Pelco CCC1390H C2924M QS User Manual To The 2b5743b6 4fb5 4c45 B75f 7427bce0787d
User Manual: Pelco CCC1390H to the manual
Open the PDF directly: View PDF .
Page Count: 2
Download | |
Open PDF In Browser | View PDF |
C2924M-QS.fm Page 1 Wednesday, April 27, 2005 3:26 PM C2924M-QS (4/05) CCC1390H Series Camera Quick Start Guide SETUP MENUS Use the setup menus to customize the camera settings. Refer to the setup menus as shown on this and the opposite page. This quick start guide describes how to install and configure the CCC1390H Series camera in most applications. It contains a representation of the setup menus to help you locate and change specific settings. Refer to the enclosed CD for the following documentation: • • • V-PHASE ADJ LINE SYNC MAIN MENU Installation/Operation manual: INSTALL.PDF Quick Start Guide: QSG.PDF Important Safety Instructions: SAFETY.PDF MODELS PROFILES EXPOSURE SETTINGS FUNCTION SETTINGS CAMERA SETUP AI AUTO ADJUSTMENT PIXEL CORRECTION SYSTEM INFORMATION CAMERA SETUP > > > > > > > ADDRESS COM SPEED LED SWITCH >1 > 4800 > ON > ON EXIT BACK EXIT CCC1390H-6 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, NTSC format CCC1390H-6X 1/3-inch high resolution day/night, WDR, CCD camera, 24 VAC or 12 VDC, PAL format > AUTO > BACK EXIT MANUAL RED/BLUE > STANDARD > CUSTOM STANDARD OK > -1 > -2 >1 >1 BACK EXIT PIXEL CORRECTION BACK EXIT APERTURE GAIN > -1 BACK EXIT CANCEL E-ZOOM 3a PHASE VALUE = 45 SHARPNESS RED GAIN BLUE GAIN RED HUE BLUE HUE AI AUTO ADJUSTMENT PROFILES ACTIVE SAVE AS *DEFAULT LINE SYNC V-PHASE ADJ POSITION ZOOM POSITION > OFF > BACK EXIT COVER THE LENS AND SELECT OK OK CANCEL EXPOSURE SETTINGS AUTO EXPOSURE VIDEO LEVEL FLICKERLESS AGC DSS(SENS) DAY & NIGHT D&N DETECTION D&N FILTER LIMIT BACK > NORMAL >0 > OFF > ON >4 > COLOR > > EXIT Lens Mount Back Focus Locking Screw Camera Mount and 3a Adapter Serial Terminating Switch Auto Iris Lens Connector Video Output Connector Setup Button Power Terminal Strip Indicators FIRMWARE VERSION OSD VERSION 1.0 1.0 RESTORE FACTORY SETTINGS > BACK EXIT MASK SETTING MASK MASK EDIT MASK ERASE > OFF > BACK EXIT EDIT TITLE TITLE RESTORE FACTORY SETTINGS FUNCTION SETTINGS MASKING SYSTEM INFORMATION LINE SYNC WHITE BALANCE MANUAL RED/BLUE GAMMA SHARPNESS E-ZOOM MASKING TITLE BACK > > AUTO > > 60%(NORM) > > > > EXIT OK TITLE EDIT TITLE > OFF > BACK EXIT CANCEL ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz 0123456789-/ BACK ________________ BS C2924M-QS.fm Page 2 Wednesday, April 27, 2005 3:26 PM LENS The CCC1390H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. It automatically senses an auto iris lens as soon as you plug in the connector. The camera has a standard CS-mount that can accept a C-mount lens with a PCMA40 lens adapter. To mount the lens onto the camera: 1. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign matter between the lens and the camera imager. 2. C-mount lens: Screw the adapter onto the lens. 3. Screw the lens onto the lens mount. 4. DC-drive auto iris lens: Connect the four-pin connector from the lens to the connector on the back of the camera. MOUNT The CCC1390H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use a standard 1/4-20 screw. The maximum thread depth (top) is 0.188 inches (4.7 mm). To extend the thread depth (top) to 0.25 inches (6.4 mm), use the camera mount spacer (supplied). The maximum thread depth (bottom) is 0.25 inches (6.4 mm). ELECTRICAL Power Connect 12 VDC or 24 VAC power to the three-pin terminal strip on the back of the camera. Use a Class 2 isolated power source for the CCC1390H camera that can supply 12 VDC ±15% or 24 VAC ±15%, 50/60 Hz. Maximum power consumption is about 3.5 watts. Video Connect a coaxial video cable to the BNC connector on the back of the camera. External Control For serial control, install the control connector (refer to Connecting External Control in the Installation/ Operation manual for more information). NOTE: After you customize any aspect of the CCC1390H Series camera, be sure to save your custom settings. (Refer to Profiles in the Installation/Operation manual for information about saving custom settings.) BUTTON ACTION Enter setup menus. Long center press Move up or down in menu or item options. Up or down press Move right or left in menu. Right or left press Select menu or item. Short center press Save setting and exit to menu. Short center press Adjust the back focus: LENS FOCUS (1) Use a 1.5-mm Allen wrench to loosen the back focus locking screw. After mounting the lens, you must focus your CCC1390H Series camera. You will adjust both the back focus (on the camera) and the fine focus (on the lens). (2) Turn the lens until the image is focused. (3) Tighten the back focus locking screw clockwise. NOTE: The back focus has already been adjusted using a standard CS-mount lens. However, you might need to adjust it again to match the mounted lens. 1. Auto iris only: Cover the auto iris lens with a suitable neutral density (ND) filter. This opens the iris fully. For best results, use an ND3 filter. 2. Manual iris only: Open the iris completely. The figure shows the manual iris, varifocal, and lens focus locking screws for a sample lens. Refer to your lens documentation for more information. a. Display the EXPOSURE SETTINGS menu. 8. Tighten all lens locking screws. NOTE: When tightening the lens locking screws, do not over-turn or force any screw. 9. Auto iris only: Remove the ND filter. 10. If necessary, disable AGC: LENS FOCUS LOCKING SCREW VARIFOCAL b. c. 1.5 MM ALLEN WRENCH Change AGC to ON. LOCKING SCREW Select EXIT to save the AGC setting. 4. Aim the camera at the farthest object in the field of view. Make sure it is at least 6.5 ft (2 m) away. 5. Fixed focal length lens only: a. WARNING: Do not over-tighten the back focus locking screw because you may damage the camera. Back focus is a coarse adjustment. You will make the fine focus adjustment in steps c and d. c. Move the varifocal locking screw up or down to set the field of view. d. Adjust the lens focus to achieve the best fine focus. e. Repeat steps c and d until the focus is correct. 7. Manual iris only: Adjust the iris for the best picture quality. The largest aperture gives the best light sensitivity; the smallest aperture gives the greatest depth of field. MANUAL IRIS LOCKING SCREW 3. If necessary, enable Automatic Gain Control (AGC) on the EXPOSURE SETTINGS menu. AGC is enabled by default. Use the five-position button on the rear panel to access and navigate the setup menus. The following table lists the button presses for each menu action. MENU ACTION Set the varifocal to wide (W) and the lens focal length to far (∞). a. b. b. ACCESSING THE SETUP MENUS 6. Varifocal lens only: Set the lens focal length to far (∞). a. Display the EXPOSURE SETTINGS menu. b. Change AGC to OFF. c. Select EXIT to save the AGC setting. 11. Auto iris only: Perform the auto iris lens adjustment procedure (refer to Auto Iris Lens Adjustment in the Installation/Operation manual for more information). 12. As soon as you finish customizing this and all other camera settings, save your custom settings into the CUSTOM profile. This protects them in case the camera loses power or must be restarted (refer to Profiles in the Installation/Operation manual for more information). Adjust the back focus: (1) Use a 1.5-mm Allen wrench to loosen the back focus locking screw. (2) Turn the lens until the image is focused. (3) Tighten the back focus locking screw clockwise. WARNING: Do not over-tighten the back focus locking screw because you may damage the camera. REVISION HISTORY Manual # C2924M-QS Date 4/05 Comments Original version. Pelco and the Pelco logo are registered trademarks of Pelco. c. Back focus is a coarse adjustment. You will make the fine focus adjustment in the next step. Adjust the lens focus to achieve the best fine focus. ©Copyright 2005, Pelco. All rights reserved. Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150 International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120 C2924M-QS (4/05)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Modify Date : 2005:04:27 15:32:57-07:00 Create Date : 2004:07:20 17:06:37Z Page Count : 2 Creation Date : 2004:07:20 17:06:37Z Mod Date : 2005:04:27 15:32:57-07:00 Producer : Acrobat Distiller 5.00 for Macintosh Author : Metadata Date : 2005:04:27 15:32:57-07:00 Creator : Title : C2924M-QS.fm Page Mode : UseNoneEXIF Metadata provided by EXIF.tools