PAC PAC-FP Door access controller User Manual Users manual

PAC International Limited Door access controller Users manual

Users manual

International Ltd.1 Park Gate Close, Bredbury,Stockport, SK6 2SZ, EnglandTel: +44 (0) 161 406 3400Fax: +44 (0) 161 430 8658INTERNATIONAL Data SheetNovember 1999PAC 2200 Series and PAC 2100 Series Programming Panel InstructionsReader 16 character display48 Key Keypad1.5m Flying LeadDescriptionThe PAC 2100 Series and PAC 2200 Series of door controllers are programmed from a panelattached to the front of the controller. This panel consists of a 48 key keypad, a 16 characterdisplay and a KeyPAC proximity key administration reader. This front panel is commonly fittedwhen the controller is a Master controller (System Types 0, 1 and 2). However when used as aSlave controller (System Type 3) then, apart from initial programming, the panel is unnecessary.
PAC 2200 Series and PAC 2100 Series Programming Panel 170XX Ver 1.0©1999 PAC DRAFT 2How to Use the Programming PanelNote: You should follow the instructions provided in the manuals for the controller being used(17113 PAC 2100/1100 Installation Manual and 17112 PAC 2100/1100 User Manual or 17263PAC 2200 Series Controllers Installation Manual and 17267 PAC 2200 Series Controllers UserManual) for full details on programming these door controllers.-V+VGND+5vBAT++18vGND+12vCHANNEL 1CHANNEL 2GNDSIGDR1DR2DR3DR4LED+18VL- L+ GNDSIGDR1DR2DR3DR4LED+18VL- L+ CHANNEL 3GNDSIGDR1DR2DR3DR4LED+18VL- L+ CHANNEL 4GNDSIGDR1DR2DR3DR4LED+18VL- L+ F1F3F2F4SW2BATTERYF5RESETSW1PL1CN7RELAYS TAMPER SIX WIRE BUS PRINTER +V AB1AB2DSDUSD -V GNDDTR RXCTS TXT+ T- F+ F- CM NO NC CM NO NC CM NO NC CM NO NCPower SupplyFront Panel ConnectorREMOVAL OF THIS COVERINVALIDATES WARRANTYBaseplateWARNING!Figure 1 - Location of Front Panel Connector for PAC 2100 Series ControllersR ESETSIX W IRE BUS +V A B1 AB2 D SD US D -VCTS TXRXGNDSP AR ECTSTXRXGNDPR IN TER/RS 232RTSF-F+T-T+TA M P ER O VER RIDE+12VBAT++18VGND +5VGND +V -VR e lay 2COM NO NC R e lay 4COM NO NCR e lay 5COM NO NCR e lay 6COM NO NCR e lay 7COM NO NCR e lay 8COM NO NCR e lay 3COM NO NCR e lay 1COM NO NC12V/24VAU X 0VB- B+B a tte ryGN DSIG 1DCDR1RTEDR2DR3D R4 LED+ 18VL- L+ Rdr1Rde2SIG 2 Lock 1Reader 1GN DSIG 1DCDR1RTEDR2DR3D R4 LED+ 18VL- L+ Lock 2GN DSIG 1DCDR1RTEDR2DR3D R4 LED+ 18VL- L+ Rdr1Rde2SIG 2 Lock 3GN DSIG 1DCDR1RTEDR2DR3D R4 LED+ 18VL- L+ Lock 4Reader 2Reader 3Reader 4Front Panel ConnectorPower SupplyBaseplateFigure 2 - Location of Front Panel Connector for PAC 2200 Series Controllers
PAC 2200 Series and PAC 2100 Series Programming Panel 170XX Ver 1.0©1999 PAC DRAFT 3To use the Programming Panel:1. Remove power from the door controller, not forgetting to disconnect any batteries as well.2. Connect the flying lead from the panel as follows: Into the socket at the top left of the door controller circuit board, just above the orangepower supply connector, for the PAC 2100 Series Controllers (Figure 1). Theconnector is keyed and will only fit in the correct orientation. Into the socket at the top right of the door controller circuit board for the PAC 2200 SeriesControllers (Figure 2). The connector is keyed and will only fit in the correctorientation.3. Power up the door controller again.You will now be able to use the front panel in accordance with the instructions in the relevantInstallation and User Manuals.Remove power from the door controller before disconnecting the panel.Warning: Take care not to allow the Programming Panel to drop, pulling the connector from thedoor controller socket.This device complies with part 15 of the FCC rules. Operation is subject to the followingtwo conditions (1) this device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may cause undesiredoperation.FCC ID OQL-PAC-FP

Navigation menu