Panasonic Devices Europe EM250B ETRX2-PA, STRX2-PA, ETRX2HR-PA, STRX2HR-PA User Manual 1
Panasonic Industrial Devices Europe GmbH ETRX2-PA, STRX2-PA, ETRX2HR-PA, STRX2HR-PA 1
Manual
CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 1 of 33 DATE 25.10.2007 Datum Specification for Production Applicant / Manufacturer Hardware Panasonic Electronic Devices (Europe) GmbH Zeppelinstrasse 19 21337 Lüneburg Germany Applicant / Manufacturer Software Ember Inc. Telegesis (UK) Limited Contents Approval for Mass Production Customer Telegesis (UK) Limited By signing this document, Customer accepts the validity of the below-mentioned contents and declares his full notice to it. Some passages may be changed if required; the validity shall not be affected thereby. CHECKED / APPROVED: DATE: NAME: SIGNATURE: NOTE: AT LEAST ONE SET OF APPROVED SPECIFICATIONS SHOULD BE RETURNED TO THE ADDRESS OF THE ISSUING PARTY. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 2 of 33 DATE 25.10.2007 Datum TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. Key Features ...................................................................................................................4 Applications for the Module .............................................................................................4 Description of the Module................................................................................................5 3.1. On board DC Regulator .........................................................................................5 3.2. On Board reference Crystal ...................................................................................5 Scope of this Document ..................................................................................................6 History for this Document ................................................................................................6 Terminal Layout...............................................................................................................7 Block Diagram ...............................................................................................................10 Key Parts List ................................................................................................................10 Test Conditions .............................................................................................................10 Absolute Maximum Ratings...........................................................................................11 Operating Conditions.....................................................................................................11 DC Electrical Characteristics.........................................................................................12 A/D converter Characteristics........................................................................................13 AC Electrical Characteristics .........................................................................................14 14.1. Tx power characteristics ......................................................................................16 Mechanical Requirements.............................................................................................17 Soldering Temperature-time profile (for reflow soldering) .............................................18 16.1. For lead solder .....................................................................................................18 16.2. For lead free solder ..............................................................................................18 Module Dimensions.......................................................................................................19 Foot Print of the Module ................................................................................................19 Labeling Drawing...........................................................................................................20 Recommended Land Pattern ........................................................................................20 Software ........................................................................................................................21 21.1. Software Declaration............................................................................................21 21.2. Software Tools .....................................................................................................21 21.3. Ember ZigBee® Stack .........................................................................................22 Reliability Tests .............................................................................................................22 Application Notes ..........................................................................................................22 23.1. Cautions for safety ...............................................................................................22 23.2. Design engineering notes ....................................................................................23 23.3. Storage conditions ...............................................................................................24 Packaging......................................................................................................................25 24.1. Embossed tape / Blistergurt .................................................................................25 24.2. Component direction ............................................................................................26 HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF 25. 26. 27. 28. 29. 30. 31. No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 3 of 33 DATE 25.10.2007 Datum 24.3. Reel dimension ....................................................................................................26 24.4. Package ...............................................................................................................27 Ordering Information .....................................................................................................28 RoHS Declaration..........................................................................................................29 Data Sheet Status .........................................................................................................29 Regulatory Information ..................................................................................................30 28.1. FCC Notice ..........................................................................................................30 28.2. Caution.................................................................................................................30 28.3. Labeling Requirements ........................................................................................30 28.4. Antenna Installation Instructions ..........................................................................31 28.5. Approved Antenna List.........................................................................................31 28.6. RF Exposure ETRX2-PA......................................................................................32 Related Documents.......................................................................................................33 General Information.......................................................................................................34 Life Support Policy ........................................................................................................34 HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF 1. No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 4 of 33 DATE 25.10.2007 Datum KEY FEATURES Schlüsseleigenschaften • short range 2,4GHz ISM band IEEE802.15.4 [1] compliant transceiver • Complete system based on the ZigBee ® compliant platform EM250 that combines the transceiver with a powerful, efficient industry proven 16-bit microprocessor with comprehensive hardware supported network-level debugging features • designed specifically for use with EmberZNet, Embers ZigBee® compliant embedded mesh networking • powerful 16-bit microprocessor • 128k flash ROM and 5k of SRAM memory • high Rx sensitivity of –97dBm at 1% Packet Error Rate • increased Tx output power setting range from -20dBm to +17dBm • Small size 20,5mm x 37,5mm x 2.8mm • single port antenna terminal (pcb pad, U.FL socket or chip antenna versions available) • Integrated ADC module with 12-bit resolution • two 16-bit general purpose timers; one 16-bit sleep timer • 17 GPIO pins with alternate functions • two sleep modes for increased battery life • low voltage detect/reset • complies with ETSI EN300328 and FCC part15 2. APPLICATIONS FOR THE MODULE Anwendungen für das Modul • • • • • • • • ZigBee® Coordinators,Routers and End Devices working in star and mesh networks Wireless sensor and actuator networks Remote control and wire replacement in industrial systems Building automation and control Inventory and logistics management HID (Human Interface Devices) Toys Home gateways HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF 3. No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 5 of 33 DATE 25.10.2007 Datum DESCRIPTION OF THE MODULE Beschreibung des Moduls ETRX2-PA contains the single chip EM250 [2] from Ember Inc., a 24MHz reference crystal and RF frontend circuitry optimized for best RF performance. As single ended RF output the module is available with integrated antenna or 50ohms or U.FL male socket [3] or 50 ohms pad terminal on the bottom of the module. Compared to ETRX2 the ETRX2-PA module allows extended range of operation by means of an integrated high efficieny power amplifier inserted in the Tx path. A low loss LTCC bandpassfilter for the 2,4GHz I.S.M. band has an effect on both Tx and Rx path. As a result for Rx mode the immunity against interferers (for example operating at 1,8 GHz) is improved compared to ETRX2. Two additional hardware options are available on request: 3.1. ON BOARD DC REGULATOR Although the EM250 already contains a dc regulator internally, the module can be requested with an extra integrated onboard dc regulator. Some applications could benefit from this additional regulator because as of for example: (1) Further extension of the input voltage range or (2) Extented battery life by replacing the regulator within EM250 by a special ultra low quiescent current regulator or (3) allowing for operation on very noisy power supplies Two different types of regulators can be chosen, a linear low dropout (LDO) type or a high efficiency switched buck regulator. Depending on the power supply conditions of the application the optimum regulator can be selected on demand. 3.2. ON BOARD REFERENCE CRYSTAL A second option that is available is an on board 32,768kHz crystal reference. This option is provided for applications that require a precision reference clock. Please contact the manufacturer if one of the options could be useful for your product design. ETRX2-PA is used for ZigBee® (www.zigbee.org) applications working with EmberZNetTM of Ember Inc. (www.ember.com). EmberZNetTM is a fully ZigBee® compliant networking stack. For code development Insight DesktopTM, a comprehensive integrated development environment (IDE) and C-language compiler toolchain from Ember Inc. is required. Insight DesktopTM is part of Ember development kits and can currently be purchased together with programming adaptors as EM250 jumpstart kit at a price of USD 2500,- directly from Ember Inc. (www.ember.com). HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 6 of 33 DATE 25.10.2007 Datum When using ZigBee® technology for a product the following additional costs have to be taken into account: (1) Membership of the ZigBee® Alliance, as least as adopter member for US$ 3.500,-. (2) The cost of a ZigBee® product certification at a testhouse (TÜV Rheinland) ranges from approximately US$ 2.500,- to US$ 10.000,-, depending on the implemented software. (3) Products qualifying for ZigBee® certification at the ZigBee® Alliance need a logo administration fee of US$ 1000,- for the first product, and US$ 500,- for each additional product. For more details on ZigBee® software see also part 21. 4. SCOPE OF THIS DOCUMENT Umfang dieses Dokumentes This product specification applies to the ZigBee ready modem ENWC9A13A3EF / ENWC9A16A3EF. The last character indicates different versions (refer to part 28 Ordering Information). The used chip is the EM250 from the US company Ember Inc. www.ember.com. Diese Produktionsunterlagen beziehen sich auf das ZigBee ready Modem ENWC9A13A3EF / ENWC9A16A3EF. Das letzte Zeichen bezeichnet verschiedene Versionen (Erklärung im Kapitel 25 Ordering Information). Der verwendete ZigBee Chip ist EM250 der US Firma Ember Inc. 5. HISTORY FOR THIS DOCUMENT Versionsverwaltung dieses Dokumentes Revision Version Date Datum Modification / Remarks Änderungen / Bemerkungen 06.06.2007 Preliminary 13.06.2007 Corrections based on review of Telegesis 05.10.2007 Updated parts 11 to 14 because of changed pcw and partslist (EMC issue) 25.10.2007 Due to FCC qualification update in chapter 28.1, 28.3, 28.4, 28.6. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF 6. No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 7 of 33 DATE 25.10.2007 Datum TERMINAL LAYOUT Anschlußbelegung The table below informs about the 38 module pin signals for direct SMD soldering of ETRX2-PA to the application board. The signal names are identical to the signal names of EM250, except for RF and VC1. The pin numbers in brackets () are the related pins of the pin/header connector X5, which is only mounted for special plug versions. Pin No. Pin Name Signal Name Pin Type Description 1(3) GND1 GND I/O ground RF RF I/O RF input/output terminal GND3 GND I/O ground 4(1) GPIO0 GPIO0 MOSI MOSI TMR1IA.1 I/O Digital I/O SPI master data out of serial controller SC2 SPI slave data in of serial controller SC2 Capture Input A of Timer 1 5(2) REG_OUT REG_OUT output of EM250 regulator voltage VREG_OUT (1) GND2 GND I/O ground 7(10) VBAT VBAT module dc supply voltage GND3 GND I/O ground 9(4) GPIO4 GPIO4 ADC0 PTI_EN I/O Analog Digital I/O ADC Input 0 Frame signal of Packet Trace Interface (PTI) HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF Pin No. Pin Name Signal Name GPIO5 ADC1 PTI_DATA GPIO3 SSEL TMR1IB.1 GPIO2 MSCLK MSCLK SCL TMR2IB.2 GPIO1 MISO MISO SDA TMR2IA.2 GPIO12 RTS TMR2IB.1 Pin Type I/O Analog I/O I/O I/O I/O I/O I/O 10(5) GPIO5 11(6) GPIO3 12(7) GPIO2 13(8) GPIO1 14(9) GPIO12 15 GND4 GND I/O 16 SIF_CLK SIF_CLK 17 SIF_MISO SIF_MISO No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 8 of 33 DATE 25.10.2007 Datum Description Digital I/O ADC Input 1 Data signal of Packet Trace Interface (PTI) Digital I/O SPI slave select of Serial Controller SC2 Capture Input B of Timer 1 Digital I/O SPI master clock of Serial Controller SC2 SPI slave clock of Serial Controller SC2 I2C clock of Serial Controller SC2 Capture Input B of Timer 2 Digital I/O SPI master data in of Serial Controller SC2 SPI slave data out of Serial Controller SC2 I2C data of Serial Controller SC2 Capture Input A of Timer 2 Digital I/O UART RTS handshake of Serial Controller SC1 Capture Input B for Timer 2 ground Serial interface, clock (internal pull-down) Serial interface, master in / slave out Serial interface, master out / slave in. In order to guarantee the deep sleep current limits as specified this pin has to be pulled to GND externally, typically with a 10 kiloohms resistor. Serial interface, load strobe (open-collector with internal pull-up) ground 18 SIF_MOSI SIF_MOSI 19 SIF_LOADB SIF_LOADB I/O 20 GND5 GND I/O GPIO6 ADC2 TMR2CLK TMR1ENMSK GPIO11 CTS MCLK TMR2IA.1 GPIO13 TMR2OA TMR1IA.3 I/O Analog I/O I/O Digital I/O ADC Input 2 External clock input of Timer 2 External enable mask of Timer 1 Digital I/O UART CTS handshake of Serial Controller SC1 SPI master clock of Serial Controller SC1 Capture Input A of Timer 2 Digital I/O Waveform Output A of Timer 2 Capture Input A of Timer 1 21(11) GPIO6 22(12) GPIO11 23(13) GPIO13 24(14) RESET RESET active low module reset (internal pull-up) GPIO14 GPIO14 TMR2OB TMR1IB.3 IRQB I/O Digital I/O Waveform Output B of Timer 2 Capture Input B of Timer 1 External interrupt source B 25(15) HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF Pin No. Pin Name 26(16) GPIO8 27(18) GPIO9 28(17) GPIO10 29 GND6 No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 9 of 33 DATE 25.10.2007 Datum Signal Name GPIO8 VREF_OUT TMR1CLK TMR2ENMSK IRQA GPIO9 TXD MO MSDA TMR1IA.2 GPIO10 RXD MI MSCL TMR1IB.2 Pin Type I/O Analog I/O I/O I/O I/O Digital I/O ADC reference output External clock input of Timer 1 External enable mask of Timer 2 External interupt source A Digital I/O UART transmit data of Serial Controller SC1 SPI master data out of Serial Controller SC1 I2C data of Serial Controller SC2 Capture Input A of Timer 1 Digital I/O UART receive data of Serial Controller SC1 SPI master data in of Serial Controller SC1 I2C clock of Serial Controller SC1 Capture Input B of Timer 2 GND I/O ground GPIO15 TMR1OA TMR2IA.3 IRQC GPIO16 TMR1OB TMR2IB.3 IRQD I/O I/O Digital I/O Waveform Output A of Timer 1 Capture Input A of Timer 2 External interrupt source C Digital I/O Waveform Output B of Timer 1 Capture Input B of Timer 2 External interrupt source D Description 30(19) GPIO15 31(20) GPIO16 32 GND7 GND I/O ground 33 VC1 VCONT Do not connect. (2) Internal control voltage for the power amplifier 34 GND8 GND I/O ground 35 GND9 GND I/O ground 36 GND10 GND I/O ground 37 GND11 GND I/O ground 38 GPIO7 GPIO7 ADC3 REG_EN I/O Analog Digital I/O ADC Input 3 External regulator open collector output Notes: (1) In case the onboard regulator option is mounted this pin is connected to the output voltage of the onboard regulator option and NOT to the output voltage VREG_OUT of the EM250. (2) VCONT is the internal amplifier gain control voltage, resistive external loading to ground can reduce the amplifier gain and therefore lower the maximum available module Tx output power. For most of the applications this pin is NOT connected and the amplifier is working at maximum gain. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF 7. BLOCK DIAGRAM Blockdiagramm VREG VBAT VBAT LDO or DC converter integrated antenna LDO rf terminal selection, filtering and U.FL socket matching circuitry RF transceiver 2,4GHz Tx BALUN Rx 16-bit XAP2b uC 128kB flash / 5k RAM RESET SIF RESET programming Rx/Tx switch 24MHz 32,768kHz (optional) KEY PARTS LIST Liste der Schlüsselkomponenten Part Name Teilenummer P.W.Board Leiterplatte Casing Deckel RF-IC part name RF IC Name 9. GPIO0 I/O PA pad EM250 GPIO16 1,8Vdc (optional) BALUN 8. No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 10 of 33 DATE 25.10.2007 Datum Material Material Glass cloth epoxide resin with gold plating FR4 mit Goldauflage Material: CuNi18ZN20, thickness 0.2mm Material: Weißblech 0,2mm Dicke EM250 from Ember Inc.(www.ember.com) All information are based on [2] chapter 28. TEST CONDITIONS Meßbedingungen Measurements shall be made under room temperature and humidity unless otherwise specified. Messungen unter normalen Bedingungen, Abweichungen sind gesondert notiert. Temperature Temperatur 25 ± 10°C 25 ± 10°C Humidity Luftfeuchtigkeit HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH 40 to 85%RH 40 to 85%RH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 11 of 33 DATE 25.10.2007 Datum 10. ABSOLUTE MAXIMUM RATINGS Absolute Grenzwerte The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. Item Punkt Symbol Zeichen Absolute Maximum Ratings Absolute Grenzwerte Unit Einheit Supply voltage VBAT -0.1 to +3.5 Vdc Voltage on any GPIO[16:0] , SIF_CLK, SIF_MISO, SIF_MOSI, SIF_LOADB, OSC32A, OSC32B, RESET, REG_OUT Vin -0.3 to VBAT+0.3 Vdc Storage temperature range Tstg -40 to +105 °C Operating temperature range Top -40 to +85 °C Input RF level Pmax dBm VTHHBM ±2 kV TDeath T.B.D. °C No. (1) ESD on any pin according to Human Body Model (HBM) circuit description Lead temperature Löttemperatur Notes: (1) Input must be current limited to the value specified. 11. OPERATING CONDITIONS Betriebsbedingungen VBAT = 3.3V, Tamb = 25°C , NORMAL MODE if nothing else stated No. Item Condition / Remark The typical value is recommended Symbol VDD Supply voltage RF Input Frequency fC RF Input Power pIN EM250 Tx power mode setting EM250 Tx output power setting EM250 Tx output power (2) setting EM250 Tx output power (2) setting To 5. corresponding typical module output power. For more details see part 14. Allowed Tx duty cycle Min Value Typ 2.7 3.3 2405 Unit Max 3.5 Vdc 2480 MHz dBm (1) NORMAL MODE or BOOST MODE external PA Channels 1-14 pOUTSET pOUTSET Channel 0 Channel 15 pOUTSET pOUT Channels 1-14 NORMAL MODE BOOST MODE Maximum output power set and 0dBi HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt and -43 +3 dBm -43 -3 dBm -43 -14 dBm -22 -21 +17,5 +18,5 dBm dBm 10 CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. Item Condition / Remark No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 12 of 33 DATE 25.10.2007 Datum Symbol Min Value Typ Unit Max Antenna (3) 10 Logic Input Voltage Low 11 Logic Input Voltage High 12 SPI clock rate 13 Operating temperature range pOUTT VIH The typical value is recommended 0.2x VBAT 0.8x VBAT VBAT 12 MHz +85 °C fSPI Top -40 Notes: ETRX2-PA is designed to comply to the standards and regulations listed in part 29. The conditions for compliance are: BOOST MODE is allowed with some restrictions : In order to stay within the output power limits 20dBm (EN300 328) and -30dBm PSD mask absolute (IEEE802.15.4) the power setting value is limited to 0dBm maximum for supply voltages above 3,3Vdc or operating temperatures below 0°C. (1) On the lowest channel 0 (2405MHz) and the highest channel 15 (2480MHz) the maximum allowed output power settings are limited to the maximum values stated above in order to not exceed the the spectral power density limits at the 2,4GHz I.S.M. band edges under extreme conditions as stated in part 4.3.3 “Frequency Range” of [1] (2) With these settings and duty cycles below 10% the limits for “Maximum Spectral Output Power density” according to part 4.3.2 of [1] are not exceeded. For lower antenna gain and/or lower Tx output power the duty cycle may be increased according to the formula in [1]. 12. DC ELECTRICAL CHARACTERISTICS conditions: VBAT = 3.3V, Tamb = 25°C, NORMAL MODE if nothing else stated No. Item Module supply voltage VBAT Internal regulated core voltage connected to (1) REG_OUT pin 2 Quiescent current, excluding internal RC oscillator Quiescent current, including 32,768kHz oscillator Transmit current consumption Transmit current consumption BOOST MODE Transmit current consumption Transmit current consumption Receive current consumption 10 Condition / Remark External load on internal Symbol Value Min Typ Max VBAT 2.7 3.3 3.5 Vdc 1.7 1.8 1.9 Vdc 0.8 3.0 uA 1.5 3.5 uA 106 120 mA 121 120 mA VCORE ISLEEP ISLEEP +17,5dBm module output power +18,5dBm module output power +10dBm module output power +0dBm module output power ITXVBAT ITXVBAT ITXVBAT ITXVBAT total IRX connected to IREG_OUT HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt Unit 63 mA 56 mA 37 mA CHECKED geprüft mA DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. Item Condition / Remark No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 13 of 33 DATE 25.10.2007 Datum Symbol Min regulated core voltage REG_OUT pin 2 Value Typ Unit Max (1) 0.2x VBAT Vdc 0.8x VBAT VBAT Vdc IIL -0.5 uA input current for logic 1 IIH 0.5 uA input pull-up resistor value RIPU 30 kΩ 15 input pull-down resistor value RIPD 30 kΩ 16 Output voltage for logic 0 17 Output voltage for logic 1 10 Input voltage for logic 0 11 input voltage for logic 1 12 Input current for logic 0 13 14 18 19 20 21 22 23 24 VIL VIH VOL VOH Output source current (standard current pad) Output sink current (standard current pad) Output source current (high current pad: GPIO[16:13] ) Output sink current (high current pad: GPIO[16:13] ) Total output current for I/O pads Input voltage threshold for OSC32A 0.18x VBAT Vdc 0.82x VBAT VBAT Vdc mA mA mA mA 40 mA IOHS IOLS IOHH IOLH IOH + IOL VIH_L VOH_L Output voltage level for VC1 0.2 0.18x VBAT 0.8x VBAT 0.82x VBAT Vdc Vdc (1) For more information about the internal regulated core voltage refer to part 5.7 in [2]. As the internal regulated core voltage at REG_OUT mainly feeds circuitry on ETRX2-PA, the REG_OUT module pin may only be slightly loaded and without feeding noise to REG_OUT. In case the dc regulator option is mounted REG_OUT is connected to the regulator option output instead and the internal regulated core voltage is not accessible. 