Ox Co OVS01 Vehicle detection sensor User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	2941140
Application ID	dZwm2+gbzpYY1hi8FS+43w==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.54kB (831780 bits)
Date Submitted	2016-03-24 00:00:00
Date Available	2016-09-21 00:00:00
Creation Date	2016-02-10 09:36:28
Producing Software	Acrobat Distiller 10.1.16 (Windows)
Document Lastmod	2016-02-10 09:37:16
Document Title	Users manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	n-kageyama

VEHICLE DETECTION SENSOR
OVS-01 BG / BGB
OVS-01 CC / CCB
OVS-01 PK / PKB
for BARRIER GATE
for CAR COUNTING
for PARKING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC WARNING(For USA)
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
-NOTICEThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
-NOTICE1.The antennas cannot be exchanged.
2.To comply with FCC RF exposure compliance requirements, aseparation distance of at least 20cm must be
maintained between the antenna of this device and all persons.
Vehicle Detection Sensor OVS-01 series
1) Product Line-Up
Type designation
Application
OVS-01BG
OVS-01BGB
Barrier Gate
OVS-01CC
OVS-01CCB
Car Counting
OVS-01PK
OVS-01PKB
Parking
OVS-01BG Operation Panel
OVS-01CC Operation Panel
OVS-01 PK Operation Panel
Select
Button
Select
Button
Indicator
Select
Button
Select
Button
Select
Button
2) Specifications
Item
1 Power Supply
2 Current Draw
3 Output
4 MW detection Range
5 Ultrasonic Detection Range
7 Mode
Sensitivity
OVS-01BGB
0.8 - 8m
OVS-01CCB
OVS-01CC
5 level (1,2,3,4,5)
selectable by Select button
OVS-01PKB
OVS-01PK
DC12-24V±10%
Heater ON：150mA max. (Heater Off： 80mA max.)
2(Two) outputs ( Output １/ Output ２ ) 1a Relay output 30V, 0.3A
0.8 - 5.5m
0.1 - 1.5m Fixed
0.8 - 3m
Default 3
Anti Bump Sensitivity
Anti Bump Timer
0.5,1.0, 2.0, 4.0sec selectable by Select button
Default 2 sec
0.5,1.0, 2.0, 4.0sec selectable by Select button
Default 2 sec
Off Delay
0.5,1.0, 2.0, 4.0sec selectable by Select button
Default 2 sec
0.5,1.0, 2.0, 4.0sec selectable by Select button
Default 2 sec
On Delay
0.5,1.0, 2.0, 4.0sec selectable by Select button
Default 2 sec
Output 1 NO/NC select
Output 2 Relay/Trouble
Maximum Range
（MW）
Behavior Type
Location
Human cancel
Calibration
Area Check
Response Time
Operating temperature
Operating Humidity
Protection Category
15 Sensor Aiming Adjust
16
17
18
19
20
21
OVS-01BG
Off, Low, Mid. High selectable by Select button
Default Mid.
Re-detection Timer
10
11
12
13
14
Calibration Area Check
Button
Button
Detection Speed
Reset
Frequency
Indicator
Narrow Lens
Radio approved standard
NO / NC selectable by select button Default NO
Output 2 NO / Output 2 NC / Trouble output NO / Trouble output NC selectable by Select button Default Output 2 NO
8 level (2, 2.5, 3, 3.5, 4, 4.5, 6, 8m)
8 level (2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5m)
8 level (2.4, 2.6, 2.8, 3, 3.2, 3.4, 3.6, 3.8m)
selectable by Select button Default 4m
selectable by Select button Default 4m
selectable by Select button Default 3.2m
Activation / Vehicular Protection
selectable by Select button
Corner / Center
selectable by Select button
Equipped
By Calibration button
By Area Check button
500ms
500ms
300ms
-30 〜50℃
93% max.
IP65
Pan : ±30°
Pan : ±15°
Pan : ±30°
Pan : ±15°
Pan : ±30°
Pan : ±15°
Tilt：Not available
Tilt：Not available
Tilt：Not available
Tilt：Not available
Tilt：Not available
Tilt：Not available
60km/h max.
20km/h max.
20km/h max.
Back to default, Press one sec. " Area Check " and " Calibration " button same time
MW : 24GHz, Ultrasonic : 58KHz
3 (Three) color LED Standby :Green, Area check : Not detect Green flashing, Detect Red, Calibration : Blue flashing
Equipped
Equipped
FCC Parts 15 Subpart C:2013, ARIB STD-T73 1.2 and R & TTE
3) Installation
OVS-01BG / BGB
1. Install the Base to
Square Pillar or Wall
3. Adjust Sensor Angle,
Maximum Range and
Behavior Type
2. Wiring
4. Calibration
Press the Calibration button
Indicator
*Blue LED flashing (8 sec.).
*Blue LED fast flashing (2 sec.)
