OMNIKEY HF Multi ISO RFID Reader User Manual V1.2
UserManual_HF_Multi_ISO_RFID_Reader_V1.2
UserManual_HF_Multi_ISO_RFID_Reader%20V1.2
User Manual: Pdf
Open the PDF directly: View PDF 
.
Page Count: 125
| Download | |
| Open PDF In Browser | View PDF |
TAGnology RFID GmbH | Grazer Vorstadt 142 | 8570 Voitsberg | AUSTRIA phone: +43 (0)3142/ 28 9 28-10 | fax: +43 (0)3142/ 28 9 28-20 | office@tagnology.com | www.tagnology.com Multi-ISO (OK 5553) RFID Reader USER MANUAL © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 Firmware Version 1.2 November 4, 2008 Doc Number: 1508-USM-00, Rev A.0 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Warning - Read before start-up! • The product may only be used for the intended purpose designed by the manufacturer. The operation manual should be conveniently kept available at all times for each user. • Unauthorized changes that have not been sold or recommended by the manufacturer may have a negative influence on the system the program has been installed or copied on. Such unauthorized measures shall exclude any liability by the manufacturer. • The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors, or omissions in the manual or automatically set parameters for a device or for an incorrect application of a device. • Only qualified personnel should carry out installation, operation, and maintenance procedures. • Use of the program and its installation must be in accordance with national legal requirements. • When working on devices the valid safety regulations must be observed. • International copyrights are applicable to this program. Unauthorized copying, distribution or resale of this program or of parts of this program is a violation of applicable laws and will be prosecuted. Page 2 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Read Me First About This Guide This manual describes the HF Multi ISO Reader. Its goal is to describe the reader, how it works, how to integrate it and how to use it. Contacts Europe, Middle East and Africa HID Global Corporation, Ltd. (Haverhill, UK) email: eusupport@hidglobal.com main: +44 (0) 1440 714 850 support: +44 (0) 1440 711 822 fax: +44 (0) 1440 714 840 November 4, 2008 Page 3 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Contents Warning - Read before start-up! ...................................................................................................2 Read Me First ................................................................................................................................3 About This Guide................................................................................................................. 3 Contacts ..............................................................................................................................3 Scope ................................................................................................................................8 Extended Documentation ..............................................................................................................8 Overview ................................................................................................................................9 Definitions............................................................................................................................9 Abbreviations.......................................................................................................................9 Supported tags ..................................................................................................................10 1 The MIFARE® Transponder Family ...............................................................................13 1.1 MIFARE® Standard .............................................................................................13 1.2 MIFARE® Ultralight..............................................................................................15 1.3 MIFARE® 4k ........................................................................................................15 1.4 MIFARE® ProX ....................................................................................................15 1.5 MIFARE® DESFire...............................................................................................16 1.6 my-d™ IC (SLE 55Rxx)........................................................................................19 2 ISO 14443 Type B ............................................................................................................20 2.1 SR176 ..................................................................................................................20 2.2 SRIX4K.................................................................................................................21 3 ISO 15693 .........................................................................................................................22 3.1 Coding of UID.......................................................................................................22 3.2 Memory organization............................................................................................23 3.3 my-d™ IC (SRF55VxxP) ......................................................................................23 3.4 EM 4135 ...............................................................................................................24 4 ICODE 4.1 4.2 4.3 4.4 4.5 5 ICODE EPC.......................................................................................................................27 5.1 Memory organization............................................................................................27 5.2 Serial number .......................................................................................................27 5.3 Read Block ...........................................................................................................27 ..............................................................................................................................25 Memory organization............................................................................................25 Serial number .......................................................................................................25 Write access condition .........................................................................................25 Special function (EAS,) AFI..................................................................................25 User data..............................................................................................................26 Page 4 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 5.4 Write Block ...........................................................................................................27 6 ICODE UID........................................................................................................................28 6.1 Memory organization............................................................................................28 7 Hardware ..........................................................................................................................29 7.1 Dimensions...........................................................................................................30 8 Software ...........................................................................................................................37 8.1 ASCII Protocol......................................................................................................37 8.2 Binary Protocol .....................................................................................................37 8.3 Register Set..........................................................................................................39 9 Frequently Asked Questions .......................................................................................102 References ............................................................................................................................104 Appendix A - SAM ......................................................................................................................104 Appendix B ............................................................................................................................105 Compact Serial Plug & Play Module (RDHC-020xN0-02) ..............................................105 Short Range Plug & Play Module (RDHS-0204N0-02)...................................................113 Short Range USB Desktop Reader (RDHS-0204D0-02)................................................118 Plug-In Reader (RDHP-0206P0-02)................................................................................119 Appendix C - Timings ................................................................................................................120 Appendix D - Version History....................................................................................................122 Appendix E - Approvals / Certificates ......................................................................................123 CE Declaration ................................................................................................................123 FCC Declaration..............................................................................................................124 RoHS Compliance...........................................................................................................125 List of Figures Figure 1 MIFARE® Standard: sector diagram ............................................................................................. 13 Figure 2 MIFARE® Standard: sector 0 / block 0.......................................................................................... 13 Figure 3 MIFARE® Standard: block 3, 7, 11, 15, … .................................................................................... 13 Figure 4 State diagram................................................................................................................................ 14 Figure 5 DESFire Memory........................................................................................................................... 16 Figure 7 DESFire state diagram.................................................................................................................. 17 Figure 7 Time slot formula........................................................................................................................... 55 Figure 8 Time slotted answers diagram ...................................................................................................... 55 November 4, 2008 Page 5 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Figure 9 Pin out of jumper 3 ...................................................................................................................... 108 Figure 10 Pin out of jumper 3 in RS232 Configuration ............................................................................. 109 Figure 11 Pin out of jumper 3 in RS422 Configuration ............................................................................. 110 Figure 12 Pin out of jumper 3 in RS232 Configuration ............................................................................. 111 Figure 13 Pin out of Jumper 4 (top view) .................................................................................................. 111 Figure 14 Pin out of jumper 4 .................................................................................................................... 112 Figure 15 Short Range Plug & Play Module - Top view............................................................................ 114 Figure 16 Short Range Plug & Play Module - Front View......................................................................... 115 Figure 17 Short Range Plug & Play Module - Bottom View...................................................................... 116 Figure 18 Pin out of Jumper 5 - Top View................................................................................................. 117 List of Tables Table 1 MIFARE® 4k sector index table ...................................................................................................... 15 Table 2 Electrical characteristics of pins ..................................................................................................... 33 Table 3 ASCII protocol frame ...................................................................................................................... 37 Table 4 Binary Frame Version 1.................................................................................................................. 37 Table 5 Binary Frame Version 2.................................................................................................................. 37 Table 6 Protocol configuration register ....................................................................................................... 40 Table 7 ISO 14443 A Extended Serial number of part 3 selection ............................................................. 42 Table 8 ISO 14443 A Extended Serial number of part 4 selection ............................................................. 42 Table 9 ISO 14443 A tag type ..................................................................................................................... 42 Table 10 ISO 14443 B Extended Serial number of part 3 selection ........................................................... 42 Table 11 ISO 14443 B Extended Serial number of part 4 selection ........................................................... 42 Table 12 Baud rate register......................................................................................................................... 43 Table 13 Baud rate settings ........................................................................................................................ 43 Table 14 Exact baud rates .......................................................................................................................... 43 Table 15 Communication settings............................................................................................................... 44 Table 16 Operation mode register .............................................................................................................. 44 Table 17 Protocol configuration register ..................................................................................................... 47 Table 18 Protocol configuration register ..................................................................................................... 47 Table 19 Command overview...................................................................................................................... 48 Table 20 Error codes................................................................................................................................... 50 Table 21 High Speed................................................................................................................................... 58 Table 22 Frame Size ................................................................................................................................... 58 Page 6 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Table 23 Baud Rate values ......................................................................................................................... 59 Table 24 Frame Size ................................................................................................................................... 59 Table 25 Flag Type with corresponding flag ............................................................................................... 66 Table 26 Register Type with corresponding register .................................................................................. 67 Table 27 Read USER port return values..................................................................................................... 70 Table 28 Write User port settings................................................................................................................ 71 Table 29 Sending Serial Data Frame.......................................................................................................... 71 Table 30 Receiving Serial Data Frame ....................................................................................................... 