Pixel Technology X900C Speedlite User Manual 1

Shenzhen Pixel Technology Limited Speedlite 1

User Manual

12 unit is independent, without interference;3. Under ALL mode, all of units will join in firing. MULT Mode1. A:B can set different flash output of group A and B individually, except group C. The frequency and flash times of group A and B are the same;2. A:BC can set the flash output of group A, B, C. The flash power of the three groups can be set separately. And the frequency and flash times of the three groups are the same;3. Under ALL mode, all of units will join in firing. The frequency and flash times of every firing group are the same.※ Under MULT mode of wireless flash, flash frequency can be set between 1-199Hz. Error Warning PromptWhen an error occurs on the flash or overheating protection is activated, the following information will display on the screen:Motor Error Prompt:WARNING: MOTOR ERRORMotor Error, Battery and Flash Head Overheating Prompt:WARNING: MOTOR ERROR BAT LAMP TEMPERATUREMotor Error, Flash Head Overheating Prompt:WARNING: MOTOR ERROR LAMP TEMPERATUREFlash Head Overheating Prompt:WARNING: LAMP TEMPERATUREBattery Overheating Prompt:WARNING: BATTER TEMPERATUREUnknown Error Prompt:WARNING: ERROR 90※ When a prompt occurs on flash motor and unknown error, you are advised to switch on-off the flash repeatedly to make it self-recovery. After recovery, the prompt info will disappear, and you can reuse it. If not, you are advised to contact the dealer for repair.※ When you use the flash continually, flash head and battery overheating protection will be activated, then the LCD display screen will shows error prompt and restrict flash firing. Now please turn off the flash and allow a rest time for reuse. Then the prompt info will disappear, and you can reuse it.-3- -4- Dial SelectorThis dial selector is applied to adjust setting parameter of the flash. Turn left to reduce setting parameter, and turn right to increase setting parameter.Operation InterfaceIntroductionX900 Speedlite is the newest one developed by Pixel which has multifunction and fast recycle time. Featured with fast recycle time, it can use Lithium battery, AA battery and can be used with Pixel power bank TD-386 which has high power capacity. When use lithium battery or power bank TD-386, the recycle time is less than 1.5 sec, full power output is up to over 700 times that makes you cannot miss the amazing moment; It has the configurations of HSS, high GN, wireless control, stroboscopic and so on. The frequency of stroboscopic is up to 500 times, the performance is more strong and stable; In the area of controlling Speedlite, beside the optical control, it imports wireless control system FSK2.4GHz and supports the direct wireless control between King PRO, Speedlite and Speedlite making the match between speedlites more free. X900 Speedlite ingeniously adopts 4 watt full white light LED creative set light, LCD lattice screen with high definition,multi-matrix overheat warning system and other thoughtful equipment. It is a Speedlith with high performance, multifunction and multipurpose. Beside that, users can upgrade firmware through Mini port to enjoy official and thoughtful services from Pixel.In 1st Curtain modethe icon don`t showFUNC Selector IconSYNC Mode Icon13X900 master modeKing pro master modeThe gear installed on the camera must be set as master mode:1. Communication mode settinIntroduction of operationThe master mode setting of King Pro: After power-on, gently pressing the right first button on the king pro installed on the camera, entering into the setting of master mode and slave mode to set the mode by pressing the left first button that will be display a “+” on the screen and the second button that will display a “-” on the screen. Then, pressing the first left button that will display an “OK” on the screen.The master/slave mode setting of X900: you can enter into the master mod by pressing the first upper left button on flash for a long time (the button of “RMOT”) and choose FSK2.4GHz wireless mode as flash mode. [ ]Both Wireless trigger King pro and x900 pro have FSK2.4GHz wireless control mode, and X900 Speedlite has a built-in wireless receiver; When used with king pro, the x900 pro flash can be controlled without Receiver and all kinds of flash modes can be controlled by king pro, for example: TTL, M, focal length, exposure compensation and so on；At the same time, two flashes can be used in wireless flash mode through 2.4GHz communication without any trigger. (Beside FSK2.4GHz mode, x900 pro has optical mode. The introduction is about the operation mode of FSK2.4GHz)The introduction of the operation of Pixel Wireless Trigger King PRO and X900 Speedlite wireless