Installation Directions

: Pdf 102659-Installationsheet 102659-InstallationSheet 662057 Batch5 unilog

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

DP/OP/PR/SK/SP Series
Installation Instructions, Standard or Slot Grid Ceiling Systems
Page 1 of 2

1

Access Plate
Remove Access Plate by sliding Access Plate in the direction of Arrow 1. To remove, lift up and slide in the direction of Arrow 2. Bend Fixture Tab up out of body and
make ground and ballast connections. Bend Fixture Tab
back to original position. Replace Access Plate by reversing removal instructions.

1.

Access Plate Opening
Ground Screw

Access
Plate

Access Plate
Opening

Fixture Tab

2.
Tab
Access Plate Opening

2

3

For individual fixtures, beginning or end of row, assemble
End Trim (full trim) as shown.
Assemble Corner Spline (1) to End Trim by inserting Corner
Spline into end of End Trim. Remove Protective Covering from
Double Face Tape (fastened to End Trim). Insert Corner Spline
(2) into end of Side Trim.
On Overlay and Plaster Frame type, End Trim must be assembled before fixture is installed.
Note: Louver must be removed before installing fixture into
ceiling.
For continuous row mounting use Half Trim (must be ordered
separately from factory) and replace Hex Head Screws with Flat
Head Screws provided in Half Trim Supply Pack.

Louver and Lens Frame Installation
Place hinge in hinge slot on side rail of Fixture. Be sure
hinge is seated in hinge slot properly. Rotate Free Edge
up into Fixture and secure with Spring Loaded Latches.
To remove Lens Frame, push leg on Spring Loaded
Latches towards center of Fixture and reverse installation
instructions.

Side Trim
2
1

2

1

Corner
Spline

End Trim
(full trim)

Louver

Double Face
Tape/Covering

Housing

4

For DPA/DPS fixtures
To open Louver, place finger between T-bar and Louver.
Press Spring Latch (each end) towards center of the
fixture. To close, swing Louver up and secure with Spring
Latches.
Spring Latch
T-bar
Louver

Louver

Spring Latch

Fixture

5

SP Door Frame
For relamping open Door Frame by pressing Spring
Latch in the direction of the arrows (both ends of Door
Frame). Lift Door Frame to clear Hinge from Hinge Slot.
To replace Door Frame, reverse the procedure.
Hinge Slot

Hinge

Spring
Loaded
Latches
Free Edge
Spring Latch
Door Frame

01/10
45 Industrial Way, Wilmington, MA 01887 (978) 657-7600 • Fax (978) 658-0595
We reserve the right to change details of design, materials and finish. www.lightolier.com
This product may have a mercury containing lamp. Manage in accordance with Disposal Laws.
See: www.lamprecycle.org
59-30907-002 Rev. A

DP/OP/PR/SK/SP Series
Installation Instructions, Standard or Slot Grid Ceiling Systems
Page 2 of 2

6

Opalescent, Prismalyte Plus or Skyway Door Frame
For relamping, open Door Frame by pushing up on the
Spring Latch, (both ends of Door Frame) then lift Door
Frame to clear Hinge from Hinge Slot. To replace the
Door Frame, reverse procedure.

7

Earthquake Clip (For 1'x4' only)
Angle Fixture up into ceiling opening, resting Fixture on
Ceiling Tees (by others). With Screw (by others) secure
Earthquake Clip to Fixture with Ceiling Tee (by others)
between Earthquake Clip and Fixture as shown.
Screw (by others)

Hinge Slot
Earthquake
Clip
Fixture (End Cap)

Ceiling Tee
(by others)

Hinge
Screw
(by others)

Door Frame

Earthquake
Clip

Ceiling Tee (by others)
Spring Latch

8

Earthquake Clip (For 2' X 2' / 2'x4' only)
Swing-out Built- Angle Fixture up into ceiling opening with Built-in Earthquake
Clips (in the opened position) resting on Ceiling Tees (by othin Earthquake
ers). Bend Built-in Earthquake Clips back flush against CeilClips at each
ing Tee (by others) and secure with Screw (by others).
end of Fixture.

Fixture

Built-in Earthquake
Clip (opened position)

Ceiling Tee
(by others)

Built-in Earthquake Clip
(opened position)

Screw (by others)

Built-in Earthquake Clip
(before installation)
Fixture

Fixture

Built-in
Earthquake
Clip

Fixture
Ceiling Tee
(by others)

9

Optional Air Closure Strip (Air Handling 1'x4' / 2'x2' / 2'x4')
Air Closure
Strip

Air
Vent
(Fixture)

To blank out air, install Air Closure Strip

Air Closure
Strip

Cover Air Vents with Air Closure Strip
and slide in direction of arrow until Air
Closure Strip locks into place

Air Closure Strip
Factory Installed. Catalog Number Suffix:
ACS2 (2'x 2' Units); ACS4 (1'x 4', 2'x 4' Units)
Field Installed. Catalog Number Suffix:
ACS2 CSP (2'x 2' Units), ACS4 CSP (1'x 4', 2'x 4' Units)

45 Industrial Way, Wilmington, MA 01887 (978) 657-7600 • Fax (978) 658-0595
01/10
We reserve the right to change details of design, materials and finish. www.lightolier.com
This product may have a mercury containing lamp. Manage in accordance with Disposal Laws.
See: www.lamprecycle.org
59-30907-002 Rev. A

Air Closure
Strip
Air Vent
(Fixture)
Fixture



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Mode                       : UseThumbs
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:30
Create Date                     : 2010:01:22 13:40:20Z
Creator Tool                    : QuarkXPress(R) 7.0
Modify Date                     : 2010:01:22 13:57:08-05:00
Metadata Date                   : 2010:01:22 13:57:08-05:00
Producer                        : QuarkXPress(R) 7.0
X Press Private                 : %%DocumentProcessColors: Black.%%EndComments
Format                          : application/pdf
Title                           : Layout 1
Document ID                     : uuid:cff178af-e313-9d43-af4b-dbf8ba50952c
Instance ID                     : uuid:dd827508-edf6-6348-a8af-fb4c19cc304e
Page Count                      : 2
Creator                         : QuarkXPress(R) 7.0

EXIF Metadata provided by EXIF.tools