PAC PAC-FP Door access controller User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	89838
Application ID	iFmlibptSbA0A5+HR/2W/g==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	53.49kB (668673 bits)
Date Submitted	2000-03-07 00:00:00
Date Available	2000-05-04 00:00:00
Creation Date	2000-03-07 07:35:36
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2000-03-07 07:35:38
Document Title	Users manual

Data Sheet
INTERNATIONAL
November 1999
PAC 2200 Series and PAC 2100 Series
Programming Panel Instructions
1.5m Flying Lead
Reader
16 character display
48 Key Keypad
Description
The PAC 2100 Series and PAC 2200 Series of door controllers are programmed from a panel
attached to the front of the controller. This panel consists of a 48 key keypad, a 16 character
display and a KeyPAC proximity key administration reader. This front panel is commonly fitted
when the controller is a Master controller (System Types 0, 1 and 2). However when used as a
Slave controller (System Type 3) then, apart from initial programming, the panel is unnecessary.
International Ltd.
1 Park Gate Close, Bredbury,
Stockport, SK6 2SZ, England
Tel: +44 (0) 161 406 3400
Fax: +44 (0) 161 430 8658
PAC 2200 Series and PAC 2100 Series
Programming Panel
170XX Ver 1.0
How to Use the Programming Panel
Note: You should follow the instructions provided in the manuals for the controller being used
(17113 PAC 2100/1100 Installation Manual and 17112 PAC 2100/1100 User Manual or 17263
PAC 2200 Series Controllers Installation Manual and 17267 PAC 2200 Series Controllers User
Manual) for full details on programming these door controllers.
Front Panel Connector
Power Supply
CHANNEL 1
GND
SIG
PL1
F1
REMOVAL OF THIS COVER
INVALIDATES WARRANTY
DR1
DR2
LED
+18V
DR3
DR4
L-
-V
+V
L+
GND
+5v
CHANNEL 2
GND
SIG
GND
+18v
BAT+
DR1
DR2
+12v
F2
CN7
LED
+18V
DR3
DR4
LL+
CHANNEL 3
GND
WARNING!
RESET
SW1
SIG
DR1
F3
BATTERY
F5
DR2
LED
+18V
DR3
DR4
LL+
CHANNEL 4
F4
GND
SIG
DR1
DR2
LED
SW2
RELAYS
TAMPER
SIX WIRE BUS
CM NO NC CM NO NC CM NO NC CM NO NC T+ T- F+ F-
PRINTER
+V AB1AB2DSDUSD -V GNDDTR RXCTS TX
+18V
DR3
DR4
LL+
Baseplate
Figure 1 - Location of Front Panel Connector for PAC 2100 Series Controllers
Front Panel Connector
R e lay 3
CO M
NO
R e lay 4
C NO C M
NO
R e a d er 1
R e a d er 2
R e a d er 3
NC
R e lay 5
CN OC M
NO
R e lay 6
C NO C M
NO
R e lay 7
CN OC M
NO
R e a d er 4
R e lay 2
CN OC M
NO
R T ED C
L o ck 2
R T ED C
S IG 2 L o ck 1
L + L - D R 4D R +3 1 8 VL E D D R 2D R 1S IG 1G N D R d e 2R d r1L + L - D R 4D R +3 1 8 VL E D D R 2D R 1S IG 1G N D
1 2 V /2 4 V R e lay 1
NO
A U X 0 VC O M
R e lay 8
CN OC M
NO
NC
RTED C
L o ck 4
R T ED C
S IG 2 L o ck 3
L + L - D R 4D R +3 1 8 VL E D D R 2 D R 1S IG 1G N D R d e 2R d r1L + L - D R 4D R +3 1 8 VL E D D R 2D R 1S IG 1G N D
BB+
B a tte ry
+ 1 2 VB A T + 1 8 V G N D + 5 V G N D + V
-V
Power Supply
TA M P ER
O V E R R ID ES IX W IR E B U S
SP AR E
P R IN T E R /R S 2 3 2
T+ T- F+ F- + V
A B 1 A B 2 D S D GU SN DDR X -V
C T S T X G N DR T S R X C T S T X
R ESET
Baseplate
Figure 2 - Location of Front Panel Connector for PAC 2200 Series Controllers
PAC 2200 Series and PAC 2100 Series
Programming Panel
170XX Ver 1.0
To use the Programming Panel:
1.
Remove power from the door controller, not forgetting to disconnect any batteries as well.
2.
Connect the flying lead from the panel as follows:
Into the socket at the top left of the door controller circuit board, just above the orange
power supply connector, for the PAC 2100 Series Controllers (Figure 1). The
connector is keyed and will only fit in the correct orientation.
Into the socket at the top right of the door controller circuit board for the PAC 2200 Series
Controllers (Figure 2). The connector is keyed and will only fit in the correct
orientation.
3.
Power up the door controller again.
You will now be able to use the front panel in accordance with the instructions in the relevant
Installation and User Manuals.
Remove power from the door controller before disconnecting the panel.
Warning: Take care not to allow the Programming Panel to drop, pulling the connector from the
door controller socket.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
FCC ID OQL-PAC-FP

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2000:03:07 07:35:36
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2000:03:07 07:35:38-05:00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools