PBE Europe as Axell Wireless 50-1465SERIES 50-146501 VHF Channelised Air Interface User Manual 50 146501 50 146601 50 146701HBKM

Axell Wireless 50-146501 VHF Channelised Air Interface 50 146501 50 146601 50 146701HBKM

Contents

User Manual 1 of 2

Aerial Facilities Limited Technical Literature  Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM Issue No. A  Date:15/10/2006 Page 1 of 86 Aerial Facilities Limited New York Justice Centre Radio Repeater Equipment ForGPD Telecom Inc. AFL Works Order:   Q114828 AFL product part Nǀs.: 50-146501 (VHF Repeater)      50-146601 (UHF Repeater)      50-146701 (800MHz Repeater)
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 2 of 86 Table of Contents 1. INTRODUCTION ............................................................................................................5Scope and Purpose of Document.................................................................................................... 5Limitation of Liability Notice ............................................................................................................ 52. SAFETY CONSIDERATIONS ........................................................................................62.1 Earthing of Equipment......................................................................................................... 62.2 Electric Shock Hazard.......................................................................................................... 62.3 RF Radiation Hazard ............................................................................................................ 62.4 Chemical Hazard .................................................................................................................. 72.5 Laser Safety.......................................................................................................................... 72.6 Emergency Contact Numbers ............................................................................................. 73. EQUIPMENT OVERVIEW ..............................................................................................83.1 System Description.............................................................................................................. 83.2 Whole System Diagram, Drg. # 50-146581 ......................................................................... 94. SYSTEM DETAILS.......................................................................................................104.1 VHF Channel Selective Cell Enhancer Rack (50-146501) ............................................... 104.1.1 VHF Cell Enhancer Rack Description .............................................................................. 104.1.2 VHF Cell Enhancer Rack Electrical Specification ............................................................ 104.1.3 VHF Cell Enhancer Rack Mechanical Specification......................................................... 114.1.4 VHF Cell Enhancer Rack Parts List ................................................................................. 114.1.5 VHF Downlink O/P Combiner Shelf (50-146502) ............................................................. 124.1.5.P VHF Downlink O/P Combiner Shelf Photographs...................................................................124.1.5.1 Description ..............................................................................................................................134.1.5.2 Technical Specification ...........................................................................................................134.1.6.3 Parts List .................................................................................................................................134.1.5.4 System Diagram, Drg. # 50-146582 .......................................................................................144.1.6 VHF Uplink I/P Splitter Shelf (50-146503)........................................................................ 154.1.6.P VHF Uplink I/P Splitter Shelf Photographs..............................................................................154.1.6.1 Description ..............................................................................................................................164.1.6.2 Technical Specification ...........................................................................................................164.1.6.3 Parts List .................................................................................................................................164.1.6.4 System Diagram, Drg. # 50-146583 .......................................................................................174.1.7 VHF Duplex BDA Channel 1 Shelf (50-146504) .............................................................. 184.1.7.P VHF Duplex BDA Channel 1 Shelf Photographs ....................................................................184.1.7.1 Description ..............................................................................................................................194.1.7.2 Technical Specification ...........................................................................................................194.1.7.3 Parts List .................................................................................................................................204.1.7.4 System Diagram, Drg. # 50-146584 .......................................................................................214.1.8 VHF Duplex BDA Channel 2 Shelf (50-146505) .............................................................. 224.1.8.P VHF Duplex BDA Channel 2 Shelf Photographs ....................................................................224.1.8.1 Description ..............................................................................................................................224.1.8.2 Technical Specification ...........................................................................................................224.1.8.3 Parts List .................................................................................................................................224.1.8.4 System Diagram......................................................................................................................234.1.9 VHF Simplex BDA Channel 3A Shelf (50-146506) .......................................................... 244.1.9.P VHF Simplex BDA Photographs .............................................................................................244.1.9.1 Description ..............................................................................................................................254.1.9.2 Technical Specification ...........................................................................................................254.1.9.3 System Diagram, Drg. # 50-146586 .......................................................................................264.1.9.4 Parts List .................................................................................................................................274.1.10 VHF Simplex BDA Channel 3B Shelf (50-146507) .......................................................... 284.1.10.P VHF Simplex BDA Channel 3B Photographs .........................................................................284.1.10.1 Description ..............................................................................................................................284.1.10.2 Technical Specification ...........................................................................................................284.1.10.3 System Diagram, Drg. # 50-146587 .......................................................................................294.1.10.4 Parts List .................................................................................................................................304.1.11 VHF Simplex BDA Channel 4 Shelf (50-146508)............................................................. 314.1.11.P VHF Simplex BDA Channel 4 Shelf Photographs ..................................................................314.1.11.1 Description ..............................................................................................................................31
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 3 of 86 4.1.11.2 Technical Specification ...........................................................................................................314.1.11.3 System Diagram, Drg. # 50-146588 .......................................................................................324.1.11.4 Parts List .................................................................................................................................334.1.12 Downlink I/P Splitter (50-146509).....................................................................................344.1.12.P Downlink Input Splitter Photographs.......................................................................................344.1.12.1 Description ..............................................................................................................................354.1.12.2 Technical Specification ...........................................................................................................354.1.12.3 Parts List .................................................................................................................................354.1.12.4 System Diagram, Drg. # 50-146589 .......................................................................................364.1.13 Downlink O/P Combiner (50-146510) ..............................................................................374.1.13.P Downlink O/P Combiner Photographs ....................................................................................374.1.13.1 Description ..............................................................................................................................384.1.13.2 Technical Specification ...........................................................................................................384.1.13.3 Parts List .................................................................................................................................384.1.13.4 System Diagram......................................................................................................................394.1.14 VHF/UHF 24V Power Supply Shelf (50-146512) ............................................................. 404.1.14.P VHF/UHF Power supply Shelf Photographs ...........................................................................404.1.14.1 VHF/UHF PSU Shelf Description............................................................................................414.1.14.2 VHF/UHF PSU Shelf Technical Specification .........................................................................414.1.14.3 VHF/UHF PSU Shelf Parts List ...............................................................................................424.1.14.4 VHF/UHF PSU Shelf System Diagram, (needs new drawing) ...............................................434.2 UHF Channel Selective Cell Enhancer Rack (50-146601) ............................................... 444.2.1 Description ....................................................................................................................... 444.2.2 Electrical Specification ..................................................................................................... 444.2.3 Mechanical Specification.................................................................................................. 444.2.4 Parts List .......................................................................................................................... 454.2.5 Downlink Combiner Shelf (50-146602) ............................................................................ 464.2.5.P Downlink Combiner Photographs ...........................................................................................464.2.5.1 Description ..............................................................................................................................474.2.5.2 Technical Specification ...........................................................................................................474.2.5.3 Parts List .................................................................................................................................474.2.5.4 System Diagram, Drg. # 50-146682 .......................................................................................484.2.6 Uplink Splitter Shelf (60-146603) ..................................................................................... 494.2.6.P Uplink Splitter Shelf Photographs ...........................................................................................494.2.6.1 Description ..............................................................................................................................504.2.6.2 Technical Specification ...........................................................................................................504.6.2.3 Parts List .................................................................................................................................504.2.6.4 System Diagram, Drg. # 50-146683 .......................................................................................514.2.7 UHF Duplex Channel 1 BDA (50-146604) ....................................................................... 524.2.7.P Duplex Shelf Photographs (hardware identical, only 1 shelf shown)......................................524.2.7.1 Description ..............................................................................................................................534.2.7.2 Technical Specification ...........................................................................................................534.2.7.3 Parts List .................................................................................................................................544.2.7.4 UHF Duplex Channel 1 BDA System Diagram Drg. # 60-146684..........................................554.2.8 UHF Duplex Channel 2 BDA (50-146605) ....................................................................... 564.2.8.1 UHF Duplex Channel 2 BDA System Diagram, Drg. # 50-146685.........................................564.2.9 UHF Duplex Channel 3 BDA (50-146606) ....................................................................... 574.2.9.1 UHF Duplex Channel 3 BDA System Diagram, Drg. # 50-146686.........................................574.2.10 UHF Duplex Channel 4 BDA (50-146607) ....................................................................... 584.2.10.1 UHF Duplex BDA Channel 4 System Diagram, Drg. # 50-146687.........................................584.2.11 UHF Duplex Channel 5 BDA (50-146608) ....................................................................... 594.2.11.1 UHF Duplex Channel 5 System Diagram, Drg. # 50-146688 .................................................594.2.12 UHF Duplex Channel 6 BDA (50-146612) ....................................................................... 604.2.12.1 UHF Duplex Channel 6 BDA System Diagram, Drg. # 50-146692.........................................604.2.13 UHF Uplink Combiner Shelf (50-146609)......................................................................... 614.2.13.P UHF Uplink Combiner Shelf Photographs ..............................................................................614.2.13.1 Description ..............................................................................................................................624.2.13.2 Technical Specification ...........................................................................................................624.2.13.3 Parts List .................................................................................................................................624.2.13.4 UHF Uplink Combiner Shelf System Diagram, Drg. # 50-146689..........................................634.2.14 UHF Downlink Splitter Shelf (50-146610) ........................................................................ 644.2.14.P UHF Downlink Splitter Shelf Photographs ..............................................................................644.2.14.1 Description ..............................................................................................................................654.2.14.2 Technical Specification ...........................................................................................................65
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 4 of 86 4.2.14.3 Parts List .................................................................................................................................654.2.14.4 UHF Downlink Splitter Shelf System Diagram, Drg. # 50-146690..........................................664.3 800MHz Channel Selective Cell Enhancer Rack (50-146701) ......................................... 674.3.1 Description ....................................................................................................................... 674.3.2 Technical Specification..................................................................................................... 674.3.3 Parts List .......................................................................................................................... 674.3.4 800MHz Channel Selective C.E. System Diagram, Drg. # 50-146782............................. 684.4 Channel Selective Uplink & Downlink Shelf (50-146702)................................................ 694.4.P Uplink & Downlink Shelf Photographs.............................................................................. 694.4.1 Uplink & Downlink Shelf Description ................................................................................ 704.4.2 Uplink & Downlink Shelf Electrical Specifications ............................................................ 704.4.3 Uplink & Downlink Shelf Mechanical Specifications......................................................... 704.4.4 Uplink & Downlink Shelf System Diagram See section 4.3.4........................................... 704.4.5 Uplink & Downlink Shelf Parts List ................................................................................... 714.5 800MHz Downlink Power Amplifier Shelf (50-146703) .................................................... 724.5.P Downlink Power Amplifier Shelf Photographs .................................................................. 724.5.1 Downlink Power Amplifier Shelf Description ....................................................................734.5.2 Downlink Power Amplifier Shelf Electrical Specifications................................................. 734.5.3 Downlink Power Amplifier Shelf Mechanical Specification............................................... 734.5.4 Downlink Power Amplifier Shelf System Diagram............................................................ 734.5.5 Downlink Power Amplifier Shelf Parts List .......................................................................744.6 Multiband Combiner Shelf (50-146705) ............................................................................ 754.6.P Multiband Combiner Shelf Photographs........................................................................... 754.6.1 Multiband Combiner Shelf Description ............................................................................. 764.6.2 Multiband Combiner Shelf Technical Specification .......................................................... 764.6.3 Multiband Combiner Shelf Parts List ................................................................................ 764.6.4 Multiband Combiner Shelf System Diagram, Drg. # 50-146785....................................... 775. INSTALLATION............................................................................................................785.1 Initial Installation Record................................................................................................... 786. FAULT FINDING & MAINTENANCE ...........................................................................786.1 General Fault Finding Procedures.................................................................................... 785.2 Downlink ............................................................................................................................. 795.3 Uplink .................................................................................................................................. 795.4 Fault repair.......................................................................................................................... 795.5 Checking service................................................................................................................ 795.6 Service Support.................................................................................................................. 795.7 Tools & Test Equipment .................................................................................................... 795.8 General Maintenance Procedures .................................................................................... 805.9 Module Removal (LNAs, general procedure)................................................................... 805.10 Module Replacement (general) ......................................................................................... 805.11 Power Amplifiers ................................................................................................................ 805.12 Low Power Amplifier Replacement .................................................................................. 815.13 Module Transportation ...................................................................................................... 81APPENDIX A......................................................................................................................... 82Amendment List Record Sheet...................................................................................................... 82Glossary of Terms........................................................................................................................... 83Key to AFL Drawing Symbols ........................................................................................................ 84EC Declaration of Conformity ........................................................................................................ 85APPENDIX B......................................................................................................................... 86Initial Equipment Set-Up Calculations ..........................................................................................86General Information........................................................................................................................ 86Antenna Systems ........................................................................................................................... 86Initial Parameters ........................................................................................................................... 86Downlink Calculations .................................................................................................................... 86Uplink Calculations......................................................................................................................... 86
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 5 of 86 1. INTRODUCTION Scope and Purpose of Document This handbook is for use solely with the equipment identified by the AFL Part Number shown on the front cover. It is not to be used with any other equipment unless specifically authorised by Aerial Facilities Limited. This is a controlled release document and, as such, becomes a part of Aerial Facilities’ Total Quality Management System. Alterations and modification may therefore only be performed by Aerial Facilities Ltd. AFL recommends that the installer of this equipment familiarise themselves with the safety and installation procedures contained within this document before installation commences. The purpose of this handbook is to provide the user/maintainer with sufficient information to service and repair the equipment to the level agreed. Maintenance and adjustments to any deeper level must be performed by AFL, normally at the company’s repair facility in Chesham, England. This handbook has been prepared in accordance with BS 4884, and AFL’s Quality procedures, which maintain the company’s registration to BS EN ISO 9001:2000 and to the R&TTE Directive of the European Parliament. Copies of the relevant certificates and the company Quality Manual can be supplied on application to the Quality Manager. This document fulfils the relevant requirements of Article 6 of the R&TTE Directive. Limitation of Liability Notice This manual is written for the use of technically competent operators/service persons. No liability is accepted by AFL for use or misuse of this manual, the information contained therein, or the consequences of any actions resulting from the use of the said information, including, but not limited to, descriptive, procedural, typographical, arithmetical, or listing errors. Furthermore, AFL does not warrant the absolute accuracy of the information contained within this manual, or its completeness, fitness for purpose, or scope. AFL has a policy of continuous product development and enhancement, and as such, reserves the right to amend, alter, update and generally change the contents, appearance and pertinence of this document without notice. All AFL products carry a twelve month warranty from date of shipment. The warranty is expressly on a return to base repair or exchange basis and the warranty cover does not extend to on-site repair or complete unit exchange.
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 6 of 86 2. SAFETY CONSIDERATIONS 2.1  Earthing of Equipment Cell Enhancers supplied from the mains must be connected to grounded outlets and earthed in conformity with appropriate local, national and international electricity supply and safety regulations. 2.2  Electric Shock Hazard Electrical shocks due to faulty mains driven power supplies. Whilst ever potentially present in any electrical equipment, such a condition would be minimised by quality installation practice and thorough testing at: a) Original assembly   b) Commissioning   c) Regular intervals, thereafter. All test equipment to be in good working order prior to its use. High current power supplies can be dangerous because of the possibility of substantial arcing. Always switch off during disconnection and reconnection.2.3  RF Radiation Hazard RF radiation, (especially at UHF frequencies) arising from transmitter outputs connected to AFL’s equipment, must be considered a safety hazard. This condition might only occur in the event of cable disconnection, or because a ‘spare’ output has been left un-terminated. Either of these conditions would impair the system’s efficiency. No investigation should be carried out until all RF power sources have been removed. This would always be a wise precaution, despite the severe mismatch between the impedance of an N type connector at 50, and that of free space at 377, which would severely mitigate against the efficient radiation of RF power. Radio frequency burns could also be a hazard, if any RF power carrying components were to be carelessly touched! Antenna positions should be chosen to comply with requirements (both local & statutory) regarding exposure of personnel to RF radiation. When connected to an antenna, the unit is capable of producing RF field strengths, which may exceed guideline safe values especially if used with antennas having appreciable gain. In this regard the use of directional antennas with backscreens and a strict site rule that personnel must remain behind the screen while the RF power is on, is strongly recommended. Where the equipment is used near power lines or in association with temporary masts not having lightning protection, the use of a safety earth connected to the case-earthing bolt is strongly advised.
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 7 of 86 2.4 Chemical Hazard Beryllium Oxide, also known as Beryllium Monoxide, or Thermalox™, is sometimes used in devices within equipment produced by Aerial Facilities Ltd. Beryllium oxide dust can be toxic if inhaled, leading to chronic respiratory problems. It is harmless if ingested or by contact. Products that contain beryllium are load terminations (dummy loads) and some power amplifier transistors. These products can be identified by a yellow and black “skull and crossbones” danger symbol (shown above). They are marked as hazardous in line with international regulations, but pose no threat under normal circumstances. Only if a component containing beryllium oxide has suffered catastrophic failure, or exploded, will there be any danger of the formation of dust. Any dust that has been created will be contained within the equipment module as long as the module remains sealed. For this reason, any module carrying the yellow and black danger sign should not be opened. If the equipment is suspected of failure, or is at the end of its life-cycle, it must be returned to Aerial Facilities Ltd for disposal. To return such equipment, please contact the Quality Department, who will give you a Returned Materials Authorisation (RMA) number. Please quote this number on the packing documents, and on all correspondence relating to the shipment. PolyTetraFluoroEthylene, (P.T.F.E.) and P.T.F.E. Composite Materials Many modules/components in AFL equipment contain P.T.F.E. as part of the RF insulation barrier. This material should never be heated to the point where smoke or fumes are evolved. Any person feeling drowsy after coming into contact with P.T.F.E. especially dust or fumes should seek medical attention.2.5 Laser Safety General working practices adapted from EN60825-2: 2000 “Do not stare with unprotected eyes or with any unapproved optical device at the fibre ends or connector faces or point them at other people.” “Use only approved filtered or attenuating viewing aids.” “Any single or multiple fibre end or ends found not to be terminated (for example, matched, spliced) shall be individually or collectively covered when not being worked on. They shall not be readily visible and sharp ends shall not be exposed.”  “When using test cords, the optical power source shall be the last connected and the first disconnected.” “Use only approved methods for cleaning and preparing optical fibres and optical connectors.” Always keep optical connectors covered to avoid physical damage Do not allow any dirt/foreign material ingress on the optical connector bulkheads. The optical fibre jumper cable maximum bend radius is 3cm; any smaller radii may result in optical cable breakage or excessive transmission losses. Note: Not all AFL products use fibre optic units and they are NOT weather proof. 2.6  Emergency Contact Numbers The AFL Quality Department can be contacted on: Telephone   +44 (0)1494 777000 Fax    +44 (0)1494 777002 E-mail qa@aerialfacilities.com
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 8 of 86 3. EQUIPMENT OVERVIEW 3.1 System Description The New York Justice Centre needs three different frequency bands of radio coverage within its designated areas, each having specific channel allocations, some of which are simplex type, i.e. Tx & RX on a single frequency, and some duplex where the Tx & Rx are on two different frequencies so that both parties may transmit (or receive) simultaneously. The AFL equipment supplied for this task is in several different parts: VHF Channel selective Cell Enhancer    150MHz band, 5 channels (50-146501) UHF Channel Selective Cell Enhancer    400MHz band, 6 channels (50-146601) 800MHz Channel Selective Cell Enhancer    800MHz band, 2 channels (50-146701) Multi-Band Combiner          All three frequency bands (80-146705) All the cell enhancers have two switched attenuators in each path, a 0-30dB device to adjust the signal level entering the channel selective module, and a 0-15dB unit which varies the output power (after the channel module) that drives the leaky feeder antennas. In this way the system may be finely tuned to both receive and transmit at the correct levels. Each cell enhancer will be described separately in this document but where enhancers have common modules, these will be detailed only once. An alarm system is fitted that monitors all active devices and is easily integrated into any series ‘loop’ type system (where any break will trigger an alarm and show a local fault LED in the area where the fault originated).
