Pilz and KG IDN02 InduraNET p, wireless remote station User Manual ba pssu wr s idn

Pilz GmbH & Co. KG InduraNET p, wireless remote station ba pssu wr s idn

User Manual

Programmable control systems PSS®PSSu WR S IDNOperating Manual – Item No. 21 841-01
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be madefor internal purposes.Suggestions and comments for improving this documentation will be gratefully received.Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®, SafetyEYE®,SafetyNET p®, the spirit of safety® are registered and protected trademarks ofPilz GmbH & Co. KG in some countries.
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 1ContentsContentsContents PageChapter 1 Introduction1.1 Validity of documentation 1-11.1.1 Retaining the documentation 1-11.2 Overview of documentation 1-21.3 Definition of symbols 1-3Chapter 2 Overview2.1 Scope of delivery 2-12.2 Module features 2-22.3 Features of InduraNET p 2-32.4 Front view 2-4Chapter 3 Safety3.1 Intended use 3-13.2 Safety regulations 3-33.2.1 Use of qualified personnel 3-33.2.2 Warranty and liability 3-33.2.3 Disposal 3-33.3 Approvals for wireless operation 3-43.3.1 European approval 3-53.3.2 FCC approval 3-7Chapter 4 Function description4.1 Module features 4-14.1.1 Integrated protection mechanisms 4-14.1.2 Remote station in InduraNET p 4-14.2 InduraNET p 4-24.3 Process image 4-34.4 USB port 4-44.5 Chip card 4-5Chapter 5 Installation5.1 General installation guidelines 5-15.1.1 Dimensions 5-15.2 Install remote station 5-35.3 Antenna assembly 5-45.4 Install antenna 5-6Chapter 6 Wiring6.1 General wiring guidelines 6-16.2 Terminal configuration 6-26.3 Connection via USB 6-3
ContentsPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de2Chapter 7 Operation7.1 Messages 7-17.2 Display elements 7-27.2.1 Display elements for InduraNET p diagnostics7-2Chapter 8 Technical details8.1 Technical details 8-1
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 1-11.1 Validity of documentation1 Introduction11000IntroductionIntroduction1-1.1Validity of documenta tion1100Validity of documenta tion1-This documentation is valid for the PSSu WR S IDN module. It is valid until new documentation is published.Please also refer to the following documents:`PSSuniversal System Description`PSSuniversal Installation ManualThis operating manual explains the function and operation of the pro-grammable safety system, describes the installation and provides guidelines on how to connect the product PSSu WR S IDN.Using the product PSSu WR S IDN:Remote station to connect the PSSuniversal system to InduraNET p for standard data 1.1.1 Retaining the documentationRetaining the documentation1-This documentation is intended for instruction and should be retained for future reference.
1.2 Overview of documentation1 IntroductionPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de1-21.2Overview of documentation1200Overview of documentation1-1 IntroductionThe introduction is designed to familiarise you with the contents, struc-ture and specific order of this manual.2 OverviewThis chapter provides information on the module's most important fea-tures.3 SafetyThis chapter must be read as it contains important information on in-tended use.4 Function DescriptionThis chapter describes the module's individual components.5 InstallationThis chapter explains how to install the module.6 InterfacesThis chapter describes the module's interfaces.7 OperationThis chapter explains the display elements and advises on what to do if a fault occurs.8 Technical Details
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 1-31.3 Definition of symbols1 Introduction1.3Definition of symbols1300Definition of symbols1-Information in this manual that is of particular importance can be identi-fied as follows:DANGER!This warning must be heeded! It warns of a hazardous situation that poses an immediate threat of serious injury and death and indicates preventive measures that can be taken.WARNING!This warning must be heeded! It warns of a hazardous situation that could lead to serious injury and death and indicates preven-tive measures that can be taken.CAUTION!This refers to a hazard that can lead to a less serious or minor injury plus material damage, and also provides information on preventive measures that can be taken.NOTICEThis describes a situation in which the unit(s) could be damaged and also provides information on preventive measures that can be taken.INFORMATIONThis gives advice on applications and provides information on special features, as well as highlighting areas within the text that are of particular importance.
1 IntroductionPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de1-4
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 2-12.1 Scope of delivery2 Overview22000OverviewOverview2-2.1Scope of delivery2100Scope of delivery2-The PSSu WR S IDN module is supplied with a chip card for storing the configuration data. Additional chip cards are available as an accessory. An antenna is required in order to operate the module. Two antenna types are available:`For remote and base stations:PSS ANT 1 IDN`For base stations only:PSS ANT 2 IDNThe antenna is supplied with an SMA antenna cable which is 2 m long and has an impedance level of 50 Ohm. A suitable 2 m long extension cable is available as an accessory.The chip card reader SCR 335 USB with USB cable is available as an accessory. CAUTION!The radio approval will be rendered invalid if a third-party antenna is used.`InduraNET p devices should only be used with the antennas PSS ANT 1 IDN and PSS ANT 2 IDN.
2.2 Module features2 OverviewPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de2-22.2Module features2200Module features2-The module has the following features:`This module forms the head module of a remote system in InduraNET p.`Antenna connection for InduraNET p`Power supply for max. 2.0 A– When the supply voltage is interrupted, the module supply is buff-ered for 20 ms.– Separate infeed for periphery supply– Separate infeed for module supply`LEDs for:– System status–InduraNET p status– USB status`Electronic modules that can be used for input/output:– All digital standard modules (PSSu E S xD...)
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 2-32.3 Features of InduraNET p2 Overview2.3Features of InduraNET p2300Features of InduraNET p2-InduraNET p enables wireless communication on the PSSuniversal. Data from the standard section is transmitted via radio instead of the module bus. Wireless communication via InduraNET p does not need to be considered in the user program. The module bus cycle is recreated in the remote system. This will in-crease the input/output reaction times of a remote system.Each InduraNET p device is given an ID, which ensures that all subscrib-ers are uniquely identified. Up to ten InduraNET p networks can coexist within one environment. All the settings for wireless communication are stored within the module on a chip card, which is written via a chip card reader.Schematic representation of InduraNET pHead module (FS/ST)I/O module (FS/ST)I/O module (FS/ST)I/O module (FS/ST)I/O module (FS/ST)IDN base stationANTSupplyI/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)I/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)I/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)I/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)Base system Up to 4 remote systemsInduraNET p
2.4 Front view2 OverviewPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de2-42.4Front view2400Front view2-Key:`1: Antenna connection (InduraNET p)`2: Combicon plug-in connector X1 to feed in the module supply and periphery supply`3: LEDs for system diagnostics`4: Labelling strip with:–Order number– Serial number– Hardware version number– Firmware version number on delivery`5: Field for 2D code`6: Labelling strip with interface configuration of the USB port`7: LEDs for InduraNET p diagnostics`8: Module name`9: Chip card slot`10: USB port (Mini-B)PSSuWR S IDNUsb DevUSB2D -3D +5G N DUSB312 0960000000HW 000000RunLnkANTX112345678109
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 3-13.1 Intended use3 Safety33000SafetySafety3-3.1Intended use3100Intended use3-The module may be used as a remote station in InduraNET p, for the wireless communication of ST data. It can be operated with a base sta-tion of type PSSu WB S IDN.The module provides the supply for the module supply and periphery supply within the system.Intended use includes making the electrical installation EMC-compliant. Please refer to the guidelines stated in the “PSSuniversal Installation Manual”. The module is designed for use in an industrial environment. It is not suitable for use in a domestic environment, as this can lead to in-terference.The following is deemed improper use in particular:`Any component, technical or electrical modification to the module`Use of the module outside the areas described in this manual`Use of the module outside the technical details (see chapter entitled “Technical Details”)The remote station may be used in conjunction with the base station PSSu WB S IDN. The remote station may be used in conjunction with the following electronic modules:INFORMATIONThe module is supported by the PSSuniversal Configurator and the PSSuniversal Assistant from Version 1.5.The module is supported by PSSuniversal head modules from ST Firmware Version 12.Module type Module nameDigital input/output modules PSSu E S 4DI(-T)PSSu E S 4DO 0.5(-T)PSSu E S 2DO 2(-T)Voltage distribution PSSu E PD(-T)PSSu E PD1(-T)
3.1 Intended use3 SafetyPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de3-2The module's firmware can be updated to a later version using the Firmware Manager on the PSSuniversal Assistant. For the reason, the module's actual firmware version may not always match the firmware version printed on the front of the unit. Updating the firmware can also expand the module's functionality.INFORMATIONThe module's actual firmware version can only be established using the Firmware Manager on the PSSuniversal Assistant.
