Polygroup 1701 Remote controller User Manual TG76P4812L02 new

Polygroup Limited(Macao Commercial Offshore) Remote controller TG76P4812L02 new

Contents

User Manual

ASSEMBLY INSTRUCTIONS MADE IN CHINA GROW & STOW™CHRISTMAS TREEIMPORTANT SAFETY INSTRUCTIONSWhen using electrical products, basic precautions should always be followed including the following:a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.c) This seasonal use product is not intended for permanent installation or use.d) Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.f) Do not let lamps rest on the supply cord or on any wire.g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.h) This is an electric product-not a toy! To avoid risk of fire burns, personal injury and electric shock it should not be played with or placed where small children can reach it.i) Do not use this product for other than its intended use.j) Do not hang ornaments or other objects from cord, wire, or light string.k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.l) Do not cover the product with cloth, paper or any material not part of the product when in use.m) This product is equipped with push-in type lamps. Do not twist lamps.n) Read and follow all instructions that are on the product or provided with the product.o) SAVE THESE INSTRUCTIONS
ASSEMBLY INSTRUCTIONS MADE IN CHINA2PRODUCT SPECIFICATIONDescriptionAccessories Included: Grow and Stow tree is an indoor Christmas Tree provided with a electromechanical system for multiple height adjustment. Powered by a switching power supply (adaptor), It can be control by a foot pedal and a RF remote control unit. This controller commands the mechanism for stow and deploy, as well as the lighting functions. The full lower section of the motorized tree is provided with quick set connectors, and this entire tree easily storages within a compact bag for convenient storage.Foot Pedal, Remote hand set, adaptor, power cord, owner manualSwitching Power Supply (adaptor):Input AC110-240V, 50/60Hz, Output DC 29V/2A7.5ft Tree Grow Range (Vertical Stroke):Minimum: 6ftMaximum: 7.5ftStroke: 1.5ft9ft Tree Grow Range (Vertical Stroke):Minimum: 7ftMaximum 9ftStroke: 2ftTree Life Cycle:3000 Cycles Max.Remote Controller Range:33 ft (10m) Remote Controller PowerDC 3V Operational Temperature:0oC to 40oC, 85% Humidity, indoor useStorage Temperature:-5oC to 60oC, 85% HumidityUse and Care Instructionsa) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections or exposed copper wire.b) When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.c) When not in use, store neatly in a cool, dry location protected from sunlight.USER SERVICNG INSTRUCTIONSLamp Replacement:Step 2: Lift up to unsnap lockingtab, then pull lamp and plastic base straight out of lampholder.Step 1: Grasp plug and remove from thereceptacle or other outlet device. Do notunplug by pulling on cord.Step 3: Replace lampwith only 3.6 Volt, 0.072 watt or 2.4 Volt,0.048 Watt LED type lamps provided with this product.(Reference figure only)If the new lamp base does not fit in lamp holder, follow the step below before Step 3.a) Remove the base or burned out lamp by straightening lamp leads and gently pull lamp out.b) Thread leads of new lamp through holes in old base with one lead in each hole.c) After lamp is fully inserted into base, bend each lead up, like other lamps in the light set so that the leads will touch the contacts inside the lampholder.CAUTION: 1. Risk of fire. This product dose not contain lamp shunts, which allow the product to operate if one lamp burns out.Replace lamps only with the spare lamps provided wiht this product.2. To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and b) Do not mount or support strings in a manner that can cut or damage wire insulation .
ASSEMBLY INSTRUCTIONS MADE IN CHINA3Grow And Stow Tree Part TableDrawingNo. Description Qty1 AC Power Cord 12 AC/DC Power Adaptor 13 Adaptor AC input jacks4 Adaptor DC output jacks5 Tree trunk base 16 Tree control male 4 pin connector, to foot pedal 17 Light string male 2 pin connector, to foot pedal 18 Tree stand with fixed wheels and swiveling casters 19 Caster locks10 Tree foliage, lower section11 Light strings connectors set 112 Quick set guide funnel and female socket 113 Quick set male connector14 Tree top section 1Key Description Qty15 Foot Pedal unit 116 Foot pedal - Light Functions Push button17 Foot pedal - Grow / Pause/ Stow Push button18 Foot pedal - Safety Lock Switch19 Foot pedal - 2pin male connector to power adaptor DC jack20 Foot pedal - 4pin female connector to tree control21 Foot pedal - 2pin female connector to light stringKey Description Qty22 Remote Control handset 123 Remote LED indicator24 Remote light functions button25 Remote grow (Up and Pause) button26 Remote stow (Down and Pause) button27 Remote battery compartment and lidKey Description QtyTree bag/pouch - Accessories (small) 1Tree bag - tree head 1Tree bag - tree Main 1
ASSEMBLY INSTRUCTIONS MADE IN CHINA4Main Diagram14131210202121341716181915115776689232425262227
ASSEMBLY INSTRUCTIONS MADE IN CHINA5Unpack Carton box Tree Assembly1.1 Place the tree box on an upright position (long side along the vertical direction). See the arrows marked on the box for reference. 1.2 Untie the wrap string around the carton box, knife or cutter may be required (not included).1.3 Pull up the top carton cover by the side hole handles (one on each side of carton box).1.4 Remove the tree head section out of the box and open the tree head bag.1.5 Remove the foam pads under the front wheels of the stand (swiveling casters Fig 1). The hard board under the stand will tip down creating a slight slope.1.6 Pull the tree out of the carton box carefully.1.7 Unlock the buckles on the tree bag, and loose the tree bag rope.1.8 Open the tree bag wide and pull it up from the top of the tree.2.1 Open and remove the protective cap from the top of the funnel guide before inserting the tree top section .2.2 Inserts the tree top section into top funnel gide of main section (see Fig 2)Wire ConnectionFig 312 1412143.1 All accessories are stored in a small pouch , attached near the tree wheel stand. Open the pouch and put all accessories ready for use. (all wires display as seen on g 3)3.2 Connect the 2pin and 4pin connectors coming from the base of the tree to their counterpart connectors on the foot pedal (As shown on g. 3). Make sure to lock them by turning the sockets.3.3 Plug the pedal 2 pin connector into the DC Power Adaptor output jack .Turn and lock with the socket.3.4 Plug the Power adaptor AC cord into an AC outlet. 3.5 The tree is energized and ready to be operated.19 4128SET UP INSTRUCTION1.1 1.21.3 1.41.5 1.61.7 1.8PULL HEREPULL HEREPULL HEREFig 1Fig 212
ASSEMBLY INSTRUCTIONS MADE IN CHINA6Tree Operation by Foot Pedal (Fig 4)Fig 44.1 Double check all connections are properly and securely done (see g 3), and make sure the lock switch is on "unlock" position .4.2 Push the tree logo button on foot pedal to start toggling between Grow, Pause, and Stow functions.4.3 Push the light button on foot pedal to navigate the light string functions.4.4 Note: If your foot pedal is 3 ashing mode model, your remote handset can control light ash with 3 kind modes (clear steady, multi steady , clear multi alternating ) If your foot pedal is the 8 ashing modes model, your tree will cycle between 8 ashing modes (clear multi fading, clear fading, clear multi alternating, steady clear, clear multi slow fading, multi steady , multi fading, and combination ) If your foot pedal is the 10 ashing modes model, your tree will cycle between 10 ashing modes (clear steady/ clear fading/ multi steady/ multi fading/ clear multi fading/ clear multi alternating / pastel steady/ pastel fading/ clear pastel multi alternating/ clear pastel multi fading)4.5 Slide lock switch on foot pedal to function lock or unlock. Grow and stow function is lock for foot pedal and remote when in "lock" position. Tree Shaping and Final Touches5.1 After growing the tree to a desired height, allow all branches to fall into place. Additionally, gently pull them up and out until in place. For aesthetical purposes, make sure that all branches are tilted down and unfolded.5.2 Continue to shape up the branches and tips working form the top down. Start with tips farthest from the trunk, and move towards the inner ones.5.3 After shaping the entire tree as previously recommended, slightly upsweep all branch tips for a uniform look. Shift branches to ll any gaps. Your Christmas tree is now complete and ready to be decorated. NOTE: It is highly recommended to operate the grow and stow functions ONLY when the tree is free of any ornament or decoration.191818171620 21Remote Hand Set Batteries Installation6.1 Remove the battery lid at the back of remote control, install the two AAA/UM4/LR03 batteries( not included) properly as indicated on the battery compartment. Make sure to match the (+) and (-) ends of the batteries . (see g 5)6.2 Buttons on the remote handset buttons are non-functional when the foot pedal lock switch is set to "lock" position. Make sure the switch is set to "unlock" position. (see Fig 4)6.3 Press light mode button to navigate the light functions. Note: If your foot pedal is 3 ashing mode model, your remote handset can control light ash with 3 kind modes (clear steady, multi steady , clear multi alternating ) If your foot pedal is the 8 ashing modes model, your tree will cycle between 8 ashing modes (clear multi fading, clear fading, clear multi alternating, steady clear, clear multi slow fading, multi steady, multi fading, and combination ) If your foot pedal is the 10 ashing modes model, your tree will cycle between 10 ashing modes (clear steady/ clear fading/ multi steady/ multi fading/ clear multi fading/ clear multi alternating / pastel steady/ pastel fading/ clear pastel multi alternating/ clear pastel multi fading)6.4 Press UP button on remote hand set to control tree Grow or Pause functions (toggle).6.5 Press DOWN button on remote to controls Stow or Pause functions (toggle).Fig 52724252618
