Paxton Access 337937 Net2 Entry - VR Panel, surface mount User Manual

Paxton Access Ltd Net2 Entry - VR Panel, surface mount manual

a href="https://usermanual.wiki/Paxton-Access" itemprop="url"> Paxton Access >

manual

Page 105/10/2013Ins-30208-US Net2 Entry - Vandal Resistant PanelTechnical SupportTechnical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)1.800.672.7298 supportUS@paxton-access.comDocumentation on all Paxton products can be found on our web site - http://www.paxton-access.com/PaxtonThe Net2 Entry panel is a robust door entry panel incorporating both door entry and access control functions. It is powered using power over Ethernet (PoE) and communicates with the other elements of the system using IPv6, providing 'plug and play' installation. Each panel is associated with a Net2 Entry control unit which is the interface to the door hardware. Description of productThe panel is equipped with a keypad and a proximity token reader. A resident can use either the keypad or a token to gain entry. Installers gain access to the menu options using an engineer code or an engineer token.Net2 software is used to administer the access control functions. It must be v4.25 or a later version. 1. Speaker2. Proximity reader3. Keypad4. LCD display5. IR LEDS for night time operation6. Microphone7. Color camera8. Light sensor24516783
Page 2Decide how the units are to be connected. You can either run your own wired network or share the buildings existing data network. If using the owners network, the system uses IPv6 protocol and PoE (Power over Ethernet) so the network must support this switch type.InstallationMountingThe unit is supplied with the surface mount backbox. A ush mount backbox is also available (PN:337-857). Screws and wall plugs are provided in the tting kit.SURFACE BACKBOXFLUSH BACKBOXA single hole must be drilled for the single data/power connection. Electrical power is supplied via the data cable (PoE) from the Net2 Entry controller.1. Determine the height for the camera and then mark and drill the cable hole with reference to the diagram.2. Complete the installation of the mounting backbox - Surface or Flush.3. Connect the Net2 Entry panel to controller.4. Mount the panel in its backbox.5. Power up the panel from controller supply (PoE) or external PoE switch.The display will ask you to set up an Engineer code. The panel checks to see if any monitors also exist on the network. Any that are detected will now have the engineer code loaded and will store the panel ID that called themTo achieve the best camera performance, try to mount the panel facing away from direct sun or a bright light source. This will also help the user to read the LCD display.Where it is not practical to run a patch cable to the rear of the unit, it can be directly wired to the network cable via the supplied IDC module. Paxton recommend that the network cable is run to each location and terminated in a network box. A patch cable should then be used to link the unit to the network. This makes unit replacement or removal for building maintenance much easier.AA36839.57944 51 79 75Ø5x 81361718533030.53291327939.544 51 79 75Ø5x 840.532.5
Download:
Mirror Download [FCC.gov]
Document ID1991623
Application ID8c6mkevUVENYAV+Np0jDcg==
Document Descriptionmanual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize127.39kB (1592415 bits)
Date Submitted2013-06-14 00:00:00
Date Available2013-06-14 00:00:00
Creation Date2013-05-10 12:26:57
Producing SoftwareAdobe PDF Library 10.0.1
Document Lastmod2013-05-10 14:47:01
Document Titlemanual
Document CreatorAdobe InDesign CS6 (Windows)
FCC ID Filing: USE337937

Navigation menu