Parker Hannifin MSLINK0006 200 Series Radio Module User Manual Exhibit D Users Manual per 2 1033 b3
Lord Corporation 200 Series Radio Module Exhibit D Users Manual per 2 1033 b3
Exhibit D Users Manual per 2 1033 b3
200 Series Radio Module Integration Guide 1. Overview The 200 Series Radio Module is an OEM device used to acquire data from LORD Corporation wireless sensing devices. It is designed to be embedded in other products to provide radio communication and data passthrough capabilities in a modular format. It is designed to be used with LORD data acquisition software or user software developed using the LORD MSCL code library. The module includes an integrated microcontroller/radio transceiver that communicates to LORD devices in the 2.4 GHz band. There are two radio transmission protocols that are available on the radio module – the standard 802.15.4 protocol (LXRS) and a LORD proprietary protocol (LXRS+). The modes are selectable in the LORD software. Both are capable of lossless transmission of continuous, burst, and other sampling modes, depending on the node capabilities. The increased radio transmission rate of the LXRS+ protocol results in faster network throughput, and the ability to handle larger data packets. However, because of the increased packet size, the packet error rate will likely increase (reducing RF sensitivity) and effectively reducing the RF range. 2. Integration The radio module requires a PCB carrier board for proper integration. This board can be designed by LORD, or by an OEM customer with the information provided in this document. The carrier board provides power (+5 Vdc +/- 2%, 50mA) to the radio module, as well as the serial and input/output interface to connect the microcontroller to the larger communication system. The microcontroller code required to control the radio module is proprietary and is developed at LORD. The following section describes physical layout and pin configuration of the module. The module is 0.98” x 0.53”. It has an internal antenna on one end of the board. The interface to the carrier board is through solder pads around the three other sides of the board. For exact layout dimension of these pads, contact LORD Technical Support for an engineering file. The radio module is an OEM circuit board intended to be housed in an enclosure of the type suitable for the final product. It has no environmental protection by itself. Operating temperature range is -40 to +85 °C. LORD Corporation 9/26/2017 Prepared by J. Dunklee Physical Interface Internal antenna location Carrier board solder pads (around board edge) Dimensions in inches LORD Corporation 9/26/2017 Prepared by J. Dunklee Pin Interface Radio Module Signal name pin number Description 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Digital ground Microcontroller reset Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Serial Wire Debug trace data output Serial Wire Debug data in/out Serial Wire Debug clock Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Digital ground Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Digital ground Module power input +5V dc Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Status LED red Status LED blue Status LED green Microcontroller general purpose I/O Digital ground LORD Corporation DGND EFR32MG RESET PF7 PF6 PF5 PF4 PF3 DBG_SWO DBG_SWDIO DBG_SWCLK PC11 PC10 PC9 PC8 PC7 PC6 DGND PD10 PD11 PD12 PD13 PD14 PD15 DGND VCC PB15 PB13 PB12 PB11 PA5 PA4 LED_RED LED_BLUE LED_GREEN PA0 DGND 9/26/2017 Prepared by J. Dunklee 3. Regulatory a. Radio modules must be labeled with the corresponding FCC/IC ID number. Product assemblies with radio modules in them must be labeled “Contains 200 Series Radio Module” followed by the FCC/IC ID. b. The following notice applies to the radio module and must also appear in its entirety in the final product user manual. In addition, based on the antennas and power parameters specified for this device, it must be operated at least 2.16 cm from the operator to ensure RF levels do no exceed what is considered healthy for human exposure. LORD Corporation 9/26/2017 Prepared by J. Dunklee
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 4 Language : en-US Tagged PDF : Yes Author : Chris P. Townsend Creator : Microsoft® Word 2013 Create Date : 2017:09:26 16:46:34-04:00 Modify Date : 2017:09:26 16:46:34-04:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools