PEGATRON CLG8202SEC-NA Wireless Home Automation and Security User Manual Safety
PEGATRON CORPORATION Wireless Home Automation and Security Users Manual Safety
PEGATRON >
Contents
- 1. Users Manual Safety
- 2. Users Manual rev
Users Manual Safety
Print Vendor Remove Before Printing Printing Specifications Digital Life Controller – International (DLCi) Safety Sheet - English 78-100374-01A0 INLET Page Size: Color process: Paper weight: Paper type: Varnish: Number of Pages: 180mm x 160mm (7.06 x 6.31 inches) Black (1/1) double sided 60# Opaque N/A 12 COVER N/A BINDING Saddle stitch IMPORTANT SAFETY INSTRUCTIONS Notice to Installers The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. This symbol is intended to alert you of the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product. CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. WARNING TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. T16484 This symbol is intended to alert you that uninsulated voltage within this product may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this product. Notice à l’attention des installateurs de réseaux câblés Les instructions relatives aux interventions d’entretien, fournies dans la présente notice, s’adressent exclusivement au personnel technique qualifié. Pour réduire les risques de chocs électriques, n’effectuer aucune intervention autre que celles décrites dans le mode d’emploi et les instructions relatives au fonctionnement, à moins que vous ne soyez qualifié pour ce faire. Ce symbole a pour but de vous prévenir de la présence d’instructions importantes relatives au fonctionnement ou à l’entretien (et aux réparations) dans la documen- tation accompagnant ce produit. ATTENTION DANGER ÉLECTRIQUE NE PAS OUVRIR ATTENTION : Pour réduire les risques de chocs électriques, ne pas enlever le couvercle (ou le panneau arrière). Ne contient aucune pièce réparable par l’utilisateur. Confier les interventions aux techniciens d’entretien qualifiés. AVERTISSEMENT POUR ÉVITER LES INCENDIES OU LES CHOCS ÉLECTRIQUES, NE PAS EXPOSER L’APPAREIL À LA PLUIE OU À L’HUMIDITÉ. T16485 Ce symbole a pour but de vous prévenir que des tensions électriques non isolées existent à l'intérieur de ce produit, pouvant être d'une intensité suffisante pour causer des chocs électriques. Il est donc dangereux d'établir un contact quelconque avec l’une des pièces comprises à l’intérieur de ce produit. Mitteilung für CATV-Techniker Die in dieser Mitteilung aufgeführten Wartungsanweisungen sind ausschließlich für qualifiziertes Fachpersonal bestimmt. Um die Gefahr eines elektrischen Schlags zu reduzieren, sollten Sie keine Wartungsarbeiten durchführen, die nicht ausdrücklich in der Bedienungsanleitung aufgeführt sind, außer Sie sind zur Durchführung solcher Arbeiten qualifiziert. Dieses Symbol weist den Benutzer darauf hin, dass die mit diesem Produkt gelieferte Dokumentation wichtige Betriebs- und Wartungsanweisungen für das Gerät enthält. ACHTUNG STROMSCHLAGGEFAHR, NICHT ÖFFNEN ACHTUNG: Zur Vermeidung eines Stromschlags darf die Abdeckung (bzw. die Geräterückwand) nicht entfernt werden. Das Gerät enthält keine vom Benutzer wartbaren Teile. Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal durchgeführt werden. WARNUNG DAS GERÄT NICHT REGEN ODER FEUCHTIGKEIT AUSSETZEN, UM STROMSCHLAG ODER DURCH EINEN KURZSCHLUSS VERURSACHTEN BRAND ZU VERMEIDEN. T16486 Dieses Symbol weist den Benutzer auf das Vorhandensein von nicht isolierten gefährlichen Spannungen im Gerät hin, die Stromschläge verursachen können. Ein Kontakt mit den internen Teilen dieses Produktes ist mit Gefahren verbunden. Aviso a los instaladores de sistemas CATV Las instrucciones de reparación contenidas en el presente aviso son para uso exclusivo por parte de personal de mantenimiento cualificado. Con el fin de reducir el riesgo de descarga eléctrica, no realice ninguna otra operación de reparación distinta a las contenidas en las instrucciones de funcionamiento, a menos que posea la cualificación necesaria para hacerlo. Este símbolo tiene como fin alertarle de la presencia de importantes instrucciones de operación y mantenimiento (revisión) contenidas en la literatura que acompaña al producto. ATENCIÓN RIESGO DE DESCARGA ELÉCTRICA NO ABRIR ATENCIÓN: con el fin de reducir el riesgo de descarga eléctrica, no retire la tapa (ni la parte posterior). No existen en el interior componentes que puedan ser reparados por el usuario. Encargue su revisión a personal de mantenimiento cualificado. ADVERTENCIA PARA EVITAR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, NO EXPONGA LA UNIDAD A LA LLUVIA O LA HUMEDAD. T16261 Este símbolo tiene como fin advertirle de que una tensión sin aislamiento en el interior de este producto podría ser de una magnitud suficiente como para provocar una descarga eléctrica. Por consiguiente, resulta peligroso realizar cualquier tipo de contacto con alguno de los componentes internos de este producto. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip over. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Power Source Warning A label on this product indicates the correct power source for this product. Operate this product only from an electrical outlet with the voltage and frequency indicated on the product label. If you are uncertain of the type of power supply to your home or business, consult your service provider or your local power company. The AC inlet on the unit must remain accessible and operable at all times. Protect the Product from Lightning In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs. Verify the Power Source from the On/Of Power Light When the on/of power light is not illuminated, the apparatus may still be connected to the power source. The light may go out when the apparatus is turned of, regardless of whether it is still plugged into an AC power source. Eliminate AC Power/Mains Overloads WARNING: Avoid electric shock and fire hazard! Do not overload AC power/ mains, outlets, extension cords, or integral convenience receptacles. For products that require battery power or other power sources to operate them, refer to the operating instructions for those products. Handling Disposable