Oracle America PWRFID LCD Pole Display w/RFID Series 2 User Manual User Guide

Download:
Mirror Download [FCC.gov]
Document ID	2190862
Application ID	q++byFFUZN2/R3WGEjz/OA==
Document Description	A4HPWRFID_User Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.85kB (98087 bits)
Date Submitted	2014-02-15 00:00:00
Date Available	2014-02-17 00:00:00
Creation Date	2013-09-27 09:48:41
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2013-10-31 16:02:35
Document Title	Microsoft Word - User Guide.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ljliang

Key Information
The new designed MICROS customer display implements the NFC function.
The Rear Display is attached to MICROS POS docking station- mStation.
The Pole Display stands alone the mStation. Except the normal display
function, both new models have NFC function.
Specification
Model
Overall Dimension (not including
mounting fixture)
LCD module size
Backlight
Number of character
Power in
Rating
Max. Operating Temperature
NFC Function
LCD Rear Display w/RFID Series 2
LCD Pole Display w/RFID Series 2
63.2 x 135.9 x 29.3mm
37 x 116 x12.9mm
LED Backlight
20CH x 2 Lines
DC 5V from mStation customer display port
DC 5V, 250mA max.
65°C
YES
Product final location
Installing of LCD Pole Display w/RFID Series 2
As above picture shown, fix the position of the pole display (beside the
mStation), and connect the cable to mStation customer display port.
Installing of LCD Rear Display w/RFID Series 2
The following procedure describes how to attach the Rear LCD Customer
Display (LCD Rear Display Series 2) to the MICROS mStation.
The customer display is provided as a complete assembly ready to install.
1. Remove the AC power cable from the mStation.
2. Place the mStation face down. Find the 2 screw holes for attach LCD
customer display, which at the edge of unit.
3. Attach the LCD customer display to it and tighten the captive screws as
shown in figure 1.
Tighten the captive screws
Customer
Display
mStation
Figure 1
4. Feed the interface cable to IO port labeled “Customer Display”
5. Snap-in the cable to the clip and rubber footer. And then use cable tie to
fix the cable inside the concave as shown in figure 2.
Clip
Rubber
footer
Cable tie to fix
the cable in
concave
Figure 2
6. Return the mStation to the normal operating position, connect the AC
power cord and press the power button. The Integrated LCD Customer
Display is automatically detected.
Figure 3
Test the Customer Display
1. From the Window Embedded Compact 7 Desktop, go to MyDevice >
Boot > Utilities > Diagutility_Vienna. The[Micros Diagnostic] screen
displayed.
2. Press the “Customer Display” icon,
• Select display data
•
Click [Send] or [Full Update] button
3. The text message displayed on the customer display screen.
4. NFC function
•
Put the card near the rear display or pole display
•
Display NFC antenna will sense the card and transfer the data to
the mTablet.
Caution:
This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Page Count                      : 4
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:54473a9e-8722-4306-a77c-93a2ef64f5c3
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:10:31 16:02:35+08:00
Create Date                     : 2013:09:27 09:48:41+08:00
Metadata Date                   : 2013:10:31 16:02:35+08:00
Document ID                     : uuid:976d8cb1-8264-4b72-b67a-f166790bfa13
Format                          : application/pdf
Title                           : Microsoft Word - User Guide.doc
Creator                         : ljliang
Author                          : ljliang

EXIF Metadata provided by EXIF.tools