test chart > For 1D codes, OPTOELECTRONICS test samples For GS1 Databar, stacked codes and 2D codes, printed by a dedicated printer for bar code
12 Opticon PX-20 Specifications Manual 8.1. Bar Code Test Sample 1 D Bar Codes <Code 39> Resolution Symbology PCS Size (mm) No. of Digits 0.127 mm (5mil) Code 39 0.9 32 × 10 15 0.20 mm (7.9mil) 100 × 10 31 0.254 mm (10mil) 32.5 × 10 7 0.508 mm (20mil) 36 × 25 4 <Code 128> Resolution Symbology PCS Size (mm) No. of Digits 0.20 mm (7.9mil) Code 128 0.9 42 × 10 16 <UPC> Resolution Symbology PCS Size (mm) No. of Digits 0.330 mm (13mil) 12-digit UPC 0.9/0.3 31.5 × 25.0 12 <Codabar> Resolution Symbology PCS Size (mm) No. of Digits 0.15 mm (6mil) Codabar 0.9 20 × 10 10 GS1 Databar <GS1-limited> Resolution Symbology PCS Size (mm) No. of Digits 0.169 mm (6.7mil) Limited 0.9 12 × 1.5 14 0.169 mm (6.7mil) Limited-Composite 0.9 12 × 3.0 26 2 D Codes <PDF417> Resolution Error Correction PCS Size (mm) No. of Character 0.169 mm (6.7mil) Level-3 0.9 23 × 10 58 0.254 mm (10mil) 35 × 15 <QR Code: Model-2> Resolution Error Correction PCS Size (mm) No. of Character 0.212 mm (8.4mil) M 0.9 6 × 6 44 0.381 mm (15mil) 11 × 11 <Data Matrix> Resolution Model PCS Size (mm) No. of Character 0.212 mm (8.4mil) ECC200 0.9 5 × 5 40 0.254 mm (10mil) 6 × 6 Note: The size is outline dimensions excluding quiet zone.
13 Opticon PX-20 Specifications Manual 8.2. Scan Area and Depth of Field The scan area is measured from the front edge of the camera module. 50 100 150 200 250 300 Code 39 0.127(5mil) 90 130 0.254(10mil) 70 210 [ Unit ： mm ] 0.508(20mil) * 65 300 Code 128 UPC 100% 0.20(7.9mil) 80 190 0.33(13mil) 55 225 PDF417 0.169(6.7mil) 85 0.254(10mil) 65 145 200 QR Code Data Matrix 0.212(8.4mil) 95 120 0.381(15mil) 60 200 0.254(10mil) 80 150 Note: The depth of field depends on the view angle and symbol length
14 Opticon PX-20 Specifications Manual MRD : 32% and higher (70% or higher reflectivity of space and quiet zone) Distance : 130 mm from the front edge of the camera module Bar Code Sample : UPC specified in Chapter 8. (Resolution: 0.33 mm, PCS: 0.3) Bar Code Sample : The above codes specified in Chapter 8 Distance : 100 mm from the front edge of the camera module Angle : α = 0°, β =＋15°, γ = 0° Curvature : R = ∞ For the pitch angle and tilt angle measurement, set the skew angle β = +15° Bar Code Sample : 0.20 mm Code 39 specified in Chapter 8 Distance : 160 mm from the front edge of the camera module Angle : α = 0°, β =＋15°, γ = 0° Curvature : R = ∞ Figure 3: Scan Area and Depth of Field 8.3. Print Contrast Signal PSC 0.3 or higher <Conditions> MRD = Minimum reflectance of white bar - Maximum reflectance of black bar PCS = Error! 8.4. Minimum Resolution 1D Code : 0.127 mm (5 mil) Code 39 specified in Chapter 8 GS1-Databar : 0.169 mm (6.7 mil) GS1 Databar-Limited specified in Chapter 8 Stacked Code : 0.169 mm (6.7 mil) PDF417, GS1 Databar-Limited Composite specified in Chapter 8 2D Code : 0.212 mm (8.4 mil) OR Code and Data Matrix specified in Chapter 8 <Conditions> 8.5. Wide Bar Code Code 39 with width of 100 mm and resolution of 0.2 mm can be read. <Conditions> Figure 4: Wide Bar Code
15 Opticon PX-20 Specifications Manual Ambient Temperature and Humidity : Room temperature and Room humidity Ambient Light : 500 lux to 1000 lux (on the surface of a bar code) Distance : 130 mm from the front edge of the camera module Angles : α= 0° Skew : β = 15° Tilt : γ = 0° Curvature : R = ∞ Power Supply Voltage : 3.3 and 5.0 V PCS (1D and 2D) : 0.9 or higher Bar Code Sample : UPC with 0.33 mm resolution specified in Chapter 8 8.6. Motion Tolerance UPC bar code 100% can be read when it is moving at 2m/s. <Conditions> Figure 5: Motion Tolerance Note: The above shows the possible speed of reading, but no guarantee of 100% reading. : Scanning may fail due to the specular reflection of illumination LEDs when the reflectivity is high.
16 Opticon PX-20 Specifications Manual Bar Code Sample : 0.33 mm UPC specified in Chapter 8 Distance : 130 mm from the front edge of the camera module Curvature : R = ∞ For the pitch angle and tilt angle measurement, set the skew angle β = +15° Bar Code Sample : 0.33 mm UPC specified in Chapter 8 Distance : 110 mm from the front edge of the camera module Angle : α = 0°, β =＋15°, γ = 0° 8.7. Pitch, Skew, and Tilt Pitch : α = ±50° Skew : β = ±50° Tilt : γ = ±180° <Conditions> α β － － ＋ γ ＋ ＋ － Figure 6: Pitch, Skew, and Tilt 8.8. Curvature 0.33 mm 12-digit UPC : R ≧ 20 mm 0.15 mm 10-digit Codabar : R ≧ 16 mm <Conditions> R Figure 7: Curvature Note: Scanning may fail due to the specular reflection of illumination LEDs when the reflectivity is high.
17 Opticon PX-20 Specifications Manual 9. External interfaces Interface Specifications 9.1. USB-HID and USB-VCP Interface Specifications Complies with USB Version 2.0. The supported profiles are USB-COM (also referred to as USB-VCP that stands for Virtual Communication Port). This port is used for charging and data communication. 9.2. Wireless Interface PX-20 has a BT connection with the following features: Feature Description Version 1) 2.1 Supported profiles 1) SPP (Serial Port Profile) HID (Human Interface Device Profile) Scanner operating mode while connected to the host system Master or Slave mode Security mode As per the Bluetooth 2.1 specification. The settings for this can be configured in the user application. Encryption Encryption is linked to the authentication setting and cannot be enabled or disabled separately. Communication range 3) Approximately 10 meters Frequency 4) 2400 MHz to 2483.5 MHz Transmission power 2.5mW (4dBm) or less Baud rate 115.2 kbps Antenna 5) Built in Notes 1. This product complies with the Bluetooth 2.1 standard. The device that communicates with this product must support either SPP or HID as well. For other Bluetooth devices with other profiles we cannot guarantee a connection before the products have been tested. 2. The communication speed and range of the product may vary due to obstacles and radio wave conditions between this product and the device to which it is connected. Conditions on the host device may also affect the communication speed and communication range of the scanner. 3. The prospective distance may vary based on environmental characteristics. Also note the following frequency description. 4. The frequency band of the electromagnetic radiation (2.4 GHz) used by this product is shared by various other devices. Therefore, baudrate and communication distance may be negatively impacted by other devices. Baudrate and communication distance are affected by obstacles, wave conditions, or a device at the other end. 5. This product is equipped with an antenna. Bringing this product too close to a metallic object may degrade performance.
18 Opticon PX-20 Specifications Manual 10. Cable and Connector 10.1. USB Cable A dedicated USB cable is provided. This cable has a USB-A connector on one end and a micro-USB B connector on the other end. 10.2. Connector Contact Number Signal Name 1 VCC 2 -DATA 3 +DATA 4 Ext trig 5 GND Figure 2: USB Micro-B connector 10.3. External trigger It is possible to trigger the PX-20’s barcode reader externally via a pin in the USB connector. The trigger is active low, edge triggered, enabled by grounding pin 4 in the USB connector.
19 Opticon PX-20 Specifications Manual 11. Labeling 11.1. Product label The product label shown below is affixed to the scanner. Figure 3: Product label The serial number consists out of 6 numeric digits. It starts with 000001 and is incremented with 1 for each scanner. The serial number is also stored in the scanners non-volatile memory and API functions are available to retrieve the serial number for use in user applications. Material: Base + laminate protection against wear. Base: PP film, thickness 80µm, backing with glue. Laminate: PET film, clear, thickness 50µm. Size: 25 x 18.5 mm. 11.1. White box label Size is 70mm x 25mm with a tolerance of ± 2 mm Label material: Paper, white, with permanent adhesive backing. Article number: Standard code 39 + human readable text , data = Jeeves number Serial number: Standard code 39 + human readable text, data should match that of the product inside the box. .