control.Please make sure the communication mode, channel and group of king pro and x800 pro are correct, otherwise they cannot communicate and be used normally.The king pro and x800 pro installed on the end of camera should be set as master mode, the off-camera flash should be set as slave mode; then, the group of master mode and slave mode and the channel should be set as the same.Pressing the button of “RMOT” for a long time, you can enter into the maser mode. control function. The speedlite mounted on the camera can transmit signal via optical pulse to control firing re m o t e ly. Wh e n u sin g w irel e s s fl a s h mo d e , th e speedlite mounted on the camera should set as Master mode, and the off-camera flash set as Slave mode. Optical transmis-sion flash is achieved by optical pulse, not wireless signal transmission, so the transmission distance is very short. Please note the following issues when using:1. Make sure the slave unit within effective control range when using optical transmission flash mode;2. The receiving signal sensor of slave unit should face to master unit;3. You are required to use flashes that are equipped with an optical transmission wireless shooting function;4. Please do not place any obstacles between the master unit and salve unit when using optical transmission flash mode, or it may affect optical signal transmission;5. Under optical transmission flash mode, use ETTL flash and M flash support high speed sync (HSS) and 1st curtain sync. When using MULT flash, it supports 1st curtain sync. Optical Transmission Flash Function ParameterTransmission Method: Optical pulseMode Control: Master/Slave,S1/S2 Channel Control: 1-4 channelsGroup Control: 3 groups (A/B/C)Transmission Distance: about 0.7-10mHorizontal: ±40°; Vertical: ±30° (facing to master unit)Flash Ratio Control: 1:8-1:1-8:1Sync Mode: HSS, 1st curtain syncOptical Transmission Flash Control Operation IntroductionPress and hold RMOT button to enter wireless flash *master mode; after entered wireless flash mode, press and hold SET RMOT button to enter wireless flash Slave mode. Press and hold again to exit wireless flash mode. Optical Transmission mode can set Master/Slave group control, channel control, Master flash On/Off. 1. Master/Slave Mode Setting Master Mode Setting: press and hold RMOT button to *enter wireless flash control mode. Gently press this button again and then turn dial selector to select optical transmission mode[ ] . If this mode is already displayed after entered wireless flash control interface, then there is no need to make setting. When using optical transmission flash, the speedlite mounted on the camera should set as this mode. Slave Mode Setting: after entered wireless flash mode, press and hold SET RMOT to enter Slave mode [SL]. *Gently press SET RMOT button again and then turn dial *selector to select Slave optical transmission mode [ ] . If this mode is already displayed on the interface after entered slave mode, then there is no need to make setting.2. Group Control Setting After entered wireless flash Master mode, continuous Manufacturer: Shenzhen Pixel Technology LimitedAddress: Rm1411, AAA Building, Renmin Road, Longhua District, Shenzhen City.TEL: 400-8084899Website: www. Pixelhk.com.cnProduct Standard: Q/PSKJ004-2016 817PSM V10.01154177 6 built-in AF-assist beam activates automatically to help autofocus.Press and hold to enter FN function setting, and then continuously press this button to move the setting icon to AF-assist Beam Setting, and then turn dial selector to turn on AF [ ] or turn off AF [ ]. Press OK to confirm the settings.Stand-by Time Setting Press and hold to enter FN function setting, and then continuously press this button to move the setting icon to Stand-by Time Setting, and then turn dial selector to select stand-by time:[ ] means 5mins stand-by time, [ ] means 10mins stand-by time,[ ] means 30mins stand-by time,[ ] means 1hr stand-by time,[ ] means 2hrs stand-by time,[ ] means 4hrs stand-by time, [ ] means non-sleep mode. Press OK to confirm the settings. When under wireless Slave mode, the default stand-by time as 1 hour. When flash entered sleep mode, the flash display screen will show [ ] icon. Half-press camera shutter or Flash Test Button to wake up the flash. LOCK It's applied to lock the parameter settings of the flash, avoiding the flash parameter may be changed accidently. MODE Flash mode button. It's applied to set the flash mode. You can set the flash mode to ETTL full auto flash, Manual flash and Mult flash mode individually. Press and hold this button to reset your flash to the original factory settings. ETTL ETTL Flash Mode. The camera and flash metering system will work together to make correct