PAC PAC-FP Door access controller User Manual Users manual

PAC International Limited Door access controller Users manual

Users manual

International Ltd.
1 Park Gate Close, Bredbury,
Stockport, SK6 2SZ, England
Tel: +44 (0) 161 406 3400
Fax: +44 (0) 161 430 8658
INTERNATIONAL Data Sheet
November 1999
PAC 2200 Series and PAC 2100 Series
Programming Panel Instructions
Reader 16 character display
48 Key Keypad
1.5m Flying Lead
Description
The PAC 2100 Series and PAC 2200 Series of door controllers are programmed from a panel
attached to the front of the controller. This panel consists of a 48 key keypad, a 16 character
display and a KeyPAC proximity key administration reader. This front panel is commonly fitted
when the controller is a Master controller (System Types 0, 1 and 2). However when used as a
Slave controller (System Type 3) then, apart from initial programming, the panel is unnecessary.
PAC 2200 Series and PAC 2100 Series
Programming Panel 170XX Ver 1.0
©1999 PAC DRAFT 2
How to Use the Programming Panel
Note: You should follow the instructions provided in the manuals for the controller being used
(17113 PAC 2100/1100 Installation Manual and 17112 PAC 2100/1100 User Manual or 17263
PAC 2200 Series Controllers Installation Manual and 17267 PAC 2200 Series Controllers User
Manual) for full details on programming these door controllers.
-V
+V
GND
+5v
BAT+
+18v
GND
+12v
CHANNEL 1
CHANNEL 2
GND
SIG
DR1
DR2
DR3
DR4
LED
+18V
L-
L+
GND
SIG
DR1
DR2
DR3
DR4
LED
+18V
L-
L+
CHANNEL 3
GND
SIG
DR1
DR2
DR3
DR4
LED
+18V
L-
L+
CHANNEL 4
GND
SIG
DR1
DR2
DR3
DR4
LED
+18V
L-
L+
F1
F3
F2
F4
SW2
BATTERY
F5
RESET
SW1
PL1
CN7
RELAYS TAMPER SIX WIRE BUS PRINTER
+V AB1AB2DSDUSD -V GNDDTR RXCTS TXT+ T- F+ F- CM NO NC CM NO NC CM NO NC CM NO NC
Power Supply
Front Panel Connector
REMOVAL OF THIS COVER
INVALIDATES WARRANTY
Baseplate
WARNING!
Figure 1 - Location of Front Panel Connector for PAC 2100 Series Controllers
R ESET
SIX W IRE BUS
+V A B1 AB2 D SD US D -VCTS TXRXGND
SP AR E
CTSTXRXGND
PR IN TER/RS 232
RTSF-F+T-T+
TA M P ER O VER RIDE
+12VBAT++18VGND +5VGND +V -V
R e lay 2
COM NO NC R e lay 4
COM NO NC
R e lay 5
COM NO NC
R e lay 6
COM NO NC
R e lay 7
COM NO NC
R e lay 8
COM NO NC
R e lay 3
COM NO NC
R e lay 1
COM NO NC
12V/24V
AU X 0V
B- B+
B a tte ry
GN DSIG 1
DC
DR1
RTE
DR2DR3D R4 LED+ 18VL- L+ Rdr1Rde2
SIG 2 Lock 1
Reader 1
GN DSIG 1
DC
DR1
RTE
DR2DR3
D R4 LED+ 18VL-
L+
Lock 2
GN DSIG 1
DC
DR1
RTE
DR2DR3D R4 LED+ 18VL- L+ Rdr1Rde2
SIG 2 Lock 3
GN DSIG 1
DC
DR1
RTE
DR2DR3
D R4 LED+ 18VL-
L+
Lock 4
Reader 2Reader 3
Reader 4
Front Panel Connector
Power Supply
Baseplate
Figure 2 - Location of Front Panel Connector for PAC 2200 Series Controllers
PAC 2200 Series and PAC 2100 Series
Programming Panel 170XX Ver 1.0
©1999 PAC DRAFT 3
To use the Programming Panel:
1. Remove power from the door controller, not forgetting to disconnect any batteries as well.
2. Connect the flying lead from the panel as follows:
Into the socket at the top left of the door controller circuit board, just above the orange
power supply connector, for the PAC 2100 Series Controllers (Figure 1). The
connector is keyed and will only fit in the correct orientation.
Into the socket at the top right of the door controller circuit board for the PAC 2200 Series
Controllers (Figure 2). The connector is keyed and will only fit in the correct
orientation.
3. Power up the door controller again.
You will now be able to use the front panel in accordance with the instructions in the relevant
Installation and User Manuals.
Remove power from the door controller before disconnecting the panel.
Warning: Take care not to allow the Programming Panel to drop, pulling the connector from the
door controller socket.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
FCC ID OQL-PAC-FP

Navigation menu