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 9 of 86 3.2  Whole System Diagram, Drg. # 50-146581
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 10 of 86 4. SYSTEM DETAILS 4.1  VHF Channel Selective Cell Enhancer Rack (50-146501) 4.1.1 VHF Cell Enhancer Rack Description The VHF cell enhancer, built into ten 19” wide shelves and housed in a 43U high equipment rack, is a mixture of simplex (Tx & Rx on one frequency) and duplex (Tx & Rx on two separate frequencies) systems, three simplex and two duplex. There are separate Rx and Tx antennæ for the VHF and UHF bands and a composite antenna for the 800MHz bi-directional system. All VHF input channels, up and downlink are selected by narrow band crystal filters, and all outputs have ferrite isolators fitted in series to increase the isolation between adjacent channels and protect the transistors of the power stages from possibly damaging reflections. Each active module has a volt-free relay contact pair alarm which is looped to provide a normally-closed system. The inputs and outputs are handled by combining and splitting shelves and the channel processing and amplification is all within the BDA channel shelves. The simplex Tx/Rx system relies upon noise-free paths to enable accurate detection and muting to occur and for this reason it is not recommended to disturb these circuits as they are carefully set up by AFL when system tested and should not be adjusted except by expert personnel. A dedicated power supply shelf provides the DC needed by the VHF system, (a similar power supply is used in the UHF system also), and all alarms are volt-free relay contact pairs, looped in each shelf to provide a summary alarm with local failure indicator, suitable for integration into any such existing system. No battery backup is provided for this system and so should the mains supply fail, this system could not function. 4.1.2 VHF Cell Enhancer Rack Electrical Specification PARAMETER SPECIFICATION153.965MHz* (Ch. 1) 154.755MHz154.785MHz154.980MHz158.925MHz* (Ch. 2) VHF downlink 151.355MHz* (Ch. 1) 154.6575MHz* (Ch. 2) 154.755MHz154.785MHzVHF Frequencies:154.980MHzVHF uplink Bandwidth: 15kHz (up & downlink) Downlink Gain(Duplexed): 97 dB min Downlink Gain(Simplex): 97 dB min Uplink Gain (Duplex & Simplex): 100 dB min Gain Adjustment: 0 – 15dB (in 1dB step) Uplink Power: >2-5Watts Downlink Power: >10Watts AGC: Fitted in all channel selective modules Noise Figure: <6dB (@ maximum gain) VSWR: better than 1.5:1 Impedance: 50ȍRF Connectors: N type, female Supply voltage: 110V AC (nominal) @ 43-63Hz System power requirement: 24V DC @ <13A 1 Amplifiers Alarms Fitted: (volt-free contacts/TTL)  2 PSU * = duplex channel
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 11 of 86 4.1.3 VHF Cell Enhancer Rack Mechanical Specification PARAMETER SPECIFICATIONHeight: 43U Standard Eldon Vented Rack Width: 19" (482.6mm) RackDepth: 600mm Height: See parts lists Width: 19" (482.6mm) ShelvesDepth: <450mm(excluding heatsinks, connectors, handles and feet) operational: -20°C to +60°C Temperaturerange storage: -40°C to +70°C Weight: >100kg Relative humidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Supply cable: Unit supplied from PSU shelf Case: Iridite NCP coat Heatsinks: None Handles: Silver anodised aluminium alloy FinishFascia: Painted to RAL7035 4.1.4 VHF Cell Enhancer Rack Parts List AFL Part #  Part Description  Qty. 50-146502  VHF DOWNLINK O/P COMBINER  1 50-146503  VHF UPLINK I/P SPLITTER  1 50-146504  VHF DUPLEX BDA CHN 1  1 50-146505  VHF DUPLEX BDA CHN 2  1 50-146506  VHF SIMPLEX BDA CHN 3A  1 50-146507  VHF SIMPLEX BDA CHN 3B  1 50-146508  VHF SIMPLEX BDA CHN 4  1 50-146509  VHF DOWNLINK I/P SPLITTER  1 50-146510  VHF UPLINK O/P COMBINER  1 50-146512  VHF/UHF SYSTEM PSU 24V  1 80-054020  600mm DEEP SUPPORT BRACKET  20 80-063654  1U BLANKING PANEL (BS) RAL 7035  7 80-063655  2U BLANKING PANEL (BS) RAL 7035  2 90-100011  IEC MAINS LEAD '6 AMP' for USA  1 91-000002  N PLUG RG223:U  30 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  4 97-500175  ELDON 43U 600 x 600 RACK (VENTED LID)  1 99-000082  PALLET 900 x 900 x 7ply FOR RACKS  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 12 of 86 4.1.5 VHF Downlink O/P Combiner Shelf (50-146502) 4.1.5.P  VHF Downlink O/P Combiner Shelf Photographs
