Paxton Access Z99UV30 Proximity Vandal Proof Reader User Manual INSTRUCTION PROXIMITY vandal proof reader
Paxton Access Ltd Proximity Vandal Proof Reader INSTRUCTION PROXIMITY vandal proof reader
User Manual
02/02/2010 Ins-30092-US PROXIMITY vandal proof reader Paxton Technical Support 1.800.672.PAXT Technical help is available: support@paxton-access.com Monday - Friday from 12:00 AM - 5:00 PM (PST) Saturday from 1:00 AM - 5:00 AM (PST) Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/ Fitting Open hole - medium vandal resistance Cement plug - high vandal resistance Blind hole - very high vandal resistance Wiring Connection to a control unit reader port Connection modules Reader junction box (325-020-US) This module can be used to provide a connection point for the reader RJ45 plug. The terminals on the module are then wired color for color to the controller. Alternatively, the reader can be wired directly into the screw terminals of the control unit by first cutting off the RJ45 plug and stripping back the wires in the cable. Reader Port Module (325-030-US) This module may be purchased separately to speed up the installing and replacement of readers. The reader port module is designed to convert the standard reader ports on Switch2 and Net2 controllers to accept one or two RJ45 connections. Pull off the screw terminal block from the reader port and simply replace it with this module. Further information on how to purchase Installer Tools is available at: http://paxton.info/841 Cable extensions Readers can be extended using Belden CR9540 10-core overall screened cable to a maximum of 100 yards. Technical Help Here is the list of topics about this product that receive the most technical support inquiries. We list them here to help you speed up the installation and trouble shooting process. 1 - Readers/Keypads not working. Q- Software settings - Confirm that the settings of the reader or keypad are correct. Q- Connections - Check the wiring and integrity of the connectors. If possible, test this reader on the other port. Q- Cable - Belden 9540 should be used to extend the reader cable (100yds maximum). Twisted pair alarm cable Q should not be used. To confirm that an extended reader cable is not at fault, wire the reader directly to the port. Q- Supply voltage - Confirm that the voltage is within specification. (see table) Q- User token - Confirm that the user token used for testing is OK by presenting it to a known working reader. Q- Interference - Confirm whether the reader works when tested ‘in hand’ and not mounted on the wall. Q Ensure PROXIMITY readers are not mounted back to back or that there is no interference from other RF devices. 2 - Readers / Keypads - Extending cable. QOnly Belden CR9538 / 9540 can be used for cable extensions. CR9538 8 core for up to 25yds, CR9540 10 core for Q25-100yds (maximum extension). With CR9540, the two additional cores should be used to double up the power. 3 - Net2. What to do if a user has no access - Check the reader LEDs when a card is shown. QQQQQ Q- No LEDs - the reader has no power. No change in display - try the card on a known working reader. If there is still no response, replace the card. Green LED flashing when a card is presented; check relay 1 LED to check for activity and also the lock wiring. Red LED is flashing when a card is presented; check the validity of the user at the PC. Check user’s access level and ensure they should have access by clicking on Current Validity. Check the ‘Valid Until’ date and confirm this has not expired. Reinstate the ACU from the doors screen. Select the ACU’s you wish to reinstate and then click OK. 4 - Switch2 - Adding an additional card pack. QYou need to be in possession of the original enrolment card. Present the original enrolment card to the reader and Qthe Amber LED will flash, Green & Red LEDs will be off, then present the Enrolment card from the new card pack; Qthe reader will beep and all LEDS will be lit. The additional cards will now be valid. Repeat this with each reader Qand with any additional card packs. Any valid enrolment card can be used to add further packs. This is the same Qfor enrolling function card packs onto a system. 5 - Switch2 - How to reset the controller. Q1. Q2. Q3. Q4. Q5. Disconnect the power and remove the wires from the Green and Mauve terminals Insert a wire link between the Green and Mauve terminals Reconnect the power (the unit will bleep 4 times) Disconnect the power and remove the link wire, reconnect the Green and Mauve wires Reconnect the power (the unit will bleep 3 times per second). The unit is ready to be enrolled. Suitability Security sensitive doors Mounted on metal surface Wet environments Readers mounted together 12 inches between readers Specifications Environment Operating temperatures - all items Waterproof Min Max -20 °C (-4 °F) +55 °C (+131 °F) IPX7 Outdoor Use Cable length Electrical Voltage 5 yards Min Max 8V DC 14V DC 100 mA Current Carrier frequency 125 kHz Clock and data bit period Dimensions 600 µs Diameter 3/4 Read Range inch Depth 2 3/8 inch Token Keyfob Hands Free Token 3 inch 1 1/2 inch Not Compatible FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This product is not suitable for retail sale. All warranties are invalid if this product is not installed by a competent person.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 4 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:9b81d6ae-72b8-46f0-86d7-bde55c07befb Producer : Adobe PDF Library 7.0 Trapped : False Create Date : 2010:02:02 09:31:28Z Metadata Date : 2010:02:02 09:32:25Z Modify Date : 2010:02:02 09:32:25Z Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 6818 bytes, use -b option to extract) Instance ID : uuid:04f793b6-4411-4ca3-bdd6-b315779ada74 Rendition Class : proof:pdf Document ID : adobe:docid:indd:26017022-3879-11dd-9017-f53194c60f2a Derived From Instance ID : 2b6a3e85-386d-11dd-a08b-af5ca5031f74 Derived From Document ID : adobe:docid:indd:716cf8f9-3866-11dd-a08b-af5ca5031f74 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 300.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:4467A890C362DD119393AEDE0CDB153A, uuid:a27c06a5-0165-4819-8b7c-c5a8e9794cd2, uuid:fab4ca5b-3ae9-4c1b-99d7-6b10bf1e5afb, uuid:aeadde7f-13a3-4fea-82b6-904946c6b105 Manifest Reference Document ID : uuid:C18CBA7D2100DF11AE179FBCC0B84ED9, uuid:1d686997-20a0-4ddc-851b-cce15bb5b5da, uuid:8AA8E00AD99CDC1194088FCA155C3878, uuid:ba4656aa-3d5c-4c16-8aa2-eee89a1c50c8 Format : application/pdf Title : INSTRUCTION - PROXIMITY vandal proof reader Tagged PDF : Yes Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools