Pixel Enterprise ROOK-RF-508 Wireless flash trigger User Manual

Pixel Enterprise Limited Wireless flash trigger

Contents

User Manual 1

Thank you so much for purchasing PIXEL product, ROOK is a professional grouping flash trigger. TTL mode available on transmitter hot shoe and sync with off shoe trigger together. Off shoe trigger can be grouped the flash and Remote the camera. ROOK is using global free FSK 2.4GHz which is more stabilize.1、Make sure the camera is powered off before install device.2、This is electronic products accessories; some of the environment causes may affect the working. However this is hardly ever to get this situation, don't worry!3、This component can't be strong vibration, or may lead to product failure.4、For a long time non-use, please turned off the transmitter and the receiver's power and remove the battery.5、The batteries should not install anti-polarity; otherwise the batteries may leak. corrosive liquids, heat or explosion.6、When the product connected to the device, Do not pull the wires.7、Do not put it in high temperature, such as a closed car under direct sunlight, the control panel and other high-temperature areas.8、keep dry, do not use wet hand contact with the product, the product must not be immersed in water or exposed to rain, and this may lead to not work properly.9、Do not use flammable gases in violation of this warning may cause an explosion or fire.、10 Because of this product is included battery; please strictly follow the instruction for operation. Otherwise its may cause an explosion, fire or personal injury.Overview1ROOK is a professional grouping flash trigger.2Transmitter hot shoe support TTL and sync with off shoe flash.3Wake-up function available, the flash will be wake up automatically.4Through studio light to connect PC or USB socket, the sync speed up to 1/320s (Sync time may have little bit inacurracy as difference camera model )5 Available to control the shooting or through master camera to control slave camera.、、、、、3ReceiverProfessional Flash TriggerInstruction ManualROOK1Power/groupswitchChanel settingIndicator LightBattery compartment11223345767Output socket456eesssional Fl Flaash Trh Trh TriggerrOKSony series camera, Minolta series camera ROOK Model compatible list as below：Transmitter(TX)Receiver(RX)Canon series cameraNikon se ries camera, Samsung seri es cameraFujifi lm series camera, Pa ntex series camera Compatible212345768Trigger pointGroup IndicateLightChanel settingPower/group settingBattery compartment1 2 34576 8Input/outputsocketTransmitterHot shoe protectorIncluded ItemsSpecification4Battery Installation: Set transmitter and receiver to the same channel5AAA +- AAA +-Please locate the battery accordingto the icon in the battery compartment.Channel Setting:Set transmitter and receiver to thesame channel1.Slide the switch to change channel.2.Channel changing as:CH1→ CH2→ CH3→CH4 (as figure)CH 1CH 4CH 2CH 3For a long time non-use, please turned off the transmitter and the receiver's power and remove the battery.* Transmitter and receiver must be set as the same channel.* A、B、C LED light on means the current setting will be working with transmitter.4. No action within 2 seconds, the group LED light will off.*Receiver only get signal from transmitter when the current groupsetting of receiver is included in the validate group of transmitter.Testing:1. Check power on or off.2. Check the frequency of transmitter and receiver.3. Check the group setting of transmitter and receiver.6Group setting:Group setting on transmitter1.wake up group display, and show the current controlling group. Slightly press [ ] to show group mode which showing the current working group. 2. Press again [ ] to change group.3. Group changin g a s : CH 1CH 1CH 1CH 3Group setting on receiverPut Power/group switch at A/B/C, and then turn on the receivers.3.Trigger the Flash.1.Insert flashgun on the receiver and turn on the flash power; set the flash index as minimum.2.Full press the test button1. Tight the Hot shoe with screw, and then turn right to release.2. Plug the transmitter on the camera hot shoe.3. Tight the Hot shoe with screw, and then turn left to lock.Connect the transmitter to camera hot shoe1. Plug PC-3.5 connecting cable to transmitter 3.5mm socket.2. Plug PC-3.5 connecting cable to camera PC socket. Connect transmitter to camera via PC-3.5 connecting cable.7How to connect the relative photo equipmentTesting the receiver signal as below:(2(11. Split the protecting film on the receiver holder and stick it on the studio light as figure.2. Mount the receiver on the receiver holder.3. Use 3.5-3.5 or 3.5-1/2 according to studio light socket.4. Plug 3.5mm side into the transmitter input.5.Insert another side into the studio light socket.Connect the Receiver to Studio Light2311. Unlock the Speedlite Flash locking screw.2. Insert the Speedlite Flash into the receiver hot shoe as figure.3. According to the flash locking method to lock the speedlite on receiver.Connect the Receiver to Speedlite Flash1.Plug shutter connecting cable (3.5mm side) into thereceiver socket. 2.Plug shutter connecting cable (camera side) into the camera shutter release socket.Connect Receiver to Camera 8(1 (2Cautions before useReceiver holderfor Canon for Nikon for Sony for Olympus/PanasonicFor Sonyfor Olympus/PanasonicFor NikonFor CanonModelAbove brand name is registered by the respective owner.Qriginal speedlite, studio light,Metz, SUNPAK,SigmaOlympus/Panasonic series cameraFeaturePrepare to use*PC-3.5 connecting cable should be purchased separately.（ ）Trans m itterTrans m itter Receiver Transmi tte r Re ceiver*The shutter cable should be purchased separately.Wireless Frequency System:Operating Distance: Shutter Sync Speed: 1/200S Group setting: 3 difference group (7 combinations)Wireless Channel: 4 Stand-by Time 250 hours： : Transmitter: 5yearsPower: AAA x2 Weight: Transmitter 48.5g (without battery) Receiver 44.0g (without batter y) FSK2.4GHzup to 200mReceiver Please check the package and make sure the below items are already in the box. If there's missed anything, please contact with the distributor directly.ROOK ROOK Receiver 1pcReceiver holder: 1pc Hot shoe protector: 2pc Manual: 1pcTransmitter 1pcA、B、C→ A、B→A、C →B、C → A → B →C → A、 B、CTurn power on/off:Transmitter:Receiver:(Turnpower off)Hold [ ] 2 seconds to turn on transmitter, then group LED light on for 2 seconds, and show which current light. It can be used trigger the flash and control shutter. You could turn off power by pressing [ ] 2 seconds again, then [LED light] blink red three times.Then power off.Switch [Power/group switch] to A or B or C to turn on receiver power; the receiver will be stayed in the current group and the LED light blink as red every 2 seconds.Switch [Power/group switch] to OFF; the receiver power is off,and the light stop blinking.(Turnpower on)Hot shoe foot withscrew Indicator LightShutter release/testbuttonShutter release/testbutton

Navigation menu