exposure, thus the sh oot ing subject and background wil l ge t balanced exposure. Under this mode, it's available to set the EV and FEB. The EV and FEB adjustable power is between -3.0EV to + 3.0EV in 1/3 increments. M Manual Flash Mode. You can set the flash output from 1/128 power to 1/1 full output in 1/3 increments. Set flash output power with dial selector. Turn left to reduce setting parameter, and turn right to increase setting parameter. MULT Mult Flash Mode. Mult flash mode can make one image displays as a serial continuous moving image. Under Mult flash mode, you can set flash output power, flash times and flash frequency.9 press SET RMOT button, and then move setting icon to *Group Control Setting [ ALL], then turn dial selector to select the group as needed. Master Group Mode Switch: ALL→A→:B→A:BCSlave Group Mode Switch: A→B→C3. Flash Channel Setting After entered wireless flash Master mode, continuous press SET RMOT button, and then move setting icon to *Channel Setting [CH1], then turn dial selector to select flash channel. Optional channel: CH1-CH4, 4 channels in total. Slave flash channel need to set in the slave interface, the method is the same as master channel setting. If the transmission channels of the master unit and slave unit are different, then the slave unit won't fire. Both Master and slave must be set to the same channel.4. Master Flash On/Off Setting After entered wireless flash Master mode, continuous press SET RMOT button, and then move setting icon to *Master Flash On/Off [ ] , then turn dial selector to select Master Flash On[ ] or Off [ ] . When flash is On, master flash will join in exposure. When flash is Off, master flash will not join in exposure.※ Under Slave mode, it's not available to set flash On/Off. Here flash is On by default. ※When using optical transmission function and the Master flash set as OFF, the Master flash may join in exposure under low sync speed according to optical pulse transmission theory. ETTL ModeUnde r E T TL m o de, you can s e t g roup fla s h r atio, ALL→A:B→A:BC.1. A:B can set the flash ratio of group A ,B;2. A:BC can set the flash ratio of group A, B. Under this mode , group C is in dependent which c an be set individually;3. Under ALL mode, all of units will join in firing.※ If need more flash output, you can invite the numbers of the slave unit which is unlimited. M ModeUnder manual wireless flash mode, the Master unit can set different flash output for every slave flash (every group).1. A:B can set the flash output of group A ,B, except group C;2. A:BC can set the flash output of group A, B, C. Each group unit is independent, without interference. 3. Under ALL mode, all of units will join in firing. MULT Mode1. A:B can set different flash output of group A and B individually, except group C. The frequency and flash times of group A and B are the same;2. A:BC can set the flash output of group A, B, C. The flash power of the three groups can be set separately. And the frequency and flash times of the three groups are the same;11 1. Master/Slave Mode Setting Master Mode Setting: press and hold RMOT button to *enter wireless flash control mode. Gently press this button again and then turn dial selector to select radio transmission mode[ ]. If this mode is already displayed after entered wireless flash control interface, then there is no need to make setting. When using wireless flash, the speedlite mounted on the camera set as this mode. Slave Mode Setting: after entered wireless flash mode, press and hold SET RMOT button to enter Slave mode *[SL]. Gently press this button again and then turn dial selector to select Slave optical transmission mode[ ]. If this mode is already displayed on the interface after ente red slave mode, then there is n o need to make setting.2. Group Control Setting After entered wireless flash Master mode, continuous press SET RMOT button, move setting icon to Group *Control Setting [ ALL], then turn dial selector to select the group as needed. Master Group Mode Switch: ALL→A:B→A:BC Slave Group Mode Switch: A→B→C3. Flash Channel Setting After entered wireless flash Master mode, continuous press SET RMOT button, and then move setting icon to *Channel Setting [CH1], then turn dial selector to select channel. Optional channel: CH1-CH15,15 channels in total. Slave flash channel need to set in the slave interface, the method is the same as master channel setting. If the transmission channels of the master unit and slave unit are different, then the slave unit won't fire. Both Master and slave must be set to the same channel.4. Master Flash On/Off Setting After entered wireless flash Master mode, continuous press SET RMOT button, and then move setting icon to *Master Flash On/Off[ ], then turn dial selector to select Master Flash On [ ] or Off [ ]. ※ Under Slave mode, it's not available to set flash On/Off. Here the flash is On by default. ETTL ModeUnde r E T TL m o de, you can s e t g roup fla s h r atio, ALL→A:B→A:BC.1. A:B can set the flash ratio of group A ,B;2. A:BC can set the flash ratio of group A, B. Under this mode , group C is in dependent which c an be set individually;3. Under ALL mode, all of units will join in firing.※ If need more flash output, you can invite the numbers of the slave unit which is unlimited. M ModeUnder manual wireless flash mode, the Master unit can set different flash output for every slave flash (every group).1. A:B can set the flash output of group A ,B, except group C;2. A:BC can set the flash output of group A, B, C. Each group 103. Under ALL mode, all of units will join in firing. The frequency and flash times of every firing group are the same.※ Under MULT mode of optical transmission flash, flash frequency can be set between 1-199Hz.※ Opt ical trans mis sion is ach iev ed by optical p ulse, s o its transmission performance is not so good and transmission distance is short. For better use wireless flash function, we are advised to use wireless flash mode. Being less affected by obstacles, wireless signal transmission and control efficiency are much higher. S1/S2 Optical Control ModeS1 Manual Optical Transmission Mode: when set flash as this mode, it can work with the first firing of the Master flash synchronously. Set Master flash as manual M mode. The ETTL or MULT mode cannot be fired.S2 ETTL Optical Transmission Mode: when set flash as this mode, it can fire with the ETTL mode of the Master flash synchronously. Set Master flash as ETTL auto metering mode. The M or MULT mode cannot be fired.1. After entered optical Slave Mode (SL), gently press MODE FN button and then turn dial selector to select *MODE S1 or MODE S2 mode.2. Under Slave MODE S1 or MODE S2 mode, press +/- and then turn dial selector to adjust the output power of Slave Flash.※ MODE FN: namely gently press Slave mode, press and hold to *enter FN function setting.※The X900 wireless flash (2.4GHz) system is not compatible with that of Canon original flash. It can only be compatible with part of Pixel wireless products. Transmission Method: FSK2.4GHzMode Control: Master/Slave Channel Control: 1-15 channelsGroup Control: 3 groups (A/B/C)Transmission Distance: about 50MFlash Ratio Control: 1:8-1:1-8:1Sync Mode: HSS, 1st curtain sync Wireless flash control can set Master/Slave group control, channel control, Master flash On/Off. 7※continuous flashes, allow a rest time of the flash at least 15mins.※If you fire more than 10 continuous flashes, the safety function may activate and restrict flash firing. If this happens, please allow a rest time of the flash at least 15mins.● Do not expose this product in high temperature location or confined spaces exposed to strong direct sunlight and other overheating places.● Keep it dry. Do not touch this product with wet hand. Do not expose this product to water or rain, or you may not be able to use it.● Do not use it in inflammable gas, or it may cause explosion or fire.● This product involved in battery. Please strictly follow the corresponding operations related to battery, or it may cause explosion or fire.● Do not put the component in strong vibration, or it may cause fault of this product. ● Remove the batteries during long periods of non-use.● Do not use the flash light in a short distance from the eyes, or it may cause possible injury to eyes or blindness.● After continuous use, it will be very hot. Do not touch, or it may cause burn.● After continuous use, the battery might be hot. Please be careful when changing new battery.● Do not disassemble or maintain this product by yourself. The internal high voltage will cause electric shock.●Only the same brand and battery type can be used.12GN: 60 (ISO100 200mm)Flash Coverage Range:20 -200mmAuto Zoom: According to shooting angle and image to auto adjust the coverage rangeManual Zoom:According to camera or flash setting to adjust the zoom rangeFlash Mode: ETTL/M/MULTStroboscopic Flash: 1-500HzWireless Flash:Radio transmission/ Optical transmission support Master/ Slave, S1/S2SYNC Mode: High Speed Sync, 1st Curtain Sync, 2nd Curtain SyncAdjustable Angle:Up/down: -7/90 degree Left / Right: 180 degree/180 degreeManual Flash: 1/128-1/1 output control (1/3rd increments)Recycle Time: Less than 2.5 sec (1/1 full power output)LCD Display Screen: High definition dot matrix screenInternal Power Source:4×AA size alkaline batteries or rechargeable batteries (4×1.5V)External Interface: Hot shoe, PC port, USB port, external power portEV: In 1/3rd increments (±3 stops)FEB: In 1/3rd increments (±3 stops)Battery Life: 180 times (1/1 flash output, with Sanyo Eneloop batteries)Fluorescent tube: Ultra-long battery life designOverheating Warning:Multi dot matrix temperature control, battery overheating warningAF-Assist Beam:Firmware Upgrade: SupportDimension: 73.50mm×61.00mm×192.00mmWeight: 420.00g (excluding batteries)SupportInstruction ManualEnglishFor CanonX900 C5 RMOT Wireless Flash Button*Press and hold this button to enter wireless control mode. The wireless mode and optical transmission mode can be set individually. First, press and hold this button to enter wireless flash mode; and then press and hold this button again to enter Slave mode; and press and hold once again to exit wireless flash mode. SET RMOT: namely gently press to set SET function. *Press and hold this button to enter next function. With mark function button means press and hold this *button to enter the corresponding function setting. -/+ Function Button This function button is applied to adjust output parameter of the flash, FEB and other functions. Function adjustment alters from shooting mode. It's subject to image display function. FEB, namely flash exposure bracket. When displaying FEB, you may set flash exposure bracket. ZOOM This Zoom button is applied to set Zoom mode. Zoom mode includes manual zoom [ ] and auto zoom [ ]. Set this function with dial selector.※ Focal distance can set as 20-200mm. Some cameras do not support higher focal distance. The setting of focal distance is subject to camera. In a range of 20-200mm, it will be displayed correctly. But an error may occur if out of this range. So also does if the range doesn’t comform to this flash. SYNC Mode ButtonSYNC FN button can set flash sync mode and FN function *settings individually. SYNC FN: gently press this button to set flash sync mode. *Press and hold this button to enter FN function setting. SYNC can set HSS, 1st curtain sync and 2nd curtain sync mode. Gently press this button to set HSS [ ], 1st curtain sync [ it won’t show the icon], 2nd curtain sync [ ]. Please select the sync mode as needed. Press and hold this button to enter Beep Setting, LCD Lighting Time Setting, AF-assist Beam Setting and Stand-by Time Setting. Beep SettingPress and hold to enter FN function setting, and then turn dial selector to turn on beep [ ] or turn off beep [ ], then press OK to confirm the settings.LCD Lighting Time SettingPress and hold to enter FN function setting, and then continuously press this button to move the setting icon to LCD Lighting Time Setting, and then turn dial selector to select LCD Lighting Time:[ ] means on all the time,[ ] means on for 5 sec,[ ] means on for 10 sec, [ ] means turn off the light,Press OK to confirm the settings.AF-assist Beam SettingAF-assist beam is mainly applied to low-light or low contrast shooting environment. Under this condition, theWireless Flash Mode:Optical Transmission Icon:Radio Transmission Icon:AF-assist BeamDial Selector-FUNC Selector ButtonWarning Component NameSpecificationsWireless Flash Control Operation IntroductionRadio Transmission Flash Function ParameterWireless Flash ControlLithium Battery Speedlite SYNC Mode ButtonLED light Switch of LED lightX900 speedlite supports optical transmission flash Optical Transmission ControlX900 is equipped with optical transmission flash control and radio transmission flash control function.[ ] Optical transmission mode;[ ] FSK2.4HzWireless Flash Control※ While controlling exposure compensation on X900 speedlite via camera flash setting menu, the exposure compensation value should set as 0 EV, or you may not be able to set camera exposure compensation. When flash LCD screen shows CAM, it means camera output exposure compensation. When flash LCD screen shows LAMP, it means flash output exposure compensation.X900 speedlite can control flash mode, output power, exposure compensation, FEB, focus, sync mode and other functions via camera flash settings menu. (Only for cameras equipped with flash setting menu)Support Camera External Flash Menu ControlUsing wide panel, flash coverage range will enlarge.When using, pull out the reflector with wide panel together, and push back reflector. Then you may use the wide panel. Wide PanelUsing the reflector enables you to reflect light in a person's eyes and create a more vivid expression.When using, pull out the reflector and wide panel together, and push back the wide panel. Then you may use the reflector.ReflectorBy pressing this button, the flash head can be adjusted to up/down and left/right. Up/down ward angle -7 to 90 degree,left/right angle 180 degree. PUSH Reflect Lock Release ButtonIt's applied to connect camera with SYNC cable or trigger flash. PC