Philips Electronics M111 18 inches SXGA LCD all-in-one Monitor/TV User Manual

Download:
Mirror Download [FCC.gov]
Document ID	255392
Application ID	dXbsuvVbCtn1CiG4rDM3Eg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.1kB (163795 bits)
Date Submitted	2002-07-10 00:00:00
Date Available	2002-07-10 00:00:00
Creation Date	2002-07-09 18:29:01
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2002-07-09 18:29:13
Document Title	User Manual

Exhibit 3
Installstion and Operating Instructions
Product Information
Product Features • Technical Specifications • Resolution & Preset Modes •
Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification •
Pin Assignment • Product Views • Physical Function
Product Features
180MT
18 inch-SXGA LCD all-in-one Monitor/TV with excellent display performance
Multiple video input allowing display of PC, TV(with Teletext), DVD and VCD
Picture in Picture (PIP) function for displaying both TV or video and PC application on
the screen
Super-high brightness/contrast and fast response time
100-page Teletext (available only in Asia Pacific and Western Europe)
Digital Nicam/2CS stereo(available only in Asia Pacific and Western Europe)
Component Video Input (YPbPr/YCbCr) for DVD (available only in Asia Pacific and
NTSC systems)
Euroconnector (SCART) (available only in Western Europe)
RETURN TO TOP OF THE PAGE
Technical Specifications*
LCD PANEL
• Type
TFT LCD
• Screen size
18.1" visual
• Pixel Pitch
0.2805 x 0.2805mm
• LCD Panel type
1280 x 1024pixels
R.G.B. vertical stripe
Anti-glare polarizer
• Effective viewing area
(H) 359.0 x (V) 287.2mm
• Display Colors
8 bits interface (16.7M colors)
SCANNING
• Vertical refresh rate
56Hz-75Hz
• Horizontal frequency
30kHz-80kHz
VIDEO
• Video dot rate
135 MHz
• Input impedance
- Video
75 Ohm
- Sync
2K Ohm
• Input signal levels
0.7 Vpp
• Sync input signal
Separate sync
Composite sync
• Sync polarities
Positive and negative
• Input Frequency
SXGA Hsync
XGA Hsync
SVGA Hsync
VGA Hsync
• Video interface
D-sub, S-Video, TV-RF, SCART (Europe) or composite
and components video (others)
64- 80 kHz, Vsync 60 - 75 Hz (N.I.)
48- 61 kHz, Vsync 60 - 75 Hz (N.I.)
35- 50 kHz, Vsync 56 - 75 Hz (N.I.)
31- 38 kHz, Vsync 60 - 75 Hz (N.I.)
AUDIO
• Input level for
PC/SVHS/SCART
500 mV nominal
• Headphone out signal level
4mW max.
• Loudspeaker
5W Stereo Audio (2.5W/channel RMS x2, 200Hz~10kHz, 4
ohm, 10% THD)
OPTICAL CHARACTERISTICS
• Contrast ratio
300:1 (typ.)
• Brightness
300 cd/m2 (typ.)
• Peak contrast angle
6 o'clock
• White Chromacity
x: 0.281 y: 0.311 (at 9300° K)
x: 0.312 y: 0.338 (at 6500° K)
Upper >85° (typ.)
Lower >85° (typ.)
• Viewing Angle (C/R >10)
Left >85 ° (typ.)
Right >85 ° (typ.)
• Response time
<=30ms (typ.)
* These information are subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
• Maximum
1280 x 1024 at 75Hz
• Recommended
1280 x 1024 at 60Hz
17 user definable modes
17 factory preset modes:
H. freq (kHz)
Resolution
V. freq (Hz)
31.5
640*350
70.1
31.5
720*400
70.1
31.5
640*480
59.9
35.0
640*480
67.0
37.8
640*480
72.8
37.5
640*480
75.0
35.2
800*600
56.3
37.9
800*600
60.3
48.0
800*600
72.0
46.9
800*600
75.0
49.7
832*624
75.0
48.4
1024*768
60.0
56.5
1024*768
70.0
60.1
1024*768
75.0
68.7
1152*870
75.0
64.0
1280*1024
60.0
80.0
1280*1024
75.0
(Interlace mode is not applicable)
RETURN TO TOP OF THE PAGE
Automatic Power Saving
If you have VESA's DPMS compliance display card or software installed in your PC, the
monitor can automatically reduce its power consumption when not in use. And if an input from
a keyboard, mouse or other input device is detected, the monitor will automatically "wake up".
The following table shows the power consumption and signaling of this automatic power saving
features:
Power Management Definition
VESA Mode
Video
H-sync
V-sync
Power
Used
LED
color
ON
Active
Yes
Yes
68W (typ.)
Green
Stand-by
Blanked
No
Yes
< 2W
Blinking
Green
Suspend
Blanked
Yes
No
< 2W
Blinking
Green
OFF
Blanked
No
No
< 2W
Blinking
Green
This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS
has determined that this product meets the ENERGY STAR® guidelines for energy
efficiency.
RETURN TO TOP OF THE PAGE
Physical Specifications
• Dimension (WxHxD)
452 x 452 x 200 mm (incl. Pedestal)
• Weight
6.3 Kg
• Tilt (Forward / Backward)
0° / 20°
• Power supply
100 — 240 VAC, 50/60 Hz
• Power consumption
68 W (typ.)
• Temperature (operating)
0° C to 35° C (operating)
-20 ° C to 60° C (storage))
• Relative humidity
20% to 80%
• System MTBF
50K hrs
* These information are subject to change without notice.
RETURN TO TOP OF THE PAGE
Pin Assignment
The 15-pin D-sub connector (male) of the signal cable:
Pin
Assignment
No.
Pin
Assignment
No.
Red video input
DDC +5V
Green video input
10
Logic ground
Blue video input
11
Identical output connected to pin 10
Identical output connected to pin 10
12
Serial data line (SDA)
Ground
13
H. Sync / H+V
Red video ground
14
V. Sync
Green video ground
15
Data clock line (SCL)
Blue video ground
RETURN TO TOP OF THE PAGE
Product Views
Follow the links to see various views of the monitor and its components.
Front View Product Description
RETURN TO TOP OF THE PAGE
Physical Function
Tilt
RETURN TO TOP OF THE PAGE
Installing your LCD Monitor/TV
Front View Product Description • Connecting to Your PC, TV antenna,DVD/VCR etc. • Remo
and Re-install the Base • Basic Monitor TV Connections • Getting Started • Optimizing
Performance
Front View Product Description
Activate PIP (Picture in Picture) window and select size
Switch the monitor between PC mode and TV/Video
PC<->TV/Video
mode
PIP
VIDEO
SOURCE
TV/Video source selection
Power switch On/Off
Increase or decrease the channel number
or
up or down the highlighted function in OSD
Automatically adjust the H/V position, phase and clock
setting
Increase or decrease the level of audio volume
or
increase or decrease the highlighted function in OSD
MENU OK
Open the OSD and select the highlighted function
RETURN TO TOP OF THE PAGE
Side View
1. Headphone Jack
2. LINE OUT Jack
RETURN TO TOP OF THE PAGE
Rear View
(Europe)
DC 12V
DC 12V power in
PC - Video
PC - Audio
S-VIDEO (L)
D-Sub input
PC Stereo input
AV audio (L)
S-VIDEO (R)
AV audio (R)
S-VIDEO
S-VIDEO in
EXTERNAL/
EURO-AV
SCART connection (for Europe only)
75
TV Antenna or CATV cable in
RETURN TO TOP OF THE PAGE
(North America and Asia Pacific)
DC 12V
DC 12V power in
PC - Video
D-Sub input
PC - Audio
S-VIDEO (L)
PC Stereo input
AV audio (L)
S-VIDEO (R)
AV audio (R)
S-VIDEO
S-VIDEO in
L R - AV IN
6a Audio (L) in
Y-Pb-Pr
Component
6b Audio (R) in
6f CVBS in
6c, d, e Component video in
75
TV Antenna or CATV cable in
RETURN TO TOP OF THE PAGE
Optimizing Performance
For best performance, ensure that your display settings are set at 1024x768@60Hz (for 15") or 1280x1
60Hz (for 18").
Note: You can check the current display settings by pressing the "OK"
button once. Go into the Product Information. The current display mode is
shown on the item called RESOLUTION.
You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best performan
out of your monitor, included in this CD. A step-by-step instructions is provided to guide you through the
installtion process. Click on the link to know more about this program.
More about
FP_setup02.exe
RETURN TO TOP OF THE PAGE
Regulatory Information
TCO '95 Information • TCO Environmental Requirements • Energy Star Declaration • Federa
Communications Commission (FCC) Notice (U.S. Only) • Commission Federale de la Comm
(FCC Declaration) • EN 55022 Compliance (Czech Republic Only) • VCCI Class 2 Notice (J
MIC Notice (South Korea Only) • Polish Center for Testing and Certification Notice • North E
Information • BSMI Notice (Taiwan Only) • Ergonomie Hinweis (nur Deutschland) • Philips E
Disposal • Information for UK only
Safety and Troubleshooting • Troubleshooting • Other Related Information • Frequently Aske
(FAQs)
TCO '95 Information
Congratulations!
You have just purchased a TCO'95 approved and labelled product! Your choice has provide
product developed for professional use. Your purchase has also contributed to reducing the
the environment and also, to the further development of environmentally adapted electronic
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encourag
adaptation of goods and services to the environment. The main problem, as far as compute
electronics equipment are concerned, is that environmentally harmful substances are used
products and during the manufacturing. Since it has not been possible for the majority of ele
equipment to be recycled in a satisfactory way, most of these potentially damaging substan
or later enter Nature. There are also other characteristics of a computer, such as energy co
levels, that are important from the viewpoints of both the work (internal) and natural (externa
environments. Since all methods of conventional electricity generation have a negative effec
environment (acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to c
energy. Electronics equipment in offices consume an enormous amount of energy since the
left running continuously.
What does labelling involve?
This product meets the requirements for the TCO'95 scheme which provides for internationa
environmental labelling of personal computers. The labelling scheme was developed as a jo
the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen
Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial an
Development in Sweden). The requirements cover a wide range of issues: environment, erg
usability, emission of electrical and magnetic fields, energy consumption and electrical and
The environmental demands concern restrictions on the presence and use of heavy metals
software. From indicated inactivity to Power Saving Position A2, the total time must not be set
to more than 70 minutes.
NUTEK
VESA State
LED Indicator
Power Consumption
Normal operation
ON
Green
68 W (typical)
Power Saving
Position A1
Suspend
Blinking Green
<2W
Power Saving
Position A2
OFF
Blinking Green
<2W
As an ENERGY STAR® Partner, PHILIPS has determined that this
product meets the ENERGY STAR® guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for quite a long
time.
RETURN TO TOP OF THE PAGE
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer de
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE
EQUIPMENT REGULATIONS.
RETURN TO TOP OF THE PAGE
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimites des appareils
numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces
limites sont conçues de façon à fourir une protection raisonnable contre les
interférences nuisibles dans le cadre d'une installation résidentielle. CET appareil
produit, utilise et peut émettre des hyperfréquences qui, si l'appareil n'est pas
installé et utilisé selon les consignes données, peuvent causer des interférences
nuisibles aux communications radio. Cependant, rien ne peut garantir l'absence
d'interférences dans le cadre d'une installation particulière. Si cet appareil est la
cause d'interférences nuisibles pour la réception des signaux de radio ou de
télévision, ce qui peut être décelé en fermant l'équipement, puis en le remettant
en fonction, l'utilisateur pourrait essayer de corriger la situation en prenant les
mesures suivantes:
Réorienter ou déplacer l'antenne de réception.
Augmenter la distance entre l'équipement et le récepteur.
Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.
Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Toutes modifications n'ayant pas reçu l'approbation des services compétents en
matière de conformité est susceptible d'interdire à l'utilisateur l'usage du présent
équipement.
N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT
MATERIEL BROUILLEUR DU CANADA.
RETURN TO TOP OF THE PAGE
EN 55022 Compliance (Czech Republic Only)
RETURN TO TOP OF THE PAGE
VCCI Notice (Japan Only)
Exhibit 4
Brief Description of Circuit Functions
1.
General
1.1.
Product description
The 18.1” LCD Monitor/TV is specified as a display peripheral with analog video
signal input and include TV/Video function with 18.1” TFT LCD display.
Horizontal scan range is 30 - 80KHz and refresh range is 56 - 75 Hz. This
scan range allows it to display resolution up to 1280*1024 non-interlaced at
75 Hz refresh rate. The image can be adjust through OSD control , these
adjustments can be stored on an board memory including 17 factory pre-set modes.
1.3.
Basic data
1.3.1 LCD panel
Type NR.
Outside dimensions
Pitch ( mm )
Color pixel arrangement
Display surface
Number of color
Backlight
Active area(WxH)
View angle
Contrast ratio
White luminance
: TX46D14VC0HAB(Hitachi)
: 389(H)∗312(V)∗27(D) mm
: 0.2805 x 0.2805 mm
: RGB vertical stripes
: Antiglare
: 8-bit, 16,7M colors
: 8 CCFL edge light
: 359.0(H) x287.2 (V) mm (18.1” diagonal)
: Vertical 170 degree, Horizontal 170 degree (CR > 10 )
: 300:1 ( Typical )
: 300 nits (Typical )
1.3.2. Power supply
AC-DC adapter : 12V/4500mA
Power consumption :
Operating < 68 W(typical)
Standby, off<2W
DC power switch off < 1W
Power cord length
: 1.8M
Power indicator
Auto power saving
: LED (ON: green, Standby and OFF : blinking ).
: EPA, Nutek, VESA DPMS
1.3.3. Horizontal scan
: 30 - 80 KHz
1.3.4. Vertical scan
: 56 - 75 Hz
1.3.5. Input signals
1.PC Signal type
Analog Video : 0.7 Vp-p Linear , positive polarity
Sync : TTL level , separate , positive or negative polarity
TTL level , composite , positive or negative polarity
2.TV signal type
RF signal
: Aerial input
Video signal : SCART input
S-Video input
Audio signal : S-video L/R audio input
PC line in
Scart audio line in
Audio line out
1.3.6 Input connectors
(1) Input analog D-sub connector pin assignment
PIN No.
10
11
12
13
14
15
SIGNAL
Red
Green/ sync on green
Blue
Sense (gnd)
GND
Red GND
Green GND
Blue GND
+5V
Sync GND
Sense (GND)
Bi-directional data
H/H+V sync
V-sync
Data clock
Signal interface
- 1.8M 15Pins, D-sub male with DDC2B Pin assignments
Sync polarity :
-Hori.sync
positive/negative
-Vert.sync
positive/negative
(2) Input SCART connector pin assignment
PIN No.
10
11
12
13
14
15
16
17
18
19
20
21
SIGNAL
Audio output B ( right )
Audio input B ( right )
Audio output A ( left )
Ground (audio )
Ground ( blue )
Audio input A ( left )
Blue input
Function select
Ground ( green )
Comms data 2
Green input
Comms data 1
Ground ( red )
Ground ( blanking )
Red input
RGB switching control
Ground ( video input & output )
Ground ( RGB switching control )
Video output ( composite )
Video input ( composite )
Common ground ( shield )
1.3.7 Front Control
Front Control
Menu
PC
Video
Source
PIP
Power
- +
•
PC
TV
TV/Video
Auto
IR Power
Receiv LED
It’s Top/Down
will be switched
1.3.8 Key board control & definition
There are nine keys used in LCD monitor Plus

Key
name

















Function
VGA mode
TV/video mode
Auto-adjustment
PIP ON/OFF
Menu
Left/Volume down
Right/Volume up
Down/channel
down
Up/Channel up
TV source select
PC/TV
Auto-adjustment
PIP ON/OFF
Menu / Enter
Left/Volume down
Right/Volume up
Down/
NO Function
No Function
Menu / Enter
Left/Volume down
Right/Volume up
Down/Channel
Down
Up/Channel up
Source select
PC/TV select
Up/
No Function
PC/TV select
Note: - controlled by scaler MCU
- controlled by A10 MCU
1.3.9
Resolution
(1) Factory Preset modes ( 17 modes )
10
11
12
13
14
15
16
17
Resolution
640X350
720X400
640X480
640X480
640X480
640X480
800X600
800X600
800X600
800X600
832X624
1024X768
1024X768
1024X768
1152X870
1280X1024
1280X1024
Frequency
31.5K/70HZ
31.5K/70HZ
31.5K/60HZ
35.0K/67HZ
37.9K/72HZ
37.5K/75HZ
35.2K/56HZ
37.9K/60HZ
48.1K/72HZ
46.9K/75HZ
49.7K/75HZ
48.4K/60HZ
56.5K/70HZ
60.0K/75HZ
68.7K/75Hz
64.0K/60Hz
80K/75Hz
Pixel rate
25.175
28.322
25.175
30.24
31.5
31.501
36
40
50
49.498
57.28
65
75
78.75
100
108
135
Sync
(+/-)
(-/+)
(-/-)
(-/-)
(-/-)
(-/-)
(+/+)
(+/+)
(+/+)
(+/+)
(+/+)
(-/-)
(-/-)
(+/+)
(-/-)
(+/+)
(+/+)
Comment
IBM VGA
IBM VGA
IBM VGA
MAC
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
VESA
VESA
1.3.10 Function block
TV / Video processing
- on A10 SSB , processing TV and video I/O signal to analog RGB output .
Video decoder
- SAA7118 , decoder analog RGB signal to CCIR 656 8 bit format digital
Signal
De-interlace
- FLI2200 , further process the 8 bit CCIR 656 format digital signal and
transfer to CCIR601 16 bit format digital signal output to Scaler IC
Scaler (JagASM)
a.) ADC
- brightness control
- contrast control
- R.G.B. sub contrast control
- sample the input video signal according to its pixel rate to form a digital
data for format converter
b.) Format converter
- convert the data from ADC to a LCD panel acceptable data format
- zoom the input video to a full screen display
Microprocessor :
use two Microprocessor to communicate
Scaler MCU:
1.
Scaler IC with A/D converter (Sage JAGASM. )…. >digitized the
VGA RGB signal. And format the digitized RGB signal to the data
Format that LCD panel can accept.
2.
Auto size and phase clock adjustment.
3.
Back light brightness and on-off control.
4.
VGA mode detection and IC register setting.
5.
Video decoder SAA7118….> decode the R, G, B , Composite Sync.
Signal from A10 and output to the De-interlace IC.
6.
FLI2200 de-interlace IC…>de-interlace the video signal.
Keyboard control : Up , Down , Left , Right , Enter , Auto , PIP ON/OFF
A10 MCU:
1.
2.
3.
4.
5.
6.
RC remote control
Keyboard control : PC/TV select , TV/Video source select
TV source select and small signal process control.
Power LED control.
TV/Video LED control
Power management
Two CPU communication
Inverter
- accept +12 V DC voltage
- output 1700 Vrms AC voltage to CCFL ( Cold Cathode Fluorescent Tube,
backlight )
Power supply
- AC adapter : the AC power input from 90 V AC to 264 V AC, can generate
12V / 6A DC power
- DC DC converter : convert 12 V to 5 V , 8V , 3.3 V , 2.5V to system

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2002:07:09 18:29:13-07:00
Create Date                     : 2002:07:09 18:29:01-07:00
Producer                        : Acrobat Distiller 4.0 for Windows
Page Count                      : 20