913_07 165D7996P001 GE Dishwasher Mini Manual 31 30463
2013-04-09
: Pdf Ge Dishwasher - Mini Manual - 31-30463 GE Dishwasher - Mini Manual - 31-30463 GE, Camco, Hotpoint, Mofat
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
SERVICE INFORMATION — DO NOT REMOVE 165D7996P001 IMPORTANT SAFETY NOTICE THIS INFORMATION IS INTENDED FOR USE BY INDIVIDUALS POSSESSING ADEQUATE BACKGROUNDS OF ELECTRICAL, ELECTRONIC AND MECHANICAL EXPERIENCE. ANY ATTEMPT TO REPAIR A MAJOR APPLIANCE MAY RESULT IN PERSONAL INJURY AND PROPERTY DAMAGE. THE MANUFACTURER OR SELLER CANNOT BE RESPONSIBLE FOR THE INTERPRETATION OF THIS INFORMATION, NOR CAN IT ASSUME ANY LIABILITY IN CONNECTION WITH ITS USE. DISCONNECT POWER BEFORE SERVICING IMPORTANT – RECONNECT ALL GROUNDING DEVICES IF GROUNDING WIRES, SCREWS, STRAPS, CLIPS, NUTS OR WASHERS USED TO COMPLETE A PATH TO GROUND ARE REMOVED FOR SERVICE, THEY MUST BE RETURNED TO THEIR ORIGINAL POSITION AND PROPERLY FASTENED. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel – DO NOT contact the following parts while the appliance is energized: heating element, water valve, main pump and drain pump and active vent motor (if present). WASHABILITY COMPLAINTS Hot Water – Ample supply of water at 120°F minimum temperature is necessary. Do not use dishwasher soon after using clothes washer or filling bathtub. Loading – Consult Owner’s Manual on loading procedures. Amount of Water – Make sure dishwasher is level. Check water level, allowing dishwasher to fill normally for first fill. The water level should be to the center of the float dome. If water level is low, check for clogged screen in water valve and check float switch. Detergent Module Leakage – Some moisture in cup is normal. Detergent must not be soaking wet, oozing out and down the inner door panel. If a leak is detected, check detergent module door lid, latch operation, and gasket seal. ® FILTER AND DRAIN SYSTEM TO SERVICE WASH ARM ASSEMBLIES: Will Not Pump Out 1. Enter service mode and check drain pump operation (see service mode). 2. Check cover inlet (Figure 3) in the bottom of the tub. Make sure that it is clear of food particles. 3. Check for blocked or partially blocked drain line and air gap. 4. Check routing of drain hose system. It must be free from kinks. 5. Remove lower spray arm (Figure 3). 6. Remove main conduit mounting screw (Figure 3). 7. Lift main conduit tab, pull and rotate main conduit out of hub (Figure 3). 8. Remove the cover inlet, check sump and drain outlet (Figure 3). It may be blocked by a toothpick or other object. 9. Check drain pump valve (Figure 1) for correct operation. Water should flow only from the pump to the high drain loop. 10. Drain line check valve (Figure 1) must pass water in the drain line direction only. Check Wash Arms 1. Check holes in spray arm for bits of Nut china, seeds and other foreign matter. Bearing 2. Check spray arms for rotation. MOTOR-PUMP MECHANISM Motor Stalled-Hums 1. Disconnect Power. Try to turn motor shaft clockwise to determine if seal is stuck and can be broken loose. If motor shaft cannot be turned, cutter blade may be bound up. Proceed to step 2. 2. On inside of dishwasher, remove the cover inlet (Figure 3) and reach down into the sump (Figure 1). Check for blockages such as bone, wire ties, etc. If it contains debris, clean thoroughly. If motor shaft cannot be turned, remove mechanism. To Remove Motor-Pump Mechanism: 1. Remove cover inlet (Figure 3). With syringe, remove all water from sump (Figure 3). 