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 3-33.2 Safety regulations3 Safety3.2Safety regulations3200Safety regulations3-3.2.1 Use of qualified personnelUse of qualified personnel3-The products may only be assembled, installed, programmed, commis-sioned, operated, maintained and decomissioned by qualified person-nel. Qualified personnel are people who, because they are:`Qualified electrical engineers or`Have received training from qualified electrical engineersare suitably experienced to operate devices, systems, plant and ma-chinery in accordance with the general standards and guidelines for safety technology.It is the company's responsibility only to employ personnel who:`Are familiar with the basic regulations concerning health and safety / accident prevention`Have read and understood the safety guidelines given in this descrip-tion`Have a good knowledge of the generic and specialist standards appli-cable to the specific application.3.2.2 Warranty and liabilityWarranty and liability3-All claims to warranty and liability will be rendered invalid if, among other things:`The product was used contrary to the purpose for which it is intended`Damage can be attributed to not having followed the guidelines in the manual`Operating personnel are not suitably qualified`Any type of modification has been made (e.g. exchanging compo-nents on the PCB boards, soldering work etc.).3.2.3 DisposalDisposal3-The product must be disposed of properly when it reaches the end of its service life.
3.3 Approvals for wireless operation3 SafetyPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de3-43.3Approvals for wireless operation3300Approvals for wireless operation3-InduraNET p devices meet the requirements and specifications of the EU directive 1999/5/EU and may be operated in all European Union countries with the exception of:`Hungary, Latvia, Lithuania, Poland, Romania, Slovakia, SloveniaInduraNET p devices may also be operated in the following countries:`Norway, Switzerland, Liechtenstein, Iceland`Japan`Canada, USA Other countries: On requestIn France, InduraNET p devices may only be operated inside.Please comply with the provisions of ERC/REC 70-03 Appendix 3 - National Restrictions (Annex 3 Band A).Radio approval for the antenna PSS ANT 2 IDN is in progress.
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 3-53.3 Approvals for wireless operation3 Safety3.3.1 European approval European approval 3-
3.3 Approvals for wireless operation3 SafetyPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de3-6
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 3-73.3 Approvals for wireless operation3 Safety3.3.2 FCC approvalFCC approval3-Please note the following when operating the device in the USA and Canada:Installation by professionals only! This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:`(1) This device may not cause harmful interference, and `(2) This device must accept any interference received, including inter-ference that may cause undesired operations. This Class B digital apparatus complies with Canadian ICES-003.Changes or modifications made to this equipment not expressly ap-proved by Pilz may void the FCC authorisation to operate this equip-ment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in-terference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a par-ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-ference by one or more of the following measures: `Reorient or relocate the receiving antenna.`Increase the separation between the equipment and receiver. `Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. `Consult the dealer or an experienced radio/TV technician for help.
3.3 Approvals for wireless operation3 SafetyPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de3-8CAUTION!This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 4-14.1 Module features4 Function description44000Function descriptionFunction description4-4.1Module features4100Module features4-4.1.1 Integrated protection mechanismsIntegrated protection mechanisms4-The module has the following protection mechanisms:`Infeed for module supply– Polarity protection– Voltage monitoring– Transient voltage limitation`Module supply– Short circuit-proofThe module provides the following diagnostic data:`Module status`Module error4.1.2 Remote station in InduraNET pRemote station in InduraNET p4-The module is a remote station in InduraNET p and enables the PSSuniversal to be used as a remote system. The remote station is al-ways the first module in a remote systems. The remote station co-ordi-nates the PSSu module bus on the remote system and exchanges data between the connected I/O modules and an assigned base station in InduraNET p.The module supplies voltage to the modules on the remote system:`Supply to the module bus:– Module supply supplies itself and subsequent modules (right-hand side)– Periphery supply`When the voltages are fed separately, the module supply and periph-ery supply are galvanicaly isolated. If galvanic isolation is not required, a common power supply may be used for the periphery supply and module supply.