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 13 of 86 4.1.5.1DescriptionThe five (downlink) channels are received from the output ports of the individual bi-directional amplifier shelves and coupled together through hybrids, except for channel 2 which, being a substantially higher frequency than the other four, has its own path through a dedicated bandpass filter at the output of which the other four combined frequencies and channel 2 meet. The single signal path is then passed through a divider to two equal level downlink output ports, VHF1 & VHF2. This is a passive shelf and has no connection to the PSU and no alarms 4.1.5.2Technical Specification PARAMETER SPECIFICATIONHeight: 3U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg Frequency ranges passed: 153.965 to 154.980 & 158.925MHz Impedance: 50ȍHumidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Case: Iridite NCP coat Heatsinks: None Handles: Silver anodised aluminium alloy FinishFascia: Painted to RAL7035 4.1.6.3Parts List AFL Part #  Part Description  Qty. 01-003105  SD NOTCH FILT.N 6 SECT.VHF H/B SMA  2 05-000101  TRANSMITTER HYBRID COUPLER (4 PORT)  1 05-000103  TX HYBRID COUPLER 3 PORT (NO HEATSINK)  3 19-000922K  3U CHASSIS KIT (450mm deep)  1 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  8 91-130001  SMA ADAPT 'T' ALL FEMALE 3 GHz  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 14 of 86 4.1.5.4System Diagram, Drg. # 50-146582
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 15 of 86 4.1.6 VHF Uplink I/P Splitter Shelf (50-146503) 4.1.6.P   VHF Uplink I/P Splitter Shelf Photographs
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 16 of 86 4.1.6.1DescriptionThis shelf receives the single uplink RF from the antenna(s) and, similar to the downlink, one of the five channels is substantially different in frequency to the other four. This means that channel 1 is routed through a dedicated bandpass filter and the other four signals together also use a single filter. The output of this ‘four-way’ signal path is then split to four individual crystal filters, which, together with channel 1 path form the five uplink inputs to the five VHF amplifying shelves. Channel 1 signal needs no crystal filter as its single bandpass filter is tuned to a much narrower bandwidth to the filter in the other path containing the ‘four’ frequencies. This is a passive shelf and has no connection to the PSU and no alarms 4.1.6.2Technical Specification PARAMETER SPECIFICATIONHeight: 3U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg Frequency ranges passed: 153.965 to 154.980 & 158.925MHz Impedance: 50ȍHumidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Case: Iridite NCP coating Heatsinks: None Handles: Silver anodised aluminium alloy FinishFascia: Painted to RAL7035 4.1.6.3Parts List AFL Part #  Part Description  Qty.01-003105  SD NOTCH FILT.N 6 SECT.VHF H/B SMA  2 19-000922K  3U CHASSIS KIT (450mm deep)  1 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  6 91-130001  SMA ADAPT 'T' ALL FEMALE 3 GHz  4 93-980195  154.755MHz CRYSTAL FILT FAN4M52500  1 93-980196  154.785MHz CRYSTAL FILT FAN4M52500  1 93-980197  154.980MHz CRYSTAL FILT FAN4M52500  1 93-980198  154.6575MHz CRYSTAL FILT FAN4M52500  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 17 of 86 4.1.6.4System Diagram, Drg. # 50-146583
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 18 of 86 4.1.7 VHF Duplex BDA Channel 1 Shelf (50-146504) 4.1.7.P  VHF Duplex BDA Channel 1 Shelf Photographs As all the duplex shelves are hardware similar, only this pair of duplex shelf photographs are shown.
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 19 of 86 4.1.7.1DescriptionThe two duplex bi-directional amplifier shelves receive a downlink signal from the input antenna, amplify it to a level suitable for processing by a channel selective module and send the resultant 10W power signal to its designated antenna. The uplink path is very similar but in reverse with only a  five Watt RF output power. Both paths feature a ferrite isolator on the output to prevent damage to the power amplifier should any reflected signals occur at their output antenna ports. 4.1.7.2Technical Specification PARAMETER SPECIFICATIONHeight: 3U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg 153.956MHz (Ch. 1)Downlink channel frequency: 158.925MHz (Ch. 2) 151.355MHz (Ch. 1) Uplink channel frequency: 154.6575MHz (Ch. 2) Shelf gain: 100dB (typical) Impedance: 50ȍHumidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Case: Iridite NCP coating Heatsinks: Black anodised Handles: Silver anodised aluminium alloy FinishFascia: Painted to RAL7035
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 20 of 86 4.1.7.3Parts List AFL Part #  Part Description  Qty.08-930002  2 PORT ISOLATOR 150-300MHz SMA  2 10-000701  1/4W0-30dB SWITCHED ATTENUATOR  2 10-000901  SW. ATTENUATOR 0.25W 0-15dB  2 11-006002  LNA VHF 70-500MHz WITH RELAY  4 12-002201  3 STAGE AMPLIFIER ALARM BOARD  2 12-002220  3 STAGE ALARM PCB COVER  2 12-002826  ALARM BOARD ACRYLIC LENS  2 12-004902  POWER AMP VHF 5W CLASS AB  1 12-005201  P/A 10W VHF CLASS AB  1 13-001803  DUAL DC/DC CONVERTER 24V-12V 1A  2 13-001822  DC-DC CON 24V-5V/15V COVER  2 17-009725  EQUIP. MTG PLATE No.6  2 17-010810  VHF CH MOD 15kHz 8p +IFRX 10k Gated  2 19-000922KL  3U chassis kit 450 deep with led  1 20-001601  12V RELAY BOARD  1 80-008902  24V RELAY PCB ASSEMBLY **NO LED**  1 80-063920  HEATSINK 2U ASS140 (5W)  2 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  4 91-500001  POWER PLG 3 PIN PNL.MOUNT NC-X  1 91-510003  3 PIN R.ANGLE FREE SOC.NC-X.  1 91-600001  'D'TYPE 9 WAY PLUG S/B TERM  1 91-600007  'D' 9 WAY BLACK SHELL  1 91-600014  'D' 9 WAY SOCKET S/B (NON FILTERED)  5 91-620001  'D' 25 WAY SOCKET S/B TERM  2 91-700017  ICD 15 WAY 0.1' CONNECTOR  3 93-000034  10dB IN LINE ATTENUATOR 1W SMA  1 96-110001  FUSE HOLDER 20 x 5mm6.3A  1 96-600002  INSULATING BOOT SMALL  1 96-600003  INSULATING BOOT D.C.  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 21 of 86 4.1.7.4System Diagram, Drg. # 50-146584
