Philio Technology PAN08 In Wall Switch User Manual BH002 RF ON OFF CONTROLLER
Philio Technology Corporation In Wall Switch BH002 RF ON OFF CONTROLLER
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2023419 |
| Application ID | jUCbKjd2/LYGv0BhD4a2OA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 50.1kB (626300 bits) |
| Date Submitted | 2013-07-23 00:00:00 |
| Date Available | 2013-07-25 00:00:00 |
| Creation Date | 2013-05-30 16:03:35 |
| Producing Software | LibreOffice 4.0 |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | BH002 RF ON/OFF CONTROLLER |
| Document Creator | Writer |
| Document Author: | . |
PAN08-1/-2/-3 Roller shutter controller connected to this Roller Controller. This in-wall Roller Shutter Controller is a transceiver which is a Z-WaveTM enabled device and is fully compatible with any Z-WaveTM enabled network. Slim design let the Controller can easily hide itself into the wall box and that will be good for the house decoration. The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of Roller Shutter. This in-wall Roller Shutter Controller is able to detect position of the Shutter by using the patterned power measuring method, so it can be remote controlled not only fully up or down , but also can be adjusted to ex. 30% or 50%. And when manual controlled by push button, the controller also can memorize the position and send the new shutter position to its controller (ex. IP-Gateway). Adding to Z-WaveTM Network In the front casing, there is an include button with LED indicator below which is used to carry out inclusion, exclusion, reset or association. When first power is applied, its LED flashes on and off alternately and repeatedly at 2-second intervals. It implies that it has not been assigned a node ID and cannot work with Z-Wave enabled devices. Auto Inclusion Fig 1. Assembling The function of auto inclusion will be executed as long as the PAN08 does not have Node ID and just connect the PAN08 to main power. The in-wall Roller Shutter Controller is designed to switch rise/lower roller shutter connected to its terminals using radio waves, controllers and a push button directly Note: Auto inclusion timeout is 4 minute during which the node information of explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as button again for 5 seconds until LED shown in the table below, the execution of auto inclusion is free from pressing the is off. Include button on the PAN08. Association 3. IDs are excluded. 2-second on, 2-second off 1. Have Z-Wave Controller entered One press one flash association mode. The table below lists an operation summary of basic Z-Wave functions. Please refer Or Pressing Include button three times to the instructions for your Z-WaveTM Certificated Primary Controller to access the within 1.5 seconds will enter Setup function, and to include/exclude/associate devices association mode 2. There are 1 group (Group 1) for the Function Description LED Indication No node ID The Z-Wave Controller does not allocate 2-second on, 2-second off PAN08 ※Including a node ID allocated by Z-Wave Controller means inclusion. a node ID to the PAN08. Inclusion 1. Have Z-Wave Controller entered Excluding a node ID allocated by Z-Wave Controller means exclusion. One press one flash ※Failed or success in including/excluding the node ID can be viewed from the Z-Wave inclusion mode. Controller. 2. Pressing Include button three times within 1.5 seconds will enter inclusion mode. Exclusion 1. Have Z-Wave Controller entered LED Indication One press one flash To distinguish what mode the PAN08 is in, view from the LED for identification. exclusion mode. 2. Pressing Include button three times within 1.5 seconds will enter exclusion mode. Reset 1. Node ID has been excluded. 2-second on, 2-second off Pressing Include button three times One press one flash LED Indication Motor No matter up or down, close or open, Led will flash every second activate while Motor activate. No node ID Under normal operation, when the PAN08 has not been allocated a node ID, the LED flashes on and off alternately at 2-second within 1.5 seconds will enter intervals. By pressing S1 S2 or Include button, it will stop flashing inclusion mode. 2. State Type temporarily. However, after disconnect and reconnect the PAN08, Within 1 second, press Include the LED will flash on and off alternately at 2-second intervals. Overload When overload state occurs, the PAN08 is disabled of which LED flashes on and off alternately at 0.5 second intervals. Overload state can be cleared by disconnect and reconnect the PAN08 to the main power Choosing a Suitable Location 1. Do not locate the PAN08 facing direct sunlight, humid or dusty place. 