13. A/D CONVERTER CHARACTERISTICS No Item ATD characteristics refer to datasheet EM250 part 5.5 ADC Module ATD timing/performance characteristics refer to datasheet EM250 part 5.5 ADC Module HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 14 of 33 DATE 25.10.2007 Datum 14. AC ELECTRICAL CHARACTERISTICS conditions: VBAT = 3.3V, Tamb = 25°C, NORMAL MODE measured with 50Ω terminal load at pin 38 RF or U.FL socket, for all channels number 11,12,..., 26 according to [1] No 10 11 Receiver Unit Limit Min Typ Max Sensitivity for 1% Packet Error Rate (PER) -85 -97 dBm Sens. for 1% Packet Error Rate (PER) BOOST MODE -85 -98 dBm dBm Saturation (maximum input level for correct operation, low gain) Adjacent Channel Rejection (1% PER and desired signal –82dBm acc. to [1]) Alternate Channel Rejection (1% PER and desired signal –82dBm acc. to [1]) Channel Rejection for all other channels (1% PER and desired signal –82dBm acc. to [1]) 802.11g rejection centered at +12MHz or –13MHz (1% PER and desired signal –82dBm acc. to [1]) Co-channel rejection (1% PER and desired signal –82dBm acc. to [1]) RF frontend filter attenuation for interferers in the range 1710-1910MHz Relative frequency error (2x40ppm required by [1]) Relative timing error (2x40ppm required by [1]) 30 dB 40 dB 40 dB 40 dB -6 dBc 30 dB -120 120 ppm -120 120 ppm 12 Linear RSSI range 40 50 dB 13 Spurious Emissions <1GHz -74 -57 dBm 14 Spurious Emissions >1GHz T.B.D. -47 dBm No Transmitter Limit Min Typ Max 14 15 17,5 18,5 20 Unit (2) 14 15 16 Output power at highest power setting NORMAL MODE BOOST MODE Output power at power setting -20dBm Output power at lowest power setting 17 Peak error vector magnitude as per IEEE802.15.4 18 Carrier frequency error 19 20 21 HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH dBm -22 dBm 10 -40 PSD mask relative at 3.5MHz distance from carrier Acc. to IEEE802.15.4 6.5.3.1 PSD mask absolute at 3.5MHz distance from carrier (2) Acc. to IEEE802.15.4 6.5.3.1 nd 2 harmonic at highest power setting dBm 35 40 ppm -20 -36 dB -30 t.b.d. dBm -60 APPROVED genehmigt -30 CHECKED geprüft dBm DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No 22 Transmitter rd 3 harmonic at highest power setting No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 15 of 33 DATE 25.10.2007 Datum Unit Limit Min Typ Max -52 -30 dBm 23 Spurious Emissions <1GHz -60 -36 dBm 24 Spurious Emissions >1GHz -57 -30 dBm No Standby Limit Min Typ Max 27 Spurious Emissions <1GHz -66 -57 dBm 28 Spurious Emissions >1GHz -66 -47 dBm No Sythesizer characteristics Limit Min Unit Unit Typ Max 29 Lock time from off state, with correct VCO DAC settings 100 uS 30 Relock time, channel change or Rx/Tx turnaround 100 us No Power On Reset (POR) Specifications Unit Limit Min Typ Max 31 VBAT POR release 1.0 1.2 1.4 Vdc 32 VBAT POR assert 0.5 0.6 0.7 Vdc 33 VCORE POR release 1.35 1.5 1.65 Vdc 34 VCORE POR hysteresis 0.08 0.1 0.12 Vdc HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 16 of 33 DATE 25.10.2007 Datum 14.1. TX POWER CHARACTERISTICS The diagrams below show the typical output power and module current dependency on module supply voltage and power setting, Condition NORMAL MODE. output power vs power setting 20 output power / dBm 15 10 -50 -40 -30 -20 -10 -5 0 3,5 10 -10 3,3 2,7 -15 -20 -25 -30 power setting / dBm module current vs power setting 120 current / mA 100 3,5 80 3,3 60 40 2,7 20 -50 -40 -30 -20 -10 10 power setting / dBm HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 17 of 33 DATE 25.10.2007 Datum 15. MECHANICAL REQUIREMENTS Mechanische Anforderungen No. Item Punkt Solderability Lötfähigkeit Resistance to soldering heat Limit Grenzwerte More than 75% of the soldering area shall be coated by solder Mehr als 75% der Lötfläche soll mit Lötpaste bedeckt sein. It shall be satisfied electrical requirements and not be mechanical damage HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt Condition Bedingung Reflow soldering with recommendable temperature profile See chapter 16.2 CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 18 of 33 DATE 25.10.2007 Datum 16. SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING) Temperatur-Zeit Profil für die Reflowlötung 16.1. FOR LEAD SOLDER 10 ±1s Recommended temp. profile for reflow soldering 30 +20/-10s 235°C max. Temp.[°C] 220 ±5°C 200°C 150 ±10°C 90 ±30s Time [s] 16.2. FOR LEAD FREE SOLDER Our used temp. profile for reflow soldering 30 +20/-10s Temp.[°C] 230°C -250°C max. 220°C 150°C – 190°C 90 ±30s Time [s] Reflow permissible cycle: Opposite side reflow is prohibited due to module weight. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 19 of 33 DATE 25.10.2007 Datum 17. MODULE DIMENSIONS Modulabmessungen No. Item Punkt Dimension Abmessung Tolerance Toleranz Width 20.50 ± 0.20 Lenght 37.50 ± 0.20 Height 2.80 ± 0.10 Remark Bemerkung With case 18. FOOT PRINT OF THE MODULE Lötpads vom Modul Dimensions in mm. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 20 of 33 DATE 25.10.2007 Datum 19. LABELING DRAWING Kennzeichnung des Moduls durch Label -PA The label dimensions are 13,0mm x 18,5 mm. It is suited for reflow soldering. comment: change ETRX2 to ETRX2-PA add CE logo to larger label if possible FCC ID: T7VEM250A Imprint Aufdruck ETRX2-PA Date Code 01 01Z Description Beschreibung This is the marketing name from Telegesis, the ENW number is only integrated in the 2D Code and marked with the Z Production Date Code in the format YYMMDD, e.g. 060602 Indication for software revision for our final test, customer are able to flash there own software. Indication for the hardware revision, Z indicates the ES status, will be removed after MP ready. 0000001 Indication for the serial number. FCC ID: TBD This is the FCC ID, should be labelled only after FCC approval. 