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 22 of 86 4.1.8 VHF Duplex BDA Channel 2 Shelf (50-146505) 4.1.8.P  VHF Duplex BDA Channel 2 Shelf Photographs The duplex shelves are all hardware similar – so only the channel 1 shelf photographs are shown (see section 4.1.7.P) 4.1.8.1DescriptionSee section 4.1.7.1 4.1.8.2Technical Specification See section 4.1.7.2 4.1.8.3Parts List AFL Part #  Part Description  Qty. 08-930002  2 PORT ISOLATOR 150-300MHz SMA  2 10-000701  1/4W0-30dB SWITCHED ATTENUATOR  2 10-000901  SW. ATTENUATOR 0.25W 0-15dB  4 11-006002  LNA VHF 70-500MHz WITH RELAY  4 12-002201  3 STAGE AMPLIFIER ALARM BOARD  2 12-002220  3 STAGE ALARM PCB COVER  2 12-002826  ALARM BOARD ACRYLIC LENS  2 12-004902  POWER AMP VHF 5W CLASS AB  1 12-005201  P/A 10W VHF CLASS AB  1 13-001803  DUAL DC/DC CONVERTER 24V-12V 1A  2 13-001822  DC-DC CON 24V-5V/15V COVER  2 17-009725  EQUIP. MTG PLATE No.6  2 17-010810  VHF CH MOD 15kHz 8p +IFRX 10k Gated  2 19-000922KL  3U chassis kit 450 deep with led  1 20-001601  12V RELAY BOARD  1 80-008902  24V RELAY PCB ASSEMBLY **NO LED**  1 80-063920  HEATSINK 2U ASS140 (5W)  2 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  4 91-500001  POWER PLG 3 PIN PNL.MOUNT NC-X  1 91-510003  3 PIN R.ANGLE FREE SOC.NC-X.  1 91-600001  'D'TYPE 9 WAY PLUG S/B TERM  1 91-600007  'D' 9 WAY BLACK SHELL  1 91-600014  'D' 9 WAY SOCKET S/B (NON FILTERED)  4 91-620001  'D' 25 WAY SOCKET S/B TERM  2 91-700017  ICD 15 WAY 0.1' CONNECTOR  3 93-000034  10dB IN LINE ATTENUATOR 1W SMA  1 96-110001  FUSE HOLDER 20 x 5mm6.3A  1 96-600002  INSULATING BOOT SMALL  1 96-600003  INSULATING BOOT D.C.  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 23 of 86 4.1.8.4System Diagram
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 24 of 86 4.1.9 VHF Simplex BDA Channel 3A Shelf (50-146506) 4.1.9.P  VHF Simplex BDA Photographs
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 25 of 86 4.1.9.1DescriptionThe simplex channel amplifier shelves (x3) receive their input signals from antennas and are processed as follows:- The Simplex controller module (17-015301) monitors the receiver output for a signal change and activates the supply switching for either the uplink or down link path accordingly. In normal operation, the low level Rx path is activated and the associated Tx path is switched off. When a signal is detected by the downlink channel selective module, the Rx output goes low, which triggers the controller logic PCB. The PCB mutes the power supply to the opposite path Rx LNA’s and switches on the power to the output power stage. In order to prevent the power stage noise blocking the opposite path’s low level receiver, the power amplifier is normally muted. Both outputs are protected by ferrite isolators in a similar way to the duplex shelves. All three simplex shelves are hardware similar so only channel 3A shelf is described. 4.1.9.2Technical Specification PARAMETER SPECIFICATIONHeight: 3U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg 154.785MHz (Ch. 3A)154.755MHz (Ch. 3B) Channel frequencies:154.980MHz (Ch. 4) Shelf gain: 100dB (typical) Impedance: 50ȍHumidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Case: Iridite NCP coating Heatsinks: Black anodised Handles: Silver anodised aluminium alloy FinishFascia: Painted to RAL7035
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 26 of 86 4.1.9.3System Diagram, Drg. # 50-146586
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 27 of 86 4.1.9.4Parts List AFL Part #  Part Description  Qty. 05-002901  3dB BROADBAND SPLITTER SMA 1WATT  4 08-930002  2 PORT ISOLATOR 150-300MHz SMA  2 10-000701  1/4W0-30dB SWITCHED ATTENUATOR  2 10-000723  2xSWITCHED ATTENUATOR FIXING PLATE  2 10-000901  SW. ATTENUATOR 0.25W 0-15dB  2 11-006002  LNA VHF 70-500MHz WITH RELAY  4 12-002201  3 STAGE AMPLIFIER ALARM BOARD  2 12-002220  3 STAGE ALARM PCB COVER  2 12-002826  ALARM BOARD ACRYLIC LENS  2 12-004902  POWER AMP VHF 5W CLASS AB  1 12-005201  P/A 10W VHF CLASS AB  1 13-001803  DUAL DC/DC CONVERTER 24V-12V 1A  2 13-001822  DC-DC CON 24V-5V/15V COVER  2 17-010810  VHF CH MOD 15kHz 8p +IFRX 10k Gated  2 17-015301  DUAL SIMPLEX CONTROLLER  1 19-000922KL  3U chassis kit 450 deep with led  1 20-001602  24V RELAY BOARD  2 80-008902  24V RELAY PCB ASSEMBLY **NO LED**  1 80-063920  HEATSINK 2U ASS140 (5W)  2 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  4 91-130005  SMA BULKHEAD ADAPTOR F/F  4 91-500001  POWER PLG 3 PIN PNL.MOUNT NC-X  1 91-510003  3 PIN R.ANGLE FREE SOC.NC-X.  1 91-600001  'D'TYPE 9 WAY PLUG S/B TERM  1 91-600014  'D' 9 WAY SOCKET S/B (NON FILTERED)  5 91-620001  'D' 25 WAY SOCKET S/B TERM  2 91-620005  'D' 25 WAY PLUG S/B TERM  1 91-700017  ICD 15 WAY 0.1' CONNECTOR  2 93-520015  10K PANEL/PCB MTG POT  2 93-540035  1K3 0.25W 1% RES MRS25 M:F  2 96-110001  FUSE HOLDER 20 x 5mm 6.3A  1 96-600002  INSULATING BOOT SMALL  1 96-600003  INSULATING BOOT D.C.  1 96-700017  LED AMBER 5mm SEALED IP66  2
