Opticon Sensors Europe PX20 PX-20 User Manual PX20 datacollector

Download:
Mirror Download [FCC.gov]
Document ID	2141843
Application ID	PgZGqMXJxrvF10lH6v3NCg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78.39kB (979832 bits)
Date Submitted	2013-12-13 00:00:00
Date Available	2014-02-01 00:00:00
Creation Date	2013-11-29 08:53:40
Producing Software	Adobe PDF Library 10.0
Document Lastmod	2013-11-29 08:53:53
Document Title	PX20 datacollector
Document Creator	Acrobat PDFMaker 10.0 for Word
Document Author:	Niklas Lekselius

Portable 2D Data Collector
PX-20
The PX-20 is a portable data collector with a 2D barcode
scanner. Scanned and stored data can be transmitted to the
host via the USB interface, or via Bluetooth.
Specifications Manual
Opticon
PX-20
Specifications Manual
Preliminary. All information subject to change without notice.
Document History
Model Number:
PX-20
Edition:
1.3
Date:
2013-05-30
Copyright 2013 Opticon. All rights reserved.
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any
electronic or machine readable form without prior written consent of Opticon.
Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE
PRODUCT.
Serial Number
A serial number appears on all Opticon products. This official registration number is directly related to the device
purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the
warranty.
Warranty
Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and
workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in
materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by
modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under
warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect,
consequential or incidental damages arising out of use or inability to use both the hardware and software, even if
Opticon has been informed about the possibility of such damages.
Packaging
The packing materials are recyclable. We recommend that you save all packing material to use should you need to
transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered
by the warranty.
Trademarks
Trademarks used are the property of their respective owners.
Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 1217, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184
SUPPORT
USA
Europe
Phone: 800-636-0090
Email: support@opticonusa.com
Email: support@opticon.com
Web: www.opticonusa.com
Web: www.opticon.com
Opticon
PX-20
Specifications Manual
Contents
1. Abstract .....................................................................................................................................5
2. Overview ................................................................................................................................... 5
3. Physical Features ..................................................................................................................... 6
3.1. Dimensions ....................................................................................................................... 6
3.2. Weight ............................................................................................................................... 7
3.3. Color ................................................................................................................................. 7
4. Environmental Specifications.................................................................................................. 7
4.1. Operating Temperature and Humidity................................................................................ 7
4.2. Storage Temperature and Humidity ................................................................................... 7
4.3. Ambient Light Immunity ..................................................................................................... 7
5. Component Specification......................................................................................................... 8
6. Electrical Specifications........................................................................................................... 8
6.1. Absolute Maximum Ratings ............................................................................................... 8
6.2. Recommended Operating Conditions ................................................................................ 8
6.3. Electrical Characteristics ................................................................................................... 9
7. Optical Specifications ............................................................................................................ 10
8. Barcode reader Technical Specifications ............................................................................ 11
8.1. Bar Code Test Sample .................................................................................................... 12
8.2. Scan Area and Depth of Field.......................................................................................... 13
8.3. Print Contrast Signal........................................................................................................ 14
8.4. Minimum Resolution ........................................................................................................ 14
8.5. Wide Bar Code ................................................................................................................ 14
8.6. Motion Tolerance............................................................................................................. 15
8.7. Pitch, Skew, and Tilt ........................................................................................................ 16
8.8. Curvature ........................................................................................................................ 16
9. External interfaces.................................................................................................................. 17
9.1. USB-HID and USB-VCP Interface Specifications ............................................................ 17
9.2. Wireless Interface............................................................................................................ 17
10. Cable and Connector.............................................................................................................. 18
10.1. USB Cable ...................................................................................................................... 18
10.2. Connector........................................................................................................................ 18
10.3. External trigger ................................................................................................................ 18
11. Labeling................................................................................................................................... 19
11.1. Product label ................................................................................................................... 19
11.1. White box label ................................................................................................................ 19
Opticon
PX-20
Specifications Manual
12. Packaging Specifications....................................................................................................... 21
12.1. Individual Packaging Specification................................................................................... 21
12.2. Collective Packaging Specification .................................................................................. 22
13. Durability ................................................................................................................................. 23
13.1. Drop Test ........................................................................................................................ 23
13.2. Dust and water Proof ....................................................................................................... 23
14. Regulatory Compliance.......................................................................................................... 24
14.1. Product Safety................................................................................................................. 24
14.2. EMC ................................................................................................................................ 24
14.3. REACH............................................................................................................................ 24
Regulation (EC1907/2006) compliance..................................................................................... 24
14.4. RoHS .............................................................................................................................. 24
14.5. R&TTE ............................................................................................................................ 25
15. Handling .................................................................................................................................. 26
15.1. Shock .............................................................................................................................. 26
15.2. Temperature Conditions .................................................................................................. 26
15.3. Foreign Materials............................................................................................................. 26
15.4. Other ............................................................................................................................... 26
16. Revision History ..................................................................................................................... 27
Table of Figures
Figure 1: Dimensions .................................................................................................................. 6
Figure 2: USB Micro-B connector ............................................................................................. 18
Figure 3: Product label.............................................................................................................. 19
Figure 4: White box label .......................................................................................................... 20
Figure 5: Individual packaging .................................................................................................. 21
Figure 6: Collective packaging .................................................................................................. 22
Figure 7: Drop test .................................................................................................................... 23
Opticon
PX-20
Specifications Manual
1. Abstract
This manual provides specifications for the PX-20 portable 2D barcode data collector.
2. Overview
The PX-20 is a very compact data collector with a built-in 2D barcode scanner. Due to its
compact size and its Bluetooth capabilities, the PX-20 is the ideal companion scanner for
mobile devices like the iPhone/iPad and Android telephones and tablets. The supported
Bluetooth profiles are HID (keyboard emulation) and SPP (serial port emulation) Special
support is added for iOS devices that allows for the use of the on-screen keyboard, while
the PX-20 is connected. Additional to the Bluetooth wireless capabilities, the PX-20 also has
a 1MByte storage space for off-line use. The USB interface can then be used to download
the data. This is then again either as HID (keyboard emulation) or VCP (serial port
emulation). The PX-20 is fully programmable, using Opticon’s easy to use development
tools that are available for free.
Opticon
PX-20
Specifications Manual
3. Physical Features
3.1. Dimensions
(W) 36 x (L) 74 x (D) 16 mm
Figure 1: Dimensions
Opticon
PX-20
Specifications Manual
3.2. Weight
40 g (estimated)
3.3. Color
Black
4. Environmental Specifications
4.1. Operating Temperature and Humidity
Temperature: -10 to 50° C (Charging temperature range 0 to 45° C)
Humidity: 20% to 90% RH
4.2. Storage Temperature and Humidity
Temperature: -20 to 60° C
Humidity: 20% to 85% RH
4.3. Ambient Light Immunity
Decoding performance is guaranteed when the range of illumination on a barcode
surface is between zero and the following values:
Incandescent light
10,000 lx
Fluorescent light
10,000 lx
Sunlight
100,000 lx
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
Bar Code Sample
Distance
Angle
Curvature
Power Supply Voltage
: 0.33 mm UPC specified in Chapter 8
: 130 mm from the front edge of the camera module
: α = 0°, β =＋15°, γ = 0°
:R=∞
: 3.3 and 5.0 V
Note: α, β and γ respectively represent pitch, skew and tilt.
Opticon
PX-20
Specifications Manual
5. Component Specification
Item
Specifications
Notes
2D Engine
MDI-3100
Opticon’s 2D imager with integrated high speed decoder
Application
processor:
Renesas RX62N
96 MHz Clock speed
1 MByte serial flash
Barcode storage + >50,000 barcodes + time stamp. Might be used for
other purpose as well, depending on the users application.
512Kbyte program
flash
128Kbyte available for user applications
32Kbyte config flash
For configuration storage (e.g. Bluetooth link addresses)
RAM
96KByte
16Kbyte available for user applications
Keys
+ and -
Dome switches
LED
RGB
Bluetooth
CSR 8811
Flash ROM:
6. Electrical Specifications
6.1. Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Power supply voltage (VDD to GND)
VDD
-0.3 to 6.5
Input voltage
VIN
-0.5 to VDD +0.5
0.1 V p-p (10-100 kHz)
Power ripple
6.2. Recommended Operating Conditions
Item
Symbol
Power supply voltage
VDD
Input voltage
Vin
Conditions
Min
Typ
Max
Unit
Battery
3.5
4.2
Ｖ
USB
4.5
5.0
5.5
Ｖ
－
VDD
Ｖ
Opticon
PX-20
Specifications Manual
6.3. Electrical Characteristics
Parameter
Operating
current
Symbol
Typ
Max
Unit
While Scanning
IOP
350
400
mA
While in Standby
IPRE
45
50
mA
While Charging
ICHG1
350
400
mA
Ioff
100
150
μA
2.75
3.7
4.2
350
355
mAh
When OFF
Voltage
VBAT
Rated capacity
Battery
specifications
Min
Charging current
ICHG2
Charging time
Tchg
2.5
hour
Scans when fully charged *1
Operating time
1500
20
Times
Hours
Scans when fully charged *2
Operating time
2500
35
Times
Hours
Td
75
ms
Startup time (from deep sleep)
160
mA
Notes
*1 One scan of 1 second per minute, Bluetooth link active, data transmitted
immediately after the scan..
*2 One scan of 1 second per minute, Bluetooth link not active.
Opticon
PX-20
Specifications Manual
7. Optical Specifications
Item
Characteristics
Scan method
CMOS area sensor (black and white)
Nr of effective pixels
752 (H) x 480 (V)
Dots
Image capture speed (*1)
60 fps
Frames per second
Focal distance
130 mm
Horizontal
40.6°
Vertical
26.4°
View angle
Red LED
Auxiliary light source
(LED x 2)
Peak wave length
617nm
Directivity angle 2θ1/2 (*2)
60°
Maximum radiation output (*3)
15000mcd
Green LED
Light source for aiming
Peak wave length
528nm
Maximum radiation output (*3)
18700mcd
Notes:
*1 The fastest speed of image capture
*2 Typical value
*3 Typical value at 25 °C
10
Opticon
PX-20
Specifications Manual
8. Barcode reader Technical Specifications
Scanning is done by pointing the PX-20’s aiming light to the center of a bar code for scanning.
The conditions for technical specifications are as follows, unless otherwise specified in each section.

