Philio Technology PAD02 Smart Dimmer Socket User Manual

Philio Technology Corporation Smart Dimmer Socket

User manual

PAD02 Z-Wave Smart Dimmer Socket Warning: Do not use Non-Dimmable LED lamps.PAD02 is an E27(EU)/ E26(US) Edison screw based lamp socket, which provides electrical connection to the E14(EU)/ E12(US) Edison screw based lamps and support it in the lighting fixture. The use of socket allows lamps to be safely and conveniently replaced. You can On/Off the light by pressing the button briefly, or a long pressing to control the brightness of dimmable light bulb.This dimmer is a transceiver which is a security enabled device which based on Z-Wave Plus technology, and it is fully compatible with any Z-WaveTM enabled network. Since PAD02 supports Security Command Class, it can learn with Secured controller. Its functionality and supported command classes is identical when included as a secure and non-secure device.Adding to Z-WaveTM NetworkIn the front casing, there is an on/off button with LED indicator below which is used toswitch on and off or carries out inclusion, exclusion, reset or association.When first power applied, its LED flashes on and off alternately and repeatedly at 0.5second intervals. It implies that it has not been assigned a node ID and start autoinclusion.Auto InclusionThe function of auto inclusion will be executed as long as the dimmer does nothave Node ID and just connect the switch to main power.Note: Auto inclusion timeout is 2 minute during which the node information ofexplorer frame will be emitted once every several seconds. Unlike “inclusion” functionas shown in the table below, the execution of auto inclusion is free from pressing theOn/Off button on the dimmer.The table below lists an operation summary of basic Z-Wave functions. Please referto the instructions for your Z-WaveTM Certificated Primary Controller to access theSetup function, and to include/exclude/associate devicesFunction Description AnnotationNo node ID The Z-Wave Controller does not allocatea node ID to the Switch.LED 2-second on, 2-second offInclusion 1. Put your Z-Wave controller intoinclusion mode by following theinstructions provided by thecontroller manufacturer.One press one flash LED2. Pressing Include button of PAD02 three times within 2 seconds will enter inclusion mode.1
Exclusion 1. Put your Z-Wave controller intoexclusion mode by following theinstructions provided by thecontroller manufacturer.One press one flash LED2. Pressing Include button of PAD02 three times within 2 seconds will enter exclusion mode.3. Node ID has been excluded. 0.5s On, 0.5s Off (Enterauto inclusion)Reset 1. Pressing Include button of PAD02 three times within 2 seconds will enter inclusion mode.Use this procedure only inthe event that the primarycontroller is lost orotherwise inoperable.2. Within 1 second, press Include buttonof PAD02 again for 5 seconds.3. IDs are excluded. 0.5s On, 0.5s Off (Enterauto inclusion)Association 1. The PAD02 is an always listeningZ-Wave device, so associations may be added or removed by a con-troller at any time.Or If your controller requires to havethe PAD02 send a 'node informationframe' or NIF for associations, thenpressing the On/Off button threetimes within 2 seconds will causethe PAD02 to send its NIF.2. There are only one group for the switchIncluding a node ID allocated by Z-Wave Controller means inclusion. Excluding a nodeID allocated by Z-Wave Controller means exclusion.Failed or success in including/excluding the node ID can be viewed from the Z-Wave Controller. LED IndicationTo distinguish what mode the switch is in, view from the LED for identification.State Type LED IndicationNormal Whenever we switch On and off of the PAD02 by On/Off button or RF command, the LED will lights up when switch on; whereas LED off when switch off.No node ID Under normal operation, when the Switch has not been allocated a node ID, the LED flashes on and off alternately at 2-second intervals.By pressing On/Off button, it will stop flashing temporarily.Learning When PAD02 is in learning mode, LED flashes on and off alternately and repeatedly at 0.5 second intervals.Choosing a Suitable Location1. Do not locate the dimmer facing direct sunlight, humid or dusty place.2. The suitable ambient temperature for the Switch is 0°C~40°C.2
3. Do not locate the dimmer where exists combustible substances or any source of heat, e.g. fires, radiators, boiler etc.4. After putting it into use, the body of dimmer will become a little bit hot of which phenomenon is normal.screw lamp holder Type:Since the socket type for each country in Europe varies, refer to the outline for each socket suited for each country as follows: EU TYPE: PAD02-1 US TYPE: PAD02-2Note: Please make sure that the intensity of the screw lampholder of the electrical device must be Maximum Load (Watts) and have same head as the enclosed screw lampholder before inserting to the socket. 3
Troubleshooting Symptom Cause of Failure RecommendationThe Switch not working and LED off4. The Switch is not plugged into the electrical outlet properly5. The Switch break down1. Check power connections2. Don’t open up the Switch and send it for repair.The Switch LED illuminating, but cannot control the ON/OFFSwitch of the load attached1.Check if the load plugged into the Switch has its own ON/OFF switch2. The switch is protected1. Set the ON/OFF switch of the load attached to ON2. Unprotected the switch or follow the instruction of protection.The Switch LED illuminating, but the Detector cannot controlthe Switch1. Not carry out association2. Same frequency interference1. Carry out association2. Wait for a while to re-trySpecificationOperating Voltage 100V~240V / 50Hz~60HzMaximum Load (watts) 40W (Incandescent bulbs); ( PAD02-1; PAD02-2)Maximum Load (watts) 13W (Dimmable LED bulbs); ( PAD02-1; PAD02-2)Screw lamp holder Type: EU type: E27 to E14; PAD02-1 US type: E26 to E12; PAD02-2Operating Temperature 0°C ~ 40°CFrequency Range 868.40MHz & 869.85MHz/ EU (PAD02-1); 908.4MHz & 916.0MHz/ USA (PAD02-2);RF Maximum Power +5dBm Transmission Range Minimum 40 m in door 100m outdoor line of sightModulation Type FSK (Frequency-Shift Keying)** Specifications are subject to change and improvement without notice. FCC ID : RHHPAD02Warning: Do not use Non-Dimmable LED lamps.Warning:1.Plug out to disconnect from power supply; Do not plug in line. 2. Do not exceed the max rating.3. Do not use Non-Dimmable LED lamps.4
Disposal This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.Company of License Holder：Philio Technology CorporationAddress of License Holder：8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City24257, Taiwan(R.O.C) FCC Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital de-vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to cor-rect the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter.5

Navigation menu