4.2 InduraNET p4 Function descriptionPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de4-24.2InduraNET p4200InduraNET p4-Properties of wireless communication `Frequency range 2.4 GHz ISM band`Strong immunity to signals from other wireless services`CFM (Coexistence Frequency Management) guarantees that InduraNET p devices coexist without problem with other radio-based systems. – InduraNET p devices do not use non-overlapping WLAN channels.– InduraNET p devices do not transmit until they have scanned their frequency range (Listen before Talk).– InduraNET p devices switch to free channels in order to avoid colli-sions. Properties of the antenna `The antenna is designed to IP54. It can be installed on a flat surface using one hole mounting.`The SMA antenna cable is 2 m long and has an impedance level of 50 Ohm.`The max. operating range depends heavily on surface reflection and on the transmissivity of surrounding materials. Approximate guidelines are:– 10 m ... 100 m indoors– 100 m ... 1000 m outdoors`Two antenna types are available:– For remote and base station:PSS ANT 1 IDN is optimised for typical indoor applications.– For base station only:PSS ANT 2 IDN with two redundant antennas in one housing is op-timised for high availability in difficult environmental conditions, e.g. for mobile applications.
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 4-34.3 Process image4 Function description4.3Process image4300Process image4-The process image of inputs and outputs is generated in each remote system. The individual process images are combined for the overall sys-tem. The sequence for the remote systems is defined in the PSSuniversal Assistant. The base and remote stations themselves do not occupy any inputs and outputs. Schematic representation:Head module (FS/ST)I/O module (FS/ST)I/O module (FS/ST)I/O module (FS/ST)I/O module (FS/ST)IDN base stationANTSupplyI/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)I/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)I/O module (ST)IDN-Remote-StationANTI/O module (ST)I/O module (ST)I/O module (ST)I/O module (ST)IDN remote stationANTI/O module (ST)I/O module (ST)I/O module (ST)Base system Up to 4 remote systemsInduraNET pPII 0/PIO 0 PII 1/PIO 1 PII 2/PIO 2PII 3/PIO 3 PII 4/PIO 4PII 0 + PII 1 + PII 2 + PII 3 + PII 4PIO 0 + PIO 1 + PIO 2 + PIO 3 + PIO 4
4.4 USB port4 Function descriptionPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de4-44.4USB port4400USB port4-The following functions are available via the USB port:`Show actual hardware`Comparison of actual/registered hardware`Display and update firmware versionsParameters for the module's ST section can either be set via the fieldbus interface or via the USB port. Parameter setting via the USB port has pri-ority over parameter setting via the fieldbus interface. Once parameters for the the head module have been set via the USB port, the ability to set parameters for the module via the fieldbus interface is disabled. The dis-able can be lifted in the PSSuniversal Assistant.Procedure for connecting the head module via the USB port:`Connect PC to head module via USB cable.`Install USB driver.`View the actual hardware registry in the PSSuniversal Assistant and call up other functions.This way it is possible to copy and edit an existing configuration in the PSSuniversal Assistant.INFORMATIONThe USB driver can be found on the PSSuniversal Assistant CD-ROM, in the subdirectory \bin\PILZ_USB_DRIVER
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 4-54.5 Chip card4 Function description4.5Chip card4500Chip card4-The user configures the data for all the InduraNET p modules in the PSSuniversal Assistant and then downloads this configuration data to the chip card via the USB port. The chip card reader SCR 335 USB with USB cable is available as an accessory for this purpose. INFORMATIONThe module will not start up if the chip card is missing or is writ-ten incorrectly.
4 Function descriptionPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de4-6
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 5-15.1 General installation guidelines5 Installation55000InstallationInstallation5-5.1General installation guidelines5100General installation guidelines5-Please also refer to the PSSuniversal Installation Manual.The description below assumes that the mounting rail is already in-stalled.5.1.1 DimensionsDimensions5-A min. 15 cm clearance is required above the mounting rail in the control cabinet to connect the antenna cable on the module.CAUTION!Damage due to electrostatic discharge!Electrostatic discharge can damage components. Ensure against discharge before touching the product, e.g. by touching an earthed, conductive surface or by wearing an earthed arm-band.56,4 mm125,6 mm72,6 mm75,2 mm69,2 mm 2,8 mm21,6 mm(2.448")(2.22") (0.11")(4.945")(2.858")(0.85")(2.96")
5.1 General installation guidelines5 InstallationPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de5-2Dimensions of the antenna ANT1/ANT2 (ANT 2 for base station only):42,3/56,2 mm70,0/103,7 mmM32x1,5 mm136,5/201,5 mm147,3/212,3 mm
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 5-35.2 Install remote station5 Installation5.2Install remote station5200Install remote station5-The remote station is installed in exactly the same way as a PSSuniversal head module.Prerequisite:`The mounting rail must be installed.Procedure:`Install an end bracket to the left of the head module or leave enough space for one.`Slot the groove on the head module on to the mounting rail from below [1].`Push the head module back [2] until you hear it lock into position.Schematic representation:[2][1]
5.3 Antenna assembly5 InstallationPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de5-45.3Antenna assembly5300Antenna assembly5-As with all radio signals, the InduraNET p signals will mainly propagate in the first Fresnel zone. The Fresnel zone is a spheroid, in whose focus the antennas are located.Schematic representation:The size of the Fresnel zone depends on the wavelength of the radio sig-nal and the distance of the antennas.At 2.4 GHz, approximate values for the Fresnel zone's radius R in rela-tion to antenna distance d: d [m]5 8 121620305075100R [m] 0,4 0,5 0,6 0,7 0,8 0,9 1,3 1,5 1,8dR
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 5-55.3 Antenna assembly5 InstallationReception will deteriorate if any objects or parts of the building lie within the Fresnel zone. When positioning the antennas it is possible to distin-guish between three scenarios:`A: The Fresnel zone is not adversely affected.– Optimum conditions `B: The Fresnel zone is adversely affected by the low ceiling and by an object between the antennas. There is visual contact between the an-tennas (straight, dotted line).– These Fresnel zone encroachments will reduce the reception quality. The signals' operating range will be shorter. `C: There is no visual contact between the antennas. – Unfavourable conditions. The signals are only transmitted indirectly and via reflections. Please note also:`The antenna are designed for use inside buildings, particularly on fac-tory floors.`The optimum installation height of the antennas is 1.80 m – 2.00 m, e.g. on top of a control cabinet. `The optimum orientation of the installed antenna is vertical on a hori-zontal surface. `People standing within the Fresnel zone have a particularly adverse ef-fect on reception quality.`Reflections from walls (concrete, metal) lead to local signal quenching. – A diverse antenna (PSS ANT 2 IDN, available as an accessory) can help to improve reception quality on mobile, remote stations.A B C
5.4 Install antenna5 InstallationPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de5-65.4Install antenna 5400Install antenna 5-The antenna is positioned on the control cabinet or on a flat surface, us-ing one hole mounting. The InduraNET p antenna cable is a 2 m long co-axial cable for high frequency applications with an impedance level of 50 Ohms. Please refer to the section entitled "Antenna assembly" for information on providing sufficient reception.Procedure:`In the control cabinet ceiling, punch or drill a hole suitable to take an M32 thread fitting (> 32 mm diameter).`Feed the antenna cable through the punched hole and assemble the antenna. `Screw on the antenna using the nut on the M32 thread.`Install the antenna cable from the antenna to the InduraNET p station. – The minimum bending radius is 15 mm.– The antenna cable must not be bent or trapped.– The antenna cable must not be split and then rejoined.– Excess cable must not be wound like a coil. Excess cable should be looped.`Screw the antenna cable on to the socket labelled “ANT” on the InduraNET p station.– The torque on the SMA screw connection is 0.7 – 1.1 Nm. You can achieve the appropriate torque by tightening the screw firmly by hand. NOTICEInduraNET p devices may be damaged if they are operated with-out an antenna. `Always operate the PSSu WR S IDN device with the antenna connected. CAUTION!The radio approval will be rendered invalid if a third-party antenna is used.`InduraNET p devices should only be used with the antennas PSS ANT 1 IDN and PSS ANT 2 IDN.
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 5-75.4 Install antenna5 InstallationThe 2 m extension cable attenuates the signal by approx. 3 dB. Attenu-ation of 3 dB halves the transmitted output. For this reason, only use the extension cable where reception conditions are good and operating ranges are short. `For reasons of electromagnetic compatibility, the extension cable may only be laid with group 1 cables (see PSSuniversal Installation Manual)
5 InstallationPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de5-8
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 6-16.1 General wiring guidelines6 Wiring66000WiringWiring6-6.1General wiring guidelines6100General wiring guidelines6-Please note:`Please refer to the technical details regarding the requirements of the supply voltages.`Safe electrical isolation must be ensured for the external power sup-plies that generate the supply voltages. Failure to do so could result in electric shock.`The external power supplies must comply with the current applicable standard EN 60950-1, EN 61140, EN 50178 or EN 61558-1.`The maximum current load for the periphery supply on the module bus is 10 A.`With a common 0 V supply for module supply and periphery supply: Connect together the 0V connections on all the external power sup-plies and earth the 0 V mains at a single point.`The connection of the 0 V supply to the central earth bar or earth fault monitor must be in accordance with the relevant national regulations (e.g. EN 60204-1, NFPA 79:17-7, NEC: Article 250).`Minimum range for cable cross sections on connection terminals in mm2:– Power supply: 1.5 (AWG16) ... 2.5 (AWG12)– Functional earth: 1.5 (AWG16) ... 2.5 (AWG12)`Use copper wiring.
6.2 Terminal configuration6 WiringPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de6-26.2Terminal configuration6200Terminal configuration6-`n.c. = not connectedConnector description Terminal configuration5-pin Combicon plug-in connector X1 1: +24 V infeed for periphery supply2: 0 V infeed for periphery supply3: n.c.4: +24 V infeed for module supply5: 0 V infeed for module supplyUSB AssignmentMini-B USB connector 1: n.c.2: D- USB Data –3: D+ USB Data +4: n.c.5: GND Ground5115
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 6-36.3 Connection via USB6 Wiring6.3Connection via USB6300Connection via USB6-Please note the requirements of the USB standard for USB 2.0 and for Mini-B USB ports.The maximum cable runs for USB connection cable are 5 m.
6 WiringPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de6-4
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 7-17.1 Messages7 Operation77000OperationOperation7-7.1Messages7100Messages7-All errors and faults detected by the electronic modules on a remote sta-tion are signalled to the base station via InduraNET p and entered in the head module's error stack.(1) There are two levels of overtemperature.`Too warm:If a module's temperature exceeds a theshold value, the module sends a warning to the head module. If the temperature drops back below the threshold value, the module sends an all-clear.`Too hot:If a module's temperature exceeds a further theshold value, the mod-ule sends an error message to the head module.Module error Explanation RemedyStart-up error Error as the PSSu system starts up Change faulty module.Configuration Error Incorrect module type configured. The configured hardware registry does not match the actual hardware regis-try.ST communication error Error during ST communication Change faulty module.Bus termination error There is no terminating plate or there is a bad contact with the module bus.Install a terminating plate with inte-grated end bracket or insert the base modules together correctly.Temperature error: Too warm (1) Ambient temperature too high:Error stack entryEnsure there is sufficient ventilation in the control cabinet or prevent over-load.Temperature error: Too hot (1) Ambient temperature too high: Module resetEnsure there is sufficient ventilation in the control cabinet or prevent over-load.Overvoltage error A system voltage or infeed is too high. Stabilise the supply or change the faulty supply voltage module.Undervoltage error A system voltage or infeed is too low. Stabilise the supply or change the faulty supply voltage module.
7.2 Display elements7 OperationPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de7-27.2Display elements7200Display elements7-Key:7.2.1 Display elements for InduraNET p diagnosticsDisplay elements for InduraNET p diagnostics7-The module has LEDs to display various states on the remote station (“Usb” LED and “Dev” LED).(*1) An addressing error (flashing red LED) may be caused by one of the following factors: `Terminating resistor is missing.`A module is defective.`A module does not have valid software.`Invalid hardware registryLED onLED flashesLED offLED KeyName Colour StatusUsb - - - No data is being transmitted via the USB portGreen Data is being transmitted via the USB portDev - - - PSSu system error, no start-upGreen Remote system is running cor-rectly Red Error in the re-mote station Red Addressing er-ror (*1)Usb Dev--- -- -DevUsb
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 7-37.2 Display elements7 OperationThe module has LEDs to display various InduraNET p states (“Run” LED and “Lnk” LED).(*2) A chip card error (red LED) may be caused by one of the following factors: `No chip card in the remote station`Unable to read chip card.`Data on the chip card is invalid.LED KeyName Colour StatusRun - - - Remote station not in operationRed Chip card error (*2)Red The hardware configuration of the remote sys-tem does not correspond to the configura-tion stored on the chip card. Green Remote station is ready to transmit data Lnk - - - InduraNET p not in operation Green InduraNET p is runningRed/green InduraNET p is running with fleeting inter-ruptions Red No connection to InduraNET pINFORMATIONAfter a restart the InduraNET p configuration data is loaded from the chip card. This process lasts approximately 5 s. During this time the LEDs will flash in quick succession.PSSuWR S IDNUsb DevUSB2D -3D +5G N DUSB312 0960000000HW 000000RunLnkANTRunLnkX1
7 OperationPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de7-4
Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de 8-18.1 Technical details8 Technical details88000Technical detailsTechnical details8-8.1Technical details8100Technical details8-Technical details PSSu WR S IDNApplication range StandardModule's device code 0006hElectrical dataInternal supply voltageSupply voltage range of module supply 4.8 - 5.4 VCurrent and power consumption from module supplyModule's current consumption 215 mAModule's power consumption 1.10 WInfeed for Module SupplyVoltage 24 VDCVoltage tolerance -30 %/+25 %Output of external power supply (DC) 12.0 WMax. continuous current that the external power supply must provide 0.8 AInrush current that the external power supply must provide 4.0 AInfeed for Periphery SupplyVoltage 24 VDCMax. continuous current that the external power supply must provide 10.0 AVoltage output Module SupplyVoltage 5 V DCVoltage tolerance -2 %/+2 %Current load capacity 2.0 ABuffer in the case of supply interruptions in accordance with EN 61131-2, EN 61496-1Short circuit-proof yesInduraNET p interfaceApplication range Standard applicationsApplication in accordance with ARIB STO-T 66 (19,2), EN 300328 V1,7,1, EN 301489-1 V1,6,1, EN 301489-3 V1,4,1, FCC Part 15-249Working frequency range 2,405 - 2,479 MHzChannel spacing 1 MHzNumber of channels 75Modulation GFSKFrequency deviation -160 - 160 kHzTyp. transmitter output EIRP 18 dBm/64 mWMax. transmitter output EIRP 20 dBm/100 mWReceiver type SuperhetMax. receiver sensitivity when PER=0.1% -90 dBmFrequency stability -2.5 - 2.5 ppmIntermediate frequency fZF=fLO-fRX=(8/7*fRX+2MHz)-fRXEnvironmental dataClimatic suitability EN 60068-2-14, EN 60068-2-1, EN 60068-2-2, EN 60068-2-30, EN 60068-2-78Ambient temperature 0 - 60 °CCondensation noEMC EN 55011: class A, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-6-2, EN 61000-6-4, EN 61131-2
8.1 Technical details8 Technical detailsPilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, GermanyTelephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de8-2Vibration to EN 60068-2-6Frequency 10 - 150 Hz, 10 - 60 Hz, 60 - 1,000 HzShock stress11 msProtection typeMounting (e.g. cabinet) IP54Housing IP20Mechanical dataHousing materialFront PCBottom PCDimensionsHeight 128.4 mmWidth 75.2 mmDepth 79.4 mmColour of front plate dark greyWeight 169 gEnvironmental data
• …• www21 841-01, 2008-03 Printed in Germany© Pilz GmbH & Co. KG, 2008Pilz GmbH & Co. KGSichere Automation Felix-Wankel-Straße 273760 Ostfi ldern, GermanyTelephone: +49 711 3409-0Telefax: +49 711 3409-133E-Mail: pilz.gmbh@pilz.dewww.pilz.com+49 711 3409-444• Technical supportIn many countries we are represented by sales partners.Please refer to our homepage for further details or contact our headquarters.

Navigation menu