20 Opticon PX-20 Specifications Manual Figure 4: White box label
21 Opticon PX-20 Specifications Manual 12. Packaging Specifications 12.1. Individual Packaging Specification Put the scanner in a protective foam bag and place it in an individual packing box. Size of the package after assembly: 125 (W) x 112 (D) x 40 (H) mm Figure 5: Individual packaging
22 • •• • • ••••••• •••••••• 12.2.Collective Packaging Specification Size of the shipping box is: 500 0JV) x 560 (D) x 200 (H) mm Carton Box Pack 100 sets into the carton box A:Barcode seriallabelfor packing box B:Missing serialnumber label Stick the labels on both front and back side of the box Attach this label when more than two serialnumbers are out of sequence. C/No • a, Procb:t PX-20 PO: 1 ••••••• QTY: 1 ••••• SNJFrorn: lfl!lllllfll SNITO: IIHIII I IIIIIIHIII IIIIIIHI Mi &ing Serial number Q'ly •a. 1 IIPWJIIIJIIIfii IIJII·'II 2 1•11111111•1111•11•1•111•111•1 • C/No •• Missing Serialnumber Q'ly • • 3 JIIJIJIJIJIJ 4 1 •1••111•1•1•.•1•1 5 IJIJIJIJIJIJ 6 11•111111•11•1111•1111•111•111•111• 7 1111111flmliilJmJmJ• IIIIII 8 11•11111•11111•11111•11111•11111•11111•1111•1111 9 I IIIJIIIIJIIIJIIIIJIIIIJII IIIIII 10 11•11111•111•11•11•1111•111 111•11• ® Made in China Opticon Sensors Europe B.V. Made in China Opticon Sensors Europe B.V. Figure 6: Collective packaging Note: The "RO" mark labeled on the package tray or package box guarantees that the applicable product has passed our test of RoHS restrictions compliance (the restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC). However, this document does not have any legal weight in the European Union.
23 Opticon PX-20 Specifications Manual 13. Durability 13.1. Drop Test No malfunction occurred after the following drop test. Drop Test: Drop the data collector from a height of 180 cm onto a concrete floor (three times in each of 6 angles). Figure 7: Drop test
24 Opticon PX-20 Specifications Manual 14. Regulatory Compliance 14.1. Product Safety EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Lamp classification: IEC62471:2006 Exempt Group 14.2. EMC EN55022 EN55024 FCC Part 15 Subpart B Class B and Part 15 Subpart C: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example: Use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 14.3. REACH Regulation (EC1907/2006) compliance 14.4. RoHS RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC.
25 Opticon PX-20 Specifications Manual 14.5. R&TTE This scanner conforms to the following standards of the Radio and Telecommunications Terminal Equipment (R&TTE) directive from the EU. EN300 328 EN301 489
26 Opticon PX-20 Specifications Manual 15. Handling Handle this product carefully. Do not deliberately subject it to any of the following. 15.1. Shock Do not throw or drop the scanner. Do not drop or put heavy items on this product or its cable. 15.2. Temperature Conditions Do not use the scanner at temperatures outside the specified range. Do not use near heat sources such as radiators, heat registers, stoves, or other types of devices that produce heat. Do not use in areas exposed to direct sunlight for long periods of time. Do not pinch or forcibly bend the cable, especially at very low temperature. 15.3. Foreign Materials Do not immerse the scanner in liquids. Do not subject the scanner to chemicals. Do not insert foreign substances into the device. 15.4. Other Do not attempt to disassemble, modify or update this device. The scanner may not perform properly in environments when placed near a flickering light, such as a computer monitor, television, etc. Do not use in the reach of blinking lights such as CRT.
27 Opticon PX-20 Specifications Manual 16. Revision History Revision Date Issued By Comments 0.1 20120928 NiLe Initial revision 0.2 20121010 NiLe Changed chapter 10 to have micro USB 0.3 20121012 NiLe Updates during review 0.4 20121015 NiLe Updates according to review notes 0.5 20121030 NiLe Updated pictures 0.6 20121123 NiLe Updated label picture, Mech drawings 0.7 20121130 NiLe Updates during review 1.0 20121221 NiLe Version 1.0, updated according to comments from Ron de Vries 1.1 20130109 NiLe Re-added RoHS in certification chapter 1.2 20130125 Kees 1.3 20130530 NiLe Updated according to review by Ron de Vries. Mainly changing data from MDI-3100 HD version to MDI-3100 SR version

Navigation menu