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 28 of 86 4.1.10  VHF Simplex BDA Channel 3B Shelf (50-146507) 4.1.10.P  VHF Simplex BDA Channel 3B Photographs See section 4.1.9.P 4.1.10.1 Description See section 4.1.9.1 4.1.10.2 Technical Specification See section 4.1.9.2
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 29 of 86 4.1.10.3  System Diagram, Drg. # 50-146587
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 30 of 86 4.1.10.4 Parts List AFL Part #  Part Description  Qty. 05-002901  3dB BROADBAND SPLITTER SMA 1WATT  4 08-930002  2 PORT ISOLATOR 150-300MHz SMA  2 10-000701  1/4W0-30dB SWITCHED ATTENUATOR  2 10-000723  2 x SWITCHED ATTENUATOR FIXING PLATE  2 10-000901  SW. ATTENUATOR 0.25W 0-15dB  2 11-006002  LNA VHF 70-500MHz WITH RELAY  4 12-002201  3 STAGE AMPLIFIER ALARM BOARD  2 12-002220  3 STAGE ALARM PCB COVER  2 12-002826  ALARM BOARD ACRYLIC LENS  2 12-004902  POWER AMP VHF 5W CLASS AB  1 12-005201  P/A 10W VHF CLASS AB  1 13-001803  DUAL DC/DC CONVERTER 24V-12V 1A  2 17-010810  VHF CH MOD 15kHz 8p +IFRX 10k Gated  2 17-015301  DUAL SIMPLEX CONTROLLER  1 19-000922KL  3U chassis kit 450 deep with led  1 20-001602  24V RELAY BOARD  2 80-008902  24V RELAY PCB ASSEMBLY **NO LED**  1 80-063920  HEATSINK 2U ASS140 (5W)  2 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  4 91-130005  SMA BULKHEAD ADAPTOR F/F  4 91-500001  POWER PLG 3 PIN PNL.MOUNT NC-X  1 91-510003  3 PIN R.ANGLE FREE SOC.NC-X.  1 91-600001  'D'TYPE 9 WAY PLUG S/B TERM  1 91-600014  'D' 9 WAY SOCKET S/B (NON FILTERED)  5 91-620001  'D' 25 WAY SOCKET S/B TERM  2 91-620005  'D' 25 WAY PLUG S/B TERM  1 91-700017  ICD 15 WAY 0.1' CONNECTOR  2 93-520015  10K PANEL/PCB MTG POT  2 93-540035  1K3 0.25W 1% RES MRS25 M:F  2 96-110001  FUSE HOLDER 20 x 5mm6.3A  1 96-600002  INSULATING BOOT SMALL  1 96-600003  INSULATING BOOT D.C.  1 96-700017  LED AMBER 5mm SEALED IP66  2
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 31 of 86 4.1.11  VHF Simplex BDA Channel 4 Shelf (50-146508) 4.1.11.P  VHF Simplex BDA Channel 4 Shelf Photographs See section 4.1.9.P 4.1.11.1 Description See section 4.1.9.1 4.1.11.2 Technical Specification See section 4.1.9.2
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 32 of 86 4.1.11.3  System Diagram, Drg. # 50-146588
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 33 of 86 4.1.11.4 Parts List AFL Part #  Part Description  Qty. 08-930002  2 PORT ISOLATOR 150-300MHz SMA  2 10-000701  1/4W0-30dB SWITCHED ATTENUATOR  2 10-000723  2xSWITCHED ATTENUATOR FIXING PLATE  2 10-000901  SW. ATTENUATOR 0.25W 0-15DB  2 11-006002  LNA VHF 70-500MHz WITH RELAY  4 12-002201  3 STAGE AMPLIFIER ALARM BOARD  2 12-002220  3 STAGE ALARM PCB COVER  2 12-002826  ALARM BOARD ACRYLIC LENS  2 12-004902  POWER AMP VHF 5W CLASS AB  1 12-005201  P/A 10W VHF CLASS AB  1 13-001803  DUAL DC/DC CONVERTER 24V-12V 1A  2 13-001822  DC-DC CON 24V-5V/15V COVER  2 17-010810  VHF CH MOD 15kHz 8p +IFRX 10k Gated  2 17-015301  DUAL SIMPLEX CONTROLLER  1 19-000922KL  3U chassis kit 450 deep with led  1 20-001602  24V RELAY BOARD  2 80-008902  24V RELAY PCB ASSEMBLY **NO LED**  1 80-063920  HEATSINK 2U ASS140 (5W)  2 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  4 91-500001  POWER PLG 3 PIN PNL.MOUNT NC-X  1 91-510003  3 PIN R.ANGLE FREE SOC.NC-X.  1 91-600001  'D'TYPE 9 WAY PLUG S/B TERM  1 91-600014  'D' 9 WAY SOCKET S/B (NON FILTERED)  5 91-620001  'D' 25 WAY SOCKET S/B TERM  2 91-620005  'D' 25 WAY PLUG S/B TERM  1 91-700017  ICD 15 WAY 0.1' CONNECTOR  2 93-520015  10K PANEL/PCB MTG POT  2 93-540035  1K3 0.25W 1% RES MRS25 M:F  2 96-110001  FUSE HOLDER 20 x 5mm6.3A  1 96-600002  INSULATING BOOT SMALL  1 96-600003  INSULATING BOOT D.C.  1 96-700017  LED AMBER 5mm SEALED IP66  2
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 34 of 86 4.1.12  Downlink I/P Splitter (50-146509) 4.1.12.P  Downlink Input Splitter Photographs
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 35 of 86 4.1.12.1 Description The input splitter shelf receives VHF signals from the off-air antenna and passes them through two bandpass filters one of which is tuned to channel 2 and the other tuned to include channels 1, 3A, 3B &4. The output of the filter tuned for channel 2 goes directly to the channel 2 cell enhancer input but the other path is split by four crystal filters, the outputs of which go separately to the inputs of the respective cell enhancer inputs. This is a passive shelf with no connection to any DC source and no alarms.4.1.12.2 Technical Specification PARAMETER SPECIFICATIONHeight: 3U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg Frequency ranges passed: 153.965 to 154.980 & 158.925MHz Impedance: 50ȍHumidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Case: Iridite NCP coat Heatsinks: None Handles: Silver anodised aluminium alloy FinishFascia Painted to RAL7035 4.1.12.3 Parts List AFL Part #  Part Description  Qty.01-003105  SD NOTCH FILT.N 6 SECT.VHF H/B SMA  2 19-000922K  3U CHASSIS KIT (450mm deep)  1 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  6 91-130001  SMA ADAPT 'T' ALL FEMALE 3 GHz  4 93-980194  153.965MHz CRYSTAL FILT FAN4M52500  1 93-980195  154.755MHz CRYSTAL FILT FAN4M52500  1 93-980196  154.785MHz CRYSTAL FILT FAN4M52500  1 93-980197  154.980MHz CRYSTAL FILT FAN4M52500  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 36 of 86 4.1.12.4  System Diagram, Drg. # 50-146589
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 37 of 86 4.1.13  Downlink O/P Combiner (50-146510) 4.1.13.P  Downlink O/P Combiner Photographs
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 38 of 86 4.1.13.1 Description The passive downlink output combiner shelf receives the five separate VHF cell enhancer output signals and couples them together through hybrid and bandpass filters into three identical paths. This shelf has no power source and no alarms. 4.1.13.2 Technical Specification PARAMETER SPECIFICATIONHeight: 3U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg Frequency ranges passed: 153.965 to 154.980 & 158.925MHz Impedance: 50ȍHumidity: 5 – 95% non-condensing RF Connectors: N type female Environmental protection: IP44 Case: Iridite NCP coat Heatsinks: None Handles: Silver anodised aluminium alloy FinishFascia Painted to RAL7035 4.1.13.3 Parts List AFL Part #  Part Description  Qty.01-003105  SD NOTCH FILT.N 6 SECT.VHF H/B SMA  2 05-000103  TX HYBRID COUPLER 3 PORT NO HTSINK  3 19-000922K  3U CHASSIS KIT (450mm deep)  1 91-030002  N ADAPTOR PANEL FEMALE:FEMALE  6 91-130001  SMA ADAPT 'T' ALL FEMALE 3 GHz  1
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 39 of 86 4.1.13.4 System Diagram
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 40 of 86 4.1.14  VHF/UHF 24V Power Supply Shelf (50-146512) 4.1.14.P  VHF/UHF Power supply Shelf Photographs
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 41 of 86 4.1.14.1  VHF/UHF PSU Shelf Description The power supply shelf consists of two, 400Watt 24V DC O.E.M modules which are commonly supplied from the mains but separately switched. The DC outputs are separately monitored and this data becomes half of the alarm data for the shelf (the two monitor loops are summed to form a single alarm relay contact pair). A pair of low-loss power diodes combine the outputs from the PSU modules in a redundant configuration such that if either module fails, the other supply would still be active but the faulty supply’s DC LED on the front panel would be extinguished and the alarm loop would be broken.4.1.14.2  VHF/UHF PSU Shelf Technical Specification PARAMETER SPECIFICATIONHeight: 5U Width: 19" (482.6mm) Shelfdimensions: Depth: <450mm (excluding connectors & handles) operational: -20°C to +60°C Temperaturerange: storage: -40°C to +70°C Weight: <10kg Humidity: 5 – 95% non-condensing DC Output connectors:  6 x XLR female DC Output Voltage: 24V DC (x 6) 24V DC O/P fuse rating: 10A (x 6) Environmental protection: IP44 Alarms: PSU1 & 2 (‘D’ connector pins 1 & 2) Case: Iridite NCP coat Heatsinks: Black anodised aluminium Handles: Silver anodised aluminium alloy FinishFascia Painted to RAL7035
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 42 of 86 4.1.14.3  VHF/UHF PSU Shelf Parts List AFL Part #  Part Description  Qty.13-003301  MAINS FILTER 8AMP ASSEMBLY  1 16-000222  DUPLEXER/CELL ENHANCER CASE RAIL  4 20-001601  12V RELAY BOARD  1 80-008920  DUAL PSU HEATSINK  2 80-008921  DUAL PSU CASE  1 80-008922  DUAL PSU LID  1 80-008925  DUAL PSU FRONT PANEL  1 91-500025  3 PIN RIGHT ANGLE FREE PLUG NC-X  6 91-510004  3 PIN PNL.MOUNT SOCKET NC-X  6 91-510035  3 WAY MATE N LOK PLUG HOUSING  2 91-520001  PWR MAINS INL FIXED/SOLD.TERMS  1 91-520005 MAINS LEAD  1 91-520010  MAINS RETAINING CLIP  1 91-520032  MATE N LOK SOCKET CONTACT 20/14 AWG  6 91-600015  'D' 9 WAY PLUG S/B (NON FILTERED)  1 91-800014  3 WAY TERMINAL BLOCK  1 91-800015  TRIPLE DECK TERMINAL BLOCK  8 91-800016  TRIPLE DECK TERMINAL JUMPER  6 91-800017  TRIPLE DECK TERMINAL END  1 91-800028  DIN RAIL END-STOP  2 91-800031  SYMETRIC 35 x 7.5mm DIN RAIL  0 92-900014  DIN RAIL (TOP HAT) EARTH CLAMP M5  1 93-510077  0R02 50W RESISTOR ALUMINIUM CLAD  2 94-100004  STPS12045TV 60A DUAL DIODE  1 95-100007  TX.FERRITE ISOL.HT.SINK B/ANOD  3 96-110034  FUSE HOLDER 16-30A, 32mm BODY ONLY  6 96-110064  FUSE HOLDER 16-30A, 32mm INSERT  6 96-300054  24V 17A PSU 400W (XP BCC)  2 96-600001  INSULATING BOOT LARGE  1 96-700034  LED RED 5mm IP67 INTEGRAL RES. 24V  1 96-700035  LED GREEN 5mm IP67 INTEGRAL RES 24V  2 96-920023  5A CIRCUIT BREAKER (ETA)  2 97-400002  HANDLE TYPE H6803 4U.[ALLOY]  2
Bronx Justice Centre Radio Repeaters Handbook Number: 80-283501HBKM  Page: 43 of 86 4.1.14.4  VHF/UHF PSU Shelf System Diagram, (needs new drawing)

Navigation menu