PEGATRON VJZ12AD11L 2x2 PCIe M.2 adapter card User Manual

PEGATRON CORPORATION 2x2 PCIe M.2 adapter card

Contents

User manual

Intel® Dual Band Wireless-AC 7265 User manual All rights reserved. Intel Corporation, Introduction: Intel®DualBandWireless‐AC7265(codenameStonePeak2orStP2)shallbetheVHT‐5GWi‐Fi2x2andBluetoothcombinationsinglechipsolution.StP2shalluseIntel’s2ndgeneration802.11acWi‐Fisolutionandshallsupportboth2.4and5.2GHzbands.Onthe5.2GHzbanditshalloperateonan80MHzwidechannelreachingPHYratesofupto867Mbps.StP2shalluseaBluetoothcorethatshallsupportBluetooth4.0standardincludingBluetooth4.0LowEnergy(BLE).StP2shallhave2antennaports:oneshallbeWi‐FionlyandthesecondwillbesharedbetweenWi‐FiandBluetooth.Wi‐FishallsupportRxantennadiversity. HWdescribe: Form Factors M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 Antenna Interface Connector Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity IEEE 802.11 Networking Standards 802.11abgn, 802.11ac, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w Operating Temperature 0 to +80 degrees Celsius Humidity 50% to 90% RH non-condensing (at temperatures of 25 ºC to 35 ºC) Frequency Modulation 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) Frequency band 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) ChannelsAll channels as defined by the relevant specification and country rules.
Spatial streamsIntel® Dual Band Wireless-AC 7265: 2 X 2Data RatesAll data rates are theoretical maximums.IEEE 802.11ac Data RatesIntel® Dual Band Wireless-AC 7265: Up to 867 MbpsIEEE 802.11n Data RatesTx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2IEEE 802.11a Data Rates54, 48, 36, 24, 18, 12, 9, 6 Mbps IEEE 802.11g Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps IEEE 802.11b Data Rates11, 5.5, 2, 1 MbpsBluetoothDual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE)GeneralOperating Systems Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (64-bit) Wi-Fi Alliance* certification Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions certification Cisco Compatible Extensions, v4.0 Security Authentication WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA Authentication Protocols PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 
Encryption 64-bit and 128-bit WEP, AES-CCMP, TKIP Wi-Fi Direct* Encryption and Authentication WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) InstallWLANcardtothehostplatformbyfactory.SWdescribe: Portions of Intel® PROSet/Wireless WiFi Connection Utility include software under the following terms:1. Setupthe Intel® PROSet for installing driver to the host platform. 2. Use the administrator to installing driver.Portions Licensed from Devicescape Software, Inc. Intel® PROSet/Wireless WiFi Connection Utility contains software licensed from Devicescape Software, Inc. Copyright (c) 2004 - 2008 Devicescape Software, Inc. All rights reserved.
Antenna Placement Within the Host Platform To ensure RF exposure compliance the antenna(s) used with the Intel® wireless adapters must be installed in notebook or tablet PC host platforms to provide a minimum separation distance from all persons, in all operating modes and orientations of the host platform, with strict adherence to the table below. The antenna separation distance applies to both horizontal and vertical orientation of the antenna when installed in the host system. Wireless AdapterMinimum required antenna-to-user separation distanceIntel® Dual Band Wireless-AC 72658 mm* This wireless adapter may be installed in mobile devices only (requires > 20 cm antenna separation from the body of user). Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Intel® wireless adapter, in compliance with local regulations. Host system must be labeled with "Contains FCC ID: VUIVJZ12AD11L", FCC ID displayed on label.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Federal Communication Commission (FCC) Radiation Exposure Statement This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification , Doc) of the host device to be addressed by the integrator/manufacturer. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: VUIVJZ12AD11L ". 

Navigation menu