Philips Electronics M105 15" Color LCD TV/Monitor User Manual Exhibit 6
Philips Electronics Industries (Taiwan) Ltd 15" Color LCD TV/Monitor Exhibit 6
User Manual
& . ' " - Product Features 150MT • Multi video input allowing display of PC, DVD, VCD, VCR and TV • Picture in Picture (PIP) function • Super-high brightness and fast response time • AUTO adjustment optimizes picture quality • 100-page Teletext (in areas where teletext service is available) RETURN TO TOP OF THE PAGE Technical Specifications* LCD PANEL • Type TFT LCD • Screen size 15" visual • Pixel Pitch 0.297 x 0.297mm (15.0") • LCD Panel type 1024 x 768 pixels R.G.B. vertical stripe Anti-glare polarizer hardness • Effective viewing area 304.1 x 228.1mm (15.0") • Display Colors 8 bits interface (16M colors) SCANNING • Vertical refresh rate 56Hz-76Hz • Horizontal frequency 30KHz-61KHz VIDEO • Video dot rate 80 MHz • Input impedance - Video 75 Ohm - Sync 2K Ohm • Input signal levels 700m Vpp • Sync input signal Separate sync Composite sync • Sync polarities Positive and negative • Input Frequency XGA Hsync 60 - 76 Hz (N.I.) SVGA Hsync 56 - 75 Hz (N.I.) VGA Hsync - 76 Hz (N.I.) • Video interface 48- 61 KHz, Vsync 35- 50 KHz, Vsync 31- 38 KHz, Vsync 60 D-sub, S-Video, TV-RF, SCART or composite and components video AUDIO • Input level for PC/SVHS/SCART 500 mV nominal • Headphone out signal level 4mW max. • Loudspeaker 2x2.5W OPTICAL CHARACTERISTICS • Contrast ratio 500 (typ.) • Brightness 300 cd/m (typ.) • Peak contrast angle 6 o'clock • White Chromacity x: 0.281 y: 0.311 (at 9300° K) x: 0.312 y: 0.338 (at 6500° K) • Viewing Angle (C/R >5) Upper >60° (typ.) Lower >70° (typ.) Left >75 ° (typ.) Right >75 ° (typ.) • Response time <=25ms (typ.) * These information are subject to change without notice. RETURN TO TOP OF THE PAGE Resolution & Preset Modes • Maximum 1024 x 768 at 75Hz • Recommended 1024 x 768 at 60Hz 14 user definable modes 14 factory preset modes: H. freq (KHz) Resolution V. freq (KHz) 31.469 640*350 70.086 31.469 720*400 70.087 31.469 640*480 59.940 35.000 640*480 67.000 37.861 640*480 72.809 37.500 640*480 75.000 35.156 800*600 56.250 37.879 800*600 60.317 48.077 800*600 72.188 46.875 800*600 75.000 49.700 832*624 75.000 48.363 1024*768 60.004 56.476 1024*768 70.069 60.023 1024*768 75.029 RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving features: Power Management Definition VESA H- V- Power LED Video Mode syncsync Usedcolor ON Active Yes Yes 48W Green Blinking Stand-by Blanked No Yes < 2W Green Blinking Suspend Blanked Yes No < 2W Green Blinking OFF Blanked No No < 2W Green ® ENERGY STAR compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this ® product meets the ENERGY STAR guidelines for energy This monitor is RETURN TO TOP OF THE PAGE efficiency. Physical Specifications • Dimension (WxHxD) 391 x 366 x 200 mm (incl. Pedestal) • Weight 5.1 Kg • Tilt (Forward / Backward) - 5° / 25° • Power supply 100 — 240 VAC, 50/60 Hz • Power consumption 48 W (typ.) • Temperature (operating) 5° C to 35° C • Relative humidity 20% to 80% • System MTBF 50K hrs (CCFL 40Khrs) * These information are subject to change without notice. RETURN TO TOP OF THE PAGE Pin Assignment The 15-pin D-sub connector (male) of the signal cable: Pin Pin Assignment Assignment No. No. 1 Red video input 9 DDC +5V 2 Green video input 10 Logic ground Identical output 3 Blue video input 11 connected to pin 10 Identical output 4 12 Serial data line (SDA) connected to pin 10 5 Cable detect 13 H. Sync / H+V 6 Red video ground 14 V. Sync 8 Green video ground Blue video ground Data clock line (SCL) 15 RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components. Front View Product Description RETURN TO TOP OF THE PAGE Physical Function Tilt Front View Product Description Activate PIP (Picture in Picture) window and select size 1 PIP 2 PCTV/Video TV/Video mode 3 VIDEO SOURCE 4 TV/Video source selection Power switch On/Off 5 Increase or decrease the channel number 6 Automatically adjust the H/V position, phase and clock setting 7 8 MENU OK Side View Increase or decrease the level of audio volume Open the OSD and select the highlighted function RETURN TO TOP OF THE PAGE Headphone Jack LINE OUT Jack RETURN TO TOP OF THE PAGE Rear View 1 DC 12V DC 12V power in 2 PC - Video D-Sub input 3 PC - Audio PC Stereo input 4 S-VIDEO (L) AV audio (L) S-VIDEO (R) AV audio (R) 5 S-VIDEO 6 S-VIDEO in EXTERNAL/ EURO-AV 7 75 SCART connection (for Europe only) TV Antenna or CATV cable in RETURN TO TOP OF THE PAGE Optimizing Performance • For best performance, ensure that your display settings are set at 1024x768@60Hz (for 15") or 1280x1024, 60Hz (for 18"). Note: You can check the current display settings by pressing the "OK" button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION. • You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performance out of your monitor, included in this CD. A step-by-step instructions is provided to guide you through the installtion process. Click on the link to know more about this program. More about FP_setup01.exe Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS. RETURN TO TOP OF THE PAGE
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2001:10:16 22:02:41-03:00 Create Date : 2001:10:16 22:02:16-03:00 Title : Exhibit 6. Author : PBE User Creator : Microsoft Word 9.0 Producer : Acrobat Distiller 4.0 for Windows Page Count : 10 Mod Date : 2001:10:16 22:02:41-03:00 Creation Date : 2001:10:16 22:02:16-03:00 Metadata Date : 2001:10:16 22:02:41-03:00EXIF Metadata provided by EXIF.tools