2. Loosen main pump clamp and pump connector clamp (Figure 1). 3. Remove hanger that holds motor to tub frame (Figure 1). 4. Motor-pump mechanism can now be removed from under dishwasher. Drain Line Check Valve Water Valve Flood Switch Main Pump Clamp CALROD HEATING ELEMENT To Remove Heating Element (Figure 4): Middle Spray Arm 1. Disconnect Power and remove wire leads from heating element. 2. Unscrew two heating element nuts. 3. Remove heating element supports. 4. Lift and remove heating element. To Disassemble Mid-Level Arm (Figure 2): Hub 1. Pull upper rack Mid Screw Bracket Tab all the way out. (Optional) Upper Rack 2. Remove nut on bottom of mid arm. This will allow the mid arm and bearing to be removed. 3. To remove conduit, remove screw (some models) from hub. Press tab on Mid Conduit side of mid Conduit Carrier bracket to release the hub and mid conduit. Figure 2 4. To reinstall arm, reverse procedure. NOTE: Mid arm to be installed with spray jets facing the upper rack. Bearing to be placed between nut and bottom of mid arm. Heating Element Heater Grommet Tub Nut Heating Element Support Figure 4 To Remove Lower Arm and Fine Filter Assembly (Figure 3): 1. Remove lower rack from dishwasher. 2. Gently lift and rotate lower spray arm counter clockwise to remove. 3. Rotate nut hub counterclockwise to remove. Gently lift fine filter assembly up. Remove fine filter drain from sump. 4. Clean fine filter screen if soil is present. 5. To reinstall fine filter and lower spray arm reverse procedure. NOTE: When installing fine filter make sure the drain port of the filter is engaged with the drain for the fine filter. Motor Pump Connector Hanger Clamp DOOR COMPONENTS (Figure 5) The door components are accessible by removing three screws from each side of inner door and two screws at the bottom of the door. Carefully separate the inner door panel from the outer door panel. The active vent can be accessed by removing the screws on the escutcheon. Flapper Lower Spray Arm Main Conduit Mounting Screw Proper Amount of Detergent – Use full detergent cup of fresh detergent in hard water. Use only enough detergent to get good wash performance in soft water. Main Conduit Fine Filter Drain Port Rinse Agent – Use rinse agent if spotting is a problem. Water Valve – Check valve for intermittent operation. Valve coil can be direct tested. Allow to heat normally, then check to see if coil opens. Active Vent Electronic Control Interlock Switch Assembly Nut Hub Detergent Module Drain For Fine Filter Fine Filter Assembly Spray Arm – Check to be sure spray arm spins freely and jets are not clogged. Cover Inlet High Drain Loop Figure 1 Drain Pump Drain Pump Valve Sump Coarse Filter Turbidity Sensor Figure 3 Hub Main Conduit Tab Figure 5 Harness Float Dome N.D. 913-07 Pub. No. 31-30463 J5-1 WR NTC 1200-2800 YB NX SX OX L1 N 10 M CIRCULATION PUMP 725-1200 WR WR WATER VALVE WR 19.4-19.8 HEATING ELEMENT G DOOR INTERLOCK WR WX NO COM 30 M NX FLOOD SWITCH YX PX C NO VX RX DRAIN PUMP 1200-2800 WR WR BW NO BX COM DOOR INTERLOCK 1 2 3 4 TURBIDITY SENSOR RY J2-6 30 DETERGENT MODULE DETERGENT MODULE RX J2-5 DRAIN PUMP J5-2 J2-4 VENT MOTOR RX M M 19.4-19.8 J2-3 J2-1 PUMP MOTOR C HEATING ELEMENT NX NO VX 10 M PUMP HEATING ELEMENT BX WR WR WR WR 725-1200 WATER VALVE FLOOD SWITCH PX J2-2 WATER VALVE BX BW J2-8 J1-3 THE "X" INDICATES ONE