ASSEMBLY INSTRUCTIONS MADE IN CHINA7Storage Instructions7.1 IMPORTANT: Remove all ornaments and decorations.7.2 Set the Grow and Stow tree to its minimum size. (g 6)7.3 Detach the AC power cord from AC outlet, and put all accessories parts into the accessories stow pouch . 7.4 Collect all wires, controllers and accessories inside the stow pouch. And attach it to the trunk near wheel stand . (Recommended)7.5 Remove the tree top section from top funnel guide. Fold all branches towards the pole and stow it inside the tree top bag .7.6 Gently fold up main section branches if needed.7.7 Place the main tree bag around the tree main section, warping the tree from top to bottom. Zip it until fully closed.7.8 Cinch tight the nylon rope on the bottom side of the main tree bag, the strap will hold its position once you release the spring clamp.7.9 Buckle the straps until you hear a rm click. Then cinch the straps tightly by pulling at the end of the loose strap.7.10 When not in use, store the tree in a cool, dry place away from sunlight. Exposing the tree to excessive heat or humidity may damage the tree.Fig 6REPLACEMENT PARTS ORDERING INFORMATIONNo DESCRIPTIONDrawingNo.PART No. qty1 AC power cord 1 x12 AC/DC adaptor 2 x13 Rolling wheel tree stand 8 x14 quick set funnel 12 x15 Tree head section 14 x16 Foot Pedal unit 15 x17 Remote control handset 22 x18 Tree bag - Accessories (small) 28 x19 Tree bag - tree head 29 x110 Tree bag - tree Main 30 x111 hinge pins and washers x112 LED light bulb ?Fig. 7SPARE PARTS ?hinge pins and washersLED light bulb1814293028
ASSEMBLY INSTRUCTIONS MADE IN CHINA8TROUBLESHOOTING GUIDEWARNING: UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE GROW & STOW TREE.A. Adaptor must be plugged into an AC outlet.B. Foot pedal wire must be plugged into a DC jack ofadaptor, and other wires to treeC. Check line voltage - must be 105 to 240 AC volts.A. Set the lock switch to "UNLOCK" positionB.Make sure all wires are properly connected andlocked. (see fig.3)A.Replace a brand new AAA/UM4/LR03 batteriesB.Check batteries polarity diagram inside thebatteries case. (see fig 5)C. Ensure the remote is operated within the range (10 meters)A. Check all connectors of light string (plugs and jacks)are connected on trunk (see main diagram point )B. Extra LED light bulb are included for replace an spareLED light bulbC. Make sure the light string cord is connected to footpaddle and lock with ring screw.(see fig.3)A. Adjust the whole tree to flat ground surface.A. Adjust pull the branches and tips up and out direction.Prevent they cross jam together.B. Press the button again on remote or foot pedal torelease PAUSE (see fig. 4)A. Extra hinge pins are included for repairing the hinges.Insert a new hinge pin through the hold and secureusing the retainer washer (see fig. 7 )A. Adaptor is not plugged InB. Foot pedal wires not connectedC. Low voltageA. Foot pedal set on "LOCK" positionB. wires no connectedA.Batteries out of powerB. Batteries install wrong polarityC. You may out of effective rangeCAUSESOLUTION5SYMPTOM1 No power onRemotecontrol nowork2Tree mechanismdoes notworks673411No light onTree tiltsThe treenot completeup or down Loose Hinge PinA. LED light string connector noconnectedB. LED light bulb missing or damageC. Light string cord no connected toFoot pedalA. Wheel stand set on unflat groundA. Tree branches and Tips make jameach otherB. remote or foot pedal was pressedPAUSE functionFCC VERIFICATION USER MANUALThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.•Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be usedin portable exposure condition without restriction.
ASSEMBLY INSTRUCTIONS MADE IN CHINAIC Caution.RSS-Gen Issue 4 November 2014"&"CNR-Gen 4e éditionNovember 2014:- English: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.- French:Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement.L'appareil a été évalué pour répondre aux exigences générales en matière d'exposition aux radiofréquences. Le dispositif peut être utilisé en condition d'exposition portable sans restriction.

Navigation menu