Ambient Temperature and Humidity
Ambient Light
Pitch Angle
Skew Angle
Tilt Angle
Curvature
Power Supply Voltage
PCS (1D and 2D)
Scanning Test
Bar Code Test Sample (1D and 2D)
: Room temperature and room humidity
: 100 ~200 lux (on the surface of a bar code)
: α= 0°
: β = 15°
: γ = 0°
:R=∞
: 3.3 and 5.0 V
: 0.9 or higher
: Accept the performance with 90% or more success
rate for 10 tries of scan. One scan should be tested
within 2 seconds.
: Specified below
< Test chart >
For 1D codes, OPTOELECTRONICS test samples
For GS1 Databar, stacked codes and 2D codes, printed by a dedicated printer for bar code
11
Opticon
PX-20
Specifications Manual
8.1. Bar Code Test Sample
1 D Bar Codes

Resolution
0.127 mm (5mil)
0.20 mm (7.9mil)
0.254 mm (10mil)
0.508 mm (20mil)
Symbology
PCS
Code 39
0.9

Resolution
0.20 mm (7.9mil)
Symbology
Code 128

Resolution
0.330 mm (13mil)

Resolution
0.15 mm (6mil)
Size (mm)
32 × 10
100 × 10
32.5 × 10
36 × 25
No. of Digits
15
31
PCS
0.9
Size (mm)
42 × 10
No. of Digits
16
Symbology
12-digit UPC
PCS
0.9/0.3
Size (mm)
31.5 × 25.0
No. of Digits
12
Symbology
Codabar
PCS
0.9
Size (mm)
20 × 10
No. of Digits
10
Symbology
Limited
Limited-Composite
PCS
0.9
0.9
Size (mm)
12 × 1.5
12 × 3.0
No. of Digits
14
26
Error Correction
PCS
No. of Character
Level-3
0.9
Size (mm)
23 × 10
35 × 15
Error Correction
PCS
No. of Character
0.9
Size (mm)
6×6
11 × 11
Model
PCS
No. of Character
ECC200
0.9
Size (mm)
5×5
GS1 Databar

Resolution
0.169 mm (6.7mil)
0.169 mm (6.7mil)
2 D Codes

Resolution
0.169 mm (6.7mil)
0.254 mm (10mil)

Resolution
0.212 mm (8.4mil)
0.381 mm (15mil)