72 Table 31 Using a MIFARE® card............................................................................................................... 103 Table 32 Get a serial number from NFC ................................................................................................... 103 Table 33 Pin out of jumper 2 ..................................................................................................................... 108 Table 34 Pin out of jumper 5 ..................................................................................................................... 117 Table 35 Electrical characteristics of pins ................................................................................................. 117 Table 36 Timings....................................................................................................................................... 120 November 4, 2008 Page 7 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Scope The HID HF Multi ISO Reader Module supports a broad range of tags compliant with ISO 14443 type A and B standards, including SR176 tags, tags which belong to the Philips MIFARE® family, ISO 15693 tags, ISO 18000-3, EPC and UID tags. An open command structure allows the device to communicate with tags that use an operating system. The read/write unit supports ISO 14443-4 layer with automatic chaining, 256 byte buffer and frame length, extended time framing and up to 848kBaud transmission rates over the air interface. Additionally this unit implements a DES cipher which enables to use MIFARE® DESFire tags. These tags are designed for use in high security algorithms. A SAM interface is also available. Major applications are: • Access control, identification using high security cards • Ticketing using standard MIFARE® cards • Data storage • Multi-applications using operating systems Extended Documentation Please note that all confidential material is excluded from this documentation. You can obtain the extended documentation containing the confidential information after signing a NDA. Page 8 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Overview Definitions Anti-collision loop An algorithm used to identify and handle a dialogue between a reader and one or more tags in its antenna field. Hex notation A hexadecimal value is marked with the suffix ‘h’, i.e. A1h has the value A1 hexadecimal. ASCII notation ASCII characters are listed within apostrophes, i.e. ‘x’ means a single x. Abbreviations Abbreviation Description AID Application ID ASCII American Standard Code for Information Interchange ATR Answer to Reset ATS Answer to Select AFI Application Family Identifier block For the MIFARE® Standard one block contains 16 bytes CBC Cipher Block Chaining CID Card Identifier (logical card address, ISO 14443-4) CRC Cyclic Redundancy Check DES Data Encryption Standard, for more details about DES refer to [3]. DSFID Data storage format identifier EDC Error Detection Code EGT Extra Guard Time EOF End of Frame ETU Elementary time unit Hex / xxh Value in Hexadecimal notation I-block Information block KTT Key Transfer Transponder LSB Least Significant Bit or Byte MSB Most Significant Bit or Byte NAD Node Address (ISO 14443-4) OSI Open System Interconnection OTP One time programmable PCB Protocol Control Byte (ISO 14443-4) PCON Protocol Configuration byte of the reader PPS Protocol and Parameter Selection November 4, 2008 Page 9 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Abbreviation Description RATS Request for Answer to Select R-block Receive ready block REQA Request ISO Type A REQB Request ISO Type B RFU Reserved for Future Use S-block Supervisory block Sector For the MIFARE® Standard one sector contains 4 blocks SID Station ID SFGT Guard time after RATS SN Serial Number of a tag (a 32 bit number) SOF Start of frame TDES Triple DES Value block 32 bit data block format. Used in ticketing applicationCarriage return (0Dh) Line feed (0Ah) Transfer command Serial number Manufacturer Tag Read/Write operation Supported tags Comments ISO 14443 A MIFARE® Standard NXP √ √ √ NXP √ √ √ MIFARE Ultralight NXP √ √ √ MIFARE® ProX NXP √ √ √ MIFARE DESFire NXP √ - √ MIFARE® Mini NXP √ √ √ SLE66CLX320P Infineon √ - √ encryption not included SLE 55R04 / 08 Infineon √ - √ encryption included Smart MX NXP √ - √ Jewel Innovision √ √ √ Topaz Innovision √ √ √ MIFARE ® 4k ® ® Page 10 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 Transfer command Serial number Manufacturer Tag Read/Write operation User Manual, Firmware V1.2 Comments ISO 14443 B SLE6666CL160S Infineon √ - √ SR176 STM √ √ √ SLIX 4K STM √ √ √ ASK GTML2 ISO ASK √ - √ ASK GTML ASK √ - √ Sharp B Sharp √ - √ TOSMART P0032/64 Toshiba √ - √ ISO 14443 A compliant 1 various √ - √ 2 various √ - √ EM 4135 EM √ √ √ ICode® SLI NXP √ √ √ LRI12 STM √ √ √ LRI64 STM √ √ √ LRI128 STM √ √ √ LRI2k STM √ √ √ SRF55VxxP Infineon √ √ √ SRF55VxxS Infineon √ √ √ Tag-it™ HF-I Std TI √ √ √ Tag-it™ HF-I Pro TI - - √ only in addressed mode TempSense KSW √ - √ Temperature logging extended setup needed Dual Interface ISO 14443 B compliant ISO 15693 with 10% modulation index better performance with 10% modulation index encryption included ICode 1 Performance varies 2 Performance varies November 4, 2008 Page 11 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader Transfer command Read/Write operation Tag Serial number Manufacturer User Manual, Firmware V1.2 ICode® NXP √ √ √ ICode® EPC NXP √ √ √ ICode® UID NXP √ √ √ Comments Page 12 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 1 The MIFARE® Transponder Family The MIFARE® transponder family consists of various 13.56 MHz transponder ICs, all compliant to the ISO 14443 standard. 1.1 MIFARE® Standard The MIFARE® Standard card consists of 16 sectors. A sector includes four blocks of 16 bytes each. MIFARE® Standard Sector 2 Sector 0 (Block: 0...3) Block 8: Data or value (16 bytes) Sector 1 (Block: 4...7) Block 9: Data or value (16 bytes) Sector 2 (Block 8...11) Block 10: Data or value (16 bytes) ... Block 11: Access Conditions (4 bytes), Key A, Key B (16 bytes) Sector 15 (Block 60...63) Figure 1 MIFARE® Standard: sector diagram 1.1.1 Sector 0 / Block 0 Block 0 is read only. Serial Number (4 bytes) Check byte (1 byte) Manufacturer data (11 bytes) Figure 2 MIFARE® Standard: sector 0 / block 0 1.1.2 Blocks 3, 7, 11, 15, … Transport keys are set on delivery: Key A (6 bytes) Access Conditions (4 bytes) Key B (6 bytes) ® Figure 3 MIFARE Standard: block 3, 7, 11, 15, … Key A A0 A1 A2 A3 A4 A5 (Infineon) or FF FF FF FF FF FF (new Philips cards) Key B B0 B1 B2 B3 B4 B5 (Infineon) or FF FF FF FF FF FF (new Philips cards) Access Conditions FF 07 80 xx (key A is used to read or write; key A itself is not readable; key B is data only). For further information refer to the MIFARE® card manual. Remarks Enabled keys are always read as 00 00 00 00 00 00 Using key B as a data area will cause a security gap, due to the fact that it is necessary to rewrite key A and the access conditions at each write process. It is not recommended to use key B as a November 4, 2008 Page 13 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 data storage area. All MIFARE® cards use the following state diagram. Power Off Reset Reader Instruction Set Idle Select REQA Ready Select Log In Active read/write/... ISO 14443 Commands Halt Wake Up Halt Anticollision Loop Authenticate Authenticated Tag interfacing commands Figure 4 State diagram Page 14 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 1.2 MIFARE® Ultralight MIFARE® Ultralight cards have no encryption included. They only support plain text data transmission. MIFARE® Ultralight only supports 4 bytes per sector, but the command set uses 16 bytes per sector. Only the 4 least significant bytes are valid when using MIFARE® Ultralight. Ensure that the other bytes match with the tag content when using the write command; otherwise the read back will fail. 1.3 MIFARE® 4k MIFARE® 4k cards have an increased memory. Beginning from sector 32 (20h), sectors have 16 blocks. Due to compatibility reasons, the sector indices have changed according to the following table. The login sector has to be used to access the corresponding sector on the card. Sector 1.4 Table 1 MIFARE® 4k sector index table Block Login sector 00h 00h – 03h 00h 01h 04h – 07h 01h … … … 1Fh 7Ch – 7Fh 1Fh 20h 80h – 8Fh 20h 21h 90h – 9Fh 24h 22h A0h – AFh 28h 23h B0h – BFh 2Ch 24h C0h – CFh 30h 25h D0h – DFh 34h 26h E0h – EFh 38h 27h F0h – FFh 3Ch MIFARE® ProX MIFARE® ProX tags have an operating system onboard. Data organization depends on the operating system installed on the card. These cards can include additional functionalities such as DES or a proprietary encipher algorithm. Before accessing the operating system, the card must be selected. Customized commands are issued using the transfer command. November 4, 2008 Page 15 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 1.5 MIFARE® DESFire This tag supports additional security algorithms (DES, Triple-DES, MAC) for security sensitive applications. 1.5.1 Memory organization The memory of a DESFire card can be personalized to specific requirements. The card can be seen as data storage device like a hard disk in a PC. The memory is divided into a maximum of 28 different applications (directories) with 16 files each. An application has up to 14 keys. Depending on keys and access conditions a file can be accessed in four different ways. Plain data is never secured. Data is secured using a MAC, single DES or triple DES enciphers. The following figure describes the memory organization of a DESFire card. DESFire card (Application 0) Application 1 File ID 1 File ID 2 ... File ID n ... File ID n ... File ID n Application 2 File ID 1 File ID 2 ... Application n File ID 1 File ID 2 Figure 5 DESFire Memory Page 16 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Activate DESFire card Select Application Login to Application Select File with ID Change File Commit / Abort Transaction Figure 6 DESFire state diagram November 4, 2008 Page 17 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 1.5.1.1 Activate PICC Before accessing a DESFire card, the card must be selected. A DESFire card has a 7 byte UID. After activation, the card is powered up and ready to accept a DESFire command. Application 0 is selected automatically. 1.5.1.2 Select application To jump into another application, the application has to be selected. An application can be seen as a directory, which contains up to 16 files. The size of the application depends on the stored files. 1.5.1.3 Login to application Specific access rights can be set for each application. Login to an application allows changing the organization of the application. Login to a file opens a secured file for access. A file can be accessed in four different ways: without any security or secured with MAC, single DES or triple DES. 1.5.1.4 Select file Before accessing a file, the file must be selected 1.5.1.5 Change file A selected file can be changed according its access rights. If a file is secured, a login is required before changes can be made. 1.5.1.6 Commit / Abort transaction Value files, backup files, linear record files and cyclic record files only adapt their values after the commit transaction command is given. Several files can be changed within an application at the same time. The abort transactions command annuls all changes within an application. Power loss will cancel all modifications too. For more details about application settings and access rights refer to [2]. Page 18 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 1.6 my-d™ IC (SLE 55Rxx) my-d™ ICs are specific ICs from Infineon. These labels show a different memory organization. Two different modes of tags are supported: plain and secure mode. Memory Size of SLE Rxx-family Type User Memory Administration Memory Number of pages SLE 55R01 128 Bytes 32 Bytes 16 SLE 55R02 256 Bytes 64 Bytes 32 SLE 55R04 616 Bytes 154 Bytes 77 SLE 55R08 1024 Bytes 256 Bytes 128 SLE 55R16 2048 Bytes 512 Bytes 256 Address Byte number within a page 0 1 FFh User data … … 7Fh User data … … 4Ch User data … … 1Fh User data … … 0Fh User data … … 04h User data 2 3 4 5 6 7 November 4, 2008 SLE 55R16 Serial number (UID) SLE 55R08 00h SLE 55R04 01h SLE 55R02 02h SLE 55R01 03h Page 19 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 2 ISO 14443 Type B ISO 14443 type B cards are supported. 2.1 SR176 The SR176 label contains only 30 bytes of data organized in two bytes per page. 2.1.1 Memory organization Block address Byte 1 Byte 0 0Fh Lock byte RFU 0Eh User data … … 04h User data 03h Serial number 02h Serial number 01h Serial number 00h Serial number 2.1.2 Chip ID Serial number UID The UID is stored in the first 4 pages. Page 00h contains the LSB of the UID. Page 03h Byte 1h Page 02h Byte 0 Byte 1 Page 01h Byte 0 Byte 1 Page 00h Byte 0 Page 20 of 125 Byte 1 Byte 0 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 2.1.3 Lock byte The lock byte defines the write access condition of a pair of pages. Each bit can only be set once. This procedure is irreversible. This byte is implemented as an OTP. 2.1.4 Bit 0 Page 00h Page 01h Bit 1 Page 02h Page 03h Bit 2 Page 04h Page 05h Bit 3 Page 06h Page 07h Page 0Ah Page 0Bh Bit 4 Page 08h Page 09h Bit 5 Page 0Ch Page 0Dh Bit 6 Page 0Eh Page 0Fh Bit 7 Chip ID The Chip ID is defined in the low nibble of page 0Fh. It is manufacturer set and is used internally to select and separate single tags. 2.2 SRIX4K The SRIX4K label contains 512 bytes of data organized into four-byte pages. 2.2.1 Memory organization Block address Byte 3 Byte 2 Byte 1 Byte 0 FFh OTP Lock Reg ST Reserved ST Reserved Fixed Chip ID 7Fh User data … … 07h User data 06h 32 bits binary counter 05h 32 bits binary counter 04h 32 bits Boolean Area 03h 32 bits Boolean Area 02h 32 bits Boolean Area 01h 32 bits Boolean Area 00h 32 bits Boolean Area 2.2.2 Lock block Locking of blocks is not supported with this tag. November 4, 2008 Page 21 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 3 ISO 15693 The reader can communicate with ISO15693 tags. An anti-collision is needed if multiple instances of tags are in the same antenna field. The reader detects each type of ISO15693 labels and handles them individually 3.1 Coding of UID The UID of a tag is defined in ISO/IEC 15693-3. All tags compliant to ISO15693 support the specified format. The UID is factory programmed and cannot be changed. The UID is needed for the anti-collision sequence to separate several tags in the same antenna field. Byte 7 6 5 4 E0h MFR Code Serial number 3 2 1 0 The MFR Code is listed in ISO/IEC 7816-6:1996/Amd.1: 2000(E). Following manufacturer are tested with our reader. MFR-Code Company 02h ST Microelectronics 04h Philips Semiconductors 05h Infineon Technologies AG 07h Texas Instrument 16h EM Microelectronic-Marin SA Page 22 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 3.2 Memory organization An ISO15693 tag is separated into two blocks. An administrative block which contains the UID, AFI, DSFID and the lock page state. The user block is free for custom use. The chip manufacturer defines the amount of bytes and number of pages of each tag. As default four bytes are used for several tags. Page address Byte 3Fh User data … … 00h User data 0 1 2 3 Administrative block 3.3 my-d™ IC (SRF55VxxP) my-d™ ICs are specific ICs from Infineon. These labels show a different memory organization. Two different modes of tags are supported: plain and secure mode. Two different cards with 320 bytes or 1k bytes EEPROM memory are available. The EEPROM memory is divided into pages. Each tag is split into two parts: The administrative blocks (00h, 01h, 02h) and the user area. Administrative pages are read only and cannot be changed. User data is free for use. Additionally user data pages can be locked. This procedure is irreversible. The EEPROM of SRF55V10P is organized in 128 pages addressed 00h to 7Fh. The EEPROM of SRF55V02P consists of 32 pages addressed 00h to 1Fh. Byte number within a page 1 7Fh User data … … 1Fh User data … … 03h User data 2 3 4 5 6 02h 01h 00h 3.3.1 Serial number (UID) 7 SRF55V10P 0 SRF55V02P Address UID The UID of SRF55Vxx labels starts with 60h or E0h. November 4, 2008 Page 23 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 3.3.2 Security Bit Bit 45 of the UID defines the secure mode of the SRF55Vxx. If set, the tag supports security algorithm. Bit 45 Description 1 Tag supports crypto security mechanism 0 Chip supports plain mode only 3.4 EM 4135 The EM4135 is an ISO15693 compliant label of EM Microelectronic-Marin SA. It has eight bytes per page as the same as the my-d™ label. It only supports 36 pages. The administrative area holds the information of the access condition and the UID. Address Page 0 23h User data … … 00h User data 1 2 3 4 5 6 7 Administrative area Page 24 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 4 ICODE ICODE® IC data is stored in a non-volatile EEPROM. Its capacity is 512 bits organized in 16 blocks consisting 4 bytes each (1 block = 32 bits). First 3 blocks contain administrative data. 4.1 Memory organization Page address Byte 0Fh User data … … 05h User data 04h Family code identifier / User data 03h Special function (EAS) / User data 02h Write access condition 01h Serial number 00h Serial number 4.2 0 1 2 3 Serial number The serial number of a label is defined at the manufacturer process. It is stored on page 00h and page 01h. LSB is stored first. 