Port※ Mult frequency can set as 1-500 Hz. Frequency setting is subject to camera. Some cameras do not support higher frequency. ※ To avoid the damage of flash head due to overheating, do not use Mult flash shooting over 10 times. After 10 14 15 X900 speedlite is equipped with radio transmission flash function. With radio transmission, flash firing is less affected by obstacles, so its transmission and control efficiency are much higher. When using with Pixel King PRO and OPAS flash trigger, or among X900c,X800PROspeedlites (Master/Slave), you can use wirelesstransmission flash. Introduction of the functionThe remote flash must be set as slave mode*X900 slave mode X900 slave mode setting: After power-on, pressing the button “RMOT” for two times entering into SL mode.Slave ModePressing the “RMOT” button for a long time for two times and entering into the SL mode from the starting-up interface.King PRO master channel:：Channel IconX900 Slave channelX900 master mode channelMaster Channel:Slave ChannelThe icon of slave mode of 2.4GHz 1. The setting of communication channel※Set master mode in master mode channel, slave mode in slave mode channel.3：The setting of communication group※The 1-4 channel of King PRO correspond with the 1-4 channel of Speedlite.The LED light which equipped with X900 Speedlite is controlled by one switch separately with its own circuit design. It has no effect on Speedlite, one light can be used in many ways.LED LightIt's applied to upgrade the firmware. You can download the newest firmware from Pixel website. Website: www.pixelhk.com USB PortThe button of mode: gently pressing it, entering into master mode and slave mode.The icon of master mode of 2.4GHzKing PRO communication channel setting: After powered-on, gently pressing the second button on the upper right corner of the King pro （the button on the center) to enter into communication channel and choose setting function by pressing the first button on upper left corner that will show a "+" on screen and the second button that will show a "-" on the screen. Then, pressing button to choose "01" to "15" channels and pressing the first button on the lower left of the king pro that will show an "OK" on the screen.The communication channel setting of X900 Speedlite: Gently pressing the first button on the upper left corner of the flash that correspond to the button of "SET*RMO" on the lower left of Canon flash. When the indicator is on, entering into the communication channel setting and turning the round dial near the "OK" on the screen. You can choose the channel from "CH01" to "CH04" and press the button of "OK" to confirm.：Channel Icon：Channel IconThe communication group setting of King pro: After power on, gently pressing the three buttons of "A""B""C" separately. When the red light is on which represents the corresponded group control switch.The communication group setting of x900: In the master mode, repeatedly pressing the first button on upper left corner of the flash (correspond to the button of "SET*RMO" on the lower left of Canon flash).Moving the light icon to the communication group setting, you can turn the round dial near the button of "OK" and choose the channel you need to control and press the button of "OK"In the slave mode of flash, gently and repeatedly pressing the first button on the upper left corner of the flash (correspond to the button of "SET*RMO" on the lower left of Canon flash), moving the light icon into the communication group setting. At the time, turning the round dial on the OK button and choosing channels from "A" "B" "C" and pressing the OK button to confirm.King PRO GroupKing PRO Group Setting ButtonX900 Slave GroupSlave Groupx900 Slave GroupSlave Group：Group Icon：Channel IconOne year warranty from the day of purchase. Please kindly contact Pixel or distributor for more details.Thank you for using Pixel product and reading this instruction manual. If you have any questions, please contact your local dealer or visit http://www.pixelhk.comThe instruction manual is updated June 27, 2016. For information on the compatibility with accessories marketed after this date, please contact Pixel's dealer for advice. Warranty：King PRO Group Icon/ /16FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions:(1) This device may not cause harmful interference, and (2) Thisdevice must accept any interference received, includinginterference that may cause undesired operation.Warning: Changes or modifications not expressly approved by theparty responsible for compliance could void the user's authorityto operate the equipment.NOTE: This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one ormore of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Navigation menu