2. The suitable ambient temperature for the PAN08 is 0°C~40°C. 1. put the in wall PAN08 into a wall box and connect the AC power wire L,N to 3. Do not locate the PAN08 where exists combustible substances or any source of PAN08 connector L, N. heat, e.g. fires, radiators, boiler etc. 4. After putting it into use, the body of PAN08 will become a little bit hot of which 2. Connect the wall switch to the PAN08 as Fig1 . phenomenon is normal. Installation and operation 3. It is important to carry out a shutter calibration process before you control the shutter to move. Press inclusion button over 3 seconds and release before the 6th second, the roller shutter controller will start the shutter calibration process. The process is composed of three continue stages. The shutter move to the TOP in first stage, and move to the BOTTOM in second stage, and move to the TOP again in third stage. Then PAN08 will know the total range of UP and DOWN. 4. During the shutter calibration process, any emergencies happen you can press and release the include button to stop the process 5. If user found the direction is reverse, this may because the wrong connection of NC and NO to the motor, please change NC and NO connection and execute calibration process again. 6. To manually switch up and down of the shutter, simply press S1 or S2 . Basic Report Command： [Command Class Basic, Basic Report, Value = 0x00 (BOTTOM)] 7. PAN08 built in meter function and can read the Watt , KWh, V(Voltage), I(Current) , PF(Power Factor) of the load by using Z-Wave command class, user [Command Class Basic, Basic Report, Value = 0x01~0x62 (Between BOT- can set a threshold watt to get the warning caused by abnormal operation TOM and TOP)] [Command Class Basic, Basic Report, Value = 0xFE (UNKNOWN)] 8. PAN08 have overload protection function, and can help to prevent short circuit [Command Class Basic, Basic Report, Value = 0x63/0xFF (TOP)] caused by load. 1-2 BASIC_SET Programming PAN08 can only accept Basic Set Command which value is either (0x00)Bottom or 1. Basic Command Class Top (0x63/0xFF)，other value is not acceptable The PAN08 will respond to BASIC and BINARY commands that are part of the Z-Wave system. 1.1 BASIC_GET [Command Class Basic, Basic Set, Value = 0x63 或 0xFF] control the When PAN08 receive Basic Set Command，it will send Basic Report Command shutter to the top (0xFF)。 to report the position of the curtain。When the report value is 0x00, that mean the Shutter is bottom down, if the report value is 0xFF or 0x63 that mean the Shutter is at the top, any other value between0x01~0x62 imply Shutter at 1%~99% [Command Class Basic, Basic Set, Value = 0x00(0)] control the shutter to position；But if report value is 0xFE means the position is unknown。 the bottom(0x00)。 2 Binary Basic Get Command: [Command Class Basic, Basic Get] Switch Command Class 2-1 BINARY_SWITCH_GET, PAN08 can only accept Multilevel Switch Set Command which value is either When PAN08 receive Binary Switch Get Command, it will send Binary Switch Report (0x00)Bottom or Top (0x63 or 0xFF)，other value is not acceptable。 Command to report the position of the curtain. When the report value is 0x00, that mean the Shutter is bottom down, if the report value is 0xFF that mean the Shutter is [Command Class Multilevel Switch, Multilevel Switch Set, Value = 0x63 or at the top. But if report value is 0xFE means the position is unknown. 0xFF(255)] control the shutter to the top (0xFF)。 [Command Class Multilevel Switch, Multilevel Switch Set, Value = 0x00(0)] control Binary Switch Get Command： the shutter to the bottom(0x00)。 [Command Class Binary Switch, Binary Switch Get] Binary Switch Report Command： 3-2 MULTILEVEL SWITCH GET: [Command Class Binary Switch, Binary Switch Report, Value = 0x00(BOTTOM)] When PAN08 receive Multilevel Switch Get Command, it will send Multilevel Switch [Command Class Binary Switch, Binary Switch Report, Value = 0xFE(UNKNOWN)] Report Command to report the position of the shutter. When the report value is 0x00, [Command Class Binary Switch, Binary Switch Report, Value = 0xFF(TOP)] that mean the shutter is bottom down, if the report value is 0xFF or 0x63 that mean the shutter is at the top, any other value between0x01~0x62 imply shutter at 2-2 BINARY_SWITCH_SET 1%~99% position；But if report value is 0xFE means the position is unknown. PAN08 can only accept Binary Switch Set Command which value is either (0x00) Bottom or Top (0xFF)，other value is not acceptable。 Switch Multilevel Get Command： [Command Class Multilevel Switch, Multilevel Switch Get] [Command Class Binary Switch, Binary Switch Set, Value = 0xFF(255)] Multilevel Switch Report Comman： control the shutter to the top (0xFF)。But if the shutter is on the way down, this command will stop the shutter。 [Command Class Multilevel Switch, Multilevel Switch Report, [Command Class Binary Switch, Binary Switch Set, Value = 0x00(0)] Value = 0x00(BOTTOM)] control the shutter to the bottom(0x00)。But if the shutter is on the way up, this command will stop the shutter。 [Command Class Multilevel Switch, Multilevel Switch Report, Value = 0x01~0x62(Between BOTTOM and TOP)] 3. Multilevel Switch Command Class (Version 3)： [Command Class Multilevel Switch, Multilevel Switch Report, 3-1 MULTILEVEL SWITCH SET: Example 1：If user want shutter move up , and the distance is 60% of total Value = 0xFE(UNKNOWN)] range(assume the now Step_Size= 50) [Command Class Multilevel Switch, Multilevel Switch Report, Command Class Multilevel Switch Value = 0x63/0xFF(TOP)] Multilevel Switch Start Level Change 3-3 MULTILEVEL SWITCH START LEVEL CHANGE: Up/Down = 0x00 (UP = 0x00) This is the command which user can move the shutter to the particular position ex. 60% of total range [Command Class Multilevel Switch, Multilevel Switch Start Level Change, Inc/Dec = 0x00 (Increment = 0x00：Step_Size = 50+10 = 60) Step_Size = 10 This value represent how many the new step_size want to increase or decrease Up/Down Value , Inc/Dec Value, Step Size Value]。 3-3.1 Up/Down Bit : Example 2： If user want shutter move down , and the distance is 50% of total If Up/Down Bit=0x00 Shutter move up； range(assume the now Step_Size= 50) If Up/Down Bit=0x01 Shutter move down； Command Class Multilevel Switch If Up/Down Bit=0x03 no move Multilevel Switch Start Level Change 3-3.2 Inc/Dec Bit： Up/Down = 0x01 If Inc/Dec Bit=0x00 means New Step_Size = Now Step_Size + Step_Size ； Inc/Dec = 0x03 If Inc/Dec Bit=0x01 means New Step_Size = Now Step_Size - Step_Size ； (Down = 0x01) (No Inc/Dec = 0x03：not change Step_Size value，Step_Size = 50) If Inc/Dec Bit=0x03 means New Step_Size = Now Step_Size Step_Size = 0 This value represent how many the new 3-3.3 Step_Size： step_size want to increase or decrease, Range from 0x00~0x63 or 0xFF, default value=50, and the meaning of 0x63 and when Inc/Dec = 0x03 please set this value to 0xFF is 100% of total range. If the Now Step_Size + Step_Size >100, the new 0) Step_Size will stay at 100 , if the Now Step_Size - Step_Size <0 , the New Step_Size will stay at 0 Example 3：If User not go to change shutter position but only change Multilevel Switch Report： Step_Size to 40%( assume the now Step_Size= 50) Ex. Report position at 30% Command Class Multilevel Switch [Command Class Multilevel Switch， Multilevel Switch Report，Value = 30(%)] Multilevel Switch Start Level Change Up/Down = 0x03 Inc/Dec = 0x01 4-2 Meter Command Class： The Switch will report its (1) instant Power Consumption (Watt) or (2) accumulated (No Up/Down motion = 0x03) power consumption(KWH) or (3) AC load Voltage (V) or (4) AC load current ( I ) (Decrement = 0x01：Step_Size = 50–10 = (5) load power factor (PF) 40) Step_Size = 10 to Z-Wave Controller after receive the Meter Get Command from Z-Wave Controller. This value represent how many the new step_size want to increase or decrease When the power consumption of load vary over 5%, it will send Meter report to the nodes of Group as well ATT.1. Ignore_Start_Level、Start_Level、Dimming_Duration can not be used 4-2.1 Instant Power Consumption (Watt) of Switch 2. PAN08 can not control the speed of motor。 