4.3 Write access condition Page 02h contains the write access condition for each page. Each page can be set to read only (bits are set to 0). This procedure is irreversible. Locking page 2 no further changed of the access condition can be done. Always two bits must be change at the same time. This register is implemented as OTP. Byte 0 Byte 1 MSB LSB Byte 2 MSB LSB Byte 3 MSB LSB MSB LSB 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4.4 C User data D … E … F … 8 … 9 … A … B … 4 … 5 … 6 … 7 User data 0 Serial number 1 Serial number 2 Write access Special function 3 Special function (EAS,) AFI Special Functions (EAS) and Family Code/Application Identifier are additional features. For more information refer to the ICODE® manual. November 4, 2008 Page 25 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 4.5 User data All other blocks are free for use and can be changed according the state of the write access conditions. Page 26 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 5 ICODE EPC ICODE EPC labels data is stored in a OTP memory. Its capacity is 136 bits organized in 17 blocks consisting of 1 bytes each. All MSB of the different fields (EPC, CRC16, Destroy Code) are located at the lowest block address. 5.1 Memory organization Page address 5.2 Byte 14h – 16h Destroy Code 12h – 13h CRC 16 00h – 11h EPC Serial number The serial number of a label is defined within the EPC blocks. 5.3 Read Block It is not possible to read a block with the read block 'rb' command. 5.4 Write Block It is possible to write the EPC data (12 bytes) with the write block 'wb' command using block address 00h. November 4, 2008 Page 27 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 6 ICODE UID The memory has a capacity of 192 bits and is organized in 24 blocks, consisting of 1 byte each. All MSB of the different fields (UD, UD CRC, CRC16, Destroy Code) are located at the lowest block address. 6.1 Memory organization Page address Access Condition Description 21h – 23h OTP Destroy Code 19h - 20h OTP CRC16 14h – 18h RO UID 12h – 13h R/W UD CRC16 00h – 11h R/W User data (UD) 6.1.1 Read Block It is possible to read the user data (12 bytes) with the read block 'rb' command using block address 00h. 6.1.2 Write Block It is possible to write the UD data (12 bytes) with the write block 'wb' command using block address 00h. Additionally it is possible to write the destroy code (3 bytes) with the write block 'wb' command using block address 01h. Page 28 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 7 Hardware November 4, 2008 Page 29 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 7.1 Dimensions All dimensions listed in mm 30,48 mm 29,21 mm 1,27 mm J1 1 20 10 11 J2 25,40 mm 1,27 mm 2,54 mm Top View Page 30 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 7.1.1 Pin out – Jumper 1 PIN PIN No. Description ARX 1 Antenna RX ATX1 2 Antenna TX1 VDD 3 Supply Voltage GND 4 Ground ATX2 5 Antenna TX2 TGND 6 Antenna Ground SAM CLK 7 SAM clock SAM IO 8 SAM IO SAM RESET 9 SAM Reset RTS 10 Request to Send November 4, 2008 Page 31 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 7.1.2 Electrical characteristics of J1 PINs PIN PIN No. Min ARX 1 1.1V ATX1 2 VDD 3 Typ. Max. Description 4.4V Antenna RX Antenna TX1 34 VPP 13.56MHz 100 mAPP 50VPP +4.5V +5.0V +5.5V Supply Voltage 32mA 150mA 250mA Supply Current (without SAM) 13,56 MHz GND 4 GND ATX2 5 13,56 MHz 34 VPP Ground 13.56MHz 100 mAPP 50VPP Antenna TX2 TGND 6 GND Antenna Ground SAM CLK 7 TTL SAM clock 25mA 3,39MHz SAM IO 8 TTL 25 mA IO for SAM Input and SAM Output SAM RESET 9 TTL 25 mA SAM Reset RTS 10 TTL 25 mA Request to Send Page 32 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 7.1.3 Pin out – Jumper 2 PIN PIN No. Description VDD 20 Supply Voltage GND 19 Ground LEDg 18 LED green (reading LED) LEDr 17 LED red EN 16 Enable reader, open or logic high MCLR 15 Master clear USER 14 User Port DIR 13 Direction of RS 485 TX 12 TX to PC RX 11 RX from PC 7.1.4 Electrical characteristics of J2 PINs Table 2 Electrical characteristics of pins Min Typ. Max. Description PIN PIN No. RX 11 USART-TTL 1 25 mA RX to PC To RS232, RS485 or RS422 device driver TX 12 USART-TTL1 25 mA TX to PC To RS232, RS485 or RS422 device driver DIR 13 TTL 25 mA Direction of RS 485 Logic High = Reader to Host Logic Low = Host to Reader USER 14 TTL 3 25 mA User Port MCLR 15 TTL 4 EN 16 ST 5 Master clear Leave unconnected. Low will reset the register and the key management to default values. 25 mA 1 Universal Synchronous Asynchronous Receiver Transmitter 3 TTL buffer output / input Enable reader logic low will disable the reader Open or logic high 4 Voltage spikes below GND at the MCLR/VDD pin, including currents greater than 80mA, may cause latch-up. Thus, a series resistor of 50-100Ω should be used when applying a "low" level to the MCLR/VDD, rather than pulling this pin directly to GND. 5 Schmitt trigger buffer input November 4, 2008 Page 33 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 PIN PIN No. Min Typ. Max. Description LEDr 17 VDDmin @ 25mA VDDtyp @ 11mA VDDmax @ 0 mA LED red Output Voltage 11mA 25mA External Resistor min. 200 Ω 1.4V @ 11mA VDD @ 0mA LED green (reading LED) with 330 Ω (internal serial) resistor 11mA 15mA LEDg 18 GND 19 VDD 20 IDD 7.1.5 GND Ground +4.5V +5.0V +5.5V Supply Voltage 32 mA 150 mA 250 mA Supply Current (Without SAM) External Connections 7.1.5.1 Power Supply If the supply voltage and any noise modulated on the supply voltage remains within the specified limits, no further filtering is required. In some cases it is recommended to use additional filtering for the power supply line. Insufficient power line filtering could cause unexpected or irregular performance drops. Option 1 +5V DC OEM Board 20 19 uC Option 2 +5V DC OEM Board 3 4 Page 34 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 The board can be connected as shown above. Both alternatives are possible and can be used as they fit best into the layout of the carrier board. The two VCC PINs and the two GND PINs are connected internally. 7.1.5.2 Antenna The typical antenna tuning and matching network is shown below. The external antenna has to have the right inductance and a certain resistor and capacitor combination for an optimized frequency tuning and antenna matching. R1 C1 L ANT C3 C5 C4 1 2 OEM Board 5 6 C2 More details about the antenna design are available in the HIDid antenna design guide manual. This document can be downloaded from http://www.hidcorp.com/Omnikey. Please refer also to the specific application notes for the Philips reader IC (MIFARE® & I-Code, Micore Reader IC family Directly Matched Antenna Design). 7.1.5.3 Serial Interface The OEM Board can be connected directly with a micro controller. Alternatively the OEM Board also can be connected to most serial interface types by using the right interface converter circuit. In order to optimize the communication quality the specific application note of the interface converter circuit needs to be taken into consideration. OEM Board 12 11 Interface Converter Circuit Host Interface November 4, 2008 Page 35 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 7.1.5.4 Function Control LEDs Two external LEDs can be connected to the OEM Board. There are two alternatives possible. Option 1 OEM Board 330 Ohm uC 18 17 Option 2 OEM Board 330 Ohm uC 18 17 330 Ohm In both cases the LED supply voltage levels are TTL levels. Page 36 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8 Software By default, data is transmitted at 9600, n, 8, 1, no handshaking. Two protocol modes are supported. The protocol mode is configured in the reader EEPROM. As factory default, the ASCII protocol is used. 8.1 ASCII Protocol This protocol is designed for easy handling. The commands are issued using a terminal program. Data is transmitted as ASCII hexadecimal that can be displayed on any terminal program (i.e. HyperTerminal). Table 3 ASCII protocol frame Command Data Variable length Variable length 8.2 Binary Protocol This protocol is designed for industrial applications with synchronization and frame checking. An addressing byte for party line (master/slave, multi-drop) is also included. The protocol usually requires a device driver. Data is transmitted in binary mode. The reader uses an internal binary watchdog timer to ensure correct framing. STX Station ID Table 4 Binary Frame Version 1 Length Data 1 byte 1 byte 1 byte Variable length BCC ETX 1 byte 1 byte The binary frame version 2 is only sent to the host. It is implemented to give extended information to the host. Version 2 must be enabled in the Protocol configuration 2 register. STX Station ID Table 5 Binary Frame Version 2 Length Flags Data 1 byte 1 byte 1 byte 8.2.1 1 byte Variable length BCC ETX 1 byte 1 byte STX Start of transmission (02h) 8.2.2 Station ID Unique ID of the station 8.2.3 00h: Reserved for the bus master. Readers send response to this device ID. FFh: Broadcast message. All devices will execute the command and send their response. Length Length defines the length of the data block, including the flag byte, if binary protocol version 2 is activated. If length is set to zero, 256 data bytes are transmitted. The reader module only can send 256 data bytes, but cannot receive commands with 256 bytes. November 4, 2008 Page 37 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.2.4 Flags The flag byte gives additional information to the host. Bit 3 – Bit 7 Bit 1 – Bit 2 Bit 0 RFU Leading Character Info Error State Error State If cleared, the command was processed successfully. If Error State is set, an error occurred. Leading Character Info Bit 1 & 2 defines how to interpret the data in the binary frame. Bit 2 Bit 1 Description 0 0 No leading character available, all values are hexadecimal. 0 1 The data contains one leading character. 1 0 All data bytes are characters. 1 1 RFU 8.2.5 Data This part contains the command and the data. The command values are the same as in ASCII protocol mode (‘x’, ‘s’, …) whereas data is transmitted in binary mode. The length of the command block depends on the instruction. 8.2.6 Block Check Character (BCC) The BCC is used to detect transmission errors. The BCC is calculated XOR-ing each byte of the transmission frame excluding the STX/BCC and ETX characters. The flags are part of the data. BCC = ( StatID) XOR ( Length) XOR (Command / Data 0 ) XOR ... XOR (Command / Data N ) 8.2.7 ETX End of transmission. (03h) Page 38 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.2.8 Remarks If the reader device receives an invalid instruction frame (i.e. wrong BCC) or the requested station ID does not match the internal ID of the reader, the command is not executed. The reader waits for the next valid frame. The automatic binary time-out (see protocol configuration register) is used to detect incomplete binary frames. 8.2.9 Examples 02h 64h 01h 78h 1Dh 03h STX Station ID Length ‘x’ BCC ETX This instruction frame will reset the reader module with the station ID 64h. 8.3 Register Set The reader has several system flags used for customization purposes. The flags are stored in its non-volatile EEPROM. The reader accepts changes to these settings only during the start-up phase. Clearing all RFU bits is recommended in order to guarantee compatibility with future releases. The reader can store up to 32 authentication keys internally to login standard MIFARE® cards. An additional 32 keys can be stored for DESFire authentication. All keys are read only and cannot be accessed via the interface lines. 8.3.1 EEPROM memory organization Register Description 00h … 04h Unique device ID; read only 05h … 09h Administrative data; read only 0Ah Station ID 0Bh Protocol configuration 0Ch Baud rate 0Dh Command Guard Time 0Eh Operation Mode 0Fh Single shot time-out value 10h Internal use / Do not change 11h Internal use / Do not change 12h Internal use / Do not change 13h Protocol configuration 2 14h Reset Off Time 15h Reset Recovery Time 16h Application Family Identifier 17h ISO 14443A Selection Time-out 18h ISO 14443B Selection Time-out 19h SR176 Selection Time-out November 4, 2008 Page 39 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Register Description 1Ah ISO 15693 Selection Time-out 1Bh Protocol configuration 3 1Ch Page Start 1Dh Internal use / Do not change 1Eh Internal use / Do not change 1Fh Page number 20h Protocol configuration 4 21h CID 22h Internal use / Do not change 23h Internal use / Do not change 24h Internal use / Do not change 25h Internal use / Do not change 26h - 7Fh RFU 80h … EFh User data 8.3.2 Unique device ID (00h – 04h) The unique device ID identifies a reader module. It is factory programmed and cannot be changed. 8.3.3 Station ID (0Ah) The station ID is used in binary mode to address a device in party line set up. The station ID can range from 01h to FEh and can be set freely. The value 00h is reserved for the bus master. All readers send their response to this device. The broadcast message (FFh) forces all readers to response to the command. Default value is 01h. 8.3.4 Protocol configuration (0Bh) The protocol configuration register (PCON) specifies general behavior of the reader device. Default value is 41h. Table 6 Protocol configuration register Protocol configuration register Bit 7 Bit 6 Bit 5 Extend-ed ID Extend-ed Protocol Singleshot Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 LED New serial mode Multitag Protocol Auto- start 8.3.4.1 Auto start (default 1) If set, the reader device will start up in continuous read mode automatically. This is only valid in ASCII mode. 8.3.4.2 Protocol (default 0) If Protocol is set to ‘1’, then the reader uses binary protocol mode. Refer to binary protocol for further information on the binary protocol format. Default setting = ASCII protocol (0). Page 40 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.4.3 Multitag (default 0) The Multitag flag will enable multi-tag recognition in continuous read mode. All tags are detected and displayed. Due to the more complex search algorithm, the continuous read command decreases its detection speed. 8.3.4.4 New Serial Mode (default 0) If New Serial Mode is set to ‘1’, new serial mode is enabled. A leading character is added to the serial number. Leading Character Description D ICode UID E ICode EPC I ICode J ISO 14443 A Jewel tag M ISO 14443 A S SR 176 V ISO 15693 Z ISO 14443 B 8.3.4.5 LED (default 0) If set the reader suppresses any LED activity. The user manages the state of the LEDs. 8.3.4.6 Single Shot (default 0) If Single Shot is set, the reader displays the serial number of a tag in continuous read mode once within a specified time-out. The time-out is defined at EEPROM register 0Fh. The delay time can be adjusted stepwise in 100ms steps. 