SOLID COLOR- NO TRACER. WIRES WITH TRACER SHOW BOTH COLORS. EXAMPLE -WR IS WHITE WITH RED TRACER. LETTERS RX LT. BLUE SX BLACK TX BROWN VX DK. BLUE WX ORANGE YX PINK COLOR COLOR CODE COLOR RED GRAY TAN PURPLE WHITE YELLOW ---THIS CIRCUIT NOT IN ALL MODELS 3-DIGIT DISPLAY LETTERS AX BX CX NX OX PX DOOR BW NO COM YX 115V 60HZ RY **NOTE : Component will be activated for indicated time. Component may be deactivated by pressing the same keypad that was pressed to activate the component. DETERGENT MODULE FLAT BOWED FLAT BOWED FLAT BOWED FLAT BOWED FLAT BOWED RX Activates Drain Pump 75 Activates Detergent Module Activates Detergent Module 2L 60 Activates Main Pump Activates Main Pump 3L 75 Activates Heating Element Activates Heating Element 4L 300 Activates Drain Pump Activates Water Valve 5L 50 or 71 (Length of time is model dependent) START/RESET Used to EXIT Service Mode Keypads to the right of the Start/Reset keypad (Enhancement/Extras) Activates the following in order: Status LEDs; Wash LEDs; 1R FLAT Start/Reset and Option LEDs; 3 seconds each cycle BOWED finally “888” will be shown on the 3 digit display (some models) FLAT 2R Opens Active Vent BOWED FLAT 3R Closes Active Vent BOWED 1L M Keypads to the left of the Start/Reset keypad (Selections) ACTIVE VENT MOTOR TIME in seconds** *NOTE : Service mode may be used for 30 minutes maximum. After 30 minutes the service mode will automatically turn off. 3 POWER J1 2 SUPPLY 1 4R J2-7 3R POWER SWITCHING J2 1 2 3 4 5 6 7 8 DESCRIPTION 2R TO EXIT SERVICE MODE : PRESS THE START/RESET KEYPAD AT ANYTIME TIME TO EXIT. KEYPAD CONTROL TYPE 1R Indicates Keypad Used Only on Some Models TRITON XL SERVICE MODE TEST MATRIX * PAD START RESET PQA J10 1 2 3 1L J1-1 DOOR WR WX COM NO 2L 3-DIGIT DISPLAY J5 J8 1 ACTIVE 2 VENT 1 2 3 4 5 6 7 8 9 10 3L BX TO ENTER SERVICE MODE : PRESS THE COOKWARE (POTS & PANS ON SOME MODELS) AND THE HEATED DRY KEYPAD SIMULTANEOUSLY FOR 3 SECONDS. 4L Vcc Indicates Keypad Used Only on Some Models 5L TRANSMITTER CATHODE 4R CONTROL CIRCUIT BOARD 3R J7 KEYPAD 2R NTC 1R RECEIVER EMITTER START RESET 1 2 3 4 1L YB NX SX OX 2L 1 TURBIDITY/ 2 TEMPERATURE SENSOR J3 3 4 3L K E Y P A D 4L WARNING: POWER MUST BE DISCONNECTED BEFORE SERVICING THE APPLIANCE. 5L 165D7995P001 BOWED PANEL FLAT PANEL BX THIS DISHWASHER IS PROGRAMMED WITH A SERVICE MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING THE DISHWASHER. EACH COMPONENT MAY BE CYCLED TO DETECT IF IT IS FUNCTIONING CORRECTLY. COMPONENTS ARE CYCLED BY PRESSING KEYPADS TO THE RIGHT OR LEFT OF THE START/RESET KEYPAD. DETERMINE WHICH TYPE OF CONTROL PANEL IS PRESENT (FLAT OR BOWED) AND THEN USE THE MATRIX BELOW TO DETERMINE HOW TO CYCLE EACH COMPONENT. BX CLEAN STRIP CIRCUITS What It Means Cycle has been interrupted by pressing the START/RESET keypad. Light will quit flashing after the dishwasher automatically drains out the water. Unit has no water. Check the water supply. If water is turned on call for service. GY FLASHING DISPLAY LIGHTS Status Indicator Lights START/RESET WX 165D6290G033
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Modify, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Create Date : 2004:06:14 16:47:35 Producer : Acrobat Distiller 4.05 for Macintosh Subject : 913_07 165D7996P001 Creator : Adobe PageMaker 7.0 Title : 913_07 165D7996P001 Author : Debbie's G4 Modify Date : 2004:06:14 16:47:46-04:00 Page Count : 2EXIF Metadata provided by EXIF.tools