Batteries This product may contain a rechargeable LithiumIon battery to provide stand-by operation in the event of an AC power failure. Heed the following warning, follow the Battery Safety and Battery Disposal instructions below, and see the instructions later in this guide for handling, replacing, and disposing of the battery. WARNING: There is danger of explosion if the battery is mishandled or incorrectly replaced. Replace only with the same type of battery. Do not disassemble it or attempt to recharge it outside the system. Do not crush, puncture, dispose of in fire, short the external contacts, or expose to water or other liquids. Dispose of the battery in accordance with local regulations and instructions from your service provider. Battery Safety • Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted. • Do not attempt to recharge ‘disposable’ or ‘nonreusable’ batteries. • Please follow instructions provided for charging ‘rechargeable’ batteries. • Replace batteries with the same or equivalent type that we recommend. • Do not expose batteries to excessive heat (such as sunlight or ire). • Do not expose batteries to temperatures above 100°C (212°F). Battery Disposal • The batteries may contain substances that could be harmful to the environment. • Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/national disposal and recycling regulations. Protect from Exposure to Moisture and Foreign Objects • The batteries may contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchloratecontaining substance, see www.dtsc.ca.gov/ hazardouswaste/perchlorate WARNING: Avoid electric shock and fire hazard! Do not expose this product to dripping or splashing liquids, rain, or moisture. Objects filled with liquids, such as vases, should not be placed on this apparatus. Provide Ventilation and Select a Location WARNING: Avoid electric shock and fire hazard! Unplug this product before cleaning. Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device (dust remover) to clean this product. • Remove all packaging material before applying power to the product. • Do not place this apparatus on a bed, sofa, rug, or similar surface. • Do not place this apparatus on an unstable surface. • Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper ventilation. • Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or other objects on top of this product. • Do not block ventilation openings. Operating Environment This product is designed for operation indoors with a temperature range from 32° to 104° F (0° to 40°C). Each product should have adequate spacing on all sides so that the cooling air vents on the chassis are not blocked. WARNING: Avoid electric shock and fire hazard! Never push objects through the openings in this product. Foreign objects can cause electrical shorts that can result in electric shock or fire. Service Warnings WARNING: Avoid electric shock! Do not open the cover of this product. Opening or removing the cover may expose you to dangerous voltages. If you open the cover, your warranty will be void. This product contains no user-serviceable parts. Check Product Safety Upon completion of any service or repairs to this product, the service technician must perform safety checks to determine that this product is in proper operating condition. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected. Protect the Product When Moving It Consult the service provider or an experienced radio/television technician for help. Always disconnect the power source when moving the apparatus or connecting or disconnecting cables. SAVE THESE INSTRUCTIONS Any changes or modiications not expressly approved by Cisco Systems, Inc., could void the user’s authority to operate the equipment. United States FCC Compliance This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is intended to supply you with information regarding the FCC approval of this device. The phone numbers listed are for FCC-related questions only and not intended for questions regarding the connection or operation for this device. Please contact your service provider for any questions you may have regarding the operation or installation of this device. Declaration of Conformity This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device may not cause harmful interference, and 2) the device must accept any interference received, including interference that may cause undesired operation. Manufactured by: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA www.cisco.com/go/contacts Canada EMI Regulation This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada. RF Exposure Statements Note: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body. US FCC Exposure Statement: ThisRadiation system has been evaluated for RF This equipment complies with FCC radiation exposure limits set forth exposure for humans in reference to ANSI C for an uncontrolled environment. This equipment should be installed 95.1 (American National and operated with minimum distanceStandards 20cm between Institute) the radiator & limits. your bodyThe evaluation was based in accordance with FCC OET Bulletin 65C rev 01.01 in For product available in the USA/Canada market, only channel 1~11 compliance with Part 2.1091 and Part 15.27. can be operated. Selection of other channels is not possible. The minimum separation distance from the This device and antennas(s) must not beis co-located or operating antenna to it's general bystander 7.9 inches (20 in conjunction with any other antenna or transmitter except in cm) to maintain compliance. accordance with FCC multi-transmitter product procedures. Canada This system has been evaluated for RF exposure for humans in reference to Canada Health Code 6 (2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The minimum separation distance from the antenna to general bystander is 7.9 inches (20 cm) to maintain compliance. EU This system has been evaluated for RF exposure for humans in reference to the ICNIRP (International Commission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN 62311 Product Standard to Demonstrate Compliance of Radio Base Stations and Fixed Terminals for Wireless Telecommunications