00h indicates no delay and FFh indicates infinite delay. Note: The delay precision depends on reset off and reset recovery time. 8.3.4.7 Extended Protocol (default 1) If Extended Protocol is set, the transfer data telegram command supports ISO14443-4 and automatically process the WTX and chaining for smaller frames. If sending ISO 14443-3 commands this flag has to be switched off. The transfer data telegram command is only supported in normal mode, not in transmit / receive mode. November 4, 2008 Page 41 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.4.8 Extend ID (default 0) If set, the reader extends the serial number with additional information. ISO 14443 A tags Table 7 ISO 14443 A Extended Serial number of part 3 selection Tag type / ReqA Serial number [SAK] 1 byte / 2 bytes 4 / 7 / 10 bytes 1 byte Table 8 ISO 14443 A Extended Serial number of part 4 selection Tag type / ReqA Serial number [SAK] ATS Used Speed [CID] 1 byte / 2 bytes 1 byte 4 / 7 / 10 bytes 1 byte n bytes 1 byte The tag type byte indicates the type of cascade level. Table 9 ISO 14443 A tag type Tag type Description 00h Cascade level 1 transponder 01h Cascade level 2 transponder 02h Cascade level 3 transponder ISO 14443 B tags Table 10 ISO 14443 B Extended Serial number of part 3 selection Serial number Application data Protocol info MBLI/CID 4 bytes 4 bytes 3 bytes 1 byte Table 11 ISO 14443 B Extended Serial number of part 4 selection Serial number Application data Protocol info MBLI / CID Used Speed [CID] 4 bytes 4 bytes 3 bytes 1 byte 1 byte 1 byte For detailed description of Application Data, Protocol Info and MBLI/CID, refer to the ISO 14443 documentation [1]. Page 42 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.5 BAUD, Baud rate control register (0Ch) The baud rate register defines the communication speed of the reader device. Default value is 00h. Table 12 Baud rate register Baud rate register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RFU RFU RFU RFU RFU BS2 BS1 BS0 This register defines the baud rate of the device. Table 13 Baud rate settings Baud rate BS2 BS1 BS0 0 0 0 9600 baud (default) 0 0 1 19200 baud 0 1 0 38400 baud 0 1 1 57600 baud 1 0 0 115200 baud 1 0 1 230400 baud (depends on the used interface chip) 1 1 0 460800 baud (depends on the used interface chip) With the high baud rates (230400 and 460800 baud), proper operation depends on the interface chip used. Please note that some of the interface chips available do not support these high baud rates. The following table describes the exact baud rates used by the reader. Baud rate Table 14 Exact baud rates Exact baud rate Difference 9600 baud 9603 baud 0.03 % 19200 baud 19207 baud 0.04 % 38400 baud 38305 baud -0.25 % 57600 baud 57458 baud -0.25 % 115200 baud 114915 baud -0.25 % 230400 baud 233793 baud 1.47 % 460800 baud 452000 baud -1.91 % The following table describes the communication settings November 4, 2008 Page 43 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Table 15 Communication settings Description 8 data bits No parity bit 1 stop bit No flow control 8.3.5.1 CF Card Version The Baud rate of the CF Card version is limited to 115200 baud. 230400 and 460800 are not supported. 8.3.6 Command Guard Time (0Dh) The Command Guard Time is used to ensure that commands are not sent to fast consecutively. Following commands are sent after the guard time is elapsed. One time slice is around 37,8us. The longest timeout value is 9,6ms (FFh). The default value is 20h (1,2ms). 8.3.7 OPMODE, operating mode register (0Eh) The operation mode register defines which tag types the reader supports. This register enables fast tag recognition because only defined tag types are requested. Table 16 Operation mode register Operation mode register ISO 14443A Bit 0 (LSB) ISO 14443B Bit 1 SR176 Bit 2 ICODE Bit 3 ISO 15693 Bit 4 ICODE EPC Bit 5 ICODE UID RFU Bit 7 (MSB) Bit 6 Innovision Jewel tag Innovision Jewel tag is part of ISO 14443 Type A. It can not be separately switched on/off. 8.3.8 Single Shot Time-out (0Fh) The time-out value defines the delay time between two responses of the reader. It only has effect in continuous read mode. To enable the time-out, the single shot flag has to be set. See the protocol configuration register above. One time-out slice is around 100ms. Exact timing depends on the protocol used. Value 00h indicates no delay time. Default value is 0Ah (1 second). Page 44 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.9 Protocol configuration 2 (13h) The protocol configuration register 2 (PCON2) further specifies the general behavior of the reader device. Default value is 00h. Protocol configuration 2 register Bit 7 Bit 6 Bit 5 Bit 4 Disable ISO 14443 4 Error Handling Enable ISO 14443B Reset Recovery AntiTime Multiplier collision Bit 3 Bit 2 Bit 1 Bit 0 Noisy Environment Enable binary frame v2 Disable Disable startmulti-tag up message reset 8.3.9.1 Disable multi-tag reset (default 0) If set, the reader does not reset before the multi-tag list and multi-select command have been performed. 8.3.9.2 Disable start-up message (default 0) If Disable start-up message is set, the reader suppresses the start-up message in ASCII mode. This flag is ignored in binary protocol mode. 8.3.9.3 Enable binary frame v2 (default 0) If Enable binary frame v2 is set, the reader sends version 2 binary frames. The get station ID command always sends version 1 binary frames! 8.3.9.4 Noisy Environment (default 0) If Noisy Environment is set, the continuous read mode can only be aborted with the '.' character. When working in a noisy environment, the probability for a reception of an arbitrary/stochastic signal is quite high. This implies a high probability of an unintentional command execution. To reduce this probability, only one character (out of 255) is chosen (‘.’) to be interpreted as the continuous read stop command. 8.3.9.5 Reset Recovery Time Multiplier (default 0) Multiplies the Reset Recovery Time, including the recovery time of the field reset command. Reset Recovery Time Multiplier Reset Recovery Time 0 1x 1 2x 2 3x 3 4x 8.3.9.6 Enable ISO14443 B Anti-collision (default 0) If set, the anti-collision algorithm for ISO 14443 B tags is enabled. 8.3.9.7 Disable ISO 14443-4 Error Handling (default 0) If Disable ISO 14443-4 Error Handling is set, ISO14443-4 Error Handling is disabled. The error handling always uses the TMR time-out. November 4, 2008 Page 45 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.10 Reset Off Time (14h) The Reset Off Time register represents the field off time in ms. This register is used for the select, continuous read and multi-tag commands. Default value is 0Ah. 8.3.11 Reset Recovery Time (15h) The Reset Recovery Time register represents the recovery time in ms after the field is turned on. This register is used for the select, continuous read and multi-tag commands. Default value is 25h. 8.3.12 Application Family Identifier (16h) The AFI (Application Family Identifier) is only supported for ISO14443B and ISO15693 tags. If the set value is different from 00h, the AFI is used. Only transponders with an identical AFI will answer to the reader. Default value is 00h. 8.3.13 Selection Time-out ISO 14443A (17h) The Selection Time-out represents the reader card communication time-out for the select, high-speed select, continuous read, multilist, multi-select and MIFARE® login command with ISO 14443A tags. Use low values for a better reaction time between the card and the reader. One time slice is around 300us. The default value is 10h. 8.3.14 Selection Time-out ISO 14443B (18h) The Selection Time-out represents the reader card communication time-out for the select, high-speed select, continuous read, multilist and multi-select commands with ISO 14443B tags. For a better reaction time, use low values. One time slice is around 300µs. The default value is 10h. 8.3.15 Selection Time-out SR176 (19h) The Selection Time-out represents the reader card communication time-out for the select, continuous read, multilist and multi-select command with SR176 tags. For a better reaction time, use low values. One time slice is around 300µs. The default value is 10h. 8.3.16 Selection Time-out ISO 15693 (1Ah) The Selection Time-out represents the reader card communication time-out for the select, high-speed select, continuous read, multilist, multi-select and MIFARE® login command with ISO 15693 tags. Use low values for a better reaction time between the card and the reader. One time slice is around 300us. The default value is 20h. Page 46 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.17 Protocol configuration 3 (1Bh) The protocol configuration register 3 (PCON3) further specifies the general behavior of the reader device. Default value is 00h. Table 17 Protocol configuration register Protocol configuration 3 register Bit 7 Bit 6 Bit 5 SAK Extended ID ReqA Extended ID Internal use / do not change 8.3.17.1 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page Read RFU Disable automatic ISO 14443-4 timeouts Disable automatic ISO 14443-4 timeouts (default 0) If Disable automatic ISO 14443-4 timeouts is set the automatic ISO 14443-4 timeouts are disabled. The timeouts specified with TMR registers are used. 8.3.17.2 Page read (default 0) If set the continuous read mode retrieves the content of the tag instead of the serial number. The register Page Start (1Ch) defines the start block and the Page Number (1Fh) defines the number of blocks to be read. 8.3.17.3 ReqA Extended ID (default 0) If set the Extended ID information for ISO14443 A tags replaces the cascade level information (1 byte) with Request A answer (2 bytes). 8.3.17.4 SAK Extended ID (default 0) If set the Extended ID information for ISO 14443 A tags will include the SAK byte behind the serial number. 8.3.18 Protocol configuration 4 (20h) The protocol configuration register (PCON4) specifies general behavior of the reader device. Default value is 00h. Table 18 Protocol configuration register Protocol configuration register Bit 7 RFU 8.3.18.1 Bit 6 RFU Bit 5 RFU Bit 4 Bit 3 RFU Internal CID use / do Extended not change ID Bit 2 Bit 1 Bit 0 WupA/B Disable Read after Write Disable Read after Write (default 0) If set, the reader device will not make a read after write for the block write commands "w", "wb", "wd" and "wv". If the read after write is deactivated, acknowledge from the write commands is a 00h byte instead of the written data. November 4, 2008 Page 47 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.18.2 WupA/B (default 0) If set, the reader device will use WupA/B instead of ReqA/B during selection of an ISO 14443 tag. Supported commands are select, high-speed select and multi-select. 8.3.18.3 CID Extended ID (default 0) If set, the extended ID information for ISO 14443 A/B tags will be extended with the CID information only for the high-speed select. The CID byte will be appended on the end of the output. 8.3.19 CID (21h) The Card Identifier (CID) is used to activate multiple ISO 14443-4 cards at the same time. If only one tag at the same time is used this value should be left 0. Default value is 00h. 8.3.20 User data (80h - EFh) These registers are for free use. 8.3.21 Instruction Set Following table describes all the commands of the reader device. Each command returns an answer to the host. Exceptions are mentioned explicitly. The green LED acknowledges a successfully executed command. The red LED indicates an error. 8.3.22 Common Commands Overview Command Table 19 Command overview Description '!' Test continuous read / Check KTT upload status 'c' Continuous read '.' Abort continuous read, refer to continuous read 'dg' / 'dn' / 'dr' Set LED 'ds' DES encryption / decryption of data 'g' Get ID 'h' High-speed select 'k' Lock block 'm' MultiTag select / tag list 'o+a' / 'o+b' / 'o+d' / 'o+e' / 'o+i' / 'o+s' / 'o+v' Include tag type 'o-a' / 'o-b' / 'o-d' / 'o-e' / 'o-i' / 'o-s' / 'o-v' Exclude tag type 'oa' / 'ob' / 'od' / 'oe' / 'oi' / 'ot' Set tag type / 'os' / 'ov' 'of' Set configuration flags 'og' Set configuration register 'ox' Reread all register 'poff' / 'pon' Antenna power off/on Page 48 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Command Description 'pr' / 'pw' Read / write user port 'q' Quiet 'ra' Resend last answer 'r' / 'rb' Read block 'rd' Read data (multiple blocks) 'rp' Read EEPROM register 's' Select 'v' Get version 'w' / 'wb' Write block 'wd' Write data (multiple blocks) 'wp' Write EEPROM register 'x' Reset 'y' Field reset ISO 14443 Type A (MIFARE®) only commands '+' Increment value block (credit) '-' Decrement value block (debit) '=' Copy value block (backup) 'l' Login (authenticate tag) 'rv' Read value block 'wv' Write value block Key Management 'ar' Authenticate to reader 'ia' Get key access rights 'it' Get key status 'rt' Reset key table 'ua' Update key access rights 'uc' Change key type 'uk' Update key my-d™ secure commands '!' Check KTT upload status / Test continuous read '*' Abort KTT upload 'as' Authenticate to sector 'ik' Issue transponder key 'ut' Prepare for KTT 'z' my-d™ command November 4, 2008 Page 49 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.23 Error Codes Following figure shows an overview of all error messages of the reader device. Table 20 Error codes Error Code Description ‘?’ Unknown command 'C' Collision or CRC/MAC Error ‘F’ General failure ‘I’ Invalid value format, specified block does not match the value format ‘N’ No tag in the field 'O' Operation mode failure or file not selected ‘R’ Command parameter out of range 'X' Authentication failed 8.3.24 Common commands 8.3.24.1 Test Continuous Read / Check KTT Upload Status This command tests the state of the continuous read command and the state of the Prepare for KTT 'ut' command. The test continuous read command is only valid in ASCII mode. Command Command Data '!' None Answer Answer Description '!' Continuous read mode is active. 00h Keys from KTT successfully uploaded 01h Error during key upload detected, upload aborted 02h No KTT found, other tag was detected FFh Prepare for KTT is in awareness mode 'F' Continuous read and Prepare for KTT is not active. no response Key uploading is in progress Page 50 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.2 Continuous Read The reader device reads and displays serial numbers continuously while one or more tags remain in the field. This command stops if any character is sent to the reader module. The reader module returns the character ‘S’ (53h). The reader supports different tag types at the same time. To increase the reading performance switch to a single tag mode. If more than one tag of the same type should be detected at the same time, the Multitag flag must be activated. The response data length depends on the tag type. Command Command Data 'c' None Answer Answer Description Data Serial number (n bytes) 'N' Error: No Tag in the field (only binary protocol) 8.3.24.2.1 Multitag continuous read mode If the Multitag flag is set in the Protocol Configuration (PCON) register the reader reads multiple tags continuously. 8.3.24.2.2 Auto start The continuous read mode is started automatically in ASCII mode. The auto start flag must be set in the PCON register. 8.3.24.2.3 Noisy Environment If the Noisy Environment flag is set, the continuous read mode can only be aborted with the '.' character. This is only valid in ASCII mode. 8.3.24.2.4 Binary mode This command is fully supported in binary protocol mode except the test continuous read command and the noisy environment flag. Do not use this command on bus system environment in binary mode, because the continuous read mode will take possession of the bus system. November 4, 2008 Page 51 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.2.5 Simple access control applications Serial numbers are always sent plain. Data encryption is activated after a successful login. For simple access control applications the use read-only blocks for the identification of the tag is recommended. Reading any block (even the manufacturer block) of the transponder will increase your security. 8.3.24.2.6 LED activity The LED stays green as long as a tag was found and goes dark if the tag is removed from the field. 8.3.24.3 Set LED This command controls the LED activity. If the LED flag is set, the automatic LED function is switched off. The user can set the state of the LED manually. Command Command Data 'dg' None 'dr' None 'dn' None Answer Answer Description 'DG' 'DR' 'DN' String of LED state Example Command Answer Description 'dg' DG Switch on LED green, LED red off 'dr' DR Switch on LED red, LED green off 'dn' DN Switch off both LEDs Page 52 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.4 DES encryption / decryption of data This command returns 8 bytes of encrypted / decrypted data. Command Command Data 'ds' Options (1 byte) Key (8/16 bytes) / Key Number (1 byte) Data (8 byte) Answer Answer Description Data Encrypted / Decrypted data (8 bytes) Option byte Option byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 RFU RFU RFU RFU RFU Encode Key Length Key Index Bit 0 Key Index If the Key Index is set, the command only needs the key number (1 byte) instead of the key (8/16 bytes). The key number corresponds to the key number used in the key management. Key Length If the Key Length is set, the command uses the TDES algorithm with 16-byte key. If cleared, the command uses the DES algorithm with 8-byte key. If key index is used the key length flag is valid. Encode Setting this flag encodes the data. Clearing this flag decodes the data. November 4, 2008 Page 53 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.5 Get ID This command returns the station ID of the reader device. The answer is time slotted to enable the detection of all devices in party line mode. The station ID has only effect in binary mode. Command Command Data 'g' None Answer Answer Description Data Station ID of the reader device (1 byte) Page 54 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.5.1 Time slotted answer In party line mode, more than one reader can be used simultaneously. The time slotted answer allows separating in time the answers from all connected devices. The station ID is used to determine the correct time slot. The reader supports up to 254 unique time slots. The following formula calculates the duration of one time slot (only one baud rate is supported per party line): T0 [ s ] = 10 *6 Baudrate Figure 7 Time slot formula The following figure shows the timing diagram of time slotted answers. Timeslot HOST Reader (01) Reader (03) Reader (04) 0 1 T0 T1 2 3 4 5 T2 T3 T4 T5 … 252 253 254 T252 T253 T254 'g' → ← 01 ← 03 ← 04 ← 254 Reader (254) Figure 8 Time slotted answers diagram November 4, 2008 Page 55 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.5.2 Binary Protocol Version 2 This command never sends version 2 binary frames. 8.3.24.6 High-speed select This command selects a card in the antenna field (according to the selection criteria) or prepares a multi-select command, switches to high baud rates and enables 256-byte frames. If execution is successful, the command returns the UID of the selected card and the used baud rate. The reader automatically detects the maximum frame size of the card. The reader also tries to communicate to the transponder with the specified baud rate. If no communication is possible, the reader will automatically decrease the speed to the next lower value. In synchronous mode the up and downlink speed are identical. In asynchronous mode the up and downlink speed can be different. This command can also force the reader to the communication speed and frame size of the tag to the specified values. This is only needed if the high-speed select is done manually with the transfer command. Command Command Data ‘h’ Option byte (1 byte) synchronous mode 00h … select a single card with 106kBaud 02h … select a single card with 212kBaud 04h … select a single card with 424kBaud 08h … select a single card with 848kBaud 10h … prepare next multi-select for 106kbaud 12h … prepare next multi-select for 212kbaud 14h … prepare next multi-select for 424kbaud 18h … prepare next multi-select for 848kbaud 20h … forces reader to 106kBaud 22h … forces reader to 212kBaud 24h … forces reader to 424kBaud 28h … forces reader to 848kBaud tag size 30h – 38h … force tag frame size asynchronous mode 80h … select a single card with 106kBaud 82h … select a single card with 212kBaud 84h … select a single card with 424kBaud 88h … select a single card with 848kBaud 90h … prepare next multi-select for 106kbaud 92h … prepare next multi-select for 212kbaud 94h … prepare next multi-select for 424kbaud 98h … prepare next multi-select for 848kbaud Page 56 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Command Data A0h … forces reader to 106kBaud from tag to reader A2h … forces reader to 212kBaud from tag to reader A4h … forces reader to 424kBaud from tag to reader A8h … forces reader to 848kBaud from tag to reader B0h … forces reader to 106kBaud from reader to tag B2h … forces reader to 212kBaud from reader to tag B4h … forces reader to 424kBaud from reader to tag B8h … forces reader to 848kBaud from reader to tag Answer Answer Description Data (n bytes) + frame size and baud rate (1byte) Serial number + frame size used and baud rate 'F' Error: General failure ‘N’ Error: No Tag in the field Note: If the tag does not support ISO 14443 part 4 F0h will return after serial number instead of used frame size/baud rate. Examples High-speed select Command Description h08 1234567890ABCD84 Select the card with UID 1234567890SABCD. The card supports a 256-byte frame size and 424kBaud on the air interface. High-speed multi-select Command Description h18 m1234567890ABCD Prepare next multi-select for 848kBd 1234567890ABCD84 Select the card with UID 1234567890SABCD. The card supports a 256-byte frame size and 424kBaud on the air interface. November 4, 2008 Page 57 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.6.1 Answer from 0xh and 1xh The lower nibble contains the baud rate used for the air interface. Table 21 High Speed Baud Rate Description x0 106kBaud x2 212kBaud x4 424kBaud x8 848kBaud The higher nibble contains the frame size used for the air interface. Table 22 Frame Size Frame Size Description 0x 16 Bytes 1x 24 Bytes 2x 32 Bytes 3x 40 Bytes 4x 48 Bytes 5x 64 Bytes 6x 96 Bytes 7x 128 Bytes 8x 256 Bytes Page 58 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.6.2 Answer from 8xh The lower nibble contains the baud rate used for the air interface. The value for the baud rate is XORed with the used up and downlink speed. Table 23 Baud Rate values Baud Rate Description x1 106kBaud x2 212kBaud x4 424kBaud x8 848kBaud The higher nibble contains the frame size used for the air interface. Table 24 Frame Size Frame Size Description 0x 16 Bytes 1x 24 Bytes 2x 32 Bytes 3x 40 Bytes 4x 48 Bytes 5x 64 Bytes 6x 96 Bytes 7x 128 Bytes 8x 256 Bytes 8.3.24.6.3 Answer from 2xh, 3xh, 9xh, Axh and Bxh The option byte is returned as the answer. 8.3.24.6.4 Select a single tag No previous continuous read is required. The command executes an automatic field reset. 8.3.24.6.5 Extended ID See above for more information on Extended ID. The RATS answer is inserted between the serial number and baud rate / frame size byte for ISO14443 A tags. 8.3.24.6.6 Multiple tags This command with parameter 1xh prepares the next multi-select command as a highspeed select. Any other command will disable the preparation. November 4, 2008 Page 59 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.6.7 RATS Guard Time SFGT A high-speed select with parameters 0xh and 1xh automatically waits the SFGT guard time received from the tag before sending the PPS command. 8.3.24.7 Lock block This command locks a block permanently. Only SR176 and ISO 15693 tags are supported. Command Command Data 'k' Block address (1 byte) Answer Answer Description data 'K' + page address 'F' Error: Lock failure 'N' Error: No tag in field 'O' Error: Operation mode failure (only SR176 and ISO 15693 tags are supported) 'X' Error: Block already locked Example Command Description k05 K05 Lock block 05. 8.3.24.7.1 Operation mode failure 'O' The presented tag is not a SR176 or a ISO 15693 tag. 8.3.24.7.2 Apply settings After locking a block permanently, the tag needs to be selected for the settings to apply. Page 60 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.8 Multi-Tag Selection / List This command detects several tags at the same time. It replaces the fast select command ('s') in multiple tag surroundings. The Multi-Tag List command lists all tags with their serial numbers. Use the Multi-Tag Select command to select a single tag. Each tag has to be selected separately. Command Command Data 'm' Serial number (n bytes) (1 byte) Answer Answer Description Data serial number 'N' Error: No Tag in the field Example Command Description m 04E9E700000000 34030F07 02 m04E9E700000000 Select card with its serial number 8.3.24.8.1 Æ first card Æ second card Æ number of detected tags Multi-tag list Sending a as the first parameter, the reader returns a list of all tags present in the antenna field. In the end the total number of tags detected is returned. 8.3.24.8.2 Reading distance Each card needs a specific amount of power. The reader always provides the same power level. Therefore, the reading distance will decrease if more tags are present. Basically, the reading distance depends on the tag, the antenna and the tuning of the antenna. 8.3.24.8.3 Multi-tag select Using the serial number with as parameter, the corresponding tag will be selected. High-level interactions can be performed addressing only this card. All other tags remain silent. 8.3.24.8.4 Multi-tag reset The antenna field reset can be deactivated with the Protocol configuration 2 register. By suppressing the antenna field reset, it is possible to detect only new tags in the antenna field. Attention: It could be possible that ISO 15693 tags are interfered from ISO14443 type B and SR 176 tags. In this case the ISO 15693 tag will always answers on a multi list command even there had been no field reset before. In this case, deactivate ISO 14443 B and SR 176 tags. November 4, 2008 Page 61 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.8.5 Maximum number of tags The maximum number of tags in the antenna field is limited to 64 and by the physical characteristics of the antenna. 8.3.24.8.6 LED activity The LED stays green as long as a tag was found and goes dark if the command is finished. 8.3.24.9 Include tag type This command includes a specific tag type to those addressed by the reader device. Command Command Data ‘o+’ Tag type (1 byte) Answer Answer Description 'O+' + tag type (1 byte) Command code + String of tag type Tag type character Refer to Set tag type. Example Command Description o+a Include ISO14443-A to the tag types addressed by the reader device. Page 62 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.10 Exclude tag type This command excludes a specific tag type from being addressed by the reader device. Command Command Data ‘o-’ Tag type (1 byte) Answer Answer Description 'O-' + tag type (1 byte) Command code + String of tag type Tag type character Refer to Set tag type. Example Command Description o-a Exclude ISO14443-A from the tag types addressed by the reader device. November 4, 2008 Page 63 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.11 Set tag type This command sets up the reader for a specific tag type. The continuous read function will speed up because only this type of tag is addressed. After a reset, the reader starts as defined in its start-up configuration. Command Command Data 'o' ISO type (1 byte) 'a' … ISO 14443 Type A 'b' … ISO 14443 Type B 'd' … ICODE UID 'e' … ICODE EPC 'i' … ICODE 's' … SR176 't' … activate all tags 'v' ... ISO 15693 Answer Answer Description 'OA' 'OB' 'OD' 'OE' 'OI' 'OS' 'OT' 'OV' String of tag type Example Command Description oa Sets the reader device to address ISO14443-A type tags. Innovision Jewel tag Innovision Jewel tag is part of ISO 14443 Type A. It can not be separately switched on/off. Page 64 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.12 Set Configuration Flags This command allows setting some configuration flags just in time; no reset is needed. The values are not stored in the EEPROM; therefore, the changed values are not available after a reset. Command Command Data of flag type (1 byte) data (1 byte) Answer Answer Description Data (1 byte) Current state of changed flag. 'R' Error: Out of range Example Command Description of0101 Answer: 01 Enables the New Serial Mode flag. November 4, 2008 Page 65 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Flag Types The following table shows the Flag Type with its corresponding flag from the specified Protocol Configuration Register. Flag Type Table 25 Flag Type with corresponding flag Protocol Configuration Valid Corresponding Flag Register values 00h Multitag 1 00 / 01 01h New Serial Mode 1 00 / 01 02h LED 1 00 / 01 03h Single Shot 1 00 / 01 04h Extended Protocol 1 00 / 01 05h Extended ID 1 00 / 01 06h Disable Multitag Reset 2 00 / 01 07h Noisy Environment 2 00 / 01 08h Reset Recovery Time Multiplier 2 00 … 03 09h Enable ISO14443 B Anti-collision 2 00 / 01 0Ah Disable ISO14443-4 Error Handling 2 00 / 01 0Bh Disable automatic ISO14443-4 timeouts 3 00 / 01 0Dh Page Read 3 00 / 01 11h ReqA Extended ID 3 00 / 01 12h Disable Read after Write 4 00 / 01 13h SAK Extended ID 3 00 / 01 14h WupA/B 4 00 / 01 15h CID Extended ID 4 00 / 01 16h Internal use / Do not change 8.3.24.12.1 Out of range failure 'R' The entered flag type is out of range. Page 66 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.13 Set Configuration Register This command allows setting some configuration registers just in time; no reset is needed. The values are not stored in the EEPROM; therefore the changed values are not available after a reset. Command Command Data og Register type (1 byte) data (1 byte) Answer Answer Description Data (1 byte) Current state of changed register. 'R' Error: Out of range Example Command Description og0450 Answer: 50 Sets the Reset Recovery Time to 50h. Register Types The following table shows the Register Type with its corresponding register. Register Type Table 26 Register Type with corresponding register Corresponding Register 00h Single shot time-out value 01h Internal use / Do not change 02h Internal use / Do not change 03h Reset Off Time 04h Reset Recovery Time 05h ISO 14443A Selection Time-out 06h ISO 14443B Selection Time-out 07h SR176 Selection Time-out 08h AFI 0Ch Page Read Start 0Dh Page Read Number 0Eh Command Guard Time 0Fh CID 10h Internal use / Do not change November 4, 2008 Page 67 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.13.1 Out of range failure 'R' The entered register type is out of range. 8.3.24.14 Reread all register This command rereads and applies all register settings. Command Command Data ox none Answer Answer Description Data (3 bytes) 'X' + new protocol + new baud rate Example Command Description ox Answer: X0106 binary protocol and 460800 baud active New protocol 00h means ASCII and 01h means binary protocol. New baud rate Values of 00h-06h are valid. For baud rate values refer to baud rate register. Page 68 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.15 Antenna power on/off This command controls the antenna power. It can be used to decrease the power consumption of the reader. Command Command Data 'pon' Switch reader on 'poff' Put reader in standby mode Answer Answer Description 'P' Positive acknowledge Example Command Description poff Put reader in standby mode 8.3.24.15.1 Power off The reader enters standby mode. Power consumption is decreased. All tags in the antenna field are powered off and reset. Standby mode is only entered manually. To switch off the whole unit, pin 16 (Enable) has to be set to logic low. 8.3.24.15.2 Power on The reader leaves standby mode and is ready for the next command. Sending a tag command (i.e. select, continuous read) the reader is powered up. November 4, 2008 Page 69 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.16 Read/Write user port This command sets or reads the state of the user port (pin 14) of the OEM reader device. The port is set either as output or as input. Command Command Data 'pr' None 'pw' State of user port (1 Byte) Answer Answer Description Data State of user port (1 Byte) 'C' Error: Error correction fails 'F' Error: Transmission Error / No answer received Example Command Description pr Reads user port pw01 Sets user port state to high 8.3.24.16.1 Read port The port read command returns the current state of the USER port. Port state Table 27 Read USER port return values Description 00h USER port is low 01h USER port is high Page 70 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.16.2 Write port If user port is used as an output, a 1kΩ resistor has to be integrated into the wire. Otherwise the reader device can be damaged. Port state Table 28 Write User port settings Description 00h Sets USER port to low 01h Sets USER port to high 02h – 7Fh RFU 80h - FFh Sends a serial data frame and checks the received frame Sending a Data Frame If the highest bit (MSB) is set in the State of the User Port, the command sends a serial data frame out the USER port. The frame includes a start bit, 8 data bits, parity bit and a stop bit. Transmit Frame Table 29 Sending Serial Data Frame Description Low Start bit Low RFU Data Bit 6 State of the User Port Bit 6 Data Bit 5 State of the User Port Bit 5 Data Bit 4 State of the User Port Bit 4 Data Bit 3 State of the User Port Bit 3 Data Bit 2 State of the User Port Bit 2 Data Bit 1 State of the User Port Bit 1 Data Bit 0 State of the User Port Bit 0 Parity Bit Even Parity Bit High Stop Bit November 4, 2008 Page 71 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 After 2ms Guard Time the answer should be received on the User Port otherwise an error is returned. Table 30 Receiving Serial Data Frame Description Receive Frame Low Start bit Error Bit If set, an error was detected. Data Bit 6 State of the User Port Bit 6 Data Bit 5 State of the User Port Bit 5 Data Bit 4 State of the User Port Bit 4 Data Bit 3 State of the User Port Bit 3 Data Bit 2 State of the User Port Bit 2 Data Bit 1 State of the User Port Bit 1 Data Bit 0 State of the User Port Bit 0 Parity Bit Even Parity Bit High Stop Bit If the Error bit is set or the Parity Bit is not correct, the Write User Port command returns an error code. 8.3.24.17 Quiet This command sets a selected tag into halt state. Only ISO14443 A+B and SR176 tags are supported. Command Command Data 'q' None Answer Answer Description 'Q' Halt state successfully set. 'N' Error: No Tag in the field 8.3.24.17.1 ISO 14443 Type A With ISO14443-3 Type A tags, the Quiet command always answers with 'Q' because the halt command does not send any acknowledge. In Part 4 a 'Deselect' command will be performed. 8.3.24.17.2 ISO 14443 Type B Some ISO14443 Type B tags do not support this command or do not respond. ‘Quiet’ is an ISO 14443-4 command, so it will work only if the ‘Deselect’ command is supported by the corresponding transponder. Page 72 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.17.3 SR176 With SR176 tags the Quiet command always answer with 'Q' because the completion command does not send any acknowledge. 8.3.24.18 Resend Last Answer This command resends the last answer from the internal serial buffer of the reader. Command Command Data 'ra' Resend last answer 8.3.24.19 Read block This command reads a data block on a card. The size of the returned data depends on the tag used. The block address range depends on the tag as well. Command Command Data 'r' Block address (1 byte), valid range 00h – 40h 'rb' Block address (1 byte) Answer Answer Description Data data block (depends on tag type) 'F' Error: read failure 'N' Error: No tag in field 'O' Error: Operation mode failure 'R' Error: Out of range Example Command Description rb05 Reads block 05. 8.3.24.19.1 Read failure 'F' This error is returned if either the reader receives bad data or the block address exceeds the block address range of the sector. 8.3.24.19.2 No tag in field 'N' The tag does not respond. There is either no tag present or addressed. November 4, 2008 Page 73 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.19.3 Operation mode failure 'O' The presented tag is not ISO14443 type A, SR 176, ICode, ICode-UID and ISO 15693 compliant. For ISO 14443 type A only MIFARE® tags are supported. 8.3.24.19.4 Out of range failure 'R' The block address of the 'r' command is higher than 40h. The block address of the 'r' command conflicts with other commands, therefore the block address has to be limited to 40h. Use the 'rb' command instead. 8.3.24.20 Read data (multiple blocks) This command reads multiple data blocks on a card. The size of the returned data depends on the tag used. The block address range depends on the tag as well. Command Command Data 'rd' Start block address (1 byte) Number of blocks to read (1 byte) Answer Answer Description Data data block (depends on tag type) 'F' Error: read failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description rd0504 Reads 4 blocks starting with block 05. 8.3.24.20.1 Read failure 'F' This error is returned if either the reader receives bad data or the block address exceeds the block address range of the sector. 8.3.24.20.2 No tag in field 'N' The tag does not respond. There is either no tag present or addressed. Page 74 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.20.3 Operation mode failure 'O' The presented tag is not ISO14443 type A, SR 176, ICode or ISO 15693 compliant. For ISO 14443 type A only MIFARE® tags are supported. 8.3.24.21 Read reader EEPROM This command reads the internal reader EEPROM. It contains all start-up parameters and the device ID. Changes in the start-up settings will only go into effect after a reset of the device. Command Command Data 'rp' EEPROM address (1 byte) 00h … EFh Answer Answer Description Data EEPROM data (1 byte) 'R' Error: Out of range failure Example Command Description rp0B Reads protocol configuration register. 8.3.24.21.1 Out of range failure 'R' The entered EEPROM address is not valid. 8.3.24.22 Select This command selects a single card in the antenna field. It can only be used in single tag mode. If successfully executed, the command returns the UID of the selected card. The reader detects the length of the UID automatically. Command Command Data 's' None Answer Answer Description Data serial number 'N' Error: No Tag in the field Example Command Description s 1234567890ABCD Select the card with UID 1234567890SABCD. November 4, 2008 Page 75 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.22.1 Select a single tag No previous continuous read is required. The command executes an automatic field reset. 8.3.24.22.2 Extended ID See above for more information on Extended ID. 8.3.24.22.3 Multiple tags This command is designed for fast access of a single tag in the field. If multiple cards are used the 'm' instruction has to be used instead. 8.3.24.23 Get Version This command returns the current version of the reader module. Command Command Data 'v' None Answer Answer Description 'MultiISO 1.0' + + ASCII Mode 02 00 0C 4D 75 6C 74 69 49 53 4F 20 31 2E 30 1F 03 Binary Mode Example Command Description v ‘MultiISO 1.0’ Version of the reader module Page 76 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.24 Write block This command writes data to a block. Command Command Data 'w' Block address (1 byte), valid range 00h – 40h Data (n bytes) 'wb' Block address (1 byte) Data (n bytes) Answer Answer Description Data Data block (depends on tag type) 'F' Error: Write failure 'N' Error: No tag in field 'O' Error: Operation mode failure 'R' Error: Out of range Example Command Description wb0511223344 Writes data 11223344 on block 05. 8.3.24.24.1 Write failure 'F' This error is displayed if bad transmission conditions are given. If the block address exceeds the physical number of blocks of a tag, this error is shown. 8.3.24.24.2 No tag error 'N' This error is returned if no tag is present or the card does not respond. 8.3.24.24.3 Operation mode failure 'O' The presented tag is not ISO14443 type A, SR 176, ICode, ICode-UID and ISO 15693 compliant. For ISO 14443 type A only MIFARE® tags are supported. 8.3.24.24.4 Out of range failure 'R' The block address of the 'w' command is higher than 40h. The block address of the 'w' command conflicts with other commands, therefore the block address has to be limited to 40h. Use the 'wb' command instead. November 4, 2008 Page 77 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.24.5 Disable Read after Write A read is done automatically after every write to ensure correct writing. If the "disable Read after Write flag" is set no read is done, and the returned data is a 00h byte in case of successfully written data. 8.3.24.25 Write data (multiple blocks) This command writes multiple blocks to a card. Command Command Data 'wd' Start block address (1 byte) Number of blocks (1 byte) Data (n bytes) Answer Answer Description Data Data block (depends on tag type) 'F' Error: Write failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description wd050211223344556 Writes data 11223344 on block 05 and 55667788 on block 06. 67788 8.3.24.25.1 Write failure 'F' This error is displayed if bad transmission conditions are given. If the block address exceeds the physical number of blocks of a tag, this error is shown. 8.3.24.25.2 No tag error 'N' This error is returned if no tag is present or the card does not respond. 8.3.24.25.3 Operation mode failure 'O' The presented tag is not ISO14443 type A, SR 176, ICode or ISO 15693 compliant. For ISO 14443 type A only MIFARE® tags are supported. Page 78 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.24.25.4 Disable Read after Write A read is done automatically after every write to ensure correct writing. If the "disable Read after Write flag" is set no read is done, and the returned data is a 00h byte in case of successfully written data. 8.3.24.26 Write EEPROM Writes to the internal reader EEPROM. It contains all start-up parameters and the device ID. Changes to the start-up settings will only go into effect after a reset of the device. Command Command Data 'wp' Address (1 byte), valid range 0Ah - EFh Data (1 byte) Answer Answer Description Data EEPROM data (1 byte) 'F' Error: Read after write failure 'R' Error: Out of range failure Example Command Description wp0A01 Set EEPROM address 0A (Station ID) to 01h 8.3.24.26.1 Out of range failure 'R' The entered address exceeds the address range. November 4, 2008 Page 79 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.24.27 Reset This command executes a power on (software) reset. New configuration settings will be loaded. It resets all tags in the antenna field. Command Command Data 'x' None Answer Answer Description MultiISO 1.0' + + ASCII Mode None Binary Mode 8.3.24.27.1 Disable Start-up Message If the start-up message is disabled in the protocol configuration register 2, the ASCII mode does not respond with the version of the reader. 8.3.24.27.2 Reset Timing The power up timing depends on environmental conditions such as voltage ramp up. For handheld devices the timing can vary based on the charge state of the battery. 8.3.24.27.3 Field Reset The field reset switches off the antenna field for the specified duration. All tags need a certain amount of time to initialize before a command can be processed. The second byte specifies the field recovery time. Command Command Data 'y' Off time in milliseconds (1 byte) Field recovery time in milliseconds (1 byte) Answer Answer Description 'Y' After the field reset the reader sends back a ‘Y’ to acknowledge the command. Page 80 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.25 ISO 14443 Type A (MIFARE®) only commands 8.3.25.1 Increment value block (credit) Increments a value block with a defined value. A read is done automatically after a write to verify data integrity. The command fails if the source block is not in value block format. A previous login is needed to access a block. Command Command Data '+' Block (1 byte) Value (4 bytes) Answer Answer Description Data Value (4 bytes) 'I' Error: value block failure 'F' Error: increment failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description +0400000001 Adds 1 to value block 4 +0500000100 Adds 256 to value block 5 8.3.25.1.1 No value block 'I' Specified block does not match the value format. The value block is corrupted. A backup block can be used to restore the correct value. 8.3.25.1.2 Increment failure 'F' This indicates a general failure during the increment procedure or an inability to read after the write process. 8.3.25.1.3 No tag error 'N' The reader does not detect a response from the tag. There is either no tag present or the tag does not respond to the request. 8.3.25.1.4 Operation mode failure 'O' The tag is not ISO14443 type A compliant. November 4, 2008 Page 81 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.25.2 Decrement value block (debit) Decrements a value block with a defined value. A read is done automatically after the write to verify data integrity. The command fails if the source block is not in value block format. A previous login is needed to access a block. Command Command Data '-' Block (1 byte) Value (4 bytes) Answer Answer Description Data Value (4 bytes) 'I' Error: value block failure 'F' Error: decrement failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description -0400000001 Subtract 1 to value block 4 -0500000100 Subtract 256 to value block 5 8.3.25.2.1 No value block 'I' Specified block does not match the value format. The value block is corrupted. A backup block can be used to restore the correct value. 8.3.25.2.2 Decrement failure 'F' This indicates a general failure during the decrement procedure or an inability to read after the write process. 8.3.25.2.3 No tag error 'N' The reader does not detect a response from the tag. There is either no tag present or the tag does not respond to the request. 8.3.25.2.4 Operation mode failure 'O' The tag is not ISO14443 type A compliant. Page 82 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.25.3 Copy value block (backup) Copies a value block to another block of the same sector. A read is done automatically after the write to ensure data integrity. Used for backup and error recovery. A previous login is needed to access a block. Command Command Data '=' Source block (1 byte) Target block (1 byte) Answer Answer Description Data New value of target block (4 bytes). 'I' Error: value block failure 'F' Error: copy failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description =0405 Copy value block 4 to block 5 =0506 Copy value block 5 to block 6 8.3.25.3.1 Target block The target block does not need to be a valid value block. If the source block is not in value format, the command fails. 8.3.25.3.2 No value block 'I' Source value block is not in a valid value block. The value block is corrupted. A backup block can be used to restore the correct value. 8.3.25.3.3 Copy failure 'F' This indicates a general failure during the copy procedure or an inability to read after the write process. 8.3.25.3.4 No tag error 'N' The reader does not detect a response of the tag. There is either no tag present or the tag does not respond to the request. 8.3.25.3.5 Operation mode failure 'O' The tag is not ISO14443 type A compliant. November 4, 2008 Page 83 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.25.4 Login (authenticate tag) Performs an authentication in order to access one sector of a MIFARE® card. Only one sector can be accessed at a time. Command Command Data 'l' Sector (1 byte), valid range 00h - 3Fh Key type (1 byte) AAh authenticate with key type A FFh authenticate with key type A, transport key FFFFFFFFFFFFh BBh authenticate with key type B 10h … 2Fh authenticate with key type A using stored key (00h … 1Fh) 30h … 4Fh authenticate with key type B using stored key (00h … 1Fh) Key (6 bytes) / (1 byte), optional By transmitting instead of the keydata authentication is done with manufacturer’s transport keys (A0A1A2A3A4A5h, B0B1B2B3B4B5h, FFFFFFFFFFFFh). Answer Answer Description data Login status (1 byte) 'L' Login success 'F' Error: General failure 'N' Error: No tag 'O' Error: Operation mode failure 'R' Error: Out of range 'X' Error: Authentication failed Example Command Description l02AA Authenticate for sector 2, using the transport key A (A0A1A2A3A4A5h, key type A) l3FBB Authenticate for sector 63, using the transport key 2 (B0B1B2B3B4B5h, key type B) l04FF Authenticate for sector 4, using the transport key 3 (FFFFFFFFFFFFh, key type A) l0FAAFFFFFFFFFFFF Authenticate for sector 15, using key FFFFFFFFFFFFh, key type A l0E14 Authenticate for sector 14, using EEPROM key 4, key type A l0530 Authenticate for sector 5, using EEPROM key 0, key type B l0732 Authenticate for sector 7, using EEPROM key 2, key type B l0110 Authenticate for sector 1, using EEPROM key 0, key type A l0ABBFF12FFFFFF35 Authenticate for sector 10, using key FF12FFFFFF35h, key type B Page 84 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.25.4.1 No tag error 'N' The reader does not detect a response from the tag. There is either no tag present or the tag does not respond to the request. 8.3.25.4.2 Operation mode failure 'O' The tag is not ISO14443 type A compliant. 8.3.25.4.3 Out of range failure 'R' The entered key type or the sector is out of range. 8.3.25.4.4 Three transport keys are implemented to access cards quickly. By transmitting instead of the key, the reader module uses the transport keys for the login procedure. Command Description LxxAA Authenticate for sector xx, using the transport key 1 (A0A1A2A3A4A5h, key type A) LxxBB Authenticate for sector xx, using the transport key 2 (B0B1B2B3B4B5h, key type B) LxxFF Authenticate for sector xx, using the transport key 3 (FFFFFFFFFFFFh, key type A) 8.3.25.4.5 Login with key data from EEPROM Each key stored in the reader EEPROM can be used as type A or type B key. To use a key as type A, the value 10h must be added to the key index. 30h must be added to use a key as type B. 8.3.25.4.6 Usage of key A, key B MIFARE® cards support two different crypto keys for each sector. Each key is 32 bits long and is stored in the sector trailer (last block of the sector) on the card. It is possible to set different access rights for each key. November 4, 2008 Page 85 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.25.5 Read value block Reads a value block. The command checks if data is in value block format. The read value block command needs a successful login. Command Command Data 'rv' Value block (1 byte) Answer Answer Description Data Read value (4 bytes) 'F' Error: General failure 'I' Error: value block failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description rv04 Reads value of block 4. 8.3.25.5.1 No value block 'I' The value read back after the write value command is not a value block. Data was written corruptly. 8.3.25.5.2 No tag error 'N' This means that the tag does not respond, because either there is no tag present or none of the tags in the field are authenticated ('l' instruction). 8.3.25.5.3 General failure 'F' In addition to the case of a data read failure caused by bad transmission conditions, this error is returned if a sector is addressed which is not located in the authenticated area. 8.3.25.5.4 Operation mode failure 'O' The tag is not ISO14443 type A compliant. Page 86 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.25.6 Write value block This command formats a block as a value block containing a 32-bit value. Value blocks need a complete 16-byte block due to redundant storage. A successful login is required to run the command. Command Command Data 'wv' Value block (1 byte) Value (4 bytes) Answer Answer Description Data Written value (4 bytes) 'I' Error: value block failure 'F' Error: write failure 'N' Error: No tag in field 'O' Error: Operation mode failure Example Command Description wv05010055EF Writes value 010055EFh to block 5. 8.3.25.6.1 Invalid value 'I' The value read back after the write value command is not a value block. Data was written corruptly. 8.3.25.6.2 Write failure 'F' In addition to the case of a data read failure caused by bad transmission conditions, this error is returned if a sector is addressed which is not located in the authenticated area. 8.3.25.6.3 No tag error 'N' This error is returned if no tag is present or the card does not respond. 8.3.25.6.4 Operation mode failure 'O' The tag is not ISO14443 type A compliant. 8.3.25.6.5 Writing values The write value block command is designed to create blocks in value format. This command requires write access to the specified block. Using this instruction for ticketing operations is not recommended. For ticketing applications, special instructions (Increment/Decrement/Copy) are available. November 4, 2008 Page 87 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.25.6.6 Disable Read after Write A read is done automatically after every write to ensure correct writing. If the "disable Read after Write flag" is set no read is done, and the returned data is a 00h byte in case of successfully written data. 8.3.26 Key Management The Key Management is able to store up to 32 keys and is also able to manage 3 different key types. If no key is available to login into the reader, it is possible to reset the key table without any authentication. Key type Description 01 my-d™ secure key 02 DES key 03 MIFARE® key 8.3.26.1 Authenticate to reader This command logs into a reader. Only my-d™ secure and DES keys are allowed to login into reader. After successful log in the key table of the reader can be changed. The authentication does 2 two-pass authentications, defined in ISO 9798 part 2, within two steps. Following commands need a prior log in: • Update key • Update key access rights • Change key type • Reset key table Command Command Data Step 1: 'ar' Option x1h (1 byte) Key type (1 byte) Key index (1 byte) Step 2: 'ar' Option x2h (1 byte) Random number key Management (8 bytes) MAC key Management (8 bytes) Answer Answer Description Step 1 Random number reader (8 bytes) Step 2 MAC reader (8 bytes) Page 88 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Option The option byte defines the authentication step and type of authentication. Bit Description 0-1 Authentication Steps 0: Log out 1: Step 1 2: Step 2 2–6 RFU 7 Authentication Algorithm 0: 2 two pass authentications 1: RFU Key index The key index of Step 1 points to a valid key with the access rights to login into the reader. The key index is zero based. Log out It is possible to log out with Authentication Step 0. Default Keys The following keys are default: Key Type Key my-d™ 01020407080B0D0E10131516191A1C1Fh Default Master key DESFire 00000000000000000000000000000000h MIFARE ® A0A1A2A3A4A5h MIFARE ® B0B1B2B3B4B5h MIFARE® FFFFFFFFFFFFh November 4, 2008 Page 89 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Two-Pass Authentication Flow Diagram Host Reader 1. Start Authentication Step 1 StartAuth Æ 2. Generate Random number RndRdr Å RndRdr 3. Reply Random number 4. Generate Random number RndH 5. Calculate the MAC of the key management MacH = Enc(RndRdr) 6. Transmit Random number and MAC: RndKm,MacH RndKm,MacH Æ 7. Check the received MacH RndRdr = Dec(MacH) 8. Calculate the MAC of the reader MacRdr = Enc(RndH) Å MacRdr 9. Reply MAC 10. Check the received MacRdr RndH = Dec(MacRdr)? Page 90 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.26.2 Get Key Access Rights This command returns the access rights of a key. Command Command Data 'ia' Key type (1 byte) Key index (1 byte) Answer Answer Description Data Access rights (2 bytes). Higher Byte is send first Access Rights Only the default master key has all access rights. New keys got the default value 0000h. Bit Description 0 Allow Add Key 1 Allow Update Key 2 Allow Delete Key 3 Allow Reset Key table 4-7 RFU 8 RFU (Disable Serial Encryption) 9 Disable Authentication Tag 10 Allow Authentication Reader 11 Allow Changing Access rights 12 Allow Key Type changing 13 Allow 'ds' encryption 14 - 15 RFU November 4, 2008 Page 91 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.26.3 Get key status This command reports the key status of the reader. The reader lists for each key the key information. This command is used to inform the key management about the key status. The first byte of the response lists the number of stored keys. Command Command Data ‘it’ key type (1) Answer Answer Description my-d™ secure Data Number of keys (1 byte) [Key information (8 bytes)] Free User part (1 byte) Project ID (3 bytes) Logical Sector ID (1 byte) Key type (1 byte) KVV (2 bytes) DES Data Number of keys (1 byte) [Key information (10 bytes)] Option byte (1 byte) Free User part (9 bytes) MIFARE® Data Number of keys (1 byte) [Key information 10 bytes)] Free User part (10 bytes) More than 255 bytes If the amount of data exceeds 255 bytes, than the answer is divided into more frames. If a frame follows, the Number of keys byte is extended with a set MSB (80h). 8.3.26.4 Reset key table The reset key table clears all key entries in the reader. Afterwards the default keys are loaded automatically. It is only allowed to reset the key table after a successful authentication to the reader. If no keys are available to login into the reader, it is possible to reset the key table without an authentication. Command Command Data ‘rt’ None Answer Answer Description ‘RT’ In case of success Page 92 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.26.5 Update key access rights This command is able to change the access rights of a key. It is only allowed to change the access rights after a successful authentication to the reader with a key permitted to change the access rights. Command Command Data ‘ua’ Key type (1 byte) Key index (1 byte) Access rights (2 bytes) Answer Answer Description Data Access rights (2 bytes). Higher Byte has to be sent first. Access rights For more detailed information refer to "Get key access rights". 8.3.26.6 Change key type This command is able to change the key type. Be sure the key information data are suitable to the key type. It is only allowed to change the key type after a successful authentication to the reader with a key permitted to change the key type. Command Command Data ‘uc’ Key type (1 byte) Key index (1 byte) New key type (1 bytes) Answer Answer Description Data Access rights (2 bytes) November 4, 2008 Page 93 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 8.3.26.7 Update key The update key command stores, modifies or deletes a key in the reader key table. A key is identified with its key information data. The key information data has to be unique within the same key type. If a key is erased the key data must be dropped. It is only allowed to update the key type after a successful authentication to the reader with a key permitted the necessary rights. Command Command Data my-d™ secure ‘uk’ Key type 01h (1 byte) Action (1 byte) Key information data (8 bytes) Free User Part (1 byte) Project ID (3 bytes) Logical Sector ID (1 byte) Key type (1 byte) KVV (2 bytes) Key Data (8 / 16 bytes) DES 'uk' Key type 02h (1 byte) Action (1 byte) Key information data (10 bytes) Option (1 byte) Free user part (9 bytes) Key Data (16 bytes) MIFARE® 'uk' Key type 03h (1 byte) Action (1 byte) Key information data (10 bytes) Free user part (10 bytes) Key Data (16 bytes) Answer Answer Description Data Index of key (1 byte) Page 94 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Action The Action byte defines the action of the key. Action Description Axh Add / Update key 5xh Delete Key x1h my-d™ secure key A x2h my-d™ secure key B my-d™ secure key For more detailed information on key information data refer to Infineon documentation. DES key option byte Bit Description 0 0 … 16 byte key 1 … 8 byte key 1-7 RFU In case of an 8-byte key, the first 8 bytes of the key data are valid. MIFARE® key Only the first 6 bytes of key data are valid. Number of stored keys The key management is able to store up to 32 keys. Encryption Key Data for DESFire and MIFARE® keys has to be encrypted with the login key in CBC mode. my-d™ S keys are enciphered every 8 byte block separately without CBC mode. November 4, 2008 Page 95 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 CBC mode The data stream has to be divided into blocks of 8 bytes. The last enciphered block has to be XORed with the next plain block. block2 Enc Enc(block1) Enc(block2) XOR 8.3.27 my-d™ secure Note that ISO 14443 tags do not support the addressed mode. Bit 5 and 6 of the option byte are not used with ISO 14443 tags. The ISO 14443 tag only works in selected mode. 8.3.27.1 Abort KTT upload This command aborts the Prepare for KTT ‘ut’ command, if the reader is in prepare for KTT awareness mode. Command Command Data ‘*’ None Answer Answer Description 00h Prepare for KTT successfully aborted ‘F’ Prepare for KTT was not active No response Key uploading is in progress Page 96 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.27.2 Authenticate to sector The Authenticate to sector command sets up a secured transmission to a transponder. Command Command Data ‘as’ Option byte (1 byte) [UID (8 bytes)] Key page (1 byte) Key index (1 byte) Counter page (2 byte) Diversification data (8 bytes) Answer Answer Description ‘L’ In case of success Option byte The option byte defines the general behavior of the command. Note that ISO 14443 tags are only working in selected mode. Bit Description 7 RFU 6 If set the tag is in addressed mode. The UID is following as first 8 bytes after the option byte. The my-d™ frame is following. 5 If set the tag is selected. No UID is needed. 4-0 RFU Key page This byte defines the key page number of the transponder Key index Defines the reader key index. If the index exceeds the key index of the reader the error ‘R’ out of range is thrown. The key index is zero based. Counter page This page number points to the authentication counter page. Lower byte of the page number is sent first. November 4, 2008 Page 97 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Diversification data This data is used to diversify the key data. Example Command Answer / Description 'as20040103000000000000000000' 'L' Login into tag. 8.3.27.3 Issue transponder key Writes a diversified key to the transponder. This command uses the write and Reread my-d™ command. Command Command Data ‘ik’ Option byte (1 byte) [UID (8 bytes)] Key index (1 byte) Destination page (2 bytes) Diversification data (8 bytes) [Sector index and access conditions (2 bytes)] Answer Answer Description ‘IK’ Key successfully written Page 98 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Option byte The option byte defines general behavior of the command. Note that ISO 14443 tags are only working in selected mode. Bit Description 7 If set the user mode is used and the MAC is calculated and added to the frame. If not set the issuer mode is used sector index and access conditions are included and no MAC is calculated. 6 If set the tag is in addressed mode. The UID is following as first 8 bytes after the option byte. The my-d™ frame is following. 5 If set the tag is selected. No UID is needed. 4-0 RFU Key index Defines the reader key index. If the index exceeds the key index of the reader the error ‘R’ out of range is thrown. The key index is zero based. Destination page Defines the transponder page index. Lower byte of the page number is sent first. Sector index and access conditions In issuer mode the sector index and the access conditions are added. 8.3.27.4 Prepare for KTT This command sets the reader into KTT awareness mode. Command Command Data ‘ut’ Key page (1 byte) Key index (1 byte) Counter page (2 bytes) Diversification data (8 bytes) Answer Use the check KTT upload status ‘!’ command to finish the upload procedure. LED activity The green and red LED indicates the state of the upload process. Mode LED activity Awareness Red and green LEDs are flashing slow Upload in progress Green LED is active Error during upload Red LED is flashing fast until the ‘!’ command is received detected Upload finished successfully Green LED is flashing fast until the ‘!’ command is received Upload aborted Red LED is active for 1 second November 4, 2008 Page 99 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 State diagram Prepare for KTT triggered 'ut' (no antenna field) no tag found Searching tags Awareness mode tag found other tag found Check for valid KTT valid KTT found Upload all keys from KTT into Key management OK Error during Upload Upload ready get upload result '!' Return Upload result Page 100 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 8.3.27.5 my-d™ command This command sends and receives my-d™ plain and secure commands including my-d™ secure algorithm. Command Command Data ‘z’ Downlink length (1 byte) Option byte (1 byte) [UID (8 bytes)] my-d™ data (n bytes) Answer Answer Description Data Status byte: 00h (1 byte) Data without MAC and CRC (n bytes) Downlink length This byte is mandatory. It will define the length of the my-d™ data frame sent to the reader. The MAC, CRC and the framing overhead is not included. Option byte The option byte defines general behavior of the command. Note that ISO 14443 tags are only working in selected mode. Bit Description 7 If set the MAC is calculated and added to the frame 6 If set the tag is in addressed mode. The UID is following as first 8 bytes after the option byte. The my-d™ frame is following. 5 If set the tag is selected. No UID is needed. 4-0 RFU Data Data is sent as my-d™ plain command. It contains only data that is processed by the MAC calculation. If the tag is addressed, only valid with ISO 15693 tags, with its UID the first 8 bytes are interpreted as UID and not included into the MAC calculation. MAC calculation is done automatically if according flag is set. The ISO 15693 or the ISO 14443 frame is completed and the CRC is computed and added automatically. The commands Write Page, Restricted Write and Write Byte do not need any MAC verification for the answer. November 4, 2008 Page 101 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 9 Frequently Asked Questions 9.1.1 Getting Started To test and interface the Dual ISO Module, you do not need a sophisticated µP development system. All you need is a PC, a connection cable and a power supply for the reader. If you are using Microsoft Windows (95/98/NT/…), take the following steps: • Make sure, that your reader has an RS232 interface • Start HyperTerminal • Create a new connection (FILE/NEW CONNECTION) • Enter a name for the connection (i.e. ‘MIFARE’) • Select connect COM2 (COM1) direct connection • Connection setup 9600,8,n,1,no handshake • Connect your reader to COM2 (COM1) of the PC and apply appropriate supply voltage. The reader transmits a string (“MultiISO 1.0”) to the PC. • This string denotes the firmware provided with your reader module • Put a tag to your reader. Serial numbers should be displayed properly • Enter commands via keyboard. They should be transmitted to the reader and the reader should reply If using an operating system different from Microsoft Windows, you may use any other terminal program that is capable of receiving/transmitting data via the serial port of your PC. 9.1.2 How should the Multi ISO Reader be personalized? In ASCII protocol applications, no personalization is necessary. In applications that are using the binary protocol mode, personalization is required. Use the Utility program to set up your reader correctly. Contact support: eusupport@hidglobal.com to acquire the utility. Minimum requirements are WIN98SE, WIN 2000, WIN XP and a free COM port on the PC. 9.1.3 What type of MIFARE® card should I use? The MIFARE® standard is designed for multi-application environments. It contains 16 sectors each with 2 individual keys, access conditions, and 3 data or value blocks. Some applications use the 1 Kbytes of the MIFARE® Standard Card Memory only as storage area. MIFARE® Ultra light has no crypto unit on chip. It only supports 16 blocks. MIFARE® Standard 4k cards have the same features as MIFARE® Standard cards but increased memory capacity. Page 102 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 9.1.4 Using a MIFARE® card This example demonstrates the detection of a card in the antenna field with continuous read and the reading of a page. Command c Table 31 Using a MIFARE® card Answer Activate continuous read mode B2197B58 a card responds with its serial number . S abort continuous read mode s B2197B58 select card l01AAFFFFFFFFFFFF L login into sector 1 with key FFFFFFFFFFFFh key type A rb04 00112233445566778899AABBCCDDEEFF read block 04 c Activate continuous read mode to detect a new card 9.1.5 Using NFC The example shows how to communicate with NFC using the NFC demoboard PN531. The reader is the initiator. The NFC has to be configured as passive target using MIFARE® 106kbps (other NFC modes are not supported). As first step place the reader on top of the NFC demoboard antenna in 3 cm distance. Then load the "passive_target_106.cmd" file from the "Scripts\Tama\P2P" subfolder into the SCRTester application. Run the code. Now it is possible to get a serial number from the NFC. Command s Table 32 Get a serial number from NFC Answer 08123456 November 4, 2008 Page 103 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 References [1] ISO/IEC 14443 Part 1-4, Identification Cards – Contact less integrated circuit(s) cards – Proximity cards [2] DESFire Documentation, NXP; www.nxp.com [3] Data Encryption Standard (DES), FIPS PUB 46-3, Reaffirmed 1995 October 25 [4] HID Antenna Design Guide [5] Philips; Application Note, MIFARE® & I-Code, Micore Reader IC family Directly Matched Antenna Design Appendix A - SAM Note: The power supply of the SAM adapter must be turned off during the entire card insertion period; otherwise SAM card damage may occur. For proper usage of the SAM, a 100nF capacitor between Vcc and GND is necessary. Page 104 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Appendix B Compact Serial Plug & Play Module (RDHC-020xN0-02) Features • • • • • • • • • Interface type: RS232 Dimensions: 70x45x12.1 (LxWxH), all in mm Reading Distance: up to 75mm, depending on the tag SAM: supported Boot loader: supported (²) Drivers: virtual COM port driver, DLL driver available Antenna: on board Signaling: reading LED, power LED Power Supply: 5VDC ± 10% regulated (²) The boot loader enables to download a firmware update via the serial interface to the unit without replacing/dismantling the hardware. November 4, 2008 Page 105 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Dimensions Top view All dimensions are listed in mm A 0 2,8 29,21 mm J3 J2 7 1 1,27 mm 3,00 mm SAM Socket 7,38 mm 41,06 mm 58,26 mm 62,00 mm J4 1 67,00 mm 1 10 70,00 mm 4 20 11 3,00 mm 11,07 mm A' 26,31 mm B' B 9,43 mm 40,83 mm 42,00 mm 43,00 mm 45,00 mm Page 106 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Side View All dimensions are listed in mm 9,00 View A-A' J3 J2 J4 Front View 9,00 All dimensions are listed in mm View B-B' 1,60 mm 3,10 mm J3 November 4, 2008 Page 107 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Pin Out – Jumper 3 7 1 J3 1 20 Figure 9 Pin out of jumper 3 PIN PIN No. Table 33 Pin out of jumper 2 Description RFU 1 RFU +5V 2 Supply Voltage GND 3 Ground RX/RXA 4 RS232 RX / RS422 RXA TX/TXA 5 RS232 TX / RS422 TXA RXB 6 RS422 RXB TXB 7 RS422 TXB Electrical characteristics of J3 PINs in RS232 Configuration. PIN PIN No. RFU 1 +5V 2 GND 3 RX/RXA 4 TX/TXA 5 Min Typ. Max. Description Do not connect 4.5V 5V 5.5V Supply Voltage 150mA 250mA Supply Current (without SAM) Ground for Power Supply and Interface GND -15V 3kΩ ±5V 300kΩ 5kΩ ±9V +15V 7kΩ RS232 Voltage Levels Input Impedance RS232 Voltage Levels Output Impedance RXB 6 Do not connect TXB 7 Do not connect Page 108 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 RS232 Configuration 1 1 J3 User Manual, Firmware V1.2 7 +5V Ground RX TX 20 Figure 10 Pin out of jumper 3 in RS232 Configuration Electrical characteristics of J3 PINs in RS422 Configuration PIN PIN No. RFU 1 +5V 2 GND 3 RX/RXA 4 Min Typ. Max. Description Do not connect 4.5V 5V 5.5V Supply Voltage 150mA 250mA Supply Current (without SAM) Ground for Power Supply and Interface GND -7V +12V RXA RS422 TX/TXA 5 -7V +12V TXA RS422 / Differential RXB 6 -7V +12V RXB RS422 TXB 7 -7V +12V TXB RS422 / Differential Typ. Description PIN No. Conditions Min Differential Output Voltage 4/6 Unloaded GND VCC Differential Output Voltage 5/7 Loaded: RL=50Ω 2V VCC November 4, 2008 Max. Page 109 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader RS422 Configuration 7 1 1 J3 User Manual, Firmware V1.2 +5V Ground RXA TXA RXB TXB 20 Figure 11 Pin out of jumper 3 in RS422 Configuration Electrical characteristics of J3 PINs in RS485 Configuration PIN PIN No. RFU 1 +5V 2 Min Typ. Max. Description Do not connect 4.5V 5V 5.5V Supply Voltage 150mA 250mA Supply Current (without SAM) Ground for Power Supply and Interface GND 3 GND RX/RXA 4 -7V +12V RX, connect to PIN 5 TX/TXA 5 -7V +12V TX RXB 6 -7V +12V RX, connect to PIN 7 TXB 7 -7V +12V TX Typ. Description PIN No. Conditions Min Differential Output Voltage 4/6 Unloaded GND VCC Differential Output Voltage 5/7 Loaded: RL=270Ω 1.5V VCC Page 110 of 125 Max. November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 1 J3 1 RS485 Configuration +5V Ground RXA / TXA 7 RXB / TXB 20 Figure 12 Pin out of jumper 3 in RS232 Configuration Pin Out - Jumper 4 1 4 J4 Figure 13 Pin out of Jumper 4 (top view) PIN PIN No. Description Read+ 1 Connector for green Read Indicator LED Read- 2 Connector for red Read Error Indicator LED Power- 3 Ground Power+ 4 Connector for Power Indicator LED November 4, 2008 Page 111 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Electrical characteristics of J4 PINs PIN PIN No. Read+ 1 Min Typ. Max. Description 1.4V @11mA VDDmax 11mA @15mA Read- 2 1.4V @11mA VDDmax 11mA @15mA Power- 3 GND Power+ 4 1.4V @11mA VDDmax 11mA 15mA LEDr LEDg 1 Power 2 3 4 J4 Figure 14 Pin out of jumper 4 Page 112 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Short Range Plug & Play Module (RDHS-0204N0-02) Features • Interface type: USB 2.0 • Dimensions: 110x70x14 (LxWxH), all in mm • Reading Distance: up to 90mm, depending on the tag • SAM: supported • Boot loader: supported (²) • Drivers: virtual COM port driver, DLL driver available • Antenna: on board • Signaling: reading LED, power LED • Power Supply: via USB (²) The boot loader enables to download a firmware update via the serial interface to the unit without replacing/dismantling the hardware. November 4, 2008 Page 113 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Dimensions All dimensions are listed in mm Read LED + Read LED Power LED Power LED + J5 1 10 110,00 12,00 66,40 106,50 J2 88,50 SAM Socket 83,60 ø 00 3, 20 11 USB J3 7,20 4,50 17,78 27,40 39,60 49,18 62,50 67,00 Figure 15 Short Range Plug & Play Module - Top view Page 114 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 22,07 44,93 12,70 3,00 2,00 11,00 Front View Figure 16 Short Range Plug & Play Module - Front View November 4, 2008 Page 115 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Read LED (Option 1) Power LED (Option 1) J2 Read LED (Option 2) USB Power LED (Option 2) 31,00 106,70 SAM Socket J3 21,00 46,00 Figure 17 Short Range Plug & Play Module - Bottom View Page 116 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Read LED + Read LED Power LED Power LED + Pin Out – Jumper 5 1 4 J5 Figure 18 Pin out of Jumper 5 - Top View PIN PIN No. Table 34 Pin out of jumper 5 Description Read+ 1 Connector for green Read Indicator LED Read- 2 Connector for red Read Error Indicator LED Power- 3 Ground Power+ 4 Connector for Power Indicator LED Electrical characteristics of J5 PINs PIN PIN No. Read+ 1 Table 35 Electrical characteristics of pins Min Typ. Max. Description 1.4V @11mA VDDmax 11mA @15mA Read- 2 1.4V @11mA VDDmax 11mA @15mA Power- 3 GND Power+ 4 1.4V @11mA VDDmax 11mA 15mA November 4, 2008 Page 117 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Short Range USB Desktop Reader (RDHS-0204D0-02) Features • Interface type: USB 2.0 • Dimensions: 155x82x35 (LxWxH), all in mm • Reading Distance: up to 80mm, depending on the tag • SAM: supported • Boot loader: supported (²) • Drivers: virtual COM port & PCSC driver available. DLL also available. • Antenna: on board • Signaling: reading LED, power LED • Power Supply: via USB (²) The boot loader makes it easy to download a firmware to the unit without replacing/dismantling the hardware. Page 118 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Plug-In Reader (RDHP-0206P0-02) Features • Interface type: CF Card Type II • Dimensions: (LxWxH) 86.50x43.0x10.0mm ± 0.1mm (LxWxH) • Reading Distance: up to 60mm, depending on the tag • SAM: not integrated • Boot loader: supported (²) • Drivers: virtual COM port driver, DLL driver available • Antenna: integrated • Signaling: reading LED integrated • Power Supply: via CF Card Interface (²) The boot loader makes it easy to download a firmware to the unit without replacing/dismantling the hardware. November 4, 2008 Page 119 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Appendix C - Timings tCMD tEXEC tRES Request → PC: ← Response Reader: Table 36 Timings Command tEXEC [ms] Comments 2.8 – 22.6 + Reset Off and Recovery Time Cont. read (worst case) 54 + 3x Reset Off and Recovery Time DES en/decryption 9.6 – 9.7 TDES en/decryption 28.7 – 28.8 High-speed select 'h08' (locked tag) 8.9 – 14.4 + Reset Off and Recovery Time + SFGT High-speed select 'h08' (no tag) 15 + 3x Reset Off and Recovery Time High-speed select 'h08' (worst case) 14.7 + 3x Reset Off and Recovery Time + SFGT Multi-select (locked tag) 5.8 – 11.4 + Reset Off and Recovery Time Multi-select (no tag) 67 + Reset Off and Recovery Time Multi-select (worst case) 67 + Reset Off and Recovery Time Antenna on 0.2 + Reset Recovery Time Antenna off 0.2 Port read 0.1 Port write 0.1 Read block 1.8 – 2.2 Write block 8.2 – 11 Reset 13.2 Select (locked tag) 5.4 – 22.8 + Reset Off and Recovery Time Select (no tag) 38 + 3x Reset Off and Recovery Time Select (worst case) 55 + 3x Reset Off and Recovery Time Common commands Cont. read (locked tag) ISO 14443 Type A only commands Increment value block 18.4 Decrement value block 18.4 Copy value block 18.5 Page 120 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Command tEXEC [ms] Read value block 2.3 Write value block 7.9 - 10.5 MIFARE® Login 4.9 Comments Power conditions Power on 79 Enable on 85 Does not include rise time of power supply Default Command Guard Time (20h = 1.2ms) was used. All timing data is advisory application information and does not form part of the specifications. It may change in future firmware releases. Please also note that all values specified in the above table depend on the tag used and Command Guard Time. November 4, 2008 Page 121 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 Appendix D - Version History 09/02/2005 09/06/2006 10/22/2008 Initial Release • Register default value changed for Selection Timeout ISO 14443 B • Support of asynchronous baud rates for the highspeed select command • Improved support of read / write operations for LRI tags • Added commands to read and write multiple blocks ('rd' / 'wd') • Flag added to disable read after write • Bug fixes • Extended ID supports the ISO 14443 A SAK byte • High Level support of the Innovision Jewel tag (selection, read and write operations) • Added functionality to switch between ReqA/B or WupA/B usage • The Quiet command now supports ISO 14443 part 3 and 4. • Improved ISO 14443 4 handling • Changed LED behavior in continuous read mode and multilist • Increased LED flash duration time • New command "ox" added to reread all register settings • Basic Paypass 1.0 functionality • Improved SAM handling & support for new NXP SAM. Page 122 of 125 Version 1.0, Rev. 1.0 Version 1.1, Rev. 1.0 Version 1.2, Rev. 1.0 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 Appendix E - Approvals / Certificates CE Declaration HID Global declares that, in conformity with the European CE requirements specified in the EMC Directive 89/336/EEC, the HID HF Multi ISO Plug & Play Modules, the HID HF Multi ISO Desktop Reader and the Plug-In Reader Module, described in this manual, are CE compliant The relevant documents are available. If any of the Multi ISO Plug & Play Modules or the CF Card Reader Module is operated from a mains power supply, all power connections and additional components of the final device must also comply with the EMC Directive 89/336/EEC directive. Customers selling into Europe must themselves make sure that the final device conforms to the EMC Directive 89/336/EEC directive. The compliance of important international regulations into business practices are a priority and the implementation of the EMC Directive 89/336/EEC is fully in line with the company’s commitment to continuously improve its Quality Management System. November 4, 2008 Page 123 of 125 © 2008 HID Global Corporation. All rights reserved. 1508-USM-00-0-02 HF Multi ISO RFID Reader User Manual, Firmware V1.2 FCC Declaration HID Global declares that, in conformity with the U.S. Directive FCC part 15, HID HF Multi ISO Plug & Play Modules, the HID HF Multi ISO Desktop Reader and the Plug-In Reader Module, described in this manual, are FCC part15 compliant The relevant documents are available. If any of the Multi ISO Plug & Play Modules or the CF Card Reader Module is operated from a mains power supply, all power connections and additional components of the final device must also comply with the US FCC Part 15 directive. Customers selling into the USA must themselves make sure that the final device conforms to the US FCC Part 15 directive. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For HID Identification Technologies GmbH, the compliance of important international regulations into business practices are a priority and the implementation of the FCC part 15 is fully in line with the company’s commitment to continuously improve its Quality Management System. Page 124 of 125 November 4, 2008 © 2008 HID Global Corporation. All rights reserved. HF Multi ISO RFID Reader 1508-USM-00-0-02 User Manual, Firmware V1.2 RoHS Compliance HID Global declares that, in conformity with the Directive 2002/95/EC about the Restriction of Hazardous Substances (RoHS), its HID HF Multi ISO RFID Reader products, listed in this manual, are RoHS compliant The following substances are contained in accordance with the limits required by the Directive. Cadmium and cadmium compounds Lead and lead compounds Mercury and mercury compounds Hexavalent chromium compounds Polybrominated biphenyls (PBB) Polybrominated Diphenylethers (BPDE) For HID Global, the integration of environmental considerations into business practices is a priority and the implementation of RoHS Directive is fully in line with the company’s commitment to continuously improve its Quality Management System. November 4, 2008 Page 125 of 125 © 2008 HID Global Corporation. All rights reserved.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Creator Tool : Acrobat PDFMaker 8.1 for Word Modify Date : 2009:10:12 18:02:46+02:00 Create Date : 2008:11:04 09:15:46-07:00 Metadata Date : 2009:10:12 18:02:46+02:00 Producer : Acrobat Distiller 8.1.0 (Windows) Format : application/pdf Creator : Laurie Hanna Title : OMNIKEY HF Multi ISO RFID Reader Description : User Manual Document ID : uuid:b2b28704-c93e-497e-b0bc-7c0f726ef0c5 Instance ID : uuid:652b3325-e8f9-4ee0-9f31-0195aeb51a3b Company : HID Part : 1 Conformance : B Page Count : 125 Page Layout : SinglePage Subject : User Manual Author : Laurie HannaEXIF Metadata provided by EXIF.tools