Resolution
0.212 mm (8.4mil)
0.254 mm (10mil)
Note: The size is outline dimensions excluding quiet zone.
12
6×6
58
44
40
Opticon
PX-20
Specifications Manual
8.2. Scan Area and Depth of Field
The scan area is measured from the front edge of the camera module.
100
50
250
200
150
300
0.127(5mil)
90
Code 39
130
210
0.508(20mil)
* 65
Code 128
[ Unit ： mm ]
0.254(10mil)
70
0.20(7.9mil)
80
300
190
0.33(13mil)
UPC 100%
225
55
0.169(6.7mil)
85
145
PDF417
0.254(10mil)
65
200
0.212(8.4mil)
95
QR Code
0.381(15mil)
60
Data Matrix
120
80
0.254(10mil)
200
150
Note: The depth of field depends on the view angle and symbol length
13
Opticon
PX-20
Specifications Manual
Figure 3: Scan Area and Depth of Field
8.3. Print Contrast Signal
PSC 0.3 or higher

MRD
Distance
Bar Code Sample
: 32% and higher
(70% or higher reflectivity of space and quiet zone)
: 130 mm from the front edge of the camera module
: UPC specified in Chapter 8. (Resolution: 0.33 mm, PCS: 0.3)
MRD = Minimum reflectance of white bar - Maximum reflectance of black bar
PCS = Error!
8.4. Minimum Resolution
1D Code
GS1-Databar
Stacked Code
2D Code
: 0.127 mm (5 mil) Code 39 specified in Chapter 8
: 0.169 mm (6.7 mil) GS1 Databar-Limited specified in Chapter 8
: 0.169 mm (6.7 mil) PDF417, GS1 Databar-Limited Composite specified in Chapter 8
: 0.212 mm (8.4 mil) OR Code and Data Matrix specified in Chapter 8

Bar Code Sample
: The above codes specified in Chapter 8
Distance
: 100 mm from the front edge of the camera module
Angle
: α = 0°, β =＋15°, γ = 0°
Curvature
:R=∞
For the pitch angle and tilt angle measurement, set the skew angle β = +15°
8.5. Wide Bar Code
Code 39 with width of 100 mm and resolution of 0.2 mm can be read.

Bar Code Sample
Distance
Angle
Curvature
: 0.20 mm Code 39 specified in Chapter 8
: 160 mm from the front edge of the camera module
: α = 0°, β =＋15°, γ = 0°
:R=∞
Figure 4: Wide Bar Code
14
Opticon
PX-20
Specifications Manual
8.6. Motion Tolerance
UPC bar code 100% can be read when it is moving at 2m/s.

Ambient Temperature and Humidity
Ambient Light
Distance
Angles
Skew
Tilt
Curvature
Power Supply Voltage
PCS (1D and 2D)
Bar Code Sample
: Room temperature and Room humidity
: 500 lux to 1000 lux (on the surface of a bar code)
: 130 mm from the front edge of the camera module
: α= 0°
: β = 15°
: γ = 0°
:R=∞
: 3.3 and 5.0 V
: 0.9 or higher
: UPC with 0.33 mm resolution specified in Chapter 8
Figure 5: Motion Tolerance
Note: The above shows the possible speed of reading, but no guarantee of 100% reading.
: Scanning may fail due to the specular reflection of illumination LEDs when the reflectivity is high.
15
Opticon
PX-20
Specifications Manual
8.7. Pitch, Skew, and Tilt
Pitch
Skew
Tilt
: α = ±50°
: β = ±50°
: γ = ±180°

Bar Code Sample
: 0.33 mm UPC specified in Chapter 8
Distance
: 130 mm from the front edge of the camera module
Curvature
:R=∞
For the pitch angle and tilt angle measurement, set the skew angle β = +15°
α
β －
＋
－
＋
γ
＋
－
Figure 6: Pitch, Skew, and Tilt
8.8. Curvature
0.33 mm 12-digit UPC
0.15 mm 10-digit Codabar