Systems with basic restrictions or reference levels related to Human Exposure to Radio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. The minimum separation distance from the antenna to general bystander is 20 cm (7.9 inches). Australia This system has been evaluated for RF exposure for humans as referenced in the Australian Radiation Protection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing Radiation Protection) limits. The minimum separation distance from the antenna to general bystander is 20 cm (7.9 inches). CE Compliance Declaration of Conformity with Regard to the EU Directive 1999/5/ EC (R&TTE Directive) Български [Bulgarian] Česky [Czech]: Dansk [Danish]: This declaration is only valid for conigurations (combinations of software, irmware and hardware) supported or provided by Cisco Systems for use within the EU. The use of software or irmware not supported or provided by Cisco Systems may result in the equipment no longer being compliant with the regulatory requirements. Това оборудване отговаря на съществените изисквания и приложими клаузи на Директива 1999/5/ЕС. Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC. Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF. Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU. Eesti [Estonian]: See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele. English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish]: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE. Ελληνική [Greek]: Αυτός ο εξοπλισμός είναι σε συμμόρφωση με τις ουσιώδεις απαιτήσεις και άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC. Français [French]: Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC. Íslenska [Icelandic]: Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC. Italiano [Italian]: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE. Latviski [Latvian]: Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian]: Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas. Nederlands [Dutch]: Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC. Malti Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra [Maltese]: rilevanti tad-Direttiva 1999/5/EC. Magyar [Hungarian]: Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket. Norsk [Norwegian]: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF. Polski Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi [Polish]: warunkami określonymi Dyrektywą UE: 1999/5/EC. Português Este equipamento está em conformidade com os requisitos essenciais e [Portuguese]: outras provisões relevantes da Directiva 1999/5/EC. Română [Romanian] Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC. Slovensko Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi [Slovenian]: pogoji Direktive 1999/5/EC. Slovensky [Slovak]: Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC. Suomi [Finnish]: Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen. Svenska [Swedish]: Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC. Note: The full declaration of conformity for this product can be found at http://www.cisco.com/ web/consumer/support/compliance_info.html. The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC: The CE mark and class-2 identiier are aixed to the product and its packaging. This product conforms to the following European directives: -1999/5/EC National Restrictions This product is for indoor use only. France For 2.4 GHz, the output power is restricted to 10 mW EIRP when the product is used outdoors in the band 2454 - 2483.5 MHz. There are no restrictions when used in other parts of the 2.4 GHz band. Check http://www.arcep.fr/ for more details. Pour la bande 2,4 GHz, la puissance est limitée à 10 mW en p.i.r.e. pour les équipements utilisés en extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations dans d’autres parties de la bande 2,4 GHz. Consultez http://www.arcep.fr/ pour de plus amples détails Italy This product meets the National Radio Interface and the requirements speciied in the National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner’s property, its use requires a “general authorization.” Please check http://www.comunicazioni.it/it/ for more details. Questo prodotto è conforme alla speciiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all ‘interno del proprio fondo, l’utilizzo di prodotti Wireless LAN richiede una “Autorizzazione Generale”. Consultare http:// www.comunicazioni.it/it/ per maggiori dettagli. Latvia The outdoor usage of the 2.4 GHz band requires an authorization from the Electronic Communications Oice. Please check http:// www.esd.lv for more details. 2,4 GHz frekvenču joslas izmantošanai ārpus telpām nepieciešama atļauja no Elektronisko sakaru direkcijas. Vairāk informācijas: http://www.esd.lv. Note: The regulatory limits for maximum output power are speciied in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used (speciied in dBi) to the output power available at the connector (speciied in dBm). Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its ailiates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) © 2014 Cisco and/or its ailiates. All rights reserved Printed in China Last Updated: June 2014 78-100374-01A0 78-100374-01A0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2014:05:20 08:20:26-04:00 Keywords : 78-100374-01A0, Digital Life Controller, DLCi Modify Date : 2014:07:01 15:38:51+08:00 Has XFA : No Language : EN-US Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Metadata Date : 2014:07:01 15:38:51+08:00 Creator Tool : Acrobat PDFMaker 10.1 for Word Document ID : uuid:d4a61835-a6c2-4aa8-ba5b-65d55c292dd2 Instance ID : uuid:5aae2742-3612-42da-8fa9-a99e7151c645 Format : application/pdf Creator : Title : Digital Life Controller – International (DLCi) Safety Sheet - English Description : This document provides set-top regulatory compliance/safety information for Digital Life Controller products. Written for the home subscriber. Copyright May 2014. Subject : 78-100374-01A0, Digital Life Controller, DLCi Producer : Adobe PDF Library 10.0 Source Modified : D:20140520122021 Company : Cisco Systems State : 1 Version : 1.1 Page Layout : OneColumn Page Count : 13EXIF Metadata provided by EXIF.tools