2D-Barcode Information in the 2D-Barcode are the serial number [7 signs], the ENW-Part-Number [11 signs], identifier for the software release [2 signs], the identifier for the hardware release [2 signs] and the production date code in the format Year-Month-Day [6 signs], separated by a semicolon. The IEEE802.15.4 MAC Address [12 characters] are stored in the EM250, therefore it could not be on the label, but must be stored in the excel sheet to have a reference betweeen MAC address and serial number. 20. RECOMMENDED LAND PATTERN Empfohlenes Land Pattern This part will be included in next revisions. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 21 of 33 DATE 25.10.2007 Datum 21. SOFTWARE Software 21.1. SOFTWARE DECLARATION With the signature on the front page, customer clearly understand and agreed that the software, which is included in the module is only for testing purpose and Panasonic deny any responsibility for product liability, related to software matters. 21.2. SOFTWARE TOOLS In order to develop code and ZigBee® networks the Ember Insight Desktop Development Environment is required. This environment works with the preceeding EM2420, the EM250 and the EM260. For code development it comprises the Integrated Development Environment (IDE) named xIDE based on eclipse 3.1.0 for editing, compiling and debugging of C–applications. In addition network visualization and debugging tools are included. For programming the Ember Insight Adapter is required. This adaptor has to be linked to the computer where the Ember software tools are installed on. Before connecting ETRX2PA to the Ember Insight Adaptor study the latest Ember Insight Adaptor documentation. During programming or debugging the pins of ETRX2-PA have to be connected to the signals on the debug connector of the Ember Insight adaptor as shown in the table below. It is recommended to provide access to the programming pins of ETRX2-PA on the printed circuit board in order to allow software updates. ETRX2-PA pin ETRX2-PA signal name Insight Adapter signal name various ground ground 7(10) (1) VBAT 3.0Vdc 24(14) RESET RSTB 16 SIF_CLK SIF_CLK 17 SIF_MISO SIF_MISO 18 SIF_MOSI SIF_MOSI 19 SIF_LOADB SIF_LOADB as packet trace interface (PTI) also connect the following signals: 9(4) GPIO4 GPIO4 10(5) GPIO5 GPIO5 Note: (1) Only if the Ember Insight Adaptor is set to powering the target device ETRX2-PA. The pin numbers in brackets () are the related pins of the pin/header connector X5, which is only mounted for special plug versions. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 22 of 33 DATE 25.10.2007 Datum 21.3. EMBER ZIGBEE® STACK EmberZNet (currently available in versions 2.5.4 and 3.0.1) is the ZigBee® stack provided with EM250. It supports as networking topologies true mesh, star and cluster networks. The ZigBee® devices ZigBee® Coordinator, ZigBee® Router and ZigBee® End Device are supported. For the ease of application programming EmberZNet is controlled by the application over API commands. Direct ZigBee® APS layer APIs are provided for applications that require low level ZigBee® control. According to [1] each ZigBee® device has a unique address. This address is provided by Ember Inc. with the EM250. For more information on the items above see the website of Ember Inc. (www.ember.com) and the documentation included in the Ember Insight Desktop package as part of the Ember development kits. 22. RELIABILITY TESTS Zuverlässigkeitstests The measurement should be done after exposed to room temperature and humidity for 1hour. Die Messungen sollten erst nach einer Stunde Lagerung unter normalen Bedingungen erfolgen. No. Item Punkt Limit Grenzwerte Condition Bedingung a) Freq.:10~50Hz,Amplitude:1.5mm a) 20min. / cycle,1hrs. each of XYZ axis b) Freq.:30~100Hz, 6G b) 20min. / cycle,1hrs. each of XYZ axis Dropped onto hard wood from height of 50cm for 3 times -40°C for 30min. and +85°C for 30min.; each temperature 300 cycles Vibration test Electrical parameter should be in specification Shock test the same as the above Heat cycle test the same as the above Moisture test the same as the above +60°C, 90% RH, 300h Low temp. test the same as the above -40°C, 300h High temp. test the same as the above +85°C, 300h 23. APPLICATION NOTES Applikationshinweise 23.1. CAUTIONS FOR SAFETY Sicherheitshinweise These specifications are intended to preserve the quality assurance of products as individual components. Before use, check and evaluate their operation when mounted on your products. Abide by these specifications, without deviation when using the products.These products may shortHIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 23 of 33 DATE 25.10.2007 Datum circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then at least, provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 23.2. DESIGN ENGINEERING NOTES Designhinweise (1) Heat is the major cause of shortening the life of these products. Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum allowable. (2) Failure to do so may result in degrading of the product’s functions and damage to the product. (3) If pulses or other transient loads (a large load applied in a short time) are applied to the products, then before use, check and evaluate their operation when assembled on your products. (4) Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. (5) Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighbouring components. (6) If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. (7) These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. (8) These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. (9) In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. (10) In direct sunlight, outdoors, or in a dusty environment without a protective case. (11) In an environment where condensation occurs. (12) In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOx) (13) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. (14) Mechanic stress during assembly on board and operation has to be avoived. (15) Pressing on parts of the metal cover or fastening objects to the metal cover is not allowed. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 24 of 33 DATE 25.10.2007 Datum 23.3. STORAGE CONDITIONS Lagerbedingungen The module may not be stressed mechanically during storage. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: (1) Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX (2) Storage in direct sunlight (3) Storage in an environment where the temperature may be outside the range of 5°C to 35°C range, or where the humidity may be outside the 45 to 85% range. (4) Storage (prior to integration into your end product) of the products for more than one year after the date of delivery at your company if all the above conditions (1) to (3) have been avoided. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 25 of 33 DATE 25.10.2007 Datum 24. PACKAGING Verpackung 24.1. EMBOSSED TAPE / BLISTERGURT (1) Dimension of the tape / Abmessungen des Gurtes (EIAJ-tbd) (2) Cover tape reel strength / Abzugskräfte Blistergurt Deckfolie Force direction θ = 10deg Speed = 300mm/min. Cover tape reel strength =0.098~0.68N (10~70g) HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF (3) No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 26 of 33 DATE 25.10.2007 Datum Empty hollow / leere Taschen Direction of feed Vorschubrichtun Top cover tape Empty hollow more Component Empty hollow more than 10 pitch packed area than 10pitch more than 200mm Mehr als 10 leere Modulbereic Mehr als 10 leere Deckfolie groesser als Empty hollow in component packed area shall be less than two per reel and those hollows shall not be consecutive. Es dürfen minimal 2 leere Taschen im Bereich der Komponenten vorhanden sein, diese dürfen aber nicht aufeinander folgen. 24.2. COMPONENT DIRECTION Komponentenanordnung Top cover tape shall not be found on reel holes and shall not stick out from reel. Deckfolien darf nicht durch die Löcher der Spule und nicht außerhalb der Spule geführt werden. Tape running direction Laufrichtung des Bandes 12 Part No. (top view) Component direction Komponentenrichtung Figure 1 24.3. REEL DIMENSION Abmaße der Rolle (1) (2) Quantity per reel : 400 pieces Anzahl pro Rolle : 400 Stück Marking : Customer’s part No. / Quantity / Lot No. and Our part# with bar-code shall be on the reel. Kennzeichnung : Kundennummer / Anzahl / Losnummer und unsere Komponentennummer als Barcode wird auf die Rolle gedruckt Refer to figure 2 Bezugnehmend zur Zeichnung 2 HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 27 of 33 DATE 25.10.2007 Datum 24.4. PACKAGE Umverpackung (1) (2) Package box : Paketbox.: Marking : φ 13 +/-1 2 +/-0.5 φ 80 +/-2 φ 13 +/-0.5 Kennzeichnung : 1 or 2 reel (depends on quantity) 1 oder 2 Rollen (abhängig von der Liefermenge) Customer’s part No. / Quantity / Lot No. and Our part# with bar-code shall be on the package box. Kundennummer / Anzahl / Losnummer und unsere Komponentennummer als Barcode wird auf die Verpackung gedruckt Refer to figure 2 and 3 Bezugnehmend zur Zeichnung 2 und 3 Figure 3 Marking φ 330 Figure 2 HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH Marking 33.5 +/-1.0 2.0 +/-0.2 APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 28 of 33 DATE 25.10.2007 Datum 25. ORDERING INFORMATION Bestellinformationen MOQ Fehler! Ordering part number ENWCZA13A3EF gefunden werden. Fehler! Verweisquelle konnte nicht gefunden werden. ENWCZA14N2EF Fehler! Verweisquelle konnte nicht gefunden werden. ENWCZA15N4EF Fehler! Verweisquelle konnte nicht gefunden werden. Verweisquelle konnte nicht Description Engineering Sample ETRX2-PA with Ember IC EM250 ETRX2 with integrated ceramic antenna Engineering Sample ETRX2-PA with Ember IC EM250 ETRX2 with U.FL male socket Engineering Sample ETRX2-PA with Ember IC EM250 ETRX2 with RF out on a SMD pad Notes: Notes: (1) Abbreviation for Minimum Order Quantity (MOQ). ).If this module is in mass production the standard MOQ are 400 pieces, fewer only on customer demand. (2) As long as the module has engineering status, the ceramic antenna and the U.FL socket are mounted for all versions. The “Z” in the ordering part number indicates the engineering sample status. After mass production the “Z” will be changed to the “9”. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 29 of 33 DATE 25.10.2007 Datum 26. ROHS DECLARATION RoHS-Erklärung Declaration of environmental compatibility for supplied products: Hereby we declare to our best present knowledge based on declaration of our suppliers that this product do not contain by now the following substances which are banned by Directive 2002/95/EC (RoHS) or if contain a maximum concentration of 0,1% by weight in homogeneous materials for • • • • • Lead and lead compounds Mercury and mercury compounds Chromium (VI) PBB (polybrominated biphenyl) category PBDE (polybrominated biphenyl ether) category And a maximum concentration of 0,01% by weight in homogeneous materials for • Cadmium and cadmium compounds 27. DATA SHEET STATUS Datenblatt Status This data sheet contains data from the PRELIMINARY specification. Supplementary data will be published at a later date. Panasonic Electronic Devices (Europe) GmbH reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Please consult the most recently issued data sheet before initiating or completing a design. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 30 of 33 DATE 25.10.2007 Datum 28. REGULATORY INFORMATION 28.1. FCC NOTICE The device ETRX2-PA, including the ceramic antenna (ENWC9A05A3E) and the approved antennas, listed in Item 28.5, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 28.2. CAUTION The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Electronic Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help 28.3. LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is T7VEM250B. This FCC identifier is only valid for the part number ENWCZA13A3EF (ETRX2-PA with mounted ceramic antenna) or follows the OEM antenna installation instructions in Item 28.4. For details, please see the chapter 25. Ordering Information. The Final Device of an OEM as Composite Device: A composite device is subject to two or more technical rule parts and requires testing and labelling appropriately for each of the respective component rule parts. However, as a HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 31 of 33 DATE 25.10.2007 Datum practical rule, only one text or FCC logo