Bar Code Sample
Distance
Angle
: R ≧ 20 mm
: R ≧ 16 mm
: 0.33 mm UPC specified in Chapter 8
: 110 mm from the front edge of the camera module
: α = 0°, β =＋15°, γ = 0°
Figure 7: Curvature
Note: Scanning may fail due to the specular reflection of illumination LEDs when the reflectivity is high.
16
Opticon
PX-20
Specifications Manual
Interface Specifications
9. External interfaces
9.1. USB-HID and USB-VCP Interface Specifications
Complies with USB Version 2.0. The supported profiles are USB-COM (also referred
to as USB-VCP that stands for Virtual Communication Port). This port is used for
charging and data communication.
9.2. Wireless Interface
PX-20 has a BT connection with the following features:
Feature
Description
Version 1)
2.1
Supported profiles 1)
SPP (Serial Port Profile)
HID (Human Interface Device Profile)
Scanner operating mode while
connected to the host system
Master or Slave mode
Security mode
As per the Bluetooth 2.1 specification. The settings for this can be
configured in the user application.
Encryption
Encryption is linked to the authentication setting and cannot be
enabled or disabled separately.
Communication range 3)
Approximately 10 meters
Frequency 4)
2400 MHz to 2483.5 MHz
Transmission power
2.5mW (4dBm) or less
Baud rate
115.2 kbps
Antenna 5)
Built in
Notes
1. This product complies with the Bluetooth 2.1 standard. The device that
communicates with this product must support either SPP or HID as well. For
other Bluetooth devices with other profiles we cannot guarantee a connection
before the products have been tested.
2. The communication speed and range of the product may vary due to obstacles
and radio wave conditions between this product and the device to which it is
connected. Conditions on the host device may also affect the communication
speed and communication range of the scanner.
3. The prospective distance may vary based on environmental characteristics.
Also note the following frequency description.
4. The frequency band of the electromagnetic radiation (2.4 GHz) used by this
product is shared by various other devices. Therefore, baudrate and
communication distance may be negatively impacted by other devices.
Baudrate and communication distance are affected by obstacles, wave
conditions, or a device at the other end.
5. This product is equipped with an antenna. Bringing this product too close to a
metallic object may degrade performance.
17
Opticon
PX-20
Specifications Manual
10. Cable and Connector
10.1. USB Cable
A dedicated USB cable is provided. This cable has a USB-A connector on one end
and a micro-USB B connector on the other end.
10.2. Connector
Contact
Number
Signal Name
VCC
-DATA
+DATA
Ext trig
GND
Figure 2: USB Micro-B connector
10.3. External trigger
It is possible to trigger the PX-20’s barcode reader externally via a pin in the USB
connector. The trigger is active low, edge triggered, enabled by grounding pin 4 in the
USB connector.
18
Opticon
PX-20
Specifications Manual
11. Labeling
11.1. Product label
The product label shown below is affixed to the scanner.
Figure 3: Product label
The serial number consists out of 6 numeric digits. It starts with 000001 and is incremented
with 1 for each scanner. The serial number is also stored in the scanners non-volatile
memory and API functions are available to retrieve the serial number for use in user
applications.
Material: Base + laminate protection against wear.
Base: PP film, thickness 80µm, backing with glue.
Laminate: PET film, clear, thickness 50µm.
Size: 25 x 18.5 mm.
11.1. White box label
Size is 70mm x 25mm with a tolerance of ± 2 mm
Label material: Paper, white, with permanent adhesive backing.
Article number: Standard code 39 + human readable text , data = Jeeves number
Serial number: Standard code 39 + human readable text, data should match that of the
product inside the box.
19
Opticon
PX-20
Specifications Manual
Figure 4: White box label
20
Opticon
PX-20
Specifications Manual
12. Packaging Specifications
12.1. Individual Packaging Specification
Put the scanner in a protective foam bag and place it in an individual packing box.
Size of the package after assembly: 125 (W) x 112 (D) x 40 (H) mm
Figure 5: Individual packaging
21
12.2.Collective Packaging Specification
Size of the shipping box is: 500 0JV) x 560 (D) x 200 (H) mm
Carton Box
Pack 100 sets into the carton box
A:Barcode seriallabelfor packing box
Stick the labels on both front and back side of the box
C/No •
B:Missing serialnumber label
Attach this label when more than two serialnumbers are
out of sequence.
a,
C/No ••
Missing Serialnumber Q'ly • •
Procb:t
PX-20
PO:
1 •••••••
• ••••••
1 •••••
• ••
QTY:
•
•
lfl!lllllfll
SNJFrorn:
I IHI
IIHII I IIIIIHIII III