*Blue LED to Green LED
*Completed
5. Area Check
Press the Area Check button
6. Set the Parameter
Indicator
*Green LED flashing
*Red flashing when detecting Human,
Vehicle Test pole
*Press the Area Check button or
Wait for 30 sec. with Green LED flashing
*Completed
Anti Bump Sensitivity
Anti Bump Timer
Off Delay
Output 2
Output 1
7. System Check
8. Put the Cover
OVS-01CC / CCB
1. Install the Base to
Square Pillar or Wall
3. Adjust Sensor Angle
and Maximum Range
2. Wiring
4. Calibration
Press the Calibration button
Indicator
*Blue LED flashing (8 sec.).
*Blue LED fast flashing (2 sec.)
*Blue LED to Green LED
*Completed
5. Area Check
Press the Area Check button
6. Set the Parameter
Indicator
*Green LED flashing
*Red flashing when detecting Human,
Vehicle Test pole
*Press the Area Check button or
Wait for 30 sec. with Green LED flashing
*Completed
7. System Check
8. Put the Cover
Off Delay
Output 2
Output 1
OVS-01PK / PKB
1. Install the Base to
Square Pillar or Wall
3. Adjust Sensor Angle
and Maximum Range
2. Wiring
4. Calibration
Press the Calibration button
Indicator
*Blue LED flashing (8 sec.).
*Blue LED fast flashing (2 sec.)
*Blue LED to Green LED
*Completed
5. Area Check
Press the Area Check button
Indicator
*Green LED flashing
*Red flashing when detecting Human,
Vehicle Test pole
*Press the Area Check button or
Wait for 30 sec. with Green LED flashing
*Completed
6. Set the Parameter
Off Delay
Output 2
Output 1
7. System Check
8. Put the Cover
4) How to check the Detection Area
For the detection area checking, we recommend to use diameter 60mm pole (Height around 1m～1.5m) as standard.
Example
Bar
Assumed
Loop Coil area
(LC1)
Assumed
Loop Coil area
(LC2)
[3]
[1]
[5]
[4]
[2]
Checking Pole
OVS-01BG
Behavior Position :Activation
OVS-01BG
Behavior Position : Safety
1. Press the Area Check button
2. Check the Indicator turn to Green flashing
7. Check the checking pole to near the Bar [ 5 ]
8. Check the Indicator turn to Green LED flashing
(Not detect pole)
Area Check
button
3. Put the Checking Pole to corner of assumed loop coil area [ 1 ]
4. Leave from detection area
5. Check the indicator turn to Red flashing
9. Press the Area Check button or wait for
30 sec. With Green LED flashing
10. Completed.
6. Repeat 3-5 for [ 2 ] [ 3 ] and [ 4 ]
Checking Pole
Example
[1]
Bar
[2]
S1
OVS-01BG
1. Press the " Area Check " button
2. Check the indicator turn on to Green LED flashing.
7. Check the checking pole to near the Bar [ 2 ]
8. Check the Indicator turn to Green LED flashing
(Not detect pole)
(keep Green flashing)
Area Check
button
3. Put the checking pole to expected area Top [ 1 ]
4. Leave from detection area
5. Check the indicator turn to Red flashing
9. Press the Area Check button or wait for
30 sec. With Green LED flashing
10. Completed.
Other Precaution
1. The detection area of Ultrasonic sensor should not contact with anything,
(the ground, flower pot, the box etc.)
Example
-5°OK. (Detection area is not
contacting with the ground)
-15°NG. (Detection area is contacting
with the ground)
Ground
Ground
Detection area of Ultrasonic Sensor
2. Mounting Height 60-80cm will have 100% performance.
3. Sensitivity Level (Human detection and Vehicle detection)
The following are relation between Human cancel and Vehicle detection.
Position 3 is used generally.
Sensitivity
Sensitivity
High
Low
Not detect
100% not detect
Two-Tree Human One Human
High
Low
Around 92-95%
not detect one Human
Vehicle Detection
around 99.999%
Vehicle Detection Vehicle Detection
around 99.9%
around 97%
Vehicle Detection
Human Cancel
4. Anti-Bump function
Anti Bump Sensitivity
Off
Low
Mid
Hig
Anti Bump Time
0.5
1.0
2.0
4.0
Generally, Anti Bump Sensitivity position use " Off " position. Anti Bump Time function does not work in the Off position.
However, If more safety is required to avoid the Bar contact with Vehicle, Anti-Bump function will be used.
* General Application : Anti-Bump Function ( Sensitivity : Off)
Gate Bar
S2
Ticket
Machine
S1
S2
Ticket
Machine
Gate Bar
S1
S2
Ticket
Machine
S1
Ticket
Machine
Gate Bar
S2
S1
Gate Bar
OVS-01BG
OVS-01BG
Gate Bar is down
Gate Bar is Up
Gate Bar is going down
Gate Bar is Down
* Use Anti Bump Function (Sensitivity Mid )
Gate Bar
Gate Bar
Gate Bar
OVS-01BG
S2
Ticket
Machine
S1
S2
S1
Ticket
Machine
S2
Ticket
Machine
S1
In this case, Bar have to be up
immediately to avoid contacting
with Vehicle.
OVS-01BG
Gate Bar is going down
Gate Bar is Up
Suddenly Vehicle comes back
by slop etc.
Note
S2
Leave from the detection area
S2
5)
* After Vehicle leave from the detection area,
Sensitivity is more sensitive for 0.5 or 1 or 2 or 4 sec. (selectable by Anti-Bump timer).
(During Anti Bump function is working, Human cancel function dose not work.)
* Sensitive level is selected. (Low, Mid. High ). Generally Mid position is used.
Note : Anti Bump function works in the only Behavior position "Safety"
5. Off Delay Timer
0.5
Off delay
Selectable Off delay time ( 0.5, 1, 2, 4 second)
MW Detection Area
OVS-01Sensor
OVS -01 Sensor
On
Off
0.5 sec.
Relay Output
ON
Off
Off Delay time
Off Delay time
6. Calibration
* Calibration must be definitely executed after installation.
* Calibration must be executed with stable parking condition..
It mean there are no Vehicle, human, Big plant pot and Box etc within the detection area
when calibration is executed.
Parking
MW Detection
Good !
Bad !
OVS-01
Calibration Button
OVS-01
Sensor
7. Heater
・MW dose not work if snow is stuck to the surface of Ratome..
Radome
・Purpose of Heater is to melt the snow that is stuck to the surface of Redame.
・Heater will work when outside temperature become around 0 degree
automatically.
Radome surface keep around 4 degree or more by this heater.
Snow is not stuck to surface of radome of 4 degree or more
1. Rain becomes snow if temperature becomes less 0 ℃.
2. 0 ℃ must be guaranteed because it is operating temperature range.
3. Heater which is attached to rear surface of radome solves this problem.
4. Heater dose not warm the electrical components inside OVS-01
5. Limit -20 degree is defined by the specification of MW, Ultrasonic
Radome
MW module
Radome
MW module
Heater
Radome
MW module
Snow
Snow
OK!
No!
OK!
8. Detection Area
Ultrasonic Detection Area
250
Horizontal
150
100
100
50
50
Z [cm]
200
150
Y [cm]
200
-50 0
100
200
300
400
500
-50 0
-100
-100
-150
-150
-200
-200
-250
Vertical
250
100
-250
X [cm]
MW area with Narrow Lens
・OVS-01BG / BGB
This model dose not equip the narrow lens.
200
300
400
500
X [cm]
MW area without Narrow Lens
・OVS-01CC / CCB / PK / PKB
This model equip the narrow lens.
9. MW and Ultrasonic
・OVS-01 series equips MW and Ultrasonic sensor.
・Presence detection is possible by FMCW.
・Ultrasonic Sensor detect near side range.
・Detection logic
①MW detect a car first.
②When MW detect a car, Ultrasonic can be possible to detect.
③Output is OR gate of MW and Ultrasonic sensor.
MW sensor
detection area
Ultrasonic sensor
detection area
*Car is detected by MW sensor first.
*When MW detect a car, Ultra sonic
sensor
can be possible to detect
MW sensor
detection area
Ultrasonic sensor
detection area
Human is not detected
Human is not detected
Car is detected by Ultrasonic sensor
10. Output
* All OVS-01 series equips six terminals
Power Supply
DC12-24V
Relay 1
output
Relay 2
output
Output 1
Output 2 (Sub output)
(Main output)
or
Trouble output
Select "Output 2 Relay / Trouble "
by Select Button A
Select NO or NC by Button
Indicator
(Red)
Select Button A
Button
Indicator
(Green)
Select Trouble Output by Button B
Select Output 2 by Button B
Select Button B
Select
Button B
Indicator
(Green)
Indicator
(Green)
Select R.N.O or R.N.C by Select Button B
Select T.N.O or T.N.C by Select Button B
Indicator
(Green)
Select Button B
Indicator
Select
Button B
Trouble Output
When either MW or Ultrasonic sensor
is failed (dead), it is outputted.
However, This output do not understand
that either Sensor is failed (dead).

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : n-kageyama
Create Date                     : 2016:02:10 09:36:28+09:00
Modify Date                     : 2016:02:10 09:37:16+09:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Title                           : OVS-01 取説_20160210.xlsx
Creator                         : n-kageyama
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2016:02:10 09:37:16+09:00
Producer                        : Acrobat Distiller 10.1.16 (Windows)
Document ID                     : uuid:dae12eeb-3a2d-4af4-bd3f-6a2c5d5d2f44
Instance ID                     : uuid:e4242efb-0b13-4fa8-b9f2-3ebf0d2c2946
Page Count                      : 8

EXIF Metadata provided by EXIF.tools