need be labelled on a device. As a general rule the Declaration of Conformity (DoC) text statement is required over any Verification statement. For composites subject to DoC and Verification, or Certification and Verification, the labelling requirements for DoC or Certification need only apply. This does not remove the testing requirement for each individual device in a composite device. For composite devices subject to DoC and Certification, both the DoC logo and FCC ID (or FCC IDs when applicable) are required for composite DoC and Certified devices. Devices subject to DoC for both Part 15 and Part 18 may use only the Part 15 logo. For information to users, all relevant instructions that pertain to all components of a composite device are required. For example, Class A or Class B statements in Section 15.105; all warning statements and special instructions as required by Sections 15.21 and 15.27; and all Part 18 applicable instructions / attestations must be clearly stated. However, realistic variations in editing to clarify the language and structure are permitted as long as all the relevant points applicable to all of the components are represented. 28.4. ANTENNA INSTALLATION INSTRUCTIONS The related part number for this device is ENWCZA14N2EF (ETRX2-PA with mounted connector). For details, please see the chapter 25. Ordering Information. This device will be tested with an UFL connector from company Hirose and with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for this device will be available, after a first measurement with an approved antenna. 28.5. APPROVED ANTENNA LIST Note: We are able to qualify your antenna and will add to this list as that process is completed. Item Part Number Manufacturer Frequency Band Type Gain (dBi) FBKR35068-SM-KR EAD Ltd. 2.4GHz ½ Wave Dipole 2dBi (peak gain) FBTS35024-SM-ST EAD Ltd. 2.4GHz Wire 0dBi (peak gain) FBTS35024-SM-RA EAD Ltd. 2.4GHz Wire 0dBi (peak gain) HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 32 of 33 DATE 25.10.2007 Datum 28.6. RF EXPOSURE ETRX2-PA To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that the approved antenna in the previous table must be installed and/or configured to operate with a separation distance of 20cm or more from all persons to satisfy RF Exposure compliance. MPE calculation the maximum measured power output is 75mW (18,75 dBm). the maximum antenna gain is 2 dBi = numeric gain 1.58. Smax the maximum permissible exposure is defined in 47 CFR 1.1310 with 1 mW/cm². the distance of 20cm from the EUT's transmitting antenna where the exposure level reaches the maximum permitted level is calculated using the general equation: S= P*G / 4R² S = 0.024mW/cm² The internal / external antenna used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antennas or transmitter. This device is a Modular Approval to be used for fixed and mobile applications in the 2.4 GHz band and contains functions that are not operational in U.S. Territories. Portable applications or all application in 900 MHz band will be considered unauthorized equipment and will be required a separate FCC equipment authorization. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of ETRX2-PA with mounted ceramic antenna (FCC ID: T7VEM250B) is far below the FCC radio frequency exposure limits. Nevertheless, the ETRX2-PA shall be used in such a manner that the potential for human contact during normal operation is minimized. The EUT meets the requirements of FCC section 15.247. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 33 of 33 DATE 25.10.2007 Datum 29. RELATED DOCUMENTS Mitgeltende Dokumente [1] IEEE Standard 802.15.4 –2003 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [2] Data Sheet EM250, 120-0082-000F March 23, 2006, Ember Inc. (www.ember.com) [3] Data Sheet U.FL-Series 2004.2 Hirose Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height [4] ETSI EN 300 328 V1.5.1 (2004-03) Electromagnetic compatibility and Radio spectrum Matters (ERM) HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt CLASSIFICATION PRODUCT SPECIFICATION Einstufung Produktspezifikation SUBJECT MODEM FOR IEEE802.15.4 (ZIGBEE) Thema “ZigBee” Modem“ (IEEE802.15.4) CUSTOMER’S CODE PANASONIC’S CODE ETRX2-PA ENWC9A13A3EF / ENWC9A16A3EF No. REV. DS-ETRX2-PA-2400-102 PAGE Seite 34 of 33 DATE 25.10.2007 Datum 30. GENERAL INFORMATION Allgemeine Informationen © Panasonic Electronic Devices (Europe) GmbH 2006. All rights reserved. This product description does not lodge the claim to be complete and free of mistakes. Please contact the related product manager in every case. If we deliver samples to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and there may be differences to be published Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic Electronic Devices (Europe) GmbH rejects any liability or product warranty for Engineering Samples. In particular, Panasonic Electronic Devices (Europe) GmbH disclaims liability for damages caused by • the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in an other product to be sold by Customer, • deviation or lapse in function of Engineering Sample, • improper use of Engineering Samples. Panasonic Electronic Devices (Europe) GmbH disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. 31. LIFE SUPPORT POLICY Politik für Lebenserhaltungssysteme This Panasonic Electronic Devices (Europe) GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Electronic Devices (Europe) GmbH for any damages resulting. HIGH FREQUENCY PRODUCTS DIVISION Module Business PANASONIC ELECTRONIC DEVICES (EUROPE) GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 34 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:0c084dff-391f-47d1-9da2-d8f1b74921e6 Producer : Acrobat Distiller 6.0.1 (Windows) Company : EuTC Source Modified : D:20071025163639 Creator Tool : Acrobat PDFMaker 6.0 für Word Modify Date : 2007:10:25 18:41:36+02:00 Create Date : 2007:10:25 18:36:58+02:00 Metadata Date : 2007:10:25 18:41:36+02:00 Document ID : uuid:8409cfe5-3430-4ae5-954a-592c32bb872e Format : application/pdf Title : 1 Creator : Schoss Tagged PDF : Yes Author : SchossEXIF Metadata provided by EXIF.tools