When receiving Meter Get Command, it will report Meter Report Command to the 3-3.4 MULTILEVEL SWITCH STOP LEVEL CHANGE: node asked. When receive Multilevel Switch Stop Level change Command PAN08 will stop the Meter Get Command: [Command Class Meter, Meter Get, Scale =0x02(W)] motor。 Z-wave’s Groups introduction (Association Command Class Version 1 ) Meter Report Command: [Command Class Meter，Meter Report，scale(bit There is only one group called Group1，there is only one node for Group1 which 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter support MULTILEVEL_SWITCH_REPORT、METER_REPORT_COMMAND_V3、 Value 1，Meter Value 2，Meter Value 3，Meter Value 4] ALARM_REPORT。 4-1 Report the shutter position ： Rate Type = 0x01 Every time when user press S1 or S2 and let shutter to move, PAN08 will report the Meter Type = 0x01 position status to controller, and at the moving process when change over 10% Precision = 1 PAN08 will send Multilevel Switch Report to Group 1 also. Scale = 0x02(W) Size = 4 Bytes (Meter Value) Meter Value 1 = (W) MSB Meter Value 2 = (W) Size = 4 bytes (Meter Value) Meter Value 3 = (W) Meter Value 1 = (KWh) MSB Meter Value 4 = (W)LSB Meter Value 2 = (KWh) Meter Value 3 = (KWh) Example: Meter Value 4 = (KWh) LSB Meter Value 1 = 0x00 (W) Meter Value 2 = 0x00 (W) Example: Meter Value 3 = 0x03 (W) Scale = 0x00 (KWh) Meter Value 4 = 0xEA (W) Precision = 2 Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W Size = 4 Bytes (KW/h) Meter Value 1 = 0x00(KWh) 4-2.2 Accumulated Power Consumption (KW/h) Meter Value 2 = 0x01(KWh) When receiving Meter Get Command, it will report Meter Report Command to Meter Value 3 = 0x38(KWh) the node asked. Meter Value 4 = 0xA3(KWh) Accumulated power consumption (KW/h) = (Meter Value 2*65536) + (Meter Value Meter Get Command: [Command Class Meter, Meter Get, Scale = 0x00 3*256) + (Meter Value 4) = 800.35 (KW/h) KW/h)] Meter Report Command: [Command Class Meter，Meter Report，scale(bit 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter Value 1，Meter Value 2，Meter Value 3，Meter Value 4] 4-2.3 AC load Voltage (V) When receiving Meter Get Command, it will report Meter Report Command to the node asked. Meter Get Command: [Command Class Meter, Meter Get, Scale =0x04(V)] Rate Type = 0x01 Meter Type = 0x01 Meter Report Command: [Command Class Meter，Meter Report，scale(bit 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter Value 1，Meter Value 2] Precision = 2 Scale = 0x00 (KWh) Meter Report Command: [Command Class Meter，Meter Report，scale(bit 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter Value 1，Meter Value 2] Rate Type = 0x01 Meter Type = 0x01 Precision = 1 Scale = 0x04(V) Size = 2 Bytes (Meter Value) Rate Type = 0x01 Meter Value 1 = High Byte (V) Meter Type = 0x01 Meter Value 2 = Low Byte (V) Precision = 2 Scale = 0x05(I) Example: Size = 2 Bytes (Meter Value) Scale = 0x04 (V) Meter Value 1 = High Byte (I) Precision = 1 Meter Value 2 = Low Byte (I) Size = 2 (2 Bytes of V) Meter Value 1 = 0x09(V) Example: Meter Value 2 = 0x01(V) Scale = 0x05 (I) AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V) Precision = 2 Size = 2 (2 Bytes of I) 4-2.4 AC load current ( I ) Meter Value 1 = 0x01(I) When receiving Meter Get Command, it will report Meter Report Command to the Meter Value 2 = 0x21(I) node asked. AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A) 4-2.5 load power factor (PF) When receiving Meter Get Command, it will report Meter Report Command to the node asked. Meter Get Command: [Command Class Meter, Meter Get, Scale =0x05(I)] Meter Get Command: [Command Class Meter, Meter Get, Scale =0x06(PF)] 4-3 Alarm Report Command： Meter Report Command: [Command Class Meter，Meter Report，scale(bit 2) +Rate Type +Meter Type，Precision + Scale(bit 1,0)+ Size，Meter Value 1] When PAN08 detect Overload，it will send Alarm_Report to Group1，Alarm Level=0xFF。When receive Alarm_Get command and the PAN08 not in overload status , it will send Alarm_Report，Alarm Level=0x00。 