Planex Communications BT-06HS-T Bluetooth headset User Manual

Planex Communications inc. Bluetooth headset Users Manual

Users Manual

LL6. How to wear it firmly7. Make a call.To make a call, dial through your mobile phone.8. Reject a call. Touch 2 SecIf you can't wear it firmly, use the ear hook as assist---------- ----------microphone toward jaw---------- Left-ear use Right-ear use11. Voice dialing12. Redial last number13. Volume control.1.When you have a incoming call just “touch” the Talk key ,after you hear the ring from the headset.2.You can also click MFB key to receiving a callWhen you finish a call; touch the Talk key 1 Sec. ----end the call. 10. End a call.Click Double-Click Touch 1 Sec----------You can adjust the headset volume during a call.9. Answer a call. Mute & un-muteTouch ---------- --------------------1.When during call press the “ Volume up & Down" key ; you will hear a “ Do-lu-do-do" sound, then your voice won't be heard.2.Click the Volume up or Volume Down key again, you will hear the " Beep " sound to un-mute the microphone.simultaneously1.The headset should be under "Connected mode". By double-click the MFB key, after you hear a " Do- Do " sound from the headset, then it will redial again.2.This function depends on the specification of your mobile phone.1.The headset should be under "Connected mode", click the MFB key; then you can make the " Voice dialing " by the mobile phone's operation instruction..2.This function depends on the specification of your mobile phone.When you hear the in-coming call rings from your headset;touch the Talk key touch panel(logo area)for 2 Sec, when you hear the " Do Do" sound than release it. ---Reject a call.Inserted completelyCap the ear tipXParallelThe salient insert in the little hole X Inserted Incompletely Inserted Incompletely Inserted IncompletelyThe ear tip must insert to ear bone completely.Ringing.....Ringing.....3. Turn on/ Turn off4. Pairing with your mobile phone It need to pair with your Bluetooth device, first time.5. How to wear the headset4. "BT-06HS-T” will show on certain items in your mobile phone.5. Key in pairing pin code "0000”press " yes" , the indicator light will turn from the blue/red flashing status into blue flashing, it means the pairing has been successful.7.Now the headset has been in the "connected mode". you may receive or dial the phone call.5 Sec- Stand-by mode------- blue light flash once every 5 Sec.- Cblue light flash two times every 5 Sec.- Active call mode----- blue light flash three times every 5 Sec.- low battery----- red light flash. onnected mode---- Choose the ear tip sizeChoose the ear plug sizePower on - blue light flashing. Power off - red light flashing then off.Red blue1.Before pairing, make sure your headset is off.2.Press the MFB key for at least 5 sec; the blue and red light flashing alternately it means the headset is in the “pairing mode".3.Please ensure that your mobile phone is provided the Bluetooth Function, and activate the function.3 SecPress the MFB key for about 3 Sec, to turn on and turn off.10cm~1mThe pairing distance Devices foundBT-06HS-Tlarge one on headset alreadyOver 7 .Over 7 Day Within 90 ~120Mins.10 meters(open space)Handsfree / Headset .Bluetooth V2.1hrss.0 ~ 55 'C0% ~ 90% (non-concrete status)5V DC, 00~240V AC adapterSpecification of the Headset1. Charging the Headset 1. At least for 4 hours when first time charging,2. When charging, the red light on; fully charged the light will be off.2. Introduction of the product Bluetooth HeadsetUser Manual BT-06HS-TBluetooth StandardTalktimeStandby timeCharging timeSupported Bluetooth profilesOperating temperature rangeStorage temperatureOperation rangePower SupplyUSB PortCharging Plug light indicator(logo area) Volume up MFB /Volume down Speaker Ear tipEar plug Hook pointCharging PortMicrophoneTalk key touch panelModel: BT-06HS-TFCC ID. : SJ9-BT-06HS-TTHIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIONS IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCERECEIVED, INCLUDING INTERFEERENCE THAT MAY UNDESIRED OPERATION.Made in Taiwan Brand Name:PCIUser guide
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

Navigation menu