SNITO:
••••••••
Mi &ing Serial number Q'ly •a.
I JIIIfii
IIPWJI
IIJII·'II
11
111111
1111 11111111
10
JIIJIJIJIJIJ
1 1 111 1 1 .11
••• • • •••
IJIJIJIJIJIJ
111
1111111
1111111111
11
•• ••••••
1111111flmliilJmJmJ• IIIIII
1111111111111111111111111111111111111111
I IIIJIIIJIIIJIIIJIIIJII IIIIII
1111111111111111111111
••••••••
••• •••••
•••• ••••
Made in China
Opticon Sensors Europe B.V.
Made in China
®
Opticon Sensors Europe B.V.
Figure 6: Collective packaging
Note: The "RO" mark labeled on the package tray or package box guarantees that the
applicable product has passed our test of RoHS restrictions compliance (the
restriction of the use of certain hazardous substances in electrical and electronic
equipment, 2002/95 EC). However, this document does not have any legal weight in
the European Union.
22
Opticon
PX-20
Specifications Manual
13. Durability
13.1. Drop Test
No malfunction occurred after the following drop test.
Drop Test: Drop the data collector from a height of 180 cm onto a concrete floor (three
times in each of 6 angles).
Figure 7: Drop test
23
Opticon
PX-20
Specifications Manual
14. Regulatory Compliance
14.1. Product Safety
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
Lamp classification: IEC62471:2006 Exempt Group
14.2. EMC
EN55022
EN55024
FCC Part 15 Subpart B Class B and Part 15 Subpart C: This device complies with
part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to
operate this equipment. (Example: Use only shielded interface cables when
connecting to computer or peripheral devices).
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
14.3. REACH
Regulation (EC1907/2006) compliance
14.4. RoHS
RoHS: The restriction of the use of certain hazardous substances in electrical and
electronic equipment, 2002/95 EC.
24
Opticon
PX-20
Specifications Manual
14.5. R&TTE
This scanner conforms to the following standards of the Radio and
Telecommunications Terminal Equipment (R&TTE) directive from the EU.
EN300 328
EN301 489
25
Opticon
PX-20
Specifications Manual
15. Handling
Handle this product carefully. Do not deliberately subject it to any of the following.
15.1. Shock
Do not throw or drop the scanner.
Do not drop or put heavy items on this product or its cable.
15.2. Temperature Conditions
Do not use the scanner at temperatures outside the specified range.
Do not use near heat sources such as radiators, heat registers, stoves, or other types
of devices that produce heat.
Do not use in areas exposed to direct sunlight for long periods of time.
Do not pinch or forcibly bend the cable, especially at very low temperature.
15.3. Foreign Materials
Do not immerse the scanner in liquids.
Do not subject the scanner to chemicals.
Do not insert foreign substances into the device.
15.4. Other
Do not attempt to disassemble, modify or update this device.
The scanner may not perform properly in environments when placed near a flickering
light, such as a computer monitor, television, etc. Do not use in the reach of blinking
lights such as CRT.
26
Opticon
PX-20
Specifications Manual
16. Revision History
Revision
Date
Issued By
0.1
20120928
NiLe
0.2
20121010
NiLe
0.3
20121012
NiLe
0.4
20121015
NiLe
0.5
20121030
NiLe
0.6
20121123
NiLe
0.7
20121130
NiLe
1.0
20121221
NiLe
1.1
20130109
NiLe
1.2
20130125
Kees
1.3
20130530
NiLe
Comments
Initial revision
Changed chapter 10 to have micro USB
Updates during review
Updates according to review notes
Updated pictures
Updated label picture, Mech drawings
Updates during review
Version 1.0, updated according to comments from Ron de
Vries
Re-added RoHS in certification chapter
Updated according to review by Ron de Vries. Mainly
changing data from MDI-3100 HD version to MDI-3100 SR
version
27

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Niklas Lekselius
Create Date                     : 2013:11:29 08:53:40+01:00
Modify Date                     : 2013:11:29 08:53:53+01:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2013:11:29 08:53:53+01:00
Creator Tool                    : Acrobat PDFMaker 10.0 for Word
Document ID                     : uuid:f1a25db8-b093-472c-83d1-18950fc15ed2
Instance ID                     : uuid:15897e8e-c8d7-4da2-b6ef-1b3a764704ec
Subject                         : 2
Format                          : application/pdf
Title                           : PX20 datacollector
Creator                         : Niklas Lekselius
Producer                        : Adobe PDF Library 10.0
Source Modified                 : D:20131129075318
Company                         : HP
Created                         : D:20131017
Last Saved                      : D:20131125
Page Layout                     : OneColumn
Page Count                      : 27