Pixel Technology X900C Speedlite User Manual 1
Shenzhen Pixel Technology Limited Speedlite 1
User Manual
12
unit is independent, without interference;
3. Under ALL mode, all of units will join in firing.
MULT Mode
1. A:B can set different flash output of group A and B
individually, except group C. The frequency and flash times
of group A and B are the same;
2. A:BC can set the flash output of group A, B, C. The flash
power of the three groups can be set separately. And the
frequency and flash times of the three groups are the same;
3. Under ALL mode, all of units will join in firing. The frequency
and flash times of every firing group are the same.
※ Under MULT mode of wireless flash, flash frequency can be set
between 1-199Hz.
Error Warning Prompt
When an error occurs on the flash or overheating protection is
activated, the following information will display on the screen:
Motor Error Prompt:
WARNING: MOTOR ERROR
Motor Error, Battery and Flash Head Overheating
Prompt:
WARNING: MOTOR ERROR BAT LAMP TEMPERATURE
Motor Error, Flash Head Overheating Prompt:
WARNING: MOTOR ERROR LAMP TEMPERATURE
Flash Head Overheating Prompt:
WARNING: LAMP TEMPERATURE
Battery Overheating Prompt:
WARNING: BATTER TEMPERATURE
Unknown Error Prompt:
WARNING: ERROR 90
※ When a prompt occurs on flash motor and unknown error, you are
advised to switch on-off the flash repeatedly to make it self-recovery.
After recovery, the prompt info will disappear, and you can reuse it. If
not, you are advised to contact the dealer for repair.
※ When you use the flash continually, flash head and battery overheating
protection will be activated, then the LCD display screen will shows
error prompt and restrict flash firing. Now please turn off the flash and
allow a rest time for reuse. Then the prompt info will disappear, and you
can reuse it.
-3- -4-
Dial Selector
This dial selector is applied to adjust setting parameter of
the flash. Turn left to reduce setting parameter, and turn
right to increase setting parameter.
Operation Interface
Introduction
X900 Speedlite is the newest one developed by Pixel which
has multifunction and fast recycle time. Featured with fast
recycle time, it can use Lithium battery, AA battery and can be
used with Pixel power bank TD-386 which has high power
capacity. When use lithium battery or power bank TD-386, the
recycle time is less than 1.5 sec, full power output is up to over
700 times that makes you cannot miss the amazing moment; It
has the configurations of HSS, high GN, wireless control,
stroboscopic and so on. The frequency of stroboscopic is up to
500 times, the performance is more strong and stable; In the
area of controlling Speedlite, beside the optical control, it
imports wireless control system FSK2.4GHz and supports the
direct wireless control between King PRO, Speedlite and
Speedlite making the match between speedlites more free.
X900 Speedlite ingeniously adopts 4 watt full white light LED
creative set light, LCD lattice screen with high definition,multi-
matrix overheat warning system and other thoughtful
equipment. It is a Speedlith with high performance,
multifunction and multipurpose. Beside that, users can
upgrade firmware through Mini port to enjoy official and
thoughtful services from Pixel.
In 1st Curtain mode
the icon don`t show
FUNC Selector Icon
SYNC Mode Icon
13
X900 master mode
King pro master mode
The gear installed on the camera must be set as master mode:
1. Communication mode settin
Introduction of operation
The master mode setting of King Pro: After power-on, gently
pressing the right first button on the king pro installed on the
camera, entering into the setting of master mode and slave
mode to set the mode by pressing the left first button that will be
display a “+” on the screen and the second button that will
display a “-” on the screen. Then, pressing the first left button
that will display an “OK” on the screen.
The master/slave mode setting of X900: you can enter into the
master mod by pressing the first upper left button on flash for a
long time (the button of “RMOT”) and choose FSK2.4GHz
wireless mode as flash mode. [ ]
Both Wireless trigger King pro and x900 pro have FSK2.4GHz
wireless control mode, and X900 Speedlite has a built-in
wireless receiver; When used with king pro, the x900 pro flash
can be controlled without Receiver and all kinds of flash modes
can be controlled by king pro, for example: TTL, M, focal
length, exposure compensation and so on；At the same time,
two flashes can be used in wireless flash mode through 2.4GHz
communication without any trigger. (Beside FSK2.4GHz mode,
x900 pro has optical mode. The introduction is about the
operation mode of FSK2.4GHz)
The introduction of the operation of Pixel
Wireless Trigger King PRO and X900 Speedlite
wireless control.
Please make sure the communication mode, channel and group
of king pro and x800 pro are correct, otherwise they cannot
communicate and be used normally.The king pro and x800 pro
installed on the end of camera should be set as master mode,
the off-camera flash should be set as slave mode; then, the
group of master mode and slave mode and the channel should
be set as the same.
Pressing the button of “RMOT” for
a long time, you can enter into the
maser mode.
control function. The speedlite mounted on the camera
can transmit signal via optical pulse to control firing
re m o t e ly. Wh e n u sin g w irel e s s fl a s h mo d e , th e
speedlite mounted on the camera should set as Master
mode, and the off-camera flash set as Slave mode.
Optical transmis-sion flash is achieved by optical pulse,
not wireless signal transmission, so the transmission
distance is very short. Please note the following issues
when using:
1. Make sure the slave unit within effective control range
when using optical transmission flash mode;
2. The receiving signal sensor of slave unit should face to
master unit;
3. You are required to use flashes that are equipped with
an optical transmission wireless shooting function;
4. Please do not place any obstacles between the master
unit and salve unit when using optical transmission
flash mode, or it may affect optical signal transmission;
5. Under optical transmission flash mode, use ETTL flash
and M flash support high speed sync (HSS) and 1st
curtain sync. When using MULT flash, it supports 1st
curtain sync.
Optical Transmission Flash Function Parameter
Transmission Method: Optical pulse
Mode Control: Master/Slave,S1/S2
Channel Control: 1-4 channels
Group Control: 3 groups (A/B/C)
Transmission Distance: about 0.7-10m
Horizontal: ±40°; Vertical: ±30° (facing to master unit)
Flash Ratio Control: 1:8-1:1-8:1
Sync Mode: HSS, 1st curtain sync
Optical Transmission Flash Control Operation Introduction
Press and hold RMOT button to enter wireless flash
*
master mode; after entered wireless flash mode, press
and hold SET RMOT button to enter wireless flash Slave
mode. Press and hold again to exit wireless flash mode.
Optical Transmission mode can set Master/Slave group
control, channel control, Master flash On/Off.
1. Master/Slave Mode Setting
Master Mode Setting: press and hold RMOT button to
*
enter wireless flash control mode. Gently press this
button again and then turn dial selector to select optical
transmission mode[ ] . If this mode is already
displayed after entered wireless flash control interface,
then there is no need to make setting. When using
optical transmission flash, the speedlite mounted on the
camera should set as this mode.
Slave Mode Setting: after entered wireless flash mode,
press and hold SET RMOT to enter Slave mode [SL].
*
Gently press SET RMOT button again and then turn dial
*
selector to select Slave optical transmission mode [ ] .
If this mode is already displayed on the interface after
entered slave mode, then there is no need to make
setting.
2. Group Control Setting
After entered wireless flash Master mode, continuous
Manufacturer: Shenzhen Pixel Technology Limited
Address: Rm1411, AAA Building, Renmin Road, Longhua
District, Shenzhen City.
TEL: 400-8084899
Website: www. Pixelhk.com.cn
Product Standard: Q/PSKJ004-2016
8
17
PSM V10.01154177
6
built-in AF-assist beam activates automatically to help
autofocus.
Press and hold to enter FN function setting, and then
continuously press this button to move the setting icon to
AF-assist Beam Setting, and then turn dial selector to turn
on AF [ ] or turn off AF [ ]. Press OK to confirm the
settings.
Stand-by Time Setting
Press and hold to enter FN function setting, and then
continuously press this button to move the setting icon to
Stand-by Time Setting, and then turn dial selector to select
stand-by time:
[ ] means 5mins stand-by time,
[ ] means 10mins stand-by time,
[ ] means 30mins stand-by time,
[ ] means 1hr stand-by time,
[ ] means 2hrs stand-by time,
[ ] means 4hrs stand-by time,
[ ] means non-sleep mode.
Press OK to confirm the settings. When under wireless
Slave mode, the default stand-by time as 1 hour.
When flash entered sleep mode, the flash display screen
will show [ ] icon. Half-press camera shutter or Flash
Test Button to wake up the flash.
LOCK
It's applied to lock the parameter settings of the flash,
avoiding the flash parameter may be changed accidently.
MODE
Flash mode button. It's applied to set the flash mode. You
can set the flash mode to ETTL full auto flash, Manual
flash and Mult flash mode individually. Press and hold this
button to reset your flash to the original factory settings.
ETTL
ETTL Flash Mode. The camera and flash metering system
will work together to make correct exposure, thus the
sh oot ing subject and background wil l ge t balanced
exposure. Under this mode, it's available to set the EV and
FEB. The EV and FEB adjustable power is between
-3.0EV to + 3.0EV in 1/3 increments.
M
Manual Flash Mode. You can set the flash output from
1/128 power to 1/1 full output in 1/3 increments. Set flash
output power with dial selector. Turn left to reduce setting
parameter, and turn right to increase setting parameter.
MULT
Mult Flash Mode. Mult flash mode can make one image
displays as a serial continuous moving image. Under Mult
flash mode, you can set flash output power, flash times
and flash frequency.
9
press SET RMOT button, and then move setting icon to
*
Group Control Setting [ ALL], then turn dial selector to
select the group as needed.
Master Group Mode Switch: ALL→A→:B→A:BC
Slave Group Mode Switch: A→B→C
3. Flash Channel Setting
After entered wireless flash Master mode, continuous
press SET RMOT button, and then move setting icon to
*
Channel Setting [CH1], then turn dial selector to select
flash channel. Optional channel: CH1-CH4, 4 channels
in total. Slave flash channel need to set in the slave
interface, the method is the same as master channel
setting.
If the transmission channels of the master unit and slave
unit are different, then the slave unit won't fire. Both
Master and slave must be set to the same channel.
4. Master Flash On/Off Setting
After entered wireless flash Master mode, continuous
press SET RMOT button, and then move setting icon to
*
Master Flash On/Off [ ] , then turn dial selector to
select Master Flash On[ ] or Off [ ] .
When flash is On, master flash will join in exposure.
When flash is Off, master flash will not join in exposure.
※ Under Slave mode, it's not available to set flash On/Off. Here
flash is On by default.
※When using optical transmission function and the Master flash set
as OFF, the Master flash may join in exposure under low sync
speed according to optical pulse transmission theory.
ETTL Mode
Unde r E T TL m o de, you can s e t g roup fla s h r atio,
ALL→A:B→A:BC.
1. A:B can set the flash ratio of group A ,B;
2. A:BC can set the flash ratio of group A, B. Under this
mode , group C is in dependent which c an be set
individually;
3. Under ALL mode, all of units will join in firing.
※ If need more flash output, you can invite the numbers of the slave
unit which is unlimited.
M Mode
Under manual wireless flash mode, the Master unit can set
different flash output for every slave flash (every
group).
1. A:B can set the flash output of group A ,B, except group
C;
2. A:BC can set the flash output of group A, B, C. Each
group unit is independent, without interference.
3. Under ALL mode, all of units will join in firing.
MULT Mode
1. A:B can set different flash output of group A and B
individually, except group C. The frequency and flash
times of group A and B are the same;
2. A:BC can set the flash output of group A, B, C. The flash
power of the three groups can be set separately. And the
frequency and flash times of the three groups are the same;
11
1. Master/Slave Mode Setting
Master Mode Setting: press and hold RMOT button to
*
enter wireless flash control mode. Gently press this button
again and then turn dial selector to select radio transmission
mode[ ]. If this mode is already displayed after entered
wireless flash control interface, then there is no need to
make setting. When using wireless flash, the speedlite
mounted on the camera set as this mode.
Slave Mode Setting: after entered wireless flash mode,
press and hold SET RMOT button to enter Slave mode
*
[SL]. Gently press this button again and then turn dial
selector to select Slave optical transmission mode[ ].
If this mode is already displayed on the interface after
ente red slave mode, then there is n o need to make
setting.
2. Group Control Setting
After entered wireless flash Master mode, continuous
press SET RMOT button, move setting icon to Group
*
Control Setting [ ALL], then turn dial selector to select
the group as needed.
Master Group Mode Switch: ALL→A:B→A:BC
Slave Group Mode Switch: A→B→C
3. Flash Channel Setting
After entered wireless flash Master mode, continuous
press SET RMOT button, and then move setting icon to
*
Channel Setting [CH1], then turn dial selector to select
channel. Optional channel: CH1-CH15,15 channels in
total. Slave flash channel need to set in the slave
interface, the method is the same as master channel
setting. If the transmission channels of the master unit
and slave unit are different, then the slave unit won't
fire. Both Master and slave must be set to the same
channel.
4. Master Flash On/Off Setting
After entered wireless flash Master mode, continuous
press SET RMOT button, and then move setting icon to
*
Master Flash On/Off[ ], then turn dial selector to
select Master Flash On [ ] or Off [ ].
※ Under Slave mode, it's not available to set flash On/Off. Here the
flash is On by default.
ETTL Mode
Unde r E T TL m o de, you can s e t g roup fla s h r atio,
ALL→A:B→A:BC.
1. A:B can set the flash ratio of group A ,B;
2. A:BC can set the flash ratio of group A, B. Under this
mode , group C is in dependent which c an be set
individually;
3. Under ALL mode, all of units will join in firing.
※ If need more flash output, you can invite the numbers of the slave
unit which is unlimited.
M Mode
Under manual wireless flash mode, the Master unit can set
different flash output for every slave flash (every group).
1. A:B can set the flash output of group A ,B, except group C;
2. A:BC can set the flash output of group A, B, C. Each group
10
3. Under ALL mode, all of units will join in firing. The
frequency and flash times of every firing group are the
same.
※ Under MULT mode of optical transmission flash, flash frequency
can be set between 1-199Hz.
※ Opt ical trans mis sion is ach iev ed by optical p ulse, s o its
transmission performance is not so good and transmission
distance is short. For better use wireless flash function, we are
advised to use wireless flash mode. Being less affected by
obstacles, wireless signal transmission and control efficiency are
much higher.
S1/S2 Optical Control Mode
S1 Manual Optical Transmission Mode: when set flash
as this mode, it can work with the first firing of the Master
flash synchronously. Set Master flash as manual M mode.
The ETTL or MULT mode cannot be fired.
S2 ETTL Optical Transmission Mode: when set flash as
this mode, it can fire with the ETTL mode of the Master
flash synchronously. Set Master flash as ETTL auto
metering mode. The M or MULT mode cannot be fired.
1. After entered optical Slave Mode (SL), gently press
MODE FN button and then turn dial selector to select
*
MODE S1 or MODE S2 mode.
2. Under Slave MODE S1 or MODE S2 mode, press +/- and
then turn dial selector to adjust the output power of
Slave Flash.
※ MODE FN: namely gently press Slave mode, press and hold to
*
enter FN function setting.
※The X900 wireless flash (2.4GHz) system is not compatible with
that of Canon original flash. It can only be compatible with part of
Pixel wireless products.
Transmission Method: FSK2.4GHz
Mode Control: Master/Slave
Channel Control: 1-15 channels
Group Control: 3 groups (A/B/C)
Transmission Distance: about 50M
Flash Ratio Control: 1:8-1:1-8:1
Sync Mode: HSS, 1st curtain sync
Wireless flash control can set Master/Slave group control,
channel control, Master flash On/Off.
7
※continuous flashes, allow a rest time of the flash at least
15mins.
※If you fire more than 10 continuous flashes, the safety
function may activate and restrict flash firing. If this
happens, please allow a rest time of the flash at least
15mins.
● Do not expose this product in high temperature location or
confined spaces exposed to strong direct sunlight and other
overheating places.
● Keep it dry. Do not touch this product with wet hand.
Do not expose this product to water or rain, or you may not
be able to use it.
● Do not use it in inflammable gas, or it may cause explosion
or fire.
● This product involved in battery. Please strictly follow the
corresponding operations related to battery, or it may cause
explosion or fire.
● Do not put the component in strong vibration, or it may
cause fault of this product.
● Remove the batteries during long periods of non-use.
● Do not use the flash light in a short distance from the eyes,
or it may cause possible injury to eyes or blindness.
● After continuous use, it will be very hot. Do not touch, or it
may cause burn.
● After continuous use, the battery might be hot. Please be
careful when changing new battery.
● Do not disassemble or maintain this product by yourself.
The internal high voltage will cause electric shock.
●Only the same brand and battery type can be used.
12
GN: 60 (ISO100 200mm)
Flash Coverage Range:
20 -200mm
Auto Zoom: According to shooting angle and image to auto adjust the
coverage range
Manual Zoom:
According to camera or flash setting to adjust the zoom range
Flash Mode: ETTL/M/MULT
Stroboscopic Flash:
1-500Hz
Wireless Flash:
Radio transmission/ Optical transmission
support Master/ Slave, S1/S2
SYNC Mode: High Speed Sync, 1st Curtain Sync, 2nd Curtain Sync
Adjustable Angle:
Up/down: -7/90 degree Left / Right: 180 degree/180 degree
Manual Flash: 1/128-1/1 output control (1/3rd increments)
Recycle Time: Less than 2.5 sec (1/1 full power output)
LCD Display Screen:
High definition dot matrix screen
Internal Power Source:
4×AA size alkaline batteries or rechargeable batteries (4×1.5V)
External Interface: Hot shoe, PC port, USB port, external power port
EV: In 1/3rd increments (±3 stops)
FEB: In 1/3rd increments (±3 stops)
Battery Life: 180 times (1/1 flash output, with Sanyo Eneloop batteries)
Fluorescent tube: Ultra-long battery life design
Overheating Warning:
Multi dot matrix temperature control, battery
overheating warning
AF-Assist Beam:
Firmware Upgrade: Support
Dimension: 73.50mm×61.00mm×192.00mm
Weight: 420.00g (excluding batteries)
Support
Instruction Manual
English
For Canon
X900 C
5
RMOT Wireless Flash Button
*
Press and hold this button to enter wireless control mode.
The wireless mode and optical transmission mode can be
set individually. First, press and hold this button to enter
wireless flash mode; and then press and hold this button
again to enter Slave mode; and press and hold once again
to exit wireless flash mode.
SET RMOT: namely gently press to set SET function.
*
Press and hold this button to enter next function.
With mark function button means press and hold this
*
button to enter the corresponding function setting.
-/+ Function Button
This function button is applied to adjust output parameter
of the flash, FEB and other functions. Function adjustment
alters from shooting mode. It's subject to image display
function. FEB, namely flash exposure bracket. When
displaying FEB, you may set flash exposure bracket.
ZOOM
This Zoom button is applied to set Zoom mode. Zoom
mode includes manual zoom [ ] and auto zoom [ ].
Set this function with dial selector.
※ Focal distance can set as 20-200mm. Some cameras do not
support higher focal distance. The setting of focal distance is
subject to camera. In a range of 20-200mm, it will be displayed
correctly. But an error may occur if out of this range. So also does
if the range doesn’t comform to this flash.
SYNC Mode Button
SYNC FN button can set flash sync mode and FN function
*
settings individually.
SYNC FN: gently press this button to set flash sync mode.
*
Press and hold this button to enter FN function setting.
SYNC can set HSS, 1st curtain sync and 2nd curtain sync
mode. Gently press this button to set HSS [ ], 1st curtain
sync [ it won’t show the icon], 2nd curtain sync [ ]. Please
select the sync mode as needed. Press and hold this
button to enter Beep Setting, LCD Lighting Time Setting,
AF-assist Beam Setting and Stand-by Time Setting.
Beep Setting
Press and hold to enter FN function setting, and then turn
dial selector to turn on beep [ ] or turn off beep [ ],
then press OK to confirm the settings.
LCD Lighting Time Setting
Press and hold to enter FN function setting, and then
continuously press this button to move the setting icon to
LCD Lighting Time Setting, and then turn dial selector to
select LCD Lighting Time:
[ ] means on all the time,
[ ] means on for 5 sec,
[ ] means on for 10 sec,
[ ] means turn off the light,
Press OK to confirm the settings.
AF-assist Beam Setting
AF-assist beam is mainly applied to low-light or low
contrast shooting environment. Under this condition, the
Wireless Flash Mode:
Optical Transmission
Icon:
Radio Transmission
Icon:
AF-assist Beam
Dial Selector
-
FUNC Selector Button
Warning Component Name
Specifications
Wireless Flash Control Operation Introduction
Radio Transmission Flash Function Parameter
Wireless Flash Control
Lithium Battery Speedlite
SYNC Mode Button
LED light Switch of LED light
X900 speedlite supports optical transmission flash
Optical Transmission Control
X900 is equipped with optical transmission flash
control and radio transmission flash control function.
[ ] Optical transmission mode;
[ ] FSK2.4Hz
Wireless Flash Control
※ While controlling exposure compensation on X900 speedlite via
camera flash setting menu, the exposure compensation value
should set as 0 EV, or you may not be able to set camera exposure
compensation. When flash LCD screen shows CAM, it means
camera output exposure compensation. When flash LCD screen
shows LAMP, it means flash output exposure compensation.
X900 speedlite can control flash mode, output power,
exposure compensation, FEB, focus, sync mode and
other functions via camera flash settings menu. (Only for
cameras equipped with flash setting menu)
Support Camera External Flash Menu Control
Using wide panel, flash coverage range will enlarge.
When using, pull out the reflector with wide panel together,
and push back reflector. Then you may use the wide panel.
Wide Panel
Using the reflector enables you to reflect light in a person's
eyes and create a more vivid expression.
When using, pull out the reflector and wide panel together, and
push back the wide panel. Then you may use the reflector.
Reflector
By pressing this button, the flash head can be adjusted to
up/down and left/right. Up/down ward angle -7 to 90 degree,
left/right angle 180 degree.
PUSH Reflect Lock Release Button
It's applied to connect camera with SYNC cable or trigger flash.
PC Port
※ Mult frequency can set as 1-500 Hz. Frequency setting is subject
to camera. Some cameras do not support higher frequency.
※ To avoid the damage of flash head due to overheating, do
not use Mult flash shooting over 10 times. After 10
14 15
X900 speedlite is equipped with radio transmission flash
function. With radio transmission, flash firing is less
affected by obstacles, so its transmission and control
efficiency are much higher. When using with Pixel King
PRO and OPAS flash trigger, or among X900c,X800PRO
speedlites (Master/Slave), you can use wireless
transmission flash.
Introduction of the function
The remote flash must be set as slave mode
*
X900 slave mode
X900 slave mode setting: After power-on, pressing the
button “RMOT” for two times entering into SL mode.
Slave Mode
Pressing the “RMOT” button for a long
time for two times and entering into the
SL mode from the starting-up interface.
King PRO master channel:
：Channel Icon
X900 Slave channel
X900 master mode channel
Master Channel:
Slave Channel
The icon of slave mode of 2.4GHz
1. The setting of communication channel
※Set master mode in master mode channel, slave mode in
slave mode channel.
3：The setting of communication group
※The 1-4 channel of King PRO correspond with the 1-4
channel of Speedlite.
The LED light which equipped with X900 Speedlite is controlled
by one switch separately with its own circuit design. It has no
effect on Speedlite, one light can be used in many ways.
LED Light
It's applied to upgrade the firmware. You can download the
newest firmware from Pixel website. Website: www.pixelhk.com
USB Port
The button of mode:
gently pressing it,
entering into master
mode and slave mode.
The icon of master mode of
2.4GHz
King PRO communication channel setting: After powered-on,
gently pressing the second button on the upper right corner of
the King pro （the button on the center) to enter into
communication channel and choose setting function by
pressing the first button on upper left corner that will show a "+"
on screen and the second button that will show a "-" on the
screen. Then, pressing button to choose "01" to "15" channels
and pressing the first button on the lower left of the king pro that
will show an "OK" on the screen.
The communication channel setting of X900 Speedlite: Gently
pressing the first button on the upper left corner of the flash that
correspond to the button of "SET*RMO" on the lower left of
Canon flash. When the indicator is on, entering into the
communication channel setting and turning the round dial near
the "OK" on the screen. You can choose the channel from
"CH01" to "CH04" and press the button of "OK" to confirm.
：Channel Icon
：Channel Icon
The communication group setting of King pro: After power on,
gently pressing the three buttons of "A""B""C" separately. When
the red light is on which represents the corresponded group
control switch.
The communication group setting of x900: In the master mode,
repeatedly pressing the first button on upper left corner of the
flash (correspond to the button of "SET*RMO" on the lower left
of Canon flash).Moving the light icon to the communication
group setting, you can turn the round dial near the button of
"OK" and choose the channel you need to control and press
the button of "OK"
In the slave mode of flash, gently and repeatedly pressing the
first button on the upper left corner of the flash (correspond to
the button of "SET*RMO" on the lower left of Canon flash),
moving the light icon into the communication group setting. At
the time, turning the round dial on the OK button and choosing
channels from "A" "B" "C" and pressing the OK button to
confirm.
King PRO Group
King PRO Group Setting Button
X900 Slave Group
Slave Group
x900 Slave Group
Slave Group
：Group Icon
：Channel Icon
One year warranty from the day of purchase. Please kindly
contact Pixel or distributor for more details.
Thank you for using Pixel product and reading this
instruction manual. If you have any questions, please
contact your local dealer or visit http://www.pixelhk.com
The instruction manual is updated June 27, 2016. For
information on the compatibility with accessories
marketed after this date, please contact Pixel's dealer for
advice.
Warranty
：King PRO Group Icon
/ /
16
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.