Rate Type = 0x01 4-3.1 Alarm Report： Meter Type = 0x01 [Command_Class_Alarm, Alarm_Report, Alarm Type = 0x08, Alarm Level = 0xFF Precision = 2 (Overload)] Scale = 0x06(PF) Size = 1 Bytes [Command_Class_Alarm, Alarm_Report, Alarm Type = 0x08, Alarm Level = 0x00 Meter Value 1 (Normal)] Example: Scale = 0x06 (PF) Precision = 2 Size = 1 (1 Byte of PF) Meter Value 1 = 0x63(PF) Load power factor (PF) = Meter Value 1 = 0.99 Z-Wave’s Configuration Configuration Function Parameter Size Value Unit Default Description 0x01- 5s 720 5*720s=3600s=1 (Byte) Watt 4-2.6 reset Accumulated Power Consumption (KWh) Meter This command is to reset the Accumulated Power Consumption (KWh) to 0 Report 0x7FFF hour Period Meter Reset Command： [Command Class Meter, Meter Reset] KWH Meter 10 0x010x7FFF 10min 6*10min= 1 hour 3 Report This is a warning when the wattage of load over the preset threshold value, If the Period setting value is 1100, when the load wattage over this value, PAN08 will send Watt Threshold 10-1100 1watt Meter Report command to the node of correspond Group. Default value=1100W 1100 of Watt 5-4 Threshold of KWh for Load Caution for Load This is a warning when the KWh of load over the preset threshold value, If the Caution Threshold setting value is 10000, when the Accumulated Power Consumption of Relay1 or 1-10000 1KWh Relay2 over this value, PAN08 will send KWh Meter Report command to the node of 10000 correspond Guoup, minimum value is 1KWh and default value is 10000 kWh of KWH for Load Caution 6. Command Classes The Switch supports Command Classes including… * COMMAND_CLASS_SWITCH_BINARY 5-1 Watt Meter Report Period: * COMMAND_CLASS_BASIC If the setting is configured for 1hour (set value =720), the PAN08 will report its instant power consumption every 1 hour to the node of correspond Group. The * COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 maximum interval to report its instant power consumption is 45 hours * COMMAND_CLASS_VERSION (5s*32767/3600=45hr). Default value is 1 hour * COMMAND_CLASS_ASSOCIATION * COMMAND_CLASS_METER_V3 * COMMAND_CLASS_CONFIGURATION 5-2 KWH Meter Report Period: If the setting is configured for 1hour (set value =6), the PAN08 will report its * COMMAND_CLASS_SWITCH_MULTILEVEL_V3 Accumulated Power Consumption (KW/h) every 1 hour to the node of correspond * COMMAND_CLASS_ALARM Group. The maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55 days). Default value=1 hour Troubleshooting 5-3 Threshold of Watt for Load Caution Symptom 11 Cause of Failure Recommendation The PAN08 not working and LED off 1. The PAN08 is not connect to the Main power 1. Check power connections Warning: 2. Don’t open up the PAN08 and 1.Plug out to disconnect from power supply; Do not plug in line. send it for repair. 2. Do not exceed the max rating 2. The PAN08 break Disposal down The shutter move direction Wrong connection of NC is reverse This marking indicates that this product should not be disposed with Swap the NC NO connection other household wastes throughout the EU. To prevent possible harm to and NO to the motor PAN08 LED light work fine 1. No association setting 2. Same frequency But can not control interference 1. Carry out association 2. Wait for a while to re-try the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and Specification collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Operating Voltage 100 ~240VAC Company of License Holder：Philio Technology Corporation Address of License Holder：8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist., New Taipei City 24257,Taiwan(R.O.C) Maximum Load Resistive load 1100W/600W/550W(EU/US/TW) max Range Minimum 30 m in door 100m outdoor line of sight FCC Interference Statement Operating Temperature 0°C ~ 40°C This equipment has been tested and found to comply with the limits for Frequency Range PAN08-1 868.42 (EU) / PAN08-2 908.42(USA/Canada) / PAN08-3 a Class B digital device, pursuant to Part 15 of the FCC Rules. These 922.5/923.9/926.3MHz (Taiwan/JP)MHz limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used ** Specifications are subject to change and improvement without notice. in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that FCC ID : RHHPAN08 interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which 12 can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 13
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 13 Language : zh-TW Title : BH002 RF ON/OFF CONTROLLER Author : . Creator : Writer Producer : LibreOffice 4.0 Create Date : 2013:05:30 16:03:35+08:00EXIF Metadata provided by EXIF.tools